Lyngdorf Audio Millenium ADC Analog/Digital Converter CD Player User Manual
Contents
1. 11 Channel Toggles down up between inputs 12 Volume Up Down No Funtion 13 Up Down arrows No Funtion LYNGDORF 14 Left Right arrows Navigation adjustment in the menu system Pressing and holding the buttons changes the setting in some menus fast E g Input Gain 15 Enter Selection in menu system 16 Play Pause Stop Skip etc No function 10 BANEIDORF Placement The Millennium ADC should be placed well away from any source of magnetic fields like wall mains adapters Also avoid placing on top of a power amplifier instead place them side by side 0 E NE Y Figure 3 Recommended placing of the Millennium ADC Millennium Link Connection By using the Millennium Link Connection between the Millennium ADC and a Millennium MKkIII or MkIV amplifier from firmware version 40 you are ensured the best possible integration of the two products both in terms of sound quality and ease of use They become one product Connection 1 Connect the two using the enclosed 5 pin XLR cable 2 Select the desired sample rate 48 96 or 192 kHz Please refer to the Sample rate menu 9 c i of this manual 3 Set the Millennium ADC remote control menu to Mill to let the Millennium amplifier control operations when you change the analog inpu2. Right Used to change to total phase 180 degrees To test if left and right channels are in phase is quite easy You just listen for the setting giving the most bass this is also the setting where all instruments are at the right places in the sound stage RANEDORF Technical Specifications Analog inputs Parameter Balanced input connectors 3 pin XLR female gold plated Case Gnd Pin12Gnd Pin2 Hot Pin8 Cold Jinputimpedance iokomm____ __ UR crosstalk 20Hz20KHz Frequency linearity L R 20 20k 0 07dB EEE Hz Frequency response 3dB 10 45k Hz E THD N Ratio A wgt OdbFS 0 000296 114dB Gain OdB S N Ratio THD N A wat 124dB 60dBFS Phono input Input load resistance 20 100 2000r47kOhm___ ___ Input load capacitance 100pForasopF LR crosstalk 20 H2 20 KHz 1008 Frequency linearity L R 20 20k 0 02dB Hz Frequency response 3dB 10 39k Hz Po THD N Ratio A wgt OdbFS 0 0003 113dB S N Ratio THD N A wat 72 122dB Gain 82 28dB 60dBFS Millennium interface Millennium Interface connector 5 pin XLR male gold plated Case Gnd Pin12Gnd Pin2 18 V Pin3 Comm Pin4 RefCIk Pin5 Audio Output sample rate 48kHz 96kHz or 192kHz E 19 20 BANEIDORF Digital outputs Parameter Balanced output connector 3 pin XLR male gold plated Case Gnd Pin12Gnd Pin2 Hot Pin3 Cold Optical output connector Ti Optical output
3. ter 3508S Output protocol SPDIF Toslink consumer AES EBU professional Mains Meis input connector IECS20 o Mains voltage range 110 20VAC 50 60Hz Mains voltage range 220 240V AC 50 60H2 ____ Internal mains fuse ame Mechanical 450 mm 17 72 ONE 430 mm 16 9 Including connectors 145 mm 57 Including feet 12 9 kg 28 41b OOOO Shipping weight 17 2 kg 37 9Ib A 22 RANEIDORF IM TEDORF 23 BANIGDORF www lyngdorf com
4. 0 Treble F5 roll off 10 100 1K 10K 100K Figure 4 Definition of playback de emphasis curve Not used the response is flat from F3 and down 3180 uS 50 Hz 318 pS 500 Hz 75 uS 2122 Hz Not used the response continues to fall with 6 dB octave above F6 Other de emphasis curves available in the Millennium ADC are AES BSI CCIR CCIR 134 DIN 45533 36 37 IEC BS 128 and NAB Select Cartridge The Millennium ADC allows you to make presets for up to 5 different cartridges Select the Cartridge no you wish to set up and continue with the Setup Cartridge menu RANEDORF Setup Cartr 1 Load Preset If you use one of the pre loaded cartridges you can load this directly which then automatically sets up the ADC to this cartridge gain capacitance impedance and DSP cartridge filter If you have a different cartridge you need to make these settings manually If you at a later stage wish to de select a pre loaded cartridge simply select Default in this menu to set this cartridge back to the factory default settings DSP Cart Filter only available for pre loaded cartridges The DSP Cartridge filter compensates the frequency response of the pre loaded cartridges So listening without the filter gives you the raw sound of the cartridge whereas listening with the filter compensates for non linearities When selecting a pre loaded cartridge the DSP cartridge filter is default switched on 50 kHz Zero As ca
5. Owner s manual Millenium ADC Analog Digital Converter BANIGDORF RANEIDORF Table of Contents Unpacking the Millennium ADC Operating Voltage Serial Number Registration Introduction Accessories Front Panel Rear Panel Remote Control Placement Millennium Link Connection Menu Tree Menu Operation Common Menus Digital Sample Rate Communication Adaress Communication Speed Display Timeout Remote Control Factory Reset Phono Input Menus High Pass Filter De emphasis Select Cartridge BUNEIDORF 13 13 13 13 13 13 13 14 14 14 14 Setup Cartr 1 Load Preset DSP Cart Filter 50 kHz Zero Cartridge Gain Cartr Balance Cartr Capacit Cartr Impedance Polarity Analog Input 1 4 Menus Input Gain Polarity Technical Specifications Analog Inputs Phono Inputs Millennium Interface Digital Outputs Mains Mechanical Cleaning and Maintenance Technical Assistance BANEIDORF Unpacking the Millennium ADC Carefully remove the unit and accessory kit from the carton visually check for shipping damage Contact both the shipper and your Lyngdorf Audio dealer immediately if the unit bears any sign of damage from mishandling All Lyngdorf Audio equipment is carefully inspected before leaving our factory Keep shipping carton and packing material for future use or in the unlikely event that the unit needs servicing If this unit i
6. anced 24 bit converters per channel the Millennium ADC sets new performance standards for analog to digital conversion The optional Lyngdorf Audio Phono Stage is a plug in module for the Millennium ADC that allows a gramophone to be connected directly to the Millennium ADC The RIAA equalization in the Lyngdorf Audio Phono Stage is implemented with tight tolerance polypro pylene capacitors To further improve de emphasis possibilities an additional 7 de emphasis curves are available in the DSP for optimal playback of records made before implementation of the RIAA Record Industry Association of America standard IMANEDORF Accessories You should find the following accessories included Millennium Link cable RS 232 cable for firmware 5 pin XLR upgrade from a PC Remote control BUNEIDORF Front Panel Figure 1 Millennium ADC front panel The buttons controls on the front panel of the TDAI 2200 can all be operated either with direct presses or by operating the corresponding keys on the supplied remote control All the keys on the front panel except the Mains switch 1 are duplicated on the remote control as well 1 Mains switch Turns the power to the Millennium ADC on or off 2 Left control button Multifunction button for switching the product on off input selection and menu operation e On Stand by Press to switch the Millennium ADC on from stand by Press and hold the bu
7. lay switch off approximately 10 seconds after the last opera tion As soon as the Millennium ADC is operated the display switches on again for a new 10 seconds period Remote Control Select Off if you do not want the Millennium ADC to respond to it s remote control On if you want it to respond to the remote control default setting and Mill if you want it to respond to the control via a Millennium amplifier Please also refer to chapter 8 Millennium Link Connection of this manual for this connection Factory Reset This restores the Millennium ADC to the factory settings To avoid an unintentional reset you will be prompted one extra time if you are sure you want to do this First when selecting Yes and pressing holding the right control button or pressing Enter on the remote control you are allowed to perform the Factory Reset 13 14 BANEIDORF Phono Input Menus High Pass Filter The high pass filter can be chosen to filter away rumble and or acoustic feedback Available settings are 10 15 or 20 Hz This is referred to as the F2 point in fig 4 De emphasis Records made before 1955 were recorded with different emphasis curves requiring different de empha sis during playback Some records specify the emphasis curve used on their cover but in many cases you have to make an educated guess based on record label and year of release Almost all records after 1955 are recorded with the RIAA emphasis F2 F3 2
8. n be seen from the de emphasis curve fig 6 the treble rolls of from the F 5 point If the 50kHz Zero setting is set on you will add the F6 point at 50kHz resulting in a less pronounced treble roll of Cartridge Gain The Cartridge Gain can be used in two ways 1 The higher the setting the better the S N ratio It should of course always be observed that no clipping occurs 2 Allows you to adjust the sensitivity of the actual cartridge to match other cartridges and or sources The Cartridge Gain can be adjusted from 28 to 82dB in 0 1db steps This allows you to achieve full scale output even with cartridges of very low sensitivity Please refer to the specifications of the cartridge and then use the table in fig 5 as a guide when setting the Cartridge Gain Setting the Cartridge Gain too high will result in distortion So always use your ears when adjusting this If the Phono Clipping message appears on the display when you play back a record you need to decrease the gain The easiest fastest way to adjust the Cartridge Gain is to press and hold the Left Right arrow on the remote control When you save the Cartridge Gain setting the sound will be muted for approximately 5 seconds until the new gain is stabilized 15 16 RANEIDORF Input sensitivity versus cartridge output specification The output voltage of cartridges are generally specified at a stylus velocity of 5 cm sec High performance turntable tone arm cart
9. or differences between left and right channel The balance is adjusted by decreasing the left or right channel between 0 3dB Cartr Capacit The cartridge capacitance can be set to 100 or 430pF Pls refer to the specification of your cartridge to find the correct setting For MM cartridges start with 100pF If this setting sounds too bright use 430pF For MC cartridges use 430pF unless otherwise specified Cartr Impedance The cartridge impedance can be set to 20 100 200 or 47k Ohm 20 200 Ohm is typically used for mov ing coil cartridges and 47kOhm for moving magnet cartridges Pls refer to the specification of your cartridge to find the correct setting For MM cartridges the normal setting is 47k Ohm For MC cartridges start with 200 Ohm If this setting sounds too open select 100 or 20 Ohm until you are satisfied with the sound Polarity With the polarity setting you have the possibility of compensating should the connection somewhere in the chain not be in phase It is recommended to correct any out of phase connections and use this feature as a phase check only Available settings are e Left Right Normal mode e gt Left Right Used if the right channel is out of phase e Left Right Used if the left channel is out of phase e Left Right Used to change to total phase 180 degrees To test if left and right channels are in phase is quite easy You just listen for the setting giving the m
10. ost bass this is also the setting where all instruments are at the right places in the sound stage 17 18 RANEIDORF Analog Input 1 4 Menus Input Gain The Input Gain enables you to match levels from different sources as well as obtaining full scale output on your amplifier The Input Gain can be adjusted up to 18dB in 0 1 dB steps Please refer to the output level specifications of the source and then use the table in fig 6 as a guide when adjusting relative input gain Setting the Input Gain too high will result in distortion Use the table below as a guide but always use your ears when setting the Input Gain The easiest fastest way to adjust the Input Gain is to press and hold the Left Right arrow on the remote control When you save the Input Gain setting the sound will be muted for approximately 5 seconds until the new gain is stabilized 2 3 Y 7 8 9 1 75V 1 25V 750mV 550mV Figure 6 Guide for setting of Input Gain AV V bV V 2V 1V Polarity With the polarity setting you have the possibility of compensating each input should the connection somewhere in the chain not be in phase It is recommended to correct any out of phase connections and use this feature as a phase check only Available settings are Left Right Normal mode Left Right Used if the right channel is out of phase e Left Right Used if the left channel is out of phase Left
11. rent settings to find your personal preference This is due to the fact that there is no simple answer as to what will result in the absolute best sound simply because it depends on many unknown parameters such as the recording the source the complete audio chain the listening room and not least your personal preferences The Millennium Mkl and MkII amplifiers are compatible with 48 and 96 kHz The Millennium MkIII and MkIV amplifiers are compatible with all of the above mentioned sample rates Please also refer to Millennium Link Connection chapter of this manual for connection to Millennium MkII and MkIV amplifiers If using other amplifiers please refer to its specifications to check sample rate compatibility Communication Address The Comm Adaress setting signals the Millennium ADC s identity to the PC interface Addresses 0 99 can be used When choosing an address it must differ from the address of other Lyngdorf Audio product e g the Millennium amplifier is 1 and the Millennium ADC is 2 Communication Speed The Comm Speed setting is the RS232 Link interface speed The default setting is 57600 baud With different PC s and different lengths of cables the settings can be changed to 9600 or 115200 baud The higher the speed the faster the communication however in noisy environments a lower and thus less noise sensitive speed can be preferable Display Timeout Choosing the On setting makes the disp
12. ridge combinations can track up to 50 75 cm sec resulting in an output of 10 to 15 times the output voltage specified for the cartridge The input sensitivity specified for the Millennium ADC is the voltage required for full scale output In the guide fig 5 we have calculated the settings with a track ability of 50cm sec Example Cartridge output voltage specification 4 mV at 5 cm sec Assuming the cartridge has a track ability of 50 cm sec this gives a peak maximum output voltage of 40 mV 50 5 4 and the proper setting for the Millen nium ADC s input sensitivity is 40mV relating to a Cartridge Gain of 41dB Assuming the cartridge has a track ability of 60 cm sec this gives a peak maximum output voltage of 48 mV 60 5 4 and the proper setting for the Millennium ADC s input sensitivity is 50mV closest higher value relating to a Cartridge Gain of 39dB put 5cm sec Gain dB put 5cm sec dB 28 amv 55 29 700uV 7mV 56 30 600uV 6mV 57 31 550uV 58 32 500uV 5mV 59 33 450uV 60 400uV 4mV 61 9mV 34 8mV 35 350uV 62 300 uV 3mV 64 6mV 37 250uV 65 38 200uV 2mV 67 150uV 70 5mV 39 40 100uV 73 90uV 900uV 74 Amv 41 42 80uV 800uV 75 70uV 700uV 76 amv 43 45 60uV 77 2mV 47 55 UV 78 49 50uV 79 53 45uV 80 900u 40uV 81 900uV 9mV 54 Figure 5 Guide for setting of Cartridge Gain BUNEIDORF Cartr Balance The Cartridge Balance adjustment enables you to compensate f
13. s shipped without the original packing damage could occur and void the warranty Operating Voltage The Millennium ADC is selectable to one of the following power ratings 110V 120V at 50 60Hz with a power rating of 50W 220V 240V at 50 60Hz with a power rating of 50W Connect the power input only to the AC source matching the setting shown on the voltage selector switch The warranty will not cover any damage caused by connect ing to inappropriate AC mains The Millennium ADC has three power modes 1 OFF After Power off or Standby the settings of Millennium ADC are retained Please note that some parts of the mains entry section still carry live mains 2 STANDBY In standby mode the Lyngdorf logo will be dimly lit 3 ON In on mode the Lyngdorf logo will be fully lit Serial Number Registration Please record the serial number of your product here for future reference The serial number is en graved in the plaque on the Millennium ADC rear panel You will need this serial number should you ever require service on your Millennium ADC Millennium ADC serial number RANIE DORF Introduction Congratulations on your investment in the Lyngdorf Audio Millennium ADC Analog to Digital Converter The Lyngdorf Audio Millennium ADC is a high performance 2 channel Analog to Digital Converter with 4 line inputs Using a combination of state of the art analog circuitry and Digital Signal Processing to support the two bal
14. s unit to an AC power source Failure to do so may result in serious damage to the unit The warranty will not cover any damage caused by connecting to inappropriate AC mains 6 Phono input RCA connectors 7 Unbalanced analog input RCA connectors 8 Balanced analog input XLR connectors 9 Unbalanced digital output RCA connector 10 Balanced digital output XLR connector 11 Optical digital output Toslink connector 12 Lyngdorf Audio Millennium Link XLR 5 pin connector 13 Mains input IEC 320 connector Remote Control BANEIDORF The remote control is used to access the menu system and replicate the buttons directly accessible on the front panel The four buttons used for selecting which device to control are described below To control the Millen nium ADC the AMP key should be pressed The functionality of the remote control depends on the products in your set up The below description applies to operation of the Millennium ADC only 1 Standby Toggles between on and stand by mode 2 Numerical buttons No function 3 Info Shows the firmware version of the Millennium ADC 4 Digital Analog No function 5 Menu Enters or exits the menu system 6 Mute No function 7 AMP Sets the remote for operation of the Millennium ADC as well as a Lyngdorf Millennium MK III IV Amplifier 8 RCS No function 9 CD Sets the remote for operation of a Lyngdorf CD Player 10 Tuner No function
15. the menu appears or press Menu on the remote control Main Menu ADC Input Gain Pressing the Left Right control buttons or Left Right Arrow on the remote control toggles forwards backwards between the different menus When the requested menu is reached in this case the Display Timeout menu Main Menu ADC lt Display Timeout gt Press and hold the right control button or press Enter on the remote control to access this menu Display Timeout Curr Off New Off Now the setting can be adjusted by pressing the Left Right control buttons or Left Right Arrow on the remote control until the desired setting is reached In this case Display Timeout is set to On Display Timeout Curr Off New On To save the setting press and hold the right control button until the previous menu re appears or press Enter on the remote control Pressing and holding the left control button or pressing Menu on the remote control at any time will exit the menu completely If the actual setting was not saved first you will exit the menu without saving the setting The Millennium ADC will automatically exit the menu if it has not been operated for approximately 30 seconds BUNEIDORF Common Menus Digital Sample Rate Available sample rates are 48 96 and 192 kHz Choice of sample rate depends on the compatibility with the actual amplifier If your amplifier accepts all sample rates we recommend you to test the diffe
16. ts on the Millennium amplifier you will actually change the inputs on the Millennium ADC Please refer to the Remote control menu 9 c v of this manual Millennium Mkl and MkII are not compatible with the Millennium Link Connection In this case you have two options 1 Connect the two using one of the digital outputs e Unbalanced digital output RCA connector SPDIF e Balanced digital output XLR connector AES 2 Update your MkI II to a MkIII version e Please contact your local Lyngdorf Audio dealer for further information RANEDORF Menu Tree Common Menus Main Menu ADC Comm Speed Display Timeout Input Related Menus Input Related Menus Dig Samplerate Comm Address Phono Input Menus Main Menu ADC Select Cartridge Setup Cartr 1 Phono Cartridge 1 Cartridge Gain Common 77 Menus 777 High Pass Filter Exit Cartr Menu pt 2 L 50 kHz Zero Cartr Impedance Analog Input 1 4 Menus Common 777 Menus 11 12 BANEIDORF Menu Operation In the following the general menu operation is described with Display Timeout menu used as an exam ple only The menus available depend on the selected input All settings outside the common menus apply to the selected input only Please refer to the menu tree When The Millennium ADC is switched on select the menu by pressing and holding the right control but ton until
17. tton to switch back to standby mode e Input Selection When the unit is switched ON press to toggle down e Menu Operation Down back button Press to use the down function Press and hold to use the return function See chapter 9 b Menu Operation for a more detailed description 3 Display 4 Lyngdorf logo Dimly illuminated in standby mode Brightly illuminated when the Millennium ADC is on 5 Receiver for the infrared remote control 6 Right control button Multifunction button for switching the product on input selection and menu operation e On Press to switch the Millennium ADC on from stand by e Input Selection When the unit is switched ON press to toggle up e Menu Operation Up select Press to use the up function Press and hold to use the select function See chapter 9 b Menu Operation for a more detailed description IMANEDORF Rear Panel Figure 2 Millennium ADC rear panel 1 Binding post for phono ground 2 Optional phono stage module 3 Millennium ADC serial number label 4 RS 232 AUX and INPUT RJ45 connectors The RS 232 communication connectors are for connection to a computer for firmware upgrade Please visit www lyngdorf com for instructions and available firmware 5 Mains voltage input selector Selects the correct voltage for your location This switch selects either 110 120 V or 220 240 V operation Always check that the correct voltage has been selected prior to connecting thi
Download Pdf Manuals
Related Search