Lindy 25018 Personal Computer User Manual
Contents
1. COMPUTER CONNECTION TECHNOLOGY 5 8 Port Gigabit Desktop Switches User Manual English Benutzerhandbuch Deutsch Manuale d uso Italiano END G Pr Deskoap Switch El NDO u Port kshktop Saith L Eu ui Cri LED Indicators LED Colour Status Description Power is supplied POWER No power A valid link is established LINK ACT Link Activity Data packets received No link is established This port runs at 10Mbps SPEED 10 100 1000Mbps This port runs at 100Mbps Yellow This port runs at 1000Mbps CE LINDY No 25018 25019 FC www LINDY com For Home and Office Use Tested to Comply with FCC Standards LINDY ELECTRONICS LIMITED amp LINDY ELEKTRONIK GMBH FIRST EDITION March 2004 English Manual Installation 1 Operating Environment This switching hub must be installed and operated within the limits of the specified operating temperature 10 55 C 32 131 F and humidity 10 95 non condensing Do not place objects on top of the unit Do not obstruct any vents at the sides of the unit Avoid placing the unit in a location with direct exposure to the sun or near a heat source such as a radiator etc Do not allow water and moisture to enter the unit 2 Connecting the power Connect the output jack of the power adaptor to the power connector at the rear of the switch Plug the adaptor into the mains The green POWER LED on the front panel will light up 3 Connecting to Network Device2. tait pas r solu Manuale Italiano Installazione 1 Parametri Ambientali di funzionamento Questo switch deve essere installato in ambienti con temperature comprese fra 10 e 55 C e umidit fra il 10 e il 95 non condensata Non posizionate oggetti o altro sopra questa unit Non ostruite le griglie di aerazione ed evitate di posizionare questo prodotto in luoghi esposti alla luce diretta del sole o vicino a fonti calori come caloriferi Evitate che acqua o altri liquidi possano penetrare all interno dell unita 2 Connessione dell alimentazione elettrica Collegare il jack in uscita dall alimentatore esterno al connettore presente sul retro dell unita Inserite poi l alimentatore nella presa di corrente Il led verde POWER si accender 3 Connessione degli apparati di rete Nota le porte RJ 45 di questo switch supportano la funzione Auto MDI MDI X Questa evita di dover utilizzare cavi incrociati per il collegamento in cascata di altri apparati Per funzionare in modalita Gigabit Ethernet i cavi di collegamento fra lo switch e gli apparati Gigabit devono essere conformi allo standard Cat 5e per la trasmissione a 1000Mbps La massima distanza fra lo switch e gli apparati connessi di 100m utilizzando cavi a conduttore solido con doppini ritorti cat 5e o superiore Con cavi patch a conduttore multifilare la distanza si riduce in dipendenza della qualit del cavo e della categoria utilizzata Connettete il ca
3. 0Mbits La distance maximale entre un switch et le p riph rique r seau ne doit pas d passer 100m en utilisant un c ble blind Cat 5e ou sup rieure Pour des c bles patch avec fils s par s la distance maximale est r duite en dessous de 100m et d pend de la qualit du c ble employ Connectez un c t du c ble r seau un des ports du switch et connectez l autre c t votre p riph rique r seau Suivez la m me proc dure pour connecter tous les ports Lorsque les deux c t s du c ble sont connect s le LED verte LINK ACT va s allumer Probl mes rencontr s 1 La LED Power n est pas allum e e V rifiez si l alimentation est correctement reli e au secteur et au switch Si cela ne r sout pas le probl me essayez une autre alimentation 12V DC 1 5A au centre Si cela ne fonctionnait toujours pas le switch est certainement d fectueux 2 LINK ACT n est pas allum lorsque connect un appareil e Assurez vous que le p riph rique est connect au switch e Essayez un autre port du switch e V rifiez le c ble s il n est pas endommag ou coup Essayez un autre c ble RJ 45 UTP STP Cat 5e ou plus 3 La LED SPEED n affiche pas 1000Mbps Gigabit bien qu un p riph rique Gigabit 1000Base T soit connect e Assurez vous que la longueur du c ble connect est inf rieure 100m et qu il soit de Cat 5e ou plus Essayez un c ble de qualit sup rieure si le probl me n
4. NDY
5. d Try a different RJ 45 UTP STP Cat 5e or higher cable 3 SPEED LED does not show 1000Mbps Gigabit speed although the connected device is Gigabit 1000Base T compatible e Make sure the RJ 45 UTP STP connection cable is less than 100m in length and at least Cat 5e or higher See remarks above Check if a higher quality Category 6 cable and or different port solves the problem For any further assistance please contact your supplier Deutsches Benutzerhandbuch Installation 1 Installation und Einsatzhinweise Der Switching Hub ist f r den Betrieb in geschlossenen R umen in einem Temperaturbereich 10 55 C vorgesehen Legen Sie keine Gegenst nde auf den Switch Blockieren Sie die Luftzirkulations ffnungen an den Seiten des Geh uses nicht Platzieren Sie den Switch nicht in direktem Sonnenlicht oder neben einer Heizung Sch tzen Sie den Switch vor N sse 2 Anschluss der Stromversorgung Verbinden Sie den Ausgangsstecker des Netzteils mit der Eingangs buchse an der R ckseite des Switch Stecken Sie das Netzteil in eine Steckdose Die gr ne POWER LED leuchtet auf 3 Anschluss der Netzwerkger te Hinweis Die RJ 45 Ports des Switch unterst tzen die Auto MDI X Funktion Dies erlaubt den Einsatz von Standard 1 1 Patchkabel f r alle Verbindungen und macht Cross Over Kabel berfl ssig F r Gigabit Ethernet 1000Base T werden Netzwerkkabel der Cat 5e oder h her ben tigt Die maximale Segmentl nge betr gt 100m m
6. dler Technical Data amp Radio Frequency Energy Certifications Technical Data 5 or 8 Gigabit Ethernet 10 100 1000Base T Ports Autosensing Auto MDI MDI X function Store and Forward Architecture External power supply 12V DC on center 1A 5 port 1 5A 8 port model For inhouse use only Dimensions approx 190 x 100 x 32 mm WxDxH Weight approx 0 6kg without power supply FCC Warning This equipment has been tested and found to comply with the limits for a Class B Digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced technician for hel
7. it Installationskabel Cat 5e oder besser Patchkabel verwenden einen anderen Aufbau Litze Dies reduziert die maximale Segmentl nge sie ist abh ngig von der Qualit t des verwendeten Kabels sowie der Qualit t der angeschlossenen Ger te Verbinden Sie die Ports des Switches mit den RJ 45 Ports der anzuschlie enden Ger te Sobald die Verbindung hergestellt ist und die Ger te eingeschaltet sind leuchtet die gr ne LINK ACT LED Probleml sung 1 Power LED leuchtet nicht Pr fen Sie ob das Netzteil korrekt am Switch und an der Steckdose angeschlossen ist Versuchen Sie ggf ein anderes Netzteil mit 12V DC 1 5A Polarit t in der Mitte Falls dies das Problem nicht l st ist der Switch vermutlich defekt Kontaktieren Sie Ihren H ndler 2 LINK ACT LED leuchtet nicht e Stellen Sie sicher dass das andere Ger t eingeschaltet ist und dessen LED leuchtet Versuchen Sie einen anderen Port am Switch o Pr fen Sie das Netzwerkkabel Versuchen Sie es mit einem h herwertigen Kabel z B Cat 6 3 Die SPEED LED zeigt nicht 1000Mbps Gigabit an obwohl das angeschlossene Ger t Gigabit 1000Base T unterst tzt e Stellen Sie sicher dass das Netzwerkkabel nicht l nger als 100m ist und mindestens Cat 5e oder h her entspricht Bitte beachten Sie obenstehende Anmerkungen Pr fen Sie ob ein h herwertiges Cat 6 Kabel und oder einen anderer Port am Switch das Problem l sen F r weitergehende Probleme kontaktieren Sie bitte Ihren H n
8. p You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment LINDY No 25018 25019 LINDY ELECTRONICS LIMITED amp LINDY ELEKTRONIK GMBH FIRST EDITION March 2004 Manuel en Francais Installation 1 Environnement d utilisation Ce switch r seau doit tre install et utilis dans un environnement relatif au temp ratures mini et maxi qui sont de 10 55 C 32 131 F et d humidit 10 95 non condens e Ne placez pas d objets sur le dessus de l appareil N obstruez pas les ouvertures de ventilation sur le c t de l appareil Evitez de placer l appareil dans un endroit expos directement au soleil ou pr s d une source de chaleur Evitez une p n tration d eau ou de moisissure dans l appareil 2 Connexion de l alimentation Connectez la prise jack de l alimentation directement sur le switch Connectez ensuite l adaptateur la prise de courant La LED d alimentation verte va s allumer 3 Connexion des p riph riques r seaux Remarque Les ports RJ 45 sur le switch supportent la fonction Auto MDI MDI X Cela vous permet d utiliser des c bles droits ou crois s sans aucune importance Cela limine la n cessit d utiliser des c bles crois s Pour l installation d un r seau Gigabit Ethernet les c bles r seaux doivent tre certifi s Cat 5 pour les transmissions de donn es 100
9. s Note The RJ 45 ports on this switch support Auto MDI MDI X This allows the use of straight through cables to connect the switch to a workstation or hub and eliminates the need for crossover cables For Gigabit Ethernet network cables must as a minimum conform to Cat 5e standards for 1000Mbps data transmission When using Cat 5e or higher solid core twisted pair cable the maximum distance between the switch and the connected device is 100m 300 feet For patch cables with stranded cores the maximum distance is reduced to below 100m and depends on the cable quality and Category level Connect one end of the network cable to a port on the rear panel of the switch and connect the other end of the cable to the RJ 45 port on the network device Follow the same procedure to connect all ports Once the network cable is connected at both ends and the attached network device is powered on the green LINK ACT LED will be lit Troubleshooting 1 Power LED is not lit e _ Check the power supply is properly connected to both the mains and the switch If this does not solve the problem try a different mains socket and or power supply 12V DC 1 5A on center If problems persist please contact your supplier 2 LINK ACT is not lit when connected to a device Make sure the attached network device is switched ON and its LED is lit e Try a different port on the switch e Check the network cable make sure it is properly connecte
10. vo ad una porta sul retro dello Switch e alla porta RJ 45 della periferica da collegare Seguite la stessa procedura per tutte le altre periferiche Non appena l apparato connesso alla porta viene acceso si illuminera il corrispondente led verde LINK ACT Risoluzione dei problemi 1 il led Power non si accende e Controllate che l alimentatore sia correttamente inserito nella presa elettrica Se questo non risolve il problema provate a connettere un altro alimentatore a 12V DC 1 5A polo positivo al centro Se ancora lo switch non si accende possibile che lo switch sia danneggiato Contattate il vostro fornitore 2 Il led LINK ACT non si accende quando connettete un apparato di rete e _ Controllate che la periferica connessa sia accesa e che il led sulla periferica stessa sia acceso Se non ottenete risultati provate a connetterla ad un altra porta dello switch e Controllate il cavo di rete appurate che sia integro e che sia di una categoria adeguata Provata ad utilizzare un altro cavo RJ 45 UTP STP Categoria 5e o superiore 3 II led SPEED non segnala una velocit di 1000Mbps Gigabit anche se connessa una periferica GigaBit 1000baseT Controllate che la distanza sia entro i 100m e il cavo almeno di tipo Cat 5e o superiore Provate a connettere gli apparati con cavi Cat 6 o a cambiare porta per migliorare la qualit della connessione Per ogni altro problema tecnico contattate il supporto tecnico LI
Download Pdf Manuals
Related Search