LG Electronics M1717S Computer Monitor User Manual
Contents
1. and setting menus Main menu Sub menu Reference PICTURE BRIGHTNESS To adjust the brightness CONTRAST o contrast and gamma of the screen GAMMA o COLOR PRESET 6500K o To customize the color of 9300K o the screen RED o GREEN o BLUE POSITION HORIZONTAL o To adjust the position of the VERTICAL o sasen TRACKING CLOCK To improve the clarity and PHASE o stability of the screen LANGUAGE i SETUP To customize the screen OSD HORIZONTAL status for a user s operating POSITION VERTICAL o environment WHITE BALANCE o POWER INDICATOR FACTORY RESET o AUDIO VOLUME oO To adjust the audio function Adjustable NOTE a The order of icons may differ depending on the model A10 A13 O On Screen Display OSD Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system Listed below are the icons icon names and icon descriptions of the all items shown on the Menu Press the MENU Button then the main menu of the OSD appears Menu Name PICTURE CONTRAST Icons Fy oe Sub menus GAMMA y gt C MENU NOTE OSD On Screen Display menu languages on the monitor may differ from the manual On Screen Display OSD Selection and Adjustment Main menu Sub menu Description EJ PICTURE BRIGHTNESS To adjust the brightness of the screen CONTRAST To adjust2. Temperature 20 C to 60 C Humidity 5 to 95 non Condensing Attached O Detached Attached Detached O Wall outlet type or PC outlet type a Information in this document is subject to change without notice Display Sync Input Video Input Resolution Plug amp Play Audio Power Consumption Dimensions amp Weight with tilt stand Tilt Range Power Input Environmental Conditions Tilt Stand Signal cable Power cord NOTE Specifications 19inch 19 inches 48 18cm Flat Panel Active matrix TFT LCD Anti Glare coating 19 inches viewable 0 294 mm pixel pitch Horizontal Freq 30 83kHz Automatic Vertical Freq 56 75Hz Automatic Input Form Separate TTL Positive Negative SOG Sync On Green Signal Input 15 pin D Sub Connector Input Form RGB Analog 0 7Vp p 750hm Max VESA 1280 x 1024 75Hz Recommend VESA 1280 x 1024 60Hz DDC 2B RMS Audio Output 1W 1W R L Input Sensitivity 0 7Vims Speaker Impedance 162 On Mode 42W Sleep Mode lt 1W Off Mode 1W Width 44 36 cm 17 46 inches Height 47 56 cm 18 72 inches Depth 23 20 cm 9 13 inches Net 5 98 kg 13 18 Ibs Tilt 325 Swivel 345 AC 100 240V 50 60Hz 1 0A Operating Conditions Temperature 10 to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 95 non Condensing Attached O Detached Attached Detached O
3. Wall outlet type or PC outlet type a Information in this document is subject to change without notice O Preset Modes Resolution Display Modes Resolution Horizontal Freq kHz Vertical Freq Hz 1 VGA 640 x 350 31 469 70 2 VGA 720 x 400 31 468 70 3 VGA 640 x 480 31 469 60 4 VESA 640 x 480 37 500 75 5 VESA 800 x 600 37 879 60 6 VESA 800 x 600 46 875 75 7 MAC 832 x 624 49 725 75 8 VESA 1024 x 768 48 363 60 9 VESA 1024 x 768 60 023 75 10 MAC 1152 x 870 68 681 75 11 VESA 1152 x 900 61 805 65 12 VESA 1280 x 1024 63 981 60 13 VESA 1280 x 1024 79 976 75 Recommend Mode Indicator Mode LED Color On Mode Blue Sleep Mode Amber Off Mode Off How to Install the Rack wall mounting This monitor meets VESA compliant mounting interface pad specifications 1 Separate the stand Cover using a screwdriver as shown in the picture Stand Cover 2 Please the monitor on a piece of cloth or other soft surface with the front side facing downward 3 Separate the stand base using a screwdriver as shown in the picture VESA wall mounting Connected to another object stand type and wall mounted type This monitor accepts a VESA compliant mounting interface pad optional For further information refer to the VESA Wall Mounting Instruction Guide J Kensington Security Slot optional Connected to a locking cable that can be purchased separately at most computer stores Digitally yours sa
4. color level may deteriorate due to video signal distortion Using this function the signal level is adjusted to fit into the standard output level of the video card in order to provide the optimal image Activate this function when white and black colors are present in the screen Use this function to set the power indicator on the front side of the monitor to ON or OFF If you set OFF it will go off If you set ON at any time the power indicator will automatically be turned on Restore all factory default settings except LANGUAGE Press the gt button to reset immediately If this does not improve the screen image restore the factory default settings If necessary perform the white balance function again This function will be enabled only when the input signal is an analog signal Troubleshooting Check the following before calling for service No image appears Is the power cord of the Check and see if the power cord is connected display connected properly to the power outlet Is the power indicator e Touch the Power button light on Is the power on and the Adjust the brightness and the contrast power indicator blue or green Is the power indicator e If the display is in power saving mode try moving amber the mouse or pressing any key on the keyboard to bring up the screen e Try to turn on the PC Do you see an OUT e This message appears when the signal from the OF RAN
5. settings for individual input signals If you want to adjust the monitor while in use or wish to manually run this function once again push the AUTO SET button on the front panel of the monitor Otherwise you may execute the Factory reset option on the OSD adjustment menu However be aware that this option initializes all the menu items except Language Connecting the Display Bottom con Ce 2 Headphone Earphone Input D E Automatically mutes the speaker volume when the headphones are plugged in Audio Input Connects to the LINE OUT jack of the PC sound card lt Display Back gt LINE OUT A terminal used to connect to the speaker including a built in amplifier Amp Make sure that the connecting terminal of the PC sound card is checked before connecting If the Audio Out of PC sound card has only Speaker Out reduce the PC volume If the Audio Out of the PC sound card supports both Speaker Out and Line Out convert to Line Out using the card jumper of the program Refer to the Sound Card Manual lt Jack of the PC sound card gt Control Panel Functions Front Panel Controls MUTE MENU VLIGHTVIEW lt VOL gt AUTO SET Control ap Power Button Function Use this button to turn the display on or off Power Indicator This Indicator lights up blue when the display operates normally On Mode If the display is in Sleep Mode Energy Saving this indicator c
6. GE message PC video card is out of horizontal or vertical on the screen frequency range of the display See the Specifications section of this manual and configure your display again Do you see a CHECK This message appears when the signal cable SIGNAL CABLE between your PC and your display is not message on the connected Check the signal cable and try again screen Do you see a OSD LOCKED message on the screen Do you see OSD You can secure the current control settings LOCKED when you so that they cannot be inadvertently push MENU button changed You can unlock the OSD controls at any time by pushing the MENU button for serveral seconds the message OSD UNLOCKED will appear Troubleshooting Display image is incorrect Display Position is e Press the AUTO SET button to automatically adjust incorrect your display image to the ideal setting If the results are unsatisfactory adjust the image position using the H position and V position icon in the on screen display Check Control Panel gt Display gt Settings and see if the frequency or the resolution were changed lf yes readjust the video card to the recommend e resolution On the screen e Press the AUTO SET button to automatically adjust background vertical your display image to the ideal setting bars or stripes are If the results are unsatisf
7. U button for servaral seconds The message OSD LOCKED should appear You can unlock the OSD controls at any time by pushing the MENU button for servaral seconds The message OSD UNLOCKED should appear MUTE Button Used to select mute on means sound off and mute off means sound on o On Screen Display OSD Control Adjustment Screen Adjustment Making adjustments to the image size position and operating parameters of the display is quick and easy with the On Screen Display Control system A short example is given below to familiarize you with the use of the controls The following section is an outline of the available adjustments and selections you can make using the OSD NOTE a Allow the display to stabilize for at least 30 minutes before making image adjustments To make adjustments in the On Screen Display follow these steps MENU gt VA AUTO SET VA lt gt MENU lt MENU K Press the MENU Button then the main menu of the OSD appears To access a control use the or Buttons When the icon you want becomes highlighted press the AUTO SET Button Use the V A lt gt Buttons to adjust the item to the desired level Accept the changes by pressing the MENU Button QAO Ww Exit the OSD by pressing the MENU Button On Screen Display OSD Selection and Adjustment The following table indicates all the On Screen Display control adjustment
8. User s Guide M1717S M1917S Make sure to read the Important Precautions before using the product Keep the User s Guide CD in an accessible place for furture reference See the label attached on the product and quote this information to your dealer when you require service La Important Precautions This unit has been engineered and manufactured to ensure your personal safety however improper use may result in potential eletrical shock or fire hazards In order to allow the proper operation of all safeguards incorporated in this display observe the following basic rules for its installation use and servicing On Safety Use only the power cord supplied with the unit In case you use another power cord make sure that it is certified by the applicable national standards if not being provided by the supplier If the power cable is faulty in any way please contact the manufacturer or the nearest authorized repair service provider for a replacement The power supply cord is used as the main disconnection device Ensure that the socket outlet is easily accessible after installation Operate the display only from a power source indicated in the specifications of this manual or listed on the display If you are not sure what type of power supply you have in your home consult with your dealer Overloaded AC outlets and extension cords are dangerous So are frayed power cords and broken plugs They may result in a shock
9. actory decrease the visible vertical bars or stripes using the CLOCK icon in the on screen display e Any horizontal noise Press the AUTO SET button to automatically adjust appearing in any your display image to the ideal setting image or characters If the results are unsatisfactory decrease the are not clearly horizontal bars using the PHASE icon in the on portrayed screen display Check Control Panel gt Display gt Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting Set the color setting higher than 24 bits true color e e The screen color is Check if the signal cable is properly connected and mono or abnormal use a screwdriver to fasten if necessary Make sure the video card is properly inserted in the slot Set the color setting higher than 24 bits true color at Control Panel Settings The screen blinks e Check if the screen is set to interlace mode and if yes change it to the recommend resolution Make sure the power voltage is high enough It has to be higher than AC100 240V 50 60Hz Troubleshooting Have you installed the display driver Have you installed the e Be sure to install the display driver from the display driver display driver CD or diskette that comes with your display Or you can also download the driver from our web site http www lge com Do you see a
10. an Le
11. fire hazard Therefore NEVER a Block the bottom ventilation slots by placing the display on a bed sofa rug etc a Place the display in a built in enclosure unless proper ventilation is provided Cover the openings with cloth or other material a Place the display near or over a radiator or heat source Do not rub or strike the Active Matrix LCD with anything hard as this may scratch mar or damage the Active M atrix LCD permanently Do not press the LCD screen with your finger for a long time as this may cause some afterimages Some dot defects may appear as Red Green or Blue spots on the screen However this will have no impact or effect on the display performance If possible use the recommended resolution to obtain the best image quality for your LCD display If used under any mode except the recommended resolution some scaled or processed images may appear on the screen However this is characteristic of the fixed resolution LCD panel On Cleaning a Unplug the display before cleaning the face of the display screen Use a slightly damp not wet cloth Do not use an aerosol directly on the display screen because over spraying may cause electrical shock On Repacking Do not throw away the carton and packing materials They make an ideal container in which to transport the unit When shipping the unit to another location repack it in its original material On Disposal a The fluorescent lamp used in this prod
12. m comfort a Tilt Range 3 25 a Swivel 345 R Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position the forward tilt angle of the monitor should not exceed 5 degrees Connecting the Display Using the Computer 1 Place the monitor in a convenient well ventilated location near your computer 2 Connect the signal cable When attached tighten the thumbscrews to secure the connection O 3 Connect the power cord into a proper power outlet that is easily accessible and close to the display PowerCord Signal Cable Pc audio NOTE Wall outlet type a This is a simplified representation of the rear view This rear view represents a general model your display may differ from the view as shown i z gt Mac adapter For Apple Macintosh use a separate plug adapter is needed to change the 15 pin high density 3 row D sub VGA connector on the supplied cable to a 15 pin 2 row connector 4 Press button on the front switch panel to turn the power on When monitor power is tumed on the Self Image Setting Function is executed automatically PROCESSING SELF IMAGE SETTING NOTE Self Image Setting Function This function provides the user with optimal display settings When the user connects the monitor for the first time this function automatically adjusts the display to optimal
13. n e Make sure to check if the video card supports Unrecognized monitor Plug amp Play function Plug amp Play VESA DDC monitor found message Audio function No sound e Check if the audio cable is correctly connected e Check the volume level Sound level is too low e Check the volume level Display Sync Input Video Input Resolution Plug amp Play Audio Power Consumption Dimensions amp Weight with tilt stand Tilt Range Power Input Environmental Conditions Tilt Stand Signal cable Power cord NOTE Specifications 17inch 17 inches 43 2cm Flat Panel Active matnx TFT LCD Anti Glare coating 17 inches viewable 0 264 mm pixel pitch Horizontal Freq 30 83kHz Automatic Vertical Freq 56 75Hz Automatic Input Form Separate TTL Positive Negative SOG Sync On Green Signal Input 15 pin D Sub Connector Input Form RGB Analog 0 7Vp p 750hm Max VESA 1280 x 1024 75Hz Recommend VESA 1280 x 1024 60Hz DDC 2B RMS Audio Output 1W 1W R L Input Sensitivity 0 7Vims Speaker Impedance 162 On Mode 37W Sleep Mode lt 1W Off Mode lt 1W Width 38 95 cm 15 33 inches Height 43 79 cm 17 24 inches Depth 23 20 cm 9 13 inches Net 5 28 kg 11 64 Ibs Tilt 3 25 Swivel 345 AC 100 240V 50 60Hz 1 0A Operating Conditions Temperature 10 to 35 C Humidity 10 to 80 non Condensing Storage Conditions
14. olor changes to amber AUTO SET Button PROCESSING AUTO IMAGE ADJUSTMENT Use this button to enter a selection in the On Screen Display AUTO IMAGE ADJUSTMENT When adjusting your display settings always press the AUTO SET button before entering the On Screen Display OSD This will automatically adjust your display image to the ideal settings for the current screen resolution size display mode The best display mode is 17 inch monitor 1280x1024 19 inch monitor 1280x1024 Control Panel Functions Front Panel Controls Control Function O lt gt VOL Buttons Use these buttons to decrease or increase the volume level 5 VA Buttons Use these buttons to select or adjust functions in the On Screen Display Lightview hot key DAY This feature lets you easily select the best desired NIGHT image condition optimized to the environment ambient illumination image types etc DAY Bright ambient illumination NIGHT Dark ambient illumination TEXT For text images Word processing etc e MOVIE For animation images in videos or movies PHOTO For pictures or drawings NORMAL This is under normal operating conditions 6 MENU Button Use this button to enter or exit the On Screen Display OSD LOCKED UNLOCKED This function allows you to lock the current control settings so that they cannot be inadvertently changed Press and hold the MEN
15. or fire hazard Call your service technician for replacement Do not Open the Display a There are no user serviceable components inside There are Dangerous High Voltages inside even when the power is OFF a Contact your dealer if the display is not operating properly To Avoid Personal Injury a Do not place the display on a sloping shelf unless properly secured a Use only a stand recommended by the manufacturer To Prevent Fire or Hazards a Always tum the display OFF if you leave the room for more than a short period of time Never leave the display ON when leaving the house a Keep children from dropping or pushing objects into the display s cabinet openings Some intemal parts carry hazardous voltages Do not add accessories that have not been designed for this display a During a lightning storm or when the display is to be left unattended for an extended period of time unplug it from the wall outlet Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord and do not place the display where the power cord is subject to damage Do not use this display near water such as near a bathtub washbow l kitchen sink laundry tub ina wet basement or near a swimming pool Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation If these openings are blocked built up heat can cause failures which may result in a
16. the contrast of the screen CONTRAST eo GAMMA Set your own gamma value 50 0 50 M GAMMA On the monitor high gamma values ee display whitish images and low gamma values display high contrast images COLOR PRESET Select the screen color COLOR OII PRESET amp 500K 9300K i e RED GREEN wm m 50 e 6500K Slightly reddish white e 9300K Slightly bluish white Set your own red color levels e e GREEN Set your own green color levels H 50 Uz e BLUE Set your own blue color levels H POSITION HORIZONTAL To move image left and right POSITION VERTICAL To move image up and down VERTICAL B o 50 TRACKING CLOCK To minimize any vertical bars or E stripes visible on the screen background The horizontal screen size will also change PHASE PHASE BA e 50 M E N UR To adjust the focus of the display This item allows you to remove any horizontal noise and clear or sharpen the image of characters On Screen Display OSD Selection and Adjustment Main menu Sub menu LANGUAGE OSD Honizontar M POSITION VE D o Se WHITE MENUS BALANCE SETUP i WHITE BALANCE gt NO POWER INDICATOR gt ON POWER INDICATOR FACTORY RESET Description To choose the language in which the control names are displayed To adjust position of the OSD window on the screen If the output of the video card is different the required specifications the
17. uct contains a small amount of mercury a Do not dispose of this product with general household waste Disposal of this product must be carried out in accordance to the regulations of your local authority Connecting the Display Before setting up the monitor ensure that the power to the monitor the computer system and other attached devices is turned off Connecting the stand base 1 Place the monitor with its front facing downward on a cushion or soft cloth 2 Align the hooks on the stand base with the matching slots in the base of the monitor 3 Insert the hooks into slots Hook Removing the stand base 1 Place the monitor with its front facing downward on a cushion or soft cloth 2 To remove the stand base hold the bottom of the stand with one hand and pull the base bottom latch with the other hand as shown in the figure Bottom Latch Important a This illustration depicts the general model of connection Your monitor may differ from the items shown in the picture a Once you connect the stand base try not to disconnect it a Do not carry the product upside down holding only the stand base The product may fall and get damaged or injure your foot Connecting the Display a Before setting up the monitor ensure that the power to the monitor the computer system and other attached devices is turned off Positioning your display 1 Adjust the position of the panel in various ways for maximu
Download Pdf Manuals
Related Search