Lexmark 312 Printer User Manual
Contents
1. See the troubleshooting guide on the reverse of this sheet Q lt 3 LEXMARK XP TM gt 3300 Series All In One www lexmark com Unpack your All In One Your All In One may include a Connect the power cord to the power supply Make sure the power light is on Note Contents may vary based on geography photo cartridge instead of a black print cartridge Before you continue remove the photo cartridge from the print cartridge storage unit Note Save the print cartridge s Note You may need to purchase a USB Storage unit to protect any open oe x o Cartridges not in use cable separately Press to scroll to your language Lift the paper support and extend 1 Pull back the transparent deflector Lift the scanner unit and then press Gab the paper exit tray 2 Load the paper flat and to the right 3 Squeeze the paper guide Slide it to the right until it is snug Remove the sticker and tape 1 Open the cartridge lids by pressing the front tabs Close the scanner unit from the print cartridges 2 Insert the cartridges and push them down firmly 3 Snap the lids tight Press gt to print an alignment page Left Right a aD photo color Lf or only black E c0oece e y You may discard the page after it prints CAUTION Do not set up this product or make any electrical or cabling connections such as the power supply cord or telephone during a lightning storm e Use only the2. g in your User s Guide E Have a question Need more supplies ae a another device such as a between the All In One and your Refer to your User s Guide The following cartridge part numbers work with USB hub or switch box computer For help see step 13 e Visit our Web site http support lexmark com your printer Did you remove the sticker Remove the print cartridges check for and tape from the bottom of the sticker and tape and then reinsert e Call us at 1 800 332 4120 each print cartridge the cartriddges For help see steps Monday Friday 9 00 AM 9 00 PM EST Are the print cartridges 7 8 and 9 Saturday Noon 6 00 PM EST installed properly Note Phone number and support times may change without notice Control panel Did you select a language 1 Press the Power button to turn off displays text in the the All In One wrong language 2 Press and hold both the Power and Cancel buttons for 10 seconds Language text appears on the display Press the button repeatedly until the language you want appears on the display Press the Arrow button to select that language Registration information Record the following information located on your store receipt and the back of your printer and have it ready when you contact us so that we may serve you faster Machine Type number Serial number Date purchased Store where purchased P N 23A0170 E C 9E0002 2005 Lexmark International Inc All righ
3. le click My Computer If using Windows XP click Start gt My Computer Double click the CD ROM drive icon If necessary double click setup exe When the All In One software installation screen appears click Install Follow the instructions on the screen Macintosh If you inserted the CD and the installation screen did not appear 1 From your desktop double click the Lexmark 3300 Series Installer icon 2 Double click Install and follow the instructions on the screen Symptom Diagnosis Solution Power light is not lit Is the power cord pushed all Disconnect the power cord from the the way into the All In One wall outlet and then from the All In One Reconnect the power cord by pushing it all the way into the power Supply on the All In One and then into the wall outlet Is the All In One connected to Connect the All In One to an a working electrical outlet electrical outlet that other electrical devices have been using Software will not Is your operating system The All In One supports these install compatible with the operating systems Lexmark All In One s Windows 98 e Windows Me e Windows 2000 e Windows XP e Mac OS X version 10 2 3 and later Alignment page or Is the All In One on Press the Power button If the Power test page will not light does not come on see the print Power light is not lit symptom at the beginning of this table Do you see an error See Error messages message troubleshootin
4. power supply provided with this product or the manufacturer s authorized replacement power supply e Connect the power supply cord to an electrical outlet that is near the product and easily accessible e Refer service or repairs other than those described in the user documentation to a professional service person Steps 12 15 Make sure your computer is on Windows Windows 98 Me Found Now Hardwaro Wizard Found New Hardware Wizard SS ee Found New Hardware Wizard rH a eee A rad Flee Hace Yl ad Welcome to the Found New i Hardware Wizard 7 Thr ura caches bor nea drema bor Sy This wizard helps you install software for Lexmark 3300 Series Lexmark 3300 Series l 4 device dee 6 eres pigra Gil oe 4 hedant draa pod C If your hardware came with an installation CD lt 6 or floppy disk insert it now M aci n to S h What do you want the wizard to do O Install from a list or specific location Advanced ln Click Next to continue M0 o Die 010 o Windows 2000 XP Note New Hardware screens appear only on Windows systems For Macintosh systems continue to step 15 Insert the CD Follow the Windows Setup Trou bleshooting instructions on your If you inserted the CD and the installation screen did not appear computer screen 1 Click Cancel on all New Hardware screens 2 Eject and reinsert the All In One software CD lf the All In One software installation screen does not appear From your desktop doub
5. ts reserved
Download Pdf Manuals
Related Search