Lexmark 110 Printer User Manual
Contents
1. If your printer is already set up make sure the printer power is off and the power cord and any cables are unplugged before installing any options Options compatible with Lexmark T Family printers are labeled with a colored triangle Label locations are indi cated in the illustrations in this book If you encounter a problem while setting up the printer refer to the Lexmark T620 T622 Publications CD Setup Install paper options and printer Oo med amp md Y S t O Some O Soe O 3 5 Bin mailbox page 13 Output expander page 11 High capacity output stacker page 15 Finisher page 10 Envelope feeder Printer page 16 page 7 Print cartridge page 7 Duplex unit page 6 250 Sheet drawer page 5 500 Sheet drawer page 5 2000 Sheet drawer page 4 Option install order may be reversed Install memory and option cards Printer flash memory page 19 5 Access printer system board Option cards page 17 page 21 Load print material See page 23 Attach cables 4 See page 24 Network printing page 24 Local printing page 25 Verify setup D A See page 27 Configure for TCP IP 6 See page 29 Install printer drivers See page 31 ee C Network printing page 31 Local printing page 33 Step 1 Install paper options and printer The table illustrates various combinations of paper options supported by your printer All models s2. Network printing The following instructions explain how to install printer drivers on printers attached to a network Windows Ports The following network printer ports are supported e Microsoft IP port Windows NT 4 0 and Windows 2000 e Lexmark network port Windows 95 98 Me Windows NT 4 0 and Win dows 2000 Printer drivers Note Using the Lexmark T Family custom printer driver and a Lexmark network port provides enhanced functionality such as printer status alerts The following printer drivers are supported e Windows system printer driver e Lexmark T Family custom printer driver System drivers are built into Windows operating systems Custom drivers are available on the drivers CD Updated system and custom drivers are available on the Lexmark Web site at www lexmark com drivers 31 32 Macintosh UNIX Linux Printing methods The following network printing methods are supported e Direct IP printing e Shared printing point and print peer to peer Creating ports and installing drivers Read the detailed instructions on the drivers CD Click View documentation and look for network printer installation If you choose to install without using the instructions on the drivers CD you need a basic understanding of network printing on TCP IP networks printer driver installation and the process involved in adding new network ports Your Lexmark T Family printer connects automatically to AppleTalk networks
3. Warning The output expander tray is designed to hold the weight of print material only Do not use it as a shelf excess weight may cause it to disengage from the output expander 1 Remove the top cover from the printer fin isher or high capacity output stacker Note If you have purchased a finisher or a high Capacity output stacker that output option must be installed directly on the printer before the output expander 11 12 Mounting bracket Mounting slot 2 Slide the plastic bracket onto the static brush holder located on the bottom of the output expander 3 Insert the mounting brackets into the slots on top of the printer or output option Make sure the output expander is seated securely 4 Place the tips of the wire paper bail into the ends of the plastic bracket so that the bail curves downward The bail rests in the output tray of the expander below it or in the printer output bin Note Do not attach the paper bail unless you are mounting the output expander on the printer or another output expander 5 Slide the lower tabs on the tray into the lower slots on the output expander 6 Rotate the tray up until the upper tabs click into the upper slots 7 Attach the top cover to the output expander Installing a 5 bin mailbox The5 bin mailbox is shipped with a sheet of labels and a plastic bracket for attaching a paper bail Mailbox N After you carefully unpack the mailbox insta
4. and becomes readily visible to other network clients You must create a printer object icon on the desktop of each network client using the LaserWriter 8 printer driver and the Lexmark T Family PostScript Printer Description PPD file Note A PPD file provides detailed information about the capabilities of a printer to UNIX or Macintosh drivers or applications A printer object icon must be created on the desktop of each network client using the LaserWriter 8 printer driver and the Lexmark T Family PostScript Printer Description PPD file Specific information about installing the printer on your Apple Talk network can be found in the online documentation on the drivers CD that shipped with your printer A Lexmark PPD Installer is provided in the downloadable Web package available on the Lexmark Web site at www lexmark com Depending upon which drivers CD shipped with your printer you may also find this software on the drivers CD Launch this utility and follow the instructions to install the PPDs Send a test print job when you have finished Your printer supports many UNIX platforms such as Sun Solaris and Linux Note The Sun Solaris package is located both on the drivers CD and on the Lex mark Web site at www lexmark com drivers Lexmark provides a printer driver package for each supported UNIX platform con taining all the necessary drivers and PPDs The user s guide contained in each package gives detailed instruction
5. been installed A drawer consists of a paper tray and a support unit The 250 sheet drawer and the 500 sheet drawer are installed the same way 1 Remove the tray from the support unit Remove all packing material and tape from both the support unit and the tray 2 Place the support unit on top of any previously installed paper drawers or the table or printer cabinet where you plan to use the printer The tab round peg and square holes on top of any drawer help you seat the support unit so the edges are aligned properly Make sure the support unit is securely in place 3 Attach another optional drawer a duplex unit or the printer e To attach a drawer repeat steps 1 and 2 e To attach a duplex unit see Installing a duplex unit on page 6 e To attach the printer see Setting up the printer on page 7 Installing a duplex unit Back cover Lexmark T Family label Tab Square hole Round peg The duplex unit attaches under the printer below the standard input tray and above any paper drawers Refer to the Lexmark T620 T622 Publications CD for details about using the duplex unit 1 Place the duplex unit on top of any installed paper drawers or the table or printer cabinet where you plan to use the printer The tab peg and holes on top of any drawer help you seat the duplex unit so the edges are aligned properly Make sure it is securely in place 2 Attach the printer See Setti
6. to the Ready state 29 Verifying the IP settings Configure for Pull 30 Printing ImageQuick 1 Print another network setup page and make sure the IP Address Netmask and Gateway are what you expected Use the information in Printing a network setup page on page 27 if you need help 2 Ping the printer and verify that it responds For example at a command prompt on a network computer type ping fol lowed by the new printer IP address DING XXX XXX XXX XX If the printer is active on the network you should receive a reply If your printer has an ImageQuick optional firmware card installed you can con figure for Pull Printing once an IP address has been assigned to your printer For detailed configuration instructions refer to the online documentation on the ImageQuick CD The ImageQuick CD is shipped with printers that have the ImageQuick optional firmware card pre installed and also with the firmware card if you purchased it separately Step 7 Install printer drivers o SsaA seeeesee A printer driver is software that lets your computer communicate with your printer The following table is a quick guide to finding the specific instructions you need Network Windows Ethernet or Token Ring connections Windows 95 98 Me Windows NT 4 0 Windows 2000 0 Wi UNIX Linux Local Windows parallel or USB connections Windows 95 98 Me Windows NT 4 0 Windows 2000 UNIX Linux
7. LEXMARK Lexmark T620 and T622 Setup Guide Edition January 2001 The following paragraph does not apply to any country where such provisions are inconsistent with local law LEXMARK INTERNATIONAL INC PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Some states do not allow disclaimer of express or implied warranties in certain transactions therefore this statement may not apply to you This publication could include technical inaccuracies or typographical errors Changes are periodically made to the information herein these changes will be incorporated in later editions Improvements or changes in the products or the programs described may be made at any time Comments about this publication may be addressed to Lexmark International Inc Department F95 032 2 740 West New Circle Road Lexington Kentucky 40550 U S A In the United Kingdom and Eire send to Lexmark International Ltd Marketing and Services Department Westhorpe House Westhorpe Marlow Bucks SL7 3RQ Lexmark may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you You can purchase additional copies of publications related to this product by calling 1 800 553 9727 In the United Kingdom and Eire call 0628 481500 In other countries contact your
8. Performing Self Test appears on the operator panel display After the printer completes its internal tests the Ready message indicates the printer is ready to receive jobs If you see other messages on the display refer to the Lexmark T620 T622 Publications CD for instruc tions on clearing the message Click Printing and then click Understanding printer messages Go to Printing a menu settings page on page 28 If you attached the printer to a network see Printing a network setup page You can change the language that appears on the operator panel display Refer to the Lexmark T620 T622 Publications CD for instructions If the printer is attached to a network print a network setup page to verify the network connection This page also provides important information that will help you con figure for network printing 27 28 Printing a menu settings page 1 2 Note 4 Press Menu until you see Utilities Menu and then press Select Press Menu until you see Print Net Setup and then press Select to print the page The network setup page prints and the printer returns to Ready status Check the first section on the network setup page and confirm that Status is Connected If an optional MarkNet card is installed in slot 1 you see Print Net1 Setup If the card is installed in slot 2 you see Print Net2 Setup If Status is Not Connected your LAN drop may not be active o
9. able FAR provisions Lex mark International Inc Lexington KY 40550 FCC emissions information This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Any questions on this statement should be directed to Director of Lab Operations Lexmark International Inc 740 West New Circle Road NW Lexington KY 40550 859 232 3000 Refer to the Lexmark T620 T622 Publications CD for details Safety information e f your product is NOT marked with this symbol o t MUST be connected to an electrical outlet that is properly grounded e The power cord must be connected to an electrical outlet that is near the product and easily accessible e Refer service or repairs other than those described in the operating instructions to a professional service person e This product is designed tested and approved to meet strict global safety standards with the use of specific Lexmark components The safety features of some parts may not always be obvious Lexmark is not responsible for the use of other replacement parts e Your product uses a laser exercise CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure e Your product uses a printing
10. artridge down as it drops and snaps into place f Close the upper front door Attach decals to the paper trays Decals showing the number 1 are on your printer and the standard input tray These decals keep the standard input tray paired with the printer Peel the decals from the sheet and attach them to the recessed areas on the drawer and the matching tray 4 Attach the operator panel overlay If English is not your preferred language Pleat panel attach the overlay with the appropriately d translated names for the operator panel a Peelthe protective backing off the over lay b Align the holes in the overlay with the buttons on the operator panel and press it into place C Rub the overlay firmly to make sure it adheres securely to the operator panel d Peel the protective covering away from the overlay 5 Attach the paper bail If you will be installing a finisher or 5 bin mailbox skip to step 6 a Remove the printer top cover and slide the plastic bracket onto the static brush holder Adjust the bracket so it is cen tered over the area where paper exits b Place the tips of the wire paper bail into the ends of the plastic bracket so that the bail curves downward C Replace the top cover 6 Attach output options See e Installing a finisher on page 10 e Installing an output expander on page 11 e Installing a 5 bin mailbox on page 13 e Installing a high capacity outp
11. cables A 10BaseT 100BaseT X Fast Ethernet port is standard on the Lexmark T622n You can add a Token Ring or 10Base2 Ethernet port to either printer model by installing an optional MarkNet internal print server To attach the printer to a network 1 Make sure the printer is turned off and unplugged 2 Connect the printer to a LAN drop or hub using standard cabling that is compatible with your network The printer automatically adjusts itself for the network speed Token Ring Ethernet 10BaseT or Ether net 100BaseTX networks Category 5 use an RJ 45 connector P S505 C JOD Q N CO Local printing Token Ring networks Shielded Twisted Pair use a DB9 connec tor Ethernet 10Base2 networks Thin Coax use a BNC T connector You can attach your printer locally using either the standard USB port or parallel port A USB port is standard on all printer models We rec ommend Lexmark USB cable part number 12A2405 2 m The standard parallel port requires an IEEE 1284 compliant parallel cable We recommend Lexmark parallel cable part number 1329605 10 ft or 1427498 20 ft If you add a parallel port by installing an optional USB Parallel Interface Card you need a 1284 A C parallel cable such as Lexmark part number 43H5171 9 8 ft Note Some UNIX Linux and Macintosh computers also support USB connec tions Consult your computer docu mentation to see if your system suppor
12. card Save the packaging 4 Holding the firmware card by its sides align the two pins on the card with the holes on the system board Orient the card so that the pins are closest to the edge of the board 5 Push in until the firmware card is firmly in place Installing an option card MarkNet internal print server MarkNet N2501e or N2401e Tri Port adapter USB Parallel 1284 C interface card hard disk with adapter Warning Electronic components are easily damaged by static electricity Touch something metal on the printer before you touch the card Connector 1 Connector 2 O N N ee N bi N coe N NS N ee So Your printer has two connectors that support the following option cards Hard disk with adapter card MarkNet internal print server USB Parallel 1284 C Interface Card Parallel 1284 C Interface Card Coax Twinax Adapter for SCS Tri Port Adapter Refer to the documentation included with each card for detailed information about that specific card You need a small Phillips screwdriver to install these options Note The Lexmark T622n model ships with an Ethernet print server already installed Follow the steps in Accessing the printer system board beginning on page 17 Locate the card connectors on the system board If you are installing only one card install it in connector 1 If you are installing two cards on a model with multip
13. ize your printer memory capacity and connectivity by adding optional cards The instructions in this section help you install any of the following options Printer memory Flash memory Tri Port Adapter USB Parallel 1284 C Interface Card Parallel 1284 C Interface Card MarkNet internal print servers also called internal network adapters or INAs Hard disk Optional firmware card Accessing the printer system board You must access the printer system board to install printer memory flash memory or an option card 1 Make sure the printer power is off the printer power cord is unplugged and all cables are disconnected from the back of the printer 2 Press the release latches to open the upper and lower front doors 17 Screws Tab 18 3 Press down on the side door latches and CLE Ee open the side door ee Ke Vy 4 Loosen but do not remove the six screws on the shield You need a small Phillips screwdriver to loosen these screws Note Screws are used to give added protection against memory theft 5 Use the tabs to slide the shield up until the top three screws fit into the three keyholes on the shield 6 Hold the shield by the tabs and lift it off Installing printer memory or flash memory Memory connector 1 cen Memory connector 2 gt Memory connector 3 Warning Electronic components can be damaged by static electricity Touch something metal
14. le connectors use connector 1 first and then connector 2 Locate the two screws on the back of the printer that attach the metal plate to the slot Remove and save the two screws Remove and discard the plate Unpack the card Save the packaging materials 21 22 a A A a oa r J SS ro e yf Ae SS A A N z SN Sk ae NJ a Ng S VAS Reattaching the shield and closing the doors WEA GA NI Cin AAS KN 6 Align the connection points on the card with the connector on the system board and push the card firmly into the system board connector 7 Insert the two screws saved from the metal plate or the extra screws shipped with the card into the holes 8 Tighten the screws to secure the card After you have installed option cards on the printer system board follow these steps to reattach the shield and close the doors 1 Grasp the shield by the tabs and align the three keyholes on the shield with the top three screws Holding the shield by the tabs slide it down onto the screws Tighten all six screws 2 Close the side door 3 Close the upper and lower front doors Note If you have not completed the section Setting up the printer beginning on page 7 do so now Step 3 Load print material eee _ t SO Width guide tab Length guide AS LK lever gt Wid
15. ll it i immediately otherwise the edges of the mounting brackets could damage tabletops or fabrics Labels K Lexmark T Family label Warning The 5 bin mailbox is designed to hold the weight of print material only Do not use it as a shelf excess weight may damage it 1 Remove the top cover from the printer fin isher output expander or previously installed mailbox Note If you have purchased a finisher or a high capacity output stacker that output option must be installed directly on the printer before the mailbox 2 Slide the plastic bracket onto the static brush holder located on the bottom of the 5 bin mailbox Note If the mailbox will be the topmost output option remove the paper bail from the bracket on the top cover and store ina safe place 13 Mounting bracket 14 Mounting slot Insert the mounting brackets into the slots on top of the printer finisher output expander or previously installed 5 bin mailbox Make sure the mailbox is seated securely Attach the top cover to the mailbox Place the tips of the wire paper bail into the ends of the plastic bracket so that the bail curves downward The bail rests in the output tray of the expander below it or in the printer output bin Adjust the paper stops for the appropriate paper size Attaching labels to output options Labels Installing a high capacity ou
16. nd on the Lex mark Web site at www lexmark com drivers Lexmark provides a printer driver package for each supported UNIX platform con taining all the necessary drivers and PPDs The user s guide contained in each package gives detailed instructions for installing and using Lexmark printers in UNIX environments All the driver packages support local printing using a parallel connection The driver package for Sun Solaris systems also supports USB connections to Sun Ray appliances and Sun workstations You can download these printer driver packages from Lexmark s Web site at www lexmark com drivers Depending on which drivers CD shipped with your printer you may also find the driver package you need on the CD LEXMARK P N 11K3092 E C 1K0911 Lexmark and Lexmark with diamond design are trademarks of Lexmark International Inc registered in the United States and or other countries 2001 Lexmark International Inc 740 West New Circle Road Lexington Kentucky 40550 www lexmark com
17. ng up the printer on page 7 Setting up the printer inorder to ensure adequate clearance when installing system board options see Install mem ory and option cards on page 17 before you posi tion the printer if e You plan to install memory or option cards and e You will have less than 605 6 mm 24 in clearance on the left side of the printer CAUTION Make sure your fingers are not under the printer when you set it down 1 Ask someone to help you lift the printer by the handholds and lower it onto the duplex unit optional drawer table or printer cabinet The tab round peg and square holes on top of any drawer or the duplex unit help you seat the printer so the edges are aligned properly Make sure the printer is securely in place Handhold tap Square hole Round peg 2 Remove the print cartridge packaging a Push the release latch and open the printer upper front door b Grasp the print cartridge by the hand grip and pull the print cartridge up and out Print cartridge Warning Never touch the photoconductor drum on the under side of the print cartridge c Pull on each end of the plastic V shaped piece and then pull the packaging mate rial straight out Discard all packaging material d Align the slides on the print cartridge with the slots on the print cartridge cradle Use the colored arrows inside the printer for placement e Guide the print c
18. on the printer before you touch the memory option Note Some memory and firmware options offered for other Lexmark printers cannot be used with your printer Refer to the Lexmark T620 T622 Publications CD for specifications Follow the steps in Accessing the printer system board beginning on page 17 Unpack the memory option Avoid touching the connection points along its edge Save the packaging materials Open both latches on the connector completely Insert the memory option straight into the connector with the connection points pointing toward the system board Push the memory card firmly into the connector until it snaps into place Make sure each latch fits over the notch located on either side of the option card Follow the steps in Reattaching the shield and closing the doors beginning on page 22 19 Installing an optional firmware card Warning Optional firmware cards are easily damaged by static electricity Touch something metal on the printer before you touch a card Resting posts Card Connectors 20 Follow the instructions in this section to install an optional firmware card The system board has one connection point for firmware cards 1 Access the system board See page 17 for instructions 2 Locate the holes on the system board near the option card connectors 3 Unpack the firmware card Avoid touching the metal pins on the bottom of the
19. ons The following printer connections are supported e Parallel Windows 95 98 Me Windows NT 4 0 and Windows 2000 e USB Windows 98 Me and Windows 2000 Note Using the Lexmark T Family custom printer driver provides enhanced func tionality such as printer status alerts Printer drivers The following printer drivers are supported e Windows system printer driver e Lexmark T Family custom printer driver System drivers are built into Windows operating systems Custom drivers are available on the drivers CD 33 34 Macintosh UNIX Linux Updated system and custom drivers are available at www lexmark com drivers Installation instructions Read the detailed online instructions on the drivers CD Click View documentation and look for information about local printer installation Detailed instructions are provided for parallel and USB connections If you are setting up the printer for local printing you need to install the Lexmark T Family PPD and use it with the LaserWriter 8 printer driver or the Adobe Post Script driver The Lexmark T Family PPD and specific information about local printer installation on Macintosh computers can be found on the drivers CD that shipped with your printer After the printer is installed print a test page to verify your printer is correctly set up Your printer supports many UNIX platforms such as Sun Solaris and Linux Note The Sun Solaris package is located both on the drivers CD a
20. point of purchase References in this publication to products programs or services do not imply that the manufacturer intends to make these available in all countries in which it operates Any reference to a product program or service is not intended to state or imply that only that product program or service may be used Any function ally equivalent product program or service that does not infringe any existing intellectual property right may be used instead Evaluation and verification of operation in conjunction with other products programs or services except those expressly designated by the manufacturer are the user s responsibility Lexmark and Lexmark with diamond design MarkNet and MarkVision are trademarks of Lexmark International Inc registered in the United States and or other countries Sun Sun Microsystems Sun Ray Solaris and the Solaris logo are trademarks or registered trademarks of Sun Microsystems Inc in the U S and other coun tries and are used under license Other trademarks are the property of their respective owners Copyright 2001 Lexmark International Inc All rights reserved UNITED STATES GOVERNMENT RESTRICTED RIGHTS This software and documentation are provided with RESTRICTED RIGHTS Use duplication or disclosure by the Government is subject to restrictions as set forth in subparagraph c 1 ii of the Rights in Technical Data and Computer Software clause at DFARS 252 227 7013 and in applic
21. process that heats the print media and the heat may cause the media to release emissions You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions Conventions Warning A warning identifies something that could damage your printer hardware or software CAUTION A caution identifies something that could cause you harm Getting started E T l 137 16 cm afa a 4 5 ft l 304 8 mm 304 8 mm 12 in 12 in CDs Paper bail QR and bracket Operator panel overlay non English only Handhold lt lt Power switch____e cover 5 Power cord Tray number decals Lexmark 500 sheet drawer Lexmark T T Family T622 model only Family T622 model only Turn off the printer Options compatibility Troubleshooting Select a well ventilated place to set up your printer Allow at least as much space as shown in the illus tration Make sure you have a sturdy low table or the optional printer stand on which to set the printer 2 Remove all items from the box except the printer If any items are missing contact the place where you bought the printer Save the carton and packing material in case you need to repack the printer for service or storage Note Leave the printer in the box until you are ready to install it Then ask someone to help you lift the printer using the handholds
22. r your network cable may be malfunction ing Consult your network support person and then print another network setup page to verify that you are connected to your network Save the network setup page for use with later instructions See Printing a menu settings page Print the menu settings page to review the default printer settings and to verify that printer options are installed cor rectly For more information about using the printer opera tor panel and changing menu settings refer to the Lexmark T620 T622 Publications CD 1 2 Press Menu until you see Utilities Menu and then press Select Press Menu until you see Print Menus and then press Select to print the page The message Printing Menus is displayed Verify that the options you installed are listed under Installed Features If an option you installed is not listed turn the printer off unplug the power cord and reinstall the option Verify the amount of memory installed is correctly listed under Printer Information Verify that the paper trays are configured for the sizes and types of paper you loaded in the printer Step 6 Configure for TCP IP EE If you have TCP IP available on your network we recommend that you assign an IP address to the printer Setting the printer IP address If your network is using DHCP an address is automatically assigned 1 2 Look for the address under the TCP IP heading on the netwo
23. rk setup page you printed in Printing a network setup page on page 27 Go to Verifying the IP settings on page 30 and begin with step 2 Note You can find instructions for other methods of setting the IP address in the online documentation on the drivers CD that shipped with your printer If your network is not using DHCP then you must manually assign an IP address One of the easiest ways is to use the operator panel 1 2 oO o1 A Q 10 11 Press Menu until you see Network Menu and then press Select Press Menu until you see Standard Network and then press Select Standard Network appears if you purchased a printer with an on board net work port If you have an optional MarkNet card installed in slot 1 you see Network Option 1 If the card is installed in slot 2 you see Network Option 2 Press Menu until you see Std Net Setup and then press Select Press Menu until you see TCP IP and then press Select Press Menu until you see Set IP Address and then press Select Change the address by pressing Menu to increase or decrease each number Press Select to move to the next segment Press Select when you are finished The message Saved appears briefly Press Menu until you see Set IP Netmask and then press Select Repeat step 6 to set the IP Netmask Press Menu until you see Set IP Gateway and then press Select Repeat step 6 to set the IP Gateway When you are finished press Go to return the printer
24. s for installing and using Lexmark printers in UNIX environments NetWare Local printing Windows You can download these printer driver packages from Lexmark s Web site at www lexmark com drivers Depending on which drivers CD shipped with your printer you may also find the driver package you need on the CD Your Lexmark T Family printer works with both Novell Distributed Print Services NDPS and regular queue based NetWare environments Novell Distributed Print Services NDPS If you have an NDPS environment we recommend you install the Lexmark NDPS IP Gateway The gateway tightly integrates your printers with NDPS so you can easily monitor control and print to them You can get the gateway the snap ins the support files and a white paper with installation instructions on the Web at www lexmark com networking ndps html Additional information about network printer installation can be found at www lex mark com publications or on the drivers CD that shipped with your printer Non NDPS queue based For the latest information about Lexmark support for non NDPS queue based environments click View Documentation on the drivers CD and look for network printer installation This documentation is also available on the Lexmark Web site at www lexmark com publications The following instructions explain how to install a printer driver on a printer attached to a computer using a parallel or USB connection Supported connecti
25. th guide Paper size indicators N Ma Width guide tab Width guide D OS SE Paper capacity mark 1 2 3 Note Complete these instructions to load print material into any of the standard or optional trays All paper trays are loaded in the same way Remove the paper tray Pull the width guide tab and slide the width guide to the far right side of the tray Squeeze the length guide lever and slide the length guide to the correct position for the size paper you are loading If a finisher is installed on the printer see the Lexmark T Family Quick Reference or the Lexmark T620 T622 Publications CD for special paper loading instructions Place the paper into the paper tray with the recommended print side face down for single sided printing and face up for duplex printing Do not fill paper above the paper capacity mark fill line Pull the width guide tab and slide the width guide to the left until it lightly rests against the edge of the paper stack Adjust the knob to show the size of the paper currently loaded Note This setting serves as a visual reminder 7 only it has no effect on the operation of the printer Reinstall the tray 23 Step 4 Attach cables eee S eh 24 Network printing You can attach your printer to a network or locally directly to a computer You can attach your printer to a network using stan dard network
26. tput stacker If you purchased an output expander or 5 bin mail box you received a sheet of labels for your various output bins The illustration indicates some places where you may attach the labels output bin tray paper stop side cover or wherever best suits your needs Lexmark T Family printer models T622 and T620 support one high capacity output stacker The high capacity output stacker is packaged with installation instructions Note The high capacity output stacker must be positioned directly on the printer and before other output options It cannot be used with the finisher 15 16 Installing the envelope feeder Lexmark T Family label Release latch Envelope feeder connector door The envelope feeder attaches to the front of your printer behind the lower front door It can be removed when you are not using it making the printer more compact Refer to the Lexmark T620 T622 Publications CD for details about using the envelope feeder 1 Push the release latch and open the printer lower front door 2 Lift open the envelope feeder connector door 3 Align the tabs on the envelope feeder with the slots on both sides of the printer and then gently push the envelope feeder into the opening until it snaps into place The envelope feeder tilts downward at a slight angle when it is installed properly Step 2 Install memory and option cards O s s sM sGeeesed You can custom
27. ts USB If you have installed an optional Tri Port Adapter or if you are using a non network 25 26 model you can locally attach the printer with a serial cable We recommend Lexmark part number 1038693 50 ft For details on LocalTalk or infrared connec tions refer to the documentation that shipped with the Tri Port Adapter Note All Windows operating systems support parallel cable connections However only the Windows 2000 98 Me operating systems support USB cable connections To attach the printer to a computer 1 Make sure the printer computer and any other attached devices are turned off and unplugged 2 Connect the printer to the computer using a parallel or USB cable Use an IEEE 1284 compliant parallel cable to ensure that you can access all of your printer s functions Be sure to match the USB symbol on the cable to the USB symbol on the printer Step 5 Verify printer setup eee t O Turning on the printer Printing a network setup page 1 Note Plug one end of the printer power cord into the socket at the back of the printer and the other end into a properly grounded outlet Turn on the printer If the printer is attached locally directly to a computer leave the computer and any other attached devices turned off You will turn these on in a later step The printer requires time to warm up after you turn it on During this period the message
28. up port a duplex unit and envelope feeder Finisher High capacity output stacker Output expander 5 Bin mailbox O Attach up to Three output expanders u Two 5 bin mailboxes t One of each or One high capacity output stacker or p One output expander and one high capacity output u stacker or t One finisher and one output expander or One finisher and one 5 bin mailbox r n e r Lexmark T622 n Lexmark T620 n Attach up to Attach up to n Three optional drawers Four optional drawers u 2000 Sheet drawer 250 Sheet drawer 500 Sheet drawer Duplex unit Envelope feeder Installing the 2000 sheet drawer Your printer supports one 2000 sheet drawer It gives your printer added capacity by letting you load up to four reams approximately 2 000 sheets of 20 Ib paper The 2000 sheet drawer is packaged with a User s Guide that contains detailed instructions for instal lation setup and use including loading paper and removing paper jams When you have finished installing the 2000 sheet drawer install any other drawers or an optional duplex unit that you may have purchased Lexmark T Family label colored triangle Installing a 250 sheet or 500 sheet drawer Tray labels gt Lexmark T Family label colored triangle Support unit Tab Square hole Round peg Paper drawers attach under the printer and optional duplex unit The printer automatically rec ognizes any drawer that has
29. ut stacker on page 15 Installing a finisher Lexmark T Family label colored triangle Warning The finisher tray is designed to hold the weight of print material only Do not use it as a shelf excess weight may damage it Mounting slot 10 The finisher is shipped with a staple cartridge already installed After you carefully unpack the finisher install it immediately otherwise the edges of the mounting brackets could damage tabletops or fabrics 1 Remove the top cover or any previously installed output options from the printer Note The finisher must be positioned directly above the printer and below other output options It cannot be used with the high Capacity output option 2 Insert the mounting brackets into the slots on top of the printer Make sure the finisher is seated securely 3 Place the tips of the wire paper bail into the ends of the plastic bracket so that the bail curves downward The bail rests in the printer output tray 4 Attach the top cover to the finisher Plastic bracket Wire paper bail Installing an output expander Each output expander consists of the expander and a removable tray A paper bail bracket and Lexmark T Family labels are also included label After you carefully unpack the output expander install it immediately otherwise the edges of the mounting brackets could damage tabletops or fab rics Output expander Bracket and bail
Download Pdf Manuals
Related Search