Kenwood DDX4049BT Car Video System User Manual
Contents
1. The unit may be damaged or fail to ork if you share the wires or ground them to any metal part in the car After the unit is installed check whether the brake lamps blinkers wipers etc on the car are working properly Mount the unit so that the mounting angle is 30 or less This unit has the cooling fan page 5 to decrease the internal temperature Do not mount the unit in a place where the cooling fan of the unit are blocked Blocking these openings will inhibit the cooling of the internal temperature and result in malfunction Do not press hard on the panel surface when installing the unit to the vehicle Otherwise scars damage or failure may result WI Wi English 3 Connection Connector A Ground wire Black Battery wire Yellow Ignition wire Red Connector B Antenna Cord Orange White Dimmer control wire Orange White ag ss ILLUMI Connect to the vehicle s parking brake detection switch harness Sa Parking sensor wire Light Green e PRKSW For the sake of safety be sure to connect the parking sensor uit Reveres sensor wire Purple White Connect to vehicle s reverse lamp harness when using the optional rear view camera WWWWYWWM Steering remote control input Light Blue Yellow To steering remote EP E T2. Use only the screws provided f you use the wrong screws you could damage the unit fthe power is not turned ON PROTECT is displayed the speaker wire may have a short circuit or touched the chassis of the vehicle and the protection function may have been activated Therefore the speaker wire should be checked ake sure that all wire connections are securely made by inserting jacks until they lock completely f your vehicle s ignition does not have an ACC position or if the ignition wire is connected to a power source with constant voltage such as a batterv wire the power will not be linked with the ignition i e it will not turn on and off along with the ignition If vou want to link the unit s power with the ignition connect the ignition wire to a power source that can be turned on and off with the ignition kev Use a commerciallv available conversion connector if the connector does not fit in the vehicle connector Insulate unconnected wires with vinyl tape or other similar material To prevent a short circuit do not remove the caps on the ends of the unconnected wires or the terminals If the console has a lid make sure to install the unit so that the faceplate will not hit the lid when closing and opening If the fuse blows first make sure the wires aren t touching to cause a short circuit then replace the old fuse with one with the same rating Connect the speaker wires correctly to the terminals to ich they correspond
3. Optional Accessory Connection cable Included in the Navigation System ASSENZA Connection cable Included in the TV tuner 8 DDX5022 DDX5022Y DDX52RY Installation for Monitor Player Unit Firewall or metal support Screw M4X8 commercially available Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place Self tapping screw Metal mounting strap commercially available commercially available E Make sure that the unit is installed securely in place If the unit is unstable it may malfunction eg the sound may skip Installing the Escutcheon Accessory 8 English 9 Removing Monitor Player Unit Removing the Hard Rubber Frame escutcheon 1 Engage the catch pins on the removal tool 2 and remove the two locks on the lower level Lower the frame and pull it forward as shown in the figure gt Removal Tool Accessory The frame can be removed from the top side in the same manner 2 When the lower level is removed remove the upper two locations 10 DDX5022 DDX5022Y DDX52RY Removing the Unit 1 Remove the hard rubber frame by referring to the removal procedure in the section lt Removing the Hard Rubber Frame gt 2 Remove the Hex head screw with integral washer M4 x 8 on the back panel 3 Insert the two removal tools 2 deeply into the slots on each side as shown Removal To
4. KENWOOD MONITOR WITH DVD RECEIVER DDX5022 DDX5022Y DDX52RY INSTALLATION MANUAL Kenwood Corporation Accessories 2 DDX5022 DDX5022Y DDX52RY Installation Procedure wo OND To prevent short circuits remove the key from the ignition and disconnect the terminal of the battery Make the proper input and output wire connections for each unit Connect the wire on the wiring harness Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle Take Connector A on the wiring harness and connect it to the external power connector on your vehicle Connect the wiring harness connector to the unit nstall the unit in your car Reconnect the terminal of the battery Press the reset button AWARNING If you connect the ignition wire red and the battery wire yellow to the car chassis ground you may cause a short circuit that in turn may start a fire Always connect those wires to the power source running through the fuse box A ounting and wiring this product requires skills and experience For safety s sake leave the mounting and wiring work to professionals ake sure to ground the unit to a negative 12V DC power supply Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing Do not use your own screws
5. ent damage to the unit A4 Yellow Battery The default connection for the wiring harness is described in ji en DITA 1 below If the ISO connector pins are set as described in 2 A7 Red gnition ACC or 3 make the connection as illustrated AS Black Earth Ground Please be sure to reconnect the cable as shown 2 below to Connection install this unit to the Volkswagen vehicles etc Speaker Connector 1 Default setting The A 7 pin of the vehicle s ISO B 1 Purple Rear Right connector is linked with the ignition and the A 4 B 2 Purple Black Rear Right pin is connected to the constant power supply B 3 Gray Front Right Ignition cable Red A 7 Pin B 4 Gray Black Front Right gt B 5 White Front Left Unit Vehicle B 6 White Black Front Left gt S 8 7 Green Rear Left Battery cable Yellow A 4 Pin B 8 Green Black Rear Left 2 The A 7 pin of the vehicle s ISO connector is connected to the constant power supply and the A 4 pin is linked to the ignition Ignition cable Red A 7 Pin gt gt Ba Battery cable A 4 Pin Yellow w The A 4 pin of the vehicle s ISO connector is not connected to anything while the A 7 pin is connected to the constant power supply or both the A 7 and A 4 pins are connected to the constant power supply Ignition cable Red A 7 Pin Re Unit me gt e Vehicle e Battery cable Yellow A 4 Pin When the con
6. nection is made as in 3 above the unit s power will not be linked to the ignition key For that reason always make sure to turn off the unit s power when the ignition is turned off To link the unit s power to the ignition connect the ignition cable ACC red to a power source that can be turned on and off with the ignition key 6 DDX5022 DDX5022Y DDX52RY System Connection USB device USB terminal commercially available C cole Do not connect Audio Input Resistance free stereo type mini plug 3 50 Visual Input Resistance free mini plug 3 50 Rear View Camera Input Visual input Yellow Audio Visual Output Visual output Yellow Front Preout Audio left output White Audio right output Red Rear Preout Subwoofer Preout Audio left output White Audio right output Red I Audio Visual Output Audio left output White Audio right output Red English 7 Optional Accessory Connection iPod DJ commercially available KCA iP300V Optional Accessory Audio Output Black Visual Output Yellow Visual Input Yellow I USB terminal USB terminal Navigation System Optional Accessory Audio Input Black KCA BT200 input Optional Accessory TV Tuner
7. o use the steering wheel remote control feature you need to an exclusive remote adapter not supplied matches your car is required When this terminal is not in use leave its cap on Connect to the terminal that is grounded when either Mute wire Brown the telephone rings or during conversation E To connect the Kenwood navigation system consult your navigation manual Power control Motor antenna control wire Connect either to the power control terminal when using the optional Blue White power amplifier or to the antenna control terminal in the vehicle If no connections are made do not let the cable come out from the tab 4 DDX5022 DDX5022Y DDX52RY Cooling fan FM AM antenna input JASO FUSE 15A Wiring harness Accessory REVERSE REMO CONT ANT CONT PCONT MUTE English 5 Connecting Wires to Terminals Connector Function Guide AWARNING Pin Numbers for Cable Colour Functions Connecting the ISO Connector ISO Connectors The pin arrangement for the ISO connectors depends on External Power he tvpe of vehicle vou drive Make sure to make the proper Connector connections to prev
8. ol Accessory 2 4 Lower the removal tool toward the bottom and pull out the unit halfway while pressing towards the inside Be careful to avoid injury from the catch pins on the removal tool 5 Pull the unit all the way out with your hands being careful not to drop it KENWOOD
Download Pdf Manuals
Related Search