JVC LST0979-001B Security Camera User Manual
Contents
1. 24 Rotate both pan 175 and rotation 100 from the positions aligned with the camera s shooting direction mark pan center mark and rotation center mark Be sure to hold the rotation knob and adjust the rotation without holding the lens unit Loosen the tilt fastening screw before performing tilt adjustment After adjusting the field angle tighten and secure the tilt fastening Screw so that the field angle will not be misaligned Moving the camera beyond its adjustable range may deteriorate the performance of this camera As this camera has a wide tilt rotation range a part of this camera may appear on the screen depending on the field angle and direction Do not hold the lens unit when adjusting the camera direction Applying force on the lens unit may damage it Adjustment 4 Adjust the image size Loosen the fastening screw for the zoom adjustment ring and move the ring to the left right to adjust the image size After adjustment is complete fasten the screw 5 Adjust the focus Hold the focus adjust gear knob shift the catch from point A to point B as illustrated in the diagram to disengage the gear To prevent the gear shaft from breaking when the gear is opened too far out from B remove the gear shaft from the bearing C in diagram In this case re insert the shaft back into the bearing C and return it to the original position before using 2 Loosen the fastening screw for the focus a2. We will not be responsible for any inconveniences or disturbances caused in the event of privacy invasion as a result of camera footages of this product W Others When using this camera with AGC set to MID or HIGH the sensitivity increases automatically for dark images and the screen may appear grainy but this is not a malfunction If the DAY NIGHT switch is turned to AUTO the mode changes automatically to black and white in dark places As the sensitivity level is increased in this case the screen may appear grainy and more white spots may appear When Switching between modes the brighter area on the screen is emphasized and visibility may be reduced However this is not a malfunction When shooting an extremely bright object e g lamp the image on the screen may have white vertical tailings smear or expansion blooming may appear around it This is a characteristic of the CCD and not a malfunction When the white balance of this camera is set to ATW N or ATW W and depending on the conditions of the object the color tone may differ slightly from the actual color due to the principle of the automatic tracking white balance circuit This is not a malfunction When this camera is used under high temperatures vertical stripes may appear on the screen This is a characteristic of the CCD and not a malfunction When this camera is moved from a cold to warm place condensation may occur and the camera may not work In th
3. c page 15 Power Supply Cable c page 11 page 15 Hole for Connecting Cables Conduit Hole rs page 20 Base gt page 19 Dome Cover Fastening Screw x3 c page 13 Introduction Name of Parts Continued Camera Interior The dome cover and inner dome are removed Focus Adjustment Ring page 25 Zoom Adjustment Ring t page 25 Q Rotation Knob gt page 24 o Fall Prevention Wire To prevent the dome cover from dropping t page 13 Q Camera Unit Fastening Screw x2 page 19 8 Introduction Space for Inserting Heater When mounting the heater sold separately KA ZH215U read the instruction manual of the heater before mounting Power Supply Connector for Heater For connecting to the power supply connector of the heater Tilt Fastening Screw x2 page 24 MONITOR Terminal RCA pin t page 23 Lug Plate c page 16 Space for Inserting Silica Gel c page 16 Focus Adjust Gear t page 25 Shooting Direction Mark page 24 Pan Center Mark page 24 Rotation Center Mark gt page 24 Function Selection Switches page 12 MENU Button Display the menu screen Refer to the attached manual MENU SETTING for more details about setting the menu Status Indication Lamp Lights up when the power is turned on A v 4 FY SET Button This allows user to select menu scr
4. AWG 18 1 6 mm 140 m 450 ft 350 m 1100 ft 120 m 390 ft AWG 14 d 2 0 mm 220 m 720 ft 550 m 1800 ft 180 m 590 ft AWG 12 Note e If thin cables are used the resistance of the cables will be high and a significant voltage drop will occur when the camera is at its maximum power consumption Either use a thick cable with low resistance or place the power supply near to the camera and shorten the length of the cable to restrict the voltage drop at the rated current of camera to below 10 If voltage drop occurs during operation the performance will be unstable Do not connect the AC 24 V cable to commercial power supply If it is connected by mistake the internal circuit may be damaged Do not use the camera and make sure to send it to the nearest JVC dealer for inspection Do not connect DC 12 V and AC 24 V cables at the same time When connecting the DC 12 V cables ensure that the polarities are correct Color of the cables red 12 V black GND When using a DC 12 V power supply ensure that the polarities of the cable are correct 11 Setup Setting the Switches Before mounting the camera set the function setting switches on the camera To set the switches use a fine tipped screwdriver DIP Switch Settings Chart m x RE D N AUTO OFF 7728010510 4 1 LCD CRT NOTUESD Function selection switc
5. after connection t page 16 Adjusting images page 23 Mounting the dome cover rs page 17 20 Installation Mounting the Camera Using the Conduit Hole at the Side of the Base If the camera cannot be mounted directly to the ceiling use the conduit hole at the side of the base to mount the camera to the pipe Conduit hole G3 4 14 UNC TK C2201WPU M25 TK C2201WPE Remove the dome cover and inner dome page 13 2 Remove the camera unit from the base and mount the fall prevention wire to the camera unit Refer to Mounting the Camera Using the Conduit Hole at the Bottom of the Base gt page 19 step 2 3 Wind the sealing tape Wind the sealing tape around the pipe junction where the conduit hole thread lines with the pipe screw hole two or more times 4 Remove the conduit plug from the base Loosen the mounting screw x 6 mm using flathead screwdriver and remove the conduit plug at the side of the base 5 Mount the conduit plug that was removed to the conduit hole at the bottom of the base 6 Mount the base to the pipe Screw the pipe to the conduit hole at the side of the base When screwing the pipe do not screw beyond 12 mm Doing so can damage the camera interior Conduit plug 3 Sealing tape Mounting screw 7 Refer to Mounting the Camera Using the Conduit Hole at the Bottom of the Base page 19 step 6 to 9 21 Installation Mounting the Camera Continued Mo
6. water or moisture to enter thereby fogging the lens and dome cover 2 Remove the silica gel provided from its bag and insert in the position as shown in the diagram 72 272 27 This illustration is plate such that for the purpose of it will not drop explanation Silica gel L lat silica GP gel with the lug A The camera unit is not shown here Silica gel insertion space When mounting the camera under raining conditions make sure that rain does not enter into the camera Be sure to use the silica gel provided Failure to do so may fog up the camera lens and dome cover f you are not adjusting the camera angle soon after mounting the camera insert the silica gel provided only after adjustment Prolonged exposure to air will make the silica gel provided less effective 16 Installation W Adjusting images After mounting is completed adjust the images while checking the actual image t page 23 W Mounting the Dome Cover Attach the dome cover back when all settings are finished 1 Mount the inner dome Mount the inner dome in a way that supports the tilt direction of the lens Insert the inner depression of the inner dome into the protruding parts beside the fastening screw Push it in until it is fixed by the catches 2 locations Catches x 2 Inner depression Inner dome 17 Installation Mounting the Camera Continued 2 Mount
7. JVC OUTDOOR DOME CAMERA TK C2201WPU INSTRUCTIONS For USA and Canada TK C2201WPE For Europe For Customer Use Enter below the Serial No which is located on the body Retain this information for future reference Model No TK C2201WPU TK C2201WPE Serial No LST0979 001B Introduction Contents Introduction Goritents OEA TETEE d UN M Led s 2 Features Operating Precautions Name of Parts Setup About Connection Cables Setting the Switches Installation Mounting the 0211615 555555255525555552555255525525552555255525525552555255555525552555 5 52555 13 Adjustment Adjusting Image Adjusting the Auto White Balance Others 1 29 Introduction Thank you for purchasing this product Before use please read this INSTRUCTIONS and the information materials included to ensure proper use of this product These instructions are for TK C2201WPU TK C2201WPE TK C2201WPE is not evaluated by UL Features Easy DAY NIGHT function TK C2201WPU DAY NIGHT surveillance with auto IR cut filter on off Color B amp W shooting TK C2201WPE 3D noise reduction SDNR 4 areas privacy mask Built in display mode CRT or LCD selectable Outdoor ready vandal and tamper resistant structure complies with IP66 How to read this manual Conventions and symbols Indicates operating precautions Indicates reference data regar
8. ation then readjust the white balance AWC ERROR HIGH LIGHT Excessive Illumination Displayed when the light is too bright Decrease the illumination then readjust the white balance AWC ERROR TIME OVER Subject movement Displayed when the subject moves Keep the subject still then readjust the white balance 28 Others Specifications Horizontal resolution Video S N ratio Minimum illumination Zoom ratio Focal length Maximum aperture ratio Minimum aperture Angle of view Angle adjustment range Power supply Power current consumption Mass Ambient temperature 550TV lines typical 52 dB typical AGC OFF Color mode 0 05 Ix typical 50 96 F1 2 AGC HIGH Black and White mode 0 03 Ix TK C2201WPU typical 50 F1 2 AGC HIGH 0 006 Ix TK C2201WPE typical 50 F1 2 AGC HIGH 3 75 2 8 10 10 5 F 1 2 f 2 8 F 2 7 f 10 5 mm Equivalent to F 360 f2 2 8 mm 99 5 H x 73 2 V f210 5 mm 27 4 H 20 6 Pan 175 Tilt 80 Rotation 100 AC 24 V 60 Hz DC 12 V UL Listed Class 2 power supply only TK C2201WPU 24 V 50 Hz 60 Hz DC 12 V TK C2201WPE 2 3 W TK C2201WPU 220 mA TK C2201WPE when using heater KA ZH215U 20 W TK C2201WPU TK C2201WPE approx 1 3 kg 10 C to 50 C 14 F to 122 F Operation 0 C to 40 C 32 F to 104 F Recommended when
9. ding limitations on functions usage and the like var Indicates a reference page or item Contents of this manual JVC holds the copyright to this manual Any part or all of this manual may not be reproduced without prior consent from the company Product names of other companies described in this manual are trademarks or registered trademarks of the respective companies Symbols such as 9 and are omitted in this manual Design specifications and other contents described in this manual are subject to change for improvements without prior notice Introduction Operating Precautions Storage and Location of Use Do not install the camera in the following places In a place with vapor or oil for example in a kitchen When the ambient temperature rises above or falls below the acceptable range from 10 to 50 In a place at which corrosive gases are emitted Near a source of radiation X rays strong radio waves or magnetism In a place subject to vibration In a place with excessive dirt Using this unit in the vicinity of the transmitting antenna of a radio or TV devices that emit strong electromagnetic waves such as a transformer or motor or wireless devices such as a transistor or mobile phone may give rise to noises in the image and changes in its color Do not install in an environment where there is cold air or near the air outlet of an air conditioner The do
10. djustment ring and move the ring to the left right to adjust the focus Knob Focus adjustment ring Cath Zoom adjustment ring Focus adjust gear 25 Adjustment Adjusting Image Continued 6 Fine adjust the focus Press and hold the A button Focus adjust mode will be activated and FOCUS ADJUST MODE is displayed on the monitor screen The contours are emphasized as the iris opens and the depth of field becomes shallow After adjustment press V lt 1 51 1500 to exit focus adjust mode The mode is also automatically deactivated after about 30 seconds Memo During the focus adjust mode the electronic shutter will function automatically As a result the screen will appear grainy This is not a malfunction 2 Shoot the subject Return the catch to A in the diagram and then rotate the knob to adjust the focus to the optimum position Rotate the focus adjust gear knob one base pitch in the direction of the arrow in the diagram to correct the focus shift when mounting the dome cover 5 Peel off the protection sheet temporarily and cover the dome cover to check the focus After checking paste the protection sheet back on the dome cover One base pitch 26 Adjustment 7 Tighten the fastening screw of the focus adjustment ring Hold and press the focus adjust gear between your fingers in the direction of the arrows in the diagram and tighten the fastening screw of the focus adju
11. ectly to the ceiling or on the wall When mounting to a wall replace areas indicated as ceiling in the procedures by wall W Preparing the camera 1 Remove the dome cover screws x3 2 Remove the inner dome from the catches two locations The inner dome can be easily removed by turning it about 45 degree and grip from both sides near the catches as illustrated in the diagram Doom cover xcd p Wrench supplied lt FF 2 Inner dome Catches x 2 Fall prevention wire 13 Installation Mounting the Camera Continued W Mounting the Camera Unit 1 Make a hole 930 mm in the ceiling using the template provided 2 Mount the fall prevention wire for connecting the camera unit to the ceiling The fall prevention wire is not provided Prepare a wire taking into due consideration the length strength pull and material insulating D Remove the fall prevention wire fastening screw on the bottom of the camera unit to mount the fall prevention wire Mount the fall prevention wire at a structurally strong location 3 Mount the camera unit to the ceiling Pull the cables from the ceiling and camera towards the lens as illustrated in the diagram align the tt mark to the shooting direction and mount the camera to the ceiling Align the tt mark upwards when mounting the camera the wall Fall prevention wire not supplied Camera unit W Fall prevention wire 1 6 and be
12. eens and change or confirm settings Fine Focus Adjustment page 26 Auto White Balance Adjustment page 28 Setup About Connection Cables The maximum connection distance varies with the type of cable used Be sure to turn off the power of devices before connecting cables To video Signal Cable gt To Power Supply Memo Connect to AC 24 V power supply if using the heater sold separately KA ZH215U Video signal cable coaxial cable Connect a 75 Q coaxial cable BNC such as RG 59 to the video signal output connecter BNC 10 Setup DC 12 V or AC 24 V power supply cable Connect the power cord to the DC 12 V or the AC 24 V power supply The unit is to be powered by a UL Listed Class 2 power supply only For USA and Canada The AC 24 V and DC 12 V power supply shall conform to the following UL Listed Class 2 power supply only Class 2 not wet and Class 3 wet wiring For USA Isolated power supply only For Europe This installation shall be in accordance with the National Electrical Code ANSI NFPA 70 The following table shows the connection distances when 2 core VVF vinyl insulated vinyl sheath cables are used Reference value Conductor Maximum Maximum Maximum diameter connection connection connection distance DC 12 V distance AC 24 V distance 24 V not using heater not using heater using heater 1 0 mm 50 m 160 ft 130 m 420 ft 40 m 130 ft
13. g screw on the base to mount the fall prevention wire The fall prevention wire is not provided Catches x 2 19 Installation Mounting the Camera Continued 3 Wind the sealing tape Wind the sealing tape around the pipe junction where the conduit hole thread lines with the pipe screw hole two or more times 4 Mount the base to the pipe Turn and screw the base unit to the pipe in the clockwise direction When screwing the pipe do not screw beyond 12 mm Doing so can damage the camera interior 5 Secure the base unit to the ceiling Use the M4 screw x2 to secure the base firmly to the ceiling Make sure there is gap between the ceiling and the base The M4 screws not provided Use a suitable type of screws according to the material of the mounting location 6 Mount the fall prevention wire to a structurally strong location 3 Sealing 12 mm and below y 58 M4 mm screw 7 Connect the cables page 15 Push the connector of the connected coaxial cable back to the pipe 8 Mount the camera unit to the base Push in until the catch 2 locations snaps Make sure that the cables and the fall prevention cable are not caught between the camera and the base during mounting 2 Fasten the camera unit fastening screw 2 locations to secure the camera 9 The procedures for the following are the same as that for normal camera mounting Process
14. hes 1 D N AUTO OFF Day amp Night Switch Set this to AUTO when shooting a subject with continually changing brightness day night The image switches to color when the subject is bright and black and white when it is dark The image is set to color at all times when OFF is selected Default setting AUTO Memo You can set the image to black and white at all times using the menu TK C2201WPE only 2 BLC OFF ON Backlight Compensation Selector Switch Set this to ON when shooting in backlight The subject becomes easier to see as brightness is adjusted according to the photometry area set AREA of the menu Default setting OFF Memo Refer to AREA in the MENU SETTING separate 3 MONITOR TYPE LCD CRT Monitor Type Selector Switch Set this to LCD or CRT according to the monitor in use Default setting LCD Memo Refer to LCD TYPE in the MENU SETTING separate 12 Installation Mounting the Camera Selecting a mounting method Mount directly to the ceiling or on the wall page 13 Mounting the Camera Using the Conduit Hole at the Bottom of the Base rs page 19 Mounting the Camera Using the Conduit Hole at the Side of the Base page 21 Mounting the Camera using the Electrical Box page 22 When mounting the camera to the ceiling ensure to wear safety glasses to protect the eye from any falling objects Mounting the camera dir
15. is case leave the camera under room temperature for about one hour before turning on the power When the power supply voltage is momentarily disrupted or drops due to lightning turning on the air conditioner or the like image distortion or noise may occur When the power supply voltage of the camera drops the input protection circuit inside the camera operates and the camera may be turned off Make use of a voltage rating within 10 for the camera s power supply voltage This unit enlarges the rotation angle to support wide range set up When the zoom of the lens is set to WIDE end and the tilt angle is set around 80 a part of this camera appears in the image depending on the rotation angle In this case adjust the image angle if necessary page 24 To prevent fogging resulting from temperature changes be sure to insert the silica gel at the location specified rs page 16 The 3D noise reduction function of this camera may result in afterimage of a moving subject Afterimage is more likely to occur when using the camera with DNR LEVEL set to HIGH This is not a malfunction Introduction Name of Parts Camera Mounting Hole x 2 page 14 Fall Prevention Wire Mounting Screw t 14 Conduit Plug Hole side page 21 Dome Cover t page 13 Q Inner Dome t page 13 Video signal output connector t page 10 page 15 Introduction Protection Cover
16. low 912 and below Shooting direction 24 1 86 5 mm mark Po V3 24 mm x 2 not supplied The screws for mounting the camera are not provided Use a suitable type of screws according to the material of the mounting location 14 Installation W Connecting the cable For safety reasons turn on the power only after all the connection is complete The status indicator lights up when the camera is turned on Connect the coaxial cable page 10 Lower the protection cover and connect the connectors Upon connecting restore the protection cover to cover the connectors This will isolate and protect the metallic parts of the connectors 2 Connect the power supply cable page 11 3 Wrap insulation tapes around the connecting parts of the power supply cables Wrapping insulation tapes will improve future work conditions as well as reduce penetration by noise and other objects 4 Wrap the insulation tape 5 rn the connector of the connected coaxial cable back to the ceiling Insulating tape 1 yl Z Bind insulating tape Power supply cable 15 Installation Mounting the Camera Continued W Process after connection Fill the conduit hole and mounting holes with sealing agent and insert the silica gel 1 Fill the conduit hole and the screw mounted holes 2 locations with sealing agent GE silicon Seal the holes completely Failure to do so may cause
17. me cover may become foggy as a result of sudden temperature changes Though this camera is IP66 compliant there is no guarantee against water seepage under any circumstances IP66 evaluation was not conducted by UL Maintenance Clean the dome cover lens using a lens wiper cloth or a tissue For tough stains wipe with a neutral detergent diluted with water followed by wiping with a dry cloth Do not use benzene or thinner to wipe the camera Doing so may melt the surface or cause it to fog W Energy Conservation When the camera is not in use for a long time turn off the power for safety and energy conservation reasons Copyright Protection With the exception of the user being the copyright holder or when permission Such as for duplication has been granted by the copyright holder permission is required in principle for the duplication modification or transmission of copyrighted material Unauthorized duplication modification or transmission of copyrighted material may constitute a copyright infringement and the user may be liable to compensate for any damages When using copyrighted material be sure to check the license agreement of the copyrighted material thoroughly When rights or rights holders are involved with regard to the targeted duplicating subject permission may be required for shooting or using processing it Be sure to check the licensing conditions thoroughly Introduction W Disclaimer
18. stment ring Focus adjustment ring d Adjustment Adjusting the Auto White Balance Each light source has its own color temperature Therefore when the main light source lighting the subject is changed adjust the white balance again 1 Press the MENU button 2 Select WHITE BALANCE with the A W button and AWC with the lt gt button then press the SET button 3 Zoom in to fill the screen with white Place a white object at the center of the screen under the same lighting condition as the subject to be shot and zoom in to fill the screen with white 4 Press the SET button Auto white balance adjustment begins During operation AWC OPERATION is displayed on the screen 5 Adjustment is complete When the appropriate white balance is acquired AWC OK is displayed SET button MENU button D AWC SET AWC SET R GAIN 160 R GAIN 160 B GAIN 160 B GAIN 160 AWC OPERATION AWC OK AY lt P button AWC OPERATION _ AWC OK during operation adjustment completed W Error display If auto white balance adjustment is not successful the following messages will appear on the monitor AWC ERROR NG Subject error Displayed when there is not enough white color on the subject or the color temperature is not suitable Fill the screen with a white object thoroughly and adjust the white balance again AWC ERROR LOW LIGHT Insufficient Illumination Displayed when the light is low Increase the illumin
19. the dome cover D Clean the dust and dirt on the dome cover 2 Align the position marks 3 locations on the camera unit and dome cover followed by pressing in directly to mount the cover 3 Tighten the dome cover fastening screw Position alignment mark x 3 Dome cover ___ Dome cover protective sheet Eg Ensure that the silica gel provided has been inserted before mounting the dome cover Be sure to secure the dome cover firmly If it is not firmly secured the cover can drop or the humidity inside the camera can increase and fog up the interior of the cover When the cover is removed again after mounting the dome cover the field angle may changed If the field angle is changed re adjust the focus and the field angle Ensure that the fall prevention wire of the dome cover is not caught between the dome cover and the base Failure to do so may prevent the dustproof and waterproof functions from working properly 18 Installation Mounting the Camera Using the Conduit Hole at the Bottom of the Base Conduit hole G3 4 14 UNC TK C2201WPU M25 TK C2201WPE Remove the dome cover and inner dome rs page 13 2 Remove the camera unit from the base and mount the fall prevention wire to the camera unit CD Loosen the camera unit fastening screw 2 locations with a screwdriver Press the catch 2 locations inwards and remove the camera from the base 8 Remove the fall prevention wire fastenin
20. unting the Camera using the Electrical Box 1 Remove the dome cover and inner dome t page 13 2 Mount the camera unit to the electrical box Mount the camera unit to the electrical box using the mounting hole 2 locations with the M4 screw 2 pieces Memo The screws are not provided 4 Inch square 2 electrical box 3 The procedures for the following are the same as that for normal camera mounting Connecting the cable page 15 Process after connection page 16 Adjusting images page 23 Mounting the dome cover gt page 17 22 Adjustment Adjusting Image After mounting the camera adjust the images while looking at the actual image Discharge the static electricity from your body by touching the metallic part of the monitor terminal before handling the camera as static electricity may cause the camera to malfunction 1 Mount the monitor Connect the monitor terminal of this camera to a monitor to adjust the camera s shooting direction image and focus 2 Turn on the camera Monitor terminal 750 terminal Monitor 23 Adjustment Adjusting Image Continued 3 Adjust the shooting direction of the camera Adjust the camera for pan tilt and rotation and face the camera towards the subject Shooting direction mark Pan center mark Rotation center mark Rotation knob x2
21. using heater KA ZH215U 30 C to 50 C 22 F to 122 F Operation 20 C to 40 C 4 F to 104 F Recommended 29 Others Specifications Continued Accessories 30 TK C2201WPU WARRANTY CARD x 1 INSTRUCTIONS x 3 Silica gel x 1 Wrench x1 Template x 1 TK C2201WPE INSTRUCTIONS x 5 Silica gel x 1 Wrench 1 Template x 1 Others W External dimensions Unit mm inch 121 4 3 4 1 13 4 1 2 AP 42 1 5 8 Screw for conduit Ser bottom surface side surface TK C2201WPU G3 4 14 UNC TK C2201WPE M25 160 6 1 4 Specifications and appearance of this camera are subject to change for improvements without notice 31 10 10410102 91 119 31100 3004110 JVC 2009 Victor Company of Japan Limited LST0979 001B
Download Pdf Manuals
Related Search