JVC GR-DV1 Digital Camera User Manual
Contents
1. Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 324392 A Nortel Secure Network Access Document status Standard Document version 01 01 Document date 28 July 2008 Copyright O 2008 Nortel Networks All Rights Reserved Sourced in Canada the United States of America and India LEGAL NOTICE While the information in this document is believed to be accurate and reliable except as otherwise expressly agreed to in writing NORTEL PROVIDES THIS DOCUMENT AS IS WITHOUT WARRANTY OR CONDITION OF ANY KIND EITHER EXPRESS OR IMPLIED The information and or products described in this document are subject to change without notice Nortel the Nortel logo and the Globemark are trademarks of Nortel Networks All other trademarks are the property of their respective owners Contents Regulatory Information and Safety Precautions 5 International Regulatory Statements of Conformity 5 National Electromagnetic Compliance EMC Statements of Compliance 5 FCC statement USA only 5 ICES statement Canada only 6 Canadian Department of Communications Radio Interference Regulations 6 R glement sur le brouillage radio lectrique du minist re des Communications 6 CE marking statement Europe only 6 EN 55022 statement 6 EN 55024 statement 6 European Union and European Free Trade Association EFTA notice 6 VCCI statement Japan Nippon only 7 MIC notice Republic of Korea only 7 National Safety Statem2. Read the information in this section to learn about regulatory conformities and compliances International Regulatory Statements of Conformity This is to certify that the Nortel Secure Network Access Switch equipment was evaluated to the international regulatory standards for electromagnetic compliance EMC and safety and were found to have met the requirements for the following international standards Electromagnetic Emissions CISPR 22 Class e EMC Electromagnetic Immunity CISPR 24 e Electrical Safety IEC 60950 with CB member national deviations Further the equipment has been certified as compliant with the national standards as detailed below National Electromagnetic Compliance EMC Statements of Compliance FCC statement USA only This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the Federal Communications Commission FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy If it is not installed and used in accordance with the instruction manual it may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case users will be required to take whatever measures ma
3. 3 Use the following device shipping accessories checklist to verify that in the shipping container includes all contents Check Accessory Use to Switch Install in a 4 post server rack Power units Connect the units to an appropriate and properly grounded power source Network cables Connect the device Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks 26 Installation L T w EEE F r r F sss sOIAIM copper network Connect the network cables interface card Console cable Establish a console connection to the device End Installing an NSNA device into a rack Install an NSNA in a standard equipment rack Prerequisites for installing an NSNA into a rack Do not install the device in the network equipment racks The following procedure describes how to rack mount the device Observe all safety and precautionary warnings in this procedure Review Safety and installation precautions before proceeding with the installation process To install the Nortel Secure Network Access Switch perform the following tasks Throughout the following procedure bold numbers in brackets are presented These correspond with the numbers in the step illustration to provide a visual reference for the installation procedure steps Procedure steps Step Action 1 Hold the left and right slide rails and
4. 2 0 28 July 2008 Copyright 2008 Nortel Networks 32 Installation I eC SSCs Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks Configuration This chapter contains configuration instructions for commissioning the Nortel Secure Network Access Switch Navigation e Creating a new cluster page 33 Joining an SNAS to an existing cluster page 36 Enabling the browser based interface page 38 e Applying the Nortel SNAS license page 40 Creating a new cluster This section describes how to create a new cluster Nortel Secure Network Access Switch Nortel SNAS is member of a cluster A cluster can consist of a single unit of a group of units that share the same configuration parameters There can be more than one cluster in the network each with its own set of parameters and services Establish a console connection by cabling the unit to a terminal or a computer running a terminal emulator session Prerequisites Establish a console connection by cabling the unit to a terminal or a computer running a terminal emulator session Procedure steps Step Acltion 1 Using the supplied console cable connect the terminal to the console port 2 Power on the terminal and the Nortel Secure Network Access Switch 4070 Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Stand
5. Host 1 apply The SNAS is now enabled to support additional authenticated user sessions End Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks Nortel Secure Network Access Installation Quick Start Switch 4070 Copyright 2008 Nortel Networks All Rights Reserved Publication NN47230 303 Document status Standard Document version 01 01 Document date 28 July 2008 To provide feedback or report a problem in this document go to http www nortel com documentfeedback Sourced in Canada the United States of America and India LEGAL NOTICE While the information in this document is believed to be accurate and reliable except as otherwise expressly agreed to in writing NORTEL PROVIDES THIS DOCUMENT AS IS WITHOUT WARRANTY OR CONDITION OF ANY KIND EITHER EXPRESS OR IMPLIED The information and or products described in this document are subject to change without notice Nortel the Nortel logo and the Globemark are trademarks of Nortel Networks All other trademarks are the property of their respective owners NORTEL
6. license The Nortel SNAS ships with support for up to 200 authenticated user sessions To support additional users on your Nortel SNAS switch you must obtain a Nortel SNA software license file The software license file contains a software license key that you must enter into the Nortel SNAS switch to activate support for the additional users The file can support an additional 100 250 500 1000 2000 or 5000 users The following table lists the part number for the additional concurrent endpoints Part Number Description EB1639171 Secure Network Access License Add 100 concurrent endpoints EB1639172 Secure Network Access License Add 250 concurrent endpoints EB1639175 Secure Network Access License Add 500 concurrent endpoints EB1639182 Secure Network Access License Add 1000 concurrent endpoints Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright O 2008 Nortel Networks Applying the Nortel SNAS license 41 Part Number Description EB1639183 Secure Network Access License Add 2000 concurrent endpoints EB1639184 Secure Network Access License Add 5000 concurrent endpoints Procedure steps Step Action 1 Contact Nortel Customer Support and purchase part number In North America Nortel Customer Support can be contacted at 1 800 4NORTEL 1 800 466 7835 For phone numbers outside of North America refer to http www nortel
7. unit must be secured with appropriate mounting brackets Mounting brackets are not designed to support multiple units Cable and connector safety Use the following instructions to safeguard cables and connectors while working with the NSNA Connect the device to a properly grounded outlet Do not overload the power outlet when multiple devices are installed in the server rack Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright O 2008 Nortel Networks Installation checklist 23 Installation checklist This checklist represents the high level tasks that must be performed to successfully install the Nortel Secure Network Access Switch Device installation involves the following steps Procedure steps Step Action 1 Choose a suitable location to install the device Use the information contained in the following sections to determine where the device should be installed e Safety and installation precautions Hardware specifications 2 Unpack the device from the shipping container Unpack all items from the original packaging and determine if all items have been shipped All items listed in Package contents should be present If items are missing contact the party from whom the Nortel Secure Network Access Switch was purchased 3 Mount the switch To rack mount the Nortel Secure Network Access Switch see the Installing the Nortel SNAS 4070 in N
8. 03 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks Creating a new cluster 35 Enter network mask 255 255 255 0 Specify the desired network mask or accept the suggested value by pressing ENTER If a connected router or switch attaches VLAN tag IDs to incoming packets specify the VLAN tag ID used 10 Setup a two armed configuration Setup two armed configuration yes no 11 Enter a default gateway address Enter default gateway IP address or blank to skip Enter a default gateway IP address that is within the same network address range as the host IP address 12 Enter a Management IP address MIP Enter the Management IP MIP address Making sure the MIP does not exist ok Trying to contact gateway ok Enter a unique Management IP address MIP that is within the same network address range as the host IP address and the default gateway IP address 13 Configure the time zone NTP and DNS server settings Configuration of NTP is optional and can be accomplished later Enter a timezone or select select Select a continent or ocean Select a country Select a region Selected timezone Enter the current date YYYY MM DD 2006 03 01 Enter the current time HH MM SS 09 26 16 Enter NTP server address or blank to skip Enter DNS server address 14 Generate new SSH host keys and define a password for the admin user Nortel Secure Network Access Installatio
9. 2008 Copyright O 2008 Nortel Networks 8 Regulatory Information and Safety Precautions Exporter Nortel Networks 4655 Great America Parkway Santa Clara CA 95054 USA Importer Nortel Networks de M xico S A de C V Avenida Insurgentes Sur 1605 Piso 30 Oficina Col San Jose Insurgentes Deleg Benito Juarez M xico D F 03900 52 5 480 2100 52 5 480 2199 Model SNAS 4070 AC Redundant Power Supply 835W Input 100 127 VAC 10 0A 200 240 VAC 5A 50 60 HZ Informaci n NOM unicamente para M xico La informaci n siguiente se proporciona en el dispositivo o en los dispositivos descritos en este documento en cumplimiento con los requisitos de la Norma Oficial M xicana NOM Exportador Nortel Networks 4655 Great America Parkway Santa Clara CA 95054 USA Importer Nortel Networks de M xico S A de C V Avenida Insurgentes Sur 1605 Piso 30 Oficina Col San Jose Insurgentes Deleg Benito Juarez M xico D F 03900 Tel 52 5 480 2100 Fax 52 5 480 2199 Embarcar a Modele SNAS 4070 AC Redundant Power Supply 835W Input 100 127 VAC 10 0A 200 240 VAC 5A 50 60 HZ Denan statement Japan Nippon only Ai RACE ATARI UA Fort lt RTT ACTF FT FRLO MMT VPM CHAS 50 9 T FRE dS ASR OD Bn s 22 LL T EAS ER e Min TEEN RO Ak e fh BR LEES TIA EATER ADO Nortel Secure Network Access Installation Quick Sta
10. 30 Installation End ATTENTION To remove the device reverse these instructions Cabling the device This section describes about cabling the device for network and console connections Cabling the device navigation e Connecting network cables page 30 Connecting serial cables page 30 Connecting network cables The Nortel Secure Network Access Switch 4070 contains copper network interface card running at Intel Dual LAN 10 100 1000 Connecting serial cables This section describes how to connect a DB9 serial cable to establish a console connection to the device Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks Cabling the device 31 Procedure steps Step Action 1 Prepare either an ASCII terminal or a computer running terminal emulation software to serve as the command device 2 Configure the terminal or computer with the following parameters Serial connection parameters Parameter Value Baud Rate 9600 Data Bits 8 Parity Stop Bits Flow Control 3 Connect one end of the serial cable to the terminal or computer 4 Connect the other end of the serial cable to the serial connector located at the rear of the device 5 Proceed with establishing the console connection End Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard
11. I For example if the device IP address is 192 168 0 3 and the designated port is 8080 the device is accessed from the browser as http 192 168 0 3 8080 From the HTTP access menu enable BBI access using the ena command gt gt HTTP ena Finalize the changes using the apply command gt gt HTTP apply Steps 8 through 11 provide instruction on enabling HTTPS access to the BBI Enabling HTTPS is not necessary for access to the BBI but provides a more secure environment than HTTP access Optional From the Administrative Applications menu prompt use the https command to enter HTTPS access menu Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright O 2008 Nortel Networks 40 Configuration gt gt Administrative Applications https 9 Optional From the HTTPS access menu designate a port for HTTPS access using the port command gt gt HTTPS port lt port_number gt Using a port other than 4443 requires the user to designate the port when accessing the BBI For example if the device IP address is 192 168 0 3 and the designated port is 465 the device is accessed from the browser as https 192 168 0 3 465 10 Optional From the HTTPS access menu enable BBI access using the ena command gt gt HTTPS ena 11 Optional Finalize the changes using the app1y command gt gt HTTPS apply End Applying the Nortel SNAS
12. July 2008 Copyright 2008 Nortel Networks Introduction The Nortel Secure Network Access Switch NSNA 4070 Quick Start Guide provides basic instructions about installing the hardware and performing basic configuration and management of the network The Nortel Secure Network Access Solution Nortel SNAS is a clientless solution that provides seamless secure access to the corporate network from inside or outside the network This contributes to the quality of the end user experience by allowing web based applications to operate more efficiently Prerequisites Navigation This guide is intended for network installers and system administrators engaged in the configuration and management of a network This guide assumes a familiarity with the following topics networks Ethernet bridging and IP routing networking concepts and terminology e windowing systems and graphical user interfaces GUI e network topologies e Installation preparation page 21 Installation page 25 Configuration page 33 Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks 20 Introduction 515 gt TIK TIODHUcX zum Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks Installation preparati
13. ace ip address gt This IP address should be within the same network address range as the clusters Management IP address 4 Enter the network mask Enter network mask 255 255 255 0 255 255 255 0 Specify the desired network mask or press Enter to accept the suggested value If a connected router or switch attaches VLAN tag IDs to incoming packets specify the VLAN tag ID to use 5 Press Enter to create a one armed configuration Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks 38 Configuration The system is initialized by connecting to the management server on an existing cluster which must be operational and initialized 6 Enter the Management IP address MIP of the existing cluster Enter the Management IP MIP address 10 9 254 55 Provide the Management IP address of the cluster to which you want to join the new SNAS To check the Management IP of an existing cluster connect to the cluster and use the cfg sys cur command 7 Provide the correct admin user password Enter the existing admin user password End The SNAS that is joined to the cluster automatically picks up all configuration data from an installed SNAS in the cluster Wait until the Setup utility gets finished The login prompt appears login admin Password Log in as admin to continue to configure th
14. ard 2 0 28 July 2008 Copyright 2008 Nortel Networks 34 Configuration 3 To initiate the system connection process press ENTER on the terminal 4 At the login prompt log in as user admin 5 At the password prompt enter the administrator password The default administrator password is admin ATTENTION To ensure continuing system security change the default password to the password of your choice after you successfully configure the switch 6 After password verification when the device is booted for the first time the Setup menu is displayed Use the new command to begin cluster creation Setup Menu join Join an existing iSD cluster new Initialize host as a new installation boot Boot menu info Information menu exit Exit global command always available gt gt Setup new Setup will guide you through the initial configurati on 7 Specify the network connectivity port Enter port number for the management interface 1 3 ATTENTION The Nortel SNAS 4070 has two ports for the management interface This port is assigned to Interface 1 8 Specify the host IP address Enter IP address for this machine on management interface The IP address must be unique and within the same address range as the Management IP address The host IP address is assigned to Interface 1 9 Enter network mask Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 3
15. ate measures EN 55024 statement This is to certify that the Nortel Secure Network Access Switch is shielded against the susceptibility to radio interference in accordance with the application of Council Directive 2004 108 EC Conformity is declared by the application of EN 55024 CISPR 24 European Union and European Free Trade Association EFTA notice All products labeled with the CE marking comply with R amp TTE Directive 1995 5 EEC which includes the Electromagnetic Compliance EMC Directive 2004 108 EC and the Low Voltage Directive 2006 95 EC issued by the Commission of the European Community Compliance with these directives implies conformity to the following European Norms ENs The equivalent international standards are listed in parenthesis EN 55022 CISPR 22 Electromagnetic Interference Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright O 2008 Nortel Networks NOM statement Mexico only 7 EN 55024 IEC 61000 4 2 3 4 5 6 8 11 Electromagnetic Immunity e EN 61000 3 2 IEC 610000 3 2 Power Line Harmonics EN 61000 3 3 IEC 610000 3 3 Power Line Flicker VCCI statement Japan Nippon only This is a Class A product based on the standard of the Voluntary Control Council for Interference VCCI for information technology equipment If this equipment is used in a domestic environment radio disturbance m
16. ay arise When such trouble occurs the user may be required to take corrective actions HPRAUER A SORE SERIA VCCI ORE ESC PFAARRMRECT CORRS REM CERAS 2 t BK HRSA T LEAH ST TORAL AERA eir DEJEKIEN DC ES DD SFT MIC notice Republic of Korea only This device has been approved for use in Business applications only per the Class A requirements of the Republic of Korea Ministry of Information and Communications MIC This device may not be sold for use in a non business application Observe the Regulatory Marking label on the back or bottom of each switch for specific certification information pertaining to this model Each Nortel Secure Network Access Switch model is approved for shipment to usage in Korea and is labeled as such with all appropriate text and the appropriate MIC reference number National Safety Statements of Compliance EN 60950 statement This is to certify that the Nortel Secure Network Access Switch eqipment is in compliance with the requirements of EN 60950 in accordance with the Low Voltage Directive Additional national differences for all European Union countries have been evaluated for compliance NOM statement Mexico only The following information is provided on the devices described in this document in compliance with the safety requirements of the Norma Oficial M xicana NOM Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July
17. ce 1 and lower the server onto the slide rails Ensure that each slide rail tab is inserted in the matching insert on the server and that the server is resting on the top edge of the slide rail Carefully slide the device along the slide rails approximately 2 54 centimeters 1 inch toward the server rack to lock the device on the slide rails When the device is locked in position an indicator 1 is visible on each side of the device Ensure that the device is securely attached to the slide rail hooks 2 To remove the device from the rack lift up on the indicator and slide the server forward Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks Installing an NSNA device into a rack 29 5 Lift the locking levers 1 on the slide rails and slide the device into the server rack until it extends approximately 10 16 centimeters 4 inches from the rack 6 Slide the device into the server rack cabinet until the release latches 1 lock into place To slide the device out of the rack press on the release latches Insert the included optional M6 screws in the front and rear of the device 2 if moving the server rack or the rack is installed in a vibration prone area Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks
18. com callus 2 Once this is purchased Nortel Customer Support sends a certificate that contains a unique product code and an e mail address Send this unique product code and the device MAC address to the e mail address provided The device MAC address can be obtained by using the info local command in the CLI gt gt Main info local 3 After the unique product code and device MAC address is verified a keycode is sent back to you Use this keycode to enable additional authenticated user sessions End The keycode is applied to the device through either the CLI or the BBI Perform one of the following procedures to apply the license keycode Through BBI Procedure steps Step Action 1 Click Config 2 Select Cluster gt Host gt License from the BBI menu 3 Paste the keycode in the text box labeled New License 4 Click Save Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks 42 Configuration End Through CLI Procedure steps Step Acltion 1 Enter the command cfg sys host lt host number gt license 2 Enter the keycode gt gt Main cfg sys host lt host number gt license 3 Press Enter on the keyboard to create a new line and type three periods 4 Press Enter to input the keycode 5 Use the app1y command to save the license and enable the feature gt gt Cluster
19. d a nonexclusive license to use Software only on such hardware or CFE as applicable Software contains trade secrets and Customer agrees to treat Software as confidential information using the same care and discretion Customer uses with its own similar information that it does not wish to disclose publish or disseminate Customer will ensure that anyone who uses the Software does so only in compliance with the terms of this Agreement Customer shall not a use copy modify transfer or distribute the Software except Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks 14 Software license as expressly authorized b reverse assemble reverse compile reverse engineer or otherwise translate the Software c create derivative works or modifications unless expressly authorized or d sublicense rent or lease the Software Licensors of intellectual property to Nortel Networks are beneficiaries of this provision Upon termination or breach of the license by Customer or in the event designated hardware or CFE is no longer in use Customer will promptly return the Software to Nortel Networks or certify its destruction Nortel Networks may audit by remote polling or other reasonable means to determine Customer s Software activation or usage levels If suppliers of third party software included in Software require Nortel Networks to include additional or
20. different terms Customer agrees to abide by such terms provided by Nortel Networks with respect to such third party software 2 Warranty Except as may be otherwise expressly agreed to in writing between Nortel Networks and Customer Software is provided AS IS without any warranties conditions of any kind NORTEL NETWORKS DISCLAIMS ALL WARRANTIES CONDITIONS FOR THE SOFTWARE EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND ANY WARRANTY OF NON INFRINGEMENT Nortel Networks is not obligated to provide support of any kind for the Software Some jurisdictions do not allow exclusion of implied warranties and in such event the above exclusions may not apply 3 Limitation of Remedies IN NO EVENT SHALL NORTEL NETWORKS OR ITS AGENTS OR SUPPLIERS BE LIABLE FOR ANY OF THE FOLLOWING a DAMAGES BASED ON ANY THIRD PARTY CLAIM b LOSS OF OR DAMAGE TO CUSTOMER S RECORDS FILES OR DATA OR c DIRECT INDIRECT SPECIAL INCIDENTAL PUNITIVE OR CONSEQUENTIAL DAMAGES INCLUDING LOST PROFITS OR SAVINGS WHETHER IN CONTRACT TORT OR OTHERWISE INCLUDING NEGLIGENCE ARISING OUT OF YOUR USE OF THE SOFTWARE EVEN IF NORTEL NETWORKS ITS AGENTS OR SUPPLIERS HAVE BEEN ADVISED OF THEIR POSSIBILITY The foregoing limitations of remedies also apply to any developer and or supplier of the Software Such developer and or supplier is an intended beneficiary of this Secti
21. e phase conductors 1 WARNING Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright O 2008 Nortel Networks Trademarks 11 CAUTION To reduce the risk of fire use only number 26 AWG or larger UL Listed or CSA Certified Telecommunication Line Cord for all network connections WARNING Before working on this equipment be aware of good safety practices and the hazards involved with electrical circuits Trademarks Nortel Nortel Networks the Nortel logo and the Globemark are trademarks of Nortel Networks Adobe and Adobe Reader are trademarks of Adobe Systems Incorporated Microsoft Windows and Windows NT are trademarks of Microsoft Corporation The asterisk after a name denotes a trademarked item Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks 12 Regulatory Information and Safety Precautions Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks Software license This section contains the Nortel Networks software license Nortel Networks software license agreement This Software License Agreement License Agreement is between you the end user Customer and Nortel Networks Corporation and its subsidiarie
22. e SNAS cluster using the CLI or the BBI Enabling the browser based interface The SNAS browser based interface BBI is not immediately available for use when the device is first commissioned The BBI can be enabled to work over HTTP HTTPS or both protocols It is recommended the default ports of 80 HTTP and 4443 HTTPS be changed when it comes to device management HTTP and HTTPS client traffic is connected through these default ports and if used in device management cannot be available to service requests Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright O 2008 Nortel Networks Enabling the browser based interface 39 To enable the BBI perform the following procedure Procedure steps Step Acltion 1 2 Establish a console connection or Telnet session with the device Log into the switch with an administrative user name and password From the main Command Line Interface CLI prompt enter the Administrative Applications menu with the c g sys adm command gt gt Main cfg sys adm From the Administrative Applications menu prompt use the http command to enter HTTP access menu gt gt Administrative Applications http From the HTTP access menu designate a port for HTTP access using the port command gt gt HTTPH port port number gt Using a port other than 80 requires the user to designate the port when accessing the BB
23. ents of Compliance 7 EN 60950 statement 7 NOM statement Mexico only 7 Informaci n NOM unicamente para M xico 8 Denan statement Japan Nippon only 8 National Environmental Statements of Compliance 9 Restriction on Hazardous Substances Directive Compliance Statement 9 WEEE Directive Compliance Statement 9 Notices 9 Cautions and Warnings 10 Software license 13 New in this release 17 Features 17 Other changes 17 Introduction 19 Prerequisites 19 Navigation 19 Installation preparation 21 Navigation 21 Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks 4 Contents Safety precautions 21 Safety precautions navigation 21 Installation checklist 23 Installation 25 Navigation 25 Unpacking the device 25 Installing an NSNA device into a rack 26 Prerequisites for installing an NSNA into a rack 26 Cabling the device 30 Cabling the device navigation 30 Connecting network cables 30 Connecting serial cables 30 Configuration 33 Navigation 33 Creating a new cluster 33 Prerequisites 33 Joining an SNAS to an existing cluster 36 Enabling the browser based interface 38 Applying the Nortel SNAS license 40 Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks Regulatory Information and Safety Precautions
24. inimum of 15 centimeters 6 inches of space provides proper airflow To prevent damage to server components always install a blank filler panel to cover the open space and ensure proper air circulation Install the device only in a server rack with perforated doors Plan the device installation starting from the bottom of the server rack Install the heaviest device in the bottom of the server rack Do not extend more than one device out of the server rack at the same time Remove the server rack doors and side panels to provide easier access during installation Connect the device to a properly grounded outlet Do not overload the power outlet when multiple devices are installed in the server rack Install the device in a server rack that meets the following requirements Minimum depth of 70 millimeters 2 76 inches between the front mounting flange and inside of the front door Minimum depth of 157 millimeters 6 18 inches between the rear mounting flange and inside of the rear door Minimum depth of 718 millimeters 28 27 inches and maximum depth of 762 millimeters 30 inches between the front and rear mounting flanges to support the use of the cable management arm Do not place any object directly on a server rack mounted device Server rack mounted devices are not meant to be load bearing units When mounting this device in a server rack do not stack units directly on top of one another in the rack Each
25. n Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright O 2008 Nortel Networks 36 Configuration 15 16 Generate new SSH host keys yes This may take a few seconds ok Enter a password for the admin user Re enter to confirm To maintain a high level of security while using an SSH connection accept the default choice to generate new SSH host keys If you like to go through setup Run NSNAS quick setup wizard yes nol yes Cluster creation is complete Login using the admin user to continue with configuration End Joining an SNAS to an existing cluster This section describes how to set up one armed configuration to add additional NSNA to an existing cluster by specifying the Management IP address MIP While joining SNAS to an existing cluster less information is needed because the new SNAS fetches most of the configuration from the other SNAS s in the cluster Prerequisites For the cluster configuration all the nodes must be on a same subnet If the Access list consists of entries e g IP addresses for control of Telnet and SSH access add the cluster s MIP the existing SNAS host IP address on Interface 1 and the host IP address for the new SNAS to the Access list This must be done before you join the new SNAS or the devices cannot communicate Use cfg sys accesslist to check the Access list If the Access list is empty this step is not requi
26. on This section provides basic information about the Nortel Secure Network Access Switch NSNA 4070 and the checklist of the shipped accessories Navigation e Safety precautions page 21 e Installation checklist page 23 Safety precautions This section describes the safety precautions which are vital for handling and installation of the NSNA Safety precautions navigation e Personal safety before installing the device page 21 e Module safety page 21 Cable and connector safety page 22 Personal safety before installing the device For your safety review the following personal safety warnings before working with the NSNA Two or more people must be involved in installing the device Use the following safe practices for lifting Items between 18 and 32 kilograms 39 7 and 70 5 pounds should be lifted by a minimum of two people Module safety Use the following general practices to prevent the equipment damage when working with the NSNA The device must be installed in a room where the ambient temperature is at or below 35 degrees Celsius 95 degrees Fahrenheit Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks 22 Installation preparation To promote proper air circulation ensure the device vents are not blocked or obstructed by cables panels server rack frames or other materials A m
27. on Some jurisdictions do not allow these limitations or exclusions and in such event they may not apply 4 General a If Customer is the United States Government the following paragraph shall apply All Nortel Networks Software available under this License Agreement is commercial computer software and commercial computer software documentation and in the event Software is licensed for or on behalf of the United States Government the respective rights to the software and software KU U UU u u uU u U uu u a c kogi I Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks Nortel Networks software license agreement 15 documentation are governed by Nortel Networks standard commercial license in accordance with U S Federal Regulations at 48 C F R Sections 12 212 for non DoD entities and 48 C F R 227 7202 for DoD entities b Customer may terminate the license at any time Nortel Networks may terminate the license if Customer fails to comply with the terms and conditions of this license In either event upon termination Customer must either return the Software to Nortel Networks or certify its destruction c Customer is responsible for payment of any taxes including personal property taxes resulting from Customer s use of the Software Customer agrees to comply with all applicable laws including all applicable export and impo
28. ortel Secure Network Access Installation Switch NN47230 302 The Nortel Secure Network Access Switch is intended to be installed in a 4 post server rack The device cannot be installed in a 2 post equipment rack It needs to be installed in a server rack which is a 4 post rack 4 Connect the device power units to an appropriate properly grounded power source 5 Connect network cables to the device 6 Power on the switch by depressing the power button on the front of the unit End Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright O 2008 Nortel Networks 24 Installation preparation Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks Installation This chapter contains installation instructions for the Nortel Secure Network Access Switch NSNA Navigation Unpacking the device page 25 e Installing an NSNA device into a rack page 26 e Cabling the device page 30 Unpacking the device Unpack the shipping container to ensure the device and all accessories are included and undamaged Procedure steps Step Action 1 Remove the equipment from the shipping container and place the device on antistatic material 2 Check all items for damage ATTENTION If the equipment is damaged contact your Nortel sales representative
29. red If the SNAS you are about to join contains a different software version than existing SNAS s install the preferred software version on the new SNAS before you join it or upgrade the whole cluster to the same software version as the new SNAS Use boot software cur to check the currently installed software version Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright O 2008 Nortel Networks Joining an SNAS to an existing cluster 37 Procedure steps Step Action 1 Choose join from the Setup menu to add an SNAS to an existing cluster setup Men join Join an existing cluster new Initialize host as a new installation boot Boot menu info Information menu exit Exit global command always available gt gt Setup join Application Optimizer Setup will guide you through the initial configuration 2 Specify the port to be used for network connectivity Enter port number for the management interface 1 3 This port is automatically assigned to Interface 1 This interface can be used for both management traffic coming from the private intranet and client traffic coming from the public Internet If port 1 is the management interface port for existing SNAS s Nortel recommends that you configure port 1 for the new SNAS as well 3 Enter the new SNAS host IP address Enter IP address for this machine on management interf
30. rt Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks Notices 9 National Environmental Statements of Compliance The WEEE Directive 2002 96 EC and RoHS Restriction of Hazardous Substances Directive 2002 95 EC sets collection recycling and recovery targets for various categories of electrical products and their waste Restriction on Hazardous Substances Directive Compliance Statement The Restriction on Hazardous Substances Directive RoHS 2002 95 EC which accompanies the WEEE Directive bans the use of heavy metals and brominated flame retardants in the manufacture of electrical and electronic equipment Specifically restricted materials under the RoHS Directive are Lead including solder used in PCB s Cadmium Mercury Hexavalent Chromium and Bromine Nortel declares compliance with the European Union EU RoHS Directive 2002 95 EC WEEE Directive Compliance Statement This product at end of life is subject to separate collection and treatment in the EU Member States Norway and Switzerland and therefore is marked with the symbol shown at the left Treatment applied at end of life of these products in these countries shall comply with the applicable national laws implementing Directive 2002 96 EC on Waste of Electrical and Electronic Equipment WEEB Nortel declares compliance with the European Union EU WEEE Directive 2002 96 EC Notices Notice paragraphs alert you abo
31. rt laws and regulations d Neither party may bring an action regardless of form more than two years after the cause of the action arose e The terms and conditions of this License Agreement form the complete and exclusive agreement between Customer and Nortel Networks f This License Agreement is governed by the laws of the country in which Customer acquires the Software If the Software is acquired in the United States then this License Agreement is governed by the laws of the state of New York Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks 16 Software license I s s sr su Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks New in this release The following sections detail what s new in Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 for Release 2 0 e Features page 17 Other changes page 17 Features This is the first standard release of the document Other changes None Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks 18 New in this release AAA AAA nn Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28
32. s and affiliates Nortel Networks PLEASE READ THE FOLLOWING CAREFULLY YOU MUST ACCEPT THESE LICENSE TERMS IN ORDER TO DOWNLOAD AND OR USE THE SOFTWARE USE OF THE SOFTWARE CONSTITUTES YOUR ACCEPTANCE OF THIS LICENSE AGREEMENT If you do not accept these terms and conditions return the Software unused and in the original shipping container within 30 days of purchase to obtain a credit for the full purchase price Software is owned or licensed by Nortel Networks its parent or one of its subsidiaries or affiliates and is copyrighted and licensed not sold Software consists of machine readable instructions its components data audio visual content such as images text recordings or pictures and related licensed materials including all whole or partial copies Nortel Networks grants you a license to use the Software only in the country where you acquired the Software You obtain no rights other than those granted to you under this License Agreement You are responsible for the selection of the Software and for the installation of use of and results obtained from the Software 1 Licensed Use of Software Nortel Networks grants Customer a nonexclusive license to use a copy of the Software on only one machine at any one time or to the extent of the activation or authorized usage level whichever is applicable To the extent Software is furnished for use with designated hardware or Customer furnished equipment CFE Customer is grante
33. separate them from the other device hardware Take one slide rail and push outward on the slide rail latch 1 and pull the latch back to open the slide rail 2 The latch catches to stay open Repeat the procedure for the other end of the slide rail and then again for the other slide rail provided Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright O 2008 Nortel Networks Installing an NSNA device into a rack 27 Right slide rail 2 Align the slide rail with the front mounting flange by aligning the score mark on the slide rail 1 with the score mark on the rail between the upper and lower U Push outward on the slide rail latch to close to the latch and secure the slide rail Do the same for the other front of the slide rail Align the slide rail with the rear mounting flange and close the latches for the rear of the slide rail to secure it Ensure the slide rails are securely seated on the mounting flanges When the slide rail are secure the slide rail pins protrude from the slide rails 2 a a D Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks 28 Installation 3 Extend the slide rails fully from the server rack until they lock Align the tabs on the slide rails with the matching inserts on the devi
34. ut issues that require your attention The following paragraphs describe the types of notices used in this guide CAUTION ESD ESD notices provide information about how to avoid discharge of static electricity and subsequent damage to Nortel products Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright 2008 Nortel Networks 10 Regulatory Information and Safety Precautions CAUTION Caution notices provide information about how to avoid possible service disruption or damage to Nortel products WARNING Warning notices provide information about how to avoid personal injury when working with Nortel products DANGER Danger High Voltage notices provide information about how to avoid a situation or condition that can cause serious personal injury or death from high voltage or electric shock DANGER Danger notices provide information about how to avoid a situation or condition that can cause serious personal injury or death Cautions and Warnings WARNING Installation must be performed by qualified service personnel only Read and follow all warning notices and instructions marked on the product or included in the documentation This product relies on the building s installation for overcurrent protection Ensure that a fuse or circuit breaker no larger than 120 15 U S 240 10 A international is used on th
35. y be necessary to correct the interference at their own expense Nortel Secure Network Access Installation Quick Start Switch 4070 NN47230 303 01 01 Standard 2 0 28 July 2008 Copyright O 2008 Nortel Networks 6 Regulatory Information and Safety Precautions ICES statement Canada only Canadian Department of Communications Radio Interference Regulations This digital apparatus Nortel Secure Network Access Switch does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications R glement sur le brouillage radio lectrique du minist re des Communications Cet appareil num rique le commutateur Nortel Secure Network Access Switch respecte les limites de bruits radio lectriques visant les appareils num riques de classe A prescrites dans le R glement sur le brouillage radio lectrique du minist re des Communications du Canada CE marking statement Europe only EN 55022 statement This is to certify that the Nortel Secure Network Access Switch equipment is shielded against the generation of radio interference in accordance with the application of Council Directive 2004 108 EC Conformity is declared by the application of EN 55022 Class A CISPR 22 CAUTION This device is a Class A product In a domestic environment this device can cause radio interference in which case the user may be required to take appropri
Download Pdf Manuals
Related Search