Home

Jenn-Air JGS8860BD Oven User Manual

1. 13 2006 Maytag Services 16026923 3 Important Safety Information As with all appliances there are certain rules to follow for safe operation Verify everyone who operates oven is familiar with the operations and with these precautions Use appliance only for its intended purpose as described Pay close attention to the safety sections of this manual Recognize the safety section by looking for the symbol or the word safety Recognize this symbol as a safety precaution If the information in this manual is not followed exactly a fire or explosion may result causing property damage personal injury or death Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance WHAT TO DO IF YOU SMELL GAS Extinguish any open flame Do not try to light any appliance Do not touch any electrical switch do not use any phone in your building Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions If you cannot reach your gas supplier call fire department Installation and service must be performed by an authorized installer service agency or gas supplier To avoid risk of electrical shock property damage personal injury or death verify wiring is correct if components were replaced Verify proper and complete operation of unit after servicing amp WARNING This gas ap
2. 25 Using the Oven 5 Cooling Fan 26 Baking Broiling and Roasting 6 Downdraft Blower Motor Removal Select Models 26 Connecting Range to 6 Convection Motor Removal Select Models 26 Electrical Requirements 6 Convection Element Replacement Select Models 26 EXTENSION Corde id ere e eicere 6 Bake Burner and Ignitor Removal 26 Product Safety Devices 6 Broil Burner and ignitor Removal 26 General Information Oven 26 Cooking Nomenclature 7 Regulator Removal 27 M 8 Gas Valve Removal Select Models 27 Placement of the Oven 8 Oven Light Bulb Oven Light Socket Replacement 27 Do Not Block Air Vents 8 Oven Vent Smoke Eliminator Removal 27 Location of Model 8 OvenHi Limit Thermostat Replacement 27 Model Identif
3. 9 RA E 9 9 OVEN LIGHT 2006 Maytag Services 16026923 21 Testing Procedures 4 WARNING To avoid risk of electrical shock personal injury or death disconnect power and gas to range before servicing unless testing requires power and or gas Quick Test Mode for EOC III Follow the procedure below to perform the EOC III quick test Once the control is in the quick test mode any relay may be activated in any sequence The test mode will be exited after 10 minutes of inactivity no pads pressed within 10 minutes Press the Setup pad then press the right ATM pad Press the left ATM pad then press and hold Back and Enter pads for 5 seconds to enter SERVICE menu options Press the right ATM pad to scroll to the TEST menu Press the left ATM pad to select TEST options Press the left ATM pad again to enter the Quick Test mode Press each of the following pads indicated in the table below Press Cancel or Setup pads to exit Non gt D NOTE Press and hold the applicable pad to activate the associated response Release the applicable pad to deactivate the associated response The control automatically enters the engineering mode so visual feedback of relay operations is available on the control display Any time a load is activated the cooling fan is activated When the load is deactivated the cooling fan is also deactivated Display will
4. 18 Oven Door Removal 29 Electronic Oven Control EOC 111 Warming Drawer Track Disassembly Testing Procedures 19 Select Models 29 Relay Logic for 111 21 Warming Drawer Disassembly 29 Quick Test Mode for EOC lll 22 Oven Door Disassembly 29 Oven Sensor and Meat Probe Resistances 22 Oven Door Warming Drawer Storage Drawer Description of Fault Codes for EOC ll 23 and Access Panel Disassembly Illustration 30 Disassembly Procedures Appendix A Removing and Replacing Range 24 Installation A 2 Front Side Trim Removal 24 Appendix B Cartridge Assembly Removal Select Models 24 Us and Gare aaa Manders B 2 Maintop Assembly Removal Select Models 24 Appendix C Gas Conversion Instructions Top Burner Assembly Removal Select Models 24 Model JGS8750BD C 2 Lower Burner Assembly Removal Select Models 24 Models JGS8850BD JGS8860BD C 6 Spark Module Replacement 25 Model JGS9900BD
5. Replace drawer Replacez le tiroir Vuelva a instalar el caj n 16026923 Slide range into position Installer take caution not to damage floor Do not tilt range side to side may damage end trim Introduisez la cuisini re en place Installateur N endommagez pas le sol N inclinez pas la cuisini re sur un c t au risque d endommager la garniture Deslice la estufa a su lugar definitivo Instalador tenga cuidado de no da ar el piso No incline la estufa de lado a lado se podria da ar el marco del borde Check leg position in ANTI TIP bracket V rifiez la position du pied dans la bride ANTI BASCULEMENT Verifique la posici n de la pata en el soporte ANTIVUELCO 2006 Maytag Services Appendix B The Use and Care information provided in this service manual is representative of a limited number of models Reference the customer s Use and Care literature included with the product order a copy if needed or consult Jenn Air s website for the specific model www jennair com 2006 Maytag Services 16026923 1 Use amp Care JENN AiR GAS DOWNDRAFT SLIDE IN RANGE Use amp CARE GUIDE JENN AIR 2 16026923 2006 Maytag Services Use amp Care SURFACE COOKING Low Use to simmer foods keep foods warm and melt chocolate or butter Some cooking may take place on the Low setting if the pan is covered It is possible to reduce the heat by rotating the knob toward OFF Be
6. Replace with LP gas orifice hood 1 95 black replace with 1 14 red or 1 61 no color replace with 97 green DO NOT OVERTIGHTEN Remplacez par une t te de gicleur pour GPL Noir 1 95 remplacez par rouge 1 14 Sans couleur 1 61 remplacez par vert 97 NE SERREZ PAS TROP Reemplacela con una caperuza de orificios de gas LP 1 95 negro reemplace con 1 14 rojo 0 1 61 sin color reemplace con 0 97 verde NO APRIETE DEMASIADO Turn on gas and electrical supply to product Ouvrez le gaz et l lectricit alimentant l appareil Abra el suministro de gas y conecte el suministro el ctrico al producto 2006 Maytag Services Gas Conversion Instructions JGS8750BD Low Flow Adjustment R glage bas d bit Ajuste del flujo minimo 1 8 Flat head Screwdriver Tournevis lame plate de 1 8 po Destornillador de 1 8 de cabeza plana NOTE Repeat steps 33 37 for all burners Adjust each surface burner one at a time Light burner Hold knob stem in LOW position Insert screwdriver to RMARQUE R p tez les tapes 33 37 pour tous les and turn to lowest setting Remove knob Ajustez engage screw Tenez la tige du bouton en position br leurs chaque br leur de surface un par un Allumez le LOW Introduisez le tournevis pour tourner la NOTA Repita los pasos 33 al 37 para todos br leur et r glez le au niveau le plus bas Enlevez le vis Mantenga la varilla de la perilla en el ajuste LOW los quemadores bouton Ajuste
7. For example to save lasagna press the lt JKL gt pad three times for L Press the lt ABC gt pad once for A press the STU pad once for S Continue until you ve finished the word 4 After each desired letter appears wait three seconds or e 7 1 press Enter before moving on the next letter Up to 14 letters including spaces can be used When the recipe name has been entered the last settings will be displayed for a few seconds RECIPE LIST will then be displayed to scroll through the list Press Favorites pad to exit the Favorites menu To Create a New Favorite Recipe Press Favorites pad Favorites On Off Press arrow key to scroll through selections 2 2 3 4 Enter the name using the keypads Select CREATE NEW with touchpad on left For example to save lasagna press the lt JKL gt pad three times for L Press the lt ABC gt pad once for A press the lt STU gt pad once for S Continue until you ve finished the word After each desired letter wait three seconds until an underline appears in the next space or press Enter pad before moving on the next letter Mb ice Favorites Up to 14 letters including spaces can be used 3 Enter the name using the keypads On Of 2006 Maytag Services 16026923 B 13 Use amp Care 5 Select ENTER to save name 6 Select cooking mode such as BAKE CONVECT BAKE CONVECT ROAST etc 7 Select
8. Remove broil burner screw Enlevez la vis du br leur Slip the broil burner off the broil orifice hood Sortez le Remove 52 natural broil orifice hood Retirez la t te de gril Retire el tornillo del quemador de asar br leur de gril de la t te du gicleur de gril Deslice el du gicleur de gril n 52 pour gaz naturel Retire la quemador de asar para sacarlo de la caperuza del caperuza del orificio de gas natural 52 del quemador orificio de asar O 2006 Maytag Services 16026923 3 Gas Conversion Instructions JGS8750BD Install green 0430 LP broil orifice hood 4 5 turns DO NOT OVERTIGHTEN Installez la t te du gicleur de gril verte 0430 pour GPL 4 5 tours NE SERREZ PAS TROP Instale la caperuza verde de 0 0430 para gas LP del orificio del quemador de asar 4 a 5 vueltas NO APRIETE DEMASIADO Place the broil burner on the broil orifice hood CAUTION Carefully insert burner pin in oven back Mettez le br leur de gril sur la t te du gicleur de gril ATTENTION Ins rez soigneusement le tenon du br leur dans le four Coloque el quemador de asar en la caperuza del orificio PRECAUCION Inserte cuidadosamente el pasador en la parte trasera del horno Reposition the broiler burner and tighten screw Re assemble oven See steps 2 4 Remettez en place le br leur de gril et serrez la vis Remontez le four Voyez les tapes 2 4 Vuelva a colocar ei quemador de asar en su lugar y apriete el t
9. V wer from unit 3 Remove screws securing bottom rear access panel to Power rom 2 Locate tabs on bottom of smoke eliminator and turn counterclockwise to release locking ears 4 Remove screws securing top rear access panel to 207 9 chassis 3 Gently pull smoke eliminator down and align locking ears with notches in oven cavity to remove Disconnect tubing from gas valve ei 9 9 4 Reverse procedure to reinstall smoke eliminator 5 6 Disconnect and label wire terminals from gas valve 7 Remove screws securing gas valve to chassis 8 Reverse procedures to reassemble Oven Hi Limit Thermostat Replacement NOTE Perform gas leak test 1 Remove maintop assembly see Maintop Assembly Removal procedure 2 Remove screws securing hi limit thermostat to oven Oven Light Bulb Oven Light Socket chassis Replacement 3 Label and remove wire terminals The light automatically illuminates when the door is 4 Reverse procedure to reinstall hi limit thermostat opened The light will not operate during a clean cycle 1 Remove power from unit 2 Open oven door and locate oven light 3 Grasp lens cover and pull outward on one side to Y gain access to the bulb SS celi I Hi Limit 4 Carefully remove old bulb by lifting bulb straight out of base 5 When installing the new bulb place cover over socket so the cut out in the glass cover aligns with the base on the socket Switch Thermostat N
10. Clean as needed 5 Natural 10 LP propane Clean as needed Gas supplied 2006 Maytag Services Testing Procedures 4 WARNING To avoid risk of electrical shock personal injury or death disconnect power and gas to range before servicing unless testing requires power and or gas Component Test Procedure Results Orifice holder Verify gas pressure 5 Natural dual ring burner 10 LP propane 12 K btu Check orifice for debris Clean as needed Dual ring burner valve Verify gas is supplied Gas supplied DIAL LAYOUT Orifices adjusted for Natural or LP Test Procedure Switch membrane assembly Closed circuitry resistance defined as continuity 2000 Max Q NOTE To avoid equipment Pins 1 amp 8 are shorted together for control damage use caution when configuration purposes checking electronic control circuitry ao Measurement Continuity Continuity Continuity Continuity Continuity Continuity Latch pac lE Continuity Detail B Favorites Continuity More Options Continuity Setup Continuity ATM 1 Continuity ATM2 Continuity Back Continuity Enter Continuity Timer 1 Continuity Timer 2 Continuity Oven Light Continuity Switch membrane assembly Closed circuitry resistance Measurement defined as continuity 2000 Max Q Continuity NOTE To avoid equipment Pins 1 amp 7 are shorted together for control 2 Continuity damage use caution when configuration purposes Continuity checking electron
11. 10 Gently lift main top away from chassis 11 Reverse procedure to reinstall maintop assembly Top Burner Assembly Removal Select Models 1 Disconnect power before servicing 2 Remove screws securing burner top assembly to lower assembly 3 Label and remove wire terminals to ignitor 4 Reverse procedures to reassemble Lower Burner Assembly Removal Select Models 1 Remove top burner see Top Burner Assembly Removal Select Models procedure 2 Disconnect tubing from lower assembly 3 Reverse procedures to reassemble NOTE Perform gas leak test 2006 Maytag Services Disassembly Procedures To avoid risk of electrical shock personal injury or A CAUTION death disconnect power and gas before servicing unless testing requires power and or gas Spark Module Replacement Burner Switch Replacement 1 Remove unit from installation position see 1 Remove control panel see Control Panel Assembly Removing and Replacing Range procedure Removal procedure 2 Remove screws securing rear access panel 2 Disengage burner switch from burner valve and 3 Disconnect and label wire connections from the spark remove switch from valve module 3 Reverse procedure to reinstall burner switch 4 Remove screws securing spark module to unit chassis ZO 5 Replace and reverse procedure to reassemble AR Oven Sensor Manifold Assembly Removal Sy Cooling 1 Remove maintop see Maintop Assembly Removal proced
12. 9d21 Latch will not unlock Check wire connections If OK replace motorized door lock 9d31 Latch both locked and unlocked Check wire connections If OK replace motorized door lock 2006 Maytag Services 16026923 13 Troubleshooting Procedures WARNING To avoid risk of electrical shock personal injury or death disconnect power and gas to range before servicing unless testing requires power and or gas Oven Sensor Meat Probe and Cooling Fan Temperature Charts OVEN SENSOR Sensor Type RTD 1000 Q platinum Calibration 1654 350 F 177 C Temperature F C Resistance Ohms 100 38 1143 200 94 1350 300 149 1553 350 177 1654 400 204 1753 500 260 1949 600 316 2142 700 371 2331 800 427 2516 900 483 2697 1000 538 2874 MEAT PROBE Type NTC Thermistor Calibration 9938 Q 150 F 65 5 C Temperature F C Resistance Ohms 32 0 163300 68 20 62450 95 35 32660 122 50 18020 158 70 8760 185 85 5360 212 100 3400 COOLING FAN TEMPERATURES MODE FAN ON TEMP F C FAN OFF TEMP F C Bake 350 177 300 149 Six 6 minute delay Broil after cycle started 70 1100 Six 6 minute delay Clean after cycle started 2290100 14 16026923 2006 Maytag Services Testing Procedures 4 WARNING To avoid risk of electrical shock personal injury or d
13. Abra el suministro de gas y conecte NOTA Cuando revierta una conversi n de gas el suministro el ctrico al producto LP para usar gas natural DEBE retirar el obturador de gas LP en el paso 32 Replace burner caps Replace grates Remettez les chapeaux de br leur Remettez les grilles Vuelva a instalar las tapas de los quemadores Vuelva a instalar las rejillas Low Flow Adjustment R glage bas d bit Ajuste del flujo minimo 1 8 Flat head Screwdriver Tournevis lame plate de 1 8 po Destornillador de 1 8 de cabeza plana NOTE Repeat steps 37 39 for single burners Adjust each single surface burner one at a time Light Hold knob stem in LOW position Insert screwdriver to REMARQUE R p tez les tapes 37 39 pour les burner and turn to lowest setting Remove knob engage screw Tenez la tige du bouton en position br leurs simples NOTA Repita los pasos 37 a 39 para Ajustez chaque br leur de surface simple un par un LOW Introduisez le tournevis pour tourner la los quemadores sencillos Allumez le br leur et r glez le au niveau le plus bas vis Mantenga la varilla de la perilla en el ajuste LOW Retirez le bouton Ajuste los quemadores superiores Bajo Inserte el destornillador en el tornillo sencillos uno a la vez Encienda el quemador y aj stelo al nivel m sbajo Retire la perilla 10 16026923 2006 Maytag Services Gas Conversion Instructions JGS8850BD JGS8860BD Adjust flame height
14. Convect Continuity Clean Continuity Detail B Favorites Continuity Rapid Preheat Continuity Warming Drawer Continuity More Options Continuity Setup Continuity ATM 1 Continuity ATM 2 Continuity Back Continuity Enter Continuity Timer 1 Continuity Timer 2 Continuity Oven Light Continuity Switch membrane assembly Closed circuitry resistance Measurement defined as continuity 2000 Max Q Continuity NOTE To avoid equipment Pins 1 amp 10 are shorted together for control 2 Continuity damage use caution when configuration purposes Continuity checking electronic control Continuity circuitry Continuity Continuity JGS9900B D Latch Continuity ce 1 See Detail B Continuity Continuity Continuity Cancel Continuity Bake Continuity Broil Continuity Convect Continuity Clean Continuity Detail B Favorites Continuity Rapid Preheat Continuity Vent Fan Continuity More Options Continuity Setup Continuity ATM 1 Continuity ATM 2 Continuity Back Continuity Enter Continuity Timer 1 Continuity Timer 2 Continuity Oven Light Continuity 0 o j go 2 amp 2 8 58 0 2 aN la uU 2 o J O O1 PB ffo goo Bui Ly to jo tu ii dote COOLING FAN TEMPERATURES MODE FAN ON TEMP F C FAN OFF TEMP F C Bake 350 177 300 149 Six 6 minute dela ia cb stated SUDO Six 6 minute delay after cycle started Broil Clean 225
15. 107 18 16026923 2006 Maytag Services Testing Procedures 4 WARNING To avoid risk of electrical shock personal injury or death disconnect power and gas to range before servicing unless testing requires power and or gas Electronic Oven Control EOC Ill Testing Procedures Efo do kui EN PADS ELECTRONIC OVEN CONTROL Ill TESTING PROGRAMMING PROCEDURES Feature Access Procedure Modification Procedure Control Reset Press the Setup pad then press the right Press and hold the Back and Enter pads for 5 Resets control to factory default ATM pad until SERVICE displays Press seconds to enter SERVICE menu options Press values the left ATM pad to select SERVICE menu the right ATM pad to scroll to CONTROL RESET options Press the left ATM pad to select CONTROL RESET then press the left ATM pad again to reset the control logic Press Setup to exit Oven Temperature Adjustment Press the Setup pad then press the right Enter the offset temperature setting desired using Determines oven cavity offset ATM pad until TEMP ADJUST displays the digits pads Press the right ATM pad for temperature range from 35 F to Press the left ATM pad to select oven temperature adjustment or the left ATM pad for 35 F or 21 C to 21 C TEMP ADJUSTMENT settings temperature adjustment Press 0 to reset control back to no temperature adjustment Wait 3 seconds for the control to accep
16. 3 Sensor or Meat Probe c Control Related Error not measurable 2 Lower Oven 4 Input to Control System 9 Door Lock Control System If a fault is detected then one of the following three messages will be scrolled on the display FAULT DETECTED PRESS ENTER TO TRY AGAIN This message displays when a fault is detected while a cooking function is active Clear by pressing the Cancel keypad FEATURE NOT AVAILABLE This message displays when a fault is detected while entering data during initial programming and also when a locked out function is detected Clear by pressing any key FAULT DETECTED DISABLE POWER TO CLEAR This message displays when a runaway temperature condition is detected while the control is in idle mode Press any key to clear the message but the fault remains until the control senses a Power On reset Fault Code Chart Fault Descripti c Troubleshoot Repl Code escription omponent to Troubleshoot Replace Ensure ribbon cable is securely connected inspect ribbon cable and 1 1 Shorted key connector shorts breakage corrosion etc If OK replace control Ensure ribbon cable is securely connected inspect ribbon cable 1c2c Membrane keyboard disconnected connector shorts breakage corrosion etc If OK replace control 1 4 Board to Board communication failure R
17. DO NOT OPERATE SYSTEM WITHOUT FILTER Filter should always be placed at an angle As you face the front of the range the top of the filter should rest against the left side of the vent opening The bottom should rest against the right side of the vent chamber at the bottom Important If filter is flat against the fan wall ventilation effectiveness is reduced Ventilation Chamber This area which houses the filter should be cleaned in the event of spills or whenever it becomes coated with a film of grease It can be cleaned with paper towel damp cloth or sponge and mild household detergent or cleanser Important The oven vent is located under the right side of the air grille When using or cleaning the oven hot and moist air may be noticed in this area The area near the vent may become hot enough to cause burns Be careful not to spill anything into this vent The air grille must be removed before the self clean cycle Use amp Care Oven COOKING Control Panel a 01 Bala r Favorites 1 2 3 On Off TIMERI TIMER2 ABC DEF On Off On Off Setup __ Broil On Off 4 2 e Convect Clean C C 2 8 a Rapid More Back 0 Enter Preheat Options Vent O spac done Light 4 13 KL M N The control panel is designed for ease in programming The display window shows options for each function moves from step to step through the
18. Instructions Instructions de conversion au GPL Instrucciones de conversi n a gas LP propano Only qualified personnel should convert this range Seul un personnel qualifi doit proc der a la conversion de cette cuisini re La estufa s lo debe ser convertida por personal calificado Retain natural orifices for future conversion Conservez les gicleurs pour gaz naturel pour une conversion ult rieure Guarde los orificios de gas natural para una conversi n futura Reverse this procedure for LP to natural conversion Proc dez inversement pour la conversion du GPL au gaz naturel Invierta este procedimiento para convertir el producto de gas LP a gas natural Remove oven rack Retirez la grille du four Retire la Open oven door to the first stop position Ouvrez la parrilla del horno porte du four jusqu la premi re position d arr t Abra la puerta del horno hasta el primer tope Remove oven door by holding both sides and pulling up Move hinges to the closed position Placez les Remove oven bottom screws Retirez les vis de la sole Retirez la porte du four en la tenant par les deux c t s charni res la position ferm e Mueva las bisagras a du four Retire los tornillos inferiores del horno et en la tirant vers le haut Retire la puerta del horno la posici n cerrada sosteniendo ambos lados y tirando de ella hacia arriba Note Your range may not be equipped with some of the features referred to in this manual R
19. Quickset pads 4 Press the Setup pad to exit Energy Saver To save energy the display can be set go dark if it is not being used To set the Energy Saver feature 1 Press Setup pad Setup On Off Use the arrow to scroll NO Select ENERGY SAVER Select ON or OFF using the Quickset pads 0 N Press the Setup pad to exit Press any pad to wake up the display Service This area of the oven control displays the Jenn Air Customer Service toll free phone number Setup On Off 1 Press Setup pad 2 Use the arrow to scroll 3 Select SERVICE 4 Press the Setup pad to exit Demo When Demo is selected you will see a short presentation highlighting the features of your new Jenn Air range 1 Press Setup pad Setup 2 Usethe arrow to scroll 3 Select DEMO 4 Select or OFF using the Quickset pads 5 Press the Setup pad to exit 2006 Maytag Services Appendix C 2006 Maytag Services 16026923 Gas Conversion Instructions JGS8750BD This range is equipped with fixed orifices on all burners and a convertible appliance regulator The unit serial plate States which gas it was adjusted for at the factory To convert the unit to either Natural gas or LP gas will require replacement of the oven orifice hoods and the top burner orifice hoods and adjustment of the oven burner shutters and the appliance pressure regulator con
20. Remove screws securing fan to range chassis 6 Reverse procedure to reinstall cooling fan Downdraft Blower Motor Removal Select Models 1 Remove power from unit 2 Remove bottom access panel see Bottom Access Panel Removal procedure 3 Disconnect ducting to allow for downdraft blower motor removal Label and disconnect wire terminals Remove screws securing motor assembly Reverse procedure to reinstall downdraft blower motor select models Downdraft blower motor assembly Convection Motor Removal Select Models 1 Remove power from unit 2 Open oven door and remove rack s 3 Remove screws securing convection element and fan cover on rear wall of oven cavity Remove screw securing fan blade to fan motor shaft Remove screws securing fan motor to cavity wall Slide motor into oven cavity Label and disconnect wire terminals from motor Reverse procedure to reinstall convection motor Convection Element Replacement Select Models 1 Remove power from unit 2 Open oven door and remove rack s 26 16026923 3 Remove screws securing convection element and fan cover on rear wall of oven cavity 4 Remove screw securing convection element to rear oven cavity wall 5 Label and disconnect wire terminals from element 6 Reverse procedure to reinstall convection element Bake Burner and Ignitor Removal Turn off electrical power and gas to the range Disconnect gas
21. Well Done Whole Breast Medium Well Done Ham Precooked Chicken Turkey Pork FAVORITES Favorites Favorites stores the oven mode cook time and temperature for up to 10 of your favorite recipes Convection ovens come with five preprogrammed recipes To select a recipe from the preset Recipe List 1 Press Favorites pad 2 Select RECIPE LIST Favorites 3 Select desired recipe on screen or press On Off arrow key to scroll to the desired recipe 25s d ES 4 Once the recipe is selected oven will begin preheating to the set program You may press the More Options pad to add COOK HOLD or DELAY 5 When finished press the CANCEL pad and remove food from the oven To Save the Last Recipe Completed Bake Convect Bake Convect Roast Broil Keep Warm 1 Press Favorites pad Notes The probe must be removed from the oven when it is not being used Because of the excellent insulation of the oven the retained heat continues to cook the food after the beep has sounded and the oven has turned off For this reason it is important to remove the food from the oven as soon as the beep sounds Use the handle of the probe for inserting or removing Do not pull on the cable The probe is hot after cooking use a potholder or oven mitt to remove To clean cooled probe wipe with a soapy dishcloth Do not submerge probe in water or wash in dishwasher
22. chime Determines the number and pad until TONES displays Press the left ATM every 30 seconds after the initial 4 chimes or duration of cook time reminder pad Press the left ATM pad again to select press the right ATM pad to scroll to 1 60 1 chimes COOK TONES settings chime every 60 seconds after the initial 4 chimes or 1 BEEP no additional chimes after the initial 4 chimes Press the left ATM pad to select the desired setting Press Setup to exit Timers Tones Press the Setup pad then press the right ATM Press the left ATM pad to select 2 30 or 2 Determines the number and pad until TONES displays Press the left ATM chimes every 30 seconds for up to 5 minutes duration of timer reminder pad Press the right ATM pad to scroll to after the initial chime or press the right ATM chimes TIMERS TONES Press the left ATM pad to pad to scroll to 2 60 or 2 chimes every 60 select TIMERS TONES settings seconds for up to 30 minutes after the initial chime or 1 BEEP no additional chimes after the initial chime Press the left ATM pad to select the desired setting Press Setup to exit Volume Press the Setup pad then press the right ATM Press the right ATM pad until VOLUME displays Determines volumes of cook pad until TONES displays Press the left ATM Press the left ATM pad Press the left ATM pad and timer tones pad to select VOLUME settings to select HIGH or the right ATM pad to scroll to MEDIUM or LOW Press
23. convect Press Convection Bake and Pastry Press the left ATM pad to select AUTO Setup to exit temperatures by 25 F 3 9 C CONVECT settings 208 240 V Setting Press the Setup pad then press the right Press the left ATM pad to select 208 VAC or the Determines range operating ATM pad until 208 240 displays Press the right ATM pad to select 240 VAC Press Setup to voltage 208 or 240 VAC left ATM pad to select 208 240 V settings exit 2006 Maytag Services 16026923 19 Testing Procedures 4 WARNING To avoid risk of electrical shock personal injury or death disconnect power and gas to range before servicing unless testing requires power and or gas Feature Access Procedure Modification Procedure Tone Options Press the Setup pad then press the right ATM Press the right ATM pad to scroll to the desired Determines cook tones timer pad until TONES displays Press the left ATM tone to modify Press Setup to exit tones and volume settings pad to select TONES options 12 Hour Shutoff Press the Setup pad then press the right ATM Press the left ATM pad to turn on 12 hour Disables 12 hour shutoff pad until 12HR SHUTOFF displays Press the shutoff or the right ATM pad to turn off 12 hour allowing the oven to operate left ATM pad to select 12 HOUR SHUTOFF shutoff Press Setup to exit indefinitely settings Cook Tones Press the Setup pad then press the right ATM Press the left ATM pad to select 1 30 1
24. door Replacez la porte du four Close oven door Complete Fermez la porte du four charni res a la premi re position d arr t Mueva las Nuelva a instalar la puerta del horno Termin Cierre la puerta del horno Completo bisagras al primer tope C 12 16026923 2006 Maytag Services Gas Conversion Instructions JGS9900BD This range is equipped with fixed orifices on all bumers and a convertible appliance regulator The unit serial plate Rev 2 1 06 Gas Downdraft Part No 8101P725 60 states which gas it was adjusted for at the factory To convert the unit to either Natural gas or LP gas will require and the appliance pressure regulator converter cap signal tique de cet appareil indique le r glage fait l usine pour un certain gaz La conversion de l appareil au replacement of the oven orifice hoods and the top burner orifice hoods and adjustment of the oven burner shutters Cette cuisini re est quip e de gicleurs fixes sur tous les br leurs et d un d tendeur convertible La plaque ro p a n e gaz naturel ou au GPL n cessite le remplacement des t tes de gicleur du four et des t tes de gicleur du br leur m sup rieur ainsi que le r glage des obturateurs de br leur du four et du capuchon du convertisseur du d tendeur Esta estufa viene equipada con orificios fijos en todos los quemadores y con un regulador convertible para electrodom sticos La placa de serie de la unidad indica para qu tipo de gas se calibr
25. en la f brica Para convertir la unidad a gas natural o a gas LP es necesario reemplazar las caperuzas de los orificios del horno y los orificios de los quemadores superiores adem s de ajustar los obturadores del quemador del horno y la tapa del convertidor del regulador de presi n del electrodom stico Inlet pressure to the appliance pressure regulator should be as follows for both operation and checking of Instructions appliance pressure regulator setting La pression d arriv e au d tendeur de l appareil doit tre la suivante pour le fonctionnement et la verification du r glage du d tendeur La presi n de entrada al regulador de presi n debe Instructions de conve rsi on au G PL ser la siguiente tanto para el funcionamiento normal como para verificar el ajuste del regulador de presi n Inlet Pressure in inches of water column Pression d arriv e en pouces la colonne d eau Presi n de entrada en pulgadas c d a Max Max M x Min Min M n Turn off gas and electrical supply to product Fermez le gaz et coupez l lectricit alimentant l appareil Cierre el suministro de gas y desconecte el suministro el ctrico al producto Pe Instrucciones de conversi n a gas LP propano Gaz naturel GPL Only qualified personnel should convert this range Seul un personnel qualifi doit proc der la Gas natural Gas LP conversion de cette cuisini re La estufa s lo debe ser convertida por
26. indicate the following Pad Response BARE hcm rete i repete Bake relay activated Broil relay activated CONVEG T rte ctr dne Convection Bake and Cooling Fan relays activated OVEN LIGHT eem Oven light relay activated RAPID PREHEAT Convection Fan HIGH LOW activated WARMING ZONE Warming Zone relay activated VENT DOWNDRAFT FAN Vent Fan relay activated CLEAN iret r ates Motorized Door Lock relay activated SETUP en orte 1 Second Beep IRURE Downdraft Fan HIGH LOW relay activated WARMING DRAWER Warming Drawer HIGH LOW relay activated Oven Sensor and Meat Probe Resistances OVEN SENSOR MEAT PROBE Sensor Type RTD 1000 O platinum Type NTC Thermistor Calibration 1654 350 F 177 C Calibration 9938 O 150 F 65 5 C Temperature F C Resistance Ohms Temperature F C Resistance Ohms 200 94 1350 32 0 163300 350 177 1654 68 20 62450 550 287 2047 95 35 32660 900 483 2697 122 50 18020 158 70 8760 185 85 5360 212 100 3400 22 16026923 2006 Maytag Services Testing Procedures 4 WARNING To avoid risk of electrical shock personal injury or death disconnect power and gas to range before servicing unless testing requires power and or gas Description of Fault Codes f
27. personal calificado Retain natural orifices for future conversion Conservez les gicleurs pour gaz naturel pour une conversion ult rieure 14 36 cm 14 36 cm Guarde los orificios de gas natural para una conversi n futura Reverse this procedure for LP to natural 6 16 cm 11 28 cm conversion Proc dez inversement pour la conversion du GPL au gaz naturel Invierta este procedimiento para convertir el producto de gas LP a gas natural SZ 2 Remove oven rack Retirez la grille du Open oven door to the first stop position four Retire la parrilla del horno Ouvrez la porte du four jusqu la premi re position d arr t Abra la puerta del horno hasta el primer tope Remove oven door by holding both sides and pulling up Retirez la porte du four en la tenant par les deux c t s et en la tirant vers le haut Retire la puerta del horno sosteniendo ambos lados y tirando de ella hacia arriba Remove oven baffle Enlevez le d flecteur de four Retire el deflector del horno 2006 Maytag Services Move hinges to the closed position Placez les Remove oven bottom Retirez la sole du four charni res la position de fermeture Retire el fondo del horno Mueva las bisagras a la posici n cerrada Caution Burner igniter is fragile Attention L allumeur de br leur est fragile Precauci n El encendedor del quemador es fr gil Remove oven burner Retirez le br leur du Remove c
28. personal injury Wear proper apparel Loose fitting or hanging garments should never be worn when using oven Flammable material could ignite if brought in contact with flame or hot oven surfaces which may cause severe burns Never use range for warming or heating a room This may cause burns injuries or a fire Do not use water on grease fires Do not let grease or other flammable materials collect in or around range Do not repair or replace any part of range unless it is recommended in this manual Use only dry potholders Moist or damp potholders used on hot surfaces may result in a burn from steam Do not let a potholder touch the flame Do not use a towel or a bulky cloth as a potholder Never leave range unattended while cooking Boilovers can cause smoking and may ignite Only certain types of glass ceramic earthenware or other glazed utensils are suitable for oven use Unsuitable utensils may break due to sudden temperature change Use care when opening oven door Let hot air or steam escape before removing or replacing food Do not heat unopened food containers in oven Build up of pressure may cause a container to burst and result in injury Keep range vent ducts unobstructed Place oven racks in desired location while oven is cool If a rack must be moved while oven is hot use a dry potholder Do not use aluminum foil to line oven bottom or racks Aluminum foil can cause a fire will seriously affect baking resul
29. range gas shut off valve and how to shut it off Authorized servicer must install the range in accordance with the Installation Instructions Adjustments and service should be performed only by authorized servicer Plug range into a 120 volt grounded outlet only Do not remove round grounding prong from the plug If in doubt about grounding of the home electrical system it is consumers responsibility and obligation to have an ungrounded outlet replaced with a properly grounded three prong outlet in accordance with the National Electrical Code Do not use an extension cord with this appliance Insure all packing materials are removed from the range before operating it to prevent fire or smoke damage should the packing material ignite Ensure range is correctly adjusted by a qualified service technician or installer for the type of gas Natural or LP Some ranges can be converted for use with Natural or LP gas With prolonged use of a range high floor temperatures could result Many floor coverings will not be able to withstand this kind of use Never install range over vinyl tile or linoleum that cannot withstand high temperatures Never install range directly over carpeting Using the Oven Donotleave children alone or unattended where a range is hot or in operation They could be seriously burned 2006 Maytag Services Do not allow anyone to climb stand or hang on the door They could damage the range and cause severe
30. sure flame is stable Surface Controls If flame should go out during a cooking operation and the burner does not reignite itself turn the burner off If a strong gas odor is detected open a window and wait five minutes before relighting the burner Be sure all surface controls are set in the OFF position prior to supplying gas to the range NEVER touch cooktop until it has cooled Expect some parts of the cooktop especially around the burners to become warm or hot during cooking Use potholders to protect hands Pilotless Ignition Pilotless ignition eliminates the need for a constant standing pilot light Each surface burner has a spark ignitor Use care when cleaning around the surface burner BURNER CAP If the surface burner does not light check if ignitor is broken soiled or wet Ignitor BURNER BASE Surface Control Knobs Use to turn on the surface burners An infinite choice of heat settings is available from Low to High At the High setting a detent or notch may be felt The knobs can be set on or between any of the settings Foron 2006 Maytag Services Graphics next to the knob identify which burner the knob controls For example the graphic at left shows the right front burner location 16026923 High Use to bring liquid to a boil or reach pressure in a pressure cooker Always reduce setting to a lower heat when liquids begin to boil or foods begin to cook An intermedi
31. temperature can be set from 170 F to 550 F in 5 increments After three seconds the oven will begin to preheat BAKE and PREHEAT will appear in the display along with 100 or the actual oven temperature whichever is higher The temperature in the display will increase in 1 increments until the oven reaches the preset temperature Allow about 15 minutes for the oven to preheat When the oven is preheated the oven will beep and PREHEAT will no longer be displayed 3 At the end of cooking turn the oven off by pressing the CANCEL pad Remove food from the oven The oven will continue operating until the CANCEL pad is pressed Notes If more than thirty seconds elapse between pressing a pad and pressing a number pad the display will return to the previous display Whenever the temperature appears in the display the oven is heating To change the oven temperature during cooking press the Bake pad and select a displayed temperature or use the number pads to enter the desired temperature The oven will automatically shut off after 12 hours if it is accidentally left on To set a Sabbath Mode see Sabbath Mode page 25 Bake Options Cook amp Hold and Delay options are available when baking When using the Cook amp Hold option the oven begins to heat immediately after the control has been set Then the oven cooks for a specified length of time When that time has elapsed the oven will automa
32. the left ATM pad to select Press Setup to exit Energy Saver Mode Press the Setup pad then press the right ATM Press the left ATM pad to enter the energy saver Enables a 1 watt standby pad until ENERGY SAVER displays Press mode or the right ATM pad to exit the energy feature If no pad is pressed the left ATM pad to select ENERGY SAVER saver mode within 5 minutes the control mode settings enters into a sleep mode Demo Mode Press the Setup pad then press the right ATM Press the left ATM pad to enable the DEMO Enables a 1 watt standby pad until DEMO displays Press the left ATM mode or the right ATM pad to exit the DEMO feature If no pad is pressed pad to select DEMO mode settings mode Once the DEMO mode begins press any within 5 minutes the control key to exit Press Setup to exit also enters into a sleep mode Service Mode Press the Setup pad then press the right ATM Press and hold the Back and Enter pads for 5 Enables access to service pad until SERVICE displays Press the left seconds to enter SERVICE menu options Press menus ATM pad to select SERVICE menu options Setup to exit Test Access Press the Setup pad then press the right ATM Press and hold the Back and Enter pads for 5 Enables access to service pad until SERVICE displays Press the left seconds to enter SERVICE menu options Press menus ATM pad to select SERVICE menu options the right ATM pad to scroll to TEST menu Press the left ATM pad to select T
33. the oven temperature using the Quickset pads OR Enter the desired temperature using the number pads 8 Add Cook Hold by selecting YES or omit Cook Hold by selecting NO 9 If you selected YES enter cook time using the Quickset pads or the number pads 10 Add Delay by selecting YES or omit Delay by selecting NO 11 If you selected YES enter the delay time by using the Quickset pads or the number pads 12 The control will display programmed settings then return to the Favorites menu 13 Press Favorites pad to exit the Favorites menu To Edit a Saved Recipe Favorites 1 Press Favorites pad On Off Setup Setup 1 Press the Setup pad On Off 2 Use the arrow to scroll through the Setup options 3 Select the desired option by pressing the Quickset pads Note To back out of a screen without making any changes press the Setup pad The display will return to the time of day Clock See pages 15 16 for more details Use the Clock option to Set the time of day Set day of week Select AM or PM 12 hour mode only AM or PM will not show with the time of day in the display Choose a 12 or 24 hour clock display Disable the clock display B 14 16026923 2 Press arrow key to scroll 3 Select EDIT RECIPE 4 Select desired recipe to edit You may need to press arrow key to find desired recipe 5 Follow menu to revise recipe settings as desired 6 The display will re
34. then press the right ATM pad until the right ATM pad to select 24 hour clock Press clock display on control 12 24HR displays Press the left ATM pad Setup to exit to select 12 24 HR clock Clock amp Day Display Disable Press the Setup pad then press the right Press the left ATM pad to select TIME or the right Determines if time of day and day ATM pad until DISABLE displays Press ATM pad to scroll to DAY press the left ATM pad of week will display on control the left ATM pad to select DISABLE Press the left ATM pad to enable display or the right settings ATM pad to disable display Press Setup to exit Language Display Press the Setup pad then press the right Press the right ATM pad until the desired language Determines language display on ATM pad until LANGUAGE displays displays English French Spanish Press the left control English French Press the left ATM pad to set LANGUAGE ATM pad Press Setup to exit Spanish settings C F Celsius Fahrenheit Display Press the Setup pad then press the right Press the left ATM pad to select Celsius or the right Determines temperature display on ATM pad until C F displays Press the left ATM pad to select Fahrenheit Press Setup to exit control C or F ATM pad to select C F settings Auto Convection Press the Setup pad then press the right Press the left ATM pad to turn on auto convect or When enabled reduces the ATM pad until AUTO CONVECT displays the right ATM pad to turn off auto
35. to the foreground 2 Press the TIMER pad a second time to access the edit mode in order to make changes 3 Pressing the TIMER pad a third time will cancel the Timer Changing the Timer beeps The signal beeps for TIMER 1 and TIMER 2 can be changed The options available are two beeps every thirty seconds two beeps every sixty seconds or one beep only The default setting is one beep Setup On Off 1 Press the Setup pad 2 Select the arrow to scroll until TONES is displayed 3 Select TONES 4 Select TIMERS TONES Select the desired timer beep format 2 30 SEC 2 60 SEC or 1 BEEP 6 Press Setup pad to exit Setup mode e Locking the Control and Oven Door The oven control and oven door can be locked to prevent accidental programming If an oven function is currently being used the control and door cannot be locked To lock the control and door Press the Back and Enter pads at the same time holding for three seconds or until CONTROL LOCKED appears in the display To unlock the control and door Press the Back and Enter pads at the same time holding for three seconds UNLOCKING DOOR will appear in the display when the control and door are unlocking Back 0 Enter Space lock Use amp Care Baking To set Bake 1 Press the Bake pad 2 Select the oven temperature using the Quickset pads OR Enter the desired temperature using the number pads Press Enter pad to set The
36. 00 688 9900 or visit the Web Site at www jennair com For Amana product call 1 800 843 0304 or visit the Web Site at www jennair com For product inCanada call 1 800 688 2002 Extended Service Plan We offer long term service protection for this new oven Asure Extended Service Plan is specially designed to supplement Maytag and Amana s strong warranties These plans cover parts labor and travel charges Call 1 866 232 6244 for information e Dependability Plus Extended Service Plan is specially designed to supplement Jenn Air s strong warranty This plan covers parts labor and travel charges Call 1 800 925 2020 for information 2006 Maytag Services General Information Grounding NOTE This appliance must be properly grounded for personal safety Power cord on this appliance is equipped with a three prong grounding plug This matches standard three prong grounding wall receptacle to prevent possibility of electric shock from this appliance Consumer should have wall receptacle and circuit checked by qualified electrician to verify receptacle is properly grounded It is the consumers responsibility to replace standard two prong wall receptacles with properly grounded three prong wall receptacles DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE THIRD GROUND PRONG FROM POWER CORD For 15 amp circuits only do not use an adapter on 20 amp circuit Where local codes permit a TEMPORARY CON
37. 4 JENN AIR Service This manual is to be used by qualified appliance technicians only Maytag does not assume any This Base Manual covers general information responsibility for property damage or personal Hor injury for improper service procedures done by Refer to individual Technical Sheet an unqualified person for information on specific models This manual includes but is not limited to the following Gas Sao Slide In 65888080 Range JGS9900BD 16026923 2006 Maytag Services Important Information Maytag will not be responsible for personal injury or property damage from improper service procedures Pride and workmanship go into every product to provide our customers with quality products It is possible however that during its lifetime a product may require service Products should be serviced only by a qualified service technician who is familiar with the safety procedures required in the repair and who is equipped with the proper tools parts testing instruments and the appropriate service information IT IS THE TECHNICIANS RESPONSIBLITY TO REVIEW ALL APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRS Important Notices for Servicers and Consumers 4 WARNING To avoid risk of severe personal injury or death disconnect power before servicing working on appliance to avoid electrical shock To locate an authorized servicer please consult your telephone book or the dealer from whom you p
38. 6 Maytag Services Troubleshooting Procedures WARNING To avoid risk of electrical shock personal injury or death disconnect power and gas to range before servicing unless testing requires power and or gas Troubleshooting Chart Problem Possible Cause Correction Burners will not ignite no spark at top burner Poor ground on burner Weak or failed spark module Low gas Clogged burner port e Clean burner e Replace spark module e Verify pressure 4 WCP for natural 10 WCP for LP e Clean burner cap Burner will not ignite No spark to burner ignitors when burner knob is rotated to LITE position No 120 VAC to Micro switch contacts not closing Faulty wiring Bad connection at burner electrode and electrode socket Inoperative spark module Electrode dirty Burner cap dirty Cracked or broken electrode electrode wire or electrode socket e Verify voltage at wall outlet e Check wiring against appropriate wiring diagram Verify all terminals and connections are correct and tight Check micro switch contacts e Check wiring against appropriate wiring diagram Verify all terminals and connections are correct and tight e Check module according to testing procedures information e Clean ele
39. E the cook time countdown PREHEAT BAKE and the actual oven temperature will be displayed Do not use delayed baking for highly perishable foods such as dairy products pork poultry or seafood Convect Convection uses a fan to circulate hot air evenly over under and around the food As a result foods are evenly cooked and browned often in shorter times at lower temperatures and with the flexibility of using more than one rack at a time CONVECT BAKE CONVECT ROAST Convect Options Cook amp Hold and Delay options are available when convect cooking See page 21 for information on how to program a Cook amp Hold or Delay option Multiple Rack Whole Chicken Baking of Whole Turkey Vegetables Pork Roasts Beef Roasts Tarts Tortes Cakes Cookies Biscuits Breads Casseroles 2006 Maytag Services Use amp Care Notes The oven control comes from the factory set for Auto Convect Conversion When using Convect Bake enter the conventional baking temperature The control automatically converts the temperature to 25 less than the conventional temperature When using Convect Roast the temperature will not be automatically reduced Enter the conventional roasting temperature and time The control then lets you know when 75 of the time has elapsed and alerts you to check the food for doneness To turn Auto Convect Conversion off see page 24 Convect Bake To set Convect Bake 1 Press th
40. EST options Press Setup to exit Faults Access Press the Setup pad then press the right ATM Press and hold the Back and Enter pads for 5 Displays the 10 most recent pad until SERVICE displays Press the left seconds to enter SERVICE menu options Press faults produced by the controller ATM pad to select SERVICE menu options the right ATM pad to scroll to the FAULTS menu Press the left ATM pad to select FAULTS options Press Setup to exit Software Versions Access Press the Setup pad then press the right ATM Press and hold the Back and Enter pads for 5 Displays the software and pad until SERVICE displays Press the left seconds to enter SERVICE menu options Press EEPROM revision levels ATM pad to select SERVICE menu options the right ATM pad to scroll to the VERSIONS menu Press the left ATM pad to view Press Setup to exit Display Test Press the Setup pad then press the right ATM Press and hold the Back and Enter pads for 5 Illuminates all lamps on the pad until SERVICE displays Press the left seconds to enter SERVICE menu options Press control ATM pad to select SERVICE menu options the right ATM pad to scroll to DISPLAY TEST Press the left ATM pad Press Setup to exit Control Lockout Press the Back and Setup pads Press the Back and Setup pads simultaneously Disables the touch keypad simultaneously for 5 seconds to lock for 5 seconds to unlock control and locks the oven cavity door 20 16026923 2006 Maytag Se
41. FECT THE COOKING PERFORMANCE OF THE UNIT NOTE THE FIGURE MAY NOT ACCURATELY REPRESENT YOUR RANGE COOKTOP HOWEVER THIS WARNING APPLIES TO ALL GAS COOKING PRODUCTS CE PRODUIT NE DOIT PAS TRE INSTALL SOUS UNE HOTTE D EXTRACTION QUI RENVOIE VERS LE BAS CES SYSTEMES PEUVENT ENTRAINER DES PROBLEMES D INFLAMMATION ET DE COMBUSTION AVEC LES BR LEURS A GAZ ENTRAINANT DES BLESSURES ET RISQUANT D AFFECTER LA PERFORMANCE DE CUISSON DE L APPAREIL REMARQUE LILLUSTRATION PEUT NE PAS REPR SENTER PR CIS MENT LA TABLE DE CUISSON DE VOTRE CUISINI RE CEPENDANT CET AVERTISSEMENT CONCERNE TOUS LES APPAREILS DE CUISSON GAZ ESTE PRODUCTO NO SE DEBE INSTALAR DEBAJO DE SISTEMAS DE CAMPANAS DE VENTILACI N QUE DIRIJAN EL FLUJO DE AIRE HACIA ABAJO ESTOS SISTEMAS PUEDEN CAUSAR PROBLEMAS DE ENCENDIDO Y DE COMBUSTI N DE LOS QUEMADORES LO QUE PUEDE RESULTAR EN LESIONES PERSONALES Y AFECTAR EL RENDIMIENTO DE LA COCCI N DE LA UNIDAD NOTA LA FIGURA PUEDE NO REPRESENTAR CON EXACTITUD SU CUBIERTA SIN EMBARGO ESTA ADVERTENCIA SE APLICA A TODOS LOS PRODUCTOS DE COCCI N A GAS 6 16026923 2006 Maytag Services installation Instructions If end cabinet is not present side panel kit UXA1100AA B black W white S Stainless may be ordered from dealer E NOTE For counter tops with formed front edge shave raised section to clear top REMARQUE Pour les hauts de comptoir avec un rebord avant moul raboter la sec
42. HIS APPLIANCE AND CAN RESULT IN A GAS LEAK Gas supply pressure for testing regulator must be at least 1 water column pressure above manifold pressure shown on serial plate Check Pressure of House Piping System 1 The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1 2 Ibs sq in 3 5 kPa 13 8 in water column 2 The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1 2 Ibs sq in 3 5 kPa 13 8 in water column A GAS SHUT OFF VALVE SHOULD BE PUT IN AN ACCESSIBLE LOCATION IN THE SUPPLY LINE AHEAD OF THE RANGE FOR TURNING ON AND TURNING OFF GAS SUPPLY CONNECTOR NUTS MUST NOT BE CONNECTED DIRECTLY TO PIPE THREADS THE CONNECTORS MUST BE INSTALLED WITH ADAPTORS PROVIDED WITH THE CONNECTOR The house piping and or range connector used to connect the range to the main gas supply must be clean free of metal shavings rust dirt and liquids oil or water Dirt etc in the supply lines can work its way into the range manifold and in turn cause failure of the gas valves or controls and clog burners and or pilot orifices NOTE It is recommended to use a new CSA certified 1 2 flexible connector no longer than 36 91 4 cm with a minimum BTU HR rating
43. Instrucciones de Instalaci n INSTALLER Leave these instructions with the appliance INSTALLATEUR Laissez ces instructions avec l appareil INSTALADOR Deje estas instrucciones con el electrodom stico Printed in USA 2005 Maytag Corporation Rev 0 10 05 8101P697 60 2 16026923 2006 Maytag Services 2006 Maytag Services installation Instructions Jenn Air Updraft Gas Slide In Range INSTALLATION INSTRUCTIONS PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE This manual is intended to assist in the initial installation and adjustments of the range Only qualified personnel should install or service this range Read Safety Instructions in Use amp Care book before using range Improper installation adjustment alteration service maintenance or use of range can result in serious injury or property damage Installer take care not to damage flooring CAUTIONS Do not lift or move range by grasping door handles or main top This range has been designed in accordance with the requirements of various safety agencies and complies with the maximum allowable wood cabinet temperatures of 194 If this range is installed with cabinets that have a lower working temperature than 194 F discoloration delamination or melting may occur Place range in a well lit area Do not set range over holes in the floor or other locations where it may be subject to strong drafts Any opening in the wall be
44. L SUMINISTRO DE GAS AL PRODUCTO Regulator D tendeur Shut Off Valve Robinet d arr t Valvula de cierre T 10 straight pipe Tuyau rectiligne 10 po 25 4 cm max M x 10 25 4 cm de tuber a recta D Adaptor Adaptateur Adaptador Flexible Connector Tuyau de raccordement Conector flexible Only qualified personnel should install range Must be installed in accordance with local codes See instructions in front of this manual Seul du personnel qualifi doit installer la cuisini re Elle doit tre install e selon les codes locaux Voyez les instructions au d but de ce manuel La estufa s lo debe ser instalada por personal calificado La estufa debe instalarse de acuerdo con los c digos locales Vea las instrucciones en la parte delantera de este manual Check all gas connection joints and fittings for leaks with a non corrosive leak detection fluid then wipe off V rifiez l absence de fuite tous les raccordements de gaz avec un liquide de d tection des fuites non corrosif puis essuyez le Verifique todas las conexiones y juntas del suministro de gas a la estufa usando un l quido de detecci n de escapes no corrosivo para asegurarse de que no hayan escapes Limpie el l quido cuando haya terminado Apply pipe thread compound approved for LP gas to all threads Always hold the regulator in stable position while attaching gas supply line Appliquez sur tous les filetages un compos joint
45. NECTION may be made to a properly grounded two prong wall receptacle by the use of a UL listed adapter available at most hardware stores Larger slot on adapter must be aligned with larger slot in the wall receptacle to provide proper polarity 2006 Maytag Services 16026923 amp WARNING Attaching adapter ground terminal to wall receptacle cover screw does not ground appliance unless the cover screw is metal and not insulated and wall receptacle is grounded through the house wiring Consumer should have circuit checked by a qualified electrician to verify receptacle is properly grounded When disconnecting power cord from adapter always hold adapter with one hand If this is not done adapter ground terminal is very likely to break with repeated use Should this happen DO NOT USE appliance until a proper ground has been established eutral Wire Ground Hot Line NOTE Circuit tester can be used to verify voltage at outlet Connect one lead to hot line and the other lead to ground Circuit tester should light Range Description Shut off Valve Pressure Regulator Backside of Range Burner Control Valves Electronic Control and Touchpad Bake Burner 10 Top Surface Burners and Grates Burner Control Valves lt 4 Oven Cavity p Broil Burner Convection Fan and Element Storage or Warming Drawer im Rating Label Model Number 16026923 200
46. OTE To avoid damaging the new bulb and decreasing life of the bulb do not touch new e Door Hinge bulb with bare hands or fingers Convection Fan Hold with a cloth or paper towel NOTE Proceed with the following steps for oven light socket removal 6 Remove power to unit 2006 Maytag Services 16026923 27 Disassembly Procedures 4 CAUTION To avoid risk of electrical shock personal injury or death disconnect power and gas before servicing unless testing requires power and or gas Oven Door Latch Replacement 1 Remove control panel see Control Panel Removal procedure 2 Remove screws securing door latch to the front of the oven cavity outer shell 3 Slide oven door latch assembly forward to diagnose 4 Label and disconnect wire terminals from latch assembly 5 Reverse procedure to reinstall door latch assembly Oven Door Hinge Removal 1 Remove power from unit 2 Remove unit from installation position see Removing and Replacing Range procedure 3 Remove oven door see Oven Door Removal procedure 4 Remove front side trim see Front Side Trim Removal procedure 5 Remove screws securing side panel to chassis 6 Remove the top and bottom screws securing hinge receiver to the front frame 7 Remove hinge receiver from oven chassis 8 Reverse procedure to reinstall oven door hinge Bottom Access Panel Removal Select Models 1 Grasp top of bottom access panel and gent
47. PL il est recommand de faire la conversion avant l installation L ensemble de conversion se trouve sur la tablette du d tendeur derri re le blindage Si utiliza gas LP propano se recomienda que inicie la conversion antes de realizar la instalaci n Puede encontrar el kit de instrucciones en el estante del regulador detr s del protector Cardboard Cross Support Support transversal en carton Soporte cruzado de la caja Remove drawer check Use and Care manual for directions and insure all packing cardboard cross support is removed and discarded Retirez le tiroir v rifiez le manuel d utilisation et d entretien pour les instructions et assurez vous que tout le mat riau d emballage support transversal en carton est enlev et jet Retire el caj n consulte el manual de uso y cuidado para obtener instrucciones y aseg rese de que todo el material de empaque soporte transversal de la caja de cart n sea removido y desechado Drill 1 8 3mm holes Mount ANTI TIP bracket to wall or floor with 2 screws Percez des trous de 1 8 po 3 mm Installez le support ANTIRENVERSEMENT au mur ou au sol avec deux vis Taladre agujeros de 1 8 3 mm Instale el soporte ANTIVUELCO en la pared en el piso usando 2 tornillos A 8 16026923 2006 Maytag Services 2006 Maytag Services installation Instructions TURN OFF GAS SUPPLY TO PRODUCT COUPEZ L ALIMENTATION EN GAZ DE L APPAREIL CIERRE E
48. RM Select 170 temperature Warm for 12 15 minutes To Warm Plates 12 Place two stacks of up to four plates each in the oven Press More Options pad Select KEEP WARM Select 170 temperature Warm for five minutes Turn off the oven by pressing the CANCEL pad and leave plates in the oven for 15 minutes more Use only oven safe plates check with the manufacturer Do not set warm dishes on a cold surface as rapid temperature changes could cause crazing or breakage Notes Food should be hot when placed in oven For optimal food quality foods should be kept warm for no longer than 1 hour To keep foods from drying cover loosely with foil or a glass lid Options 16026923 Meat Probe Using the probe supplied with your oven assures excellent roasting results every time 1 Insert the probe into the food item For meats the probe tip should be located in the center of the thickest part of the meat and not into the fat or touching a bone 2 Insert the probe plug into the receptacle located on the top right of the oven Be sure to insert plug into the receptacle all the way Press More Options pad 4 Press the arrow to scroll 5 Select MEAT PROBE COOK TIME 6 Set the internal food temperature desired by selecting one of the displayed temperatures or enter the temperature using the number pads The probe temperature can be set from 100 185 F If the meat probe is n
49. RTANTE Retire y pour GPL NE SERREZ PAS TROP Reempl celas con fois Retire cuidadosamente las caperuzas de los conserve las tapas usadas de los orificios de gas caperuzas de orificios de gas LP NO orificios de gas y convierta un quemador a la vez natural APRIETE DEMASIADO O 2006 Maytag Services 16026923 9 Gas Conversion Instructions JGS8850BD JGS8860BD White C Blanc tJ Blanco IMPORTANT Remove and keep old natural gas orifice Replace with LP gas orifice hoods DO NOT Replace burner heads and screws hoods IMPORTANT Retirez et conservez les anciennes OVERTIGHTEN Remplacez les avec des t tes de gicleur Hand tighten Drop in LP choke R installez les t tes t tes de gicleur pour gaz naturel IMPORTANTE Retire y pour GPL NE SERREZ PAS TROP Reempl celas con de br leur et les vis Serrez les la main Posez conserve las tapas usadas de los orificios de gas caperuzas de orificios de gas LP NO l trangleur pour GPL Vuelva a instalar las cabezas y natural APRIETE DEMASIADO los tornillos del quemador Apriete a mano Coloque el obturador de gas LP en su lugar NOTE When reversing an LP conversion back E to natural gas the LP choke in step 32 MUST Turn on gas and electrical be removed supply to product REMARQUE Lorsque vous faites une reconversion du GPL au gaz naturel Ouvrez le gaz et l lectricit h P trangleur pour GPL de l tape 32 DOIT tre alimentant l appareil retir
50. Remove storage drawer Retirez le tiroir de Remove screws from panel and then remove rangement Retire el caj n de almacenamiento panel Retirez les vis du panneau puis le panneau lui m me Retire los tornillos del panel y retire el panel Remove bake burner screws Retirez les vis du br leur de cuisson au four Retire los tornillos del quemador de horneado Swing bake burner to the side and lift bake burner off the oven orifice Pivotez le br leur de cuisson sur le c t et soulevez le pour le s parer de son gicleur Gire el quemador del horno a un lado y lev ntelo para sacarlo del orificio Locate regulator from the front Rep rez le d tendeur l avant Ubique el regulador desde la parte delantera Printed in USA 2 16026923 2005 Maytag Corporation 2006 Maytag Services Gas Conversion Instructions JGS8750BD Unscrew the regulator cap D vissez le capuchon du Remove the plastic cap Retirez le capuchon en Flip the regulator cap and replace the plastic d tendeur Desenrosque la tapa del regulador plastique Retire la tapa de pl stico cap Abattez le capuchon du d tendeur et installez le capuchon en plastique Invierta la tapa del regulador y vuelva a colocar la tapa de pl stico Screw the cap securely back into place DO NOT OVER Locate oven orifice hood from the front Identifiez la t te Remove 49 natural oven orifice hood Retirez la t te TIGHTEN Revissez bien l
51. a con orificios fijos en todos los quemadores y con un regulador convertible para electrodom sticos La placa de serie de la unidad indica para qu tipo de gas se calibro en la f brica Para convertir la unidad a gas natural o a gas LP es necesario reemplazar las caperuzas de los orificios del horno y los orificios de los quemadores superiores adem s de ajustar los obturadores del quemador del horno y la tapa del convertidor del regulador de presi n del electrodom stico Inlet pressure to the appliance pressure regulator should be as follows for both operation and checking of appliance pressure regulator setting La pression d arriv e au d tendeur de l appareil doit tre la suivante pour le fonctionnement et la v rification du r glage du d tendeur La presi n de entrada al regulador de presi n debe ser la siguiente tanto para el funcionamiento normal como para verificar el ajuste del regulador de presi n Inlet Pressure in inches of water column Natural Gas LP Gas Pression d arriv e en pouces la colonne d eau Gaz naturel GPL Presi n de entrada en pulgadas c d a Gas natural Gas LP 14 36 14 36 Min Min M n 6 16 cm 11 28 cm Turn off gas and electrical supply to product Fermez le gaz et coupez l lectricit alimentant l appareil Cierre el suministro de gas y desconecte el suministro el ctrico al producto Rev 1 1 06 Gas Updraft Part No 8101P724 60 LP Propane Conversion
52. ador y aj stelo al nivel m s bajo Retire la perilla Adjust double surface burner Light burner and turn to Adjust flame height with screwdriver Ajustez la NOTE Double burner only REMARQUE Br leur lowest setting where both inner and outer ring are lit hauteur de la flamme avec le tournevis Ajuste la double uniquement NOTA Quemador doble Remove knob Ajustez le br leur de surface double altura de la llama con el destornillador solamente Allumez le br leur et r glez le au niveau le plus bas o les deux cercles int rieur et ext rieur sont allum s Retirez le bouton Ajuste el quemador superior doble Encienda el quemador y aj stelo al nivel m s bajo en el que se encienden los anillos interior y exterior Retire la perilla CORRECT BON CORRECTO BLUE LIFTING FLAMME BLEUE SE SOULEVANT AZUL QUE SE SEPARA DEL QUEMADOR Insert screwdriver to engage screw Introduisez le Adjust flame height with screwdriver Ajustez la Verify proper flame height and appearance V rifiez tournevis pour tourner la vis Inserte el destornillador hauteur de la flamme avec le tournevis Ajuste la la taille des flammes et leur apparence Verifique la en el tornillo altura de la llama con el destornillador altura y apariencia correctas de la llama 16 16026923 2006 Maytag Services Gas Conversion Instructions JGS9900BD CORRECT BON CORRECTO YELLOW WI Open shutter to correct JAUNE Ouvrez l obturateur pour r
53. ailed gas valve Loose wire connection or broken wire e Check ignitor current draw 3 2 3 6 Amps Replace ignitor if it fails test e Check for correct gas pressure Natural gas pressure should be 5 WCP and LP gas pressure should be 10 WCP e Check gas valve for continuity e Verify all connections are clean and tight replace broken wire 2006 Maytag Services 16026923 11 Troubleshooting Procedures WARNING To avoid risk of electrical shock personal injury or death disconnect power and gas to range before servicing unless testing requires power and or gas Problem Possible Cause Correction Gas flows to bake broil burner but burner does not light Ignitor positioned too far from burner Dirt or grease in orifice or burner Insufficient gas pressure Power Reposition ignitor closer to bake broil burner Clean orifice or burner Check for correct gas pressure Natural gas pressure should be 5 WCP and LP gas pressure should be 10 WCP Verify power is present at unit Verify circuit breaker is not tripped replace fuse Broil burner shuts off shortly after the start of self clean operation Bake and broil functions operate normally Power outage Control Error Verify power is present at unit Verify circuit breaker is not t
54. an be selected 300 550 F To select a lower temperature press the appropriate number pads Press Enter pad to set the lower Notes For best results use rack position 2 or 3 when using the Rapid Preheat option 1 temperature For optimum baking and browning results Rapid Preheat is not recommended when baking on multiple racks 4 Preheat the oven for five minutes 5 Place food in the oven and close the door to the broil stop position _ _ Broil 6 Press the CANCEL pad when broiling CANCEL For optimal results preheat for five minutes with the door is done Ve ws closed and use a pan designed for broiling Oven door should be open to the broil stop position about 4 inches when broiling To set Broil Notes See Broiling Chart for foods and broiling times 1 Place the oven rack in the proper rack position see Broiling Chart f more than 30 seconds elapse between pressing the Broil pad Quickset pads or number pads the oven will not be set and the display will return to the previous display 2 Press the Broil pad Broil 3 Select HIGH 550 F for high broil HIGH is used for most broiling Use a lower broil OR temperature when broiling longer cooking foods The lower temperature allows food to cook to the well done Select LOW 450 F for low broil stage without excessive browning Expect broil times to increase and browning to be slightly lighter if the appliance is
55. and at the end of timer operation and their volume can be adjusted To adjust the beeps Setup On Off 1 Press Setup pad 2 Usethe arrow to scroll 3 3 Select TONES To change the beeps at the end of cooking 1 Follow Tones steps 1 3 see above 2 Select COOK TONE 3 Use the arrow to scroll 4 Select 1 30 MIN to hear one beep every thirty seconds OR Select 1 60 MIN to hear one beep every sixty seconds OR Select 1 BEEP to hear one beep only at the end of cooking 5 Press the Setup pad to exit To change the timer beeps 1 Follow Tones steps 1 3 see above 2 Select TIMERS TONES 3 Use the arrow to scroll 4 Select 2 30 SEC to hear two beeps every thirty seconds OR Select 2 60 SEC to hear two beeps every sixty seconds OR Select 1 BEEP to hear one beep only at the end of the set time 2 5 Press the Setup to exit Setup On Off To change the volume of the beeps 1 Follow Tones steps 1 3 see above 2 Press the arrow to scroll 3 Select VOLUME 4 Select HIGH for the highest volume OR Select MEDIUM for medium volume OR Select LOW for the lowest volume 5 Press the Setup pad to exit 12 HR Shutoff The oven will automatically turn off at the end of 12 hours if you accidentally leave it on To turn off this feature 1 Press Setup pad f Setup N 2 Use the arrow to scroll off B 16 16026923 3 Select 12HR SHUTOFF 3 Select ON or OFF using the
56. and harness If OK replace control 4d41 Cooling fan overspeed Check cooling fan motor and harness If OK replace control 4d51 Door switch circuit fault Check connections harness and motor If OK replace control 9d11 Latch will not lock Check wire connections If OK replace motorized door lock 9421 Latch will not unlock Check wire connections If OK replace motorized door lock 9d31 Latch both locked and unlocked Check wire connections If OK replace motorized door lock 2006 Maytag Services 16026923 23 Disassembly Procedures 4 CAUTION To avoid risk of electrical shock personal injury or death disconnect power and gas before servicing unless testing requires power and or gas Removing and Replacing Range 1 Turn off power and remove gas supply from unit 2 Slide range forward from installation position 8 Unplug power cord and disconnect gas line from unit 4 Disconnect downdraft blower motor and remove flex ducting to the blower and range select models NOTE To avoid countertop damage do not move range forward until range has been raised enough to clear all cabinetry 5 Pull the range forward out of the cabinet opening 6 Disconnect or unplug the power cord leading from unit to fuse box or junction box depending on unit 7 Replace the oven using the installation instructions and anti tip bracket s Front Side Trim Removal 1 Remove power from unit 2 Slide unit out far enou
57. and power from unit Remove oven door racks and oven bottom Remove screws securing bottom bake cover Raise the back of the bake burner cover and slide cover back to release the front edge of cover and lift out of oven cavity 6 Remove screws securing bake burner assembly to the oven chassis 7 Maneuver bake burner from the burner orifice and out of the slotted location 8 Pull forward on assembly to allow the ignitor terminal plug to pass through the back of the oven cavity 9 Disconnect terminal plug and remove assembly from the oven cavity 10 Remove screws securing ignitor to bake burner 11 Replace and reassemble in reverse order D Broil Burner and Ignitor Removal 1 Turn off electrical power and gas to the range 2 Disconnect gas and power from unit 3 Remove oven door and racks 4 Remove screws securing ignitor wire plate cover to back of the oven cavity 5 Maneuver ignitor wire terminal plug through the rear of the oven cavity 6 Disconnect ignitor wire terminal plug 7 Remove screws securing broiler to oven cavity 8 Carefully maneuver burner off of the broiler orifice spud and remove from cavity 9 Remove screws securing ignitor to broiler 10 Remove wing nut securing flame spreader to broiler 11 Replace and reassemble in reverse order Oven Sensor Replacement 1 Remove power from unit 2 Open oven door and remove screws securing sensor to oven cavity NOTE Genily pull wi
58. astic cap Retirez le capuchon en Flip the regulator cap and replace the plastic d tendeur Desenrosque la tapa del regulador plastique Retire la tapa de plastico cap Abattez le capuchon du d tendeur et installez le capuchon en plastique Invierta la tapa del regulador y vuelva a colocar la tapa de pl stico O 2006 Maytag Services 16026923 C 7 Gas Conversion Instructions JGS8850BD JGS8860BD Screw the cap securely back into place DO NOT OVER TIGHTEN Revissez bien le chapeau NE LE SERREZ PAS TROP FORT Enrosque la tapa firmemente en su lugar NO APRIETE DEMASIADO You MUST start bake and broil hoods by hand to avoid cross threading Vous DEVEZ faire d marrer les t tes de gicleur de cuisson et de gril la main afin d viter qu un filetage ne soit fauss Usted DEBE iniciar el enroscado de las tapas de horneado y asado a mano para evitar da ar las roscas Locate oven orifice hood from the front Identifiez la t te de gicleur du four par l avant Ubique la caperuza del orificio del quemador del horno desde la parte delantera Remove 49 natural oven orifice hood Retirez la t te de gicleur du four n 49 pour gaz naturel Retire la caperuza del orificio de gas natural 49 del horno Reverse steps 6 through 9 to reassemble oven Pour assembler nouveau le four suivez les tapes 6 9 en inversant leur ordre Invierta los pasos 6 al 9 para reensamblar el horno Install black 0512 LP
59. ate flame size is used to continue cooking Food will not cook any faster when a higher flame setting is used than needed to maintain a gentle boil Water boils at the same temperature whether boiling gently or vigorously Setting the controls The size and type of cookware will affect the heat setting 1 Place a pan on the burner grate The burner flame may lift off or appear separated from the port if a pan is not placed on the grate 2 Push in and turn the knob to the desired setting Aclicking spark sound will be heard and the burner will light Important Each surface burner is equipped to provide automatic reignition if the flame should somehow get blown out Operating During a Power Failure When lighting the surface burners be sure all of the controls are in the OFF position Strike the match first and hold it in position before turning the knob on 1 Hold a lighted match to the desired surface burner head 2 Push in and turn the control knob slowly on 3 Adjust the flame to the desired level Use amp Care Cooktop To prevent the cooktop from discoloring or staining Clean cooktop after each use Wipe acidic or sugary spills as soon as the cooktop has cooled as these spills may discolor the porcelain Unlike a range with standard gas burners this cooktop does not lift up nor is it removable Do not attempt to lift the cooktop for any reason Sealed Burners The sealed burners o
60. ax Depth of cabinets above cooktop Profondeur max des armoires audessus de l appareil 33 cm 13 po Profundidad m x de los armarios sobre la cubierta 13 33 cm NOTE Figure may not be representative of actual unit REMARQUE L illustration peut ne pas pr senter l appareil actuel NOTA La figura puede no ser exacta a la unidad CLEARANCE DIMENSIONS Range may be installed with zero inches clearance adjacent to against combustible construction at the rear and on the sides below the cooktop For complete information in regard to the installation of wall cabinets above the range and clearances to combustible wall above the cooking top see the installation drawings For SAFETY CONSIDERATIONS do not install a range in any combustible cabinetry which is not in accord with the installation drawings NOTE 30 inch 76 2 cm dimension between cooking top and wall cabinet shown on illustration does not apply to ranges with an elevated oven or microwave The installation instructions of the elevated oven will specify the minimum acceptable dimension between the cooktop and elevated oven The 30 inch 76 2 cm dimension may be reduced to not less than 24 inches 61 cm when the wall cabinets in a domestic home are protected with fireproof materials in accordance with American National Standards National Fuel Gas Code or in mobile homes when they are protected with fireproof materials in accordance with the Federal Standar
61. countertop or Standard proofing without harming the yeast 1 Press More Options pad 2 Select PROOFING E ie 3 Select RAPID or STANDARD CANCEL 4 When proofing is complete remove the dough from the oven and press the CANCEL pid Notes Forany dough that requires one rise either Standard or Rapid Proofing can be used When using frozen bread dough choose RAPID PROOFING There is no need to thaw dough before proofing For dough requiring two rises Standard Proofing must be used for the first rising period Either Standard or Rapid Proofing can be used for the second rise If oven temperature is too high for proofing OVEN COOLING will appear in the display B 11 Use amp Care Keep Warm The Keep Warm feature is used to safely keep hot foods warm or for warming breads and plates 1 2 3 Press More Options pad More Press the arrow to scroll Options Select KEEP WARM Select one of the displayed temperatures or enter desired temperature using the number pads Temperatures can be selected between 145 and 190 F KEEP WARM and the temperature will be displayed When oven has preheated a beep sounds and KEEP WARM and the temperature will be displayed When finished press the CANCEL pad and CANCEL remove food or plates from the oven To Warm Dinner Rolls Cover rolls loosely with foil and place in oven Press More Options pad Select KEEP WA
62. ct the time to cook from the displayed times or use the number pads to enter the cooking time 2006 Maytag Services 16026923 5 The display will show CONVECT DELAY the selected function the preset temperature and the delay time countdown When the delay time has expired the cook time will be displayed and the oven will begin to preheat To set Delay Clean 1 Follow Delay steps 1 4 see below left 2 REMOVE RACKS will show in the display Remove the racks from the oven and select CONTINUE 3 Set LIGHT soil level by entering 200 using the number pads for two hours of cleaning time Select MEDIUM or HEAVY soil level using the Quickset pads There is a brief delay while the door locks 4 DELAY CLEAN the cleaning time the delay time and unlock time based on the selected soil level will show in the display When the delay time has expired the clean time will be displayed and the oven will begin to preheat For more information on self cleaning see pages 5 6 Do not use delayed baking for highly perishable foods such as dairy products pork poultry or seafood Proofing The Proofing feature can be used to raise yeast based bread products prior to baking There are two proofing methods available Rapid and Standard Standard proofing in the oven protects dough from room temperature changes or drafts that commonly affect proofing done on the countertop Rapid proofing provides faster proofing results than
63. ctrode or burner e Replace electrode No spark or only random spark at one ignitor Check for cracked ignitor pinched wire Poor continuity to burner cap Bad ground connection or lack of continuity to ground or ignitor Cracked or broken ignitor extension lead isa e s e Replace ignitor lead or electrode e Clean burner cap and lead e Tighten ground connection and correct any breaks in ground path from ignitor path to unit ground path e Replace ignitor lead Unit continues to spark after knob is turned to OFF position Shorted valve switch harness Switch has slipped off the valve e Replace switch harness If shorting is caused by excessive spillovers customer education is advised e Carefully reposition switch on valve and rotate from OFF to high several times to verify switch is not broken No oven operation in bake or broil No voltage to No voltage from control Loose wire connection or broken wire e Check for 120 VAC at control If no voltage check power source e Check 120 VAC to ignitor if no voltage replace control e Verify all connections are clean and tight replace broken wire No gas flows to burner Ignitor glows red Failed ignitor Gas pressure too high F
64. curely connected inspect ribbon cable and 1626 1 Keyboard disconnected connector shorts breakage corrosion etc If OK replace control 1 4 Board to Board communication failure Replace control 1c6c EEPROM hardware fault Replace control 1c7c Control not calibrated Replace control 1c8c EEPROM CRC error User Options Replace control 1681 EEPROM CRC error Cook Profile Replace control 1d11 Unlocked runaway temperature 600 MUR and harness see Oven Sensor chart If OK change 1d21 Locked runaway temperature 950 NT and harness see Oven Sensor chart If OK change Check connections sensor see Oven Sensor chart and harness If 3d11 Temperature sensor open OK replace control Check connections sensor see Oven Sensor chart and harness If 3d21 Temperature sensor shorted OK replace control Check probe jack and harness If OK check meat probe see Meat 3d41 Meat probe shorted Probe chart Check probe jack and harness If OK check meat probe see Meat 3d51 Meat probe not calibrated Probe chart 4d11 Door switch not closed when locked Check connections switch harness and motor If OK replace control 4d21 No cooling fan rotation Check cooling fan motor and harness If OK replace control 4d31 Cooling fan on when de energized Check cooling fan motor
65. curing side panel to oven chassis drawer 5 Remove screws securing hi limit switch to warming 6 Reverse procedure to reassemble oven door drawer support frame NOTE See page 30 for illustration 6 Label and disconnect hi limit switch wire terminals 7 Remove hi limit switch from outside the warming drawer support frame Oven Door Disassembly NOTE Do not pull hi limit switch and wiring through 1 Remove oven door see Oven Door Removal cavity wall procedure 2 Place door on a protected surface 3 Remove screws securing door glass to oven door trim and frame screws located along the top and bottom edge of oven door Oven Door Removal NOTE Proceed with the following steps if replacing door 8 Reverse procedure to reinstall warming drawer hi limit switch handle A WARNING 4 Remove screws securing door handle to door glass To avoid risk of personal injury or property damage 5 Remove screws securing upper and lower shields do not lift oven door by the handle 6 Remove screws securing door baffle 7 Remove oven door insulation 1 Open oven door slightly and grasp door on both 8 Remove screws securing outer and inner door glass sides and glass frame 2 Lift up and off the hinge receivers 9 Remove oven door liner if replacing 3 Reverse procedure to reinstall oven door 10 Reverse procedure to reassemble oven door NOTE See page 30 for illustration Warming Drawer Track Disassembly Models Remo
66. d for Mobile Home Construction and Safety To eliminate the risk of burns or fire by reaching over heated surface units cabinet storage space located above the surface units should be avoided If cabinet storage is to be provided the risk can be reduced by installing a range hood that projects horizontally a minimum of 5 inches 13 cm beyond the bottom of the cabinets 2006 Maytag Services 16026923 5 Installation Instructions IMPORTANT Keep for Local Inspector cont IMPORTANT conserver pour l inspecteur local suite IMPORTANTE Guarde esta informaci n para el inspector local cont D GAGEMENTS La cuisini re peut tre install e avec un d gagement nul contre des mat riaux combustibles l arri re et sur les c t s en dessous de la table de cuisson Pour des renseignements complets concernant l installation des armoires au dessus de la cuisini re et les d gagements aux parois combustibles au dessus de la surface de cuisson consultez les sch mas sur l installation Pour des RAISONS DE S CURIT n installez pas une cuisini re dans des armoires en mat riaux combustibles non conformes aux sch mas de l installation REMARQUE La dimension de 76 2 cm 30 po entre la surface de cuisson et les armoires murales pr sent es sur l illustration ne concerne pas les cuisini res avec un four sur lev ou un micro ondes Les instructions d installation du four sur lev pr cisent la dimension minimale acceptable entre
67. dequate fastening of the ANTI TIP bracket to the floor or wall The bracket must be installed to engage the RIGHT rear leveling foot Install the bracket as shown in step 2 MOBILE HOMES The installation of a range designed for mobile home installation must conform with the Manufactured Home Construction and Safety Standard Title 24 CFR Part 3280 formerly the Federal Standard for Mobile Home Construction and Safety Title 24 HUD Part 280 or when such standard is not applicable the Standard for Manufactured Home Installations ANSI A225 1 NFPA 501A or with local codes In Canada the range must be installed in accordance with the current CSA Standard C22 1 Canadian Electrical Code Part 1 and Section Z240 4 1 Installation Requirements for Gas Burning Appliances in Mobil Homes CSA Standard CAN CSA Z240MH RECREATIONAL PARK TRAILERS The installation of a range designed for recreational park trailers must conform with state or other codes or in the absence of such codes with the Standard for Recreational Park Trailers ANSI A119 5 latest edition In Canada the range must be installed in accordance with CAN CSA Z240 6 2 Electrical Requirements for R V s CSA Standard CAN CSA 2240 RV Series and Section Z240 4 2 Installation Requirements for Propane Appliances and Equipment in R V s CSA Standard CAN CSA Z240 RV Series CONNECTING THE RANGE Electric Supply The appliance when installed must be electrically grounded i
68. dor desde la parte br leur de gril et serrez la vis Remontez le four d acc s Retire el panel de acceso delantera Voyez les tapes 2 4 Vuelva a colocar ei quemador de asar en su lugar y apriete el tornillo Vuelva a ensamblar el horno Vea los pasos 2 al 4 Remove access panel Retirez le panneau Locate regulator from the front Rep rez le d tendeur 14 16026923 O 2006 Maytag Services Gas Conversion Instructions JGS9900BD Flip the regulator cap and replace the plastic cap Abattez le capuchon du d tendeur et installez le capuchon en plastique Invierta la tapa del regulador y vuelva a colocar la tapa de pl stico Unscrew the regulator cap D vissez le capuchon du Remove the plastic cap Retirez le capuchon en d tendeur Desenrosque la tapa del regulador plastique Retire la tapa de pl stico Screw the cap securely back into place DO NOT OVER Remove the top grates Remove the burner Remove screws and burner head Retirez les vis et la TIGHTEN Revissez bien le chapeau NE LE SERREZ caps Retirez les grilles sup rieures Retirez les t te de br leur Retire los tornillos y la cabeza del PAS TROP FORT Enrosque la tapa firmemente en su chapeaux de br leur Retire las rejillas superiores quemador lugar NO APRIETE DEMASIADO Retire las tapas de los quemadores NATURAL NATUREL GAS NATURAL Carefully remove gas orifice hoods and convert one IMPORTANT Remove and keep old natural gas orifice Replace wit
69. e Convect pad Convect 2 Select BAKE using the Quickset pads 0 Enter the desired temperature using the number pads Press Enter pad to set The temperature can be set from 195 F to 550 F degrees in 5 increments After three seconds the oven will begin to preheat CNVT BAKE and PREHEAT will appear in the display along with 100 or the actual oven temperature whichever is higher The temperature in the display will increase in 1 increments until the oven reaches the preset temperature Allow about 15 minutes for the oven to preheat When the oven is preheated the oven will beep and PREHEAT will turn off and CNVT BAKE will be displayed AUTO will be displayed if Auto Convect Conversion feature is turned on Place food in the oven At the end of cooking turn the oven off by pressing the CANCEL pad Remove food from the oven The oven will continue operating until the CANCEL pad is pressed Convect Roast To set Convect Roast 1 Place food in the oven 2 Press the Convect pad 3 Select CNVT ROAST using the Quickset pads Enter the desired temperature using the number pads Press Enter pad to set The temperature can be set from 195 F to 550 F degrees in 5 increments If Auto Convect Conversion is turned off you can set 170 F 5 Enter desired cook time Enter the conventional roasting time using the number pads After three seconds the oven will beg
70. e chapeau NE LE SERREZ de gicleur du four par l avant Ubique la caperuza del de gicleur du four n 49 pour gaz naturel Retire la PAS TROP FORT Enrosque la tapa firmemente en su orificio del quemador del horno desde la parte delantera caperuza del orificio de gas natural 49 del horno lugar NO APRIETE DEMASIADO CAUTION Ignitor and wires are fragile ATTENTION Allunmeur et fils fragiles ATENCI N El encendedor y el cableado son fr giles You MUST start all hoods by hand to avoid cross threading Vous DEVEZ commencer le vissage de toutes les t tes de gicleur la main pour viter de fausser le filetage UstedDEBE iniciar el enroscado de las tapas a mano para evitar da ar las roscqas Install black 0512 LP orifice hood 4 5 turns DO NOT Position bake burner over bake orifice Reposition bake burner and replace tighten bake OVERTIGHTEN Installez la t te de gicleur noire 0512 hood Positionnez le br leur de cuisson au dessus de burner screws Repositionnez le br leur de cuisson et pour GPL 4 5 tours NE SERREZ PAS TROP la t te de gicleur Coloque el quemador del horno sobre remettez puis resserrez les vis du br leur de FORT Instale la caperuza negra de 0 0512 para gas LP la caperuza del orificio del quemador del horno cuisson Cambie de posici n el quemador del horno y del orificio del quemador 4 a 5 vueltas NO APRIETE vuelva a instalar apretar los tornillos del quemador del DEMASIADO horno
71. e using Quickset pads or the number pads 4 Select BAKE or CONVECT 5 When BAKE is pressed select the temperature using Quickset pads or the number pads 6 When CONVECT is pressed select CNVT BAKE or CNVT ROAST then select the desired temperature using the Quickset pads or the number pads The oven will cook for the selected time then Keep Warm for one hour The oven will automatically turn off Important If the recipe recommends preheating the oven add 15 minutes to the cook time Delay 1 Press the More Options pad More Press the arrow until DELAY is displayed Callens 2 3 Select DELAY 4 Select Delay time using Quickset pads or the number pads 5 Select BAKE CONVECT or CLEAN then select temperature using the Quickset or number pads set Delay Bake Follow Delay steps 1 4 see above 2 Select from the displayed temperatures or use the number pads to enter the temperature 3 Select the time to cook from the displayed times or use the number pads to enter the cooking time 4 The display will show DELAY TIME the selected function the preset temperature and the delay time counidown When the delay time has expired the cook time will be displayed and the oven will begin to preheat To set Delay Convect 1 Follow Delay steps 1 4 see above 2 Select BAKE or ROAST 3 Select from the displayed temperatures or use the number pads to enter the temperature 4 Sele
72. eath disconnect power and gas to range before servicing unless testing requires power and or gas Component Testing Procedures illustration Component Test Procedure 1 Results Oven light amp housing Door plunger switch Autolatch assembly Door lock switch Pressure regulator Oven valve Broil burner JGS9900BD Bake burner Disconnect connector and test resistance of terminals Measure voltage at oven light Remove switch from unit and measure the following points Door closed Door open Disconnect wires and test for continuity per wiring diagram Refer to Parts Manual for correct autolatch switch associated with the correct manufacturing number Switch connection in the following positions Door latch locked Door latch unlocked Verify gas pressure W C P If on LP service verify proper gas supply conversion Verify gas supply is turned on at regulator Attached to pressure regulator Verify gas is supplied Orifice adjusted for Natural or LP Check for obstructions or contamination Verify gas is supplied Orifice adjusted for Natural or LP Check for obstructions or contamination Verify bulb is properly inserted Continuity with bulb inserted 120 VAC see wiring diagram for terminal identification If voltage is not present at oven light check wiring or light switches COM NO Continuity closed COM NO In
73. ectifier AMARILLA Abra el obturador para corregir la situaci n FLAMME BLEUE SE SOULEVANT Fermez l obturateur pour rectifier AZUL QUE SE SEPARA DEL QUEMADOR Cierre el obturador para corregir la situaci n Replace knobs Turn OFF burners Remettez les If necessary adjust both oven burner shutters for correct Replace access panel Remettez le tiroir de boutons Mettez les br leurs sur OFF ARRET Vuelva flames Secure shutter opening with screw Au besoin rangement Vuelva a instalar el cajon de a instalar las perillas APAGUE los quemadores ajustez les deux obturateurs du br leur du four pour obtenir almacenamiento les flammes appropri es Fixez l obturateur avec la vis De ser necesario ajuste ambos obturadores del quemador del horno para obtener la llama correcta Fije la abertura del obturador con el tornillo Replace oven rack Remettre la grille de four Vuelva Move hinges into the first stop position Placez les Replace oven door Replacez la porte du four a instalar la rejilla del horno charni res la premi re position d arr t Mueva las Vuelva a instalar la puerta del horno bisagras al primer tope Close oven door Fermez la porte du four Complete Termin Completo Cierre la puerta del horno O 2006 Maytag Services 16026923 C 17
74. emarque Votre cuisini re peut ne pas comporter certaines des caract ristiques mentionn es dans ce manuel Nota Es posible que esta estufa no venga equipada con todas las caracteristicas que se indican en este manual Printed in USA 2005 Maytag Corporation 16026923 2006 Maytag Services Gas Conversion Instructions JGS8850BD JGS8860BD Caution Burner igniter is fragile Attention L allumeur de br leur est fragile Precauci n El encendedor del quemador es fr gil Lift up and remove oven bottom Soulevez la sole du Remove bake burner screws Retirez les vis du Swing bake burner to the side and lift bake burner off four et retirez la Levante y retire el fondo del horno br leur de cuisson au four Retire los tornillos del the oven orifice Pivotez le br leur de cuisson sur le quemador de horneado c t et soulevez le pour le s parer de son gicleur Gire el quemador del horno a un lado y lev ntelo para sacarlo del orificio Remove warming drawer Retirez le tiroir de Remove screws from panel and then remove Locate regulator from the front Rep rez le d tendeur r chauffage Retire el caj n de calentamiento panel Retirez les vis du panneau puis le panneau lui l avant Ubique el regulador desde la parte delantera m me Retire los tornillos del panel y retire el panel NATURAL NATUREL GAS NATURAL PROPANE PROPANE PROPANO Unscrew the regulator cap D vissez le capuchon du Remove the pl
75. eplace control 1c6c EEPROM hardware fault Replace control 1c7c Control not calibrated Replace control 1c8c EEPROM CRC error User Options Replace control 1681 EEPROM CRC error Cook Profile Replace control 1911 Unlocked runaway temperature 600 F and harness see Oven Sensor chart If OK change 1d21 Locked runaway temperature 950 F pe and harness see Oven Sensor chart If OK change Check connections sensor see Oven Sensor chart and harness If 3d11 Temperature sensor open OK replace control 3421 Temperature sensor shorted Check connections sensor see Oven Sensor chart and harness If OK replace control 3d41 Meat probe shorted Check probe jack and harness If OK check meat probe see Meat Probe chart 3d51 Meat probe not calibrated Check probe jack and harness If OK check meat probe see Meat Probe chart 4d11 Door switch not closed when locked Check connections switch harness and motor If OK replace control 4d21 No cooling fan rotation Check cooling fan motor and harness If OK replace control 4d31 Cooling fan on when de energized Check cooling fan motor and harness If OK replace control 4d41 Cooling fan overspeed Check cooling fan motor and harness If OK replace control 4d51 Door switch circuit fault Check connections harness and motor If OK replace control 9411 Latch will not lock Check wire connections If OK replace motorized door lock
76. es not operate Failed oven Failed wiring esses Failed light Check lamp and replace is necessary Check for broken loose or dirty connections Check light socket for continuity Oven door will not unlock Oven is self cleaning Oven is still hot Allow cycle to complete Will not unlock until unit has cooled to safe temperature Do not force door open this will void warranty Blow cool air on latch area to quicken process Self clean cycle not working Programming Door lock isti scie Turn off circuit breaker for five minutes and try self clean again Verify door lock energizes amp engages 12 16026923 2006 Maytag Services Troubleshooting Procedures WARNING To avoid risk of electrical shock personal injury or death disconnect power and gas to range before servicing unless testing requires power and or gas Description of Fault Codes for EOC III Each fault code consists of 4 digits and is structured as follows 1 Leftmost Digit Primary Failure System 2 Digit Alpha Character 4 Digit Oven Cavity Number 3 Digit Secondary Failure Mechanism 1 Local to Control System d Diagnostic Failure measurable 1 Upper Single Oven
77. everse procedure to reinstall meat probe receptacle switches indicator lights rocker switches and electronic control clock as necessary and transfer to Back Panel Removal the new control panel 1 Remove power from unit 8 Reverse procedure to reinstall contro panel 2 Remove range from installation position see Removing and Replacing Range procedure 3 Remove screws securing back panel to unit 4 Slide back panel up and out to remove 5 Reverse procedure to reinstall back panel Electronic Control Replacement 1 Remove control panel see Control Panel Assembly Replacement procedure steps 1 through 5 2 Remove screws securing electronic control bracket to control panel 3 Label and disconnect terminal wiring from electronic control 4 Slide electronic control down and out of bracket applying slight outward pressure to the inside edges of the electronic control bracket 5 Reverse procedure to reinstall electronic control 2006 Maytag Services 16026923 25 Disassembly Procedures 4 CAUTION To avoid risk of electrical shock personal injury or death disconnect power and gas before servicing unless testing requires power and or gas Cooling Fan Replacement 1 Remove power from unit 2 Remove range from installation position see Removing and Replacing Range procedure 3 Remove back panel see Back Panel Removal procedure 4 Label and disconnect wire terminals from cooling fan 5
78. f your range are secured to the cooktop and are not designed to be removed Since the burners are sealed into the cooktop boilovers or spills will not seep underneath the cooktop However the burner should be cleaned after each use The cap portion of the burner is easily removed for cleaning See page 7 for cleaning directions The burner caps must be correctly placed on the burner base for proper operation of the burner High Performance Burner There is one 16 000 BTU high speed burner on your range located in the right front position This burner offers higher speed cooking that can be used to quickly bring water to a boil and for large quantity cooking Low Turn Down Burner This burner is located in the right rear ES position The Simmer setting can be used to steam or poach foods to cook delicate sauces or continue cooking covered foods The ultra low Melt setting is best for melting chocolate and butter Important When using the normal settings for preparing foods it may take a few minutes for the cooking area to cool to the Melt heat setting BTU ratings will vary when using LP gas Dual Ring Burner select models The cooking surface is equipped with a dual ring burner located in the left front position To operate push in on the control knob and turn counterclockwise to light the burner Continue turning until the desired setting is reached The lighting sequence is inner burner on High t
79. finity open See wiring diagram for schematic layout Common is in neutral position unless locking or unlocking autolatch assembly COM NO Continuity closed COM NO Infinity open 5 Natural 10 LP propane Gas ON Switch up Gas OFF Switch down Gas ON Switch up at regulator Gas OFF Switch down at regulator Factory set to Natural Gas Adjust as necessary Air shutter opening set to 281 to 343 Replace if punctured or torn Factory set to Natural Gas Adjust as necessary Air shutter opening set to 281 to 343 Replace if punctured or torn Bake burner Ignitor Hi limit temperature Switch Temperature sensor ELEMENT WIRE SCHEMATIC Cooling fan motor 2006 Maytag Services Spark module 4 0 Verify gas is supplied Orifice adjusted for Natural or LP Check for obstructions or contamination in ports Test for voltage at terminals Test for circuit amperage Ignitor may glow but not have sufficient amperage to open valve Normally closed verify operation Open 249 to 271 F 121 to 133 C Closed 173 to 207 F 78 to 97 Test for voltage at terminals L and N Check polarity and ground Measure resistance Measure voltage Check motor windings to ground 16026923 Factory set to Natural Gas Adju
80. fire if oven is used without removing grease from the broiler pan When broiling meat that is close to the flame may ignite Trim any excess fat to help prevent excessive flare ups Make sure broiler pan is placed correctly to reduce any possibility of grease fires Should a grease fire occur in the broiler pan turn off oven and keep oven door closed until fire burns out Oven Safety Valve Connecting Range to Gas Install manual shut off valve in gas line for easy accessibility outside range Be aware of the location of the shut off valve Grounded Oven Frame Electrical Requirements 120 volt 60 Hertz 20 amp individual circuit which is properly grounded polarized and protected by a circuit breaker or fuse Extension Cord Do not use extension cords with this product Product Safety Devices Safety devices and features have been engineered into the product to protect consumer and servicer Safety devices must never be removed bypassed or altered in such a manner as to defeat the purpose for which they were intended Listed below are various safety devices together with the reason each device is incorporated in the gas ranges Pressure Regulator Maintains proper and steady gas pressure for operation of oven controls 6 16026923 Regulator must be set for the type of gas being used Natural or LP After servicing regulator make certain it is set properly before completing service Universal orifices are used
81. gh to access side trim 3 Remove screws securing front side trim piece s to oven chassis left and right trim pieces 4 Gently grasp trim piece with both hands pull forward and roll trim piece off retainer clips 5 Reverse procedure to reinstall front side trim piece s Cartridge Assembly Removal Select Models Cooktop cartridges are installed on the left side of the range cooktop 1 Remove power from unit 2 Liftup onthe tab located on the cartridge until top of cartridge clears the opening on the range by 2 inches NOTE Lifting the cartridge too high while still engaged in the receptacle could damage the terminal plug 3 Hold cartridge by the sides and slide away from terminal receptacle 4 Lift cartridge out when fully unplugged 24 16026923 Maintop Assembly Removal Select Models 1 Remove power from unit 2 Remove range from installation position see Removing and Replacing Range procedure 3 Remove front side trim see Front Side Trim Removal procedure 4 Remove air grill grill grates filter aeration pan and cartridges cartridge models 5 Remove cartridge receptacles and grill pans cartridge models 6 Remove screws from plenum area at front of main top cartridge opening cartridge models 7 Remove screws securing top burner assembly to lower burner assembly 8 Label and disconnect wire terminals to ignitors 9 Remove perimeter screws securing main top to chassis
82. h LP gas orifice hoods DO NOT OVERTIGHTEN burner at a time Enlevez soigneusement les t tes de hoods IMPORTANT Retirez et conservez les Remplacez les avec des t tes de gicleur pour GPL NE gicleur pour gaz naturel et convertissez un br leur anciennes t tes de gicleur pour gaz naturel SERREZ PAS TROP Reempl celas con caperuzas de orificios la fois Retire cuidadosamente las caperuzas de los IMPORTANTE Retire y conserve las tapas usadas de de gas LP NOAPRIETE DEMASIADO orificios de gas y convierta un quemador a la vez los orificios de gas natural IMPORTANT Remove and keep old natural gas orifice Replace with LP gas orifice hoods DO NOT OVERTIGHTEN Replace burner heads and screws Hand tighten hoods IMPORTANT Retirez et conservez les anciennes Remplacez les avec des t tes de gicleur pour GPL NE Drop in LP choke R installez les t tes de br leur et t tes de gicleur pour gaz naturel IMPORTANTE Retire y SERREZ PAS TROP Reempl celas con caperuzas de orificios les vis Serrez les la main Posez P trangleur pour conserve las tapas usadas de los orificios de gas natural de gas LP NOAPRIETE DEMASIADO GPL Vuelva a instalar las cabezas y los tornillos del quemador Apriete a mano Coloque el obturador de gas LP en su lugar O 2006 Maytag Services 16026923 C 15 Gas Conversion Instructions JGS9900BD NOTE When reversing an LP conversion back to natural gas the LP choke in step 29 MUST Turn on gas and e
83. hen inner burner on Low then both rings on High then both rings on Low B 4 16026923 Burner Grates The grates must be properly positioned before cooking When installing the grates place the tab ends toward the center matching the straight bars Improper installation of the grates may result in chipping of the cooktop Do not operate the burners without a pan on the grate The grate s porcelain finish may chip without a pan to absorb the heat from the burner flame Use care when stirring food in a pot pan sitting on the burner grate The grates have a smooth finish for ease of cleaning The pot pan will slide if the handle is not held This may result in spilling of hot food items and may be a burn hazard Although the burner grates are durable they will gradually lose their shine and or discolor due to the high temperatures of the gas flame Notes A properly adjusted burner with clean ports will light within a few seconds If using natural gas the flame will be blue with a deeper blue inner cone If the burner flame is yellow or is noisy the air gas mixture may be incorrect Contact a service technician to adjust Adjustments are not covered by the warranty With LP gas slight yellow tips on the flames are acceptable This is normal and adjustment is not necessary With some types of gas you may hear a popping sound when the surface burner is turned off This is a normal
84. hind the range and in the floor under the range should be sealed Make sure the flow of cooling ventilation air is not obstructed below the range Note A range should NOT be installed over kitchen carpeting High Altitude Notice The specified gas burner ratings typically apply to elevations up to 2000 feet For higher altitudes the rates may need to be reduced to achieve satisfactory operation A local certified gas servicer will be able to advise if a reduction is necessary AWARNING Electrical Grounding Instructions This appliance is equipped with a three prong grounding plug for your protection against shock hazard and should be plugged directly into a properly grounded receptacle Do not cut or remove the grounding prong from this plug AWARNING e All RANGES CAN TIP AND CAUSE INJURIES TO PERSONS INSTALL ANTI TIP DEVICES PACKED WITH RANGE FOLLOW ALL INSTALLATION INSTRUCTIONS Arisk of range tip over exists if the appliance is not installed in accordance with the provided installation instructions The proper use of the ANTI TIP device minimizes the risk of TIP OVER In using this device the consumer must still observe the safety precautions as stated in the USE and CARE MANUAL and avoid using the oven doors as a step stool Installation instructions are provided for wood and cement in either floor or wall Any other type of construction may require special installation techniques as deemed necessary to provide a
85. ic control Continuity circuitry Continuity Continuity JGS8850BD Latch Continuity See Detail Continuity Continuity Continuity Cancel Continuity Bake Continuity Broil Continuity Convect Continuity Clean Continuity Detail B Favorites Continuity Rapid Preheat Continuity Warming Drawer Continuity More Options Continuity Setup Continuity 1 Continuity ATM 2 Continuity Back Continuity Enter Continuity Timer 1 Continuity Timer 2 Continuity Oven Light Continuity Trace 1 EE Continuity JGS8750BD Continuity Continuity Continuity Continuity Continuity i Continuity sjo 20 En L do fo qu uU E o J O O1 B 8 fo 20 Li fo jo qw 2006 Maytag Services 16026923 17 Testing Procedures 4 WARNING To avoid risk of electrical shock personal injury or death disconnect power and gas to range before servicing unless testing requires power and or gas Control Component Test Procedure Results Switch membrane assembly Closed circuitry resistance Measurement defined as continuity 2000 Max Q Continuity NOTE To avoid equipment Pins 1 amp 7 are shorted together for control Continuity damage use caution when configuration purposes Continuity checking electronic control Continuity circuitry Continuity Continuity JGS8860B D Latch Continuity Trece 1 See Detail B Continuity Continuity Continuity Continuity Continuity Continuity
86. ication 8 Oven Door Latch Replacement 28 Ram 8 Oven Door Hinge Removal 28 Parts and 8 Bottom Access Panel Removal Select Models 28 Extended Service Plan 8 Bottom Access Panel Disassembly Cori are 9 Select Models 28 Range Description 10 Storage Drawer Removal Select Models 28 Troubleshooting Procedures Storage Drawer Track Disassembly Troubleshooting Chart 11 Select Models 28 Description of Fault Codes for EOC III 13 Storage Drawer Disassembly 28 Fault Code Chart 13 Warming Drawer Removal Select Models 28 Oven Sensor Meat Probe and Warming Drawer Element Removal Cooling Fan Temperature Charts 14 Select Models 28 Testing Procedures Warming Drawer Hi Limit Switch Replacement Component Testing Procedures 15 Select Models 29 Cooling Fan Temperature Chart
87. in to heat CNVT ROAST will appear in the display along with 100 or the actual oven temperature whichever is higher The temperature in the display will increase in 1 increments until the oven reaches the preset temperature Cook time will begin to count down 6 At 75 of the cooking time the oven will beep to let you know to check food Check food using a meat thermom eter If food is done take food out of oven and press CANCEL pad to turn oven off 7 If food is not done continue roasting Once the set time has elapsed the oven will go into Keep Warm mode for 1 hour If food is taken from the oven before the hour CANCEL has elapsed press Notes If the recipe suggests preheating the oven add time to cook time If Auto is off roast time will not be required Rapid Preheat Use to decrease preheating time when using Bake or Convect Bake Use for all foods when baking on one rack After Bake or Convect Bake has been programmed and activated press the Rapid Preheat pad 1 RACK ONLY will display after 10 seconds the display will show RAPID and PREHEAT To return to Standard Preheat Press Rapid Preheat pad again This will provide standard preheat and PREHEAT and the selected function will be displayed Cont 2006 Maytag Services 16026923 B 9 Use amp Care The oven has a variable broil feature which means that a lower broil temperature c
88. installed on a 208 volt circuit Food should be turned halfway through broiling time Broil times may be longer when lower broiling temperatures are selected Broiling Chart SUGGESTED BROIL TIME RACK POSITION Beef broiled to 165 F 10 6 Hamburgers 1 2 thick 2 Ribeye Steaks 1 thick 2 New York Strip Steaks 1 thick 2 T Bone Steaks 1 thick Poultry broiled to 170 F on Low 4 Boneless Skinless Breasts 4 Bone In Chicken Breasts Pork broiled to 160 F 4 Boneless Pork Chops 1 thick 4 Bone In Pork Chops 1 thick Ham Slice 1 thick Fish broiled to 140 F 4 Swordfish Steaks 1 thick 2 Halibut Steaks 1 thick Orange Roughy 1 thick Shrimp 16 20 ct per Ib 2 Salmon Fillets 1 2 thick 2 Salmon Steaks 1 thick 10 12 minutes 18 22 minutes 18 22 minutes 18 22 minutes Low Broil 12 15 minutes 20 33 minutes 20 28 minutes 25 28 minutes 12 16 minutes 10 14 minutes 10 14 minutes 10 12 minutes 8 10 minutes 8 12 minutes 10 14 minutes Important To reduce browning and excess smoke when broiling use a lower rack position and increase the broil time 16026923 2006 Maytag Services Use amp Care OPTIONS More Options Cook amp Hold 2 1 Press the More Options f More 2 Select COOK HOLD Options COOK TIME mI TI o ou 1110 3 Enter cook tim
89. ions and safety practices which should be followed in order to protect the service technician and consumer during service and after service has been completed 1 Gas smell Extinguish any and all open flames and open windows 2 Turn gas off Service range with gas turned off unless testing requires it 4 16026923 2006 Maytag Services Important Safety Information 3 Checking for gas leaks Never check for leaks with any kind of open flame Soap and water solution should be used for this purpose Apply solution to suspected area and watch for air bubbles which indicates a leak Correct leaks by tightening fittings screws connections applying approved compound or installing new parts 4 Using lights Use a hand flashlight when servicing ranges or checking for gas leaks Electric switches should not be operated where leaks are suspected This will avoid creating arcing or sparks which could ignite the gas If electric lights are already turned on they should not be turned off 5 Donotsmoke Never smoke while servicing gas ranges especially when working on piping that contains or has contained gas 6 Check range when service is completed After servicing make visual checks on electrical connection and check for gas leaks Inform consumer of the condition of range before leaving 7 Adhere to all local regulations and codes when performing service Receiving Oven Installer needs to show consumer location of the
90. ipment grounding terminal or lead on the appliance 8 16026923 Model Identification Complete enclosed registration card and promptly return If registration card is missing For Jenn Air product call 1 800 536 6247 or visit the Web Site at www jennair com For Maytag product call 1 800 688 9900 or visit the Web Site at www jennair com For Amana product call 1 800 843 0304 or visit the Web Site at www jennair com For product inCanada call 1 800 688 2002 When contacting provide product information located on rating plate Record the following Model Number Manufacturing Number Serial or S N Number Date of purchase Dealer s name and address Service Keep a copy of sales receipt for future reference or in case warranty service is required To locate an authorized servicer For Jenn Air Maytag product call 1 800 462 9824 or visit the Web Sites at www jennair com or www maytag com ForAmana product call 1 800 628 5782 or visit the Web Site at www amana com For product inCanada call 1 800 688 2002 Warranty service must be performed by an authorized servicer We also recommend contacting an authorized servicer if service is required after warranty expires Parts and Accessories Purchase replacement parts and accessories over the phone To order accessories for your product call For Jenn Air product call 1 800 536 6247 or visit the Web Site at www jennair com For Maytag product call 1 8
91. knob Turn OFF burners Remettez les boutons Mettez les br leur sur OFF ARR T Vuelva a instalar las perilla APAGUE los quemadores 16026923 Adjust flame height with screwdriver Ajustez la hauteur de la flamme avec le tournevis Ajuste la altura de la llama con el destornillador CORRECT BON CORRECTO YELLOW Open shutter to correct JAUNE Ouvrez l obturateur pour rectifier AMARILLA Abra el obturador para corregir la situaci n BLUE LIFTING Close shutter to correct FLAMME BLEUE SE SOULEVANT Fermez l obturateur pour rectifier ff AZUL QUE SE SEPARA DEL QUEMADOR Cierre el obturador para corregir la situaci n If necessary adjust both oven burner shutters for correct flames Secure shutter opening with screw Au besoin ajustez les deux obturateurs du br leur du four pour obtenir les flammes appropri es Fixez l obturateur avec la vis De ser necesario ajuste ambos obturadores del quemador del horno para obtener la llama correcta Fije la abertura del obturador con el tornillo Qe Gas Conversion Instructions JGS8850BD JGS8860BD Replace panel and screws Remettez le panneau et les Replace warming drawer Replacez le tiroir de Replace oven rack Remettre la grille de four Vuelva a vis Vuelva a instalar el panel y los tornillos r chauffage Vuelva a instalar el cajon de instalar la rejilla del horno calentamiento Move hinges into the first stop position Placez les Replace oven
92. la surface de cuisson et le four sur lev La dimension de 76 2 cm 30 po peut tre r duite pas moins de 61 cm 24 po lorsque les armoires murales d une r sidence sont prot g es par des mat riaux ignifuges conform ment aux normes de l American National Standards National Fuel Gas Code Code national des combustibles gazeux ou lorsque les armoires murales d une maison mobile sont prot g es par des mat riaux ignifuges selon la norme f d rale Mobile Home construction and Safety norme de s curit et de construction des maisons mobiles Pour liminer le risque de br lure ou d incendie en passant la main au dessus des l ments de surface chauff s l espace de rangement dans les armoires situ es au dessus des l ments de surface doit tre vit Si une armoire de rangement existe le risque peut tre r duit en installant une hotte d extraction qui d passe horizontalement d un minimum de 13 cm 5 po de la partie inf rieure des armoires DIMENSIONES DE LOS ESPACIOS DE DESPEJE Esta estufa se puede instalar sin espacios de despeje contra superficies combustibles en la parte trasera y a los costados de la misma por debajo de la cubierta Para obtener informaci n completa sobre la instalaci n de los armarios sobre la cubierta y los espacios de despeje para las paredes combustibles sobre la cubierta vea las figuras de instalaci n Por RAZONES DE SEGURIDAD no instale una estufa en ninguna ubicaci n con armarios combustible
93. lectrical supply to product be removed REMARQUE Lorsque vous faites une Ouvrez le gaz et l lectricit reconversion du GPL au gaz naturel alimentant l appareil l trangleur pour GPL de l tape 29 DOIT tre retir Abra el suministro de gas y conecte NOTA Cuando revierta una conversi n de gas el suministro el ctrico al producto LP para usar gas natural DEBE retirar el obturador de gas LP en el paso 29 Replace burner caps Replace grates Remettez les chapeaux de br leur Remettez les grilles Vuelva a instalar las tapas de los quemadores Vuelva a instalar las rejillas ES ZZ 1 8 Flat head Screwdriver Tournevis lame plate de 1 8 po Destornillador de 1 8 de cabeza plana NOTE Repeat steps 33 35 for single burners Adjust each single surface burner one at a time Light Hold knob stem in LOW position Insert screwdriver to REMARQUE R p tez les tapes 33 35 pour les burner and turn to lowest setting Remove knob engage screw Tenez la tige du bouton en position br leurs simples NOTA Repita los pasos 33 a 35 Ajustez chaque br leur de surface simple un par un LOW Introduisez le tournevis pour tourner la para los quemadores sencillos Allumez le br leur et r glez le au niveau le plus bas vis Mantenga la varilla de la perilla en el ajuste Retirez le bouton Ajuste los quemadores superiores LOW Bajo Inserte el destornillador en el tornillo sencillos uno a la vez Encienda el quem
94. los quemadores superiores uno a la vez Bajo Inserte el destornillador en el tornillo Encienda el quemador y aj stelo al nivel m s bajo Retire la perilla CORRECT BON CORRECTO BLUE LIFTING FLAMME BLEVE SE SOULEVANT AZUL QUE SE SEPARA DEL QUEMADOR Replace knobs Turn OFF burners Remettez les Adjust flame height with screwdriver Ajustez la Correct flame height and appearance Flamme de T le hauteur de la flamme avec le tournevis Ajuste la altura hauteur et d aspect apporopri s Altura y apariencia boutons Mettez les br leurs sur OFF ARRET Vuelva a de la llama con el destornillador correctas de la llama instalar las perillas APAGUE los quemadores CORRECT BON CORRECTO YELLOW Open shutter to correct JAUNE Ouvrez l obturateur pour rectifier AMARILLA Abra el obturador para corregir la situaci n BLUE LIFTING Close shutter to correct FLAMME BLEUE SE SOULEVANT Fermez l obturateur pour rectifier AZUL QUE SE SEPARA DEL QUEMADOR Cierre el obturador para corregir la situaci n Replace storage drawer Remettez le tiroir de rangement Vuelva a instalar el caj n de almacenamiento If necessary adjust both oven burner shutters for Replace panel and screws Remettez le panneau et les correct flames Secure shutter opening with screw Au vis Vuelva a instalar el panel y los tornillos besoin ajustez les deux obturateurs du br leur du four pour obtenir les flammes appropri es Fixez l obtu
95. ly pull down and out 2 Reverse procedure to reinstall bottom access panel Bottom Access Panel Disassembly Select Models 1 Grasp top of bottom access panel and gently pull down and out 2 Remove screws securing front panel to glass panel 3 Reverse procedure to reassemble bottom access panel NOTE See page 30 for illustration Storage Drawer Track Disassembly Select Models 1 Remove storage drawer see Storage Drawer Removal Select Models procedure Place drawer on a protected surface Remove screws securing front panel to glass panel Remove screws front panel to storage drawer Remove screws securing sliding tracks to storage drawer Reverse procedure to reassemble akwh o Storage Drawer Disassembly 1 Remove warming door see Storage Drawer Removal Select Models procedure 2 Place door on a protected surface 3 Remove screws securing front panel to glass panel 4 Remove screws securing front panel to storage drawer 5 Remove screws securing sliding tracks to storage drawer 6 Reverse procedure to reassemble storage drawer NOTE See page 30 for illustration Warming Drawer Removal Select Models 1 Slide warming drawer out until drawer stops 2 Press tabs up or down depending on side on warming drawer stops to release drawer from slide track 3 Slide warming drawer completely out of slide track 4 Reverse procedure to reinstall warming drawer Warming Drawer Ele
96. ment Removal ard Models Remove warming drawer see Warming Drawer Removal procedure 2 Remove screws securing element brackets to oven chassis and element 3 Remove element and slide toward front of unit 4 Label and disconnect element wiring Storage Drawer Removal Select Models 5 Reverse procedure to reinstall warming drawer 1 Slide strorage drawer out until drawer stops element 2 Press tabs up or down depending on side on storage drawer stops to release drawer from slide track 3 Slide storage drawer completely out of slide track 4 Reverse procedure to reinstall storage drawer 28 16026923 2006 Maytag Services Disassembly Procedures To avoid risk of electrical shock personal injury or A CAUTION death disconnect power and gas before servicing unless testing requires power and or gas Warming Drawer Hi Limit Switch Warming Drawer Disassembly Replacement Select Models 1 Remove warming door see Warming Drawer 1 Remove unit from installation position see Removal Select Models procedure Removing and Replacing Range procedure 2 Place door on a protected surface 2 Remove front side trim see Front Side Trim 3 Remove screws securing front panel to glass panel Removal procedure 4 Remove screws securing front panel to warming 3 Remove warming drawer see Warming Drawer drawer Removal Select Models procedure 5 Remove screws securing sliding tracks to warming 4 Remove screws se
97. n accordance with local codes or in the absence of local codes with the National Electrical Code ANSI NFPA 70 In Canada the range must be installed in accordance with the current CSA Standard C22 1 Canadian Electrical Code Part 1 Electrical Supply Connection The range requires 120 volts 60 cycle alternating current from a dedicated grounded outlet with a 15 amp circuit breaker See serial plate for rating located on front frame behind storage drawer User may experience occasional circuit tripping if Ground Fault Circuit Interrupter GFCI outlet or breaker is in use 16026923 installation Instructions CONNECTING THE RANGE cont Gas Supply Installation of this range must conform with local codes or in the absence of local codes with the National Fuel Gas Code ANSI 7223 1 latest edition In Canada the range must be installed in accordance With the current CGA Standard CAN CGA B149 Installation Codes for Gas Burning Appliances and Equipment and or local codes In The Commonwealth Of Massachusetts This product must be installed by a licensed plumber or gas fitter when installed within the Commonwealth of Massachusetts T handle type manual gas valve must be installed in the gas supply line to this appliance A flexible gas connector when used must not exceed a length of three 3 feet 36 inches AWARNING Gas leaks may occur in your system and result in a dangerous situation Gas leaks may not be detec
98. n Natural Gas LP Gas Pression d arriv e en pouces la colonne d eau Gaz naturel GPL Presi n de entrada en pulgadas c d a Gas natural Gas LP Max Max M x 14 36 cm 14 36 cm Min Min M n 6 16 cm 11 28 cm Turn off gas and electrical supply to product Fermez le gaz et coupez l lectricit alimentant l appareil Cierre el suministro de gas y desconecte el suministro el ctrico al producto Remove oven rack Retirez la grille du four Retire la parrilla del horno Part No 8101P684 60 LP Propane Conversion lt Instructions Instructions de conversion au GPL Instrucciones de conversion a gas LP propano Only qualified personnel should convert this range Seul un personnel qualifi doit proc der la conversion de cette cuisini re La estufa s lo debe ser convertida por personal calificado Retain natural orifices for future conversion Conservez les gicleurs pour gaz naturel pour une conversion ult rieure Guarde los orificios de gas natural para una conversi n futura Reverse this procedure for LP to natural conversion Proc dez inversement pour la conversion du GPL au gaz naturel Invierta este procedimiento para convertir el producto de gas LP a gas natural Remove oven bottom screws Retirez les vis de la sole du four Retire los tornillos inferiores del horno Lift up and remove oven bottom Soulevez la sole du four et retirez la Levante y retire el fondo del horno
99. o set the clock for a 12 or 24 hour format The clock can be set to display time in either a 12 hour or 24 hour format 1 Press the Setup pad 20 Select CLOCK M d Use the arrow to scroll to the next screen Select 12 24 HOUR Select 12 HR or 24 HR To exit Setup mode press Setup pad on F5 WN Timers Setting the Timers Timer 1 or Timer 2 1 Press TIMER 1 or TIMER 2 pad PARTS TIMER1 2 Press one of the displayed times using the On off Quickset pads or press the number pads to d enter the desired time Important Each press of the displayed time choices adds additional time For example pressing 10 MIN three times provides 30 minutes on the timer 0 30 3 Press Enter pad Changing the amount of time entered once the Timer starts 1 Press the TIMER 1 or TIMER 2 pad once TIMERI On Off 2 Press the displayed times on the Quickset pads repeatedly until the desired time is entered OR 2006 Maytag Services 16026923 3 Press the number pads to enter the new desired time 4 Press Enter pad Canceling the Timer a MN TIMER1 1 Press the TIMER 1 or TIMER 2 pad twice on Jof If both Timers are active gt If the desired Timer is already in the foreground press once for edit mode and twice to cancel the Timer If the desired Timer is not in the foreground follow the steps below 1 Press the desired TIMER pad once The selected Timer will come
100. of 60 000 be used Rigid pipe may also be used HOW TO REMOVE RANGE FOR SERVICING Follow these procedures to remove appliance for servicing 1 Slide range forward to disengage range from the anti tip bracket 2 Shut off gas supply to appliance 3 Disconnect electrical supply to appliance if equipped 4 Disconnect gas supply tubing to appliance 5 Reverse procedure to reinstall If gas line has been disconnected check for gas leaks after reconnection AWARNING DISCONNECT ELECTRICAL SUPPLY BEFORE SERVICING THE APPLIANCE 6 To prevent range from accidentally tipping range must be secured to the floor by sliding rear leveling leg into the anti tip bracket NOTE A qualified servicer should disconnect and reconnect the gas supply The servicer MUST follow installation instructions provided with the gas appliance connector and the warning label attached to the connector SERVICE PARTS INFORMATION When your range requires service or replacement parts contact your dealer or authorized service agency Please give the complete model and serial number of the range which is located on front frame behind storage drawer Your range may not be equipped with some of the features referred to in this manual 16026923 O 2006 Maytag Services installation Instructions IMPORTANT Keep for Local Inspector IMPORTANT conserver pour l inspecteur local IMPORTANTE Guarde esta informaci n para el inspector local 13 33 cm M
101. oking Nomenclature This manual contains information needed by authorized service technicians to install and service gas ranges There may be however some parts which need further explanation Refer to the Installation Instructions Use and Care Technica support line Sheets or the toll free technical 59 9 0 Brand Amana Magic Chef Graffer amp Sattler Hardwick Jenn Air Maytag Norge Universal Crosley lt XEZZCI Butane Dual Fuel Electric Gas Natural Liquid Propane Microwave Standing Pilot No Fuel Warming Drawer B D A a 2xvzrO Product Type Accessory Cartridge Cooktop Updraft Countertop Downdraft Cooktop or Warming Drawer Eyelevel Range Grill Range 20 Range 36 Drop In 24 Wall Oven 27 Range Free Standing 30 Slide In 30 Range Hood OTR Wall Oven RV Range RV Top N Zz o 0mJouzr omooo 2006 Maytag Services znzAoovorromur 16026923 Color Almond on Almond Black Brushed Chrome Traditional White Traditional Almond Prostyle Monochromatic Bisque Stainless Traditional Bisque White on White Frost White True Color White Natural Bisque True Color Bisque Listing UL AGA CSA CGA CUL Dual Listed 220 240 V 50 60 Hz Military Model PSB Approved Singapore Export 120 V 60 Hz UzoocoOo Production Code This identifies the production version Feature C
102. on most valves They must be adjusted for the type of gas being used Natural or LP After servicing a valve or orifice verify it is adjusted properly before completing service Oven valve is designed to be a safety valve Two basic designs are used in gas ranges Hydraulic and Electric Both types are safety valves because they are indirectly operated by the oven thermostat which controls a pilot flame or electric ignitor to open and close the oven valve Ground prong on power cord is connected to the frame usually a green lead fastened by a screw In addition any part or component capable of conducting an electric current is grounded by its mounting If any ground wire screw strap nut etc is removed for service or any reason it must be reconnected to its original position with original fastener before the appliance is put into operation again Failure to do so can create a possible shock hazard 2006 Maytag Services General Information This manual provides basic instructions and suggestions for handling installing and servicing gas ranges The directions information and warnings in this manual are developed from experience with and careful testing of the product If the unit is installed according to this manual it will operate properly and will require minimal servicing A unit in proper operating order ensures the consumer all the benefits provided by clean modern gas cooking Co
103. ontent 1000 3999 Brands 4000 6999 Maytag Amana 7000 9999 Jenn Air General Information Specifications Refer to individual Technical Sheet for specification information Placement of the Oven This freestanding range must be placed in the kitchen or comparable room All safety guidelines must be followed and free air flow around the range is essential Do Not Block Air Vents All air vents must be kept clear during cooking If air vents are covered during operation the oven may overheat If this occurs a sensitive thermal safety device automatically removes power to the oven rendering the oven inoperable The oven will remain in this state until it has sufficiently cooled Location of Model Number To request service information or replacement parts the service center will require the complete model serial and manufacturing number of your slide in range The number can be found on the oven chassis behind the front Access Panel Remove the front Access Panel to view the data Model Number Ask a qualified electrician if you do not understand the grounding instructions or if you have questions when grounding the appliance Keep the electrical power cord dry and keep it from getting crushed or pinched Fora permanently connected appliance This appliance must be connected to a grounded metallic permanent wiring system or an equipment grounding conductor should be run with the circuit conductors and connected to the equ
104. operating sound of the burner If the control knob is turned very quickly from High to Low the flame may go out particularly if the burner is cold If this occurs turn the knob to the OFF position wait several seconds and relight the burner The flame should be adjusted so it does not extend beyond the edge of the pan 2006 Maytag Services Use amp Care Ventilation System The built in ventilation system removes cooking vapors odors and smoke from foods prepared on your cooktop and grill To operate the ventilation system manually push the Bake Fs Vent Fan pad located on the Bron SP electronic control Push once er Cd O for Low push again for High CN and a third time to turn the TIMERI On off fan Off The ventilation system will operate automatically when the grill element is in use The fan can be used to remove strong odors from the kitchen as when chopping onions near the fan Care and Cleaning of the Ventilation System Air Grille The air grille lifts off easily Wipe clean or wash in dishwasher or sink with mild household detergents To prevent scratching the surface do not use abrasive cleaners or scrubbing pads FILTER 2006 Maytag Services 16026923 Filter Turn off ventilation system before removing The filter is a permanent type and should be cleaned when soiled Clean in sink with warm water and detergent or in dishwasher IMPORTANT
105. or EOC III Each fault code consists of 4 digits and is structured as follows 15 Leftmost Digit 2 Digit Alpha Character 37 Digit Secondary 4 Digit Oven Primary Failure System Failure Mechanism Cavity Number 1 Local to Control System d Diagnostic Failure measurable 1 Upper Single Oven 3 Sensor or Meat Probe c Control Related Error not measurable 2 Lower Oven 4 Input to Control System Control System 9 Door Lock If a fault is detected then one of the following three messages will be scrolled on the display FAULT DETECTED PRESS ENTER TO TRY AGAIN This message displays when a fault is detected while a cooking function is active Clear by pressing the Cancel keypad FEATURE NOT AVAILABLE This message displays when a fault is detected while entering data during initial programming and also when a locked out function is detected Clear by pressing any key FAULT DETECTED DISABLE POWER TO CLEAR This message displays when a runaway temperature condition is detected while the control is in idle mode Press any key to clear the message but the fault remains until the control senses a Power On reset Fault Code Description Component to Troubleshoot Replace Ensure ribbon cable is securely connected inspect ribbon cable and 1616 Shorted key connector shorts breakage corrosion etc If OK replace control Ensure ribbon cable is se
106. orifice hood DO NOT OVERTIGHTEN Installez la t te de gicleur noire 0512 pour GPL NE SERREZ PAS TROP FORT Instale la caperuza negra de 0 0512 para gas LP del orificio del quemador NO APRIETE DEMASIADO Remove screw and slide the broil burner forward until the pin clears rear wall Enlevez la vis et faites glisser en avant le br leur de gril jusqu ce que le tenon se trouve d gag de la paroi arri re Retire el tornillo y deslice el quemador de asar hacia adelante hasta que el pasador quede libre de la pared trasera 16026923 Position bake burner over bake orifice hood Positionnez le br leur de cuisson au dessus de la t te de gicleur Coloque el quemador del horno sobre la caperuza del orificio del quemador del horno Caution Burner igniter is fragile Attention L allumeur de br leur est fragile Precauci n El encendedor del quemador es fr gil Slip the broil burner off the broil orifice hood Sortez le br leur de gril de la t te du gicleur de gril Deslice el quemador de asar para sacarlo de la caperuza del orificio 2006 Maytag Services Gas Conversion Instructions JGS8850BD JGS8860BD Remove 52 natural broil orifice hood Retirez la t te Install green 0430 LP broil orifice hood Place the broil burner on the broil orifice hood du gicleur de gril n 52 pour gaz naturel Retire la DO NOT OVERTIGHTEN Installez la t te du gicleur de gril CAUTION Carefully in
107. ornillo Vuelva a ensamblar el horno Vea los pasos 2 al 4 Remove the top grates Remove the burner caps Retirez les grilles sup rieures Retirez les chapeaux de br leur Retire las rejillas superiores Retire las tapas de los quemadores IMPORTANT Keep old natural gas orifice hoods IMPORTANT Conservez les anciennes t tes de gicleur pour gaz naturel IMPORTANTE Conserve las caperuzas usadas de los orificios de gas natural Remount burner heads and replace screws Hand tighten R installez les t tes de br leur et remettez les vis Serrez les la main Vuelva a instalar las cabezas de los quemadores y vuelva a colocar los tornillos Apriete a mano Remove screws and burner head Retirez les vis et la t te de br leur Retire los tornillos y la cabeza del quemador Replace with LP gas orifice hoods DO NOT OVERTIGHTEN Remplacez les avec des t tes de gicleur pour GPL NE SERREZ PAS TROP Reempl celas con caperuzas de orificios de gas LP NO APRIETE DEMASIADO Replace burner caps Replace grates Remettez les chapeaux de br leur Remettez les grilles Vuelva a instalar las tapas de los quemadores Vuelva a instalar las rejillas 16026923 Carefully remove gas orifice hoods and convert one burner at a time Enlevez soigneusement les t tes de gicleur pour gaz naturel et convertissez un br leur la fois Retire cuidadosamente las caperuzas de los orificios de gas y convierta un quemador a la vez
108. ot inserted INSERT PROBE will be displayed 7 Select BAKE or CONVECT Set the oven temperature by selecting one of the displayed temperatures or enter the temperature using the number pads Important If the probe is removed from the oven receptacle at any time during the cooking process the control will prompt INSERT PROBE If the probe is not reinserted within 30 seconds the program will be canceled and the oven will turn off When BAKE is selected The display will briefly show the selected temperatures for the oven and probe After 10 seconds the display will show the actual oven temperature and actual probe temperature When CONVECT is selected Select CNVT BAKE or CNVT ROAST Set the oven temperature by selecting one of the displayed temperatures or enter the temperature using the number pads The display will briefly show the selected temperatures for the oven and probe After 10 seconds the display will show the actual oven temperature and actual probe temperature Cont 2006 Maytag Services Use amp Care 9 When the selected internal temperature of the food has been reached the oven will shut off and a beep will sound 10 Remove the probe from the oven receptacle The probe will be hot Hold probe plug with an oven mitt or potholder when removing from the oven Suggested Internal Food Temperatures INTERNAL TEMPERATURE Ground Beef Fresh Beef Veal Lamb Medium Rare Medium
109. otor windings to ground Disconnect wiring to element and measure cold resistance of terminals Measure voltage at broil element Normally closed verify operation Open 135 to 145 F 57 to 63 C Closed 114 to 126 Normally closed verify operation Open 95 to 105 F 35 to 41 C Closed 79 to 91 F 26 to 33 C Test for voltage at terminals Disconnect wiring and check for continuity in LITE position Test for resistance of spark lead Test ignitor to chassis Verify gas is supplied Verify burner cap is positioned correctly Verify gas is supplied Verify burner cap is positioned correctly Verify cap is positioned correctly Verify cap is positioned correctly Check for debris Verify gas pressure Check orifice for debris Verify gas is supplied Orifice adjusted for Natural or LP Adjust set screw for simmer control 16026923 F 46 to 52 C 120 VAC No continuity RPM Approximately 900 Approximately 31 Q 120 VAC 120 VAC No continuity RPM Approximately 1550 Approx 12 5 to 18 Q 120 VAC Infinite Continuity Infinite Continuity 120 VAC Continuity in LITE position Continuity No continuity from ignitor to chassis Gas supplied Check for obstructions in burner ports Gas supplied Check for obstructions in burner ports Check for obstructions in burner ports Check for obstructions in burner ports
110. over Retirez le couvercle Retire la four Retire el quemador del horno cubierta 16026923 C 13 Gas Conversion Instructions JGS9900BD You MUST start bake and broil hoods by hand to avoid cross threading 5 2 Vous DEVEZ ins rer les t tes de gicleur de cuisson et de gril la main afin d viter qu un filetage ne soit fauss Usted DEBE iniciar el enroscado de las tapas de horneado y asado a mano para evitar dafiar las roscas Remove brass orifice hood Retirez la t te de gicleur Replace orifice hood DO NOT OVER TIGHTEN en laiton Retire la tapa de bronce del orific Remettez la t te de gicleur SANS TROP LA SERRER Reemplace la tapa del orificio NO APRIETE DEMASIADO Reverse steps 6 through 9 to reassemble oven Caution Burner igniter is fragile Attention L allumeur de br leur est fragile Precauci n El encendedor del quemador es fr gil Pour assembler nouveau le four suivez les tapes 6 9 en inversant leur ordre Invierta los pasos 6 al 9 para reensamblar el horno Remove screw and slide the broil burner forward until the Slip the broil burner off the broil orifice hood Sortez pin clears rear wall Enlevez la vis et faites glisser en avant le br leur de gril de la t te du gicleur de gril Deslice le br leur de gril jusqu ce que le tenon se trouve d gag el quemador de asar para sacarlo de la caperuza del de la paroi arri re Reti
111. pliance contains or produces a chemical or chemicals which are known to the state of California to cause cancer birth defects or other reproductive harm To reduce the risk from substances in the fuel or from fuel combustion make sure this appliance is installed operated and maintained according to the instructions in this manual Due to the nature of cooking fires can occur as a result of overcooking or excessive grease Although a fire is unlikely if one occurs proceed as follows Oven Fires Do not open the oven door Turn all controls to OFF As an added precaution turn off the electricity at the main circuit breaker or fuse box and the gas atthe main supply valve Allow the food or grease to burn itself out in the oven If smoke or fire persist call the local fire department To avoid the risk of property damage or personal injury do not obstruct the flow of combustion or ventilation air to the oven To avoid the risk of electrical shock serious personal injury or death Make sure your oven has been properly grounded and always disconnect the electrical supply before servicing this unit NOTE The maximum gas supply pressure for these models must not exceed 14 inches W C P Safety Practices for Servicer Safe and satisfactory operation of gas ranges depends upon its design and proper installation However there is one more area of safety to be considered Servicing Listed below are some general precaut
112. programming process Control panel features vary by model Oven display above is programmed for a bake operation If you need to back out of a function or option in the display press the Back pad When your programming is complete Convect Use for convection baking and roasting press the Enter pad or wait four seconds and the function will start automatically Rapid Preheat Use to decrease preheating time Bake Use for baking and roasting Up arrows indicate additional screens with additional options Press the Quickset pads next to the arrows to scroll through TIMER 1 Sets timer the display Broil Use for broiling and top browning Display Displays oven functions options and window time of day TIMER 2 Sets timer CN Number Pads Use to enter time and temperature C or to enter Favorites names Important Four seconds after entering the function Favorites Use to access program or save option number or letter the function will automatically be baking cycles entered If more than 30 seconds elapse between steps in More Options Use to access additional features programming the function will be canceled and the display will return to the previous display Clean Use to set self clean cycle Setup Use to view or change factory Clock deraut s ttings Setting the Clock Vent Fan Activates the ventilation fan on fa SN the cooktop 1 Press the Setup pad Setup On Off Oven Light Use
113. ptable If the cut depth exceeds 23 1 2 use filler kit K71FILL B black W white S Stainless may be ordered from dealer NOTE As an option to make gas valve accessible it can be located in the adjacent cabinet REMARQUE Pour que le robinet de gaz soit accessible il peut tre situ dans l armoire adjacente NOTA A modo opcional para facilitar el acceso a la v lvula de gas la misma puede ser instalada en el gabinete adyacente Important Because of continuing product improvements Maytag reserves the right to change specifications without notice Dimensional specifications are provided for planning purposes only Important En raison de l am lioration continue de ses produits Maytag se r serve le droit de changer les sp cifications sans pr avis Les dimensions ne sont fournies qu titre indicatif Importante Debido a las mejoras continuas del producto Maytag se reserva el derecho de cambiar sus especificaciones sin aviso previo Las especificaciones dimensionales se proporcionan para prop sitos de planificaci n nicamente O 2006 Maytag Services 16026923 installation Instructions Included Compris Se incluye Not Included Non inclus No se Tools Needed Outils n cessaires incluye Herramientas Necesarias If you have LP propane it is recommended to initiate the conversion prior to installation The conversion instruction kit can be found on the regulator shelf behind the shield Avec le G
114. rateur avec la vis De ser necesario ajuste ambos obturadores del quemador del horno para obtener la llama correcta Fije la abertura del obturador con el tornillo Replace oven bottom Replace oven bottom screws Remettez les vis de la Replace oven rack Remettre la grille de four Vuelva a Remettez le panneau inf rieur du four sole du four Vuelva a instalar los tornillos inferiores instalar la rejilla del horno Vuelva a instalar el panel inferior del horno del horno O 2006 Maytag Services 16026923 C 5 Gas Conversion Instructions JGS8850BD JGS8860BD This range is equipped with fixed orifices on all burners and a convertible appliance regulator The unit serial plate states which gas it was adjusted for at the factory To convert the unit to either Natural gas or LP gas will require replacement of the oven orifice hoods and the top burner orifice hoods and adjustment of the oven burner shutters and the appliance pressure regulator converter cap Cette cuisini re est quip e de gicleurs fixes sur tous les br leurs et d un d tendeur convertible La plaque signal tique de cet appareil indique le r glage fait l usine pour un certain gaz La conversion de l appareil au gaz naturel ou au GPL n cessite le remplacement des t tes de gicleur du four et des t tes de gicleur du br leur sup rieur ainsi que le r glage des obturateurs de br leur du four et du capuchon du convertisseur du d tendeur Esta estufa viene equipad
115. rature on Friday at 2 pm and stay in Sabbath mode for 33 hours SABBATH and SABBATH ENABLE appear in the display for 90 minutes If Bake or Cook Hold Bake are desired during Sabbath Mode they must be programmed during this 90 minute time before AUTO Sabbath Mode is active MANUAL sets the oven to Sabbath Mode for 72 hours SABBATH and SABBATH ENABLE appear in the display for five minutes If Bake or Cook Hold Bake are desired during Sabbath Mode they must be programmed during this five minute time before the MANUAL Sabbath Mode is active 2006 Maytag Services 16026923 5 Select ON or OFF 6 Press Setup pad to exit the Setup menu To cancel Sabbath Mode Press and hold the Setup pad for five seconds Satt N The Bake mode may be cancelled by pressing On 4 the CANCEL pad during Sabbath US Notes The oven must be idle to program Sabbath Mode Sabbath Mode cannot be turned on if the keypads are locked out or when the door is locked If the oven is baking when Auto Sabbath Mode starts there will be no audible beeps All prompts messages and beeps are deactivated when the Sabbath Mode is active If the oven light is desired while in Sabbath Mode it must be turned on before the Sabbath Mode is set The self clean cycle and automatic door lock do not operate during the Sabbath Mode The Bake temperature can be changed during an Active Sabbath Mode Simply press the Bake pad and then enter the desired
116. re To reactivate Auto Convect Conversion 1 Press Setup pad 2 Select AUTO CONVECT 3 Select ON 4 Press Setup pad to exit the Setup menu Setup On Of Notes When using Convect Bake and Convect Pastry with the Auto Convect Conversion option turned off reduce the set temperature by 25 F f Convect Roasting with the Auto Convect Conversion option turned off you will not be required to program a cooking time Check food at 75 of the conventional time C F The displayed temperature scale can be changed from Fahrenheit to Celsius To change the scale Pp Setup 1 Press Setup pad On Off Use the arrow to scroll to the next screen 2 3 Select C F 4 Select the desired temperature scale 5 Press Setup pad to exit the Setup menu Sabbath Mode The oven is set to shut off after 12 hours if you accidentally leave it on The Sabbath Mode overrides the 12 hour shut off and can either be set to come on automatically or can be set manually as desired Only Bake or Cook Hold Bake will operate when the oven is in Sabbath Mode All other functions are invalid If a function other than Bake or Cook Hold Bake is in operation when Sabbath Mode starts the function will be canceled To activate Sabbath Mode 1 Press Setup pad Setup On Off 2 Press the arrow to scroll 3 Select SABBATH 4 Select AUTO or MANUAL AUTO will automatically prompt you to enter a Bake tempe
117. re el tornillo y deslice el quemador orificio de asar hacia adelante hasta que el pasador quede libre de la pared trasera Remove 1 42 natural broil orifice hood Retirez la t te Install 038 LP broil orifice hood Place the broil burner on the broil orifice hood du gicleur de gril n 1 42 pour gaz naturel Retire la 4 5 turns DO NOT OVERTIGHTEN Installez la t te du CAUTION Carefully insert burner pin in oven back caperuza del orificio de gas natural 1 42 del quemador gicleur de gril 038 pour GPL 4 5 tours NE SERREZ Mettez le br leur de gril sur la t te du gicleur de gril de asar PAS TROP Instale la caperuza de 0 038 para gas LP del ATTENTION Ins rez soigneusement le tenon du br leur orificio del quemador de asar dans le four Coloque el quemador de asar en la 4 a 5 vueltas NO APRIETE DEMASIADO caperuza del orificio PRECAUCION Inserte cuidadosamente el pasador en la parte trasera del horno CAUTION Pin MUST be inserted into back of hole on oven to secure burners C5 ATTENTION Le tenon DOIT tre introduit l arri re du trou du four pour bien loger les br leurs C5 ATENCION El pasador DEBE ser introducido en la parte trasera del agujero en el horno para asegurar los quemadores C5 1 ES Reposition the broiler burner and tighten screw Re assemble oven See steps 2 4 Remettez en place le abia l avant Ubique el regula
118. ring through cavity wall 3 Label and disconnect wire terminals 4 Reverse procedure to reinstall sensor NOTE Verify sensor wires are pushed through the insulation 2006 Maytag Services Disassembly Procedures To avoid risk of electrical shock personal injury or A CAUTION death disconnect power and gas before servicing unless testing requires power and or gas Regulator Removal 7 Remove screw securing light socket to oven cavity 1 Disconnect power before servicing 8 Label and disconnect wire terminals from light socket 2 Remove range from installation position see 9 Reverse procedure to reinstall light socket Removing and Replacing Range procedure NOTE Reposition fiberglass insulation around light 3 Disconnect tubing from regulator socket to eliminate the possibility of any heat 4 Remove screws securing bracket to back of unit related problems 5 Remove screws securing regulator to support bracket PAS 6 Reverse procedures to reassemble NOTE When reconnecting supply line to regulator use NI pipe dope compound to seal the connection Socket NOTE Perform gas leak test a Gas Valve Removal Select Models Bulb specifications NOTE Removal of range from installation position is G5 3 Type Halogen Bi Pin 25W 120V required E before Oven Vent Smoke Eliminator Removal Remove range from installation position see Select Models Removing and Replacing Range procedure
119. ripped Replace household fuse See Control Systems Troubleshooting Fan motor does not operate No power to fan motor Failed fan motor or winding frozen Lr Check for 120 VAC supplied at fan motor If voltage is not present check for broken loose wiring between fan motor and relay board If voltage is present at fan motor go to next step Check motor winding for continuity Check for a frozen motor shaft Check for broken wiring between motor and neutral terminal block Oven smokes odor first few times of usage Minor smoking and or odor is normal the first few times of oven usage Failure Codes Electronically Controlled See Fault Code Chart Oven not operating Programming Power Unit in Sabbath mode Switch range circuit breaker off for five minutes and try oven again Verify power is present at unit and circuit breaker is not tripped Replace household fuse Refer to Use amp Care manual to remove unit from Sabbath mode Clock and timer not working Power Electronic Control locked Verify power is present at unit and circuit breaker is not tripped Replace household fuse Refer to Use and Care manual to unlock electronic control Oven light do
120. rvices Testing Procedures 4 WARNING To avoid risk of electrical shock personal injury or death disconnect power and gas to range before servicing unless testing requires power and or gas Relay Logic for 1 NOTE Subsequent changes implemented after the release of this technical sheet may have altered the parameters identified in this chart INDEX X OFF O ON E CYCLING ON OR OFF DETERMINED BY USER INPUT COOKING MODE IDLE BAKE RAPID PREHEAT BAKE PREHEAT BAKE HIGH BROIL PREHEAT HIGH BROIL LOW BROIL PREHEAT LOW BROIL CLEAN PREHEAT CLEAN KEEP WARM PREHEAT KEEP WARM WARMING DRAWER HIGH WARMING DRAWER LOW CONVECT ROAST PREHEAT CONVECT ROAST CONVECT BAKE RAPID PREHEAT CONVECT BAKE PREHEAT CONVECT BAKE CONVECT PASTRY RAPID PREHEAT CONVECT PASTRY PREHEAT CONVECT PASTRY THAW SERVE DRYING PREHEAT DRYING RAPID PROOFING STANDARD PROOFING Convection fan stops when oven door is opened XIXIXIX MW X X X X X x X X XI x W o REX XX X W O BAKE ELEMENT XIXIXIX MH X X X x x KEKE KEK x X X WH BROIL ELEMENT x CONVECT ELEMENT 019 x x x x CONVECT FAN WARMING DRAWER
121. s approuv pour le GPL Tenez toujours le d tendeur en position stable lors du raccordement de la conduite d alimentation en gaz Aplique compuesto para roscas de tuberias aprobado para gas LP a todas las roscas Siempre sostenga el regulador en una posici n estable mientras conecta la tuberia de suministro TURN ON GAS SUPPLY TO PRODUCT OUVREZ L ALIMENTATION EN GAZ DE L APPAREIL ABRA EL SUMINISTRO DE GAS AL PRODUCTO Adjust legs Note Check counter top height see dimensions to allow range top to clear countertop Installer take caution not to damage floor Ajustez les pieds Remarque V rifiez la hauteur du plan de travail voyez les dimensions pour que le dessus de la cuisini re se trouve au dessus du plan de travail Installateur faites attention de ne pas endommager le sol Ajuste los tornillos niveladores Nota Verifique la altura de la encimera vea las dimensiones para permitir que la parte superior de la estufa pase por la misma Instalador tenga cuidado de no dafiar el piso 16026923 installation Instructions 10 Insert plug into grounded outlet Ins rez la fiche dans la prise mise la terre Conecte el enchufe en un tomacorriente puesto a tierra RS Make sure flexible connector and electrical cord are not kinked Assurez vous que le raccord flexible et le cordon d alimentation ne sont pas entortill s Aseg rese de que el conector flexible y el cord n el ctrico no est n doblados
122. s que no concuerden con las figuras de instalaci n NOTA El despeje de 30 pulgadas 76 2 cm entre la cubierta de cocci n y el armario que se muestra en la figura no se aplica a las estufas con hornos elevados o a los microondas Las instrucciones de instalaci n del horno elevado especificar n el espacio m nimo entre la cubierta y el horno elevado El despeje de 30 pulgadas 76 2 cm puede ser reducido a no menos de 24 pulgadas 61 cm cuando los armarios del hogar est n protegidos con materiales a prueba de fuego de acuerdo con las Normas Nacionales de Estados Unidos ANS y el C digo Nacional de Gas 0 en las casas rodantes cuando las mismas est n protegidas con materiales a prueba de fuego de acuerdo con la Norma Federal de Construcci n y Seguridad de Viviendas M viles Para eliminar el riesgo de quemaduras o de incendios cuando se intenta alcanzar alg n objeto sobre los elementos superiores evite almacenar art culos en los armarios que est n sobre la estufa Si se instala un armario sobre la cubierta se puede reducir el riesgo instalando una campana de ventilaci n que se proyecte horizontalmente en un m nimo de 5 pulgadas 13 cm m s all de la base de los armarios A WARNING AVERTISSEMENT ADVERTENCIA THIS PRODUCT SHOULD NOT BE INSTALLED BELOW VENTILATION TYPE HOOD SYSTEM THAT DIRECTS AIR IN A DOWNWARD DIRECTION THESE SYSTEMS MAY CAUSE IGNITION AND COMBUSTION PROBLEMS WITH THE GAS BURNERS RESULTING IN PERSONAL INJURY AND MAY EF
123. sert burner pin in oven back caperuza del orificio de gas natural 52 del quemador verte 0430 pour GPL NE SERREZ PAS TROP Instale la Mettez le br leur de gril sur la t te du gicleur de gril de asar caperuza verde de 0 0430 para gas LP del orificio del ATTENTION Ins rez soigneusement le tenon du br leur dans quemador de asar NO APRIETE DEMASIADO le four Coloque el quemador de en la caperuza del orificio PRECAUCI N Inserte cuidadosamente el pasador en la parte trasera del horno Reposition the broiler burner and tighten screw Re Remove the top grates Remove the burner Remove screws and burner head Retirez les vis et la assemble oven Remettez en place le br leur de gril et caps Retirez les grilles sup rieures Retirez les t te de br leur Retire los tornillos y la cabeza del serrez la vis Remontez le four Vuelva a colocar ei chapeaux de br leur Retire las rejillas superiores quemador quemador de asar en su lugar y apriete el tornillo Retire las tapas de los quemadores Vuelva a ensamblar el horno Carefully remove gas orifice hoods and convert one IMPORTANT Remove and keep old natural gas orifice Replace with LP gas orifice hoods DO NOT burner at a time Enlevez soigneusement les t tes de hoods IMPORTANT Retirez et conservez les anciennes OVERTIGHTEN Remplacez les avec des t tes de gicleur gicleur pour gaz naturel et convertissez un br leur la t tes de gicleur pour gaz naturel IMPO
124. st as necessary Air shutter opening set to 469 to 531 Replace if punctured or torn 120 VAC 3 2 3 6 Amps If not replace Infinite Continuity 120 VAC See wiring diagram Approximately 1000 O at room temperature 75 F 23 8 C 120 VAC No continuity RPM Approximately 1670 to 2070 15 Testing Procedures 4 WARNING To avoid risk of electrical shock personal injury or death disconnect power and gas to range before servicing unless testing requires power and or gas Illustration Component Test Procedure 1 Results 16 JGS8850BD JGS8860BD lt a JGS8850BD JGS8860BD Convection motor single speed Convection element Downdraft motor Warmer element Hi limit temperature switch Warming Drawer Hi limit temperature switch Warming Drawer Spark switch Spark ignition electrode Top surface burner 5 K btu 9 2 K btu 16 K btu Top surface dual ring burner 15 K btu Inner 3 K btu Outer 12 K btu Top surface burner cap 5 K btu 9 2 K btu 16 K btu Top surface burner cap dual ring inner and outer rings Orifice Orifice holder 5 K btu 9 2 K btu 16 K btu Burner valve push to turn 270 5 K btu 9 2 K btu 16 K btu Measure voltage Check motor windings to ground Disconnect wiring to element and measure cold resistance of terminals Measure voltage at convect element Measure voltage Check m
125. t the request Press Setup to exit Sabbath Mode Press the Setup pad then press the right Press the left ATM pad to select Manual Sabbath Based on the Jewish guidelines ATM pad until SABBATH displays Press mode or the right ATM pad to select Auto Sabbath for Sabbath Holiday the left ATM pad to select SABBATH mode Press the left ATM pad to turn on Sabbath requirements settings mode or the right ATM pad to turn off Sabbath mode Press Setup to exit Time Options Press the Setup pad then the left ATM Press the right ATM pad to scroll to the desired Determines control time day of pad to select TIME OPTIONS function to modify week 12 24 hour clock Time Set Press the Setup pad then the left ATM Enter the correct time using the digits pads and Determines time of day to display pad then the left ATM pad again to set the press Enter Press the left ATM pad to select AM on control time of day clock or the right ATM pad to select PM Press Setup to exit Day of Week Press the Setup pad then the left ATM Press the right ATM pad until the correct day Determines day of week Monday pad then press the right ATM pad until displays then press the left ATM pad to select thru Sunday to display on DAY displays Press the left ATM pad to Press Setup to exit control set the day of the week 12 24 Hour Clock Display Press the Setup pad then the left ATM Press the left ATM pad to select 12 hour clock or Determines 12 hour or 24 hour pad
126. ted by smell alone Gas suppliers recommend you purchase and install an UL approved gas detector Install and use in accordance with manufacturer s instructions GAS SUPPLY CONNECTION A QUALIFIED SERVICEMAN OR GAS APPLIANCE INSTALLER MUST MAKE THE GAS SUPPLY CONNECTION Leak testing of the appliance shall be conducted by the installer according to the instructions given in Step 7 Apply a non corrosive leak detection fluid to all joints and fittings in the gas connection between the supply line shut off valve and the range Include gas fittings and joints in the range if connections were disturbed during installation Check for leaks Bubbles appearing around fittings and connections will indicate a leak If a leak appears turn off supply line gas shut off valve tighten connections turn on the supply line gas shut off valve and retest for leaks CAUTION NEVER CHECK FOR LEAKS WITH A FLAME WHEN LEAK CHECK IS COMPLETE WIPE OFF ALL RESIDUE NATURAL GAS SUPPLY LINE MUST HAVE A NATURAL GAS SERVICE REGULATOR INLET PRESSURE TO THIS APPLIANCE SHOULD BE REDUCED TO A MAXIMUM OF 14 INCHES WATER COLUMN 0 5 POUNDS PER SQUARE INCH 5 1 LIQUEFIED PETROLEUM L P PROPANE GAS SUPPLY LINE MUST HAVE A L P GAS PRESSURE REGULATOR INLET PRESSURE TO THIS APPLIANCE SHOULD BE REDUCED TO A MAXIMUM OF 14 INCHES WATER COLUMN 0 5 P S I INLET PRESSURES IN EXCESS OF 0 5 P S I CAN DAMAGE THE APPLIANCE PRESSURE REGULATOR AND OTHER GAS COMPONENTS IN T
127. temperature using the Quick set pads Pressing the CANCEL pad will cancel a Bake cycle however the control will stay in the Sabbath Mode The day of the week and AM PM must be set for Sabbath Mode to operate correctly Temp Adjust Oven temperatures are carefully tested at the factory It is normal to notice some baking time or browning differences between a new oven and an old one As ovens get older the oven temperature can shift You may adjust the oven temperature if you think the oven is not baking or browning correctly To decide how much to change the temperature set the oven temperature 25 F higher or lower than the temperature in your recipes then bake The results of the first bake should give you an idea of how much to adjust the temperature To adjust the oven temperature rS Setup 1 Press Setup pad On Off E 2 Press the arrow to scroll 3 Select TEMP ADJUST 4 Enter the desired temperature change using the number pads 5 Select to indicate an increase or decrease in temperature The temperature change is displayed at the top of the window 6 Press Enter pad or wait three seconds to accept the change 7 Press Setup pad to exit the menu The oven temperature does not need to be readjusted if there is a power failure or interruption Broiling and cleaning temperatures cannot be adjusted B 15 Use amp Care Tones beeps The number of beeps heard at the end of cooking
128. tically reduce temperature to 170 F and keep the food warm for up to an hour and then automatically turn off When using Delay the oven begins to cook later in the day Set the amount of time that you want to delay before the oven turns on and how long you want to cook The oven begins to Bake CANCEL 16026923 heat at the selected time and cooks for the specified length of time When that time has elapsed the oven will keep the food warm for up to an hour then automatically turn off To set Cook amp Hold 1 After Bake has been programmed press the More Options pad 2 Select COOK HLD More gt Options 3 Select the amount of time you want to bake by pressing the Quickset pads or the number pads Press ENTER COOK TIME the cook time countdown PREHEAT BAKE and the actual temperature will be displayed a The oven will cook for the selected time then keep food warm for one hour To set a Delay More 1 After Bake has been programmed press J Options the More Options pad Select DELAY Select the amount of time you want to delay the start of cooking using the displayed times or the number pads 4 Select the amount of time you want to cook using the displayed times or the number pads 5 The display will show BAKE the temperature the delay time and the cook time countdown 6 When the delay time has expired the oven will begin heating COOK TIM
129. tion relev e pour d gager le haut NOTA Para los mostradores con borde delantero formado cepille la secci n elevada para que la parte superior calce CAUTION Some white European style cabinets are equipped with delicate white vinyl drawer and door fronts The vinyl may not be designed to withstand the heat produced by the normal safe operation of a self clean range Discoloration or delamination may occur To avoid possible damage we recommend increasing the 30 cabinet opening to 31 1 4 minimum and using heat shield CABKIT V The countertop cut out must remain 30 ATTENTION Certaines armoires de couleur blanche et de style europ en sont quip es de fa ades de porte et de tiroir en vinyle blanc fragile Le vinyle peut ne pas tre con u pour r sister la chaleur produite par un autonettoyage normal peut se produire une d coloration ou une d stratification Pour viter le risque de dommages nous vous recommandons d agrandir l ouverture dans les armoires de 30 po 76 2 cm 31 1 4 po 79 4 cm minimum et d utiliser un ensemble d cran thermique CABKIT V L ouverture dans le plan de travail doit toujours tre de 30 po 76 2 cm 1 1 2 min 8 8 cm 1 1 2 min 8 8 cm IZ XA If cabinet backsplash behind unit is not present kit UXA9107AA B black S stainless W white may be ordered from dealer When replacing an existing unit a maximum of 23 1 2 is acce
130. to turn the oven light on or off 2 Select CLOCK using the Quickset pads is CANCEL Cancels all operations except Timer 3 Select TIME Clock Favorites Setup and Vent Fan 4 Enter the time using the number pads Quickset pads Use to select options in display 5 Press Enter pad Window meo pido 6 Select AM or PM in 12 hour mode For 24 hour clock see on both sides page 16 7 To exitthe Setup mode press Quickset Pads Quickset pads are located on each side of the display window and are used to select the desired function or option in the display window To select the option or function press the Quickset pad next to the word B 6 16026923 2006 Maytag Services Use amp Care Activating and canceling the clock day of week display PER Setup On Off 1 Press Setup pad Select CLOCK Press the arrow to scroll until DISABLE is displayed Select DISABLE Select TIME Select OFF to turn the clock display off or select ON to turn the clock display on 7 Select OFF to turn the day of the week display off Select ON to turn the weekday display on ona 5 Setup On Off 8 To exit the Setup mode press Setup pad Entering the day of the week 1 Press Setup pad Select CLOCK Press the arrow to scroll until DAY is displayed 2 3 4 Use Quickset arrow to scroll through the days 5 Select day desired 6 To exit the Setup mode press Setup pad T
131. ts and damage to porcelain surface s Do not touch interior surfaces of oven during or immediately after use Do not let clothing or other flammable materials come in contact with bake or broil burners Other areas of the oven can become hot enough to cause burns such as vent openings window oven door and oven racks To avoid steam burns do not use a wet sponge or cloth to wipe up spills on hot cooking area Do not store combustible or flammable materials such as gasoline or other flammable vapors and liquids near or in oven Do not clean oven door gasket located on back of the door Gasket is necessary to seal the oven and can be damaged as a result of rubbing or being moved Do not drape towels or any materials on oven door handles These items may ignite causing a fire 16026923 5 Important Safety Information 4 amp CAUTION Do not store items of interest to children in cabinets above range Children may climb on oven to reach these items and become seriously injured Baking Broiling and Roasting Gas Burner Orifices Do not use oven area for storage Stand back from range when opening door of a hot oven Hot air or steam can cause burns to hands face and eyes Do not use aluminum foil anywhere in the oven This could result in a fire hazard and damage the range Use only glass cookware appropriate for use in gas ovens Always remove broiler pan from oven when finished broiling Grease left in pan can catch
132. turn to the Favorites menu RECIPE LIST will be displayed 7 Press Favorites pad to exit Favorites menu To Delete a Favorite Recipe 1 Press Favorites pad Favorites Press arrow key to scroll 4 2 3 Select DELETE RECIPE 4 Find recipe to be deleted You may need to press arrow key to find desired recipe 5 The Control will ask again to make sure you want to delete that recipe Select YES or NO 6 Press Favorites pad to exit Favorites menu To exit out of Favorites at any time press the Favorites pad Language The language of the screens in the display window can be set to English French or Spanish To change the display language from English NR Setup On Off 1 Press Setup pad 2 Select LANGUAGE 3 Use the arrow to scroll to next screen if needed 4 Select the desired language 5 Press Setup pad to exit the Setup menu Auto Convect Conversion The oven comes from the factory set for Auto Convect Conversion Auto Convect Conversion automatically reduces the set temperature by 25 for Convect Bake For Convect Roast the control will alert you at 75 of the programmed roasting time to check foods for doneness Convect roast temperatures are not reduced To deactivate Auto Convect Conversion 1 Press Setup pad Setup 2 Select AUTO CONVECT KOR FOR 3 Select OFF m 4 Press Setup pad to exit the Setup menu Cont 2006 Maytag Services Use amp Ca
133. urchased this product For further assistance please contact Customer Service Support Center CAIR Center Web Site Telephone Number WWW JENNAIR COM eee 1 800 536 6247 WWW MAYTAG COM ee 1 800 688 9900 WWW AMANA COM eene 1 800 843 0304 Center in Canada 1 800 688 2002 Recognize Safety Symbols Words and Labels 4 DANGER DANGER Immediate hazards which WILL result in severe personal injury or death amp WARNING WARNING Hazards or unsafe practices which COULD result in severe personal injury or death 44 CAUTION CAUTION Hazards or unsafe practices which COULD result in minor personal injury product or property damage 16026923 2006 Maytag Services Table of Contents Important Information 000 rr 2 Manifold Assembly 25 Important Safety Information Control Panel Assembly Removal 25 What to Do if You Smell 4 Electronic Control Replacement 25 Oven E Ires 4 Burner Switch 25 Safety Practices for Servicer 4 Meat Probe Receptacle Replacement SOIVICIN cascara 4 Select Models assa 25 Receiving Oven sss 5 Back Panel Removal
134. ure NOTE If replacing manifold only skip step 2 Convection Broil Element Fan 2 Loosen and disconnect fittings securing surface burner tubing to burner assembly and manifold Remove bolt s securing surface valve s to manifold Remove bolt securing shut off valve from manifold Disconnect tubing from manifold to the regulator Reverse procedures to reassemble Element NOTE Perform gas leak test Meat Probe Receptacle Replacement Control Panel Assembly Removal Select Models 1 Remove power from unit 1 Remove power from unit 2 Remove burner switch control knobs 2 Remove range from installation position see 3 Remove front screws securing control panel to Removing and Replacing Range procedure chassis 3 Remove front side trim see Front Side Trim 4 Remove screws located on the left and right sides of Removal procedure the control panel 4 Remove screws securing side panel to chassis and 5 Grasp control panel on the far left and right sides and main top gently pull the control panel out and down 5 Open oven door and remove nut securing meat probe receptacle to oven cavity NOTE The electronic control located in the control 6 Label and disconnect wire terminals from receptacle panel is a sensitive item handle gently 7 Gently slide meat probe receptacle through oven 6 Label and disconnect wire terminals cavity 7 Remove infinite switch control knobs infinite 8 R
135. ve warming drawer see Warming Drawer Removal Select Models procedure Place door on a protected surface Remove screws securing front panel to glass panel Remove screws front panel to warming drawer Remove screws securing sliding tracks to warming drawer Reverse procedure to reassemble warming drawer akwh o 2006 Maytag Services 16026923 29 Disassembly Procedures To avoid risk of electrical shock personal injury or A CAUTION death disconnect power and gas before servicing unless testing requires power and or gas Oven Door Warming Drawer Storage Drawer and Access Panel Disassembly Door Lining a Inner Glass Glass Frame d Door Gasket D Su Oven Door Insulation Door Trim and Frame Lower Shield Baffle Door Handle Poor Glass WarmingDrawer Storage Drawer aria Select Models 30 16026923 2006 Maytag Services Appendix The Installation information provided in this service manual is representative of a limited number of models Reference the customer s Installation literature included with the product order a copy if needed or consult Jenn Air s website for the specific model www jennair com 2006 Maytag Services 16026923 A 1 installation Instructions Jenn Air Updraft Cuisini re gaz encastrable circulation ascendante Jenn Air Estufa deslizante a gas de corriente ascendente Jenn Air Installation Instructions Instructions d installation
136. verter cap Cette cuisini re est quip e de gicleurs fixes sur tous les br leurs et d un d tendeur convertible La plaque signal tique de cet appareil indique le r glage fait l usine pour un certain gaz La conversion de l appareil au gaz naturel ou au GPL n cessite le remplacement des t tes de gicleur du four et des t tes de gicleur du br leur sup rieur ainsi que le r glage des obturateurs de br leur du four et du capuchon du convertisseur du d tendeur Esta estufa viene equipada con orificios fijos en todos los quemadores y con un regulador convertible para electrodom sticos La placa de serie de la unidad indica para qu tipo de gas se calibro en la f brica Para convertir la unidad a gas natural o a gas LP es necesario reemplazar las caperuzas de los orificios del horno y los orificios de los quemadores superiores adem s de ajustar los obturadores del quemador del horno y la tapa del convertidor del regulador de presi n del electrodom stico Inlet pressure to the appliance pressure regulator should be as follows for both operation and checking of appliance pressure regulator setting La pression d arriv e au d tendeur de l appareil doit tre la suivante pour le fonctionnement et la v rification du r glage du d tendeur La presi n de entrada al regulador de presi n debe ser la siguiente tanto para el funcionamiento normal como para verificar el ajuste del regulador de presi n Inlet Pressure in inches of water colum
137. with screwdriver Ajustez la hauteur de la flamme avec le tournevis Ajuste la altura de la llama con el destornillador NOTE Double burner only REMARQUE Br leur double uniquement NOTA Quemador doble solamente Adjust double surface burner Light burner and turn to lowest setting where both inner and outer ring are lit Remove knob Ajuster le br leur de surface double Allumez le br leur et r glez le au niveau le plus bas o les deux cercles int rieur et ext rieur sont allum s Retirez le bouton Ajuste el quemador superior doble Encienda el quemador y aj stelo al nivel mas bajo en el que se enciendan los anillos interior y exterior Retire la perilla NOTE For this style of knob the bezel MUST be removed to make the flame adjustments to the Double Burner REMARQUE Pour ce style de bouton la plaque DOIT tre retir e pour effectuer les r glages des flammes du br leur double NOTA Para este tipo de perilla DEBE retirar el marco de la perilla para realizar los ajustes de las llamas del quemador doble CORRECT BON CORRECTO BLUE LIFTING FLAMME BLEUE SE SOULEVANT AZUL QUE SE SEPARA DEL QUEMADOR Verify proper flame height and appearance V rifiez la taille appropri e des flammes et leur apparence Verifique la altura y apariencia correctas de la llama 2006 Maytag Services Insert screwdriver to engage screw Introduisez le tournevis pour tourner la vis Inserte el destornillador Replace

Jenn-Air JGS8860BD Oven User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents