JBL CS1500 Home Theater System User Manual
Contents
1. or if the subwoofer will not be used switch the Master Power switch to the Off position by pressing it until it pops out ve uu cssi0 company N SN 9 1O SUBWOOFER R E TI AUTO ON mn max GREEN ON RED STANDBY POWER A The Phase control determines whether the subwoofers pistonlike action moves in and out in phase with the main speakers or opposite the main speakers There is no correct or incorrect setting Proper phase adjustment depends on several variables such as subwoofer placement and listener position Adjust the Phase switch to maximize bass output at the listening position PHASE o 180 o E o Remember every system room and listener is different There are no right or wrong settings this switch offers the added flexibility to adjust your subwoofer for optimum performance for your specific listening conditions without having to move your speakers If at some time in the future you happen to rearrange your listening room and move your speakers you should experiment with the phase switch in both positions and leave it in the position that maximizes bass performance TROUBLESHOOTING If there is no sound from any of the speakers e Check that receiver amplifier is on and a source is playing e Check that the powered subwoofer is plugged in and is turned on Power switch pushed in e Check all2. CST55 JBL CINEMA SOUND CST55 CSB5 CSC55 CSS10 OWNER S GUIDE READ FIRST CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION To reduce the risk of electric shock do not remove cover or back No user serviceable parts inside Refer servicing to qualified service personnel CAUTION To prevent electric shock do not use this polarized plug with an extension cord receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with a dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of
3. Input LFE preamp level Dimensions H x W x D including feet 464 x 337 x 406mm 18 1 4 x 13 1 4 x 16 Weight 19 5kq 43 Ib Allfeatures and specifications are subject to change without notice Dolby and Pro Logic are registered trademarks of Dolby Laboratories DTS is a registered trademark of DTS Inc The maximum recommended amplifier power rating will ensure proper system headroom to allow for occasional peaks We do not recommend sustained operation at these maximum power levels CSB5 CSC55 and CST55 CSS10 230V only Declaration of Conformity HM PRO SOUND COMES HOME C We Harman Consumer Group International JBL Consumer Products 250 Crossways Park Drive Woodbury NY 11797 USA 2 route de Tours 8500 Balboa Boulevard Northridge CA 91329 USA ee 2 route de Tours 72500 Chateau du Loir France declare in own responsibility that the products described in this owner s manual are in compliance with technical 516 255 4JBL 4525 USA only www jbl com standards 2006 Harman International Industries Incorporated All rights reserved 4 ip It EN 61000 6 3 2001 EN 61000 6 1 2001 JBL and Harman International are registered trademarks and JBL Cinema Sound PolyPlas HeatScape and Pro Sound Comes Home are trademarks of Harman International Industries Incorporated Part No 406 000 05331 E u aurent Rault Harman Consumer Group International Chateau du Loir France 6 06 H A Harman Internationa
4. The CSB5 speakers should be placed at about the same height from the floor as the listeners ears will be or they may be angled toward the listeners The center channel speaker should be placed slightly behind the front left and right speakers and no more than 2 feet 0 6m above or below the tweeters of the left and right speakers It is often convenient to set the center speaker on top of the television set as shown in the drawing The JBL Cinema Sound speaker system may be used in 5 1 6 1 or 7 1 channel applications In 5 1 channel applications two of the surround speakers should be 4 placed slightly behind the listening position and ideally should face each other and be at a level higher than the listeners ears If that is not possible they may be placed against a wall behind the listening position facing forward In 6 1 channel appli cations two of the surround speakers should be placed in the side positions and a single surround back speaker should be placed against the wall behind the listening position In 7 1 channel applications place two of the surround speakers in the side positions and place the two surround back speakers against the rear wall In Dolby Digital and DTS systems it is best to aim all of the speakers except the subwoofer toward the listening position at or slightly above about ear level height In systems where only analog surround processing such as Dolby
5. the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 2 Important Safety Precautions 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 Do not use attachments not recommended by the product manufacturer as they may cause hazards 16 This product should be operated only from the type of power source
6. has been involved in every enjoyment that you expect It enables us to keep you aspect of music and film and that when you think about posted on our latest advance recording and reproduction purchasing additional audio ments and helps us to better from live performances to the equipment for your home car understand our customers recordings you play in your or office you will once again and build products that meet home car or office choose JBL their needs and expectations We re confident that the JBL Please take a moment to JBL Consumer Products system you have chosen will register your product on our INCLUDED Each model sold separately CSC55 CSS10 CST55 2 Wall brackets CSB5 Grille Grille 1 Wall bracket SPEAKER PLACEMENT FRONT SPEAKERS CENTER CHANNEL SPEAKER SUBWOOFER A o 2 ft o o 6m SURROUND SPEAKERS t Single surround back speaker may be used with 6 1 receivers and processors Alternate placement for surround speakers when only 5 1 channels are used required placement for surround back speakers in 7 1 channel systems The front speakers should be placed the same distance from each other as they are from the listening position
7. indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company For products intended to operate from battery power or other sources refer to the operating instructions f an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded so as to provide some ection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antennadischarge unit connection to grounding electrodes and requirements for the grounding electrode See Figure A a S Figure A Example of Antenna Grounding as per National ElectricalCode ANSI NFPA 70 Za 18 An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal 19 Do not overload wall outlets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock 20 Never push
8. objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts which could result in a fire or electric shock Never spill liquid of any kind on the product 21 The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on he apparatus 22 Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 23 When replacement parts are required be sure the service echnician has used replacement parts specified by the manufacturer or that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 24 Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in proper operating condition 25 The product should be mounted to a wall or ceiling only as recommended by the manufacturer Antenna Lead In Wire Ground Clamp Antenna Discharge Unit NEC Section 810 20 Grounding Conductors NEC Section 810 21 Electric Service Equipment Ground Clamps Power Service Grounding Electrode System NEC Art 250 Part H THANK YOU FOR CHOOSING JBL For more than 60 years JBL provide every note of Web site at www jbl com
9. wires and connections between receiver amplifier and speakers Make sure all wires are connected Make sure none of the speaker wires are frayed cut or punctured or touching each other e Review proper operation of your receiver amplifier If there is no sound coming from one speaker e Check the Balance control on your receiver amplifier e Check all wires and connections between receiver amplifier and speakers Make sure all wires are connected Make sure none of the speaker wires are frayed cut or punctured or touching each other In Dolby Digital or DTS modes make sure that the receiver amplifier is configured so that the speaker in question is enabled e Turn off all electronics and switch the speaker in question with one of the other speakers that is working correctly Turn everything back on and determine whether the problem has followed the speaker or has remained in the same channel If the problem is inthe same channel the source of the problem is most likely with your receiver or amplifier and you should consult the owner s manual for that product for further information If the problem has followed the speaker consult your dealer for further assistance or if that is not possible visit www jbl com If there is no sound from the center speaker e Check all wires and connections between receiver amplifier and speaker Make sure all wires are connected Make sure none of the sp
10. Pro Logic Il is available it may be preferable to aim the speakers straight out from the wall to obtain a more diffuse sound The low frequency material reproduced by the subwoofer is mostly omnidirectional and this speaker may be placed in a convenient location in the room However bass reproduction will be maximized when the subwoofer is placed ina corner along the same wall as the front speakers Experiment with subwoofer placement by temporarily placing the subwoofer in the listening position and moving around the room until the bass reproduction is best Place the subwoofer in that location WALL MOUNTING THE CSC55 AND CSB5 The CSC55 center channel and the CSB5 are designed to be mounted on the wall There are two 2 fixed mount wall brackets provided for the CSC55 and one for the CSB5 Each speaker bracket will require up to three 1 1 2 10 wood screws each screw should be fastened to a wall stud lf a wall stud is unavailable install an anchor appropriate for a 1 1 2 10 screw NOTE The customer is responsible for the correct selection and use of mounting hardware available through hardware stores to ensure the proper and safe wall mounting of the speakers Step 1 Using the included mounting template CSC55 only or the bracket back plate CSB5 only mark the positions on the wall where you would like to place the mounting screws Step 2 Attach the back plate s of the bracket to t
11. eaker wires are frayed cut or punctured or touching each other e If your receiver processor is set in Dolby Pro Logic mode make sure the center speaker is not in phantom mode e If your receiver processor is set in one of the Dolby Digital or DTS modes make sure the receiver processor is configured so that the center speaker is enabled If the system plays at low volumes but shuts off as volume is increased e Check all wires and connections between receiver processor and speakers Make sure all wires are connected Make sure none of the speaker wires are frayed cut or punctured or touching each other e If more than one pair of main speakers is being used check the minimum impedance requirements of your receiver amplifier If there is low or no bass output e Make sure the connections to the left and right Speaker Inputs have the correct polarity and e Make sure the subwoofer is plugged into an active electrical outlet and is turned on Power switch pushed in In Dolby Digital or DTS modes make sure your receiver processor is configured so that the subwoofer and LFE output are enabled e Switch the Phase switch to the opposite position and select the position that results in the most pleasing bass response If there is no sound from the surround speakers e Check all wires and connections between receiver processor and speakers Make sure all wires are connect
12. ed Make sure none of the speaker wires are frayed cut or punctured or touching each other e Review proper operation of your receiver amplifier and its surround sound features e Make sure the movie or TV show you are watching is recorded in a surround sound mode If itis not check to see whether your receiver processor has other surround modes you may use In Dolby Digital or DTS modes make sure your receiver processor is configured so that the surround speakers are enabled When five satellites are in use remember to configure your receiver or processor for 6 1 channel operation and when six satellites are in use configure your receiver or processor for 7 1 channels Review the operation of your DVD player and the jacket of your DVD to make sure that the DVD features the desired Dolby Digital or DTS mode and that you have properly selected that mode using both the DVD player s menu and the DVD disc s menu SPECIFICATIONS SYSTEM Frequency Response 27Hz 30kHz 6dB CST55 Maximum Recommended Amplifier Power 150 Watts Power Handling 50W Continuous 300W Peak Frequency Response 55Hz 30kHz 6dB Nominal Impedance 8 Ohms Sensitivity 90dB 1 Watt 1 meter Tweeter One 3 4 19mm titanium laminate dome video shielded Woofers Dual 130mm 5 transducers with PolyPlas cones neodymium magnets and HeatScape motor structure video shielded Dimensions H x W x D including wall
13. he wall using three screws not included Step 3 Attach the front plate s with the two holes of the bracket s to the CSC55 or CSB5 using the provided screws Once positioned properly the speaker should slide down slightly and become secure To remove the speaker from the wall simply slide the speaker up Step 4 Slide the CSC55 or CSB5 speaker with attached bracket front plate s onto the back plate s of the bracket s CSB5 NOTE Remove the base of the CSB5 by removing the two screws on the bottom of the a SPEAKER CONNECTIONS CONNECTION TIPS Separate and strip the ends of the speaker wire as shown Speakers and electronics terminals have corresponding and terminals Most manufacturers of speakers and electronics including JBL use red to denote the terminal and black to denote the terminal The lead of the speaker wire is noted with a stripe It is important to connect both speakers identically on the speaker to on the amplifier and on the speaker to on the amplifier Wiring out of phase results in thin sound weak bass and a poor stereo image With the advent of multichan nel surround sound systems connecting all of the speakers in your system with the correct polarity remains equally important in order to preserve the proper ambience and directionality of the program material CST55 To provide a neater in
14. l Company Declaration of Conformity CC We Harman Consumer Group International 2 route de Tours 72500 Chateau du Loir declare in own responsibility that the product described in this owner s manual is in compliance with technical standards EN 55013 2001 A1 2003 EN 55020 2002 A1 2003 EN 61000 3 2 2000 EN 61000 3 3 1995 A1 2001 EN 60065 2002 Laurent Rault Harman Consumer Group International Chateau du Loir France 6 06
15. mount bracket and grille 1168 x 286 x 286mm 46 x 11 1 4 x 11 1 4 Weight 7 7kg 17 Ib CSB5 Maximum Recommended Amplifier Power 125 Watts Power Handling 40W continuous 300W peak Frequency Response 60Hz 30kHz 6dB Nominal Impedance 8 Ohms Sensitivity 88dB 1 watt 1 meter Tweeter 3 4 19mm Titanium laminate dome video shielded Woofer 5 130mm Transducer with PolyPlas cone neodymium magnet and HeatScape motor structure video shielded Dimensions H x W x D including base and grille 363 x 155 x 116mm 14 5 16 x 6 1 8 x 4 9 16 Weight 2 3kg 5 Ib Dimensions H x W x D without base and with wall mount bracket and grille 338 x 155 x 130mm 13 5 16 x 6 1 8 x 5 1 8 Weight 2kg 4 5 Ib CSC55 Maximum Recommended Amplifier Power 150 Watts Power Handling 50W Continuous 300W Peak Frequency Response 55Hz 30kHz 6dB Nominal Impedance 8 Ohms Sensitivity 90dB 1 watt 1 meter Tweeter One 19mm 3 4 titanium laminate dome video shielded Woofers Dual 130mm 5 transducers with PolyPlas cones neodymium magnets and HeatScape motor structure video shielded Dimensions H x W x D including wall mount bracket and grille 159 x 667 x 108mm 6 1 4 x 26 1 4 x 4 1 4 Weight 4 5kg 10 Ib CSS10 Amplifier Power 150 Watts RMS Frequency Response 27Hz Low pass crossover setting at signal source Low Frequency Driver 250mm 10 cone and HeatScape motor structure video shielded
16. nnect this jack to the LFE output or subwoofer output on your receiver or amplifier Connect each speaker to the corresponding speaker terminals on your receiver or amplifier Make sure that you have configured your surround sound processor for Sub woofer On Also configure your receiver for 5 1 6 1 or 7 1 channel operation as appropriate The front left front right center and rear speakers should all be set to Small If your receiver allows you to set the cross over frequency between the subwoofer and the main speakers select 100Hz or the setting that is the closest frequency below it DOLBY PRO LOGIC NON DIGITAL LINE LEVEL Use this installation method for Dolby Pro Logic applications not Dolby Digital DTS or other digital processing where the receiver processor is equipped with a subwoofer output or a volumecontrolled preamp line level output Left Front Center Subwoofer Use RCA type interconnects to connectthe line level subwoofer outputs on your receiver or amplifier to the line level inputs on the subwoofer IMPORTANT Do not use the LFE input on the subwoofer with Dolby Pro Logic processors Right Front Line Level In O Receiver Out Center Subwoofer Right Front Left Surround Back Surround Back Right Surround Left Right Surround 9 Posie e Ge Surround Back Surr
17. ound Back a Left Surround Left Right Right Surround NOTE If your receiver or amplifier has only one subwoofer output jack then you will need to use a Y connector not included Plug the male end of the Y connector into your receiver or amplifier s subwoofer output jack and connect each of the two female ends to separate RCA type interconnects Finally plug the RCA type interconnects into the line level inputs on the subwoofer Connect each speaker to the corresponding speaker terminals on your receiver or amplifier Make sure your receiver or processor is correctly configured to indicate that the subwoofer is On SUBWOOFER OPERATION Press the Master Power switch marked Power to the On position to use the subwoofer The CSS10 subwoofer will automatically turn on or go into standby sleep mode as described below When your receiver or amplifier is off or is not sending program material to the subwoofer the subwoofer will be in standby mode the LED on the front of the CSS10 will be red When the subwoofer senses an audio signal it will automatically turn on the LED will be green If the subwoofer does not sense a signal after approximately 20 minutes it will automatically go into standby mode If you will be away from home for an extended period of time VOLUME 9 D Volume may be adjusted using the Subwoofer Level control as shown
18. stalla tion the CST55 allows you to insert the speaker wires through holes in the base Simply separate and strip the wires as described above loosen the terminals and insert each wire into its corresponding hole in the base Then tighten down the terminals iel The hole in the center of each collar is intended for use with banana type connectors To comply with European CE certification these holes are blocked with plastic inserts at the point of manufacture To use banana type connectors requires the removal of the inserts CSB5 CSC55 To use the binding post speaker terminals unscrew the colored collar until the pass through hole in the center post is visible under the collar Insert the bare end of the wire through this hole then screw the collar down until the connection is tight The hole in the center of each collar is intended for use with banana type connectors To comply with European CE certification these holes are blocked with plastic inserts at the point of manufacture To use banana type connectors requires the removal of the inserts DOLBY DIGITAL OR DTS OR OTHER DIGITAL SURROUND MODE CONNECTION RECEIVER SUBWOOFER L LFE OUT LINE LFE LEVEL IN R Use this installation method for Dolby Digital DTS or other digital surround processors Use the line level input jack marked LFE for the Low Frequency Effects channel Co
Download Pdf Manuals
Related Search