Indesit IWDE126 Washer User Manual
Contents
1. Door Mounting Accessories Fig 1 2 3 4 5 N 2 Hinge Supports N 2 Hinges Fig 1 Fig 2 Q Q N 1 Magnet N 1 Magnet plate Fig 3 Fig 4 JO O N 1 Rubber plug N 4 Spacers Fig 5 Fig 4 B No 6 type A self threading screws 13 mm No 2 type B metric countersunk screws 25 for fastening the magnet plate to the cabinet No 4 type C metric screws 15 mm for mounting the hinge supports to the cabinet No 4 type D metric screws 7 mm for mounting the hinges on the supports Mounting the Parts onto the Face of the Machine Fit the hinge supports to the appliance front panel positioning the hole marked with an arrow in fig 7 so that it is on the inner side of the front panel Fit a spacer fig 4 B between the surfaces using type C screws Fit the magnet plate at the top of the opposite side using type B screws to fix two spacers fig 4 B between the plate and the surface 1 InpesiT Using the Drilling Template To trace the positions of the holes on the left hand side of the panel align the drilling template to the top left side of the panel using the lines traced on the extremities as a reference To trace the positions of the holes on the right hand side of the panel align the drilling template to the top right side of the panel Use an appropriately sized router to mill the holes for the two hing2. see page 11 5 Set the drying cycle if necessary see page 11 Programme table When the programme is finished the ON OFF DOOR LOCK Led will flash to indicate that the appliance door can be opened Take out your laundry and leave the appliance door ajar to allow the drum to dry thoroughly Turn the Washer dryer off by pressing button 1 Detergent Cycle Type of fabric and Tempe Drying Fabric Losi degree of soil Program ratre Cycle Ss oftoner length Description of wash cycle pre wash minutes wash Standard White prewash Extremely soiled 4 90 C P r A 3 155 Pre wash wash cycle rinse cycles whites sheets tablecloths etc intermediate and final spin cycles White Cotton Extremely soiled o 90 C R i A 150 Wash cycle rinse cycles whites sheets tablecloths etc intermediate and final spin cycles eo 2 coc 140 intermediate and final spin cycles White Cotton Heavily soiled whites o 40 C 3 _ i x 125 Wash cycle rinse cycles and delicate colours intermediate and final spin cycles Colour Cotton Slightly soiled whites and 3 40 C _ i 1 85 Wash cycle rinse cycles delicate colours shirts jumpers etc intermediate and final spin cycles fee Ue eee ee i ie ea ii Wool 5 40 C g g i n 50 Wash cycle rinse cyclese
3. General There will always be some motor pump and drum noise during spin Out of Balance detected when attempting to go into a spin cycle If this happens the machine will continue to try to repeat the distribution of the load required before the machine will go into higher spin speeds This will increase the programme time accordingly This is a safety feature to prevent damage Out of Balance can be caused by washing a single heavy item eg duvet quilt etc Try the programme again using a different load The dispenser drawer is blocked with detergent and requires cleaning The water pressure is too high and requires turning down turn down the tap on the water supply pipe slightly and try again The machine is tilting forwards It must be level when in its final position The fill hose is loose check both the cabinet and tap ends The fill hose is tight but still leaks if so replace the rubber washers or the fill hose is missing the rubber washer The drain hose is not fixed in properly Switch off the machine and unplug it wait for approximately 1 minute and then switch it back on again If the problem persists contact the Technical Assistance Service The machine requires a service wash Run a 90 degree wash cycle with detergent and no laundry The door will not open until the door lock indicator light goes out shortly after the program has finished The door seal has drainage holes at the bottom This is normal
4. The water level is correct if it can be seen at the bottom of the door The detergent is not suitable for machine washing it should display the text for washing machines or hand and machine wash or the like To comply with new energy saving regulations the machine is fitted with an automatic standby system Press ON OFF button for 3 seconds to activate the machine it can then either be switched off or a new programme selected Your washing machine contains sensors that monitor progress during the wash cycle eg Water Levels Temperatures Out of Balance loads Wash time progress Normally if your machine successfully completes the cycle there is unlikely to be anything wrong Remember you will be charged for a service call for problems caused by incorrect installation as listed above Not emptying contents from pockets may cause pump or drain blockages or may damage the machine Do not wash items which do not have a wash label or wash items that are not intended as machine washable 16 Assistance 12 Months Parts and Labour Guarantee Your appliance has the benefit of our manufacturer s guarantee which covers the cost of breakdown repairs for twelve months from the date of purchase This gives you the reassurance that if within that time your appliance is proven to be defective because of either workmanship or materials we will at our discretion either repair or replace the appliance at no cost to yo
5. delicate spin cycle Silk Very delicate fabrics 6 30 C i _ i A 45 Wash cycle rinse cycles anti curtains silk viscose etc crease or draining cycle Drying cotton 7 Drying delicates 8 Time 4 you Flesh Clean Heavily soiled whites 9 60 C _ i z 60 Wash cycle rinse cycles and fast colours intermediate and final spin cycles Flesh Nylon Delicate colours 10 40 C E i e 40 Wash cycle rinse cycles delicate all types of slightly soiled garments spin cycle Daily Delicate colours 11 30 C e _ z e 30 Wash cycle rinse cycles and all types of slightly soiled garments delicate spin cycle Sport Sports Shoes MAX 2 pairs 12 30 C e 50 occu eo tE wash cycle rinse cycles and delicate spin cycle Special Sport Fabrics for 13 30 C i _ E 60 Wash cycle rinse cycles sportswear Tracksuits shorts etc intermediate and final spin cycles PARTIAL PROGRAMMES Rinse Ey e e Rinse cycles and spin cycle Spin e Draining and spin cycle Drain tg Drain Notes For programme 9 we advise against exceeding a wash load of 3 5 kg For programme 13 we advise against exceeding a wash load of 2 kg For the anti crease function see Easy iron opposite page The information contained in the table is purely indicative Special programme Daily programme 11 for Synthetics is designed to wash lightly soiled garments in a short amount of time it only lasts 30 minutes and allows you to
6. only cycle Repeat this procedure for the remainder of the load Dry only Turn the PROGRAMME knob to one of the drying settings 7 8 depending on the type of fabric then select the desired drying type using the DRYING knob Important A spin cycle is carried out during the drying if you have set a cotton programme and a level of dryness Cupboard 7 Hanger 7 Iron lt 2 For cotton loads of less than 1 Kg use the drying programme designed for delicate fabrics Functions To enable a function 1 press the button corresponding to the desired function according to the table below 2 the function is enabled when the corresponding button is illuminated Note The rapid flashing of the button indicates that the corresponding function cannot be selected for the programme set fabrics making them easier to iron symbol and press the START RESET button If you also want to run the drying cycle this button is enabled Enabled with Function Effect Comments programmes __ Press the button repeatedly until the LED corresponding to the Oi Delays the start desired delay is turned on of the wash by The fifth time the button is pressed the function will be disabled All up to 9 hours N B Once you have pressed the Start Reset button the delay Delay Timer can only be decreased if you wish to modify it When this function is set programmes 4 6 will end with the This option laundry left to soak Anti crease and
7. save on both time and energy By setting this programme 11 at 30 C you can wash different fabrics together except for woollen and silk items with a maximum load of 3 kg We recommend the use of liquid detergent 1 InpesiT Personalisations 1 Setting the temperature Turn the TEMPERATURE knob to set the wash temperature see Programme table on page 10 The temperature can be lowered or even set to a cold wash 3 e The data contained in the Table of drying times table are purely indicative Fabric Load type Max 7 sa type load dai kg Cup Hanger Iron board Cotton Clothing of different sizes Linen 5 180 170 140 X lt Set the drying cycle Turn the DRYING knob to set the desired drying type Two options are available A Based on time From 40 minutes to 180 B Based on the damp level of the dry clothes lron slightly damp clothes easy to iron Hanger 7 dry clothes to put away Cupboard very dry clothes recommended for towelling and bathrobes Terry towels Terital Sheets Shirts Cotton 25 140 120 100 rm see o e E pe A cooling stage is foreseen at the end of the drying cycle If your laundry load to wash and dry is exceptionally in excess of the maximum load foreseen see table opposite perform the wash cycle and when the programme is complete divide up the garments and put part of them back in the drum Now follow the instructions provided for a dry
8. the Rinse cycle phase reduces the LED Y will flash ES amount of to conclude the cycle press the START RESET button 3 4 6 creasing on to run the draining cycle alone set the knob to the relative 9 10 Rinse cycle Easy iron only if combined with level Z Iron 6 6 Ey i i Recommended when the appliance has a full load or with large 16 15 a Extra Rinse rinse quantities of detergent Rinse cycle All Reduces the ies trata Spin speed 7 8 and i 1200 600 draining 11 Detergents and laundry Detergent dispenser Good washing results also depend on the correct dose of detergent adding too much detergent won t necessarily make for a more efficient wash and may in fact cause build up on the interior of your appliance and even pollute the environment Open up the detergent dispenser and pour in the detergent and fabric softener as follows compartment 1 Detergent for pre wash powder compartment 2 Detergent for the wash cycle powder or liquid Liquid detergent should only be poured in immediately prior to the wash cycle start compartment 3 Additives fabric softeners etc The fabric softener should not overflow from the grid Do not use hand wash detergent because it may form too much foam Preparing your laundry e Divide your laundry according to the type of fabric the symbol on the label the colours separate coloured garments from whites e Empty al
9. How to connect an alternative plug The wires in this mains lead are coloured in accordance with the following code BLUE NEUTRAL N BROWN LIVE L GREEN amp YELLOW EARTH E Disposing of the appliance When disposing of the appliance please remove the plug by cutting the mains cable as close as possible to the plug body and dispose of it as described above GREEN amp YELLOW Mi m BROWN 2 FLL 13 ampere fuse Fee an CROSS BAR CORD GRIP BLUE The washer dryer should not be installed in an outdoor environment not even when the area is sheltered because it may be very dangerous to leave it exposed to rain and thunderstorms When the washer dryer is installed the mains socket must be within easy reach Do not use extensions or multiple sockets The power supply cable must never be bent or dangerously compressed The power supply cable must only be replaced by an authorised serviceman Warning The company denies all liability if and when these norms are not respected The first wash cycle Once the appliance has been installed and before you use it for the first time run a wash cycle with detergent and no laundry setting the 90 C programme without a pre wash cycle 1 Inpesit Technical details Model IWDE 126 59 5 cm wide Dimensions 81 5 cm high 54 5 cm deep Capacity from 1 to 6 kg for the wash programme from 1 to 5 kg for the d
10. Instructions for use WASHER DRYER This symbol reminds you to read this instruction manual English 1 Contents Installation 2 3 4 5 6 7 Unpacking and levelling Electric and water connections The first wash cycle Technical details Instructions for the fitter Washer dryer description 8 9 Control pane Leds Starting and Programmes 10 Briefly how to start a programme IWDE 126 Programme table Personalisations 11 Setting the temperature Setting the drying cycle Functions Detergents and laundry 12 Detergent dispenser Preparing your laundry Special items Precautions and advice 13 General safety Disposal Saving energy and respecting the environment Care and maintenance 14 Cutting off the water or electricity supply Cleaning your appliance Cleaning the detergent dispenser Caring for your appliance door and drum Cleaning the pump Checking the water inlet hose Troubleshooting 15 16 Assistance 17 18 1 InDesIT installation Keep this instruction manual in a safe place for future reference Should the appliance be sold transferred or moved make sure the instruction manual accompanies the washer dryer to inform the new owner as to its operation and features Read these instructions carefully they contain vital information on installation use and safety Unpacking and levelling Unpacking 1 Unpack the washer dryer 2 Check whether the washer dryer has been
11. damaged during transport If this is the case do not install it and contact your retailer 3 Remove the 4 protective screws and the rubber bush with the respective spacer situated on the rear of the appliance see also the installation leaflet 4 Seal the gaps using the plastic plugs provided 5 Keep all the parts you will need them again if the washer dryer needs to be moved to another location Packaging materials are not children s toys Levelling Your machine may make a considerable amount of noise if the two front feet have not been adjusted correctly 1 Install the washer dryer on a flat sturdy floor without resting it up against walls furniture cabinets or other 2 If the floor is not perfectly level compen sate for any unevenness by tightening or loosening the adjustable front feet see figure the angle of inclination measured according to the worktop must not exceed 2 Levelling your appliance correctly will provide it with stability and avoid any vibrations noise and shifting during operation If it is placed on a fitted or loose carpet adjust the feet in such a way as to allow enough room for ventilation beneath the washer dryer Electric and water connections Connecting the water inlet hose 1 Connect the supply pipe by screwing it to a cold water tab using a 3 4 gas threaded connection see figure Before performing the connection allow the water to run freely until it
12. dpipe that the end does not go down more than 15cms 6 inches If the hose is pushed down too far this may cause the machine to self syphon ie continuously empty as it is filling Electric connection Before plugging the appliance into the mains socket make sure that e the socket is earthed and in compliance with the applicable law e the socket is able to sustain the appliance s maximum power load indicated in the Technical details table see page 5 e the supply voltage is included within the values ndicated on the Technical details table see page 5 e the socket is compatible with the washing machine s plug If this is not the case replace the socket or the plug Your appliance is now supplied with a 13 amp fused plug it can be plugged into a 13 amp socket for immediate use Before using the appliance please read the instructions below WARNING THIS APPLIANCE MUST BE EARTHED THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN Replacing the fuse When replacing a faulty fuse a 13 amp ASTA approved fuse to BS 1362 should always be used and the fuse cover re fitted If the fuse cover is lost the plug must not be used until a replacement is obtained Replacement fuse covers If a replacement fuse cover is fitted it must be of the correct colour as indicated by the coloured marking or the colour that is embossed in words on the base of the plug Replacements can be obtained dir
13. ectly from your nearest Service Depot Removing the plug If your appliance has a non rewireable moulded plug and you should wish to re route the mains cable through partitions units etc please ensure that either the plug is replaced by a fused 13 ampere re wearable plug bearing the BSI mark of approval Or the mains cable is wired directly into a 13 amp cable outlet controlled by a switch in compliance with BS 5733 which is accessible without moving the appliance Disposing of the plug Ensure that before disposing of the plug itself you make the pins unusable so that it cannot be accidentally inserted into a socket Instructions for connecting cable to an alternative plug Important the wires in the mains lead are coloured in accordance with the following code Green amp Yellow Earth Blue Neutral Brown Live As the colours of the wires in the lead may not correspond with the coloured markings identifyng the terminals in your plug proceed as follows Connect Green amp Yellow wire to terminal marked E Or or coloured Green or Green amp Yellow Connect Brown wire to terminal marked L or coloured Red Connect Blue wire to terminal marked N or coloured Black If a 13 amp plug BS 1363 is used it must be fitted with a 13 amp fuse either in the plug or adaptor or at the distribution board If you are in any doubt the electrical supply to your machine consult a qualified electrician before use
14. egradable detergents do contain ingredients that alter the natural balance of the environment In addition avoid using fabric softener as much as possible e f you use your washing machine from late in the afternoon until the early hours of the morning you will helo reduce the electricity board s peak load The Delay Timer option see page 23 helps to organise your wash cycles accordingly e lf your laundry has to be dried in a tumble dryer select a high spin speed Having the least water possible in your laundry will save you time and energy in the drying process 13 Care and maintenance Cutting off the water or electricity supply e Turn off the water tap after every wash This will limit the wear of your appliance s water system and also prevent leaks e Unplug your appliance when cleaning it and during all maintenance operations Cleaning your appliance The exterior and rubber parts of your appliance can be cleaned with a soft cloth soaked in lukewarm soapy water Do not use solvents or abrasives Cleaning the detergent dispenser Remove the dispenser by raising it and pulling it out see figure Wash it under running water this operation should be repeated frequently Caring for your appliance door and drum e Always leave the appliance door ajar to prevent unpleasant odours from forming Cleaning the pump The Washer dryer is fitted with a self cleaning pump that does not require any maintena
15. es the rubber plug and the magnet Mounding the Parts onto the Wooden Panel Door Insert the hinges into the holes the movable part of the hinge must be positioned facing away from the panel and fasten them with the 4 type A screws Insert the magnet into the top hole on the opposite side of the hinges and fasten it with the two type B screws Insert the rubber plug into the bottom hole The panel is now ready to be mounted onto the machine Mounting the Panel into the machine Insert the nib of the hinge indicated by the arrow in fig 2 into the hole for the hinge and push the panel towards the front of the machine Fasten the two hinges with the type D screws Fastening the plinth guide If the machine is installed at the end of a set of modular cabinets mount either one or both of the guides for the base molding as shown in fig 8 Adjust them for depth based on the position of the base molding and if necessary fasten the base to the guides fig 9 This is how to assemble the plinth guide fig 8 Fasten angle P using screw R insert plinth guide Q into the special slot and once it is in the desired position lock it in place using angle P and screw R Inserting the machine into the Cabinet Push the machine into the opening aligning it with the cabinets fig 6 Regulate the adjustable feet to raise the machine to the appropriate height To adjust the position of the wooden panel in both the ver
16. fly and wait for the machine to start up again Note to avoid excessive vibrations before every spin cycle the machine distributes the load in a uniform manner by continuously rotating the drum at a speed which is slightly faster than the normal washing speed When despite repeated attempts the load is still not evenly distributed the machine spins at a lower speed than the set frequency If the load is excessively unbalanced the machine attempts to distribute it instead of spinning The balancing attempts may extend the total duration of the cycle up to a maximum of 10 minutes 1 InpesiT Leds The LEDS provide important information This is what they can tell you Delay set If the Delay Timer function has been enabled see page 11 once you have started the programme the LED corresponding to the delay set will begin to flash E gt 2h EYE 4h gt 6h O oh As time passes the remaining delay will be displayed and the corresponding LED will flash E 2h yy gt 4h 6h O D gt m Once the set delay is complete the flashing LED will turn off and the programme set will start 1 ON OFF DOOR LOCK led Cycle phase under way During the wash cycle the LEDs gradually illumina te on to indicate the cycle phase under way E9 Prewash Wash EJ Rinse gt Spin cycle O Drying Note during draining the LED corresponding to the Spin cycle phase will be turned on
17. ight Insert the strip as follows loosen the three screws N situated at the front of the Top cover of the appliance insert strip M as shown in fig 72 then fasten screws N d i Washer dryer description Control panel Detergent dispenser Detergent dispenser to add detergent and fabric softener see page 12 LEDS to find out which wash cycle phase is under way If the Delay Timer function has been set the time left until the programme starts will be indicated see page 9 DRYING knob to set the desired drying cycle see page 11 FUNCTION buttons to select the functions available The button corresponding to the function selected will remain on TEMPERATURE knob to set the temperature or the cold wash cycle see page 11 Leds stone TS ON OFF Button OOOO Orc 000 0 DRYING via START RESET Button TEMPERATURE Knob START RESET button to start the programmes or cancel any incorrect settings ON OFF DOOR LOCK Led to find out whether the Washer dryer is on and if the appliance door can be opened see page 9 ON OFF button to turn the Washer dryer on and off PROGRAMME knob to select the wash programmes The knob stays still during the cycle Standby mode This washing machine in compliance with new energy saving regulations is fitted with an automatic standby system which is enabled after about 30 minutes if no activity is detected Press the ON OFF button brie
18. is perfectly clear 2 Connect the other end of the water inlet hose to the washer dryer screwing it onto the appliance s cold water inlet situated on the top right hand side on the rear of the appliance see figure 3 Make sure there are no kinks or bends in the hose The water pressure at the tap must be within the values indicated in the Technical details table on the next page If the water inlet hose is not long enough contact a specialist store or an authorised serviceman Ensure that the supply taps are allowing water through Old taps may seize in the closed position and thus prevent water reaching the machine 1 InpesiT Connecting the drain hose Connect the drain hose without bending it to a draining duct or a wall drain situated between 65 and 100 cm from the floor The drain hose may be connected to an under sink trap Before connecting the drain hose from the machine ensure that any blanks or removable ends have been taken off the spigot Where it connects to the waste water pipe cut end off spigot or remove the blanking cap If it is place over the edge of a basin or sink be sure the free end of the hose should not be underwater We advise against the use of hose extensions in case of absolute need the extension must have the same diameter as the original hose and must not exceed 150 cm in length Ensure that if the drain hose is pushed into a stan
19. l pockets and check for loose buttons e Do not exceed the weight limits stated below which refer to the weight when dry Sturdy fabrics max 6 kg synthetic fabrics max 2 5 kg Delicate fabrics max 2 kg Wool max 1 5 kg How much does your laundry weigh 1 sheet 400 500 g 1 pillow case 150 200 g 1 tablecloth 400 500 g 1 bathrobe 900 1200 g 1 towel 150 250 g 12 Special items Curtains fold curtains and place them in a pillow case or mesh bag Wash them separately without exceeding half the appliance load Use programme 6 which excludes the spin cycle automatically Quilted coats and windbreakers if they are padded with goose or duck down they can be machine washed Turn the garments inside out and load a maximum of 2 3 kg repeating the rinse cycle once or twice and using the delicate spin cycle Wool for best results use a specific detergent taking care not to exceed a load of 1 5 kg Precautions and advice 1 invesit The Washer dryer was designed and built in compliance with the applicable international safety regulations The following information is provided for your safety and should consequently be read carefully General safety e This appliance has been designed for non rofessional household use and its functions must not be changed e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unles
20. n hose e The Pump filter is blocked e The Easy iron function is enabled to complete the programme press the START RESET button see page 11 e The drain hose is kinked e New Installation The blanking cap or spigot has not been removed if connected under a sink e The drain hose or sink trap is blocked e Programme times will vary due to water pressure the incoming water temperature and if the wash load goes out of balance This will increase the programme times accordingly see The machine wont spin properly below Most Common Causel e The feet have not been adjusted enabling the machine to rock e New Installation Either the Transit Bolts including the plastic spacers or the Polystyrene Packaging have not been removed when installing the machine e The machine is trapped between cabinets and or walls e The load is in a slight out of balance condition and machine is spinning but at a lower speed 15 The machine is noisy The machine wont spin properly The machine leaks from the dispenser The machine leaks other than dispenser The indicator lights on the console are flashing rapidly The machine smells The machine door cannot be opened Door Seal damaged at the bottom The water level is too low when the machine is washing There is too much foam After completing the programme or before starting a programme the machine has turned itself off no lights
21. n human health and the environment The crossed out wheeled bin symbol on the product reminds you of your obligation that when you dispose of the appliance it must be separately collected Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance Saving energy and respecting the environment Environmentally friendly technology If you only see a little water through your appliance door this is because thanks to the latest Indesit technology your washing machine only needs less than half the amount of water to get the best results an objective reached to respect the environment Saving on detergent water energy and time e To avoid wasting resources the Washer dryer should be used with a full load A full load instead of two half loads allows you to save up to 50 on energy e The pre wash cycle is only necessary on extremely soiled garments Avoiding it will save on detergent time water and between 5 and 15 energy e Treating stains with a stain remover or leaving them to soak before washing will cut down the need to wash them at high temperatures A programme at 60 C instead of 90 C or one at 40 C instead of 60 C will save up to 50 on energy e Use the correct quantity of detergent depending on the water hardness how soiled the garments are and the amount of laundry you have to avoid wastage and to protect the environment despite being biod
22. nce Sometimes small items Such as coins or buttons may fall into the pre chamber that protects the pump situated in the lower part of the same Make sure the wash cycle has ended and unplug the appliance To access the pre chamber 1 unscrew the lid rotating it anti clockwise see figure a little water may trickle out This is perfectly normal 2 clean the interior thoroughly 3 screw the lid back on 14 Checking the water inlet hose Check the water inlet hose at least once a year If you see any cracks replace it immediately during the wash cycles water pressure is very strong and a cracked hose could easily split open Never use hoses that have already been used Troubleshooting 1 inpesit Your Washer dryer could fail to work Before calling for Assistance see page 16 make sure the problem can t easily be solved by consulting the following list Problem The machine does not switch on The wash cycle does not start The machine does not dry The clothes are too hot when the drying cycle is finished The machine does not fill with water or The first wash cycle stage indicator light flashes The machine continuously fills with water and continually drains away or Water left in the dru or Stuck on wash The machine does not drain or spin The programme takes too long The machine vibrates a lot during the spin cycle Possible causes Solution e The appliance is n
23. ngineer s time To activate the extra parts warranty on your appliance simply call our registration line on 08448 24 24 24 Republic of Ireland 01 230 0800 Extended Guarantees We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair bills for the life of your policy To find the ideal plan for you please call our advice line on 08448 226 226 Republic of Ireland 01 230 0233 Free Helpdesk Service We have a dedicated team who can provide free advice and assistance with your appliance if you experience any technical difficulties within the first 90 days of ownership Simply call our Indesit Service Hotline on 08448 224 224 Republic of Ireland 0818 313 413 for telephone assistance or where necessary to arrange for an engineer to call 17 After Sales Service No one is better placed to care for your Indesit appliance during the course of its working life than us the manufacturer Essential Contact Information Indesit Service We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1100 fully qualified engineers on call to ensure you receive fast reliable local service UK 08448 224 224 Republic of Ireland 0818 313 413 www indesitservice co uk Please note Our advisors will require the following information Parts and Accessories We supply a full range of genuine replacement parts as well as accessory products
24. ot plugged into the socket fully or not enough to make contact e There is no power to the socket or the fuse has blown in the mains plug e The door is not closed properly e The ON OFF button has not been pressed e The START RESET button has not been pressed e The water tap has not been turned on to allow water to flow into the machine e A delayed start has been set e Check the 2 sections above e The DRY button has been pressed to exclude drying e A cooling down period is always added to the end of each drying cycle If the clothes appear too hot to handle leave the door open to allow to cool further before removing from the machine e The water inlet hose is kinked e The water inlet hose is not connected to the water supply e The water pressure is too low e The water tap has not been turned on to allow water to flow into the machine e There is no water supply to the house e The inlet valve filter is blocked e The START RESET button has not been pressed e The top of the drain hose is too low It must be fitted at a height between 65 and 100 cm from the floor e The drain hose is connected incorrectly to the sink trap allowing water to run into the machine the drain hose must be positioned higher than the bottom of the sink to prevent water flowing down the drain hose e The end of the drain hose has been pushed too far down the standpipe the U bracket should be fitted 100 mm from the end of the drai
25. rying programme Electric connections please refer to the technical data plate fixed to the machine Water connections maximum pressure 1 MPa 10 bar minimum pressure 0 05 MPa 0 5 bar drum capacity 52 litres Spin speed up to 1200 rpm Wash programme 2 temperature 60 C Control run with a load of 6 kg pepe cane Drying first drying cycle performed with Li ib a 1 kg load by selecting a drying time of EN 50229 A directiva Second drying cycle performed with a 5 kg load and the DRYING knob on the setting Ezi This appliance is compliant with the following European Community Directives 2004 108 CE Electromagnetic Compatibility 2002 96 CE 2006 95 CE Low Voltage Instructions for the fitter Mounting the wooden panel onto the door and inserting the machine into cabinets In the case where the machine must be shipped for final installation after the wooden panel has been mounted we suggest leaving it in its original packaging The packaging was designed to make it possible to mount the wooden panel onto the machine without removing it completely see figures below The wooden panel that covers the face of the machine must not be less than 18 mm in thickness and can be hinged on either the right or left For the sake of practicality when using the machine we recommend that the panel be hinged on the same side as the door for the machine itself the left
26. s they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance Do not dry unwashed items in the tumble dryer Items that have been soiled with substances such as cooking oil acetone alcohol petrol kerosene spot removers turpentine waxes and wax removers should be washed in hot water with an extra amount of detergent before being dried in the tumble dryer Items such as foam rubber latex foam shower caps waterproof textiles rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the tumble dryer Fabric softeners or similar products should be used as specified by the fabric softener instructions The final part of a tumble dryer cycle occurs without heat cool down cycle to ensure that the items are left at a temperature that ensures that the items will not be damaged WARNING Never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated e Never touch the washing machine when barefoot or with wet or damp hands or feet e Do not pull on the power supply cable to unplug the appliance from the electricity socket Pull the plug out yourself e Do not open the detergent dispenser while the appliance is in operation e Do not touch the drain water as i
27. t could reach very high temperatures e Never force the washing machine door this could damage the safety lock mechanism designed to prevent any accidental openings e Inthe event of a malfunction do not under any circumstances touch internal parts in order to attempt repairs e Always keep children well away from the appliance while in operation e The appliance door tends to get quite hot during the wash cycle e Should it have to be moved proceed with the help of two or three people and handle it with the utmost care Never try to do this alone because the appliance is very heavy e Before loading your laundry into the washing machine make sure the drum is empty e During the drying phase the door tends to get quite hot e Do not use the appliance to dry clothes that have been washed with flammable solvents e g trichlorethylene e Do not use the appliance to dry foam rubber or similar elastomers e Make sure that the water tap is turned on during the drying cycles Disposal e Disposing of the packaging material observe local regulations so the packaging can be re used e The European Directive 2002 96 EC on Waste Electrical and Electronic Equipment requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact o
28. that protect and hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life UK 08448 225 225 Republic of Ireland 0818 313 413 www indesitservice co uk Appliance Registration We want to give you additional benefits of Indesit ownership To activate your free 5 year parts guarantee you must register your appliance with us UK 08448 24 24 24 Republic of Ireland 01 230 0800 www indesitservice co uk Indesit Company UK Ltd Morley Way Peterborough PE2 9JB Indesit Company Unit 49 Airways Industrial Estate Dublin 17 LA e Recycling Disposal Information As part of Indesit s continued commitment to helping the environment Indesit reserves the right to use quality recycled components to keep down customer costs and minimise material wastage Please dispose of packaging and old appliances carefully To minimise the risk of injury to children remove the door plug and cut the mains cable off flush with the appliance Dispose of these parts separately to ensure that the appliance can no longer be plugged into a mains socket and the door cannot be locked shut 18 19 195082478 01 04 2010 Xerox Fabriano 20
29. tical and horizontal directions use the C and D screws as shown in fig 7 Important close the lower part of the appliance front by ensuring that the plinth rests against the floor Fig 7 Fig 9 Accessories provided for the height adjustment The following can be found inside the polystyrene lid fig 70 2 crossbars G 1 strip M the following can be found inside the appliance drum 4 additional feet H 4 screws I 4 screws R 4 nuts L Fig 10 Adjusting the appliance height The height of the appliance can be adjusted from 815 mm to 835 mm by turning the 4 feet Should you require the appliance to be placed higher than the above height you need to use the following accessories to raise it to up to 870 mm the two crossbars G the 4 feet H the 4 screws I the 4 nuts L then perform the following operations fig 11 remove the 4 original feet place a crossbar G at the front of the appliance fastening it in place using screws I screwing them in where the original feet were then insert the new feet H Repeat the same operation at the back of the appliance Now adjust feet H to raise or lower the appliance from 835 mm to 870 mm Once you have reached the desired height lock nuts L onto crossbar G To adjust the appliance to a height between 870 mm and 900 mm you need to mount strip M adjusting feet H to the required he
30. u This guarantee is subject to the following conditions The appliance has been installed and operated correctly and in accordance with our operating and maintenance instructions The appliance is used only on the electricity or gas supply printed on the rating plate The appliance has been used for normal domestic purposes only The appliance has not been altered serviced maintained dismantled or otherwise interfered with by any person not authorised by us Any repair work must be undertaken by us or our appointed agent Any parts removed during repair work or any appliance that is replaced become our property The appliance is used in the United Kingdom or Republic of Ireland The guarantee does not cover Damage resulting from transportation improper use neglect or interference or as a result of improper installation Replacement of any consumable item or accessory These include but are not limited to plugs cables batteries light bulbs fluorescent tubes and starters covers and filters Replacement of any removable parts made of glass or plastic THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON DOMESTIC PREMISES 5 Year Parts Guarantee Indesit also offers you a free 5 year parts guarantee This additional guarantee is conditional on you registering your appliance with us and the parts being fitted by one of our authorised engineers There will be a charge for our e
31. when the drying cycle is complete the indicator light relative to phase Of will flash to indicate that the DRYING knob needs to be set back to the 0 setting Function buttons The FUNCTION BUTTONS also act like LEDS When a function is selected the corresponding button is illuminated If the function selected is incompatible with the programme set the button will flash and the function will not be enabled If you set a function that is incompatible with another function you selected previously only the last one selected will be enabled If this LED is on the appliance door is locked to prevent it from being opened accidentally to avoid any damages wait for the LED to flash before you open the appliance door The rapid flashing of the ON OFF DOOR LOCK Led together with the flashing of at least one other LED indicates there is an abnormality see page 15 Starting and Programmes Briefly starting a programme 6 Add the detergent and any fabric softener see page 12 7 Start he programme by pressing the START RESET button To cancel it keep the START RESET button pressed for at least 2 seconds 1 Switch the Washer dryer on by pressing button 1 All the LEDS will light up for a few seconds and the ON OFF DOOR LOCK Led will begin to flash 10 2 Load your laundry into the washer dryer and 8 shut the appliance door 3 Set tte PROGRAMME knob to the programme required 4 Set the wash temperature
Download Pdf Manuals
Related Search