iHome iH36 Clock Radio User Manual
Contents
1. Batteries information e Do not mix old and new batteries e Do not mix alkaline standard carbon zinc or rechargeable batteries Install Replace the Remote Control Batteries The remote control batteries are already installed at the factory When the remote control stops operating or its range seems reduced it is time to replace them 1 Open the battery compartment cover located on the bottom of the remote control unit 2 Insert 2 AAA batteries Make sure the and ends of the batteries match the drawing inside the battery compartment We recommend the use of alkaline batteries for longer life Different types of batteries or new and used batteries are not to be mixed 3 Close the compartment cover To check for iPod compatibility iH36 is an advanced system and supports most updated iPod features To make sure your iPod works properly with iH36 please update your iPod firmware with the latest version Please check Apple s website for the same 11 Install Remote Control Battery Controls and Indicators Manual Dock Release Tab Power On LED 9 Select Up FF Button D iPod Play Pause Button Dock Open Close Button Preset Button Select Down Rew Button Radio Mode Button D Volume Button D Mute Button Volume Button Power On Off Button Play Pause Button Select Up FF Button Select Down Rew Button eo Timer Button Radio Mode Button Q2. Press the Volume and Volume Button on the main unit or the remote control to adjust the system volume Press the Mute Button to mute the output press the button again to release it restore volume Press Q Select Up FF or Select Down Rew Button on the main unit or the remote control to go to the previous or next track Press and hold while track is playing for high speed forward or reverse music search of the current track To turn off the unit press the Power On Off Button on the main unit or the remote control Your iPod will continue charging while in the dock Note Removing the iPod from the unit will not turn the iH36 off Press the Power On Off Button to turn off the iH36 Listening to iPod Shuffle Note The iH36 will not control the iPod Shuffle You must switch the iPod Shuffle on or off and play or pause it manually 1 2 3 4 5 Switch on your iPod Shuffle and play it Then dock it into the connector located on the bottom on the unit Press the iPod Play Pause Button on the main unit or the 9 Play Pause Button on the remote control to play it The iPod Icon will appear on the display Press the Volume and Volume Button on main unit or remote control to adjust the system volume Press D Mute Button to mute the output press the button again to release it Noted You may need to adjust volume control on the iPod Shuffle to made it sound right Press lt lt or gt gt Butto
3. TM Model iH36 under cabinet kitchen system for your iPod jr ESTAS gt G CR Ui GUIs OWS 9 Te EUERY WARNING The iH36 shuffle port is ONLY for use with an iPod shuffle DO NOT connect any other device such as iPod or iPhone to this port as doing so can cause damage to the iH36 iPod iPhone or both IMPORTANT Read before proceeding If you have any questions regarding the operation or use of this product please visit www ihomeaudio com faq to view answers to frequently asked questions To learn more about this and other Home products please visit us online at www ihomeaudio com 1 Table of Contents Caution Information EE 3 A Consumer Guide to Product Safety ccoo a ia 4 6 Safety Instructions FCC Information H36 Mounting Installation InStrUCTION ooo el Puer e edo dd Lans a 7 9 Getting Started m E 10 11 Install AC Power Install iPod Insert Install Replace Backup Battery Batteries information Install Replace the Remote Control Battery To check for iPod compatibility Controls andi Indicators wA 12 MAINTENANCE A ease ia 13 Setting Ups radio ie 13 Setting Time and Calendar Charging YOUFIPOO T a is 13 Listening to IPod oer n ere a Gein ames 14 Listening to IPod Shuffle rre nei EE E kou ttu tient cou rupi ter ed eee 14 Listening to FM Radio TV and Weather Band 5 erepti id t 15 Presetting Your Favorite Station eter ted erre tarta etn B n Fever repu een
4. off the unit press the Power On Off Button on the main unit or the remote control The TV tuner allows you to listen to basic broadcast channels 2 13 With TV mode selected tune in stations as in step 3 above The unit can also receive the NOAA weather channel for your area There are 7 channels in all but typically only the closest will come in With Weather mode selected follow step 3 above to find the weather channel for your area Presetting Your Favorite Station You can preset 16 stations 8 for FM 4 stations in FM1 4 stations in FM2 and 4 stations in both TV and Weather channels Presetting a Station 1 Follow step 1 to 4 in Listening to Radio above to tune in the station you wish to preset 2 Hold P E the Q Preset Button you wish to preset for about 2 seconds You will hear beep tone to confirm the station is stored 3 To preset another station repeat these steps To change a preset station tune into the desired new station and hold down the Q Preset Button The new station will replace the previously preset station and the preset number will appear Tuning into a Preset Station Press Q9 Radio Mode Button on the main unit or the remote control to turn on the radio Press Radio Mode Button to select the band ud E desired Preset Button The corresponding station channel and preset info will show on the lower part of the display Press the Volume and Volume Button on the main unit or the remote contro
5. you start each hole before drilling by first marking the center point of the guide hole then pressing an awl or nail into the mark Always wear safety goggles when operating a drill For ease and accuracy of drilling it s a good idea to drill pilot holes next using a 1 16 bit Finally use a sharp 1 4 drill bit to carefully drill 4 holes through the cabinet Make sure all holes are drilled straight and not at an angle Remove any debris c Remove the template DRILLING TIPS You may first wish to place masking tape over the opposite side you are drilling to avoid splintering Hold drill firmly to avoid the bit walking 2 Insert Spacers a Place the needed spacers into the mounting posts on top of the unit 3 Mount unit to cabinet a From inside the cabinet place a finishing washer above each hole and screw the 4 screws through any spacers into the mounting holes on the unit Make sure the unit is supported until the screws are tightened NOTE For secure mounting the screws must go into the iH36 at least 3 8 OPTION You may prefer to countersink the drilled holes from inside the cabinet if you have the correct countersink attachment for your drill This will make the screw heads flush with the cabinet surface b Tighten the screws using a Phillips head screwdriver CAUTION DO NOT USE POWER TOOLS TO TIGHTEN SCREWS Once the unit its securely mounted plug into a nearby 120Volt outlet Note that there is a built in cord
6. 4 For iPod Shuffle just plug it into the shuffle connector located on the bottom of the unit The iPod Shuffle will keep Press the Dock Open Close Button again to close the dock The iPod will recharge whether the dock is open or not charging until fully charged 13 Listening to Your iPod Note iPod Shuffle operation differs from that of other iPods See the Shuffle section below for more on using your Shuffle 1 N O OF Dock the already playing iPod The iH36 will automatically tum on and you will hear the music playing from your iPod Note If the playing song music loudness on the iPod itself is too low the iH36 may not detect that the iPod is in play mode Press the iPod Play Pause Button on the main unit or 9 Play Pause Button on the remote control twice to play it When the iPod is docked and in standby mode press the iPod Play Pause Button on the main unit or 9 Play Pause Button on the remote control to play it The iPod Icon will appear on the display If the dock is closed and you are not using 3rd generation iPod or iPod shuffle playing song info will show on the display Note When dock is closed you can only play songs on current playlist Note When using a 5G iPod iPod with video make sure to exit video playback mode before closing the dock Note DO NOT close the dock while watching a video on the 5G iPod Press the iPod Play Pause Button again to pause play press again to resume it
7. Volume Button DST Switch B Volume Button D Mute Button D Preset Button Clock Adj Button B Time Zone Button 12 Maintenance Place the unit away from sources of direct sunlight or excessive heat Clean your unit with a soft cloth moistened only with mild soap and water Stronger cleaning agents such as Benzine thinner or similar materials can mar the surface of the case Setting Up This unit has a Clock which is preset at the factory It takes just a few steps to match the clock setting to where you live T 2 3 4 Depending on your location and whether or not Daylight Saving Time DST is in effect set the 9 DST Switch located on the bottom of the unit to 1 or 1 to adjust the time forward or backward one hour Press and hold the 9 Time Zone Button located on the bottom of the unit for approx 2 seconds until the Time Zone Indicator at the lower part of the display shows the current time zone and flashes Press the Select Up FF or Q Select Down Rew Buttons to select the time zone Press the 9 Time Zone Button again to or if no key pressed for approx 10 seconds exit the setting mode If the time showing is not correct please see Setting Time and Calendar to set the clock Note You can adjust the contrast of the display by pressing and holding the 9 Time Zone Button until the zone display flashes and then pressing the Preset 1 or Preset 2 button to achieve the preferre
8. as a music CD Remote Control didn t work Dock is stuck won t open Batteries are too weak Replace with new batteries Remote Control is not pointed toward the IR sensor Power failure other Point the Remote Control toward the IR sensor below the power On Off button and try getting closer to within 10 feet of the unit Pull Manual Dock Release Tab located center top of unit Shuffle is docked yet no iPod appears on the display Shuffle is not playing Press play on your Shuffle then the iPod button on the iH36 5G iPod iPod with video temporarily locks up when docked and docking drawer is closed AND next item to play is a video file Poor initial interaction between 5G iPod and iH36 trying to load music track of video file Either let the 5G iPod remain idle for up to 90 seconds until the iPod unlocks or reset the iPod by pressing and holding the MENU and center SELECT button for 6 10 seconds until the Apple logo appears 17 Solucionando problemas La unidad no La unidad se encuentra desconectado del Conecte la unidad al tomacorrientes funciona no circula tormacorrientes corriente el ctrica f E El tomacorriente no funciona Coloque otro aparato en ese mismo tormacorriente para confirmar si el que no funciona es el tomacorriente El iPod no encastra No ha colocado el encastre del iPod o est Verifique que el encastre sea el apropiado para su iPod correctamente
9. cers Masking Tape 4 3 Phillips head screws bolts Scissors 4 41 2 Phillps head screws bolts Nail or Awl Mounting Template A for mounting template from inside cabinet Phillips head Screwdriver Mounting Template B for mounting template from below cabinet Tape Measure or Ruler BEFORE MOUNTING Safety Goggles Select a convenient kitchen cabinet with adequate clearance near a working 120 volt electrical outlet Make sure the power cord reaches the outlet easily with some extra Empty the cabinet completely before attempting to install the iH36 and thoroughly clean remove any grease etc from the cabinet Caution To reduce the risk of fire do not place or mount any heating or cooking appliance near this unit Make sure it is far enough away from heat producing products such as halogen lamps etc Front of cabinet Bottom Shelf Side view of unit H36 Mounting Installation Instructions Step 1 Measure the overhang height Use a ruler or tape measure to determine the exact amount of overhang if any Measure from the front inside bottom edge of the cabinet bottom straight down to the end of the overhang see figure 1 to determine the height of the overhang Front of Cabinet Bottom Shelf OVERHANG Measure this distance to select screw and spacer combination see chart Step 2 Determine which spacers and screws to use Once you have your overhang measurement look at Table 1 a
10. d contrast Setting Time and Calendar I 3 4 Press and hold the Clock Adj Button located on the bottom of the unit for 2 seconds until the year is flashing in the display Press the button again to accept the current setting or press the Select Up or Select Down Button until the current year is displayed Press the Clock Adj Button to confirm year setting after adjustment The display will change to show the date flashing Press the Clock Adj Button to accept the current setting or press the Select Up or Select Down Button until the current date is displayed Holding the button for a few seconds will advance or reverse rapidly Press the Clock Adj Button to confirm date setting after adjustment The time on the upper part of display will flash Press the Select Up or Select Down Button until the current time is displayed Holding the button for a few seconds will advance or reverse rapidly Remember to set the correct AM or PM Press the Clock Adj Button again to or if no key pressed for approx 10 seconds exit the setting mode Charging your iPod Note Please make sure you are using the correct insert for your iPod see Install iPod Insert on page 10 and that it is properly docked into the iH36 Failure to do so may damage your iPod I Press the 6 Dock Open Close Button to open the iPod dock then dock your iPod into it 2 While your iPod is docked in the system it recharges until fully charged 3
11. d from the dock and check for obstruction on the connectors in the dock and on your iPod Then reseat it in the dock Batteries are weak Replace with new batteries Battery Low icon always on Batteries were not installed Check to make sure the and ends match the diagram properly iPod does not iPodis not installed properly Remove your iPod from the dock and check for obstruction on respond to the the connectors in the dock and on your iPod Then reseat it in unit the dock Your iPod software is too old Upgrade software on your iPod For details visit http www apple con ipod download iPod is locked up Please make sure your iPod is working properly before docking into the unit Please refer to your iPod manual for detail 16 Trouble Shooting Sound source is distorted Symptom Possible Problem Solution Pod didn t iPod is not installed properly Remove your iPod from the dock and check for obstruction on charge up the connectors in the dock and on your iPod Then reseat it in the dock iPod is locked up Please make sure your iPod is working properly before dock P into the unit Please refer to your iPod manual for detail Problem with iPod battery batteryroblem Sound is Volume level is set too high Decrease the unit and or iPod Shuffle volume distorted If the original sound source on your iPod is poor quality distortion and noise are easily noticed with high powered speakers Try a different audio source such
12. e unit prepaid and insured to the Factory Service Center listed below Consumer Repair Department SDI Technologies Inc 1330 Goodyear Dr El Paso TX 79936 6420 Disclaimer of Warranty NOTE This warranty is valid only if the product is used for the purpose for which it was designed It does not cover i products which have been damaged by negligence or willful actions misuse or accident or which have been modified or repaired by unauthorized persons ii cracked or broken cabinets or units damaged by excessive heat iii damage to digital media players CD s or tape cassettes if applicable iv the cost of shipping this product to the Factory Service Center and its return to the owner This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original purchaser In no event will SDI Technologies or any of its affiliates contractors resellers their officers directors shareholders members or agents be liable to you or any third party for any consequential or incidental damages any lost profits actual exemplary or punitive damages Some states do not allow limitations on implied warranties or exclusion of consequential damages so these restrictions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Your acknowledgement and agreement to fully and completely abide by the above mentioned discla
13. een a e e b ER Geta 15 Presetting a Station Tuning into a Preset Station Operating the Cooking TimMer turis A eed bene ke 16 Trouble Shooting civic ahaa heated lv att nto de i ieee ah Neal eset Ga ma ates 16 19 Warranty INtorMatiON caia a oct 20 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance The symbols above are located on the top of the cabinet CAUTION To prevent electric shock match wide blade of plug to wide slot Fully insert CAUTION To reduce the risk of fire do not place any heating or cooking product beneath this unit 3 A Consumer Guide to Product Safety IMPORTANT SAFETY INSTRUCTIONS When used in the directed manner this unit has been designed and manufactured to ensure
14. ent NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy ana if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is needed Consult the dealer or an experienced radio TV technician for help SDI TECHNOLOGIES INC 1299 Main Street Rahway NJ 07065 Tel No 732 574 9000 Questions Visit www ihomeaudio com For operating instructions 1 877 ihome01 1 877 446 6301 Toll Free For any other questions 1 800 288 2792 Toll Free 6 H36 Mounting Installation Instructions Parts Supplied Tools Required 4 Small 1 2 Spacers Drill and 1 4 Drill Bit 8 Large 1 Spa
15. iPod dentro del encastre Por favor aseg rese de que su iPod funcione correctamente antes de colocarlo en el encastre Refi rase al manual de su iPod para mayor informaci n El iPod est trabado no responde La bater a del iPod usse A tener alg n ee A El volumen se encuentra muy alto Baje el volumen El sonido sale distorsionado de la unidad Si el sonido original de su iPod era de pobre calidad las distorsiones y ruidos se har n m s notables con los parlantes de alta potencia Pruebe utilizar otra fuente de audio como un CD Las bater as est n gastadas Reemplace las bater as por nuevas Apunte el control remoto hacia el iH36 y mant ngase a una distancia m xima de 10 pies de la unidad El compartimiento No hay corriente el ctrica u otras causas Tire de la leng eta de destrabe en la parte superior de la est trabado no abre unidad No est apuntando el control remoto hacia el iH36 El Shuffle no funciona Oprima play en el Shuffle luego el bot n iPod en el iH36 La interacci n inicial entre el iPod 5G y el iH36 es pobre cuando la m sica es de un archive de video Deje el iPod 5G sin usar por 90 segundos hasta que se desbloquee o reajustelo oprimiendo el botones MENU y el centro SELECT por 6 10 segundos hasta que el logotipo de Apple aparezca 19 Limited 90 Day Warranty Information iHome Products a division of SDI Technologies Inc hereafter referred to as SDI Technologies warrants this prod
16. imer of warranty is contractually Pinang to you upon your transfer of currency money order cashier s check or credit card for purchase of your SDI Technologies product M Questions Visit www ihomeaudio com For operating instructions 1 877 ihome01 1 877 446 6301 Toll Free For any other questions 1 800 288 2792 Toll Free 1H36 020606 B Printed in China
17. k and put the insert into it gently Please note that iPod must not be in a case or skin Note If for any reason the iPod dock does not open power failure etc simply pull on the Manual Dock Release Tab located near the front at the top center of the unit 10 Getting Started Install Replace Backup Batteries If Backup Batteries are installed and a power failure occurs or the AC cord is accidentally disconnected the current time and radio preset station settings will be temporarily maintained Otherwise you must reset the time and radio preset station settings mies backs batteries are installed in the unit before shipping to keep the clock running If the unit has no display or the Battery Low Icon located on the right of the display is on replace backup batteries 1 Please make sure the AC cord is connected otherwise all settings may be lost during battery replacement 2 Open the battery compartment cover located on the bottom of the unit 3 Insert 3 AA batteries Make sure the and ends of the batteries match the drawing inside the battery compartment We recommend the use of alkaline batteries for longer life Different types of batteries or new and used batteries are not to be mixed 4 Close the compartment cover NOTE When operating on battery backup certain functions time zone clock adjust DST switch are disabled Though the colon in the time display does not flash the clock will work properly
18. l to adjust the system volume To turn off the unit press the Power On Off Button 15 the main unit or the remote control oa AO os On Operating the Cooking Timer The cooking timer can be set at one minute intervals between 1 120 minutes 1 Press the Timer Button once to activate the cooking timer 2 You will see 60 on the display meaning the cooking timer will sound after 60 minutes To adjust the timer press and hold the Timer Button until the display flashes Then press the Select Up FF or Select Down Rew Button until the time you want is displayed 3 Ina few seconds the display will change back to show the real time and the Timer Icon will show on the left side of the display to indicate the cooking timer is on 4 Press the Timer Button once to view the time remaining or press twice to tum off cancel the timer 5 When the time is up a buzzer will sound It will continue for 1 minute Press any button to stop it immediately Trouble Shooting Symptom Possible Problem Solution Unit doesn t AC cord isn t plugged into a Plug the AC cord into a wall respond wall outlet outlet no power Wall outlet is not functioning Plug another device into the same outlet to confirm the outlet is working properly iPod does not Not using an iPod insert or Make sure the dock insert is the proper fit for your iPod see dock properly using the wrong one chart on page 10 iPod not installed properly Remove your iPo
19. n on your iPod shuffle to go to the previous or next track Press and hold while track is playing for high speed forward or reverse music search of the current track To tum off the unit press the Power On Off Button on the main unit or the remote control Please remember to tum off iPod Shuffle too Note Any time you wish to listen to your Shuffle press play on your Shuffle then press the iPod Button 14 Listening to FM Radio TV and Weather Note Extend FM wire antenna fully for best reception 1 Press the Radio Mode Button on the main unit or the remote control to play the radio The radio frequency channel will appear on the lower part of the display 2 Press the Radio Mode Button to select the desired band Each press changes the band as follows Z FM1 FM2 TV Weather El By using FM1 or FM2 preset mode you may listen to FM band radio on either mode see Presetting Your Favorite Station below Use Select Up FF or Select Down Rew Button to tune in to the desired station While under FM1 or FM2 mode press and hold the Select Up or Select Down Button for appox 2 seconds to auto seek available stations Seek will stop at the first clear stereo signal To seek a different station continue as described Press the Volume and Volume Button on the main unit or the remote control to adjust the system volume Pres Mute Button to mute the output press the button again to release it 6 To turn
20. nd find the nearest measurement in the Overhang column then determine the combination of spacers and screw size you need Set them apart Examples If your cabinet has no overhang just use 4 of the 3 inch screws with no spacers If your cabinet has a 1 inch overhang use 4 of the 1 2 spacers 4 of the 1 spacers and four 4 1 2 screws Table 1 SPACER SCREW SELECTION CHART OVERHANG SPACERS SCREW 0 3 8 1 2 3 4 3 x4 7 8 13 g 1 2 spacerx4 41 x4 1 spacer x 4 11 2 13 4 41 2 x4 17 8 21 4 12 Spacerx4 44x4 1 spacer x 8 Note This unit is designed for cabinets with an overhang of 2 1 4 or less If your cabinet has an overhang longer than 2 1 4 please call a customer service representative at 1 800 228 2792 H36 Mounting Installation Instructions MOUNTING THE H36 We recommend the unit be mounted flush to the front edge of the cabinet 1 Select and Set Template and Drill holes a Using a Template First decide which mounting method template you prefer the inside the cabinet template Mounting Template A or the under the cabinet template Mounting Template B Next cut out the selected template on the line indicated depending on whether your cabinet has an overhang or not Position the chosen Mounting Template either inside or under the cabinet with the arrow facing the front of the cabinet Secure in place with tape b Drilling There are 4 guide holes on the mounting template We recommend that
21. nto the outlet try reversing the plug If the plug still fails to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug by forcing the plug into the outlet 6 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them It is always best to have a clear area from where the cord exits the unit to where it is plugged into an AC outlet 7 Cleaning The unit should be cleaned only as recommended See the Maintenance section of this manual for cleaning instructions A Consumer Guide to Product Safety 8 Objects and Liquid Entry Care should be taken so that objects do not fall and liquids are not spilled into any openings or vents located on the product 9 Attachments Do not use attachments not recommended by the product manufacturer 10 Lightning and Power Surge Protection Unplug the unit from the wall outlet and disconnect the antenna or cable system during a lightning storm or when it is left unattended and unused for long periods of time This will prevent damage to the product due to lightning and power line surges 11 Overloading Do not overload wall outlets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock 12 Damage Requiring Service The unit should be serviced by qualified service personnel when A the power s
22. uct to be free from defects in workmanship and materials under normal use and conditions for a period of 90 days from the date of original purchase Should this poda fail to function in a satisfactory manner it is best to first return it to the store where it was originally purchased Should this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period SDI Technologies will repair or at its discretion replace this product without charge except for a 10 00 charge for handling packing return UPS postage and insurance This decision is subject to verification of the defect or malfunction upon delivery of this product to the Factory Service Center listed below The product must include proof of purchase including date of purchase The fee for service without proof of purchase is 30 00 Before returning this product for service please first replace the batteries if applicable with fresh ones as exhausted or defective batteries are the most common cause of problems encountered If service is still required 1 Remove the batteries if applicable and pack the unit in a well padded heavy corrugated box 2 eno a photocopy of your sales receipt credit card statement or other proof of the date of purchase if within the warranty period 3 Enclose a check or money order payable to the order of SDI Technologies for the sum of 10 00 30 00 without proof of purchase 4 Send th
23. upply cord or plug has been damaged B objects have fallen into or liquid has been spilled into the enclosure C the unit has been exposed to rain D the unit has been dropped or the enclosure damaged E the unit exhibits a marked change in performance or does not operate normally 13 Antenna Do not connect an external antenna to the unit other than that provided 14 Periods of Nonuse If the unit is to be left unused for an extended period of time such as a month or longer the power cord should be unplugged from the unit to prevent damage or corrosion 15 Servicing The user should not attempt to service the unit beyond those methods described in the user s operating instructions Service methods not covered in the operating instructions should be referred to qualified service personnel Questions Visit www ihomeaudio com For operating instructions 1 877 ihome01 1 877 446 6301 Toll Free For any other questions 1 800 288 2792 Toll Free A Consumer Guide to Product Safety FCC Information This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Warning Changes or modifications to this unit not expressly approved by the party responsible for compli ance could void the user s authority to operate the equipm
24. utilizando el encastre incorrecto El iPod no encastra correctamente Quite el iPod del encastre y retire la posible obstrucci n del encastre o de su iPod Vuelva a colocar el iPod dentro del encastre El cono de bater a Las bater as est n gastadas Reemplace las bater as baja est destellando Las bater as no est n instaladas Verifique que la polaridad de las bater as C y se encuentren correctamente de acuerdo al diagrama del compartimiento de bater as El iPod no se El iPod no est instalado correctamente Quite el iPod del encastre y verifique posibles obstrucciones comunica con la del encastre o de su iPod Vuelva a colocar el iPod dentro unidad del encastre Su software es obsoleto Renueve su software Para mayor informaci n dir jase a http www apple con ipod download El iPod no responde Verifique que su iPod funcione correctamente antes de conectarlo a la unidad Refi rase al manual de su iPod para m s detalles 18 El iPod no carga El sonido sale distorsionado El control remoto no funciona El Shuffle est encastrado pero no IPod aparece en el visor El iPod 5G iPod con video puede bloquearse temporariamente cuando est conectado con el cajon cerrado Y la siguiente canci n a tocar es de un archive de video Solucionando problemas El iPod no est instalado correctamente Quite el iPod del encastre y retire la posible obstrucci n del encastre o de su iPod Vuelva a colocar el
25. wrap on the back of the unit to wrap up any excess wire Getting Started Thank you for purchasing the Home H36 kitchen Stereo System for your iPod Designed specifically to work with your iPod or Shuffle this system provides high quality audio and radio performance that invites your music to come out and play It also has a factory preset clock with the correct time already preset at the factory so you just need a few steps to make it work Please read the instructions carefully before operating the appliance and keep it for future reference Install AC Power Plug the AC cord into wall outlet AC power cord should connect directly to a wall outlet Wind up the AC cord to keep it from hanging down and contacting hot cooking appliances Install iPod Insert Your iH36 comes with 3 removable inserts and a rubber pad to ensure your iPod fits properly in the iPod drawer Please see below table to insert replace rubber pad to fit your iPod m er Thick iPod 5G iPod Dock into the Shuffle Use with iPod3G 10 15 20GB iPod 3G 30 40GB iPod Nano Replace rubber pad connector located in the iPod Mini iPod 4G 20 GB iPod 4G 40 GB 2 4GB per instruction on the bottom of the unit iPod Photo 20 30 GB iPod Photo 60 GB 5G rubber pad card To place an insert 1 Select the insert for your iPod see chart above Using the correct insert rubber pad ensures a proper fit for your iPod 2 Press the Dock Open Close Button to open the iPod doc
26. your personal safety However improper use can result in potential electrical shock or fire hazards Please read all safety and operating instructions carefully before installation and use and keep these instructions handy for future reference Take special note of all warnings listed in these instructions and on the unit 1 Water and Moisture The unit should not be used near water For example near a bathtub washbowl kitchen sink laundry tub swimming pool or in a wet basement 2 Ventilation The unit should be situated so that its location or position does not interfere with its proper ventilation For example it should not be situated on a bed sofa rug or similar surface that may block ventilation openings Also it should not be placed in a built in installation such as a bookcase or cabinet that may impede the flow of air through the ventilation openings 3 Heat The unit should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat 4 Power Sources The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance 5 Grounding or Polarization This product is equipped with a polarized alternating current line plug a plug having one blade wider than the other As a safety feature this plug will fit into the power outlet only one way If you are unable to fit the plug fully i
Download Pdf Manuals
Related Search