IBM 6866 Personal Computer User Manual
Contents
1. 3 WALL TOWER AND CURVED GLASS INSTALLATION STEP 13 Turn on water supply and check for leaks Correct any leaks before installing tower cover STEP 14 Install tower cover as shown Insert cover at top first TOWER TOP PLATE TOWER COVER INSERT THIS SIDE FIRST TOWER COVER 22 STEP 15 Seal all around the base of tower with silicone sealant Also seal the inside of both wall posts bottom of both glass panels on the inside only APPLY SEALANT ALONG BASE OF GLASS APPLY SEALANT APPLY SEALANT ALL AROUND ALONG BASE TOWER BASE AND SIDE OF WALL POST RAILS NOT SHOWN TOP VIEW 2 amp 3 WALL OPERATION Shower Head There are four selectable positions Jet normal pulsating and aerated flow Body Sprays 2 Upper amp 2 Lower To adjust the flow and intensity turn as shown The spray can also be turned to change the direction of the spray LESS FLOW AND INTENSITY MORE FLOW AND INTENSITY Diverter Control To turn On water turn the inner knob clockwise and adjust for more or less flow The outer knob will divert the water to body sprays shower head shown in this position and foot temperature tester If the knob is pointing anywhere between main functions the amount of water will be proportional to where the knob is pointing If the knob is pointing to the white line between positions2. 20 STEP 7 Place the front rail and tower support rail against the walls Check level and mark the position for the rail mounting bracket The screw position will be above the rail Drill the wall with a 3 16 bit and secure bracket with screws and wall anchors provided ATTACH RAIL BRACKET TO WALL SECURE RAIL TO BRACKET TURN CW TO TIGHTEN MOVE COVER CAP OVER BRACKET STEP 8 Adjust the rails until tower is vertical in 2 planes 3 WALL TOWER AND CURVED GLASS INSTALLATION STEP 9 Secure the rails STEP 10 Tighten the tower base bolt Two shut off valves are provided To hook up supply lines unscrew valves from braided line Using thread sealant screw valve to stub outs at bottom of tower Then reconnect braided line using provided gasket Do not twist or kink supply lines when connecting SHUT OFF VALVES _ PROVIDED 21 STEP 11 Install cover cap on wall post COVER CAP n STEP 12 Install glazing gasket on curved glass wall post on the inside Note orientation of gasket Soapy water may help to insert the glazing gasket GLASS INSIDE OF ENCLOSURE WALL POST GLAZING GASKET TOWER TOP PLATE INSIDE OF GLAZING GASKET ENCLOSURE
3. SUMMER RAIN 2 WALL amp 3 WALL WALK IN SHOWER SYSTEMS INSTALLATION AND OPERATING INSTRUCTIONS IMPORTANT SAFETY INFORMATION Do not place or use electrically connected devices such as television radio or stereo speakers lights hair dryers or telephones within 1 5 m 5 feet of shower Note This is a professional grade product A knowledge of construction techniques plumbing and electrical installation according to codes are required for proper installation and user satisfaction We recommend that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath products Our warranty does not cover improper installation related problems 2 WALL Specifications CONTENTS Rough in Reference Component Identification Base Installation Tower and Glass Panels Installation 3 WALL Specifications Rough in Reference Component Identification Base Installation Tower and Glass Panels Installation 2 amp 3 WALL Operation Maintenance Tower Fixture Repair Parts Tower Plumbing Repair Parts 2 Wall Unit Repair Parts 3 Wall Unit Repair Parts Warranty Save These Instructions for Future Use Date Purchased Owner s Record Purchased From Installed By Serial Number Model 5 7 8 12 13 14 15 16 18 19 22 23 24 25 26 27 28 29 30 2 WALL SPECIFICATIONS Important Read
4. H FRONT VIEW 2 WALL ROUGH IN REFERENCE zl 7 84 y FRONT VIEW p 60 gt 33 3 4 ___ le 23 1 1 2 TILE FLANGE 21 1 2 5 r 1 2 RIGID COPPER PIPE UNDER BASE 27 15 16 42 5 16 COLD SUPPLY HOT SUPPLY MINIMUM WATER PRESSURE FOR THE SYSTEM IS 40PSI TOP VIEW 2 WALL COMPONENT IDENTIFICATION TOWER WITH PLUMBING FIXTURES MAGNETIC HEX WRENCH 1 GASKET BOTTOM PLATE CURVED STRAIGHT PROVIDED AND TOP COVER GLASS GLASS PREASSEMBLED MOUNTING WALL mine POST MOUNTING WALL MOUNTING CAP 2 TOWER POST POST MOUNT SUPPORT BRACKET 2 S RAIL GLASS lt gt E SUPPO FRONT UPPORT EN BRACKET s BAIL o RAIL EN COVER 2 GLAZING 7 m Ld TAPE NS 6 PIECES P dri 111 3 SCREWS AND 3 WALL ANCHORS PER MOUNTING GLAZING GASKET 3 n STRAIGHT GLASS E PANEL GLAZING GASKET l TOWER BOTTOM COVER TOWER MOUNTING BRACKET BOLT amp WASHER CORNER POST 0 SELF DRILLING SCREW 2 WALL BASE INSTALLATION PRELIMINARY ROUGH IN The floor structure beneath the unit must be able to support a total weight of the unit and bather Refer to the table under total weight STEP 1 Provide an o
5. the water will be diverted equally to both functions on either side of the white line STOP RELEASE SHOWER HEAD O ERATURE STER Temperature Valve The temperature of the mixed water is adjusted by means of the graduated handle This handle has a safety stop set at 100 F 38 To increase the temperature press the red button to release the stop and keep turning the handle Foot Temperature Testor 23 2 amp 3 WALL MAINTENANCE To remove any lime scale from the shower head and body sprays rub with your finger the outer ring of nozzles on the shower head and all nozzles on the body spray To clean the foot temperature tester unscrew the nozzle and back flush the wire mesh filter Do not use metal tools such as scissors or screwdrivers etc to clean the body sprays shower head or foot temperature tester To cleanthe base simply use a mild nonabrasive liquid detergent solution You can protect and restore the gloss to a dulled acrylic surface by applying Meguiar s 10 Mirror Glaze a product specifically designed for use on acrylic finishes If Meguiar s is not available an acrylic polish of equal quality or automotive paste wax is acceptable The glass can be cleaned with any glass cleaning product available on the market Do not use abrasives alcohol acetone ammonia or other solvents on any tower component The thermostatic valve has 2 screen filters that should be cleaned periodically To remove the filter
6. Deeg 352 6 029 2 gt 03 5 o wo e 0 O DZO 23 o 32g 02 0 5 sc 6 00 5555 0 900522 8a o lt lt S 239 45 522 53 9 z89 2 235 So072725937898 D 3 60 4 9 tototo Dozg 3 o 100 5 zggso 905 2 0 9 lt 0 3 d do 3 306 2 So 995 5 oc 2 2 zS EES 5 283z 2 ERTELE 2835893 B zs d S30 gt o 5 3 2 2520 5 5 9 ox 22 S Baal 350907 c va lI 5 9 5 20982 525 5 5235 00 gt 25 D oy 3 S 6G ya xe ore c lt 5 2 Z S 25737043 E 2 a 05 zaz223 c 3 y2z9coo 2 ONS 2222 098 2525 D Of ET aj i 5 2898 gz 33 9988 Be Oks 82850 BY 558 23 82550 98 BES 98 88 o r Fd oo 5 E o X RP S588 ss 80535 S EP 5 68 S Bg 8825 38 845 532l 5 25398 8 2Zg 5 B vv E A a zoo oo 54 mk lt E w zy 3 a g Bone Bs 4935 gt gt 05 Su si 2 S 8228 Z QA 2 88 lt lt 900 oz a 9 og Cees 59 Q gt SES6 lt 88 ag o 8 5025 99 2 o S a9 c E xu
7. 1 9 ID X 063 Thick G432000 Nipple 1 2 Close 10 U217827 Shower Head Chrome 11 U215827 Jet Wall Body Chrome 12 U219827 Face Plate Transfer Valve Chrome 13 U546827 Nut Transfer Valve Chrome 14 U545827 Oollar Transfer Valve Chrome 15 U544000 O Ring Transfer Valve 16 U543827 Knob Flow Control Chrome 17 U549827 Collar Mixer Valve Chrome 18 U548827 Knob Mixer Valve Chrome 19 D709827 Fill Spout Assembly Stubby Chrome 25 TOWER PLUMBING REPAIR PARTS A944000 9X Spring Clamp 625 OD Hose U405000 L 5 5 Tubing PVC Reinforced 10mm Barb A945000 7X Spring Clip 75 OD Hose U400000 FTG Straight 1 2 FTS X 10mm Barb U403000 2X Cap 1 2 FST U711000 2X Strainer Washer 1 2 Dia 10 GASKET 2X Gaskets Supplied with Hose 11 U827000 2X Ball Valve 5 FTP X 5 MPT L 12 U421000 11X Washer FTG 7 OD 13 U401000 7X FTG Ell 1 2 FST X 10mm Barb 14 0405000 1 4 5 Tubing PVC Reinforced 10mm Barb 15 U404000 2X FTG Y 10mm X 10mm X 10mm Barb 16 0405000 L 2 5 Tubing PVC Reinforced 10mm Barb 17 U402000 FTG Tee 1 2 FST X 10mm Barb 18 U405000 L 10 0 Tubing PVC Reinforced 10mm Barb 19 0405000 1 4 5 Tubing PVC Reinforced 10mm Barb 20 U405000 L 5 5 Tubing PVC Reinforced 10mm Barb Note 1 For Clamping U405000 to U401000 or U402000 Note 2 For Clmping U405000 to U400000 or U404000 U405000 L 31 0 Tubing PVC R
8. MOUNT SUPPORT BRACKET 2 BAIL gt o BRACKET COVER 2 OMS NC _ TAPE N f 3 PLACES 3 SCREWS AND GLAZING 3 WALL ANCHORS GASKET CURVED GLASS TOWER COVER GLAZING GASKET 2 TOWER MOUNTING BOLT amp WASHER SELF DRILLING SCREW BASE 3 WALL BASE INSTALLATION PRELIMINARY ROUGH IN The floor structure beneath the unit must be able to support a total weight of the unit and bather Refer to the table under total weight STEP 1 Provide an opening in the subfloor no less than 5 x 5 square This opening should be located on the center lines ofthe shower base drain hole See Product Chart The opening is to accommodate a 2 waste pipe The waste pipe should be 1 4 to 1 2 above the surface of the subfloor 90 90 so 2 WASTE PIPE 5 x5 OPENING MIN AS POSSIBLE Loo As shown in top view 1 2 copper pipes are provided to connectto the water supply Also provided are 2 loose 45 elbows as shown for installation in Detail 1 CAUTION A nonflammable protective barrier must be placed between soldering work and base unit to prevent damage to the base When connecting the supply lines the toe plate can be notched to accommodate the pipes The pipe underthe base can be cutto
9. OARD TILE ADHESIVE STEP 8 Filling the area marked DO NOT FILL will prevent moisture from draining back into the base through the weep holes This moisture is due to leakage through the tile grout Sealing the tile grout will preventthis leakage T CEMENT __ dicis GROUT RERFRFERSFERFRFRE MOM RN NN RT RT s SILICONE SEALANT SHIM IF NECESSARY DO NOT FILL 1 1 8 MAXIMUM NO MINIMUM STUD SILICONE GAP 2 d SEALANT SILICONE SEALANT 1 4 MINIMUM GAP CLEAN UP AFTER INSTALLATION To avoid dulling and scratching the acrylic surface of the base never use abrasive cleaners A mild liquid detergent and warm water clean soiled surfaces Remove spilled plaster with a wood or plastic edge Metal tools scratch the surface Spots left by plaster or grout can be removed if lightly rubbed with detergent on a damp cloth or sponge Paint tar or other difficult stains can be removed with paint thinner turpentine or isopropyl alcohol rubbing alcohol Minor scratches which do not penetrate the color finish can be removed by lightly sanding with 600 grit wet dry sandpaper You can restore the glossy finish to the acrylic surface of the base with a special compound 10 Mirror Glaze If not available use auto motive rubbing compound followed by an application of automotive paste wax Ma
10. RANTY CARD The attached Warranty Registration Card MUST be filled out by the purchaser within thirty 30 days from purchase and mailed to Jacuzzi Whirlpool Bath in order for this warranty to become effective Jacuzzi Whirlpool Bath P O Drawer J Walnut Creek CA 94596 9885 Luz 5 N gt ao SOS 329 lt 3 lt A 4 PN m gt bi PRPRPERL 2 PEs ex ct 19 0 40D 25 x 2 8 i 2272 Bs 222286 5 826 Os EB mg 2 D PJ S ec 9 o 22 2D o o D 2 2 o 55 Z lt lt 3 2000 0010 OVO lt 0 lt gt o 3 650205 3 3 2 2 3 z S820 2322NO55 390 lt S 3 5 52 3 5 05 55 5 52295253525 6222 2295 508 0 52 850 2 g983E 3 2 0 5 O03207 lt 09365 g gt 2059 55899999eo o2252522 085523 9 750 880489 D amp 83 D 9 CO 3w 32 0965 0 22 505 7 muo2 a 232 20 zT 322282552 lt o CGP 2 BQO lt lt 56000 so Sogz 9 o3 3 p
11. XXX for 801 Satin 827 Chrome 938 Timber 959 White 27 7 a 3 90 12 14 6X b 19 Used with Tower with Timber Finish Only 21 For colors for U174XXX Shower Base substitute XXX for Standard 959 White 958 Almond 969 Oyster 945 Silver High Fashion 917 Black 949 Rose 951 Shell 978 Forest Green 984 Shy Blue 999 Sand 3 WALL UNIT REPAIR PARTS 1 3 2X 4 Pact 2 jM V 10 11 7 80 _ U134827 Rail Back Walk in 3 Wall 6N KS 9 1 2 1245827 Rail Assembly Walk in Wall f 3 U149000 Bracket Mounting Rail 4 U119827 Wall Post Panel 5 0138827 Cap Wall Post 6 U124XXX Tower Cover 7 U257XXX Final Shell Tower Walk in 3 Wall 12 13 U126XXX Tower Body Walk in U136XXX Cap Top Tower EY U137XXX Cap Bottom Tower U149000 Bracket Mounting Rail U354000 Screw Self Tap 8 1 25 L U355000 Screw Self Tap 8 2 0 L 8 U247000 Gasket Vinyl Glass Panel 9 U113000 Glass Panel Front Walk in 10 0159000 Gasket Vinyl Glass Panel 11 J686000 Tape High Bond 2 Sided 12 U354000 Screw Self Tap 8 1 25 L 13 0703000 Anchor 6 8 10 l 14 3952832 Bolt Full Thread 5 16 15 3983832 Washer 5 16 Flat Type 2 Plnwser 16 U171XXX Shower base Walk in 3 Wall 17 0220000 Screw Self Drilling 8 X 1 63 L 18 9959000 Drain Non Caulk For finishes for U124XXX Tower Cover and U257XXX Tower Final Shell substitute XXX for 801 Sa
12. complete instructions before beginning installation Each unit arrives ready for installation equipped with base glass and associated hardware Remove the unit from the carton Retain the shipping carton until satisfactory inspection of the product has been made Immediately upon receipt inspect the base and other components before installing Check all carton inserts for parts and hardware Should inspection reveal any damage or defect in any component do not install the unit Damage or defect to any component claimed after the unit is installed is excluded from the warranty Jacuzzi Whirlpool Bath s responsibility for shipping damage ceases upon delivery of the products in good order to the carrier Refer any claims for damage to the carrier For definitions of warranty coverage and limitations refer to the published warranty information packed with the product Jacuzzi Whirlpool Bath is not responsible for any defect that could have been discovered repaired or avoided by following this inspection BASE SPECIFICATIONS L 45 ELBOW DIMENSIONS 2 PP DOSE 1 1 2 TILE FLANGE 60 1219 mm L 42 5 16 1075 mm W m 4 102 mm H 1 2 RIGID PRODUCT WEIGHT Base Enclosure COPPER PPE TEAD UNDER BASE 89 kg TOTAL WEIGHT FLOOR LOADING 396 Ib 180 kg 23 10 4 ft i 112 kg sq m TOP VIEW NOTE MINIMUM WATER PRESSURE FOR THE SYSTEM IS 40 PSI 1 1 2 Y
13. einforced 10mm Barb U405000 L 31 0 Tubing PVC Reinforced 10mm Barb U540000 2X 1 2 Flexhose 38 Female Swivel Heads 26 1 See Note 1 2 4 See Note 2 5 7 8 9 9X 7 7X __ 4 ee 24 d 2 12 11X 13 7X 18 19 20 SS DO IO Um oN gt 2 WALL UNIT REPAIR PARTS 10 U134827 Rail Back Walk in U133827 Rail 2 Wall Walk in U245827 Rail Assembly Walk in U149000 Bracket Mounting Rail U119827 Wall Post Panel U138827 Cap Wall Post J686000 Tape High Bond 2 Sided U159000 Gasket Vinyl Glass Panel U479XXX Glass Panel Assembly Walk in 0 U124XXX Tower Cover 1 U257XXX Final Shell Tower Walk in U126XXX Tower Body Walk in U136XXX Cap Top Tower U137XXX Cap Bottom Tower U149000 Bracket Mounting Rail U354000 Screw Self Tap 8 1 25 L U355000 Screw Self Tap 8 2 0 L 2 U113000 Glass Panel Front Wlak in 3 U354000 Screw Self Tap 8 X 1 25 L 4 U703000 Anchor 6 8 10 5 5374832 Screw Sheet Metal PHP 6 X 88 L 6 U196000 Bracket Corner Post Bottom 7 3952832 Bolt Hex FL Thrd 5 16 8 3983832 Washer 5 16 Flat Type A PInwdser 9 0247000 Gasket Vinyl Glass Panel 0 U174XXX Shower base Walk in 2 Wall 1 0220000 Screw Self Drilling 8 X 1 63 L 2 9959000 Drain Non Caulk For finishes for U124XXX Tower Cover and U257XXX Tower Final Shell substitute
14. en the tower base bolt Two shut off valves are provided To hook up supply lines unscrew valves from braided line Using thread sealant screw valve to stub outs at bottom of tower Then reconnect braided line using provided gasket Do not twist or kink supply lines when connecting SHUT OFF 2 VALVES PROVIDED 2 WALL TOWER FIXED WALL AND CURVED GLASS INSTALLATION STEP 13A STEP 14 Insert fixed glass support rail into panel post and tighten Install cover cap on fixed glass wall post set screw COVER CAP T d lt A lt lt lt STEP 13B Drill a 1 8 pilot hole into tower support rail using the hole STEP 15 in the glass panel support rail Screw M3 5X9 5 mm Install glazing gasket on fixed glass wall post and curved screw into hole glass wall post on the inside Note orientation of gasket Soapy water may help to insert the glazing gasket DRILL 1 8 PILOT HOLE AND SCREW 5 9 5 mm SCREW INTO HOLE GLASS GLASS PANEL SUPPORT RAIL INSIDE OF ENCLOSURE WALL POST GLAZING GASKET TOWER TOP PLATE INSIDE OF GLAZING GASKET ENCLOSURE 2 WALL TOWER FIXED WALL AND CURVED GLASS INSTALLATION STEP 16 Turn on water supply and check for leaks Correct any leaks before installing
15. fer any claims for damage to the carrier For definitions of warranty coverage and limitations refer to the published warranty information packed with the product Jacuzzi Whirlpool Bath is not responsible for any defect that could have been discovered repaired or avoided by following this inspection L gt BASE SPECIFICATIONS 45 ELBOW 2 PROVIDED 1 1 2 TILE FLANGE DIMENSIONS LOOSE 60 1219 mm L 42 5 16 1075 mm W 4 102 mm H f ES 1 2 RIGID COPPER PIPE PRODUCT WEIGHT Base Enclosure UNDER BASE 140 Ib 64 kg TOTAL WEIGHT FLOOR LOADING 340 Ib 155 kg Y 23 10 ft 97 kg sq m TOP VIEW NOTE MINIMUM WATER PRESSURE 1 4 2 TILE FLANGE FOR THE SYSTEM IS 40 PSI Hi 7 1 FRONT VIEW 3 WALL ROUGH IN REFERENCE 84 y FRONT VIEW 60 k 33 3 4 gt 23 1 1 2 TILE FLANGE k 21 1 2 a HH 1 2 RIGID 27 15 16 COPPER PIPE UNDER BASE 42 5 16 gue COLD SUPPLY HOT SUPPLY MINIMUM WATER PRESSURE FOR THE SYSTEM IS 40PSI TOP VIEW 3 WALL COMPONENT IDENTIFICATION TOWER WITH PLUMBING FIXTURES MAGNETIC HEX WRENCH 1 GASKET BOTTOM PLATE CURVED PROVIDED AND TOP COVER GLASS PREASSEMBLED WALL MOUNTING MOUNTING POST WALL TOWER POST CAP
16. is of the nature or type covered by the warranty the user has informed an Authorized Jacuzzi Whirlpool Bath Service Agent or Warranty Service Department Representative of the nature of the problem during the warranty period conclusive evidence e g proof of purchase or installation is provided to the foregoing by the user proving that the failure occurred or was discovered within the warranty period an authorized independent service person or Company representative has been permitted to inspect the unit during regular business hours within a reasonable time after the problem was reported by the user In order to obtain warranty service consult your local telephone book for the location of the nearest Jacuzzi Whirlpool Bath Authorized Service Agent Describe the problem and the Authorized Service Agent will inspect the unit and provide the required warranty service If you are unable to contact a Jacuzzi Whirlpool Bath Authorized Service Agent call or write Jacuzzi Whirlpool Bath Warranty Service Department P O Drawer J Walnut Creek California 94596 Call 925 938 7411 To obtain warranty replacement for factory installed components for Company supplied options and accessories manufactured and supplied by the Company call or write the above Provide a description of the problem and proof of purchase You will be instructed how to obtain replacements and where to return at your expense the failed component s option s or accessory ies Al
17. jor scratches and gouges which penetrate the acrylic surface require refinishing Ask your Jacuzzi Whirlpool Bath dealer for special instructions 2 WALL TOWER FIXED WALL AND CURVED GLASS INSTALLATION STEP 1 Position the wall posts so the edge of the post is set back 3 4 19 mm in from the edge of the base 3 4 J 19 mm gt EDGE OF BASE FINISH WALL STEP 2 Level both wall posts in their proper position and mark where screw holes are to be drilled Drill 3 16 holes and secure with wall anchors and screws provided Cuta 12 strip of tape provided and apply firmly over screw heads 6 PLACES STEP 3A Slide straight glass panel all the way into wall post Mark position of glass post Remove panel MARK POSITION STEP 3B Apply a bead of silicone sealant on underside of bottom bracket corner post and place bracket where marked Drill pilot holes 48 screw and secure bracket to base Reinsert panel into wall post and position glass post over bracket APPLY BEAD OF SILICONE SEALANT ON UNDERSIDE OF BOTTOM BRACKET CORNER POST 2 WALL TOWER FIXED WALL AND CURVED GLASS INSTALLATION 4 Slide the glass panel into the wall post Make sure that the corner notch is positioned toward the base of the tower STEP 5 Place the tower onto base Ensu
18. l of the drain assembly STRAINER APPLY LUBRICANT SILICONE DRAIN SEALANT ASSEMBLY SHOWER BASE RUBBER WASHER FIBER WASHER STEP 3 If the subfloor is level no other preparation is neces sary You can proceed to install the shower base Ifthe subfloor is not level level shower base by spreading floor leveling compound mortar plaster or minimal expansion structural foam with a minimum density of 5 lbs cubic feet EVENLY over ENTIRE area where base will be installed The compound used MUST make contact with the entire bottom surface of the base Both sides of a joint or splice of subfloor should be level to each other Level and support waste pipe cutout area greater than 5 x 5 The base is NOT to be supported by the tile flange SPREAD MORTAR OR LEVELING COMPOUND ETC EVENLY OVER ENTIRE AREA 2 WALL BASE INSTALLATION STEP 4 With the drain fitting passing over the center of the drainpipe lower the shower base carefully into place push down firmly until the base is in place You must check the level of the base in two directions Do not lift a corner to level the base This will cause a loss of contact with the mortar Attach the shower base flange to the stud wall and blocking with self drilling screws included Use a minimum of 3 screws per flange section POSITION BASE OVER CENTER OF STEP 5 With a large screwdriver and the tool included with the drain
19. l replacement parts equipment and repairs shall assume the remaining warranty period of the part s replaced The Company s warranty obligation shall be discharged upon tender of replacement or repair The customer s refusal to accept the tender terminates the Company s warranty obligation 2002 Jacuzzi Whirlpool Bath U223000D 2 04 wa 2 D o pe s 5 0 a 1712120 o 3 pe lt
20. length To do so remove the pipe clamps under the base cutthe pipe and reinstall pipes STUD WALL NOT PROVIDED lt 45 ELBOW PROVIDED 2 DEATAIL 1 INSTALLATION INSTRUCTIONS STEP 2 Remove the stainless steel strainer from the drain assembly Disassemble the locknut and two gaskets from the back of the drain assembly Apply a 1 4 bead ofcaulking silicone to the drain hole and insertthe drain assembly Replace the rubber washer fiber washer and lock nut in that order Hand tighten the locknut Remove excess sealant from finished side Apply a lubricant common household liquid soap works well to the inside of the rubber seal of the drain assembly BEBE S STRAINER SILICONE SEALANT APPLY LUBRICANT DRAIN ASSEMBLY SHOWER BASE i E gt RUBBER WASHER FIBER WASHER STEP 3 If the subfloor is level no other preparation is neces sary You can proceed to install the shower base Ifthe subfloor is not level level shower base by spreading floor leveling compound mortar plaster or minimal expansion structural foam with a minimum density of 5 lbs cubic feet EVENLY over ENTIRE area where base will be installed The compound used MUST make contact with the entire bottom surface of the base Both sides of a joint or splice of subfloor should be level to each other Level and support waste pipe cutout area greater than 5 5 The base is NOT to be suppo
21. limited warranty does not include labor transportation or other costs incurred in the removal and or reinstallation of the original unit and or installation of a replacement unit any costs relating to obtaining access for repair or loss of use damage including loss of sales profit or business advantage of any kind under any circumstances Bath units are excluded from any warranty coverage if any addition deletion or modification of any kind whatsoever has been made to the unit or to any component Warranty coverage is provided in the United States of America and Canada EXCLUSION OF IMPLIED WARRANTIES IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED ALTOGETHER OR TO THE FULL EXTENT ALLOWED BY LAW NOTICE This warranty gives you specific legal rights and you may also have other rights which vary from state to state There are no warranties applicable to Jacuzzi Whirlpool Bath products except as expressly stated herein or as implied by applicable state and federal laws The Company will not be responsible for any statements or representations made in any form that go beyond are broader than or are inconsistent with any authorized literature or specifications furnished by the Company Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you RETURN OF WAR
22. ower base does not drain properly rectify this condition before proceeding with theinstallation Jacuzzi Whirlpool Bath is not respon sible for removal and or reinstallation costs NOTE Watertight installation of the drain is the installer s responsibility Drain leakage is excluded from the Jacuzzi Whirlpool Bath warranty Replace the strainer and tape over the drain hole to prevent finishing material from entering drain 7 TILE CEMENT BOARD STUD GROUT SILICONE SEALANT SHIM IF NECESSARY DO NOT FILL 1 1 8 MAXIMUM NO MINIMUM CLEAN UP AFTER INSTALLATION To avoid dulling and scratching the acrylic surface of the base never use abrasive cleaners A mild liquid detergent and warm water clean soiled surfaces Remove spilled plaster with a wood or plastic edge Metal tools scratch the surface Spots left by plaster or grout can be removed if lightly rubbed with detergent on a damp cloth or sponge Paint tar or other difficult stains can be removed with paint thinner turpentine or isopropyl alcohol rubbing alcohol Minor scratches which do not penetrate the color finish can be removed by lightly sanding with 600 grit wet dry sandpaper You can restore the glossy finish to the acrylic surface of the base with a special compound Meguiar s 10 Mirror Glaze If not available use auto motive rubbing compound followed by an application of automotive paste wax Major
23. pening in the subfloor no less than 5 x 5 square This opening should be located on the center lines ofthe shower base drain hole See Product Chart The opening is to accommodate a 2 waste pipe The waste pipe should be 1 4 to 1 2 above the surface of the subfloor lt 3 90 NN 90 90 2 WASTE 5 x5 OPENING MIN AS POSSIBLE As shown in top view 1 2 copper pipes are provided to connectto the water supply Also provided are 2 loose 45 elbows as shown for installation in Detail 1 CAUTION A nonflammable protective barrier must be placed between soldering work and base unit to prevent damage to the base When connecting the supply lines the toe plate can be notched to accommodate the pipes The pipe underthe base can be cutto length To do so remove the pipe clamps under the base cutthe pipe and reinstall pipes STUD WALL NOT PROVIDED 45 ELBOW PROVIDED 2 DEATAIL 1 INSTALLATION INSTRUCTIONS STEP 2 Remove the stainless steel strainer from the drain assembly Disassemble the locknut and two gaskets from the back of the drain assembly Apply a 1 4 bead of caulking silicone to the drain hole and insert the drain assembly Replace the rubber washer fiber washer and lock nut in that order Hand tighten the locknut Remove excess sealant from finished side Apply a lubricant common household liquid soap works well to the inside of the rubber sea
24. ption or accessory was originally purchased by the user WARRANTY LIMITATIONS Our limited warranty does not cover defects damage or failure caused by the common carrier installer user or other person or resulting from without limitation any ofthe following careless handling lifting unit by plumbing abrading finish etc modification of any type for any reason including modification to meet local codes improper installation including installation not in accordance with instructions and specifications provided with the unit connections supplied by the installer of the equipment improper voltage supply or unauthorized electrical modification misuse incorrect operation or lack of proper routine maintenance operation of the unit without specified minimum amount of water or at inappropriate water temperature use of abrasive or improper cleaners or acts of God such as lightning floods earthquakes etc In addition THE COMPANY WILL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES or losses arising from any cause e g water damage to carpet ceiling loss of use etc including its own negligence damages to respecting or resulting from plated parts when pool and or spa chemicals are used in the unit optional bath equipment not manufactured by the Company but supplied by Dealer installer or the Company the unit s prior usage as an operational display or defects that should have been discovered before installation This
25. re the curved glass locates into the glazing channel Install bolt but do not tighten i BOLT 5 16 ae WASHER GLAZING CHANNEL STEP 6 Insert tower support rail into glass panel rail but do not tighten at this time GLASS PANEL SUPPORT RAIL TOWER SUPPORT RAIL STEP 7 Insert support rails into brackets in top moulding of tower but do not tighten at this time Front and tower support rails may have to be cut if they are too long TOWER SUPPORT RAIL FRONT RAIL GLASS PANEL SUPPORT RAIL STEP 8 Slide mounting bracket covers and mounting brackets onto front rail and tower support rail MOUNTING BRACKET EE COVER RAIL WALL MOUNTING BRACKET 2 WALL TOWER FIXED WALL AND CURVED GLASS INSTALLATION STEP 9 Place the front rail and tower support rail against the walls Check level and mark the position for the rail mounting bracket The screw position will be above the rail Drill the wall with a 3 16 bit and secure bracket with screws and wall anchors provided STEP 11 Secure the rails ATTACH RAIL BRACKET TO WALL SECURE RAIL TO BRACKET TURN CW TO TIGHTEN MOVE COVER CAP OVER BRACKET STEP 10 Adjust the rails until tower is vertical in 2 planes STEP 12 Tight
26. rted by the tile flange SPREAD MORTAR OR LEVELING COMPOUND ETC EVENLY OVER ENTIRE AREA 3 WALL BASE INSTALLATION STEP 4 With the drain fitting passing over the center of the drainpipe lower the shower base carefully into place push down firmly until the base is in place You must check the level of the base in two directions Do not lift a corner to level the base This will cause a loss of contact with the mortar Attach the shower base flange to the stud wall and blocking with self drilling screws included Use a minimum of 3 screws per flange section WHEN SCREWING FLANGE TO STUD WALL START WITH THIS SIDE Lc V i POSITION BASE OVER CENTER OF DRAIN PIPE AND SET INTO PLACE NOTE If there is any gap between base flange and stud or blocking shims MUST be used to prevent distortion or cracking of the flange TILE SHIM FLANGE TILE FLANGE GAP USE USE SCREWS SCREWS PROVIDED PROVIDED STUD STUD INCORRECT CORRECT STEP 5 With a large screwdriver and the tool included with the drain tighten the inside compression nut to seal the drain pipe connection After drain is fully installed test for proper drainage If the shower base does not drain properly rectify this condition before proceeding with the installation Jacuzzi Whirlpool Bath is no
27. s turn off hot and cold supplies Remove tower cover Disconnect the supply hoses from the valve and remove filter from the hose Clean any debris Reinstallation is the reverse of removal Turn on hot and cold supply and check for leaks PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT Jacuzzi Whirlpool Bath has obtained applicable code standards listings generally available on a national basis for products of this type Itis the responsibility of the installer owner to determine specific local code compliance prior to installation of the product Jacuzzi Whirlpool Bath makes no representation or warranty regarding and will not be responsible for any code compliance JACUZZI WHIRLPOOL BATH Jacuzzi Whirlpool Bath National Headquarters P O Drawer J Walnut Creek CA 94596 925 938 7070 Service Support Call 925 938 7411 Z 2002 Jacuzzi Whirlpool Bath 02230000 2 04 any Printed on Recycled Paper Printed in U S A 24 TOWER FIXTURES REPAIR PARTS H 5 p ACO 7 Part of U547000 8 PART OF D709827 10 WASHER PART OF 0709827 19 C546000 Lock Nut 1 2 NPT WP 5X G559000 Ring Compression SS 5X G560000 Washer Rubber 5X U546000 Part of U547000 Nut Transfer Valve Chrome U566000 Gasket 1 41 ID X 063 Thick U547000 Valve Mixer Transfer Assembly U550827 Part of U547000 567000Nut Mixer Valve Chrome U567000 Gasket
28. scratches and gouges which penetrate the acrylic surface require refinishing Ask your Jacuzzi Whirlpool Bath dealer for special instructions 3 WALL TOWER AND CURVED GLASS INSTALLATION STEP 1 Position the wall post so the edge of the post is set back 3 4 19 mm in from the finish wall FINISH m Ag 3 4 19 STEP 2 Level the post in its proper position and mark where screw holes areto be drilled Drill 3 16 holes and secure with wall anchors and screws provided Cut a 12 strip of tape provided and apply firmly over screw heads TAPE 3 PLACES STEP 3 Slide the glass panel into the wall post Make sure that the corner notch is positioned toward the base of the tower STEP 4 Place the tower onto base Ensure the curved glass locates into the glazing channel Install bolt but do not tighten BOLT 5 16 WASHER N GLAZING CHANNEL 3 WALL TOWER AND CURVED GLASS INSTALLATION STEP 5 Insert supportrails into brackets in top moulding oftower but do not tighten at this time TOWER SUPPORT RAIL FRONT RAIL STEP 6 Slide mounting bracket covers and mounting brackets onto front rail and tower support rail MOUNTING BRACKET B COVER RAIL WALL MOUNTING BRACKET
29. should be filed promptly thereafter It is the responsibility of the installer building contractor or user to provide access for service The Company is not responsible for any costs relating to obtaining access for repair The user shall bear such costs and if appropriate must seek recovery from the installer Damage occurring to the unit during installation is the responsibility of the installer and or building contractor and damage occurring thereafter is the responsibility of the user Failure of any optional equipment is the sole responsibility of the equipment manufacturer Options and accessories manufactured by the Company are warranted for ninety 90 days from the original date of purchase for parts only The Distributor or Dealer is responsible for knowing local code requirements and notifying the installing contractor and or user of these requirements at the time of purchase The Company is not responsible for costs to modify any product to obtain any code approval such as city county or state building codes in U S A or municipal or provincial codes in Canada WARRANTY SERVICE For the customer s benefit the Company maintains a list of independent service personnel to perform required warranty service repairs Such firms are not agents or representatives of the Company and cannot bind the Company by words or conduct The Company will provide the warranty service described above when the following conditions have been met the failure
30. t o lt ggg 8 8B 8 323 29 w Cc 3 5 5 gt pre g z A 9 zx NO lt 5 55 38 SO US N 935 S NS 2 8 S 0 N PE E o 2950 o 9 v 2 o9 gt 9 2 oe lt 9 5 2 93 g o0 o 5 5 e 9 2S D E 3 og o S lt o o F 5 9 go 9 3 3 2 5 2 HIVE 100d THIHM IZZnowr RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer building contractor who acts on behalf of the user They are responsible for ensuring the unit is free of defect or damage Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility In the event of a problem the unit must not be installed The Company is not responsible for failures or damage that could have been discovered repaired or avoided by proper inspection and testing prior to installation Damage occurring in transit is the responsibility of the carrier The user or installer MUST open the crate and inspect the unit for damage when it is delivered If damage is discovered it must be reported immediately to the seller and the carrier in writing and an inspection requested Failure of the carrier to respond should be reported to the seller and the carrier Your freight claims
31. t respon sible for removal and or reinstallation costs NOTE Watertight installation of the drain is the installer s responsibility Drain leakage is excluded from the Jacuzzi Whirlpool Bath warranty Replace the strainer and tape over the drain hole to prevent finishing material from entering drain TIGHTEN SEALING NUT INCLUDED 3 WALL BASE INSTALLATION STEP 6 With the drain fitting passing over the center of the drainpipe lower the shower base carefully into place push down firmly until the base is in place You must check the level of the base in two directions Do not lift a corner to level the base This will cause a loss of contact with the mortar Attach the shower base flange to the stud wall and blocking with self drilling screws included Use a minimum of 3 screws per flange section CEMENT BOARD STUD al NOTE If there is any gap between base flange and stud or blocking shims MUST be used to prevent distortion or cracking of the flange SILICONE SEALANT 1 4 MINIMUM GAP TILE 47 BOARD 1 4 MINIMUM GAP TILE ADHESIVE STUD SILICONE 1 8 GAP SEALANT STEP 7 With a large screwdriver and the tool included with the drain tighten the inside compression nut to seal the drain pipe connection After drain is fully installed test for proper drainage If the sh
32. tighten the inside compression nut to seal the drain pipe connection After drain is fully installed test for proper drainage If the shower base does not drain properly rectify this condition before proceeding with the installation Jacuzzi Whirlpool Bath is not respon sible for removal and or reinstallation costs NOTE Watertight installation of the drain is the installer s responsibility Drain leakage is excluded from the Jacuzzi Whirlpool Bath warranty Replace the strainer and tape over the drain hole to prevent finishing material from entering drain Ia TIGHTEN SEALING NUT Lact INCLUDED DRAIN PIPE AND SET INTO PLACE NOTE If there is any gap between base flange and stud or blocking shims MUST be used to prevent distortion or cracking of the flange TILE SHIM FLANGE TILE FLANGE GAP USE USE SCREWS SCREWS PROVIDED PROVIDED STUD STUD INCORRECT CORRECT 2 WALL BASE INSTALLATION STEP 6 Place cement board or equivalent on top of shower base flange and secure to studwall CEMENT BOARD STUD STEP 7 Apply tile or other finishing material leaving a 1 8 gap between the finishing material and the shower base flange lip Seal this gap with silicone sealant Leave a minimum 1 4 gap at the back and front corners of the shower base to allow drainage from leakage through unsealed tiled grout TILE N H 1 4 MINIMUM GAP CEMENT 1 B
33. tin 827 Chrome 938 Timber 959 White 14 For colors for U171XXX Shower Base substitute XXX for Standard 959 White 958 Almond 969 Oyster 945 Silver High Fashion 917 Black 949 Rose 951 Shell 978 Forest Green 984 Shy Blue 999 Sand 28 Jacuzzi Whirlpool Bath Limited Warranty Designer Collection Shower Product WARRANTY COVERAGE Jacuzzi Whirlpool Bath the offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Designer Collection Bath Product unit who purchases the product for personal single family use user The Company will repair or replace at its option the unit or its equipment in accordance with the following terms and conditions TWO YEAR LIMITED WARRANTY ON BATHS Our limited warranty on Designer Collection Bath products is for two 2 years Our warranty covers the unit and factory installed components against defects in material or workmanship Warranty coverage begins on the date the unit was originally purchased by the user NINETY DAY PARTS ONLY LIMITED WARRANTY ON OPTIONS AND ACCESSORIES Our limited warranty on options and accessories manufactured by the Company is for ninety 90 days for parts only Our warranty covers options and accessories manufactured by the Company against defects of material or workmanship Warranty coverage begins on the date the o
34. tower cover STEP 17 Install tower cover as shown Insert cover at top first TOWER TOP PLATE TOWER COVER INSERT THIS SIDE FIRST TOWER COVER STEP 18 Seal all around the base of tower with silicone sealant Also seal the inside of both wall posts glass post and the bottom of both glass panels on the inside only APPLY SEALANT ALONG BASE AND SIDE OF WALL POST 3 HK 1 APPLY SEALANT SN ALONG BASE APPLY SEALANT OF GLASS ALONG BASE OF GLASS UN AE APPLY SEALANT APPLY SEALANT GROUND sr ALLAROUND ALONG BASE TOWERBASE AND SIDE OF WALL POST RAILS NOT SHOWN TOP VIEW 3 WALL SPECIFICATIONS Important Read complete instructions before beginning installation Each unit arrives ready for installation equipped with base glass and associated hardware Remove the unit from the carton Retain the shipping carton until satisfactory inspection of the product has been made Immediately upon receipt inspect the base and other components before installing Check all carton inserts for parts and hardware Should inspection reveal any damage or defect in any component do install the unit Damage or defect to any component claimed after the unit is installed is excluded from the warranty Jacuzzi Whirlpool Bath s responsibility for shipping damage ceases upon delivery of the products in good order to the carrier Re
Download Pdf Manuals
Related Search