Hunter Fan 45007 Fan User Manual
Contents
1. Check each connection to make sure no bare wire or wire strands are visible Push all wires and wire connectors except for the white antenna wire from the receiver back through the ceiling plate into the outlet box 8 45007 01 11 02 07 Hunter Fan Company 6 2 6 3 6 4 6 Installing the Canopy and Canopy Trim Ring Partially install two canopy screws about 2 full turns in the hanger bracket Raise the canopy over the hanger bracket Align partially installed screws with key slots in canopy Twist canopy clockwise to secure Install third amp fourth canopy screw in round hole on canopy Securely tighten all four screws Using both hands push the canopy trim ring up to the top of the canopy Twist canopy trim ring clockwise to secure the canopy Should you need to remove the canopy trim ring follow these steps 1 Twist canopy trim ring counterclockwise until it releases from canopy Step 6 5 9 Steps 6 1 6 2 Hanger Bracket gt Canopy Trim 45007 01 11 02 07 Hunter Fan Company 7 Assembling the Blades 7 1 Insert each blade into slot Align the holes on the blade with the holes on the blade ring 7 2 Attach the blade to the blade ring using the blade assembly screws 7 3 Repeat for each blade 10 45007 01 11 02 07 Hunter Fan Company 8 Completing Your Installation With a Bowl Light Fixture You2. installation and Operation manual for Hunter For Your Records and Warranty Assistance Model Name Ceiling Fans Catalog Model No Serial No Date Purchased Where Purchased For reference also attach your receipt or a TY P F 3 AYAN O d e S copy of your receipt to the manual 45007 01 11 02 07 Welcome Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years This installation and operation manual gives you complete instructions for installing and operating your fan We are proud of our work We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world Before installing your fan for your records and warranty assistance record information from the carton and Hunter nameplate label located on the top of the fan motor housing Cautions and Warnings Table Of Contents e READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING INSTALLATION SAVE THESE INSTRUCTIONS e Use only Hunter replacement parts 2 Installing the Hanger Bracket e To reduce the risk of personal injury attach the fan directly to the 3 Assembling and Hanging the Fan 6 support structure of the building according to these instructions and use only the hardware supplied To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the
3. keyholes in the light kit assembly with the two preinstalled housing assembly screws and turn the light kit assembly clockwise until the screws are resting in the narrow end of the keyhole slots T Light Kit 8 7 Tighten the prinstalled assembly screws and install the Assembly third assembly screw Steps 8 5 8 7 8 8 Install B10 candelabra bulbs 60 Watt Maximum into Keyhole Slots the sockets 8 9 Hold the glass bowl up with the holes in the glass bowl aligned with the holes in the metal rods Assembly Screw 8 10 Install the decorative screws into the metal rods to secure y the glass bowl in place Metal Rod Light Bulbs B10 Candelabra Based 60 Watt Maximum Decorative Screw ae Bowl Steps 8 8 8 10 12 45007 01 11 02 07 Hunter Fan Company 9 1 9 Operating the Remote Control and Mounting the Holder The remote has individual buttons for setting fan speed and light intensity Refer to the figure on the right Note For best operation start the fan by pressing high then select your desired speed The light button turns the light Push the light button again to turn off the light When necessary replace the battery with a 9 volt alkaline battery You can mount the remote holder to any toggle switch plate with the screws already in the switch plate Or you can simply mount the remote holder on the wall
4. 11 02 07 Hunter Fan Company 11 Troubleshooting Problem Nothing happens fan does not move 1 Turn power on replace fuse or reset breaker 2 Loosen canopy check all connections according to the wiring the fan section 3 Check the plug connection in the switch housing 4 Push motor reversing switch firmly left or right to ensure that the switch is engaged 5 Pull the pull chain to ensure it is on 6 Remove the shipping bumpers Problem Noisy operation 1 Tighten the blade bracket screws until snug 2 Check to see if the blade is cracked If so replace all the blades Problem Excessive wobbling 1 If your fan wobbles when operating use the enclosed balancing kit and instructions to balance the fan 2 Tighten all blade iron screws 3 Turn power off support fan very carefully and check that the hanger ball is properly seated If you need parts or service assistance please call 888 830 1326 or visit us at our Web site at http www hunterfan com Hunter Fan Company 2500 Frisco Avenue Memphis Tennessee 38114 15 45007 01 11 02 07 Hunter Fan Company
5. Fan Speed High Fan Speed Low Fan Speed Medium Fan Off Fan Light Steps 9 1 9 2 _ 13 45007 01 11 02 07 Hunter Fan Company 10 1 10 2 10 3 10 4 10 Operating and Cleaning Your Ceiling Fan Turn on electrical power to the fan Ceiling fans work best by blowing air downward counterclockwise blade rotation in warm weather to cool the room with a direct breeze In winter having the fan draw air upward clockwise blade rotation will distribute the warmer air trapped at the ceiling around the room without causing a draft For cleaning finishes use a soft brush or lint free cloth to prevent scratching A vacuum cleaner brush nozzle can remove heavier dust Remove surface smudges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth You may use an artistic agent but never abrasive cleaning agents as In warm weather use they will damage the finish downward air flow pattern Clean wood finish blades with a furniture polishing cloth Occasionally apply a light coat of furniture polish for added protection and beauty Clean painted and high gloss blades in the same manner as the fan finish In cold weather use upward air flow pattern To Change Airflow Direction Turn the fan off and let it come to a complete stop Slide the reversing switch on the fan to the opposite position Restart fan Reversing Switch 14 45007 01
6. and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician 5 1 5 2 5 3 5 5 Make sure the power is still off Position the receiver in the canopy so that the antenna is close to the edge of the ceiling plate for clear reception To connect the wires hold the bare metal leads together and place a wire connector over them then twist clockwise until tight For all these connections use the wire connectors provided A CAUTION Be sure no bare wire or wire strands are visible after making connections Using a large wire connector connect the ground wire from the ceiling to the green ground wire from the ceiling plate and the green ground wire from the downrod Using the large wire connectors connect the white wire and the black wire from the ceiling as follows e The white common power wire from the ceiling to the white wire from the receiver marked on red tag NEUTRAL IN e The black power wire from the ceiling to the black wire from the receiver marked on red tag LIVE IN Using the small wire connectors connect the wires from the fan as follows e The black white wire from the fan to the red wire from the receiver marked on white tag LIGHT OUT e The black wire from the fan to the black wire from the receiver marked on white tag FAN OUT e The white wire from the fan to the white wire from the receiver marked on white tag COMMON OUT
7. e the position of the DIP switches in the remote transmitter and the receiver Make sure that the DIP switches match in the remote receiver and transmitter If they don t match the transmitter will not function Transmitter DIP switches 4 2 There is a toggle switch beside the DIP switches on the transmitter Move the toggle switch toward the side that reads CFL if you are going to operate the fan with CFL bulbs Move the switch to the INC side if you are going to use incandescent bulbs Example DIP Switch Settings 4 3 Install the included 9 volt battery into the transmitter Receiver 1 Receiver 2 A CAUTION The remote control device complies with part 15 of the FCC rules Changes or modifications not expressly approved by Hunter Fan Company could void your authority to operate this equipment neste l a DIP Switches DIP Switches Operation is subject to the following two conditions Set to 0111 Set to 0100 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may Transmitter 1 Transmitter 2 cause undesired operation A WARNING Use only the Hunter Fan speed control supplied with this fan DIP Switches DIP Switches Set to 0111 Set to 0100 7 45007 01 11 02 07 Hunter Fan Company 5 Wiring the Fan Step 5 4 Step 5 5 Antenna Receiver Step 5 6 All wiring must be in accordance with national
8. embly is fully installed 2 3 threads on the pipe will still be visible this is normal Securely retighten the set screw with a wrench or pliers A CAUTION The adapter has a special coating on the threads Do not remove this coating the coating prevents the downrod from unscrewing Once assembled do not remove the downrod A WARNING Do not carry or lift fan by canopy Raise the fan and place the ball into the hanger bracket Align the notch on the ball with the indent in the hanger bracket Rotate the fan until you hear the notch pop into place Go to 4 e Wiring the Fan A WARNING Fan may fall if not assembled as directed in these installation instructions 6 Steps 3 1 3 3 m Downrod lt Canopy with Washer va Canopy Trim Adapter Ring Steps 3 4 3 5 45007 01 11 02 07 Hunter Fan Company 4 Setting the Remote Transmitter and Receiver Setting DIP switches When two or more fans are located near each other you may desire to have the receiver transmitter for each fan set to a different code so that the operation of one fan does not affect the operation of the other fans The DIP switches for the receiver are located on the flat surface of the receiver The DIP switches for the transmitter are in the the battery compartment 4 1 IMPORTANT Before you change the DIP switch settings make sure the battery is not connected to the transmitter Chang
9. outlet box and associated wall switch location If you cannot lock 6 Installing the Canopy and Canopy the circuit breakers in the off position securely fasten a prominent Trim Ring warning device such as a tag to the service panel 7 Assembling the Blades All wiring must be in accordance with national and local electrical 8 Completing Your Installation With a codes and ANSI NFPA 70 If you are unfamiliar with wiring use a Bowl Light Fixture qualified electrician To reduce the risk of personal injury do not bend the blade attachment system when installing balancing or cleaning the fan Never insert foreign objects between rotating fan blades To reduce the risk of fire electrical shock or motor damage do not use a solid state speed control with this fan Use only Hunter speed controls 1 Getting Ready 4 Setting the Remote Transmitter and Receiver 5 e Wiring the Fan 9 e Operating the Remote Control and Mounting the Holder 10 Operating and Cleaning Your Ceiling 2007 Hunter Fan Company 2 45007 01 11 02 07 Hunter Fan Company Installer s Choice and Optional Accessories Support Brace Ceiling Standard Outlet Box Mounting gt Style Standard Mounting hangs from the ceiling by a downrod included Mounting Angled Mounting recommended for a vaulted or angled ceiling Understanding Mounting and Installers Choice Hunter s
10. patented 2 position mounting system provides you maximum installation flexibility and ease You can install your Hunter fan in one of two ways depending on ceiling height and your preference Standard or Angled mounting The steps in this manual include instructions for both Installer s Choice mounting methods Considering Optional Accessories Consider using Hunter s optional accessories including a wall mounted or remote speed control To install and use the accessories follow the instructions included with each product For quiet and optimum performance of your Hunter fan use only Hunter speed controls For ceilings higher than 8 feet you can purchase Hunter extension downrods All Hunter fans use sturdy 3 4 diameter pipe to assure stability and wobble free performance A CAUTION To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied 3 45007 01 11 02 07 Hunter Fan Company l Getting Ready To install a ceiling fan be sure you can do the following e Locate the ceiling joist or other suitable support in ceiling e Drill holes for and install wood screws e Identify and connect electrical wires e Lift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering the Tools You will need the following tools for ins
11. r Hunter fan comes with an integrated light fixture assembly A WARNING Use only the light fixture supplied with this fan model 8 1 To attach the heat shield assembly partially install two housing assembly screws into the switch housing mounting plate 8 2 Feed the upper plug connector through the center opening of the shield 8 3 Align the keyhole slots in the housing with the assembly screws 8 4 Turn the housing counterclockwise until the housing assembly screws are firmly situated in the narrow end of the keyhole slots Install the remaining screw into the housing Tighten all three screws firmly Steps 8 1 8 A CAUTION Make sure the heat shield assembly is securely Assembly or attached to the housing mounting plate Failure to properly attach Screw are and tighten all three assembly screws could result in the heat shield E Assembly assembly and light fixture falling lI 45007 01 11 02 07 Hunter Fan Company 8 e Completing Your Installation With a Bowl Light Fixture Continued 8 5 To attach the light kit connect the upper plug connector from the heat shield assembly to the lower plug connector in the light kit assembly Note Both plug connectors are polarized and will only fit together one way Make sure the connectors are properly aligned before connecting them Incorrect connection could cause improper operation and damage to the Hed Shield 7 product Assembly 8 6 Align the
12. rom the outlet box down through the hole in the middle of the hanger bracket you drilled in the wood support structure For proper alignment use slotted holes directly across from each other If you are installing the fan on an ANGLED ceiling be sure to orient the hanger bracket as shown in Illustration 2 3 left or right view Note The isolators should be flush against the ceiling Place a flat washer on each of the two 3 screws and pass the screws through the slotted holes in the hanger bracket into the pilot holes you drilled Tighten the screws into the 9 64 pilot holes do not use lubricants on the screws Do not over tighten Flat Washer af Steps 2 2 2 4 Ceiling Peak Large Opening 3 Screw LEFT S ps EL ps ps ps ps ps ps E ps ps ps ps ps ps ps Step 2 3 Angled Ceiling Only m p 5 45007 01 11 02 07 Hunter Fan Company Ceiling Peak Large 3 1 3 2 3 3 3 4 3 5 3 Assembling and Hanging the Fan To assemble fan to hang down from a flat or angled ceiling place the canopy and canopy trim ring around the adapter so that they rest on the fan assembly Feed the wires from the fan through the downrod Note Make sure all the wires are on the same side of the metal dowel pin inside the dowrod Loosen the square head set screw on the adapter to install the pipe and ball assembly Note When the pipe and ball ass
13. talling the fan e Electric drill with 9 64 bit e Standard screwdriver magnetic tip recommended e Phillips head screwdriver magnetic tip recommended e Wrench or pliers e Ladder height dependent upon installation site Checking Your Fan Parts Carefully unpack your fan to avoid damage to the fan parts Refer to the included Parts Guide Check for any shipping damage to the motor or fan blades If any parts are missing or damaged contact your Hunter dealer or call Hunter Technical Support Department at 888 830 1326 Preparing the Fan Site Before you begin installing the fan follow all the instructions in the pullout sheet called Preparing the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings 4 Installing Multiple Fans If you are installing more than one fan keep the fan blades and blade irons if applicable in sets as they were shipped 45007 01 11 02 07 Hunter Fan Company 2 1 2 2 2 4 Align the slotted holes in the hanger bracket with the pilot holes 2 Installing the Hanger Bracket Drill two pilot holes into the wood support structure through the outermost holes in the outlet box The pilot holes should be 9 64 l Isolator in diameter Note Your fan comes with four pre installed neoprene noise Aka racKe isolators Thread the lead wires f
Download Pdf Manuals
Related Search