Hunter Fan 42404-01 Fan User Manual
Contents
1. Partially install a canopy screw into the side opposite the ceiling plate tabs Partially install another canopy screw into the hole between the two ceiling plate tabs Securely tighten both screws Step 6 4 9 42404 01 01 04 10 Hunter Fan Company Step 6 1 Step 6 3 7 Assembling the Blades Hunter fans use several styles of fan blade irons brackets that hold the blade to the fan Step 7 1 Detail 7 1 Your fan may include blade grommets If your fan has grommets insert them by hand into the holes on the blades 7 2 Attach each blade to a blade iron using three blade assembly screws If you used grommets the blades may appear slightly loose after screws are tightened This is normal 7 3 Some blade mounting screws are installed in the motor to secure shipping blocks Remove the blade mounting screws and rubber bumpers from the motor Save the screws and discard the bumpers 7 4 For each blade insert one blade mounting screw through the blade iron and attach lightly to the fan Insert the second blade mounting screw then securely tighten both mounting screws Blade Assembly Steps 7 1 7 2 Use with grommet screws Use without grommet Blade Mounting Screw I Step 7 4 42404 01 01 04 10 Hunter Fan Company K2 8 Installing the Light Kit A WARNING Use only the light fixture supplied with this fan mo2. For Your Records and P Warranty Assistance AYA O e 2 S For reference also attach your receipt or a copy J j lt uD E F Ba NE AT of your receipt to the manual Owner s Guide and Installation Manual 7 z Q oF Q T SINCE 1886 a Form 42404 01 20100104 2010 Hunter Fan Co Welcome Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years This installation and operation manual gives you complete instructions for installing and operating your fan We are proud of our work We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world Before installing your fan for your records and warranty assistance record information from the carton and Hunter nameplate label located on the top of the fan motor housing Cautions and Warnings e Read this entire manual carefully before beginning installation Save these instructions Use only Hunter replacement parts To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the 1 Getting Ready outlet box and associated wall switch location If you cannot lock the circuit breakers in the of
3. Consider using Hunter s optional accessories including a wall mounted or remote speed control To install and use the accessories follow the instructions included with each product For quiet and optimum performance of your Hunter fan use only Hunter speed controls For ceilings higher than 8 feet you can purchase Hunter extension downrods All Hunter fans use sturdy 3 4 diameter pipe to assure stability and wobble free performance 3 10 Low Profile Mounting fits close to the ceiling recommended for ceilings less than 8 feet high 12 Standard Mounting hangs from the ceiling by a downrod included recommended for ceilings 8 feet or higher 34 Max Angle Mounting recommended for a vaulted or angled ceiling 42404 01 01 04 10 Hunter Fan Company K2 l Getting Ready To install a ceiling fan be sure you can do the following e Locate the ceiling joist or other suitable support in ceiling e Drill holes for and install wood screws e Identify and connect electrical wires e Lift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering the Tools You will need the following tools for installing the fan e Electric drill with 9 64 bit e Standard screwdriver magnetic tip recommended e Phillips head screwdriver magnetic tip recommended e Wrench or pliers e Ladder height
4. dependent upon installation site Installing Multiple Fans If you are installing more than Checking Your Fan Parts one fan keep the fan blades and Carefully unpack your fan to avoid damage to the fan parts Refer to blade irons if applicable in sets the included Parts Guide Check for any shipping damage to the motor as they were shipped or fan blades If any parts are missing or damaged contact your Hunter dealer or call Hunter Technical Support Department at 866 268 1936 Preparing the Fan Site Before you begin installing the fan follow all the instructions in the pullout sheet called Preparing the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings 4 42404 01 01 04 10 Hunter Fan Company K2 2 1 2 3 2 4 2 Installing the Ceiling Plate Isolator amp Drill two pilot holes into the wood support structure through the outermost holes in the outlet box The pilot holes should be 9 64 in diameter Your fan comes with two neoprene noise isolators Isolators Position the isolators between the ceiling plate and ceiling by inserting the raised areas on each isolator into the holes in the ceiling plate Thread the lead wires from the outlet box down through the hole in the middle of the ceiling plate Align the slotted holes in the ceiling plate wi
5. to you can control the fan and light separately using two wall switches To do so connect the wires as follows e The bare or green ground wire from the ceiling to the green nd wire from the ceiling plate and the green ground wire the fan e The white wire from the ceiling to the white wire from the fan e The black wire from the ceiling to the black wire from the fan e The black white wire from the fan to the wire for the wall switch Alternatively you can control both fan and light with one switch To do so connect the wires as follows e The bare or green ground wire from the ceiling to the green nd wire from the ceiling plate and the green ground wire the fan e The white wire from the ceiling to the white wire from the fan e The black wire from the ceiling to the black and the black white from the fan ect the wires hold the bare metal leads together and place a wire connector over them then twist clockwise until tight A CAUTION Be sure no bare wire or wire strands are visible after making connections wires and wire connectors back into the ceiling plate 8 42404 01 01 04 10 Hunter Fan Company a J 6 1 6 3 6 4 6 Installing the Canopy Rotate the hanger ball so the tab in the canopy is secure in the groove in the hanger ball A WARNING Failure to complete this step could cause fan to fall Lift the fan and align the canopy screw holes with the mounting holes on the ceiling plate
6. 4 Wrap the braided cable around the support brace once creating a complete circle 4 5 Hook the looped end of the cable over the wood screw so that the braided cable lies between the washer and the support brace 4 6 Tighten the loop and secure the screw and washer all the way down to the support brace 4 7 Coil up the excess cable 4 8 Return to the fan so you can complete the fan wiring Steps 4 2 4 3 3mm lt Support Brace Outlet Box Ceiling Step 4 1 Steps 4 4 4 5 is 7 42404 01 01 04 10 Hunter Fan Company K2 S N L mm Sn 5 e Wiri Step 5 3 All wiring m codes and A qualified ele decide grou from grou from Wire Connector wire 5 5 To conn 5 6 Push all ng the Fan ust be in accordance with national and local electrical NSI NFPA 70 If you are unfamiliar with wiring use a ctrician Wall switches are not included Select an acceptable general use switch in accordance with national and local electrical codes 5 1 Disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location 5 2 Decide how you want to set up the fan and light controls You can control the fan and or lights together or separately using one or two wall switches Follow Step 5 3 OR Step 5 4 depending on what you If you want
7. 8 6 housing with three housing assembly screws Plug Connec Housing Detail Assembly Screw lI 42404 01 01 04 10 Hunter Fan Company Step 8 7 8 8 8 Installing the Light Kit Continued 8 7 To install the glass shades insert each glass shade in a shade cup 8 8 Install and tighten the three thumbscrews Do not over tighten 8 9 Install medium base incandescent light bulbs 60 watt maximum each Shade Cup Glass Shade Thumb Screw Note In compliance with Canadian federal energy regulations this ceiling fan contains a device that restricts the light kit to a maximum of 190 Watts Exceeding that limit or the marked limit on this product may result in fire hazard or improper operation 12 42404 01 01 04 10 Hunter Fan Company K2 9 1 OZ Pa 9 4 9 6 9 Operating and Cleaning Your Ceiling Fan Turn on electrical power to the fan The fan pull chain controls power to the fan The pull chain has four settings in sequence High Medium Low and Off e Pull the chain slowly to change settings e Release slowly to prevent the chain from recoiling into the blades e The chain uses a breakaway connector that separates if the chain is jerked If this happens simply reinsert the chain into the connector The light pull chain controls power to the light The pull chain has two settings On and Off Ceiling fans
8. del 8 1 To attach the upper switch housing partially install two housing assembly screws into the switch housing mounting plate 8 2 Feed the upper plug connector through the center opening of the housing 8 3 Align the keyhole slots in the housing with the housing assembly screws 8 4 Turn the housing counterclockwise until the housing assembly screws are firmly situated in the narrow end of the keyhole slots Install the remaining housing assembly screw into the housing Tighten all three screws firmly Steps 8 1 8 3 A CAUTION Make sure the upper switch housing is securely attached Housing to the switch housing mounting plate Failure to properly attach and Assembly Upper tighten all three assembly screws could result in the switch housing and Screw e light fixture falling 8 5 To attach the lower switch housing connect the upper plug connector from the motor to the lower plug connector in the lower switch housing assembly Plug Connector Note Both plug connectors are polarized and will only fit together one way Make sure the connectors are properly aligned before connecting them Incorrect connection could cause improper operation and damage to the product Lower Switch 8 6 Place the lower switch housing assembly over the upper switch Housing housing Align the side screw holes in the upper and lower switch d housings Attach the lower switch housing to the upper switch Steps 8 5
9. eads on the pipe will still be visible this is normal Securely retighten the set screw with a wrench or pliers Skip to Step 3 5 A CAUTION The adapter has a special coating on the threads Do not remove this coating the coating prevents the downrod from unscrewing Once assembled do not remove the downrod Note For low profile mounting the downrod is replaced with the low profile washer See Steps 3 3 3 4 3 3 Place the low profile washer into the canopy Be sure the green ground wire is pointing up toward the ceiling 3 4 Align the holes in the washer with the holes in the adapter Assemble securely with three 8 32 x 3 4 screws 3 5 Raise the fan and align the slots in the canopy with the tabs on th ceiling plate A WARNING Fan may fall if not assembled as directed in these installation instructions Ceiling Plate Tabs ae Canopy Slots 42404 01 01 04 10 Hunter Fan Company 4 Securing Fan to Secondary Support System 4 1 Find the looped end of the braided cable and insert it through the ceiling plate and one of the holes in the outlet box into the ceiling 4 2 Access the support brace in the ceiling You may not be able to do this from below the ceiling depending on your installation site 4 3 Drive a 10 x 38mm 1 1 2 wood screw and washer into the side of the brace that holds the outlet box Leave 3mm 1 8 of space between the support brace and the washer 4
10. f position securely fasten a prominent warning device such as a tag to the service panel All wiring must be in accordance with national and local electrical 4 e Securing Fan to Secondary codes and ANSI NFPA 70 If you are unfamiliar with wiring use a Support System qualified electrician 5 e Wiring the Fan To reduce the risk of personal injury do not bend the blade attachment system when installing balancing or cleaning the fan Never insert foreign objects between rotating fan blades To reduce the risk of fire electrical shock or motor damage do not 8 Installing the Light Kit use a solid state speed control with this fan Use only Hunter speed 9 e Operating and Cleaning controls Your Ceiling Fan Table of Contents 2 Installing the Ceiling Plate 3 Assembling and Hanging the Fan 6 Installing the Canopy 7 Assembling the Blades 10 Troubleshooting 2010 Hunter Fan Company 2 42404 01 01 04 10 Hunter Fan Company K2 Installer s Choice and Optional Accessories Understanding Mounting and Installers Choice Hunter s patented 3 position mounting system provides you maximum installation flexibility and ease You can install your Hunter fan in one of three ways depending on ceiling height and your preference Low Profile Standard or Angle mounting The steps in this manual include instructions for all three Installer s Choice mounting methods Considering Optional Accessories
11. th the pilot holes you drilled in the wood support structure For proper alignment use slotted holes directly across from each other Note The isolators should be flush against the ceiling Place a flat washer on each of the two 3 wood screws and pass the screws through the slotted holes in the ceiling plate into the pilot holes you drilled Tighten the screws into the 9 64 pilot holes do not use lubricants on the screws Do not over tighten Flat Washer 3 Wood Screw eee HFVHEOUUNURURUUD SU eee 5 42404 01 01 04 10 Hunter Fan Company K2 Ceiling Plate A I 1 I 1 le ee coed tof room tfo E Steps 2 3 2 5 Towards Ceiling Peak For Angled Ceilings Be sure to orient the ceiling plate so that the two tabs are pointing towards the ceiling peak 3 Assembling and Hanging the Fan Steps 3 1 3 2 lt m Downrod T Low Profile Washer 8 32 x 3 4 Screw You can assemble your fan for standard mounting steps 3 1 3 2 or for low profile mounting steps 3 3 3 4 3 1 To assemble fan to hang down from a flat or angled ceiling insert the downrod through the canopy Feed the wires from the fan through the downrod 3 2 Loosen the square head set screw on the adapter to install the pipe and ball assembly Note When the pipe and ball assembly is fully installed 2 3 thr
12. witch housing 4 Push motor reversing switch firmly left or right to ensure that the switch is engaged 5 Pull the pull chain to ensure it is on 6 Remove the shipping bumpers Problem Noisy operation 1 Tighten the blade assembly screws and blade iron armature screws until snug 2 Check to see if the blade is cracked If so replace all the blades Problem Excessive wobbling 1 If your fan wobbles when operating use the enclosed balancing kit and instructions to balance the fan 2 Tighten all blade iron screws 3 Turn power off support fan very carefully and check that the hanger ball is properly seated Problem Lights turn off when installed or dim when turned on 1 Check to make sure the wattage and type of light bulbs installed match the specifications on the light socket Problem Lights shut off suddenly 1 Turn the power to the fan off at the wall switch Wait 30 seconds then resume power to the fan If you need parts or service assistance please call 866 268 1936 or visit us at our Web site at http www hunterfan com Hunter Fan Company 7130 Goodlett Farms Parkway 400 Memphis Tennessee 38016 14 42404 01 01 04 10 Hunter Fan Company K2
13. work best by blowing air downward counterclockwise blade rotation in warm weather to cool the room with a direct breeze In cold weather having the fan draw air upward clockwise blade rotation will distribute the warmer air trapped at the ceiling around the room without causing a draft For cleaning finishes use a soft brush or lint free cloth to prevent scratching A vacuum cleaner brush nozzle can remove heavier dust Remove surface smudges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth You may use an artistic agent but never abrasive cleaning agents as they will damage the finish Clean wood finish blades with a furniture polishing cloth Occasionally apply a light coat of furniture polish for added protection and beauty Clean painted and high gloss blades in the Same manner as the fan finish To Change Airflow Direction Turn the fan off and let it come to a complete stop Slide the reversing switch on the fan to the opposite position Restart fan Reversing Switch 13 42404 01 01 04 10 Hunter Fan Company K2 In warm weather use downward air flow pattern In cold weather use upward air flow pattern 10 Troubleshooting Problem Nothing happens fan does not move 1 Turn power on replace fuse or reset breaker 2 Loosen canopy check all connections according to the wiring the fan section 3 Check the plug connection in the s
Download Pdf Manuals
Related Search