Haier 50FREE-3B Washer User Manual
Contents
1. Wash timer Wash selector Spin timer Ficure 4 indi a installati To set to below 2 minute Strong current to set to below 1 minute igure 1 indicates the ex factory installation ee EN fst ae i Minute ien KSE current frst set i 2 minute then position of the drain hose l Si sectional ven the service lf ofthe timer the service life of the timer s ge fangheok slr orra N f Extend the drain hose from the side of spin tub P T STANDARD A i Lon wards 5 JI Ns lk IN Take off the drainhose from the hanging VEES I se Baan hole of thecabinet Pull thedrain hose TT j Take off 12 nO D g fixing hook outwards gently to takeout w the drain hose NA WASH TIMER WASH SELECTOR 7 the drain hose from the twofixing hooks f Brankas amanin PERREN n As per Figure 2 Figure 1 fixing hook Figure 2 Rotate the drain hose fixing hook for 90 H to take it out from theinstallation hole zz EZ As per Figure 3 a i i K alae Wash Install the two drain hose fixing hooks taken pa T out into the installation hole at the other side of a HAEN dee the base frame to aim at the installation hole hook for 0 Fee hook for 90 yp A 1 Inlet selector accurately you can lean the washing machine WZ as H 1 Set inlet selector to Wash side Figure 1 PAI forward slightly Then rotatefor 90 As per Figure 4 Paok downwards Insert the2. actions may result in damage of the machine or injure the personal safety ofthe user Please check if the power receptacle has good earthing condition before using to guarantee your safety Haier Safety precautions Haier Please insert the power cord into When the machine is normally special receptacle with rated vol using please put the power plug tage Be sure to use single phase at the location easily to be insert three pins receptacle The earthing ed and extracted by hand Be sure terminal of the receptacle must be to pull the plug off when there s earthed reliably If possible please power failure or the machine is adopt electric leakage protector being moved cleaned or when it is idle E 1 Put the laundries into the spin tub evenly and smoothly 2 Press the gland in the tub properly Close the inner and outer cover of the spin tub If the supply cord is damaged it must be replaced by the manufacturer or its service agent ora similarly qualified person in order to avoid a hazard q 3 Spin X Select suitable spin time according to the laundries and do spinning Do not put the machine at damp place like the bathroom Never e During spinning if there is abnormal sound it is generally owing to wash it with water Do not place J slanting placement of the laundries Please stop the machine and wet laundries on the control panel lt 6 reorder the laundries In spinning it will pause the work if
3. water with hand For those laundries with heavy soil please first remove the dirt like mud or dust For the parts with heavy soil please apply detergent on them in advance which can make it easier to remove the soil For those laundries that may get lint ball and those with long fur tum it over before putting in Do not put those laundries polluted by chemicals into the washing machine directly Haier Do s and Don ts e The capacity of washing and spinning of the machine refer to the weight of the standard laundries under dry condition that can be washed or spinned in one time the largest capacity is only the loading capacity of the drum The thickness size type of the cloth will influ ence the actual washing capacity Itis suit able to put in reasonable amount of laundries and the laundries can be turned round in wash ing for one time washing Do not select Maximum water level for laundries less than 1 5kg so as to avoid splashing of water It is suggested not to use high sudsing detergent Usage of the detergent How to use the whitener Fill water to decided level Dilute the whitener with container Pour it slowly into the washing tub e Avoid using whitener on laun dries with color or pattern as they are prone to lose color The whitener shall not touch the laundries directly e Refer to the user s manual for the usage and quantity of the whitener e For powd
4. 2 Clean the lint Put it in water and clean while it is still wet See Figure 2 3 Install the lint filter After cleaning insert the bottom Figure 2 of the lint filter marked with down side into the overflow filter then push the upper part of the filter in marked with up side See Figure 3 Figure 3 Cleaning the overflow filter Too much lint on the overflow filter will influence the normal usage of the machine Please clean it every two months Take off the overflow filter Elastic fixing claw As indicated in the figure nip the elastic fixing claw and pull it to the direction of the arrow to take it off 12 Haler names of the parts Outer cover of the spin tub Water filling entrance Inner cover of the spin tub water filling translation a Spin timer Control panel Major frame Spin tub Overflow filter Water level adjusting lever Lint filter Installed by user Pulsator Sl N Cabinet Wash tub Power cord Drain hose Gy i ee Wash tub cover a Base frame Meaning and description of the symbols Contents marked with that symbol are related Warning sign to the safety of the product and the personal safety of the users Please operate in strict conformity to the contents otherwise it may cause damage of the machine or injure the personal safety of the user Forbidding sign Contents marked with that symbol are actions forbidden to perform Performing of those
5. Haler trouble shooting If the laundries fall to the outer side of the spin tub If the laundries fall to the outer side of the spin tub Please contact the after sales service department If there s breakdown please pull off the power plug before checking The following phenomena are not breakdowns sometimes Please confirm again before sending it to repair If there are real breakdowns please come to the special maintenance department or after sale service department of our company Do not repair it by yourself Phenomena The machine does not function The reason e Is there power failure e Is the power plug loose e Is the pulsator twisted by foreign materials How to settle e Use it when the power is on e Insert the power plug tightly Remove the foreign materials The draining does not function e Has the drain hose being laid down e s the drain hose blocked by foreign material Are there any laundries trapped at the outer side of the spin tub Put down the drain hose e Remove the foreign material e Please contact the after sales service department There s abnormal sound during washing Are there hair pin coins or meta items brought inside the tub le Remove the hair pin coins or metal items There s abnormal sound and violent vibration during spinning Is the machine slanting Is the gland pressed evenly Are there any laundries trapped at th
6. ated in Figure 2 Specification Disposal of the complete unit Rated voltage frenquency 220V 50Hz K e After washing dismount the water inlet l f a Wipe the complete unit with soft hose Water level Water quantity estimated L Maximum S8 Medium 49 Minimum 43 sloth twisted dry Do not store water iH the tub for long The Rated hi itv k 8 0 f l period Discharge the water immediately e Rated washing capacity kg Wipe with neutral detergent if too dirty Sher each using it di The Rated spinning capacity kg 6 0 Do not wash it directly by water fee power plug and hang up the Injection pressure MPa 0 02 0 2 s Hang up the drain hose J Wipe off the water drops on the surface and inside the tub with clean soft cloth Open the cover of the wash tub and the S inner outer cover of the spin tub for Specifications may be subject to change some time about one hour then close without prior notice them 13 Haier Maintenance e After using please clean the lint and eyewinker of the lint filter and overflow filter in time Otherwise it may influence your using the machine Please first pull off the power plug from the receptacle before cleaning Cleaning the lint filter The lint filter must be used during washing t must be cleaned in time after each using 1 Take off the lint filter Put hand at the indicated position Push down to take it off See Figure 1
7. e outer side of the spin tub Are the laundries in spin tub over loaded 14 e Pressed the gland evenly e Level the machine properly Remove the laundries e Remove alittle laundries USER WASHING MACHINE LOD f A Wg ii WI Mt i Tit il i i ii Ni WI WIV ll i SEMI AUTO WASHING MACHINE AWT 80LI Manual EE CONTENTS Packing list Specification Names of the parts Safety precautions Installation and adjustment Preparation before washing Do s and don ts Usage of the detergent Washing sequence Maintenance Trouble Shooting Haier Packing list Cleaning the overflow filter a Name Quantity 5 2 Take off the corrugation pipe Water level Dismantle the upper part of the adjusting lever User s manual One piece corrugation pipe inside the overflow filter as indicated in Corrugation Figure 1 Pipe gt Qs 7 Kj Water inlet hose Y lt 9 mna One piece Cleaning the overflow filter Clean the lint around the filter and flush with tap water Gland One piece Figure 1 Install the overflow filter 1 Install the corrugation pipe Semi Auto washing machine One set 2 Insert the mounting plate at aa ee the bottom of the filter into the valve cover 3 Hang up the hook at the left upper side 4 Push the upper part in as indic
8. er whitener please dissolve it before using How to use the washing powder eDirect dissolved in the machine 1 Fill small quantity of water 2 Add the powder Run for 30 seconds to dissolve it completely 3 Putin laundries Select suitable water level The instant dissolving of the washing powder 1 Prepare warm water of 30 C and a container 2 Add the powder while stirring to fully dissolve it The powder is more prone to pollute the laundries than the detergent Therefore please use it with proper quantity e Dosage of different washing powder is different Please refer to the instruction of the washing powder for the detail dosage
9. fixin 2 Adjust water level rod to a position as needed installation maroen me Pull the fixing hook outwards slightly Inlay the drain Figure 3 Figure 4 hose into the fixing hooks reliably along the groove at spin tub side and make it extend towards spin tub side 2 Fill the water and add the dissolved washing Then hang the drain hose intothe hanging holeat powder to make the water level reach the preset the spin tub side As perFigure 5 position Figure 2 a Figure 2 Run washing program for some time to stir and Sane Extend the drain hose from the back side dissolve the powder completely ae p ana Takeout the drainhose from thetwo fixing hooks DIN make it extend towards back side Extendthe drain Figure 5 Figure 6 3 Put in the laundries If the water quantity is g hose from the side of back hang the drain hose in insufficient please add water Figure 3 to the hanginghole at the both sides As per Figure6 Figure 1 4 Select the current Install the water inlet hose Select the water level Select the strength of the current according to es the laundries Figure 3 CEI N 5 Select the washing time Select the washing time according to the laundries Figure 4 Insert the water inlet hose into the water filling Water inlet hose entrance on the control panel directly pull it Figure 4 out to dismantle it Select water level according
10. imer to 2 3 minutes to do rinsing When the laundries quantity is few please use Standard current If you use Strong current it may splash 10 Haier Safety precautions Do not stretch hands into the working machine It is dangerous even if the rotation is slow Take special care of the children Do not decompose repair or alter the machine by yourself Do not put any hot or heavy items such as the kettle with hot water on the washing machine Do not wash laundries with volatile materials such as thinner petrol etc Handicapped or children without care shall not use the machine To protect your laundries and wash ing machine please take out all of the coins buttons sand hairpin and other foreign materials before washing Keep the machine away from direct sunlight and heat source like the heater Please check if the connection of the water inlet pipe is proper Itis suggested to use foamless washing powder Haler installation and adjustment Please install and adjust the machine according to the requirement of the manual It is very important to your security and correct operating the machine Install the lint filter After opening the package please take out the lint filter from the document bag install it to the overflow filter of the wash tub See to the figure Overflow filter Lint filter Usage of the drain hose The drainage shall be smo
11. oth with the drain hose 1 The height of the drain hose shall be less than 10cm or the drainage will not be smooth enough and cause incomplete drainage 2 Do not tramp or press the drain hose 3 If the drain hose is too long cut it at mid point To make smooth drainage cut the front end of the hose slantingly 5 Ce o 0 4 4 lf extra drain hose is needed please make separate purchase The inner diameter of the extra hose shall not less than 30mm and the length shall not exceed 1 5m If the extra hose is too long cut it either at point Aor B Haier Midway spinning 1 Put the laundries into the spin tub evenly and smoothly 2 Spin 1 Put the gland in properly Please put in the gland properly even if the laundries quantity is small Push Gland oh amp Proper The laundries Proper No gland are slanting 2 Close the inner and outer cover of the spin tub 3 Spin for 1 2 minutes Outer cover of the spin tub Inner cover of the spin tub 3 Run the foam removing spinning 1 Set the inlet selector handle on spin side and Water inlet fill water for about 1 min e In case water flows out from wash tub side due to too much inflow please turn down the water tap a bit 2 Close the spin tub outer cover and spin for about 1 2 min Ha ier Washing sequence Ha lef How to change the direction of the drain hoses
12. to the A Water level quantity of the laundries indicator e Set the water level adjusting lever to needed line Use the new water inlet hose provided Med with the machine to connect to the Med water faucet Old hose sets should Minimum Min not be reused STRONG 6 After washing the buzzer will ring Set Pia the WASH SELECTOR at DRAIN T Figure 5 CE Figure 5 Maximum Max ny Preparation before washing Preparation before washing 1 Connect the water inlet hose 2 Confirm that the washing machine is earthed reliably Then insert the power plug into the receptacle Do not connect the earth terminal to the gas pipe and tap water pipe 3 Put down the drain hose 4 Slanting or uneven ground may result in unstable working or abnormal noise Please make the machine stand horizontally Clear the pocket Take out the coins etc Zo sand hairpins close zippers The quantity of the laundries shall not be too buttons of the large Stretch laundries may and loosen the cause noise For laundries before the sake of putting them in discretion please the tub put the laundries with buttons into Tie the long strips fasten the buttons is running other laundries Check if the laundries are applicable for washing with machine Divide the laundries that are not colorfast from other laundries Put those laundries difficult to absorb water into
13. you open the outer cover of the spin tub Close it to resume the spinning For washing machine with ventilation Do not wash water proof laundries like openings inthe base that acarpet the raincoat bike covers etc to avoid oo a must not obstruct the openings abnormal vibrations To do spinning and draining and rinse Ventilation hole at the bottom of the X with water filling together please first washing machine do spinning for around 1 minute then do draining or rinse with water filling S SO Otherwise the spinning will stop owing to too much water stored in the spin tub Do not let the machine share one receptacle i u with other electric appliances If the power plug is damaged or the plugging into the receptacle is loose do not use the plug any more Rinse with water filling 1 Put the laundries Put the laundries into the wash tub Select suitable current according to the laundries 2 Adjust the water level Set the water level with water level adjusting lever according to the laundries quantity Then fill suitable water continuously 3 Rinse Adjust the wash timer to 5 7 minutes to do rinsing Rinse with stored water Repeat the midway spinning and rinsing with stored water for 2 3 times 1 Put the laundries into the wash tub Select suitable current according to the laundries 2 Fill water to preset water level 3 Rinse Adjust the wash t
Download Pdf Manuals
Related Search