Graco Inc. 309412F Paint Sprayer User Manual
Contents
1. Kit parts are marked with a symbol for example Sct e Acetal Seat Kit 249424 and Carbide Seat Kit 249456 can be used with both Model G15 guns and Model G40 guns e Acetal Seat Kit 249424 is intended for low pres sure usage Fan Valve Replacement 1 Relieve the pressure page 10 2 Unscrew the fan valve packing nut A from the back of the gun body 1 Slide the fan valve assembly 4 out of the gun body See FIG 35 3 Before reinstalling turn the pattern adjustment valve C of the replacement fan valve assembly 4 com pletely counterclockwise to prevent damage to the seat 5cT Install the replacement fan valve assem bly into the gun body 1 Screw the packing nut A into the gun body and torque to 90 in lb 10 5 Nem 20 Repair 1 4 gt C Le AXA ee ZX Torque to 90 in lb J a 10 5 Nem A TI6576A FIG 35 Complete Gun Packing Repair Disassembly Seat Repair K e See Repair Kits page 20 e Clean parts with a solvent that is compatible with the parts and the fluid being sprayed 1 Relieve the pressure page 10 Remove the fluid and air hoses from the gun 2 Remove the air cap retaining ring 6 air cap 21 and spray tip 33 See FIG 36 TI6568A FIG 36 3 Trigger the gun to pull the needle housing off the seat while you unscrew the diffuser 5 from the gun body 1 using the gun tool 30 311001C Repair 4 Inspect the o rings Be 5f and2. Push the u cup into the back of the gun until you feel a definite snap a J Lubricate lightly Lips face out of gun body a P TI6578A 42 Lubricate the front end of the air valve assembly 8 Gently slide the air valve assembly into the back of the gun passing through the u cup 7 as far as it vvill go Be careful not to damage the u cup See FIG 44 Slide the seat 10 onto the shaft 9 Be sure that the tapered end of the seat is toward the thicker end of the shaft Carefully insert the shaft 9 and seat 10 in the air valve 8 FIG Repair Install the two springs 15 and 19 Screw the spring cap 11 into the back of the gun body Torque to 175 185 in lb 20 21 Nem Lightly lubricate the needle assembly o rings and shaft where the packing slides Be sure that the o ring 2a is in place in the gun body 1 Insert the fluid needle assembly 2 into the front of the gun Use the nut driver 29 to screw the fluid needle assembly into the gun body 1 and torque to 50 60 in lb 6 7 Nem See FIG 43 1 gt d Da 29 da 2a aF N i TI6575A Install the trigger 3 pivot pin 13 and nut 14 Use low strength thread locker and be sure that the brass piece of the fluid needle assembly 2 is behind the trigger See Fic 44 Lubricate both sides of the pivot pin where the trigger contacts the pin and lubricate the boss on both sides of the gun where the trigger contacts the gun
3. bar Models ae 2 Clearing a clogged RAC tip 16 no 3 Troubleshooting 18 Fe 4 General Troubleshooting 18 ERO 6 REDA reiri Side oma oie nem pave boda see 20 ere 6 ltems Needed for Service 20 rye 6 Repair KIS EE a cube ote mena es 20 ee 7 Fan Valve Replacement 20 PERE 7 Complete Gun Packing Repair 20 A 8 Disassembly 20 Ne 8 Seat Repair 20 ee 8 Needle Repair 21 ee 8 Air Valve Repair 22 PT 8 Fluid Tube Replacement 22 ue 8 Reassembly 24 dere VO PANS 2acc twos eee eee eee ote ee tad 26 10 Spray Tip Selection Chart 30 senu NO AAM Fine Finish Spray Tips 30 10 GG4 Industrial Spray Tips 30 11 LTX RAC Spray Tips 31 ss ii FFT Fine Finish RAC Spray Tips 32 Less le WRX WideRAC Spray Tips 32 al ACCESSOIIS sauna eu bout a 33 dec MS Technical Data 2 02 edema cimueditage 34 14 DIMENSIONS ideat ics tades inner 35 14 Graco Standard Warranty 36 14 Graco Information 36 ite 16 on Loue G15 Medium Pressure 249596 Air Cap Air Assisted Spray Gun Plastic Seat SST Ball 249596 Air Cap G15 Medium Pressure Air Assisted Spray Gun Carbide Seat and Ball 100 0 7 7 0 4000 2 8 280 G40 Hig
4. 5g in place Needle Repair Carefully remove the o rings from the diffuser hous ing 5a and replace if necessary 1 Remove the diffuser see Seat Repair page 20 2 Remove the trigger pivot pin nut 14 pivot pin 13 and trigger 37 using the gun tool 30 and nut driver 29 See FIG 38 5 Remove the seat nut 5dTf seat 5cT and seat gas ket 5bT model G40 gun only using a 7 82 in hex wrench 6 Inspect the seat 5ct and seat gasket 5bT and replace if necessary 7 Reinstall the seat gasket 5bT model G40 gun only seat 5cT and seat nut 5df Torque to 45 50 in lb Be sure not to overtighten the nut K e When reinstalling the carbide seat 5cf the tapered end of the seat must point toward the gun tip e The acetal seat 5cT standard in model G15 guns 249233 can be reinstalled in either direction 14 TI6574A FIG 38 3 Remove the fluid needle assembly 2 from the front of the gun by using the nut driver tool 29 If the needle is bent or damaged or the packing is worn or leaking replace the entire needle assembly If replacement is necessary be sure to remove the o ring 2a as it may stick inside the gun body See FIG 39 w 4 re G40 only AA Al TI6572A FIG 37 OE TI6575A 311001C 21 Repair Air Valve Repair Fluid Tube Replacement 1 Unscrew the spring cap 11 from the back of the 1 Remove the air inlet fitting 17 using the gun tool gun body 1 u
5. body Torque the nut to 20 30 in lb 2 3 Nem Trigger the gun to pull the needle back while you screw the diffuser assembly 5 into the gun body 1 using the gun tool 30 Torque to 155 165 in lb 18 19 Nem When properly tightened the flange will bottom out on the gun Attach the retaining ring 6 air cap 21 and spray tip 33 311001C Repair 5bt G40 only Torque to 150 160 in lb 17 18 Nem 144 Ad 17A A Lubricate lightly AN Torque to 155 165 in lb 18 19 Nem A Torque to 20 80 in lb 2 3 Nem A Do not lubricate diffuser o rings 16 249238 amp A Brass part must be behind trigger Sr only 12 Lips face out of gun body a 249233 amp 249242 only A Torque to 50 60 in lb 6 7 Nem 16 Ads Torque to 125 135 in lb 14 15 Nem 249233 amp 249242 only as AN Torque to 45 50 in lb 5 6 Nem A 18 249233 amp 249242 only A 249233 torque only AA 249242 torque only Ad Use low strength thread locker Ad Torque to 175 185 in lb 20 21 Nem TI6579B FIG 44 311001C 25 Parts Parts Part No 249233 G15 Gun Part No 249242 G40 Gun Part No 249246 G40 Gun High Flow 5bt G40 only 21a G15 only 6 G40 only 12 249233 amp 249242 only o 30 249233 amp 249242 only 28 18 d fo 249233 amp 249242 only TI6579B 16 ou 249246 only 26 311001C Part No 249233 G15 Gun vv Plastic Seat Part No 287926 G15 Gun
6. ek ek L eh L L eh eh L eh eh eh eh eh L hL hL l ee eh eh eh h eh d A Replacement Danger and Warning labels tags and cards are available at no cost Included in Seal Repair Kit 249422 purchase sepa rately t Included in Acetal Seat Repair Kit 249424 purchase separately Included in Trigger Repair Kit 249585 purchase sep arately Included in Air Cap Seal Kit 253032 purchase sepa rately 311001C Part No 249242 G40 Gun w Standard Tip Parts Part No 249246 G40 Gun High Flow Ref No 1 1a 2 2a 3 4 5 5a 5bT 5cT 5dt 5e 5f Part No 249423 287885 249135 249133 249256 15F193 15F194 15F195 224453 114069 249136 249317 15F202 15F186 115141 119996 249180 117642 15F446 222385 172479 Description BODY gun S TOP trigger NEEDLE assy 3 32 ball carbide includes item 2a PACRING o ring PTFE TRIGGER gun VALVE fan assy DIFFUSER assy DIFFUSER housing GASRET seat nylon SEAT carbide NUT seat PACRING o ring seat PTFE PACRING o ring PTFE PACRING o ring PTFE TIP GUARD 249242 amp 249246 only PACRING o ring PTFE VVASHER PTFE PACRING u cup UHMVVPE VALVE air assy SHAFT fluid spring SEAT spring CAP spring FILTER tip pkg of 5 249242 only PIN pivot PIN pivot nut SPRING compression TUBE assy 249242 only TUBE assy 249246 only FITTING air inlet FITTING hos
7. flow stops This helps assure the spray is atomized and prevents fluid buildup on the air Cap Spray Pattern Adjustment 3 SKIN INJECTION HAZARD To reduce the risk of component rupture and serious injury including injection do not exceed the gun s maximum fluid working pressure or the maximum working pressure of the lowest rated component in the system 1 Do not turn on the gun air supply yet Set the fluid pressure at a low starting pressure If a fluid pres sure regulator is installed use it to make adjust ments If your system does not have a fluid regulator the fluid pressure is controlled by the air regulator sup plying the pump per the formula below Pump x Pump Air Regulator Setting Fluid Ratio Pressure 311001C Operation 2 Trigger the gun to check the atomization do not be concerned about the pattern shape yet 3 Slowly increase the fluid pressure just to the point where a further increase in fluid pressure does not significantly improve fluid atomization 4 Close off the pattern adjustment air by turning the knob clockwise in all the way See FIG 14 This sets the gun for its widest pattern a us a a CLOSE OPEN a TI6559A FIG 14 5 Set the atomizing air pressure at about 5 psi 0 35 bar 35 kPa when triggered Check the spray pat tern then slowly increase the air pressure until the tails are completely atomized and pulled
8. from serious injury including eye injury inhalation of toxic fumes burns and hearing loss This equipment includes but is not limited to e Protective eyewear e Clothing and respirator as recommended by the fluid and solvent manufacturer e Gloves e Hearing protection Installation Installation Typical Installation Grounding The typical installation shown in FIG 1 is only a guide for selecting and installing air assisted spray systems Con M tact your Graco distributor for assistance in designing a system to meet your needs Check your local electrical code and pump manual for detailed grounding instructions Use only electrically 7N a conductive fluid hoses Ground the spray gun through connection to a prop VENTILATE THE SPRAY BOOTH erly grounded fluid supply hose and pump To prevent hazardous concentrations of toxic and or flammable vapors spray only in a properly ventilated spray booth Do not operate the spray gun unless ventilation fans are operating Check and follow all of the National State and Local codes regarding air exhaust velocity requirements Check and follow all local safety and fire codes hy i j Mi r i F E D CP PS itn il DS a TI6554A F FIG 1 Typical Installation Model G15 Shown Key A Air Line Filter E Spray Gun B Air Shutoff Valve F Electrically Conductive Fluid Hose C Gun
9. use tips in the gray shaded area of the Spray chart with Model G15 guns 249233 Tip Selection Chart with Model G15 guns 249233 K e All tips in the Spray Tip Selection Chart below can be used with Model G40 guns 249242 Use tips in the gray shaded area of the chart with Model G40 guns only Failure to follow this warning can result in serious injury or amputation Fluid Output fl oz min lpm Maximum Pattern Width at 12 in 305 mm Orifice Size in at 600 psi at 1000 psi 2to4 4to6 6to8 8to 10 10to12 12 to 14 14to 16 16 to 18 18 to 20 ESA ESE EE EL far fer Ta a le ae oe a Tor ez mea 009 m m m m EL fe omes ooa wo fais fats fats sts CC Es TS SS ai rows eoon EL las jus oe rare EI 200m EI a r ar r iy LS ei at se a soa esua fate CC CC Gares souo asus CCC a a a ceea pa LOL ES ES LES DS SS LS CL SS ES A SP qr ES CL ES LS SL fee roast eran oea PS PS fast e RE ES ER DS Dc DS LS DS DS LS LS NS Tips are tested in vvater 3207 wr P r eee wr r Oe mr jsx mr ll Fluid output Q at other pressures P can be calculated by this formula Q 0 041 QT V P where QT fluid output fl oz min from the above table for the selected orifice size These tip sizes include a 150 mesh tip filter Do not use these tips with Model G15 guns 249233 GG4 tips only x Ho 30 311001C Spray Tip Selection Chart RAC
10. 249473 Alternative style connector for air inlet and hose 3 8 in to 1 4 npt f Push To Lock fitting 25 ft 7 62 m long 3 8 in 9 5 mm ID nylon tubing Air Hose 241811 100 psi 0 7 MPa 7 bar Maximum Working Pressure 1 4 18 npsm fbe 1 4 in 6 mm ID 25 ft 7 62 m long polyurethane tubing Air Line Quick Disconnect 208536 Air Line Quick Disconnect Coupling 169967 Air Line Quick Disconnect Pin Fluid Filter Kits 224453 100 mesh 005 gap spacing replacement fluid filters Quantity of 5 60 mesh 009 gap spacing replacement fluid filters for coarser particle filtering to replace standard 100 mesh filters Quan tity of 3 Fluid Hose 241812 3500 psi 24 MPa 242 bar Maximum Working Pressure 1 4 18 npsm fbe 3 16 in 5 mm ID 25 ft 7 62 m long nylon tubing with polyurethane cover Fluid Swivel Connector 115898 5800 psi 40 MPa 400 bar Maximum Working Pressure Connector to ease movement of the gun and fluid hose 1 4 18 npsm 17 4 PH SST wetted parts 238563 Gun Brush 101892 Use to clean the gun G15 Gun Flush Box Insert 15G093 Insert for use with Gun Flush Box 244105 and AA Series G15 Spray Guns G40 Gun Flush Box Insert 15G346 Insert for use with Gun Flush Box 244105 and AA Series G40 Spray Guns Gun Lubricant 111265 One 4 oz 113 g tube sanitary non silicone lubricant for fluid seals and wear areas High Pressure Fluid Ball Valve 238694 5000 psi 35 MPa 350 bar Maximum Working Press
11. 3a in solvent for extended periods of time or swelling may OCCUT Clearing a clogged RAC tip Release the trigger and engage the trigger lock XS A TI6568A M a FIG 25 lt 15 Dampen a soft cloth with solvent and wring out the 5 7 excess Point the gun down and wipe off the outside of the gun ENGAGED TI6581A FIG 28 TI6571A FIG 26 16 311001C Rotate the SwitchTip F gt TI7200A FIG 29 Disengage the trigger lock nd j Ed i a d f ot DISENGAGED TI6582A FIG 30 Trigger the gun into a pail to clear the clog SKIN INJECTION HAZARD Do not point gun at anyone or at any part of the body TI7202A FIG 31 311001C Daily Gun Care Flushing and Cleaning Engage the trigger lock ry ENGAGED TI6581A FIG 32 Return the SwitchTip to its original position o TI7201A FIG 33 Disengage the trigger lock and continue spraying do DISENGAGED TI6582A FIG 34 17 Troubleshooting Troubleshooting N bS Check all possible remedies in the trouble shooting charts before disassembling the gun e Some improper patterns are caused by the SKIN INJECTION HAZARD improper balance between air and fluid Follow Pressure Relief Procedure on page 10 Read warnings page 4 General Troubleshooting Problem Cause Somtion Fluid leakage from back of fluid Worn packings or needle shaft
12. Air Pressure Regulator G Gun Air Supply Hose D Air Line 6 311001C Installation Air Line Fluid Line 1 Install an air filter A on the gun air line to ensure a e Before connecting the fluid line blow it out with air dry clean air supply to the gun Dirt and moisture and flush it with solvent Use solvent which is com can ruin the appearance of your finished workpiece patible vvith the fluid to be sprayed See FIG 1 e f better control of fluid pressure is needed install a 2 Install an air pressure regulator C on the gun air fluid regulator on the fluid line to better control fluid line to control air pressure to the gun pressure to the gun 3 Install an air shutoff valve B on the gun air lineand 4 Use a fluid filter to remove coarse particles and sed on the pump air line to shut off air to the gun iment to avoid clogging the spray tip and causing 4 Use a 3 16 in 5 mm I D or larger air hose to mini finishing defects mize excessive pressure drop in the hose N Guns are equipped with a built in 100 mesh fluid fil the gun air inlet has a 1 4 18 npsm R1 4 19 com ter to provide final filtering just before spraying pound male thread that is compatible with NPSM and BSP female swivel connectors 2 Connect the fluid hose F to the gun fluid inlet See FIG 4 If desired install a fluid swivel connector 115898 at the gun inlet for best maneuverability See Accessories page 33 _ 5 Connect the
13. ING u cup UHMWPE VALVE air assy SHAFT fluid spring SEAT spring CAP spring PIN pivot PIN pivot nut SPRING compression TUBE assy FITTING air inlet SPRING compression SCREW cap socket hd 1 4 20 x 3 8 in 10 mm GASKET tube acetal TOOL installation seal TOOL nut driver TOOL gun CARD warning not shown TAG warning not shown SPRAY TIP customers choice see tip selection chart page 31 includes item 33a SEAT gasket HOUSING cylinder Qty ee ee ee eh ee ee ee ee ee ee ee ee a a a a ee a a a a oo b ee ee h ee eS A Replacement Danger and Warning labels tags and cards are available at no cost Parts included in Seal Repair Kit 249422 purchase separately t Parts included in Carbide Seat Repair Kit 249456 purchase separately Parts included in Trigger Repair Kit 249585 pur chase separately Parts included in RAC Conversion Kit 287917 pur chase separately 311001C Parts 29 Spray Tip Selection Chart Spray Tip Selection Chart Spray Tips for use with AA Series Air Cap AAM Fine Finish Spray Tips Recommended for high finish quality applications at low and medium pressures Order desired tip Part No AAMxxx from matrix below GG4 Industrial Spray Tips Recommended for high wear applications at high pressures Order desired tip Part No GG4xxx from matrix below S SKIN INJECTION HAZARD e Do not use tips in the gray shaded area of the Do not
14. Instructions Parts List GRACO AA Series Spray Gun 30010 For air assisted spraying and finishing of paints and coatings Ee Important Safety Instructions ee Read all warnings and instructions in this manual Save enia ST these instructions ee See page 2 for List of Models and Table of Contents NEE Fr SE P sous 7 Tete saci TE ORNE RACE P b TI6553A ee i gt TI6844A Model G40 w RAC tip N TI7204B RE 9 Model G40 EE bared Teen te NE a ote ae ir 7 PROVEN QUALITY LEADING TECHNOLOGY re Graco Inc P O Box 1441 Minneapolis MN 55440 1441 C Eu 2G sis Copyright 2005 Graco Inc is registered to I S EN ISO 9001 Contents Models Related Manuals Warnings Installation Typical Installation Grounding Air Line Fluid Line Setup Flush Before Using Equipment Select a Spray Tip and Air Cap Install a Spray Tip Position the Air Cap Air Cap Alignment Pin Operation Safety Pressure Relief Procedure Trigger Lock How the Air Assisted Spray Gun Operates Spray Pattern Adjustment HVLP Operation Fluid Application Daily Gun Care Flushing and Cleaning General System Maintenance Fluid Filter Maintenance Flushing and Cleaning Reverse A Clean RAC Tip Models Maximum Working Air Pressure psi MPa bar eee 100 0 7 7 0 1500 10 5 105 287926 ea 100 0 7 7 0 1500 10 5 105 Maximum Working Fluid Pressure psi MPa
15. Replace needle assembly 2 packing area Air leakage from gun Air valve not seating properly Clean or replace air valve 8 Fluid leakage from front of gun Needle ball worn or damaged Replace needle assembly 2 and seat 5c Worn seat assembly Replace the seat 5c and gasket 5b model G40 gun only The gasket must be replaced whenever the seat assembly is removed Fluid viscosity too low for proper Install acetal seat 5c seal with carbide seat Fluid in air passages a tip seal leaking el retaining ring 6 or replace spray tip sn dE around seat housing e the gasket 5b model G40 gun only The gasket must be replaced whenever the seat assembly is removed Fluid inlet fitting leaking Replace the fluid tube gasket 22 The gas ket must be replaced whenever the fluid tube connector is removed Slow fluid shut off Fluid buildup on fluid needle Remove and clean or replace the fluid needle components assembly 2 No fluid output when triggered Spray tip plugged Clean spray tip See page 14 Fluid filter or fluid hose plugged After tip removal see above very slowly loosen the hose end coupling at the gun and relieve pressure gradually Then loosen com pletely to clear the obstruction Clean or replace filter 12 18 311001C Troubleshooting Problem Cause Souten Fluttering or spitting spray Insufficient fluid supply Adjust fluid regulator or fill fluid supply tank Air in paint sup
16. SI Fan Valve Open 34 Fan Valve Closed 311001C Dimensions Dimensions Model G15 8 0 in 20 3 cm 5 0 in 12 7 cm 4 TI6583A 6 1 in 15 5 cm Model G40 TI6845A 6 9 in 17 5 cm 311001C 35 Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use With the exception of any special extended or limited warranty published by Graco Graco will for a period of twelve months from the date of sale repair or replace any part of the equipment determined by Graco to be defective This warranty applies only when the equipment is installed operated and maintained in accordance with Graco s written recommendations This warranty does not cover and Graco shall not be liable for general wear and tear or any malfunction damage or wear caused by faulty installation misapplication abrasion corrosion inadequate or improper maintenance negligence accident tampering or substitution of non Graco component parts Nor shall Graco be liable for malfunction damage or wear caused by the incompatibility of Graco equipment with structures accessories equipment or materials not supplied by Graco or the improper design manufacture installation operation or maintenance of structures accessories equipment or mat
17. SwitchTips for use with AA Series Air Cap N All tips in the Spray Tip Selection Charts below can N Tips are sometimes packaged with other promo be used with Model 249238 G40 guns equipped tional parts intended for the airless market Disre with RAC air cap 249478 gard extra parts LTX RAC Spray Tips Order desired tip Part No LTXxxx from matrix below Orifice Size in Bien pedal psi 2to4 4to6 6to8 8to 10 10to12 12to 14 14to 16 16 to 18 18 to 20 cwo oa 0 279 11660494 att jai att jsa o CEI 2806 as ais as se 0 015 0 881 80 8 09 215 as fas 515 Jes 1 17 mr Sur oo CO erae a a CE ES ES voos forom m o o f e DS DS ES es wr Sur CE CE CO D CO a z7 ca 0 027 0 686 0 029 0 737 wes RS E OEO ee ee ee eee ECA EC CEE ee ee ES cal es DE ES ES EE ES ES Tips are tested in vvater wr Nr Fluid output Q at other pressures P can be calculated by this formula Q 0 041 QT V P where QT fluid output fl oz min from the above table for the selected orifice size AOC Measured with NO airflow Air assist will tend to reduce pattern lengths by 1 in to 2 in 311001C 31 Spray Tip Selection Chart RAC SvvitchTips for use vvith AA Series Air Cap Continued AL e All tips in the Spray Tip Selection Charts below can be used with Model 249238 G40 guns equipped with RAC air cap 249478 FFT Fi
18. air hose G to the 1 4 npsm gun air inlet See FIG 2 pee pe d i ee Le P N M iY y R G i TI6556A FIG 4 b _ a d r Ds N k TI6846A FIG 2 3 Connect the other end of the fluid hose F to the 6 Connect the other end of the air hose G to the out pump fluid outlet let of the air shutoff valve See FIG 3 A TI4838A 311001C 7 Setup Flush Before Using Equipment 1 The equipment was tested with lightweight oil which is left in the fluid passages to protect parts To avoid contaminating your fluid with oil flush the equipment with a compatible solvent before using the equip ment See Flushing and Cleaning page 14 2 Relieve the pressure See Pressure Relief Proce dure page 10 Select a Spray Tip and Air Cap The fluid flow and pattern width depend on the size of the spray tip the fluid viscosity and the fluid pressure See Spray Tip Selection Chart page 30 Contact your Graco distributor for assistance in selecting an appropri ate spray tip for your application Install a Spray Tip Install a spray tip in the gun Ensure that the tip locating tab is positioned in the slot of the air cap See FIG 5 Tighten the air cap retaining ring 6 firmly by hand to ensure a good seal between the tip gasket and the dif fuser 5 Tip Locating Tab TI6847A FIG 5 Position the Air Cap The air cap and spray tip position determines the dir
19. ck equipment daily Repair or replace worn or damaged parts immediately with genuine Graco replacement parts only Do not alter or modify equipment For professional use only Use equipment only for its intended purpose Call your Graco distributor for information Route hoses and cables away from traffic areas sharp edges moving parts and hot surfaces Do not kink or overbend hoses or use hoses to pull equipment Comply with all applicable safety regulations Keep children and animals away from work area Do not operate the unit when fatigued or under the influence of drugs or alcohol 4 311001C 311001C Warnings WARNING PRESSURIZED ALUMINUM PARTS HAZARD Do not use 1 1 1 trichloroethane methylene chloride other halogenated hydrocarbon solvents or fluids containing such solvents in pressurized aluminum equipment Such use can cause serious chemical reaction and equipment rupture and result in death serious injury and property damage TOXIC FLUID OR FUMES HAZARD Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin inhaled or swallowed e Read MSDS s to know the specific hazards of the fluids you are using e Store hazardous fluid in approved containers and dispose of it according to applicable guidelines PERSONAL PROTECTIVE EQUIPMENT You must wear appropriate protective equipment when operating servicing or when in the operating area of the equipment to help protect you
20. co such as electric motors switches hose etc are subject to the warranty if any of their manufacturer Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties In no event will Graco be liable for indirect incidental special or consequential damages resulting from Graco supplying equipment hereunder or the furnishing performance or use of any products or other goods sold hereto whether due to a breach of contract breach of warranty the negligence of Graco or otherwise FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document as well as all documents notices and legal proceedings entered into given or instituted pursuant hereto or relating directly or indirectly hereto be drawn up in English Les parties reconnaissent avoir convenu que la r daction du pr sente document sera en Anglais ainsi que tous documents avis et proc dures judiciaires ex cut s donn s ou intent s la suite de ou en rapport directement ou indirectement avec les proc dures concern es Graco Information TO PLACE AN ORDER contact your Graco distributor or call to identify the nearest distributor Phone 612 623 6921 or Toll Free 1 800 328 0211 Fax 612 378 3505 All written and visual data contained in this document reflects the latest product information available at the time of publication Graco reserves the right to make changes at any time withou
21. commended as a flushing or cleaning solvent with SKIN INJECTION HAZARD this gun as it will damage aluminum and nylon compo Follow the Pressure Relief Procedure on page 10 nents before cleaning the gun CAUTION Solvent left in gun air passages could result in a poor quality paint finish Do not use any cleaning method which may allow solvent into the gun air passages Do not point the gun up while cleaning it Do not wipe the gun with a cloth soaked in solvent wring out the excess TI6563A TI4827A Do not immerse the gun in solvent Do not use metal tools to clean the air cap holes as this may scratch them scratches can distort the spray pat tern TI6564A penne 311001C 13 General System Maintenance 1 Relieve the pressure page 10 2 Clean the fluid and air line filters daily 3 Check for any fluid leakage from the gun and fluid hoses Tighten fittings or replace equipment as needed 4 Flush the gun before changing colors and whenever you are done operating the gun Fluid Filter Maintenance 1 Unscrew the fluid inlet fitting 18 2 Remove and inspect the inline fluid filter 12 Clean or replace the filter as necessary 18 TI6735A FIG 17 14 Daily Gun Care Flushing and Cleaning Flushing and Cleaning AN Ve FIRE AND EXPLOSION HAZARD Read Warnings page 4 Follow Grounding instructions page 6 N Flush befo
22. des replacement trigger stop and pin Ultimate Gun Cleaning Kit 15C161 Kit includes brushes and tools for gun maintenance Unclogging Needle Kit 249598 Kit includes picks for unclogging gun tip 33 Technical Data Category Maximum Working Fluid Pressure Maximum Working Air Pressure Maximum Gun Inlet Air Pressure for HVLP Operation Maximum Working Fluid Temperature Fluid Inlet Air Inlet LL ee LL LL Le GA WeIGK 2 SE net Sound Pressure at 20 psi 140 kPa 1 4 bar Sound Pressure at 100 psi 0 7 KPa 7 bar Sound Power at 20 psi 140 kPa 1 4 bar Sound Power at 100 psi 0 7 KPa 7 bar Wetted PATES reis das teues cetss eke ead oes Technical Data Data Model G15 1500 psi 10 MPa 105 ban Model G40 4000 psi 28 MPa 280 bar 100 psi 0 7 MPa 7 bar 14 psi 0 098 MPa 0 98 bar 110 F 43 C 1 4 18 npsm 1 4 18 npsm R1 4 19 compound male thread 16 oz 450 grams 66 9 dB A 80 0 dB A 76 8 dB A 89 9 dB A Stainless Steel Carbide Ultra High Molecular VVeight Polyethylene Acetal PTFE Nylon Flouroelastomer All readings were taken with the fan valve fully closed full fan size at 20 psi 140 kPa 1 4 bar and 100 psi 0 7 kPa 7 bar and at the assumed operator position Sound Power was tested to ISO 9614 2 Air Flow Standard AA Series Air Cap 12 10 Air Flow SCFM 20 30 40 50 Gun Inlet Pressure P
23. e 249242 only SPRING compression SCREW cap socket hd 1 4 20 x 3 8 in 10 mm 249242 only AIR CAP GASKET tube acetal TOOL installation seal TOOL nut driver TOOL gun CARD warning not shown TAG warning not shown SPRAY TIP customers choice Qty 1 1 1 h b b b b h ee ee ee ee a ee h b h h h ee ee ee ee a a a MA M b L s Ls hLs hLs hL A Replacement Danger and Warning labels tags and cards are available at no cost Included in Seal Repair Kit 249422 purchase sepa rately t Included in Carbide Seat Repair Kit 249456 pur chase separately Included in Trigger Repair Kit 249585 purchase sep arately Included in Air Cap Seal Kit 253032 purchase sepa rately 27 Parts Parts Part No 249238 G40 Gun w RAC Tip TSD 5ctx T17203B 28 311001C Part No 249238 G40 Gun w RAC Tip Ref No 4 1a 2 33a 35X Part No 249423 287885 15G713 249877 249478 15F193 15F194 15F195 114069 249317 15F202 115141 119996 117642 15F446 222385 172479 246453 15F442 Description BODY gun S TOP trigger NEEDLE assy 3 32 ball carbide includes item 2a PACRING o ring PTFE TRIGGER gun NUT air plug DIFFUSER assy RAC DIFFUSER housing GASRET seat nylon SEAT carbide NUT seat PACKING o ring seat PTFE PACKING o ring PTFE PACKING o ring PTFE TIP GUARD AIR CAP ASSY PACKING o ring PTFE PACK
24. e container ready to catch drainage Leave drain valve s open until you are ready to spray again 7 Engage the trigger lock See FIG 13 8 If you suspect the spray tip or hose is clogged or that pressure has not been fully relieved after follow ing the steps above VERY SLOWLY loosen the tip guard retaining ring or hose end coupling to relieve pressure gradually then loosen completely Clear hose or tip obstruction Trigger Lock Always engage the trigger lock when you stop spraying to prevent the gun from being triggered accidentally by hand or if dropped or bumped ENGAGED DISENGAGED TI6581A TI6582A FIG 13 311001C How the Air Assisted Spray Gun Operates The air assisted spray gun combines airless and air Spraying concepts The spray tip shapes the fluid into a fan pattern as does a conventional airless spray tip Air from the air cap further atomizes the fluid and completes the atomization of the paint tails into the pattern to pro duce a more uniform pattern The width of the pattern can be adjusted by the pattern adjustment valve The air assisted spray gun differs from an air spray gun in that increasing the pattern air reduces the pattern width To increase the pattern width use less pattern air or a larger size tip The spray gun has a built in lead and lag operation When triggered the gun begins emitting air before the fluid is discharged When the trigger is released the fluid stops before the air
25. ec tion of the spray pattern Rotate the air cap the spray tip rotates with it as needed to achieve the desired spray pattern direction See FIG 6 Setup TI6558A FIG 6 Air Cap Alignment Pin Model G15 guns 249233 use an air cap alignment pin to position the air cap The standard location of the air cap alignment pin is the horizontal air cap position If you would like to change the spray pattern direction use a needle nose pliers to unscrew the pin and relocate it to the desired position See FIG 7 When relocating the pin use low strength thread locker Torque to 1 5 2 5 in lb 0 2 0 3 Nem DO NOT OVERTIGHTEN The air cap alignment pin can be removed according to preference Air cap alignment pins do not come standard with model G40 guns 249242 TI6847A Horizontal Air Cap Position standard Vertical Air Cap Position FIG 7 311001C Setup Reverse A Clean RAC Tip Model 249238 guns use a Reverse A Clean RAC tip Insert the gasket seat To assemble the RAC tip insert the seat housing into the air cap assembly T17198A FIG 10 TI7196A FIG 8 Screw the RAC tip assembly onto the gun and tighten lt lt firmly by hand Insert the SwitchTip Fa T17199A TI7197A FIG 11 FIG 9 311001C 9 Operation Safety SKIN INJECTION HAZARD Remember this is not an air spray gun For your safety be sure to read and follow the Warnings o
26. erials not supplied by Graco This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect If the claimed defect is verified Graco will repair or replace free of charge any defective parts The equipment will be returned to the original purchaser transportation prepaid If inspection of the equipment does not disclose any defect in material or workmanship repairs will be made at a reasonable charge which charges may include the costs of parts labor and transportation THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE Graco s sole obligation and buyer s sole remedy for any breach of warranty shall be as set forth above The buyer agrees that no other remedy including but not limited to incidental or consequential damages for lost profits lost sales injury to person or property or any other incidental or consequential loss shall be available Any action for breach of warranty must be brought within two 2 years of the date of sale GRACO MAKES NO WARRANTY AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES EQUIPMENT MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO These items sold but not manufactured by Gra
27. h Pressure Air Assisted 249180 Spray Gun Carbide Seat and Ball Air Cap sal 100 0 7 7 0 4000 2 8 280 249238 m 100 0 7 7 0 4000 2 8 280 G40 High Pressure High Flow Air Assisted Spray Gun Carbide Seat and Ball G40 High Pressure Air Assisted Spray Gun Carbide Seat and Ball Reverse A Clean RAC Tip 249180 Air Cap 311001C Related Manuals Related Manuals This manual is available in the following languages Manual Language 311001C 3 Warnings Warnings The following are general warnings related to the setup use grounding maintenance and repair of this equipment Additional more specific warnings may be found throughout the body of this manual where applicable Symbols that appear in the body of the manual refer to these general warnings When these symbols appear throughout the man ual refer back to these pages for a description of the specific hazard WARNING FIRE AND EXPLOSION HAZARD Flammable fumes such as solvent and paint fumes in work area can ignite or explode To help prevent fire and explosion Use equipment only in well ventilated area Eliminate all ignition sources such as pilot lights cigarettes portable electric lamps and plastic drop cloths potential static arc Keep work area free of debris including solvent rags and gasoline Do not plug or unplug power cords or turn power or light switches on or off when flammable fumes are present Ground all equipmen
28. he gun tool 30 10 Dip the end of a soft bristle brush into a compatible solvent Do not continuously soak the brush s bris tles with solvent and do not use a wire brush TI4845A FIG 22 11 With the gun pointed down clean the front of the gun using the soft bristle brush and solvent TI6569A FIG 23 12 Scrub the air cap retaining ring 6 air cap 21 dif fuser 5 and spray tip 33 with the soft bristle brush To clean out air cap holes use a soft tool such as a toothpick to avoid damaging critical sur faces Blow air through the spray tip to ensure the orifice is clean Clean the air cap and spray tip daily minimum Some applications require more frequent cleaning 15 Daily Gun Care Flushing and Cleaning 16 After cleaning the gun lubricate the follovving parts with lubricant 111265 weekly e Trigger pivot pin A e Boss on both sides of the gun where the trigger contacts the gun body B e Fluid needle shaft behind trigger C _ TI6570A FIG 24 13 If the diffuser was removed trigger the gun while you reinstall the diffuser 5 with the gun tool 30 Tighten the diffuser securely to obtain a good seal Torque to 155 165 in lb 18 19 Nem When properly tightened the flange will bottom out on the gun FIG 27 TI6553A 14 Install the air cap retaining ring 6 air cap 21 and spray tip 33 Reverse A Clean RAC Tip N Do not soak the RAC tip seat gasket 3
29. into the spray pattern See FIG 15 Do not exceed 100 psi 0 7 MPa 7 bar air pressure to the gun For a narrower pattern turn the pattern adjustment valve knob counterclockwise out See FIG 14 If the pattern is still not narrow enough increase the air pressure to the gun slightly or use a different size tip Not available for RAC tip guns TIO792A correct amount of air no air too little air FIG 15 11 HVLP Operation N For HVLP operation the atomization air must not exceed 10 psi Use HVLP Verification Rit 249140 to verify air psi N There is no fan adjustment when using RAC tips and caps Fluid Application Always hold the gun at a right angle from the surface Do not make an arc with the gun as it causes an uneven coat of fluid See FIG 16 f TI6561A INCORRECT a FIG 16 12 Operation To achieve the best results when applying fluid keep the gun perpendicular to the surface and main tain a consistent distance of approximately 8 to 12 in 200 to 300 mm from the object being sprayed To obtain an even finish use smooth even strokes across the object being sprayed with 50 overlap Paint using parallel strokes This spray gun applies all coatings evenly without cross coating hs 4 TI6562A CORRECT 311001C Daily Gun Care Flushing and Cleaning Daily Gun Care Flushing and Cleaning N Methlyene chloride with formic or propionic acid is not re
30. n pages 4 and 5 and throughout the text of this instruc tion manual Keep the wallet sized warning card 222385 pro vided with the gun with the operator of this equip ment at all times The card contains important treatment information should an injection injury occur Additional cards are available at no charge from Graco Pressure Relief Procedure SKIN INJECTION HAZARD The system pressure must be manually relieved to prevent the system from starting or spraying acciden tally Fluid under high pressure can be injected through the skin and cause serious injury To reduce the risk of an injury from injection splashing fluid or moving parts follow the Pressure Relief Procedure whenever you e are instructed to relieve the pressure e stop spraying e check or service any of the system equipment e Or install or clean the spray tip Follow Pressure Relief Procedure on page 10 when you stop spraying and before cleaning checking ser vicing or transporting equipment Read Warnings page 4 1 Engage the trigger lock See FIG 13 2 Shut off the pump See your pump manual 3 Shut off the gun air supply 4 Disengage the trigger lock See FIG 13 10 Operation 5 Hold a metal part of the gun firmly to a grounded metal pail Trigger the gun to relieve pressure See FIG 12 TI6555A FIG 12 6 Open all fluid drain valves in the system having a wast
31. ne Finish RAC Spray Tips Order desired tip Part No FFTxxx from matrix below Fluid Fluid Output fl oz min Ipm fl oz min Ipm 4 Maximum Pattern Width at 12 in 305 mm Orifice Size in at pre aa psi 4 to 6 6to8 8to 10 10to 12 12to 14 area 0 MPa 140 bar 150 200 250 300 350 c esea ES ES PS ES NS CES SCC IS EE FES CTE EC IN VVRX VVideRAC Spray Tips Order desired tip Part No WRXxxx from matrix below Maximum Fluid Output Pattern Width at fl oz min lpm 12 in 305 mm Orifice Size in at 2000 psi 24 in eee 1 14 0 MPa 140 bar 610 0 021 0 533 0 533 60 5 1 79 605 179 iat 0 023 0 584 72 7 2 15 122300 0 025 0 635 85 9 2 54 mr mr 0 027 0 686 100 0 2 96 1227 0 029 0 737 115 6 3 42 12290 0 031 0 787 131 8 3 90 CCS 0 033 0 838 149 4 4 42 11233 0 035 0 889 168 3 4 98 11235 0 2 0 037 0 940 187 9 5 56 1237 0 039 0 991 208 9 6 18 123900 Tips are tested in water r Fluid output Q at other pressures P can be calculated by this formula Q 0 041 QT V P where QT fluid output fl oz min from the above table for the selected orifice size Sd Measured with NO airflow Air assist will tend to reduce pattern lengths by 1 in to 2 in 32 311001C Accessories Use Only Genuine Graco Parts and Accessories Air Fitting and Tubing Kit
32. ply line Check tighten pump siphon hose connec tions bleed air from paint line Attempting to feather partially Cannot feather with an AA gun Feather will trigger the gun cause drastic reduction of pressure at the tip resulting in poor atomization and or spitting Striping spray Spray tip partially plugged Clean or replace spray tip See page 14 i Irregular pattern Fluid build up on spray tip or Clean or replace spray tip See page 14 spray tip partially plugged On defective side of pattern air Clean air horn holes with solvent and soft horn holes are partially or totally brush See page 14 plugged Pattern pushed to one side Air horn holes partially or totally Clean air horn holes with solvent and soft same side of air cap gets dirty plugged brush or toothpick See page 14 311001C 19 Repair Items Needed for Service Seal Installation Tool 28 provided Nut Driver Tool 29 provided Gun Tool 30 provided O ring Pick 7 32 in Hex Wrench 3 16 in Hex Wrench Compatible Solvent Lubricant part number 111265 Repair Rits K e Seal Repair Kit 249422 is available For best results use all the new parts in the kit Kit parts are marked with an asterisk for example 7 e Acetal Seat Repair Kit 249424 standard for Model G15 guns and Carbide Seat Kit 249456 standard for Model G40 guns are available For best results use all new parts in the kit
33. re changing colors before fluid can dry in the equipment at the end of the day before storing and before repairing equipment e Flush at the lowest pressure possible Check connectors for leaks and tighten as necessary e Flush with a fluid that is compatible with the fluid being dispensed and the equipment wetted parts 1 Relieve the pressure page 10 2 Remove the air cap retaining ring 6 air cap 21 and spray tip 33 3 Disconnect the fluid supply hose F and air supply hose G from the gun T i a j 5 E S N 4 E X 4 ra TI6566A T16567A F A A FIG 18 311001C 4 Connect the solvent supply hose T to the gun SS TI6557A 5 Increase the pressure slovviy Point the gun down into a grounded metal container and flush the gun with solvent until all traces of fluid are removed from the gun passages Le FIG 19 TI6729A FIG 20 6 Turn off the solvent supply 7 Relieve the pressure 8 Disconnect the solvent supply hose T from the gun _ LE SES ja j 1 N A y T I TI6566A FIG 21 311001C Daily Gun Care Flushing and Cleaning CAUTION Trigger the gun whenever you tighten or remove the diffuser 5 This keeps the needle ball away from the seating surface and prevents the seat from being damaged 9 lfitis necessary to remove the diffuser 5 to clean trigger the gun while you remove the diffuser with t
34. sing the gun tool 30 Remove the 30 and remove the screw 20 using a 3 16 in hex two springs 15 and 19 the shaft 9 and seat 10 wrench 2 Push the air valve assembly 8 out the back of the 2 Unscrew the fluid inlet fitting 18 Remove and gun See FIG 40 clean or replace the inline fluid filter 12 3 Inspect the u cup 7 in the gun body 1 If the 3 Unscrew the fluid tube connector C from the gun s u cup is worn or leaking carefully remove the u cup fluid inlet Carefully remove the gasket 22 from the front of the gun body using a pick 15 1 8 gt pe 9 gt SP a eo le it AA 19 j FE A y P 9 j TI6573A TI6577A FIG 40 FIG 41 22 311001C Repair 311001C 23 Reassembly AL e See Repair Kits page 20 FIG 24 Install the tube gasket 22 in the gun Handtighten the fluid tube connector C into the gun s fluid inlet Handtighten the air inlet fitting 17 and screw 20 Torque the fluid tube connector to 150 160 in ib 17 18 Nem Torque the air inlet fitting to 175 185 in lb 20 21 Nem Torque the fluid tube bracket screw to 50 60 in lb 6 7 Nem See FIG 44 Install the inline fluid filter 12 into the base of the fluid tube Screw the fluid inlet fitting 18 into the base of the tube Torque to 175 185 in lb 20 21 Nem See FIG 44 Place the new u cup 7 on the seal installation tool 28 with the u cup lips facing the tool as shown in FIG 42
35. t in vvorR area See Grounding instructions Use only grounded hoses Hold gun firmly to side of grounded pail when triggering into pail If there is static sparking or you feel a shock stop operation immediately Do not use equipment until you identify and correct the problem Keep a fire extinguisher in the work area SKIN INJECTION HAZARD High pressure fluid from gun hose leaks or ruptured components will pierce skin This may look like just a cut but it is a serious injury that can result in amputation Get immediate surgical treatment e Do not point gun at anyone or at any part of the body Do not put your hand over the spray tip Do not stop or deflect leaks with your hand body glove or rag Do not spray without tip guard and trigger guard installed Engage trigger lock when not spraying Follow Pressure Relief Procedure in this manual when you stop spraying and before cleaning checking or servicing equipment EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury e Do not exceed the maximum working pressure or temperature rating of the lowest rated system component See Technical Data in all equipment manuals Read fluid and solvent manufacturer s warnings For complete information about your material request MSDS from distributor or retailer Use fluids and solvents that are compatible with equipment wetted parts See Technical Data in all equipment manuals Read fluid and solvent manufacturer s warnings Che
36. t notice MM 311001 Graco Headquarters Minneapolis International Offices Belgium China Japan Korea GRACO INC P O BOX 1441 MINNEAPOLIS MN 55440 1441 www graco com Printed in USA 311001C 12 2005
37. ure 3 8 npt mbe SST wetted parts PEEK seats PTFE seals Compatible with acid catalyzed materials Can be used as fluid drain valve 311001C Accessories HVLP Verification Kit 249140 Use to check air cap air pressure at various air supply air pressures Do not use for actual spraying N To be HVLP compliant the atomizing air pressure must not exceed 10 psi 70 kPa 0 7 bar RAC Gasket 246453 Pack of five standard replacement RAC gaskets item 33a Acetal RAC Gasket 248936 Pack of five plastic acetal replacement RAC gaskets item 33a G40 RAC Conversion Kit 287917 Kit includes parts to convert a standard G40 gun 249242 to a RAC gun LTX spray tip not included Air Cap Seal Kit 253032 Pack of five seals and five o rings for the air cap assy Seal Repair Kit 249422 Kit includes replacement o rings gasket u cup air valve assembly and seal installation tool Acetal Seat Repair Kit 249424 Kit includes replacement acetal seat pack of ten and seat nut for Model G15 gun Carbide Seat Repair Kit 249456 Kit includes replacement carbide seat seat gasket and seat nut for Model G40 gun Kit can also be used with Model G15 guns but is not standard Tip Filter Kit 241804 Replacement filters for spray tip orifice sizes 0 007 0 009 and 0 011 Quantity of 10 Trigger Repair Kit 249585 Kit includes replacement trigger pivot pins qty of 5 and pivot pin nuts qty of 5 Trigger Stop Kit 249423 Kit inclu
38. w Carbide Seat Ref No 1 1a 5cT 5dt 5f 5g 6a 6b 8 10 11 12 134 14 16 17 19 Part No 249423 249218 287885 249135 249132 249133 15F192 15F193 15F194 15F195 224453 114069 249136 15F202 15F186 119767 115141 119996 249596 15G618 117642 15F446 222385 172479 Description BODY gun S TOP trigger NEEDLE assy 3 32 ball sst includes item 2a 249233 only NEEDLE assy 3 32 ball carbide includes item 2a 287926 only PACRING o ring PTFE TRIGGER gun VALVE fan assy DIFFUSER assy 249233 only DIFFUSER assy 287926 only DIFFUSER housing GASRET seat nylon 287926 only SEAT acetal 249233 only SEAT carbide 287926 only NUT seat PACKING o ring seat PTFE PACKING o ring PTFE PACKING o ring PTFE RING retaining PACKING o ring PTFE WASHER PTFE PACKING u cup UHMWPE VALVE air assy SHAFT fluid spring SEAT spring CAP spring FILTER tip pkg of 5 PIN pivot PIN pivot nut SPRING compression TUBE assy FITTING air inlet FITTING hose SPRING compression 249233 only SPRING compression 287926 only SCREW cap socket hd 1 4 20 x 3 8 in 10 mm AIR CAP includes item 21a PIN air cap indexing GASKET tube acetal TOOL installation seal TOOL nut driver TOOL gun CARD warning not shown TAG warning not shown SPRAY TIP customers choice Qty 1 1 1 h h b h eh eh eh eh eh eh
Download Pdf Manuals
Related Search