Home

GE Monogram Drawer Freezer Refrigerator Refrigerator User Manual

1. e Turn on the water at the shut off valve to check for leaks STEP 12 CONNECT POWER e Connect refrigerator power cord plug to a properly grounded receptacle e Check to make sure power to refrigerator is on by opening refrigerator door to see if interior lights are on STEP 13 MOVE REFRIGERATOR INTO POSITION e Remove outside protective wrapping e Move the refrigerator into final installation position e Remove door spacer if not removed earlier and all inside packaging Installation Instructions STEP 14 LEVEL THE REFRIGERATOR Adjust the Rollers The refrigerator can be leveled by adjusting the rollers front and rear Rollers have three purposes e The rollers adjust so that the door closes easily when opened about halfway Raise the front about 5 8 16 mm from the floor e Rollers adjust to allow the refrigerator to be firmly positioned on the floor and to prevent rocking when the doors are opened and closed e The rollers allow you to move the refrigerator from the wall for cleaning To Adjust the Rollers e Use a 3 8 hex socket or wrench to turn the adjustment screws Turn the screws clockwise to raise the refrigerator turn counterclockwise to lower it e Use a 5 16 hex socket to turn the screws for the rear rollers Turn the screws clockwise to raise the refrigerator counterclockwise to lower it Rear Roller Adjustment Screw Front Roller Adjustment Leveli
2. 1 Measure Cabinet Opening Step 2 Install Anti Tip Bracket Step 3 Install the Refrigerator Step 4 Remove the Freezer Drawers Step 5 Remove the Fresh Food Doors Step 6 Remove the Toekick Step 7 Move the Refrigerator Planning Information PRODUCT DIMENSIONS AND CLEARANCES 35 7 8 27 1 2 Case Width 7 Depth Depth Including Handles ae 29 1 2 Tubular Handles 30 1 4 Professional Handles These Monogram free standing refrigerators require the Installation in a corner following clearances for proper air circulation plumbing e Allow 4 clearance on each side to an adjacent wall for a and electrical connections 90 opening and access to drawers Air Circulation Clearances e 1 8 on each side e 1 2 at the back side 150 Door Swing e Allow 15 clearance to wall on each side for removal of drawers THE INSTALLATION SPACE The opening width must be at least 36 Water And Electrical Locations The opening must be prepared with the electrical and water supply located as shown l 36 min Additional Specifications a New e A 115 volt 60Hz 15 or 20 amp power supply is required An individual properly grounded branch circuit or circuit breaker is recommended Install a properly grounded 3 prong electrical receptacle recessed into the back wall Electrical NOTE GFI ground fault interrupter is not recommended Area e The cold water line can enter the opening through th
3. Installation Instructions Stainless Steel Free Standing Drawer Freezer Refrigerator 31 46515 Monogr 225D1974P005 monog ram com Safety Information BEFORE YOU BEGIN Read these instructions completely and carefully IM PO RTANT Save these instructions for local inspector s use IM PO RTANT Observe all governing codes and ordinances e Note to Installer Be sure to leave these instructions with the Consumer e Note to Consumer Keep these instructions with your Owner s Manual for future reference A WARNING This appliance must be properly grounded See Grounding the Refrigerator page 4 A AVERTISSEMENT Cet appareil doit tre correctement mis la terre Consulter Mise la terre du r frig rateur page 4 If you received a damaged refrigerator you should immediately contact your dealer or builder Skill Level installation of this refrigerator requires basic mechanical carpentry and plumbing skills Proper installation is the responsibility of the installer Product failure due to improper installation is not covered under the GE Appliance Warranty See the Owner s Manual for warranty information CONTENTS Planning Information A CAUTION Due to the weight and size of this refrigerator and to reduce the risk of personal injury or damage to the product TWO PEOPLE ARE REQUIRED FOR PROPER INSTALLATION A PRUDENCE A cause du poids et de la tail
4. Minimum Acceptable Installation 1 as illustrated in Fig 2 STEP 2C POSITION THE REFRIGERATOR TO ENGAGE THE ANTI TIP FLOOR AND BASE BRACKETS Before pushing the refrigerator into the opening plug the power cord into the receptacle and connect waterline if equipped Check for leaks Locate the refrigerator s RH side and move back approximately in line with the RH side of the cabinet opening W This should position the anti tip floor bracket to engage the anti tip base bracket on the refrigerator Gently roll the refrigerator back into the cabinet opening until it comes to a complete stop Check to see if the refrigerator front lines up with the cabinet front face If not carefully rock the refrigerator forward and backward until engagement occurs and you notice that the refrigerator is fully pushed up against the rear wall OPTIONAL Adjust the rear and front wheel height settings to fully engage the rear anti tip brackets while also aligning the refrigerator front with the cabinet front face NOTE If you pull the refrigerator out and away from the wall for any reason make sure the anti tip floor bracket is engaged when the refrigerator is pushed back against the wall rear wall Installation Instructions STEP 3 INSTALL THE REFRIGERATOR BEFORE MOVING REFRIGERATOR INDOORS M PO RTANT Doors and passageways into the installation location require a 31 min opening If t
5. all after installation Bend the tubing into 3 coils of about 10 NOTE The only GE approved plastic tubing is supplied in GE SmartConnect Refrigerator Tubing kits Do not use any other plastic water supply line because the line is under pressure at all times Certain types of plastic will crack or rupture with age and cause water damage to your home GE SmartConnect Refrigerator Tubing Kits are available in the following lengths 2 0 6 m WxX08X10002 6 1 8 m WX08X10006 15 4 6 m WxX08X10015 25 7 6 m WX08X10025 Shut off the main water supply Turn on the nearest faucet long enough to clear the line of water e Install a shut off valve between the icemaker water valve and cold water pipe in a basement or cabinet The shut off valve should be located where it will be easily accessible e Turn on the main water supply and flush debris Run about a quart of water through the tubing into a bucket Shut off water supply at the shut off valve NOTE Saddle type shut off valves are included in many water supply kits but are not recommended for this application NOTE Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to Saddle valves are illegal and use is not permitted in Massachusetts Consult with your licensed plumber Installation Instructions STEP 10A WATER LINE INSTALLATION WITH A REVERSE OSMOSIS SYSTEM Skip this step when not using RO System If the water supply
6. and out of the slide REMOVE THE LOWER BASKET A Open the bottom freezer drawer until it stops B Lift the rear of the basket up so the two rear alignment tabs are pulled out of the slide bracket C Rotate the basket up and out of the drawer REMOVE THE DRAWER FRONT FROM THE SLIDES A Remove the 10 hex head screws from the door and remove the door B Set the drawer front on a non scratching surface C Push the rail assemblies back into the cabinet STEP 5 REMOVE THE FRESH FOOD DOORS The top cap must be removed to access hinges It is best to remove one door at a time A Remove 2 screws on top and 2 screws at the back of the top cap Lift off top cap B Remove 2 screws holding top hinge to the case Carefully lift off left and right side doors Top Cap Screws _ Installation Instructions STEP 6 REMOVE THE TOEKICK If after removing the freezer drawers and refrigerator door the refrigerator will still not fit through a doorway the toekick can be removed e Remove the toekick by removing the 2 Phillips head screws i STEP 7 MOVE THE REFRIGERATOR e Place a piece of the carton or soft cloth against the side panel of the refrigerator to pad and protect the stainless steel finish e Place the refrigerator on the handtruck with a side against the truck only e Move the refri
7. e 1 Wall Plate Stud Minimum Acceptable 3 Concrete Floor STEP 2B INSTALL ANTI TIP BRACKET WOOD Wall and Floor Construction A Drill the appropriate number of 1 8 pilot holes in the center of each floor bracket hole being used a nail or awl may be used if a drill is not available AND remove the locator template from the floor Mount the anti tip floor bracket by fastening the 2 or preferably 4 10 16 hex head screws tightly into place as illustrated in Figure 3 Figure 3 Attachment to Wall and Floor Rear RH Corner of the Refrigerator Floor Bracket 2 Screws Must N Enter Wood or Metal Stud STEP 2B INSTALL ANTI TIP BRACKET CONT CONCRETE Wall and Floor Construction A Anchors required not provided 4 each 1 4 x 1 1 2 lag bolts 4 each 1 2 O D sleeve anchors Drill the recommended size holes for the anchors into the concrete at the center of the holes marked in Step 2 Install the sleeve anchors into the drilled holes Place the anti tip floor bracket as indicated in Step 2 Remove the locator template from the floor D Install the lag bolts through the anti tip floor bracket and tighten appropriately WOOD Wall and TILE Floor Construction A For this special case locate the 2 wall holes identified in Fig 1 Drill an angled 1 8 pilot hole approx as shown in Fig 3 in the center of each hole B Mount the anti tip floor bracket using the
8. e floor or through an adjacent cabinet as close to the back wall as possible The water line should be GE SmartConnect Refrigerator Tubing or 1 4 O D copper tubing between the cold water line and water connection location at the rear of the refrigerator Installation of an easily accessible shut off valve in the water line is recommended Water Supply Installation Instructions TOOLS REQUIRED e Adjustable wrench e 3 8 and 5 15 socket ratchet driver e Phillips head screwdriver e 3 32 1 8 1 4 Allen wrenches e 1 8 Drill bit and electric or hand drill e Tape measure e Pencil e Wire cutters e 1 4 Nut driver e Level MATERIALS REQUIRED e 1 4 O D compression nut and 2 ferrules sleeves OR GE SmartConnect Refrigerator Tubing Kits GROUNDING THE REFRIGERATOR IMPORTANT Please read carefully FOR PERSONAL SAFETY THIS APPLIANCE MUST BE PROPERLY GROUNDED The power cord of this appliance is equipped with a 3 prong grounding plug which mates with a standard 3 prong grounding wall receptacle to minimize the possibility of electric shock hazard from this appliance Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded Where a standard 2 prong wall outlet is encountered it is your personal responsibility and obligation to have it replaced with a properly grounded 3 prong wall outlet FLOORING For proper installation
9. e floor up against the rear wall within W and in line with the desired location of the RH side of the refrigerator see Figure 1 Figure 1 Installation Overview Floor Concrete 2 Wall Holes 2 Holes Floor Wood Floor Bracket A 2 Holes oo x ______ RH Holes f Corner of Base Locator Cabinet Wall Bracket on Template the Refrigerator lt RH Side of Sheet Refrigerator B Place the anti tip floor bracket onto the locator template with its RH floor holes lined up with the floor holes indicated on the template sheet approxi mately 7 1 4 from the edge of the sheet or the RH side of the refrigerator C Hold down in position and use the anti tip floor bracket as a template for marking the holes based upon your configuration and type of construction as shown in Step 3 Mark the hole locations with a pencil nail or awl NOTE It is REQUIRED to use at least 2 screws to mount the floor bracket one on each side of the anti tip floor bracket Both must be into either the wall or the floor Figure 2 indicates all the acceptable mounting configurations for screws Identify the screw holes on the anti tip floor bracket for your configuration Installation Instructions STEP 2A LOCATE ANTI TIP FLOOR BRACKET CONT Figure 2 Acceptable Screw Placement Locations Preferred Installation Preferred Installation Wood Concrete Minimum Acceptable 2 Wood Floor Minimum Acceptabl
10. gerator indoors Place refrigerator close to the installation location STEP 8 REPLACE THE FREEZER DRAWERS Two people may be required to complete this procedure TOP DRAWER ATTACH AND SECURE THE DRAWER FRONT TO THE SLIDES A Pull out the rail assemblies to the full length on each side of the cabinet STEP 8 REPLACE THE FREEZER DRAWERS CONT B Drive the bottom outside screw into the door on each side until it is all the way in C Drive the remaining 3 screws on each side all the way into place there are a total of 8 hex head screws y Screws REPLACE THE FREEZER BASKET Replace the top drawer freezer basket Installation Instructions STEP 8 REPLACE THE FREEZER DRAWERS CONT BOTTOM DRAWER ATTACH AND SECURE THE DRAWER FRONT TO THE SLIDES A Pull out the rail assemblies to the full length on each side of the cabinet B Drive the top screw into the door on each side until it is 1 2 way in C Hang the drawer front onto the open slots on the slides 10 STEP 8 REPLACE THE FREEZER DRAWERS CONT D Drive the screws fully There are 10 screws 5 on each side Step D2 el z Drive screws _ Q in these holes AZ Step D1 Line up screw hole in freezer drawer and drive fully REPLACE THE FREEZER BASKET e Replace the bottom drawer freezer basket by lowering it into the frame Installation Instructi
11. he opening is less than 31 the top cap doors and drawers must be removed See steps 4 6 NOTE Skip steps 4 6 if door removal is not required Go to page 9 Move The Refrigerator NOTE To prevent damage leave inside packaging door spacer and outside protective wrap in place until the unit is moved to the installation location STEP 4 REMOVE THE FREEZER DRAWERS The freezer drawers can be removed if needed to fit through tight areas Read these instructions completely and carefully TOP DRAWER REMOVE THE BASKET A Open the freezer drawer until it stops B Cut the 2 wire ties off of the basket with wire cutters C Lift the front end of the basket so that the front two alignment tabs come out of the slide bracket first D Then rotate the front edge of the drawer up while lifting the remaining two rear alignment tabs out of the slide bracket Pull the basket up and out of the drawer REMOVE THE DRAWER FROT FROM THE SLIDES A Remove the 8 hex head screws from the door and remove the door B Set the drawer front on a non scratching surface C Push the rail assemblies back into the cabinet Installation Instructions STEP 4 REMOVE THE FREEZER DRAWERS CONT BOTTOM DRAWER REMOVE THE UPPER BASKET A Open the bottom freezer drawer until it stops B Pull the basket out to the stop location C Lift the basket up at the front to release it from the slides D Lift the back up
12. le de ce r frig rateur et pour r duire le risque de blessure et de dommages IL FAUT DEUX PERSONNES POUR FAIRE L INSTALLATION CORRECTEMENT A WARNING e Use this appliance only for its intended purpose e Immediately repair or replace electric service cords that become frayed or damaged e Unplug the refrigerator before cleaning or making repairs e Repairs should be made by a qualified service technician A AVERTISSEMENT e ne faut utiliser cet appareil que pour l utilisation appropri e e R parer ou remplacer imm diatement tout cordon lectrique effiloch ou endommag e faut d brancher le r frig rateur avant le nettoyage ou toute intervention e Les r parations doivent tre faites par un technicien qualifi For Monogram local service in your area call 1 800 444 1845 For Monogram service in Canada call 1 800 561 3344 For Monogram Parts and Accessories call 1 800 626 2002 www monogram com Product Dimensions and Clearances The Installation Space Step 8 Replace the Freezer Drawers Step 9 Replace Fresh Food Doors Step 10 Install Water Line Step 10A RO Water Line Step 11 Connect Water Supply Step 12 Connect Power Step 13 Move Refrigerator Into Position Step 14 Level Refrigerator Step 15 Level Doors Step 16 Install Toekick Step 17 Start Icemaker Step 18 Temperature Controls Installation Instructions Tools Hardware Materials Grounding the Refrigerator Step
13. ng Screw Leg Front Roller Adjust the Leveling Legs The leveling legs have two purposes e Leveling legs adjust so the refrigerator is firmly positioned on the floor and does not wobble e Leveling legs serve as a stabilizing brake to hold the refrigerator securely in position during operation and cleaning The leveling legs also prevent the refrigerator from tipping Turn the leveling legs clockwise to raise the refrigerator counterclockwise to lower it A CAUTI O N To avoid possible personal injury or property damage the leveling legs must be firmly touching the floor A P R U D E N C E e Afin d viter toute blessure corporelle ou dommage mat riel les pieds de support doivent tre en contact avec le sol 13 STEP 15 LEVEL THE DOORS If the doors are not evenly aligned at the top the refrigerator door can be adjusted e Use a 7 16 hex socket or wrench to turn the door adjusting screw Turn the screw to the right to raise the door turn left to lower the door _Doors Should Align at Top NOTE A nylon plug is imbedded in the threads of the pin The plug is designed to prevent the pin from turning A wrench must be used to turn the pin e Turn the wrench one or two times Open and close the refrigerator door to check alignment with the freezer door at the top Adjust again if necessary Installation Instructions STEP 16 INSTALL TOEKICK e Press toekick into position and reinstall
14. one screw on each side Toekick Screw M PO RTANT The vented toekick must remain unobstructed for proper air circulation REMOVE PACKAGING START ICEMAKER STEP 17 A Remove all tape foam and protective packing from shelves and drawers B Remove the tie downs from the freezer baskets Set the icemaker power switch to the on position The icemaker will not begin to operate until it reaches its operating temperature of 15 F 9 C or below It will then begin operation automatically It will take 2 3 days to fill the ice bin NOTE In lower water pressure conditions the water valve may turn on up to 3 times to deliver enough water to the icemaker 14 STEP 18 TEMPERATURE CONTROLS e The temperature controls are preset at 37 F for the refrigerator and 0 F for the freezer e Allow 24 hours to stabilize before making adjustments Notes 15 NOTE While performing installations described in this book safety glasses or goggles should be worn For Monogram local service in your area call 1 800 444 1845 NOTE Product improvement is a continuing endeavor at General Electric Therefore materials appearance and specifications are subject to change without notice GE Consumer amp Industrial 31 46515 Appliances 225D1974P005 General Electric Company 05 08 JR Louisville KY 40225 Printed in Mexico ge com
15. ons STEP 9 REPLACE FRESH FOOD DOORS A Lower the refrigerator door onto the center hinge pin Ensure that the plastic hinge pin thimble is on the center hinge pin or inside door hinge pin hole located in the bottom of the door Hinge Pin Securely tape the door shut with masking tape or have a second person support the door Insert the top hinge pin into the hinge hole on top of the refrigerator door Make sure the door is aligned with the cabinet and opposite door Attach the hinge to the top of the cabinet loosely with the bolts Make sure the gasket on the door is flush against the cabinet and is not folded Make sure the door is straight and the gap between the doors is even across the front While holding the aligned door in place tighten the top hinge bolts Gasket Flush and Not Folded Tighten Top Hinge Bolts Follow the same procedure on the opposite door Reinstall the top cap using the 4 screws removed earlier Top Cap Screws _ STEP 10 INSTALL WATER LINE e A cold water supply is required for automatic icemaker operation The water pressure must be between 40 and 120 p s i e Route GE SmartConnect Refrigerator Tubing or 1 4 OD copper tubing between house cold water line and the water connection location e Measure the distance from the water valve on the back of the refrigerator to the water supply line Add 8 foot length to allow the refrigerator to be moved away from the w
16. this refrigerator must be placed on a level surface of hard material that is at the same height as the rest of the flooring This surface should be strong enough to support a fully loaded refrigerator IMPORTANT NOTE Protect the finish of the flooring Cut a large section of the cardboard carton and place under the refrigerator where you are working DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE THIRD GROUND PRONG FROM THE POWER CORD DO NOT USE AN ADAPTER PLUG TO CONNECT THE REFRIGERATOR TO A 2 PRONG OUTLET DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE Installation Instructions A WARNING Under certain circumstances this refrigerator can tip forward Injury to persons can result Install Anti Tip Bracket packed with this refrigerator MEASURE CABINET OPENING AVAILABLE VS REFRIGERATOR WIDTH Measure width of cabinet opening where refrigerator will be placed W Be sure to account for any countertop overhang baseboard thickness and any clearance desired Width W should not be less than 36 inches The refrigerator will be placed approximately in the middle of this opening Rear Wall Baseboard Thickness gt lt or Countertop Overhang aa Whichever is Greater Plus Any Desired Clearance REFRIGERATOR RH Side STEP 2 LOCATE ANTI TIP BRACKET A Place the anti tip floor bracket locator template included inside the anti tip kit onto th
17. to the refrigerator is from a Reverse Osmosis Water System use the refrigerator s filter bypass plug You must also use the filter bypass plug when a replacement filter cartridge is not available The icemaker will not operate without the filter or filter bypass plug Replacement Filters To order additional filter cartridges in the United States visit our Website ge com or call GE Parts and Accessories 800 626 2002 Filter Model GSWF Customers in Canada should consult the yellow pages for the nearest Mabe Service Center 12 STEP 11 CONNECT WATER SUPPLY Check to be sure that refrigerator power cord is not plugged into the wall outlet Tubing Clamp 1 4 Tubing 1 4 Compression Nut Ferrule _ sleeve If you are using copper tubing e Place compression nut and ferrule sleeve onto the end of the tubing coming from the house water supply e Insert the end of the copper tubing into the refrigerator connection at the back of the refrigerator as far as possible Hold the tubing in place and tighten the fitting If you are using GE SmartConnect tubing e Insert the molded end of the tubing into the refrigerator connection at the back of the refrigerator and tighten the compression nut until it is hand tight e Then tighten one additional turn with a wrench Overtightening may cause leaks e Fasten the tubing into the clamp provided to hold it in position You may need to pry open the clamp

GE Monogram Drawer Freezer Refrigerator Refrigerator User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents