Gateway FPD2200 Computer Monitor User Manual
Contents
1. Display Modes Resolution Horizontal Freq kHz Vertical Freq Hz 1 VESA 640x480 31 469 60 2 VESA 800x600 35 156 56 3 VESA 800x600 37 879 60 4 VESA 1024 x 768 48 363 60 5 VESA 1280 x 960 60 000 60 6 VESA 1280 x 1024 63 981 60 7 1600 x 1024 64 350 60 Troubleshooting Check the following before calling for service Display Position is incorrect m Select AUTO in the OSD menu m If the results are unsatisfactory adjust the image position using the position icon in the on screen display On the screen background vertical bars or stripes are visible m Select AUTO in the OSD menu m f the results are unsatisfactory decrease the vertical bars or stripes using the CLOCK icon in the on screen display Any horizontal noise appearing in any image or characters are not clearly portraid m Select AUTO in the OSD menu m If the results are unsatisfactory decrease the horizontal bars using the PHASE icon in the on screen display Check signal Cable message m Thesignal cable is not connected or is loose Check and secure the connection OUT OF RANGE message appears Picture is blank m The frequency of the signal from the video card is outside the operating range of the monitor Horizontal Frequency 30kHz 70kHz Vertical Frequency 56Hz 61Hz Use the graphics board s utility software to change the frequency setting Refer to the manual for graphics board You can change the setup to the supported resolution us2. Gateway Gateway FPD2200 Flat Panel Display User s Guide P NO 3828TUO197A 0203 Rev00 Printed in Korea NPOCUICUONN lt c asarc a44 pepo oes aoe eos hea ep wee ah KORENE ew Ewe ee eek Al imporlant Precautions 2 s0 4nevsesassmesee toners estes EENAA ATS A2 Description 0F Controls lt 6 oscenctcsuecieeGadenatecseeees deans ne EUn TN A4 Connecting the MONON 2243210509 995p098 Sateen Paes Aah ee ire norrit A6 Connection of external equipment eessssssssnssssssosessesosessecosess A8 On Screen Display OSD Control Adjustment 0 cee cee ec eee ee eee eee A9 On Screen Display OSD Selection and Adjustment 00 c eee eee e eee A10 Video Memory Modes oi04242c00 c00 pence eieveess te cdendaeieuse senses uses A14 IKOUDIESNOOUNG veirsitsrrirr e er r rAr APOTE FEER ENEE ETEA PIRE A15 SPECHIICAUIONS e E EE E EEEE E S A16 Introduction The FPD2200 Flat Panel Monitor has an active matrix TFT Thin Film Transistor LCD Liquid Crystal Display Features The FPD2200 is a 22 inch 55 8cm viewable intelligent micro processor based monitor This monitor can be connected to a VCR or DVD The monitor has two signal connectors D sub and DVI D so that it can support both an existing analog input D sub and an advanced standard digital input DVI D Two computers can be simultaneously used while connected to this monitor This monitor has a picture in picture function so that you can watch from VCR
3. DVD while using a computer The aspect ratio of the monitor is 16 10 so that you can feel as if you are watching a film in a theater You can also simultaneously display two pages of a document set to an A4 size on the monitor so that working efficiency can be improved Digitally controlled auto Scanning is done with the micro processor for honzontal scan frequencies between 30 and 70kHz and vertical scan frequencies between 56 61Hz We accomplished to adapt the advanced design and technology to the monitor Soft touch buttons on the front panel are simple and allow you to conveniently adjust a vaniety of image controls a This monitor has DDC 2B function Important Precautions This unit has been engineered and manufactured to ensure your personal safety however improper use may result in potential e shock or fire hazards In order to allow the proper operation of all safeguards incorporated in this display observe the following basic rules for its installation use and servicing On Safety Use only the power cord supplied with the unit In case you use another power cord make sure that it is certified by the applicable national standards if not being provided by the supplier If the power cable is faulty in any way please contact the manufacturer or the nearest authonzed repair service provider for a replacement The power supply cord is used as the main disconnection device Ensure that the socket outlet is easily
4. accessible after installation Operate the display only from a power source indicated in the specifications of this manual or listed on the display If you are not sure what type of power supply you have in your home consult with your dealer Overloaded AC outlets and extension cords are dangerous So are frayed power cords and broken plugs They may result in a shock or fire hazard Call your service technician for replacement Do not Open the Display There are no user serviceable components inside There are Dangerous High Voltages inside even when the power is OFF Contact your dealer if the display is not operating propery To Avoid Personal Injury Do not place the display on a sloping shelf unless propery secured Use only a stand recommended by the manufacturer Do not try to roll a stand with small casters across thresholds or deep pile carpets To Prevent Fire or Hazards Always tum the display OFF if you leave the room for more than a short period of time Never leave the display ON when leaving the house Keep children from dropping or pushing objects into the display s cabinet openings Some intemal parts carry hazardous voltages Do not add accessones that have not been designed for this display a Dunng a lightning storm or when the display is to be left unattended for an extended penod of time unplug it from the wall outlet Important Precautions On Installation Do not allow anyth
5. cm 18 4 inches Depth 7 3 cm 2 87 inches Power Input DC 15V 5 0A AC Adapter Input AC 100 240V 50 60Hz 15A Output DC 15V 5 33A O C Weight Net 14 8 kg 32 6 lbs Tilt Range 10 30 Environment Operating condition Conditions Temperature 10Cto35C Humidity 20 to 80 non condensing Storage condition Temperature 20Cto60C Humidity 5 to 90 non condensing NOTE a Information in this document is subject to change without notice
6. OSITION gt i TRANSPARENCY NE 50 BEEP gt ON ZOOM gt E 1024 x 768 48 3 kHz 60Hz ELAPSED TIME 00000H AUTO CLOCK PHASE LANGUAGE This function is suitable for analog signal input only This button is for the automatic adjustment of the screen position clock and phase To minimize any vertical bars or stripes visible on the screen background The horizontal screen size will also change To adjust the focus of the display This item allows you to remove any horizontal noise and clear or sharpen the image of characters Phase adjustment should be done after adjusting the Clock To choose the language in which the control names are displayed IMAGE SIZE This function displays the image in its original size or enlarged size so as to fit in the full screen of the LCD panel OSD POSITION To adjust position of the OSD window TRANSPARENCY BEEP ZOOM ELAPSED TIME on the screen Press the SET button to display the submenu for OSD POSITION OSD POSITION HORIZONTAL 50 VERTICAL 50 To adjust the transparency of the OSD menu screen To select beep on or off To adjust horizontal and vertical image size simultaneously If you want to move the zooming point use the H V POSITION function in the sub menu However if the monitor turns off when zooming in and out the screen the monitor will be returned to original screen It show how long the monitor has
7. ar panel of the computer and tighten the screws Be sure the signal cable aligns with the D Sub connector MAC Connect one end of the monitor signal cable to the input connector on the rear panel of the monitor Connect the other end of the monitor signal cable to the rear panel of Macintosh computer through a Macintosh adapter and then tighten screws Figu re 1 DC Power DVI D connector connector x There should be a DVI D port on zn the computer 5 O og DVI D Power Cord AC adapter Signal Cable Connecting the Monitor DC Power connector D sub connector Figure 2 a a S Video Video IN i 7 1 a fie Signal Cable MAC Adapter 2 he Signal Cable Note The figure shows the connection to an Apple Macintosh using a separately purchased adapter For more information on adapter requirements contact your authorized dealer reseller or service provider 2 Connect the plug from the AC adapter into the back of the monitor 3 Connect one end of the AC power cord to the AC adapter and the other end to a properly grounded AC outlet that is easily accessible and close to the monitor Connection of external equipment Connecting the VCR DVD 1 Connect the audio video output jacks of th
8. been used On Screen Display OSD Selection and Adjustment OSD Adjust Description This PIP Picture in Picture function allows the image from the VCR or DVD to be displayed ona sub screen while you are using a computer PIP SOURCE gt VI AV PIP 3 z PIP SIZE gt LARGE PIP POSITION EE PIP To select the sub screen on off PIP IMAGE gt m ON OFF PIP To select an input signal for PIP SOURCE V1 AV V2 S PIP SIZE To adjust the size of the PIP screen SMALL MEDIUM LARGE PIP To adjust the position of PIP screen POSITION Press the SET button to display the submenu for PIP POSITION 2 3 v ANA SIAN Se PIP POSITION HORIZONTAL 50 VERTICAL 50 PIP To adjust the image of the PIP screen IMAGE Press the SET button to display the submenu for PIP IMAGE Use the LEFT RIGHT lt gt buttons to adjust the item to the desired level PIP IMAGE PIP CONTRAST E 53 PIP BRIGHTNESS MEE 70 PIP SHARPNESS EE 50 PIP COLOR es 50 PIP TINT EH PIP CONTRAST Adjust the display to the contrast desired PIP BRIGHTNESS Used to adjust the brightness of the screen PIP SHARPNESS To adjust the clearness of the screen PIP COLOR To adjust the color to desired level PIP TINT To adjust the tint to desired level This function is available only in NTSC broadcasting mode On Screen Display OSD Selection and Adjustment Adju
9. e VCR DVD to the corresponding input ports of the set If you connect the S Video input port to extemal equipment you can enjoy high definition display e Monitor RCA cable optional S Video Video IN TR i e VCR DVD S Video cable optional 2 Select an input signal SOURCE Y DOWN UPA SET Press the SOURCE button on the front panel of the gt 00 Om 0 monitor to select an input V1 AV Composite video INPUT SELECT V2 S S video DVI DIGITAL DSUB ANALOG V1 AV v2 S On Screen Display OSD Control Adjustment Making adjustments to the image size position and operating parameters of the monitor are quick and easy with the On Screen Display Control system A quick example is given below to familiarize you with the use of the controls Following section is an outline of the available adjustments and selections you can make using the OSD NOTE Allow the monitor to stabilize for at least 30 minutes before making image adjustment To make adjustments in the On Screen Display follow these steps MENU vVDOWN UP A SET 0 MENU SET lt LEFT RIGHT gt Y DOWN UP A 0 0 0 Press the MENU Button the main menu of the OSD will appear To access a control use the DOWN UP w a Buttons When the desired control icon is highlighted press the SET Button Press the DOWN UP w a Buttons to select the desired item Use the LEFT RIGHT gt Buttons to adjust the i
10. g mode stand by suspend power off this indicator color changes to amber Power Button Use this button to turn the monitor on or off Oc Description of Controls Rear Panel Controls Connected to another object stand type and wall mounted type optional ANNAN EC DC15V P A e Locking slot connected to a locking cable that can be purchased separately at most computer stores Composite Video DC Power Connector D sub Connector Input Jack DC15 S Video Video D z cmm Ep O DVI D Connector S Video Input Jack Connecting the Monitor To set up the monitor ensure that the power is turned off to the monitor computer system and other attached devices Connect the cables to the monitor with it lying on a cushion or a cloth Follow these steps r Using the Computer 1 Connect the signal cable E When connecting the DVI D signal cable aus Figure 1 Connect one end of the monitor signal cable to the input connector on the rear panel of the monitor Connect the other end to the DVI D connector on the rear panel of the computer and tighten the screws Be sure the signal cable aligns with the DVI D connector E When connecting the D Sub signal cable wu Figure 2 Connect one end of the monitor signal cable to the input connector on the rear panel of the monitor Connect the other end to the D Sub connector on the re
11. ing the Safe Mode Press the F8 key during booting the system The power LED is illuminated amber a Themonitor is in its display power management mode m There is no active signal coming from the PC m The signal cable is not fastened securely m Check the computer power and graphics adapter configuration The monitor doesn t enter the power saving off mode Amber Computer video signal is not VESA DPMS standard Either the PC or the video controller card is not using the VESA DPMS power management function NOTE a If the power indicator LED light is blinking amber may result in abnomal condition of the monitor Then press a power ON OFF button on the front panel control and call your service technician for more information Specifications Display Type 22inch 55 8cm Wide SXGA TFT LCD Anti Glare coating Viewable Size 22inch 55 8cm Viewing Angle max 70 Left Right Up Down Pixel pitch 0 294 x 0 294mm True color 16 7 million color Sync Input Horizontal Freq 30kHz 70kHz Automatic Vertical Freq 56Hz 61Hz Automatic Input form Separate TTL Positive Negative Digital Video Input Signal input 15 pin D Sub connector DVI D connector Input Form Separate RGB Analog 0 7Vp p 750hm Positive Digital Resolution max Analog 1600 x 1024 60Hz Digital 1600 x 1024 60Hz Power Normal lt 80W Consumption Stand by Suspend lt 8W Power Off lt 8W Dimensions Width 58 2 cm 22 9 inches Height 46 75
12. ing to rest upon or roll over the power cord and do not place the display where the power cord is subject to damage Do not use this display near water such as near a bathtub washbowl kitchen sink laundry tub in a wet basement or near a swimming pool Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation If these openings are blocked built up heat can cause failures which may result in a fire hazard Therefore NEVER Block the bottom ventilation slots by placing the display on a bed sofa rug etc a Place the display in a built in enclosure unless proper ventilation is provided Cover the openings with cloth or other matenal Place the display near or over a radiator or heat source Do not rub or strike the Active M atrix LCD with anything hard as this may scratch mar or damage the Active M atnx LCD permanently Do not press the LCD screen with your finger for a long time as this may cause some afterimages Some dot defects may appear as Red Green or Blue spots on the screen However this will have no impact or effect on the display performance If possible use the recommended resolution to obtain the best image quality for your LCD display If used under any mode except the recommended resolution some scaled or processed images may appear on the screen However this is charactenstic of the fixed resolution LCD panel On Cleaning Unplug the disp
13. lay before cleaning the face of the display screen Use a slightly damp not wet cloth Do not use an aerosol directly on the display screen because over spraying may cause electrical shock On Repacking Do not throw away the carton and packing matenals They make an ideal container in which to transport the unit When shipping the unit to another location repack it in its original maternal Description of Controls Front Panel Controls MENU Button SET Button Power Button SOURCE MENU Y DOWN UP A lt LEFT RIGHT gt SET 9 SOURCE Selection Button DOWN UP V A LEFT RIGHT 4 D Power Indicator Buttons Buttons Control Function source SOURCE Selection Use this button to select an input signal Button SOURCE Y DOWN UPA SET gt INPUT SELECT a DET e DVI DIGITAL DVI digital signal n pi e DSUB ANALOG 15 pin D sub analog signal er e V1 AV Composite video e V2 S S video MENU Button Use this button to enter or exit the On Screen Display voowwupea DOWN UP w a Use these buttons to choose or adjust items in the Buttons On Screen Display lt eFTRIGHT gt LEFT RIGHT lt gt Use these buttons to choose or adjust items in the Buttons On Screen Display SET Button Use this button to enter a selection in the On Screen Display o Power Indicator This indicator lights up green when the monitor operates normally If the monitor is in DPM Energy Savin
14. sting the Screen when Using VCR DVD V1 V2 ADJUSTMENT CONTRAST BRIGHTNESS SHARPNESS jeje Me TINT SETUP IMAGE SIZE gt FULL OSD POSITION O TRANSPARENCY MEM O BEEP gt ON CONTRAST Adjust the display to the contrast desired BRIGHTNESS Used to adjust the brightness of the screen SHARPNESS To adjust the clearness of the screen COLOR To adjust the color to desired level TINT To adjust the tint to desired level This function is available only in NTSC broadcasting mode LANGUAGE To choose the language in which the control names are displayed IMAGE SIZE This function displays the image in its original size or enlarged size so as to fit in the full screen of the LCD panel QSDPOSITION To adjust position of the OSD window on the screen Press the SET button to display the submenu for OSD POSITION HORIZONTAL 50 VERTICAL 50 TRANSPARENCY To adjust the transparency of the OSD menu screen BEEP To select beep on or off Video Memory Modes The display modes listed below are the most commonly used modes and are set as factory defaults The monitor automatically recognizes most input data modes and displays centered images with the proper sizing If the screen size is inappropriately set or the display is not centered you need to readjust the parameters of the monitor using the OSD on screen display Display Modes Resolution
15. tem to the desired level Accept the changes by pressing the SET Button Exit the OSD by Pressing the MENU Button aso N On Screen Display OSD Selection and Adjustment You were introduced to the procedure of selection and adjusting an item using the OSD system Listed below are the icons icon names and icon descriptions of the items that are shown on the Menu Adjusting the Screen when Using a Computer Note When input is set as a digital signal only the BRIGHTNESS SETUP and PIP items can be adjusted You do not need to adjust the other items OSD Adjust Description CONTRAST BRIGHTNESS BRIGHTNESS 100 CONTRAST 100 COLOR ADJUSTMENT GREEN 50 BLUE es O IMAGE POSITION HORIZONTAL 50 VERTICAL 50 OO USER 9300K 6500K Brightness Used to adjust the brightness of the screen Contrast Adjust the display to the contrast desired RED GREEN BLUE To set your own color levels To appear the displays color temperature e 9300K Slightly bluish white e 6500K Slightly reddish white I O Horizontal Position ad To move picture image left and right Vertical Position TO move image up and down On Screen Display OSD Selection and Adjustment OSD Adjust Description Pb SPE TRACKING CLOCK Eee 50 PHASE Eee 50 9 E POL bE SETUP LANGUAGE gt ENGLISH IMAGE SIZE gt FULL OSD P
Download Pdf Manuals
Related Search