Fisher-Price 79030 Bouncy Seat User Manual
Contents
1. Model Number 79030 Please keep this instruction sheet for future reference as it contains important information Adult assembly is required Tool required for assembly Phillips screwdriver not included Requires one D LR20 alkaline battery not included for soother operation three D LR20 alkaline batteries not included for toy bar operation Fisher Price Warning A WARNING To prevent serious injury and or falls e Never use on any elevated surface since child s movement may cause bouncer to slide or tip over e Never use as a carrier or lift while child is seated e Always use the restraint system e Never leave child unattended e Never use as a Car seat e Never use with a child able to sit up unassisted Consumer Information Occasionally a consumer may experience a problem with one of our products If this should happen please call us toll free rather than return this product to the store Usually we can solve the problem over the telephone or send you replacement parts Please call Fisher Price Consumer Relations toll free at 1 800 432 KIDS 8 AM 6 PM EST Monday through Friday Hearing impaired consumers using TTY TDD equipment please call 1 800 382 7470 Or write to Fisher Price Consumer Relations 636 Girard Avenue East Aurora New York 14052 Parts Removable Teether Rings Footrest with Electronic Unit Right Base Wire ANNAN2. Restraint Restraint Pad Securing Your Child If the toy bar is attached remove it before placing your child in the seat e Place your child in the seat Position the restraint between your child s legs e Fasten both restraint belts to the buckles on each side of the restraint pad Make sure you hear a click on both sides Check to be sure the restraint is securely attached by pulling it away from your child The restraint should remain attached e Attach the toy bar if desired see Assembly step 8 14 Set Up amp Use Anchored End Anchored End Free End Tighten Loosen To tighten the belts Feed the anchored end of the belt up through the buckle to form a loop Q Pull the free end of the belt e Repeat this procedure to tighten the other belt To loosen the belts Feed the free end of the belt up through the buckle to form a loop Q Enlarge the loop by pulling on the end of the loop toward the buckle Pull the anchored end of the belt to shorten the free end of the belt e Repeat this procedure to loosen the other belt Please Note After adjusting the belts to fit your child make sure you pull on them to be sure they are securely fastened Calming Vibrations e Make sure your child is properly secured in the seat e To turn vibrations on slide the power switch on the electronic unit to the on position e To turn vibrations off slide the power switch on the
3. 16 Set Up amp Use 6 Parent Activated Coe 1 amp 0 6 Lk ee Mode Switch 4 GC 600 a Sound Selection Button f 0 r Volume Switch o Slide the mode switch to for parent activated mode Baby enjoys 10 minutes of music lights and bubbling action e Select music or sounds or no sound at all Push the sound selection button again and again for ov Lullabies D Ocean Waves Q Summer Rain Babbling Brook No Sound Slide the volume switch to 4 for low volume for high volume e The toy bar automatically turns off after approximately 10 minutes To turn the toy bar back on simply slide the mode switch off and then back on again or press the sound selection button Slide the mode switch to O to turn off sounds bubbling action and lights IMPORTANT If lights become dim sound becomes faint bubbling action slows or the toy bar operates erratically or does not turn off remove the three batteries from the large battery compartment in the electronic unit Dispose of the batteries properly Replace the batteries with three new D LR20 alkaline batteries 17 Set Up amp Use i Virar n tin B Repi f e The teethers are removable from the toys on the toy bar Simply twist the ends of each teether slightly to remove from either toy e To replace a teether simply push to attach it to the bottom of either toy 18 Set Up amp Use Remove the Toy Bar
4. electronic unit to the off position O IMPORTANT If vibrations from the electronic unit become faint or if there are no vibrations remove the battery from the small battery compartment T in the electronic unit and dispose of it properly Replace the battery with a new D LR20 alkaline battery 15 Set Up amp Use Baby Activated Bat Toys for Sounds or Music Bubbling Action A cin and Lights 6 0 Nes Mode Switch o 4 Nes Volume Switch Slide the mode switch to amp for baby activated mode e When baby bats either toy baby is rewarded with wave sounds bubbling action and lights Hint Each time baby bats either toy baby is rewarded with a different sound and light pattern Note that the sound selection button D Q does not work in baby activated mode Slide the volume switch to 4 for low volume for high volume The toy bar automatically turns off after approximately 10 minutes from the last time baby bats a toy To turn the toy bar back on simply bat either toy e Slide the mode switch to O to turn off sounds bubbling action and lights IMPORTANT If lights become dim sound becomes faint bubbling action slows or the toy bar operates erratically or does not turn off remove the three batteries from the large battery compartment in the electronic unit Dispose of the batteries properly Replace the batteries with three new D LR20 alkaline batteries
5. 8 x 3 4 Screw 2 Shown Actual Size d Left Base Wire Battery Installation Soother Toy Bar Battery Compartment Battery Compartment Locate the electronic unit on the footrest wire You will see that there are two battery compartments The smaller battery compartment wa powers the soother the larger battery compartment powers the toy bar First loosen the screw in the soother battery compartment door with a Phillips screwdriver Remove the battery compartment door Insert one D LR20 alkaline battery as indicated inside the battery compartment e Replace the battery compartment door Tighten the screw with a Phillips screwdriver Do not over tighten e Next loosen the screws in the toy bar battery compartment door with a Phillips screwdriver Insert three D LR20 alkaline batteries as indicated inside the battery compartment e Replace the battery compartment door Tighten the screws with a Phillips screwdriver Do not over tighten Battery Tips 1 5V Soother 1 5V x 3 Toy Bar D LR20 SHOWN ACTUAL SIZE e Do not mix old and new batteries e Do not mix different types of batteries alkaline standard carbon zinc or rechargeable nickel cadmium e Remove the batteries during long periods of non use Always remove exhausted batteries from the toy Battery leakage and corrosion can damage this product Dispose of batteries safely e Do not dispose of batteries in a
6. Pull the ends of the latches out and lift the toy bar Care The pad is machine washable Wash the pad separately in cold water on the gentle cycle Do not use bleach Tumble dry separately on low heat and remove promptly The frame toy bar and teethers can be wiped clean using a mild cleaning solution and a damp cloth Do not immerse the electronic unit or toy bar To remove the pad e Lift the footrest and remove the pad lower pocket e Push the restraint belts back through the pad e Slide the pad upper pocket off the seat back tube To re assemble the pad e Refer to Assembly steps 6 and 7 19 FCC Note United States Only Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the re
7. ake sure both colored tabs on the base wires are visible through the holes in the base tube Assembly Electronic Unit Battery Compartment Doors Up e Position the footrest so that the electronic unit battery compartment doors are upright e While flexing the base wires toward each other hook the footrest onto the ends of the base wires e Push the footrest down completely to the tabs on the base wires Assembly IMPORTANT You MUST position the seat back tube correctly for proper assembly of this product Seat Back Tube Bends Backward Circles Match ATriangles Match Position the seat back tube so that it bends backward Match the colored symbol on the seat back tube to the colored symbol on the base wire circles on one side and A triangles on the other side If the colored symbols do not match turn the seat back tube over and try again Fit the seat back tube completely onto the base wires Assembly Retainers e Fit a retainer rounded side inward to one end of the seat back tube Insert a screw through the outside hole in the seat back tube and into the retainer e While holding the retainer in place tighten the screw with a Phillips screwdriver Do not over tighten e Repeat this procedure to secure the other side of the seat back tube to the base assembly using the remaining retainer and screw Assembly Tube Bends Seat Back a N Backward e Check to be sure the seat bac
8. ceiving antenna e Increase the separation between the equipment and receiver Consult the dealer or an experienced radio TV technician for help Note Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user s authority to operate the equipment E y Ms i h gt i For other countries outside the United States Canada call 1 800 567 7724 or write to Mattel Canada Inc 6155 Freemont Blvd Mississauga Ontario L5R 3W2 Great Britain telephone 01628 500302 Australia Mattel Australia Pty Ltd 658 Church Street Locked Bag 870 Richmond Victoria 3121 Australia Consumer Advisory Service 1300 135 312 New Zealand 16 18 William Pickering Drive Albany 1331 Auckland Fisher Price Inc a subsidiary of Mattel Inc East Aurora NY 14052 U S A 2002 Mattel Inc All Rights Reserved and designate U S trademarks of Mattel Inc Printed in China 79030a 0920
9. fire The batteries may explode or leak e Never short circuit the battery terminals e Non rechargeable batteries are not to be recharged Only batteries of the same or equivalent type as recommended in the Battery Installation instructions are to be used If removable rechargeable batteries are used they are only to be charged under adult supervision e Rechargeable batteries are to be removed from the product before they are charged If you use a battery charger it should be examined regularly for damage to the cord plug enclosure and other parts Do not use a damaged battery charger until it has been properly repaired e Low battery power in the toy bar may cause it to operate erratically no sounds no lights no bubbling action and the toy bar may not turn off If this should happen remove and discard all three batteries in the large battery compartment RA and replace with three new D LR20 alkaline batteries Assembly A CAUTION This package contains small parts in its unassembled state Adult assembly is required Right Base Wire Colored Tabs Left Base Wire _ ape Place the base tube on a flat surface as shown Position the left and right base wires as shown Note the location of the colored tab on the left and right base wires Colored Tab Base Wire Fit the left base wire into the base tube T ay d ee BackView mut Fit the right base wire into the base tube acie M
10. k tube bends backward e Pull the seat back tube up to be sure it is secure If the seat back tube does not bend backward or you can remove either end of the seat back tube you have not assembled it correctly Remove the screws and retainers Re read and repeat Assembly steps 3 5 10 Assembly Pad Footrest Seat Back Tube e Unbuckle the restraint belts from the restraint pad Push the restraint belts back through the slots in the pad Q Fit the pad upper pocket onto the seat back tube Lift the footrest Fit the pad lower pocket onto the footrest Lower the footrest 11 Assembly Fit both restraint belts back through the pad slots as shown 12 Assembly e Insert and snap the ends of the toy bar into the sockets in the footrest Hint The square end of the toy bar fits into the square socket and the circular end of the toy bar fits into the circular socket e Make sure the toy bar latches are secure The small tabs on the sockets should be visible in the opening in the latches Assembly is now complete 13 Set Up amp Use A WARNING To prevent serious injury and or falls e Never use on any elevated surface since child s movement may cause bouncer to slide or tip over e Never use as a carrier or lift while child is seated e Always use the restraint system e Never leave child unattended e Never use with a child able to sit up unassisted
Download Pdf Manuals
Related Search