Eltax Cinema DVD Home Theatre System Vision DVD Home Theatre System DVD Player User Manual
Contents
1. A I Subwoofer Front speaker Center speaker 3 ANTENNA ww KE Surround speaker Surround speaker 11 Radio signals may be difficult to receive in some buildings and under certain conditions The provided antennas will help in their reception They are intended for indoor use only AM Loop Antenna The placement of the AM loop antenna should be in a direction that provides the clearest reception Keep as far as possible from DVD receiver TV set and speaker and power cords If reception remains poor an outdoor antenna may be necessary To connect the AM loop antenna 1 Hold down handle 2 Insert wire end into hole 3 Release handle Position for best reception 1 K Ae Ze P FM Indoor Antenna The FM antenna should be fully extended andina direction that provides the clearest signal Secure the antenna ends in a location where distortion is a minimum If reception remains poor an outdoor antenna may be necessary CJ 750 Outdoor AM antenna Coaxial cable 75 ohm N I C 4 Coaxial cable 75 ohm Outdoor FM antenna2. SC e hn aran Paet nersyty ytis 1 Safety Information sss 2 Table of Contents sse 3 About Your DVD Player 0 4 Best LocatiONi ississssivavaan etsi ttes eet ie nane 4 To Obtain a Clear Picture 4 Playable Discs eren e enhn 4 Digital Audio Output 4 Laser Head Over Current Protection System 4 WS6 OF DISC mats ertet 5 Randiin snai nn n e E aE E AEREE IE 5 GGA E M 5 be PEERS 5 Front and Back panels 0000 6 Sein TE 6 Back Panel eerte inen tea vana a aan ERR EN anna 6 Remote Control 7 Operating the remote control 8 Connecting Devices sess 9 Nri gek aa kirna ak ad a 10 Arrangement of speakerg nnen 10 Connecting speakers a 11 Connecting antennag rat 12 Connecting power Supp 13 Playing the radio 0 0 00 ene nr 14 Basic DVD operatton nenne 15 Inte tel Sk 16 System Getup annan an n a naa anaanen 19 DVD Menu Setup 0 0 0 000 ner 19 LANGUAGE Setup a a FE A ASA 19 Video Sets hed saa Sg a at a 4 21 AUGIO SQtUp asni a a Sie ae ch 22 More Audio Geiup rr 23 Rating Setup sa aaa pa bj a 24 Mp runcton nananana i 25 JPEG files iiie ce cnini ci asa kaataneet 26 Trouble shooting 26 Technical specifications 27 The following will help you get the most enjoyment from your DVD receiver system BEST
3. Battery Installation 1 Push down and out on the battery Compart ment cover to remove it 2 Insert the two AAA batteries into the battery compartment of the remote control making sure the and signs on the batteries and inside the battery compartment match up 3 Replace the battery compartment cover Notes e Do not mix batteries from different manu facturers nor old ones with new e f the remote control will not be used for an extended period of time remove the batteries to prevent damage causing corrosion e Remove dead batteries immediately to prevent damage causing corrosion e f battery leakage occurs wipe the battery liquid from the battery compartment then replace both batteries Always replace both batteries at the same time using new fully charged batteries e Life expectancy of batteries may vary depending on amount of use Using the Remote Control Point the remote control at the remote sensor on the DVD receiver When the signal is received from the remote the unit will function accordingly The remote will operate to approximately 16 from the remote sensor at an angle of around 30 each direction Notes e Do not direct the remote sensor toward any light source such as direct sunlight or a strong fluorescent light as it may cause the unit to not operate correctly e When other remote controls are used nearby or when the remote is used near equipment using infrared rays interferen
4. 4 Check if parental lock function is on 5 Make sure disc is for use in region Remote does not work 1 Check batteries possibly replace 2 Check to ensure there isn t any obstacles between the remote sensor onthe unit s front panel and the remote control 3 Be sure the remote is aimed at the remote sensor Divided picture 1 Check that disc scratches 2 The unit is controlled by a micro computer which may need to be reset Turn off the unit s power wait several seconds then turn back on No color picture 1 Check to see if the S connector is damag ed bent pin MP3 discs don tplay 1 Use another software edition to reburn disc as the edition used may not be com patible with the player 2 Use new editions of software such as Audio station 4 Easy CD Creator To ast Titanium etc 3 Make sure MP3 file is not encoded with a variable bit rate such as provided by Real Networks is clean and has no 622911 DVD Player TV System Compatible Discs Resolution Ratio Video S N Ratio Freguency Response Audio S N Ratio Degree of Distortion D A Converter Video Out S Video Out Audio Out Digital Audio Output Connections FM Tuner Tuning Range S N Ratio Monophonic Stereo Selectance THD Monophonic Stereo Freguency Response Stereo Resolution AM Tuner Tuning Range S N Ratio THD Amplifier MAX Output Power NTSC PAL DVD CD Mp3 JPEG CD R CD RW Greater Than 500 lines
5. 622 POWER HOME THEATRE SYSTEM 00060 Before plugging the power cord into the AC outlet check to make sure all of the connections have been properly completed When they have been carefully plug power cord into outlet Press the POWER button on the front pane to power the unit The display panel will light When the unit is initially powered a brief surge of electricity may cause interference with other electronic eguipment on the same circuit If this occurs connect the unit toan outleton a different circuit BASIC OPERATION Selecting Sound Source 1 Press any function button DVD TUNER TV AUX to select the desired sound source The appropriate symbol will appear in the display 2 When the TUNER button is pressed the last station listened to will play Note The desired program source will not play unless it and the selected signal button coincide with the active program source signal input Volume Control The volume may be adjusted by either turning the large volumeknob on the front panel or using the appropriate volume button on the remote control Mute Pressing the MUTE button temporarily mutes every speaker To resume audio press MUTE button again DVD TUNER TV AUX jar OQ cC MONO J CHSEL TUN O c oo ooe Tuner button Number button 14 00060 Positioning 1 Press TU
6. 65dB fs 96KHz 24bit 4Hz 44KHz 2dB 95dB lt 0 01 192KHz 24bit 1Vp p Y 1Vp p 75Q C 0 3Vp p 759 2 0V 5 1 Channel Coaxial SCART CVBS S Video 2 Channel Output 87 5 108MHz gt 46dB gt 46dB gt 50dB DIN 50dB 2 3 30Hz 10kHz 1dB 35dB 1kHz 30dB 100Hz 10kHz 522 1620KHz 35dB 3 5 x 20 W 4ohm musicpower 1 x 40 W 80hm musicpower S N Ratio Input Sensitivity Channel Seperation gt 76dB 350mv 47k gt 30dB Normal Remote Control Transmitter Signal Range Power Source Infrared Ray Approximately 5m 2 AAA Batteries General Power Supply AC 230 50Hz Consumed Power 60W Size WxHxD Because its products are subject to continuous improvement We reserves the right to modify product design and or specifications without notice and without incurring any obligations eltax www eltax com
7. 6 INPUT SIGNAL SOURCE This button is used to select the input source Note You may not hear any sound if the input selected has not been connected to any unit 7 VOLUME This button is used to adjust the volume of all six channels simultaneously 7 FRONT MAIN For connection of front speakers 8 CENTER SUBWOOFER For connection of center speaker and subwoofer 9 COAXIAL OUTPUT 10 230V 50Hz This unit is supplied with a power cord Make sure that the pins are dry before inserting the plug into a wall socket Do not pull the cord or step on it 11 SCART INPUT OUTPUT 12 OPTICAL OUTPUT 13 OUTPUT FOR ACTIVE SUBWOOFER For connection of an active subwoofer DVD TUNER TV 9 a LASTEN Suz PROG SETUP C39 C C C 1 2 3 4 gt gt 5 6 7 8 9 0 10 REPEAT b SUBTITLE AUDIO DISP ANGLE D D D 3 akti I N MENU ZOOM SLOW TITLE C C C C COOH COCO 1D VOLUME OOO 000600 0006 QOO N 800006 006 0000000000000000 ee eekleg OPEN CLOSE DVD AUX FM AM TUNER TV MONO CH SEL SETUP PRE TUN PROG 0 9 DIGITS 10 REPEAT AUDIO DISPLAY SUBTITLE ANGLE MENU TITLE Z00M SLOW PREVIOUS DOWN NEXT UP ENTER SCROLL UP SCROLL LEFT SCROLL RIGHT REWIND MEMO SCROLL DOWN FORWARD AUTO PLAY MUTE STOP PAUSE VOLUME INCREASE VOLUME DECREASE RE
8. LOCATION The unit should be placed on a firm flat surface away from VCRs stereos radios or large speakers as the magnetic flux from these devices may cause distortion in the sound and a poor picture If placed in a cabinet be sure there is atleast 1 of free space completely around the unit for proper ventilation TO OBTAIN A CLEAR PICTURE A DVD receiver is a precision device If the optical pick up lens and disc drive parts become dirty or worn down picture quality will become poor To obtain aclear picture regular inspection and maintenance are recommended every 1 000 hours of use depending onthe operating environment Contact dealer for details PLAYABLE DISCS This DVD receiver system will play the following types of discs DVD MP3 CD CD R and CD RW with super error correction ability It is also capable of displaying picture CDs and digital photo albums It supports eight languages up to 32 subtitles and multi angle viewing It features easy setup and operation with on screen menus It has full function CPU up grade able capability DIGITAL AUDIO OUTPUT The unit s coaxial output capability enables you to connectan external six channel AV amplifier and processor with built in Dolby Digital code and MPEG modulating capacity with just one cord This enables you to conveniently enjoy different DVD CD and Mp3 discs ANALOG AUDIO OUTPUT Speaker system plug and play convenience through the built in six channel power amplifier
9. Select Test Tone and press ENTER DRC Ge Right D Select the desired test tone setting and ES aan press ENTER E Press SETUP to save and exit the setup menu DRC settings DRC stands for Dynamic Range Compression A When the disc has stopped press SETUP B Select More Audio and press ENTER C Select Test Tone and press ENTER D Select the desired test tone setting and press ENTER Prologic On ON Compresses the sound effects in a movie Subwoofer On in relation to speech DS ESA OFF Default The sound will remain LPCM 96k On Uncompressed E Press SETUP to save and exit the setup menu LPCM settings More Aud A When the disc has stopped press We SETUP Prologic On B Select More Audio and press ENTER R Or est Tone Off G Select LPCM and press ENTER DRC Off D Select the desired LPCM setting and LPCM 96k press ENTER E E Press SETUP to save and exit the setup menu Rating Setup Rating includes Password Rating Last Memory and 1 Kid Safe Reset 2 G Password locks the rating setting There is no Password 3 PG factory set password You can enter your own passwordl Rating 4 PG 13 It must contain four numbers The default password is iastMemory On ei 8888 in case you forget your own password LOAD Factory Reset 7 NC 17 8 Adult Rating can be set as you please and depending on the level certain movies will be blocked Note Not all movies can be locked this way Last Memory allows yo
10. a photo SMART NAV 3 The function is only active in the photo displayed when a number key has been pressed How to play by menu 1 Insert the disc then the machine will start searching for disc information and the photos will be displayed automatically If you press stop the main menu will be displayed 2 Press a number key to select a photo Press the PLAY key to start Press the SCROLL key to select photos and then press PLAY 3 In stop mode you press SCROLL to select other photos 26 This handy trouble shooting guide is provided to save you time in case you experience any inconvenience with this DVD player Ifthe problem is not listed or if the provided solution does not correct the problem please call our customer support department Problem Possible Solution No power 1 Check to ensure that the power plug is securely in the wall outlet No sound 1 Check the connection between the DVD player and the TV set amplifier or any other unit it is connected to 2 Checkto ensure the TV and amplifier are in the correct mode No picture 1 Check the connection between the DVD player and the TV set or any other unit it is connected to 2 Check to make sure TV is turned on Disc does notplay 1 Check to make sure the disc is loaded correctly label side facing up on disc tray 2 Check that disc is clean from dirt dust fingerprints and smudges 3 Check to ensure disc is with in the guides on the tray
11. menu will appear Select the desired language by pressing the AUDIO key Note The disc being played must be multi lan guage encoded LOCATING A TITLE DVD discs are normally divided into titles which are then sub divided into chapters A specific title can be easily found with this unit Specific titles can be found using either the title menu function ifthe DVD disc contains a title menu or through its unique title number Title Menu Function 1 Press the TITLE key The title menu will appear on the TV screen 2 Press the appropriate scroll key to select the desired title Atitle may also be located by pressing its assigned number with the number buttons 3 Press the ENTER key This will start playback from chapter 1 of the selected title Note Some discs do not respond to this function If different instructions appear on the TV screen follow those instructions The Instructions given here describe the basic procedure Procedures may vary depending on the content of the DVD disc When playing a VCD2 0 disc TITLE key can be used to return to menu Ime This DVD receiver can display various data regarding the disc being played Press the DISP button for the following 1 Press once the number of titles and chapters in each title appears DISP 2 Press again the time of a selected title appears DISP MENU MENU PBC With the PBC function on choosing a song on a CD can only be done when at
12. other hazards Safety Check Upon completion of any service or repairs to this product askthe service technician to perform safety checks to determine that the product is in proper operating condition Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel TV System This unit is compatible with television sets featuring either the NTSC or PAL color system Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation and protection from overheating These openings should never be blocked by placing the product on a bed sofa rug or other similar surface This product should not be placed in a built in install ation such as a bookcase or rackunless proper ventilation is provided Never place this product near a heat source such as heat registers stoves radiators or any other product that produces heat Water and Moisture Do not use this product near sources of water and moisture such as bath tub wash bowl kitchen sink or wash machine in a wet damp basement or near a swimming pool or similar locations If moisture condensation occurs remove any disc connect the unit s power cord to a wall outlet turn the unit on and leave it on for two to three hours By then the unit will have warmed up and evaporated any moisture e
13. CM settings Prologic settings Prologic This unit features an integrated Dolby Prologic decoder that can give youa virtual Surround sound experience When the disc has stopped press SETUP Select and press ENTER Select Prologic and press ENTER Select the desired Prologic setting and press enter com OFF Default The Dolby Prologic decoding function will always be deactivated ON Dolby Prologic will always be activated E Press SETUP to save and exit the setup menu Subwoofer settings Prologic Subwoofer Test Tone DRC LPCM kam Off In the setup menu it must be indicated whether a subwoofer is connected to the system or not indicated by the figure 1 in 5 1 A When the disc has stopped press SETUP B Select More Audio and press ENTER C Select Subwoofer and press ENTER D Select the desired subwoofer setting and press ENTER ON Default A passive or an active subwoofer is connected Prologic n to the unit for reproduction of LFE Low Frequency Effect Subwoofer E signals Test Tone e Oft OFF No subwoofer is connected to the unit Quem 96k E Press SETUP to save and exit the setup menu Testtone settings The test tone can manually be set to right front speaker left front speaker center speaker right rear and left rear speakers ee o A When the disc has stopped press SETUP Ge A HE B Select More Audio and press ENTER Test Tone ot Center C
14. NER button to select desired wave band AM or FM 2 Press UP or DOWN button to find a station The freguency will change with each press When a station s signalis received it will appear in the display 3 70 lock onto a station quickly hold the UP or DOWN button for two seconds The unit will start automatic tuning When a station is found automatic tuning stops 4 To add a station to memory press the MEMO button The memory storage number will blink for four seconds in the display Press MEMO again to store the station Memory number A Wave band Station frequency 5 Toreduce noise when an FM stereo program has been received press the MONO button The word STEREO will disappear from the display The program is now heard in monographic form reducing the noise To resume stereo play press the MONO button again Automatic Tuning This unit will store up to 50 individual AM or 50 individual FM radio stations in its memory 1 Press the gt gt button The word AUTO will appear in the display and the automatic tuning mode is activated 2 Stations will be storedin ascending order until 50 stations of that particular wave band have been saved When a station is stored the memory storage number as well as the station s freguency will flash for four seconds in thedisplay 3 When the total number of stations reaches 50 ina particular wave s AM or FM memory no further stat
15. Y key again and the total remaining time for that particular chapter appears CHAPTER REMAIN DO 070 36 5 Press the DISPLAY key again and the display turns off EI N P This DVD receiver supports video output of various systems including auto NTSC and PAL The picture will blink and become colourless when the wrong system is selected NTSC for North America PAL for Europe For more information on output format referto the TV set s manufacturer s instructions Subtitles The unit has the capability to display subtitles in any of 32 different languages 1 Press the SUBTITLE key The subtitle menu will appear Selectthe desired language by pressing the SUBTITLE key SUBTITLE 02 08 ENGI SUBTITLE g 2 To remove the subtitles from view press the SUBTITLE key until they disappear Note The disc being played must be multi subtitle encoded Camera Angle The ability to change the camera angle allows viewer to play director and watch a movie from different perspectives 1 Press the ANGLE key on the remote control With each press the camera angle changes 2 The key may be pressed only when the flashing angle icon appears in the unit s display panel Note Camera angle may be changed only in discs with multi angle capability encoded into them Language The unit has the capability to show movies in one of eight languages 1 Press the AUDIO key The language
16. a widescreen TV Note Not all DVD discs offers all these formats If a formatis not available the disc will overwrite your TV Shape settings and show the movie in the available format Select TV system in the setup menu and press ENTER orD to view the TV system submenu TV Shape 4 3 PS TVSystem SON mee Video Output S Video PAL Press CL to change your selection A Press ENTER to confirm your selection Press SETUP to exit the setup menu AUTO B NTSC Select this if a NTSC signal is required to match the settings on your TV set PAL Selectthisifa PAL signal is required to match the settings on your TV set AUTO Select this if your TV set can transmit both NTSC and PAL signals Select Video Output and press ENTER or D to view the Video Out submenu A Press ENTER to confirm your selection TV Shape 4 3 PS B Press SETUP to exit the setup menu TV System NTSC Video Output S video ES Note Composite video outputs are always available S Video Select this if the unit is connected to your TV set through an S Video cable RGB Select this if the unit is connected to your TV set through a Scart cable Press 1710 to change your selection Audi o Setup The Audio menu allows you to set analog and digital audio outputs to match any external units For instance If your unitis connected to a TV set through the analog stereo outputs you must set the analog output
17. ad wall outlets exten sion cords or integral convenience receptacles as this may result in a fire or electric shock Power Cord Protection Power supply cords should be routed so that they are not likely tobe walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles andthe point where they exit from the product Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal Power Sources This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company For products intended to operate from battery power or other sources refer to the operating instructions This DVD home theater operates on 230V AC 50Hz Do not turn off unit immediately after turning on wait at least 10 seconds Replacement Parts If replacement parts are reguired be sure the service technician has used replacement parts specified by or have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or
18. ay will close The disc type will appearin the upper left hand corner of the screen Once it has read the disc the unit automati cally will begin playback When playing a DVD the DVD title or menu will appear CD tracks are played in sequence Note e Itis possible to damage a disc if it is not placed correctly on the guides in the disc tray This may also cause the DVD player to malfunction Do not force or place anything other than a 5 DVD or CD onto the disc tray e Never move the DVD player during playback as this may cause damage to the disc as well as the player To open and close the disc tray only use the OPEN CLOSE key found on both the remote control and on the unit s front panel PLAY REMOTE CONTROL D p PLAY FRONT PANEL m g Press PAUSE key PAUSE If REMOTE contro O II PAUSE FRONT Ug 5 PREV NEXT playback Press I key or Ikey play previous or next track To resume normal playback press PLAY key Press PREV key REMOTE CONTROL I g Press NEXT key REMOTE CONTROL M g 6 Fast Forward Reverse Playback The unitfeatures both fast forward and fast reverse playback Either mode will speed up 2x 4x 8x 16x To activate either function simply press the b gt key or 4 key on the remote control The speed changes each timethe key is pressed To resume normal playback press the PLAY key Memory Playback This unit allows the viewer to s
19. cause damage to the equipment have been properly completed e Do not tie the AV cord with any other cords such as the power cord or speaker wires as it may result in poor picture and or sound quality 10 The configuration and arrangement of a surround sound system s speakers is critical For maximum listening enjoyment refer to the Arrangement of Speakers section in this manual prior to connecting speakers Surround Sound Speakers Frontor main right and left speakers center speaker e These three speakers provide extensive sound imaging and augment the dynamic effect of the audio A movie s principal dialogue comes through these speakers Rear or surround sound speakers e These two speakers provide 3 D dynamic sound effects and create an enveloping atmosphere as they add background sounds Subwoofer speaker e Provides rich and powerful bass adding a powerful dimension of realism Note Audio recorded for the center speaker and subwoofer will be assigned to the front and 3 D rear speakers to obtain the optimum 3 D surround sound effect The ideal surround sound speaker configur ation may vary according to room size and wall material The figure below illustrates a typical arrangement Hints e Front or main speakers and central speaker should be placed at the same level and in a way that sound is oriented toward the listener s ears e 3D surround sound or rear speakers should be placed 3 higher t
20. ce may occur e Placing an object on the remote control may cause it to inadvertently depressa button changing a function and shortening battery life e Do not glaze the front of the DVD receiver with colored glass as it may cause interference with normal operation of the controller e Make sure there is no barrier between the remote control and remote sensor as it could prevent the unit from receiving the signal e Donot spill water or put wetitems on the remote control e Never disassemble remote control BATTERIES INCORRECTUSE OF BATTERIES MAY CAUSE THEM TOLEAK CORRODE OR EXP LODE CD 0000 A SPEAKERS IMPEDANCE 61 m tot kot t ok D Active Subwoofer Optional af RECORDER e Connection terminals for this DVD receiver e Red terminal marked R is for connecting the are found onthe rear panel Read carefully right channel The white terminal marked L and follow the manufacturers instructions is for connecting the left channel The yellow of any video and audio device being terminal is for video connection Make sure connected to this unit all connections are securely made Improper connections may cause noise poor perfor e Do notconnect the power until all connections mance or
21. ctions O HOME THEATRE SYSTEM e 1 POWER All connections must be checked before the mains plug is inserted into the socket Then insert the mains plug carefully into the socket Press the POWER button on the front panel to turn on the unit When the power is turned on for the first time a short surge may disrupt the function of other electronic eguipment in the same circuit If so connect the unit to a wall socket of another circuit 2 OPEN CLOSE This button is used to open and close the DVD tray 3 PLAY PAUSE AUTO This button is used to start and pause playback in DVD mode When the unit is in TUNER mode the button can be used to initiate an automatic channel search Back Panel Functions 1 ANTENNA For connection of the supplied AM and FM antennas 2 AUX IN For connection of external accessory eguipment such as a CD player 3 AUDIO OUT For connection of an external amplifier if you wish to hear the sound in another room VIDEO OUTPUT S VIDEO OUTPUT REAR For connection of rear speakers aur 4 PREV DOWN This button is used to select the previous track when the unit is in DVD mode In TUNER mode it can be used to initiate a manual search at lower frequencies 5 NEXT UP This button is used to select the next track when the unit is in DVD mode In TUNER mode it can be used to initiate a manual search at higher frequencies
22. eliminates the use of an external power amplifier LASER HEAD OVER CURRENT PROTECTION SYSTEM To extend the service life of thelaserhead the unit includes a unigue laser head over current protection system ensuring a constant laser current Wu This page contains valuable information regarding the handling cleaning and storage of discs played in this unit Handling e Do nottouch the playback side of the disc e Do not attach paper or tape to discs e Do not stick or write anything on the surface Protect against fingerprints e Always hold a disc by the center and edge portions Cleaning e Fingerprints and dirt on the disc may cause picture and or sound deterioration Wipe the disc from the center outward with a soft cloth Always keep the disc clean e f you cannot wipe the dirt off lightly use a slightly moistened soft cloth and finish with a dry cloth e Do not use any type of solvent such as Paint thinner benzene commercially available cleaners or anti static spray for vinyl LPs Storing e Do not store discs in places subject to direct sunlight or near heat sources e Do not store discs in places subject to moisture and dust e Store discs vertically in a case Stacking or placing objects on discs outside of their case may cause warping NOTE Is not responsible for damage that may occur to any disc that is operated in this unit or not handled cleaned or stored as suggested above y Front Panel Fun
23. eltax just play Instruction Manual DDD Cinema DVD Home Theatre System Vision DVD Home Theatre System END A lightning bolt with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alertthe user to the presence of important operating and main tenance servicing instructions in the literature accompanying the appliance WARNING TO AVOID THE DANGER OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE NEVER OPEN THE CABINET AS DANGEROUS HIGH VOLTAGES ARE CONTAINED INSIDE ONLY A QUALIFIED SERVICE TECHNICIAN SHOULD ATTEMPT TO OPEN THE CABINET CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT INTO ELECTRICAL SOCKET CAUTION This DVD receiver unit employs a laser system To prevent direct exposure to the laser beam do not open the enclosure Visible laser radiation is present when enclo sure is open DO NOT STARE INTO BEAM Additionally the use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radia tion exposure To ensure proper use of this product please read this owner s manual carefully and retain for future
24. enlarges it1 3x a sixth press enlarges it1 4x To return to normal size playback press the ZOOM key aseventh time Enlargement takes place in the center of the picture Volume and Mute The volume on this DVD receiveris easily controlled with the remote control by pressing either the VOL key to raise the volume or the VOL key to lower it By pressing the MUTE key no audio will be heard To reinstate the audio press the MUTE key again With the unit in DVD mode and stopped press SETUP and the following setup menu will appear on the TV screen Program Allows you to program specific tracks ina desired order of play Press PROG key and program menu will appear on the screen set up the program play in number key Then scroll to START Press ENTER key to program play To exit the Programmed play mode press the PROG button again DVD Menu Setup By pressing the SETUP key on the remote control the main setup menu appears 1 After accessing the setup menu press the scroll key for up or down movementto selecta desired item Once anitemis selected press the PLAY key to confirm your entry and to move to the Sub entry 2 Use the left or right scroll key to move the pointer and the up or down scroll key to select the Desired option Once an item is selected press the ENTER key to confirm your selection This completes the setup of the selected function Press GD item A Press ENTER to activate a submenu B P
25. han the height of listener s ears e Subwoofer speaker may be placed anywhere within the room asits location produces little effecton a listener s sensation to sound To obtain the optimum bass effect a subwoofer is recommended in home theater systems H 6 1 TV set or screen 2 Front or main left speaker 3 Subwoofer 4 Center speaker 5 Front or main right speaker 6 3 D surround sound left speaker 7 3 D surround sound right speaker 8 Viewer s location mm This well designed DVD receiver provides Connecting Speaker Cables optimum sound quality when the speakers used are within the range of their rated impedance 1 Peeloff approximately 1 2 of cable insulation 2 Tighten the wire end 2 below Important 3 Open cable terminal by pressing back on e The minimum impedance of the five speaker tab terminals is 4 ohm forthe subwoofer it is 4 Insert wire end into terminal 8 ohm 5 Release tab make sure wire is in terminal securely e If you wantto use only one speaker or listen to monophonic music do not parallel connect Note To prevent damage to the circuit care individual speakers to the left and right should be taken to prevent short circuiting from channel terminals See the figure on the left occurring atthe positive and negative poles of below the speaker cord 1 2 m OHO p Ww 4 5 SS KE A
26. hange your selection Note Audio languages may vary from disc to disc A Press ENTER to confirm your selection B Press SETUP to exitthe setup menu Select DVD menu Menu language in the setup menu and press ENTER or D to view the DVD menu submenu Subtitle Audio DVD Menu English English German French Spanish Presst to change your selection Note Menu languages may vary from disc to disc WW A Press ENTER to confirm your selection B Press SETUP to exitthe setup menu Video setup Select Video in the setup menu and press ENTER to view the Video submenu Press gu to Press ENTER or D to select one of the select menu item TVShape MEN options l b TV System NTSC Press lt Jto go back one item Video Output S Video Press 1 or repeatedly to return to the setup menu Select TV Shape in the setup menu and press ENTER or D to view the TV Shape submenu TV Shape EMI Press Qg to change your selection TV System NTSC 4 31B A Press ENTER to confirm your selection Video Output S Video 16 9 en B Press SETUP to exitthe setup menu X d 4 3 PS Pan and Scan refer to pictures where parts of the picture have been cut off to fit the entire screen 4 3 LB Letter Box refers to pictures where a black bar is visible at the top and at the bottom of the screen 16 9 Refers to a picture that fills up the entire screen of
27. ion in that wave band will be saved To Play Preset Stations 1 Press the TUNER button to select the desired wave band 2 Press the PRE TUN button 3 Press any of the numbered buttons to select the desired station s memory number For example to play the station at memory 5 simply press the 5 button for memory 17 press the 1 button followed by the 7 button 4 Stations in the memory function may also be accessed by pressing the UP or DOWN button Te n Once the unitis connected to a television set and any other accessory equipment you are ready to enjoy the excitement of DVD videos or your favorite CDs and MP3 files To play a DVD video disc Turn on the TV and select the A V mode If the set features an SCART connection be sure the SCART mode is selected from the TV menu Turn on amplifier if connected Select AC 3 or DVD mode To play an audio disc Turnonthe audio system and choose the input source that is connected to the DVD player Set the SPDIF OUTPUT to SPDIF OFF from the SETUP MENU display if you don t have the proper equipment for Dolby Digital surround sound 1 Press the POWER key on front panel DISC LOADING appears on screen O POWER 2 Press the OPEN CLOSE key The disc tray will open OPEN CLOSE FRONT PANEL OPEN CLOSE REMOTE CONTROL D 3 Place the disc on the disc tray Be sure play side is face down on the tray 4 Press OPEN CLOSE key to close tray The disc tr
28. nel PCM PCM B Select Audio and press ENTER MP3 WMA OI eR C Select MP3 and press ENTER Others 5 1 channel PCM 54 channel D Set Digital out to 2 channel PCM default For transmitting a 2 channel stereo Off signal through the digital outputs Optical Coaxial to e g aminidisc or a CD recorder Off For deactivation of the digital outputs E Press SETUP to save and exit the setup menu Analog Out Digital Out Others Others m AC3 5 1 SSES PCM PCM Follow these instructions to set the analog and digital MP3 WMA 51 channel PCM nu output signals when you wish to play other audio tracks Others mu A Whenthe disc has stopped press SETUP 5 1 channel B Select Audio and press ENTER ee C Select Others and press ENTER lt J D SetAnalog Out to 5 1 Channel Default For Dolby Digital playback in the original format i e sound through all outputs 2 Channel For downmixing of a 5 1 signal i e stereo sound E Set Digital Out to PCM Default For transmitting a 2 channel stereo signal through the digital outputs Optical Coaxial to e g a minidisc or a CD recorder RAW For transmitting the raw 5 1 channel digital bitstream signal through the digital outputs Optical Coaxial to e g an external digital surround receiver Off For deactivation of the digital outputs F Press SETUP to save and exit the setup menu More Audio Setup In the More Audio menu the following settings can be made Subwoofer Test Tone DRC and LP
29. neven surfaces may cause the product and cart combination to overturn Attachments Use only attachment srecommend ed by as they may cause hazards Cleaning Always unplug this unitfrom the wall electrical outlet before cleaning Do not use liquid or aerosol cleaners use a damp cloth for cleaning Lightning For added product protection during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and or disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges Object and Liguid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could resultin a fire or electric shock Never spill liguid of any kind on or into the product Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded so as to provide protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides information with regard to proper grounding of the mast and sup porting structure grounding of the lead in wire to an antenna discharge unit size or grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode Overloading Do not overlo
30. reference Should the unit require maintenance contact an authorized service location or contact PROTECT YOURSELF Record the model and serial numbers for this unit while it is easy to see them These numbers are located on the back of the unit s cabinet Retain this information for future reference ModelNo Cinema Vision Serial No Retain this information for future reference WARNING A RISK OF ELECTRICSHOCK A DO NOT OPEN CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK THERE IS NO USER SERVICE ABLE PART INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL EI CAUTION Is it important that you read and follow all of the instructions in this booklet and any marked on the unit itself Retain this booklet for future reference Accessories Never place this product on an unstable platform stand cart wall mount shelf or table The product may fall causing serious personal injury to persons and pets as well as seriously damaging the product Use only with a stable platform stand cart wall mount shelf or table that has been recommended by or sold withthe product Any mounting of the product should follow the manufacturer s instructions and use a mounting accessory recommended by the manufacturer This unit while positioned on some type of cart must be moved with care Quick stops excessive force and u
31. ress SETUP to exit the setup menu to go to the next Setup Menu Language Setup Select Language in the setup menu and press ENTER to view the Language submenu r i OSD Menu Susi Press 430 to Subtitle English select menu item Audio English L DVDMenu English A Press ENTER or D to select B Press 1to go back one menu item C Press lt or Q repeatedly to return to the setup menu 20 y Language Setup Select OSD Menu in the setup menu and press ENTER or 5to view the OSD Menu submenu OSD Menu Subtitle Audio DVD Menu English Deutsch English Francais English Espanol pre Press O to change your selection A Press ENTER toconfirm your selection B Press SETUP to exit the setup menu Select Subtitle in the setup menu and press ENTER or p gt to view the Subtitle submenu the Audio submenu OSD Menu Subtitle Audio DVD Menu OSD Menu Subtitle Audio DVD Menu English English English fs i English German i French English Spanish Auto Off English English English German French i Spanish i Press 7 O to change your selection Note Subtitle languages may vary from disc to disc A Press ENTER to confirm your selection B Press SETUP to exit the setup menu Select Audio Syncronisation in the setup menu and press ENTER or D to view Press OG to c
32. s to 2 Channel to be able to enjoy the sound in downmixed stereo You can setthe audio formatindividually for each ofthe following inputs Dolby Digital Mp3 CD and Others You muststop DVD playbackto be able to make changes in the setup menu Dolby Digital settings Follow these instructions to set the analog and digital audio output formats for Dolby Digital sound A When the DVD has stopped press SETUP B Select Audio and press ENTER C Select Ac3 and press ENTER D Set Analog Out to zs 5 1 Channel Default For Dolby Digital playback in the mi Duo original format i e sound through all outputs 5 1 chahnel PCM Off 2 Channel For downmixing of a 5 1 signal i e Stereo 5 1 channel PCM sound 5 1 channel E Set Digital Out to 2 channel PCM Default For transmitting a 2 channel stereo signal through the digital outputs Optical Coaxial to e g a minidisc or a CD recorder RAW For transmitting the raw 5 1 channel digital bitstream signal through the digital outputs Optical Coaxial to e g an external digital surround receiver Off For deactivation of the digital outputs F Press SETUP to save and exit the setup menu Ep MP3 WMA settings Follow these instructions to set the digital output signal when you wish to play Mp3 tracks Note The analog formatis locked to stereo N 23 Analog Out Digital Out A When the disc has stopped press SETUP Ac3 5 1 chan
33. the main menu With the PBC function off song selections can be made by entering the relevant number keys The menu content ofthe disc will appear when the MENU button is pressed while a DVD disc is playing AUDIO IBTITLE MENU pa y Repeat Play This DVD receiver allows repeated playback of specific titles chapters tracks or segment It even allows switching between two items that are being repeated 1 Select the item to repeat 2 Press the REPEAT key The repeat mode changes each time the REPEAT key is pressed i e from title repeat to chapter repeat all repeat to repeat off MP Volume up down Adjustment ress the CH SEL button on the remote control TV OSD appears VOL L 00db Press CH SEL twice OSD Appears VOL R 00db Press CH SEL thrice to seven times the OSD converts in turn of RF LS RS CN and SW VOL RS 00db VOL LS 00db VOL C 00db VOL SW 00db Press CH SEL continually it goes in cycle Press the VOL or VOL button on the remote control to change the Volume value of ALL LF RF LS RS CN or SW separately MONO CH SEL 5 93 Zoom A picture may be enlarged up to fourtimes during either playback or slow motion through the unit s zoom function Press the ZOOM key once and it enlarges the image 2x pressa second time and the image enlarges 3x A third press enlarges the image 4x A forth press enlarges the image 1 2x a fifth press
34. top playback then later continue playback from that exact disc location Pressthe STOP keyto halt playback The unitthen will memorize the location where playback was stopped To resume watching press the PLAY key and the unit will resume playback from the exact location where playback was stopped Exclude Mp3 DISC When you play DVD discs press MENU or TITLE key return menu and title the unit then will memorize the location To resume watching press the PLAY key and the unit will resume playback from the exact location low Motion This DVD receiver has the ability to play discs in slow motion in either forward or reverse direction Each time the SLOW key is pressed the speed will slow from forward slow speed1 2 to 1 4 to 1 8 to 1 16 to reverse slow speed 1 2 to 1 4 to1 8 to1 16 to normal speed To resume normal playback press the PLAY key Screen Display _ While a disc is playing the status of various functions may be checked such as the tile track number and several time categories 1 Press the DISPLAY key once and the title appears along with the chapter and how much time has played TT 01 02 CH 02 28 m 00 21 05 2 Press the DISPLAY key again and the remaining time for that particular title appears TITLE REMAIN 010 44 34 3 Press the DISPLAY key again and the total elapsed time for that particular chapter appears CHAPTER ELAPSED oog ren 29 4 Press the DISPLA
35. u to start where you stopped the movie last time LOAD Factory downloads the pre programmed factory settings Note All the settings you have made will be deleted Mp3 is an audio compression method that applies level 3 of the international MPEG standard whereby a sound signal is compressedat the ratio of 12 1 It means that an Mp3 disc may contain up to 600 minutes of music or up to 170 tracks depending on the sound quality How to play an MP3 disc MP3 file menus When you play an Mp3 disc two to playback modes can be selected FILE LIST and PROGRAM 1 FILE LIST A list of the tracks on the disc will be displayed You mark them by moving the marking bar by means of the arrow keys and select them by pressing ENTER 2 PROGRAM Press the PROG key An empty list will be displayed where you can fillin the desired tracks by Means of the number keys Finally press the PLAY key I JPEG is a compressed picture format used for picture storage Even if pictures are compressed up to 15 20 times their quality remains outstanding JPEG files are ideal for storing of pictures as they are supported by most types of software for picture processing contain small data and are easy to use This DVD player can read pictures in JPEG format on CD discs Press the relevant number key to select photo display 1 Insert the disc correctly then the machine will start searching for disc information 2 Press a number key to select
Download Pdf Manuals
Related Search