Electrolux 44070 VI Dishwasher User Manual
Contents
1. Operating Instructions Pull the upper basket out completely Holding the upper basket at the rear Adjusting the Height of the Upper Basket Maximum Height of the Dishes in the Upper Basket Lower Basket With upper basket raised 22 cm 31 cm With upper basket lowered 24 cm 29 cm The height of the basket can also be adjusted when it is loaded Lowering the Upper Basket Pull the upper basket out completely Holding the upper basket at the rear right lift it as far as it will go and then lower it vertically The upper basket will engage in the lower posi tion Raising the Upper Basket right lift it as far as it will go and then lower it vertically The upper basket will engage in the higher posi tion 23 Operating Instructions 24 Filling with Detergent I 1 Only use dishwasher detergent Fill with detergent Prior to the start of a wash programme not for the pre wash pro gramme The detergent is released into the wash water during the programme Please observe the manufacturer s dosing and storage recommenda tions as stated on the detergent packaging The detergent compartment is on the inside of the dishwasher door If the lid is closed press release button 1 The lid springs open Fill the detergent dispenser with detergent The markings indicate the dosing levels 20 corresponds to approx 20 ml of detergent 30 corresponds to2. looo IIAN QOO 000090 O O00 O00000 000 2000000 00000022 Your dishwasher has one of the following four types of lower basket Type 1 The right hand plate inserts in the lower basket can be folded across one another To ease the loading of large items the two right hand plate inserts in the lower basket can be folded across one another Type 2 The two rear plate inserts in the lower basket can be folded across one another To ease the loading of large items the two rear plate inserts in the lower baskets can be folded across one another 7 Ge a fo A A p o 0 p ZZZV TTT TTT VTS TTT 0 7 F D 0 0 0 r 0 p o 21 Operating Instructions 22 Loading Cups Glasses and Coffee Services Load small delicate items and long pointed cutlery in the upper basket e Arrange items of crockery on the folding cups racks so that they are offset from each other and water can reach all items e The cup racks can be folded up out of the way for tall items e Lay or hang wine champagne and brandy glasses in the cut outs on the cup racks e Glasses beakers etc can also be placed on the two rows of prongs on the left of the upper basket
3. 2 eee eee eee 5 Safety Instructions sisii ia a eens 5 Disposals coan get awie a DATES eS Lie oan EGA SEE wee Os 7 Economical and Ecological Dishwashing 7 Appliance Features Display and Control Panel 8 Display and control panel ees 9 Prior to using for the first time 0 cece eee eee 9 Water SOftEN r cscacsicinecigandnoy ga a eed eae bauer eed odes 10 Setting the water softener 2 0 cece eee eee ee 11 Special salt for the water softener 0000 e eee eee eee eee eee 12 Setting the amount of special salt to be added 12 Adding special salt 2 00 13 RINSE ald ve tty ihe el bi dae Eh ade ate bbs aoe 14 Activating deactivating the inflow of rinse aid 00005 14 Adding rinse aid 1 1 nais eraai aa a E a 16 Adjusting Rinse Aid Dosing 00 cece eects 17 Activating deactivating the acoustic signal 00 e eee eee 18 In Daly Use yt tsais eee eon sack E E av tcee nee wads Waece aednastetdo a a pndcevanesnealy atcats 18 Loading Cutlery and Dishes eee eee eee eee eee 19 Loading Cutlery 2 0 eee eee teenies 20 Loading Pans Frying Pans and Large Plates 21 Loading Cups Glasses and Coffee Services 2200000000es 22 Adjusting the Height of the Upper Basket 00005 23 Filling with Detergent iaasa ea Saeed ade Wire are a aes 24 Use of 3 in 1 Co
4. Organisation is aware of your move and able to look after you and your appliances France Senlis 33 0 3 44 62 29 29 Germany N rnberg 49 0 800 234 7378 Italy Pordenone 39 0 800 117511 Sweden Stockholm 46 0 8 672 5360 UK Slough 44 0 1753 219899 45 46 Service and Spare parts SERVICE AND SPARE PARTS In the event of your appliance requiring service or if you wish to pur chase spare parts please contact Service Force by telephoning 08705 929 929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area For the address of your local Service Force Centre and further informa tion about Service Force please visit the website at www serviceforce co uk Before calling out an engineer please ensure you have read the details under the heading What to do if When you contact the Service Force Centre you will need to give the following details 1 Your name address and post code 2 Your telephone number 3 Clear and concise details of the fault 4 The model and serial number of the appliance found on the rat ing plate 5 The purchase date Please note that a valid purchase receipt or guarantee documentation is required for in guarantee service calls Customer Care For general enquiries concerning your AEG appliance or for further information on AEG products please contact our Customer Care Department by letter or telepho
5. stances 31 Operating Instructions 32 What to do if Try to rectify minor faults on the dishwasher with the aid of the instructions given here If you call an engineer to resolve a of fault listed here or to repair a fault caused by incorrect use or installation a charge will be made even if the appliance is in guarantee Error messages are displayed i If your appliance is equipped with an optical floor signal in the event of an error a dot shaped optical signal will flash on the floor Errors will only be indicated acoustically if the acoustic signal has been activated If as listed in the table below any of the indicators in the control panel or the display panel are flashing or are illuminated and or if an acous tic signal can be heard you can probably rectify the fault yourself Malfunction Possible cause Remedy The tap is blocked or furred with lime scale Cean tap The tap is turned off Turn the tap on The filter where present in the One continuously repeated threaded hose fitting at warning tone can be heard the water inlet valve is the cycle indicator for the blocked selected cycle is flashing the end cycle indicator is flashing once repeatedly There is no water running Filters in the base of into the dishwasher the washing compart ment are blocked Clean the filter in the threaded hose fitting Press the button for the commenced dishwashing cycle then c
6. a premium will be charged Exclusions This guarantee does not cover e Damage or calls resulting from transportation improper use or neglect the replace ment of any light bulbs or removable parts of glass or plastic e Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom e Appliances found to be in use within a commercial environment plus those which are subject to rental agreements e Products of AEG manufacture which are not marketed by AEG European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications e The guarantee starts from the date you first purchased your product e The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products e This guarantee relates to you and cannot be transferred to another user e Your new home is within the European Community EC or European Free Trade Area e The product is installed and used in accordance with our instructions and is only used domestically i e a normal household e The product is installed taking into account regulations in your new country Before you move please contact your nearest Customer Care centre listed below to give them details of your new home They will then ensure that the local Service
7. approx 30 ml of detergent Close the lid and press until it locks into place If the dishes are very heavily soiled put additional detergent into the adjacent chamber 2 This detergent will take effect during the pre wash gt D W Operating Instructions is 1 Use of 3 in 1 Combi Detergent Tablets General Advice These products are tablets with combined detergent rinse aid and salt functions Before using these products you should first check that the water hard ness in your supply is compatible with the use of these products as per the detergent manufacturers instructions on the product packaging These products should be strictly used according to the detergent manufacturers instructions Do not place the tablets in the tub or the cutlery basket as this will result in poorer wash results The tablets should be placed in the detergent doser If you encounter problems when using 3 in1 products for the first time then please contact the detergent manufacturers care line the telephone number is given on the product packaging Special Advice When using combination products the rinse aid and salt lights are no longer useful It may be helpful therefore to switch the rinse aid off please note that only some dishwashers have this facility and selec ting the lowest possible setting for water hardness For more information please refer to your instr
8. bladed knives stored in an upright position are a potential haz ard e Long and or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket e When finished loading or unloading close the door as an open door can be a hazard Correct Use e Only wash household dishes using the dishwasher If the appliance is used for other purposes or is used incorrectly the manufacturer can not accept any liability for any damage caused e Only use detergents specifically designed for use in domestic dish washers e Do not put any solvents in the dishwasher There is a risk of an explo sion e The anti flood system provides dependable protection against dam age due to leaks For this system to function correctly the following preconditions must be met The appliance must remain connected to the mains even when it is switched off The dishwasher must be correctly installed Always shut off the water supply at the tap when the dishwasher is not to be used for longer periods e g when you are away on holiday e Do not sit or stand on the open door the appliance may tip over Operating Instructions e In the event of a fault first close the tap then switch off the appli ance and unplug it from the mains If the appliance is permanently wired to the mains remove the fuse Disposal Disposing of the Packaging Material Dispose of the dishwasher packaging material correctly A
9. into place cloth Otherwise too much foam will be formed during the wash Operating Instructions i Open the door of the dishwasher Press the rinse aid compartment Fully open the rinse aid compartment Set the dose level Close the lid and press until it locks If rinse aid has spilt wipe up with a Adjusting Rinse Aid Dosing As the dishes are washed rinse aid is released from the dispenser into the wash water The dose is factory set at 4 and can be adjusted from 1 to 6 Only change the setting if streaks milky spots or dried on water marks are visible on glasses or crockery release button with your finger lid into place cloth 17 Operating Instructions Activating deactivating the acoustic signal 3 The acoustic signal can indicate acoustically at which water hardness the water softener is set when a dishwashing cycle has finished when an error has occurred with the dishwasher You can switch on off the acoustic signal in the following way Press the ON OFF button The LED indicators for all programme buttons and the button for the delay start timer if present light up The LED indicators and any option buttons that are present only light up if they are activated If the only LED indicator illuminated is one that belongs to a pro gramme button this means that this dishwashing cycle has been acti vated The dishwashing cy
10. through the funnel the capacity of the con tainer is approx 1 0 1 5 kg depend ing on the grain size Do not overfill the salt container with salt il The water expelled by filling the salt container with salt runs out of the salt container onto the base of the washing compartment This is not a cause for concern the water will be pumped out at the start of the next wash programme 5 Clean any salt remnants on the container opening 13 Operating Instructions il 6 Turn the lid clockwise to the stop otherwise dishwasher salt will leak into the wash water this could lead to poor wash results To avoid this run a rinse programme after filling the salt container with special salt This will wash away salt water and any salt crystals that have been spilt Depending on the size of the salt grains it can take several hours for the salt to dissolve in the water and the special salt indicator S to extinguish The setting of the water softener and the consumption of salt are dependent on the hardness of the local water Rinse aid Rinse aid ensures that your dishes gleam and are free from spots and that your glasses are clear Rinse aid can be added in one of two ways e f you are using dishwasher detergent that already contains rinse aid the detergent including the rinse aid is put into the detergent com partment In this case the dispensing of rinse aid from the supply container must be dea
11. 3 4 inch The inlet hose is equipped either with a plastic or with a metal connection nut Tighten plastic hose connection nuts by hand only Metal hose connection nuts must be tightened using an appropriate tool Finally visually check that it is water tight ensure that the tap is not dripping e In order that access to the tap in the kitchen is not limited by the use of the dishwasher we recommend the installation of an additional tap or fitting a two way adapter to the existing tap e If you need a longer water inlet hose than that supplied VDE approved complete hose sets are to be used These are available from your local Service Force Centre e Do not use for connection old hoses which have been used for another appliance Installation and Connection Instructions The following section is only applicable to dishwashers that have a safety valve on the threaded hose fitting for the tap Water inlet hose with safety valve After connecting the double walled water inlet hose the safety valve is next to the tap Therefore the water inlet hose is only under pressure while the water is running If the water inlet hose starts to leak during this operation the safety valve cuts off the running water and the draining pump in the dishwasher is switched on Please take care when installing the water inlet hose The electrical cable for the safety valve is in the double walled water inlet hose Do not immerse the water i
12. FAVORIT 44070 VI Fully Integrated Dishwasher User Instructions AN Is i Gy Dear customer Please read these user instructions carefully Please observe the safety instructions on the first few pages of these user instructions Please keep these user instructions for later reference Pass them on to any subsequent owner of the appliance The warning triangle and or specific words Warning Caution Important are used to highlight instructions that are important for your safety or for the function of the appliance It is imperative that these instructions are observed This symbol or numbered instruction steps lead you step by step through the operation of the appliance Next to this symbol you receive additional information and practical tips on using the appliance Tips and instructions for the economical and environmentally conscious use of the appliance are marked with a clover leaf In the event of a malfunction these operating instructions contain information on how to rectify faults yourself see the What to do if section If these instructions are insufficient please contact your AEG Service Force Centre In this respect please read the chapter Service amp Spare Parts Printed on paper manufactured with environmentally sound processes He who thinks ecologically acts accordingly Contents CONTENTS Operating Instructions
13. aid container have been filled with salt and rinse aid respectively and using the test programme see Programme Table Full Load Half Load 12 place settings 6 place settings incl serving dishes incl serving dishes leaving alternate positions free Detergent Dosing 5g 25g Type B 20g Type B Rinse Aid Setting 4 Type III 4 Type III Sample loading arrangements Upper basket HF nnn H H AQ LALALALA If necessary move the cup rest from right to left When doing this ensure that the cup rest is at the same height Lower basket with cutlery basket Cutlery basket 9 IN NN AN WO Installation and Connection Instructions INSTALLATION AND CONNECTION INSTRUCTIONS Installing the Dishwasher Fitting the Furniture Door Panel i e The dishwasher must be installed on a firm floor and adjusted to ensure that it is stable and level e To compensate for unevenness in the floor and to match the height of the appliance to that of surrounding units extend the threaded feet by unscrew ing use a screwdriver e For built in integrated and fully inte grated dishwashers the rear feet should be adjusted from the front of the appliance using a screwdriver e The drain hose inlet hose and mains cable must not be kinked or crush
14. ancel the dishwashing cycle see chapter Starting a dishwashing cycle Clean out the filters See chapter Cleaning the filters Tne wear inlet inse nas Check hose installation not been correctly laid Operating Instructions Malfunction Possible cause Remedy Two short continuously The siphon is blocked Clean out siphon repeated warning tones can be heard the cycle indicator for the The water drain hose selected dishwashing cycle is has not been correctly Check hose installation flashing laid the end cycle indicator is flashing twice repeatedly Three short continuously repeated warning anes Turn off the tap and contact can be heard The leak prevention sys 5 na 3 your Local Service Force Cen the end cycle indicator is tem has been triggered i tre flashing three times repeat edly After rectifying the fault related to 1 or 2 warning tones press the button for the commenced dishwashing cycle The dishwashing cycle will continue If the fault is displayed again please contact your Local Service Force Centre For all other errors displayed please contact your Local Service Force Centre stating the error code 33 Operating Instructions there are problems with the operation of the dish washer Symptom The programme does not start Possible Cause The door of the dishwasher is not closed properly Mains plug is not plugged in House fuse is defective A start
15. ane ite estas S ee 40 Leak prevention system 0 cece eee 41 Electrical Connection lt ssic csgsonitwery Sdeele ea tar e a fad Gide a ea 42 CONNECTIONS E E E ee ete di hee as 43 Guarantee Conditions 0 cece eee eee eee 44 Service and Spare parts 0 0 ccc ce cece eee 47 Operating Instructions OPERATING INSTRUCTIONS N Safety Instructions The safety aspects of AEG electrical appliances comply with accepted technical standards and the German Appliance Safety Law Neverthe less as a manufacturer we consider it our obligation to make you aware of the following safety information Installation Connection and Placing into Operation e The dishwasher may only be transported upright e Check the dishwasher for transport damage Do not in any circum stances connect an appliance that is damaged In the case of damage please contact your retailer e Before installing the appliance ensure that the nominal voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed The fuse rating is also to be found on the rating plate e For information on how to correctly install and connect up your dish washer please read the Installation section Adaptors connectors and extension cables must not be used Child Safety e This appliance is designed to be operated by adults Children should not be allowed to tamper with the controls or play wi
16. ant Older cutlery with glued parts that is not temperature resistant Bonded cutlery items or dishes Pewter or copper items Lead crystal glass Steel items subject to rusting Wooden platters Items made from synthetic fibres are of limited suitability Only wash stoneware in the dishwasher if it is specifically marked as being dishwasher safe by the manufacturer Glazed patterns may fade if machine washed frequently Silver and aluminium parts have a tendency to discolour during washing Left overs e g egg white egg yolk and mustard often cause discolouring and staining on silver Therefore always clean left overs from silver immediately if it is not to be washed straight after use Some types of glass can become dull after a large number of washes Before loading the dishes you should Remove all scraps of food Soften remnants of burnt food in pans When loading the dishes and cutlery please note Dishes and cutlery must not impede the rotation of the spray arms Load hollow items such as cups glasses pans etc with the opening downwards so that water cannot collect in the container or a deep base Dishes and items of cutlery must not lie inside one another or cover each other To avoid damage to glasses they must not touch Do not lay small objects e g lids in the cutlery rack 19 Operating Instructions Loading Cutlery Long bladed knives stored in an upri
17. cle must be cancelled Press function buttons 2 and 3 simultaneously for approx 1 second The LED indicators for all programme buttons and the button for the delay start timer if present light up The LED indicators and any option buttons that are present only light up if they are activated Press function buttons 2 and 3 simultaneously and keep them pressed The LED indicators for function buttons 1 to 3 will flash Press function button 3 The LED indicator for function button 3 will flash The display will indicate the current setting The indicator is flashing Acoustic signal activated ex factory setting The indicator is not Acoustic signal deactivated flashing 4 Pressing function button 3 will change the setting Once the display is indicating the required setting press the ON OFF button The setting is now saved In Daily Use e Check the salt and rinse aid levels e Load cutlery and dishes into the dishwasher e Fill with dishwasher detergent e Select a wash programme suitable for the cutlery and dishes e Start the wash programme Operating Instructions Loading Cutlery and Dishes AN Sponges household cloths and any object that can absorb water should not be washed in the dishwasher For washing in the dishwasher the following cutlery dishes are not suitable Cutlery with wooden horn china or mother of pearl handles Plastic items that are not heat resist
18. ctivated to avoid a double dosage e f you are using dishwasher detergent and rinse aid separately the rinse aid is to be put into the rinse aid supply container In this case the dispensing of rinse aid from the supply container must be activated The amount of rinse aid to be dispensed must be set Use only branded rinse aid for dishwashers Never fill the rinse aid con tainer with any another substance e g concentrated vinegar or dish washer cleaning agent This would damage the appliance Activating deactivating the inflow of rinse aid Some appliances are equipped with an additional 3 in 1 function If you use 3 in 1 dishwashing tablets and select the 3 in 1 function together with the dishwashing cycle the inflow of rinse aid does not have to be deactivated see 3 in 1 function Operating Instructions 1 Press the ON OFF button The LED indicators for all programme buttons and the button for the delay start timer if present light up The LED indicators and any option buttons that are present only light up if they are activated If the only LED indicator illuminated is one that belongs to a pro gramme button this means that this dishwashing cycle has been acti vated The dishwashing cycle must be deselected Press function buttons 2 and 3 simultaneously for approx 1 second The LED indicators for all programme buttons and the button for the delay start timer if present light up The LED indicators and an
19. d scale deposits on the dishes and in the dishwasher the dishes must be washed with soft water i e water with a low lime content The dishwasher therefore has a built in water softener in which tap water with a hardness of 4 d German degree and harder is softened with the aid of special salt il Your water supplier will be able to inform you about the hardness and hardness range of the water in your area The water softener can be set manually using the water hardness switch it can also be set electronically using the buttons on the control panel Adjusting the hardness z Number of setting flashes and Water hardness wag 1 In d Inmmol l Range Manually Electronically acoustic signals 51 70 9 0 12 5 10 4 10 43 50 7 6 8 9 9 9 37 42 6 5 7 5 IV 1 8 8 29 36 5 1 6 4 7 7 23 28 4 0 5 0 6 6 19 22 3 3 3 9 Mm 5 5 15 18 2 6 3 2 4 4 11 14 1 9 2 5 Il ot 3 3 4 10 0 7 1 8 I 11 2 2 1 under 4 under 0 7 no salt 1 necessary 1 The water hardness will only be indicated acoustically if the acoustic signal has been activated 2 d German degree measure of the hardness of water 3 mmol l millimol per litre international unit for the hardness of water 4 On this setting the length of the dishwashing cycle may be slightly longer Factory setting Operating Instructions Open the dishwasher door Remove the lower rack from the Turn the hardness range switch to 0 Replace the lower
20. delay is selected The washing compartment is made from rust free stainless steel Rust spots in the wash Solution Shut the door Insert mains plug Replace fuse If dishes are to be washed immediately cancel delay start timer Only wash cutlery and dishes that are suitable for dish washer use ing compartment are due to rust particles from external sources rust particles from water pipes pans cutlery etc Remove such spots with one of the stainless steel cleaners that are generally available on the market Rust spots are visible in the washing compart mena Close the lid of the special salt container securely Use a different brand of detergent The whistling is not a cause for concern There is a whistling noise during washing the wash results are not satisfactory The dishes are still dirty The wrong wash programme was selected The dishes were loaded is such a way that the wash waster did not reach all items The baskets for the dishes must not be overloaded The filter in the base of the washing compartment is dirty or incor rectly positioned Detergent was not used or too little was used In the case of scale deposits on the dishes The special salt container is empty or the water softener is incorrectly adjusted The drain hose is incorrectly laid The dishes are wet and dull Rinse aid was not used The rinse aid container is empty 34 Operating Ins
21. e dishwashing cycle has been cancelled Load Sensing Sensor Logic If a wash programme is started even though there are only a few dishes in the upper and or lower basket an intelligent electronic system adjusts the amount of water and the duration of the wash programme to the number of dishes By this means it is possible to wash only a few dishes quickly and economically At half load 6 place settings up to 2 litres of water and 0 2 kWh of electricity are saved 29 Operating Instructions Switching off the dishwasher If the acoustic signal has been enabled a continuous tone will sound for 15 seconds at the end of the programme Hot steam may escape if the door is opened immediately after the pro gramme has ended Therefore 1 Open the door carefully Switch off the dishwasher by pressing the ON OFF button All display indicators will go out If you do not switch off the dishwasher the acoustic signal will sound again 3 minutes later and 6 minutes later Removing the dishes e Hot dishes are sensitive to knocks The dishes should therefore be allowed to cool before they are removed e Leave the dishes in the dishwasher for approximately 15 minutes fol lowing the end of the programme to enable better drying and cool ing down of dishes e Empty the lower basket first then the upper basket This will avoid water spots which are caused by remaining water in the upper bas ket dripping onto the dishes in th
22. e lower basket Care and Cleaning AN 30 Do not under any circumstances use furniture care products or aggres sive cleaners e f necessary clean the controls only with a soft cloth and pure warm water e Occasionally check the internal containers door seal and water inlet for soiling clean if necessary Operating Instructions Cleaning the Filter The filters should be checked and cleaned regularly Dirty filters will give poor wash results Open the door remove the lower basket The dishwasher filter system com prises a coarse fine filter microfilter and a flat filter Unlock the filter sys tem using the handle on the microfil ter and remove Turn the handle about 1 4 a turn anti clockwise and remove Take hold of the coarse fine filter 1 2 by the handle with the hole and remove from the microfilter 3 Clean all filters thoroughly under running water Remove the flat filter 4 from the base of the washing compartment and clean both faces thoroughly Put the flat filter back in the base of the washing compartment Place the coarse fine filter in the microfilter and press together Put the filter combination in place and lock by turning the handle clock wise to the stop During this process ensure that the flat filter does not protrude above the base of the wash ing compartment The dishwasher must not be used without filters under any circum
23. ed when the dishwasher is in position e In addition the dishwasher must be firmly screwed to the work sur face or to the neighbouring units This is essential to ensure the dish washer does not tip see installation template supplied The door of the appliance can be fitted with a furniture door panel of the following dimensions Width 591 mm 594 mm Thickness 16 mm 24 mm Height max 715 mm Weight max 10 kg 37 Installation and Connection Instructions 38 Connecting the Dishwasher Water Connection ee The dishwasher is fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations e The dishwasher must be connected to a cold water supply e The dishwasher must not be connected to open hot water appliances or instantaneous water heaters Permitted water pressure Lowest permitted water pressure Consult your installer if the water pres 1 bar 10 N cm 100 kPa sure is less than 1 bar Highest permitted water pressure In the case of a water pressure greater 10 bar 100 N cm 1 MPa than 10 bar a pressure reduction valve must be used available from your dealer Connect the inlet hose The water inlet hose must not be kinked crushed or entangled when it is being connected up Connect the threaded hose fitting ISO 228 1 2000 on the water inlet hose to a tap with an external thread
24. er of acoustic signals correspond to the new hardness setting This sequence of flashes and acoustic signals is repeated many times with a 5 second pause in between 11 Operating Instructions 8 Pressing function button 1 increases the hardness setting by 1 Exception hardness setting 1 follows hardness setting 10 9 When the hardness setting is correct press the ON OFF switch The hardness setting is now saved Special salt for the water softener i If the water hardness in your area is less than 4 d then the water in your dishwasher does not need to be softened and you do not need to use special salt or salt substitute Water can be softened in one of two ways e f you are using dishwasher detergent that already contains salt sub stitute the detergent only is put into the detergent compartment In this case the water softener must manually be set to O and electronically to 1 to ensure that no special salt is added e f you are using dishwasher detergent and special salt separately the special salt is to be put into the salt container In this case the water softener must manually be set to 0 and electronically to between 2 and 10 depending on the water hardness in your area to ensure that the special salt is dispensed from the salt container Only use special salt intended for dishwashers Never fill the salt supply container with different types of salt e g cooking or table salt o
25. ght position are a potential hazard Long and or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket Take care when loading or unload ing sharp items such as knives To ensure that all items of cutlery are completely washed you should ts 1 Place the grid insert on the cutlery rack 2 Place short knives forks and spoons in the grid insert with their handles pointing downwards 3 For larger items of cutlery e g a whisk half of the top for the cut i p ia lery basket can be left off EEREN a DAN EDSS h n my paR ESC irecy ce eas Doma eee ans mA es onary ees lamanta Te Srn E SEERE EEr RERS W REEN C On some models of dishwasher it is possible to open the cutlery basket AN To ensure that the cutlery rack cannot open on removal from the appliance you should always hold both parts of the two part handle t 1 Place the cutlery rack on a table or work surface 2 Open the two part handle 3 Remove cutlery 4 Close the two part handle Operating Instructions Loading Pans Frying Pans and Large Plates Load large and heavily soiled dishes in the lower basket Plates up to 29cm in diameter
26. he most suitable wash programme with the aid of this table Type of Dishes In Addition Type of Soiling Suitable Programme Programme Sequence 3 Consumption Figures 4 Duration Energy Water Dinner Service and Cooking Utensils e heavily soiled e dried on left overs particu larly egg white and thickeners INTENSIV CARE 70 Pre wash Main wash 2x Rinsing Final rinse Drying u 120 130 min 1 80 2 00 kWh 22 24 litres Dishes without Pans with non temper ature resistant dishes e average soiled e just used average to slightly soiled particularly suitable Coffee Service and Dessert Dishes with non temper ature resistant dishes e average to slightly soiled when concentrated detergents are used NORMAL 65 Pre wash Main wash Rinsing Final rinse Drying 90 100 min 1 20 1 40 kWh 17 19 litres 30 MIN Main wash Final rinse u 30 min 0 8 kWh 9 litres 1 This programme is not suitable when left overs have dried on 2 Test programme for test institutes 3 Noise levels vary at different stages of the wash programme as at some programme stages the dishes are washed more energetically so that they will be cleaned more thoroughly ECO 50 2 Pre wash Main wash Rinsing Final rinse Drying vu 130 150 min 0 95 1 05 kWh 14 16 litres 4 The consumption figures were determined under standa
27. ing cycle before closing the dishwasher door briefly press the button for the new dishwashing cycle If you would like to change the dishwashing cycle after the cycle has commenced proceed as follows Hot steam may escape when the dishwasher door is opened There is a risk of scalding Carefully open the door of the dishwasher 1 Open the door of the dishwasher The dishwashing cycle will stop Press the button for the new dishwashing cycle and hold it down First the indicator for the dishwashing cycle that is currently running will flash After several seconds only the indicator for the new dishwashing cycle will be flashing Operating Instructions Release the cycle button Close the dishwasher door The newly selected dishwashing cycle will Open the door of the dishwasher The dishwashing cycle will stop Close the dishwasher door The dishwashing cycle will continue Open the door of the dishwasher Press function buttons 2 and 3 for approx 1 second and keep them Release the function buttons Switch off the dishwasher by pressing the ON OFF button commence from the beginning Interrupting the dishwashing cycle by opening the dishwasher door Cancelling the dishwashing cycle pressed The LED indicators for all programme buttons and the button for the delay start timer if present light up The LED indicators and any option buttons that are present only light up if they are activated Th
28. ll the packag ing materials used are harmless to the environment and can be recy cled e Plastic parts are marked with standard international abbreviations gt PE lt for polyethylene e g sheet wrapping material gt PS lt for polystyrene e g padding material always CFC free gt POM lt for polyoxymethylene e g plastic clips e Cardboard packaging is manufactured from recycled paper and should be deposited in the waste paper collection for recycling Disposal of Old Appliances When disposing of old appliances remove the plug and ensure that any locks or catches are removed to prevent young children becoming trapped inside Use an authorised disposal site Economical and Ecological Dishwashing e Ensure that the water softener is correctly adjusted e Do not pre rinse dishes under running water e When you wash a small load the load sensor calculates the amount of water necessary and shortens the programme It is more economi cal to always wash with a full load e Select the wash programme to suit the nature and degree of the soil ing on the dishes e Do not use more detergent special salt or rinse aid than is recom mended in these operating instructions and by the detergent manu facturer Operating Instructions Appliance Features Display and Control Panel Top Spray Nozzle Rubber Seal for Connecting the Water Feed to the Spray Arm Spray Arms Water Hard
29. mbi Detergent Tablets 22 200000 25 Concentrated Detergent 1 0 0 cc cece cece eens 26 Detergent tablets ai sirat stich a Ee nk at eta SEES ee edie 26 Selecting the Wash Programme Programme Table 005 27 Starting a dishwashing cycle 0 cc cece eee ete 28 Changing interrupting cancelling a dishwashing cycle 28 Load Sensing Sensor Logic 2 cece eee eee 29 Switching off the dishwasher 000s cece eee eee eens 30 Care and Cleaning 0c cece cece teens 30 Cleaning the Filter ucesnici a eee eee eee 31 Contents What to dos ihe aethere ranae a E ore etarel sareud E aa 32 Error messages are displayed 2 0 ccc eee 32 there are problems with the operation of the dishwasher 34 the wash results are not satisfactory 00 cece eee eee eee 34 Technical Data 320 6 fie aed deh Sater dee Daa ga aah 35 Notes for Test Institutes 0 00 0 cece eee 36 Installation and Connection Instructions 37 Installing the Dishwasher 00000 ccc eee eee eee 37 Fitting the Furniture Door Panel 0000 37 Connecting the Dishwasher 2200000 cece eee eee eee 38 Water Connection sisaria or a a wkd Ove Ld Gena Wes bly Os 38 Permitted water pressure 0 cece eens 38 Connect the inletihose si hociaecncae was AEE an AEE eee 38 Wate rd Ee NA OSESE EE iat saaconiie pian s k
30. must still be accessible after the appliance has been installed Changing a fuse The appliance is supplied with a 13amp plug fitted In the event of hav ing to change the fuse in the plug supplied a 13amp ASTA approved BS 1363A fuse must be used Should the plug need to be Green replaced for any reason proceed as amp Yellow described below The wires on the mains lead are coloured in accordance with the following code Green and Yellow Earth Blue Neutral Brown Live e The wire coloured green and yellow must be connected to the termi nal marked with the letter E or by the earth symbol or coloured green and yellow e The wire coloured blue must be connected to the terminal N or col oured black e The wire coloured brown must be connected to the terminal marked L or coloured red e Upon completion there must be no cut or stray strands of wire present and the cord clamp must be secure over the outer sheath WARNING A cut off plug inserted into a 13 amp socket is a seri ous safety shock hazard Ensure that if it is necessary to cut off the plug it is disposed of safely and not retained Installation and Connection Instructions Connections The water inlet and drain hoses as well as the mains cable must be connected beside the dishwasher as there is insufficient space behind the appliance The plumbing and electrical installation example given below can only be regarded as a recommendati
31. ne at the address below or visit our website at www aeg co uk Customer Care Department AEG Domestic Appliances 55 77 High Street Slough Berkshire SL1 1DZ Tel 08705 350350 Calls may be recorded for training purposes re a From the Electrolux Group The world s No 1 choice The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and outdoor use More than 55 million Electrolux Group products such as refrigerators cookers washing machines vacuum cleaners chain saws and lawn mowers are sold each year to a value of approx USD 14 billion in more than 150 countries around the world AEG Hausger te GmbH Postfach 1036 D 90327 Nurnberg http www aeg hausgeraete de Copyright by AEG 822 961 332 00 1203 Subject to change without notice
32. ness Switch Container for Special Salt Container for Rinse Aid Detergent _ Dispenser Display and Control Panel Rating plate Filters Operating Instructions Display and control panel Function buttons Set start Display Set Control Indicators ON OFF button delay start delay INTENSIV NORMAL zomin ECO d AL CARE70 5 SOMIN 50 mh zag 0 i T T T T rmh l m EOS h Indicator for End of Wash Programme Function buttons In addition to the dishwashing cycle the following functions can also be set with the help of these buttons Function button 1 Set water softener Function button 2 Activate deactivate rinse aid inflow Function button 3 Activate deactivate acoustic signal Control indicators have the following meanings S Refill special salt s Refill rinse aid i The indicators are never illuminated while a dishwashing cycle is run ning Prior to using for the first time Prior to using for the first time remove all the clips with which the baskets are secured for transport Then perform the following steps ts 1 Adjust the water softener 2 Fill the water softener with water and special salt 3 Fill the rinse aid dispenser with rinse aid il Special salt and rinse aid must not be added if you use 3 in 1 detergent tablets Operating Instructions Water softener To avoi
33. nlet hose or the safety valve in water If the water inlet hose or the safety valve is damaged remove the mains plug immediately A water inlet hose with safety valve must only be replaced by your local Service Force Centre 39 Installation and Connection Instructions 40 AN Water drain Drain hose The drain hose must not be kinked crushed or entangled e Connecting the drain hose Maximum permitted height 1 metre Minimum required height 40 cm above the lower edge of the machine Extension hoses e Extension hoses are available from AEG Service Force The internal diameter of the extension hoses must be 19 mm to ensure that the function of the appliance is not impeded e Hoses may be laid a maximum of 3 metres horizontally the maximum P permitted height for the connection ees for the drain hose is then 85 cm 300 cm Sink outlet connection 85 cm gt 40cm e The outlet of the drain hose 19 mm fits all commonly available sink outlet spigot types The outer diameter of the spigot connection must be at least 15 mm e The drain hose must be fixed to the sink outlet connection using the hose clamp supplied If the dishwasher is fitted at a high position If the dishwasher is installed at a high level and the drainhose connec tion is less than 30 cm from the bottom of the appliance adapter kit ET 111099520 must be fitted This is available from Cus
34. on Two 45 or Straight Connections Outer 19 mm Length 30 mm Double tap Water drain Water inlet Water Mains Water Mains socket Mains inlet cable drain cable 43 Guarantee Conditions GUARANTEE CONDITIONS Standard guarantee conditions We AEG undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereof is proved to be defective by reason only of faulty work manship or materials we will at our discretion repair or replace the same FREE OF CHARGE for labour materials or carriage on condition that e The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating plate e The appliance has been used for normal domestic purposes only and in accordance with the manufacturer s operating and maintenance instructions e The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us e All service work under this guarantee must be undertaken by a Service Force Centre Any appliance or defective part replaced shall become the Company s property e This guarantee is in addition to your statutory and other legal rights e Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside these hours in which case
35. r detergent This would destroy the water softener Prior to filling with salt please check each time that you really do have a packet of special salt in your hand Setting the amount of special salt to be added Some appliances are equipped with an additional 3 in 1 function If you use 3 in 1 dishwashing tablets and select the 3 in 1 function together with the programme the inflow of special salt does not have to be deactivated see 3 in 1 function Operating Instructions t 1 Set the water softener manually and electronically to the desired water hardness Manual Electronic Number ae setting setting of flashes pdaitioniotsperial salt 0 1 1 Do not add special salt Addition of special salt 0 1 2 10 2 to 10 via salt container factory setting i If the water softener is electronically set at 1 for the purpose of using detergent that includes special salt the special salt indicator is deacti vated Adding special salt If you are using dishwasher detergent and special salt separately add the special salt Before using the dishwasher for the first time When the indicator for special salt is illuminated on the control panel t 1 Open the door remove the lower basket 2 Undo the lid on the salt container by turning it anticlockwise 3 When using for the first time fill the salt container with water 4 Place the funnel supplied on the con tainer opening Fill the container with salt
36. rack Setting the water softener Using the table as a guide adjust the water softener to that which cor responds to the hardness of the water in your area The dishwasher must be switched off Setting manually dishwasher or 1 see table Setting electronically Press the ON OFF button The LED indicators for all programme buttons and the button for the delay start timer if present light up The LED indicators and any option buttons that are present only light up if they are activated If the only LED indicator illuminated is one that belongs to a pro gramme button this means that this dishwashing cycle has been acti vated The dishwashing cycle must be cancelled Press function buttons 2 and 3 simultaneously for approx 1 second The LED indicators for all programme buttons and the button for the delay start timer if present light up The LED indicators and any option buttons that are present only light up if they are activated Press function buttons 2 and 3 simultaneously and keep them pressed The LED indicators for function buttons 1 to 3 will flash Press function button 1 The LED indicator for function button 1 will flash The LED indicator for the end of the dishwashing cycle is flashing and acoustic signals can be heard simultaneously only when the acoustic signal has been acti vated The number of times that the LED indicator for the end of the cycle flashes and the numb
37. rd conditions They are intended as a guide only and depend on the loading For this reason figures may vary in practice 5 When the hardness setting is electronically adjusted to 10 the length of the dishwash ing cycle may be slightly longer 27 Operating Instructions 28 Starting a dishwashing cycle is 1 2 Check that the dishes and cutlery are stacked in the dishwasher in such a way that the spray arms are free to rotate Turn on the tap fully 3 Press the ON OFF button The LED indicators for all programme buttons and the button for the delay start timer if present light up The LED indicators and any option buttons that are present only light up if they are activated Press the relevant button for the cycle required see Programme Table The cycle display will become illuminated Close the dishwasher door The dishwashing cycle will begin If an acoustic error message can be heard after the cycle has begun please read the section What to do if Changing interrupting cancelling a dishwashing cycle Only change or interrupt a dishwashing cycle that is in progress if it is absolutely necessary After the appliance has been closed again the air that has entered will be heated significantly and expand As a result water may collect in the base of the appliance and trigger the anti flood system Changing a dishwashing cycle If you would like to change the dishwash
38. th the product e Keep all packaging away from children e Keep all detergents in a safe place out of children s reach e The water in your dishwasher is not suitable for drinking If there are still remnants of detergent in the appliance there is a risk of burns e When disposing of an old appliance cut off the power supply cable and remove any door catches to prevent young children being trapped inside General Safety e Repairs to the dishwasher are only to be carried out by qualified serv ice engineers Improper repairs can give rise to significant hazards for the user If your appliance needs repairing please contact your local AEG Service Force Centre Operating Instructions e Never place the dishwasher in operation if the mains cable water inlet or drain hose is damaged or the control panel work top or plinth area is damaged such that the inside of the appliance is freely accessible e If the mains lead is damaged or is to be replaced for a longer lead the cable obtainable from AEG Service Force must be replaced by a service engineer authorised by AEG e Never unplug the appliance by pulling on the cable always pull the plug e Additions or modifications to the dishwasher are not permitted for safety reasons e Ensure that the door of the dishwasher is always closed when it is not being loaded or unloaded In this way you will avoid anybody tripping over the open door and hurting themselves e Long
39. tomer Service Discharging into a standpipe When discharging into a standpipe the upright standpipe should have a minimum length of 30 cm 12 from the bottom of the elbow to the top of the pipe see diagram Make sure that it is designed in such a way that the end of the drain hose cannot be covered with water Min 38mm 1 5 diameter standpipe Min 30 cm 12 Installation and Connection Instructions Leak prevention system To avoid damage caused by water leakage the dishwasher is equipped with a leak prevention system In the event of a fault the safety valve in the appliance immediately interrupts the inflow of water and the drain pump is activated In this way water can neither escape nor overflow Any remaining water in the appliance is automatically pumped out In the event of a fault when the appliance is switched on a buzzing tone can also be heard 41 Installation and Connection Instructions 42 Electrical Connection AN Any electrical work required to install this appliance should be car ried out by a qualified electrician or competent person WARNING This appliance must be earthed The manufacturer declines any responsibility should these safety measures not be observed Before switching on make sure the electricity supply voltage is the same as that indicated on the appliance rating plate To isolate the dishwasher from the mains remove the mains plug Important The plug
40. tructions There are streaks milky spots or a bluish coating on glasses and dishes Lower rinse aid dosing There are dried water drops on the glasses and dishes Increase rinse aid dosing The detergent may be the cause Contact the detergent manufac turer s customer advisor Technical Data Capacity 12 place settings including serving dishes Permitted Water 10 2T Pressure 1 10 bar 10 100 N em 0 1 1 0 MPa Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher door on the right Electrical Connection Dishwasher Free Standing Appliances Dimensions 850 x 598 x 598 H x W x D in mm Max Weight 54 Kg Dishwashers that Can Be Integrated Built In Dishwashers Dimensions 820 880 x 596 x 570 H x W x D in mm Max Weight 50 Kg Dishwashers that Can Be Fully Integrated Dimensions 820 880 x 596 x 546 H x W x D in mm Max Weight 50 Kg C This appliance conforms with the following EU Directives 73 23 EWG dated 19 02 1973 Low Voltage Directive 89 336 EWG dated 03 05 1989 including Directive Amendment 92 31 EWG EMC Directive 35 Operating Instructions 36 Notes for Test Institutes Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the test programme see Programme Table Tests in accordance with EN 50242 must be carried out when the salt dispenser and rinse
41. uction manual If you decide to switch to the use of a standard detergent system we advise that you e Refill both the salt and rinse aid compartments e Switch the waterhardness setting to the highest possible position and run for three normal cycles without a load e Readjust the waterhardness setting again according to the conditions for your region as per the instruction manual 25 Operating Instructions 26 Concentrated Detergent Based on their chemical composition dishwasher detergents can be split into two basic types conventional alkaline detergents with caustic components low alkaline concentrated detergents with natural enzymes The use of 50 C wash programmes in conjunction with concentrated detergents reduces pollution and is good for your dishes these wash programmes are specially matched to the dirt dissolving properties of the enzymes in the concentrated detergent For this reason 50 C wash programmes in which concentrated detergents are used can achieve the same results that can otherwise only be achieved using 65 C pro grammes Detergent tablets Detergent tablets of different makes dissolve at different speeds For this reason some detergent tablets cannot develop their full cleaning power during short programmes Therefore please use wash pro grammes with pre wash when using detergent tablets Operating Instructions Selecting the Wash Programme Programme Table Choose t
42. y option buttons that are present only light up if they are activated 2 Press function buttons 2 and 3 simultaneously and keep them pressed The LED indicators for function buttons 1 to 3 will flash 3 Press function button 2 The LED indicator for function button 2 will flash The indicator will indicate the current setting The indicator will Rinse aid inflow activated become illuminated ex factory setting The indicator is not illu minated Inflow of rinse aid is deactivated 4 Pressing function button 2 activates and deactivates the rinse aid dis pensing function 5 If the rinse aid dispensing function has been correctly set press the ON OFF switch The setting of the rinse aid dispensing function is now saved 15 Operating Instructions Open the door Press the rinse aid compartment Fully open the rinse aid compartment lid Qt Gv lt gt Fill with rinse aid exactly up to the Close the lid and press until it locks Wipe up any spilt rinse aid with a Adding rinse aid If you are using dishwasher detergent and rinse aid separately add the rinse aid Before using the dishwasher for the first time When the 3 indicator on the control panel is illuminated The rinse aid compartment is on the inside of the dishwasher door release button with your finger NIe alles level marked max this corresponds to a quantity of approx 140 ml
Download Pdf Manuals
Related Search