Edelbrock 1400 Automobile Parts User Manual
Contents
1. Catalog 1400 2007 Edelbrock Corporation Rev 1 07 RS mc Page 5 of 5 Brochure 63 0443 Edelbrock Corporation e 2700 California St Torrance CA 90503 Tech Line 800 416 8628 e E Mail Edelbrock Edelbrock com Catalog 1400 2007 Edelbrock Corporation Rev 1 07 RS mc Brochure 63 04432. Carburetor doesn t adjust properly Carburetor floods Fuel leaks at shaft Internal fuel leak Misses or surges Stumbles or loads up Engine won t idle Rough idle Backfires Hard starting Lack of power Pinging at moderate cruise just off idle Engine stalls on hard braking Low fuel economy Bogs Possible Solutions Check for air leaks Make sure carburetor and manifold gaskets seal properly All outlets must be plugged or connected Check ignition system Replace parts as necessary Adjust timing to proper specifications Check choke adjustment Change carburetor fuel filter and or in line fuel filter Check float level and drop Check idle mixture screw adjustment Increase accelerator pump stroke Pump squirter size change may be needed Off road vehicle may need spring loaded needle and seat kit Check for dirt or metal in needles and seats Needles and seats may need replacement Check for dirt blocking the low speed circuit Clean unit and apply air pressure Install in line fuel filter 8873 Check floats for leakage Replace if necessary Check air horn gasket Replace if deterioration or breakage is present Fuel is boiling due to excessive under hood temperature Fuel pressure too high Fuel regulator may be needed Fuel pressure too low Check fuel system Check secondary latching device and rod for proper movement Lower float level from 11 32 to 7 16
3. 6 wire with a 90 degree bend 1 8 from the end between the top of the slot in the choke piston cylinder and the bottom of the slot in the piston Hold the wire in position and close the choke valve by pressing on piston lever A until resistance is felt The dimension C should be 100 between the top edge of the choke valve and the air horn To adjust bend rod B lt 6 100 To adjust the fast idle linkage See Figure 6 place the fast idle screw A between the two notches on the cam Close the choke valve as far as possible without forcing it The dimension C should be 3 64 between the choke valve and the air horn To adjust bend rod B Fast idle may be adjusted to manu facturer s specifications usually 1500 rpm during normal choke cold operation The fast idle screw A can be adjusted with engine off and throttle held open to allow screw head access Re check fast idle speed after each adjustment gt lt _ E 3 64 Catalog 1400 Rev 1 07 RS mc Page 4 of 5 The length of time during which the choke will stay closed is determined by the position of the choke cap As the choke cap is turned clockwise the choke will stay closed longer To properly set the choke turn the choke cap to the leanest notch on the choke housing tighten the choke housing retaining screws and run the engine until normal operating temperature is reached With the engine running slowly tu
4. EDELBROCK PERFORMER SERIES EMISSIONS LEGAL CARBURETOR 600cfm Electric Choke EGR Square Bore Carburetor Catalog 1400 INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation Most installations can be accomplished with common tools and procedures However you should be familiar with and comfortable working on your vehicle If you do not feel comfortable performing this installation it is recommended to have the installation completed by a qualified mechanic If you have any questions please call our Technical Hotline at 1 800 416 8628 7 00 am 5 00 pm Pacific Standard Time Monday through Friday or e mail us at Edelbrock Edelbrock com IMPORTANT NOTE Proper installation is the responsibility of the installer Improper installation will void your warranty and may result in poor performance and engine or vehicle damage DESCRIPTION Edelbrock Performer Series carburetor 1400 is 50 state street legal for all 1980 and earlier General Motors V8 engines All Performer Series Carburetors have been calibrated factory flow tested and preset Edelbrock Performer Series carburetors are designed to give you excellent performance fuel economy and maintenance free operation To ensure that you enjoy these benefits please read all instructions prior to installation NOTE Edelbrock Performer Series carburetors are not for computer controlled applications That includes some 1981 amp later GM vehic
5. d Q Check the ignition system clean and gap or replace spark plugs Q Check all hoses for leaks or cracks and replace if necessary plug wires and adjust ignition timing LI Check fuel pump for proper operation and replace if necessary ACCESSORIES REVIEW THE FOLLOWING AND USE PARTS AS NECESSARY FOR YOUR APPLICATION LU Carburetor Adapter and Fuel Line Kit 2697 Used to mount LI GM cruise control adapter 1484 Edelbrock carburetors to stock Quadrajet manifolds Includes LI Throttle cable transmission and cruise control bracket 8031 or 4 hole carb adapter 2696 fuel filter and fuel line kit 8135 for 8036 79 and earlier for small block or big block Chevy Some 3 8 and 5 16 OEM steel fuel lines Both also available separately applications may require modification to stock bracket Q 90 degree banjo fuel inlet fitting kit 8089 For use with low profile LI EGR adapter 1476 For Chevy small block V8 s Required for all air cleaner bases 6 AN fuel inlet fitting 8087 or Inverted Flare EGR applications to provide clearance for Performer Series fuel line fitting 8090 3 8 carburetors Q In line fuel filter 8873 Q Universal throttle return spring kit 8005 If original return spring Q Fuel pressure regulator 8190 If stock fuel pressure is greater than cannot be used 6 5 psi Q 3 4 Air Cleaner spacer 8092 For low profile air cleaner bases to Q Chevrolet throttle cable stud 8009 77 amp later clear electric chok
6. e Q Transmission kick down stud 8018 TH350 type LI Electrical connectors For electric choke connection Catalog 1400 2007 Edelbrock Corporation Rev 1 07 RS mc Page 1 of 5 Brochure 63 0443 RECOMMENDED TOOLS Q Sockets wrenches tubing wrenches a Q Pliers Q QO Screwdrivers m Q Hacksaw and or tubing cutter 20 Torx Driver for electric choke models Wire crimpers for electric choke models Test Meter or Test Light for electric choke models INSTALLATION PROCEDURE FUEL INLET for 3 8 hose Except marine IDLE MIXTURE SCREWS models 1409 amp 1410 which use a 3 8 Left side screw for left side of carb inverted flare fitting Right side screw for right side of carb CANISTER VAPOR VENT 1400 ONLY POWER BRAKE PORT Except Marine Models Rear lower side 1 4 NPT MUST BE PLUGGED WITH 1 4 PIPE PLUG SUPPLIED IF NOT USED IDLE SPEED SCREW PART NUMBER is stamped on 3 16 TIMED VACUUM PORT PCV PORT For 3 8 hose 3 16 MANIFOLD VACUUM PORT pad at front of carburetor Distributor vacuum advance port for emissions controlled engines NOT FOR FUEL EGR vacuum supply port Figure 1 Fittings and Vacuum Port Locations CARBURETOR PREPARATION 1 Install proper throttle and transmission linkage for your particular application Make sure all linkage is properly secured to carburetor and works freely 2 Check and prepare carburetor for proper vacuum fitting installation EGR power b
7. h used Bend locking tabs on special washer over flats of the nut to prevent loosening Attach the wire from the solenoid to the existing C E C wiring connector If the factory connector does not fit you will need to splice into the wire from the connector Use a 1 4 female receptacle and at least 18 20 gauge wire Some receptacles will require that the locking tab on the solenoid be flattened before the receptacle will fit ADJUSTMENT With the Idle Compensator Solenoid disconnected adjust the Idle Speed Screw until you reach the desired idle RPM With the Idle Compensator Solenoid connected and the ignition in the On position adjust the solenoid until it just contacts the throttle lever Next start the engine and turn the Idle Speed Screw counter clockwise to make sure the idle speed is maintained by the solenoid If necessary adjust idle speed by turning solenoid plunger in or out with a 1 2 wrench Shut off the engine Turn the Idle Speed Screw counter clockwise until the throttle lever is completely closed and the Idle Speed Screw is not touching the throttle lever Turn the Idle Speed Scruew clockwise until it just makes contact with the throttle lever Continue turing 1 4 turn more This will make sure the throttle blades will not bind in the bore when the solenoid is turned off 2007 Edelbrock Corporation Brochure 63 0443 TROUBLESHOOTING CHART Refer to the chart below for reference Symptoms
8. les with Q Jet carburetor and some 1981 amp later Ford vehicles with automatic overdrive AOD transmissions Vehicles equipped with G E G solenoids will require the use of Edelbrocks Idle Compensator Solenoid Use part 8059 The factory C E C solenoid will not fit our throttle lever However the Edelbrock Idle Compensator Solenoid will allow you to retain the C E C function and to pass visual emissions inspection in California See C E C Function in the Adjustments and Troubleshooting section for installation and adjustment of the Idle Compensator KIT CONTENTS Q1 Installation instruction sheet Q2 5 32 Vacuum caps Q1 3 16 Internal star washer n1 Warranty card Q1 5 32 Vacuum T Q1 Red choke positive wire Q1 Square bore heat insulating gasket Q1 1 4 NPT pipe plug Q1 Black choke ground wire 1 Air horn gasket 1 Throttle cable ball end stud Q1 E O Decal LIT Air cleaner stud Q1 10 32 Hex nut CHECK THE FOLLOWING BEFORE BEGINNING INSTALLATION WARNING WHEN WORKING AROUND GASOLINE ALWAYS WORK IN A WELL VENTILATED AREA AND KEEP ALL OPEN FLAMES SPARKS AND OTHER SOURCES OF IGNITION AWAY FROM THE WORK AREA FAILURE TO DO SO CAN RESULT IN A FIRE OR EXPLOSION LI Replace fuel filter Dirt found in carburetor voids warranty Q Check the intake manifold and cylinder head gaskets for leaks and Q Check and replace the air filter if necessary replace if necessary Q Check PCV valve and replace if clogge
9. mp is turned on or when the engine is first started watch closely for signs of flooding If flooding occurs turn engine off immediately and lightly tap on the side of the carburetor that is flooding in the rear needle and seat area with a rawhide mallet or wooden handle of a hammer Start engine and see if flooding continues If flooding continues stop the engine Clean up any raw gasoline and refer to the Adjustments and Troubleshooting section of the Instruction Sheet WARNING NEVER POUR FUEL DIRECTLY DOWN THE CARBURETOR WHEN ATTEMPTING TO START THE ENGINE THIS MAY CAUSE A BACKFIRE AND POSSIBLE ENGINE COMPARTMENT FIRE RESULTING IN ENGINE OR VEHICLE DAMAGE PERSONAL INJURY AND OR DEATH 10 With engine at normal operating temperature and choke fully open set idle speed and mixture screws This procedure is outlined in the Instruction Sheet ADJUSTMENTS AND TROUBLESHOOTING IDLE MIXTURE The Edelbrock Performer Series carburetor has conventional Idle Mixture Screws IMS that provide a leaner A F when turned clockwise and richer A F when turned counter clockwise The idle air flow is controlled by a conventional screw that opens the Primary Throttles The following procedure should be used to set the idle mixture and speeds 1 Fully warm engine and ensure choke is fully open 2 Air cleaner in place 3 Set desired speed with the air screw 4 Adjust the IMS on ONE side to get the maximum possible RPM Do not go rich be
10. not responded to changes in the basic metering move the pump drive link to one of the holes closer to the carburetor body This will increase the stroke length of the plunger and result in more pump delivery FLOAT ADJUSTMENT To properly adjust the floats in the EPS carburetor two procedures must be followed First the metering rod power piston assemblies should be removed from the top of the carb airhorn Next remove the accelerator pump connecting rod and the choke connec ting rod After removing all the airhorn retaining screws turn the airhorn upside down with the gasket in place See Figure 3 Use a scale or a 7 16 drill bit as shown to mea sure the float level There should be 7 16 between the air horn gasket and the top of the outer end of the float To adjust the float level bend the float lever until the recommended level is attained DO NOT press the needle into the seat when adjusting the float lever Next you should check the float drop See Figure 4 Hold the airhorn upright and let the floats hang down There should be 1 1 4 1 4 between the airhorn gasket and the top of the outer end of the float To adjust the float drop bend the tab on the back until the recommended float drop is attained Bend Here Float Level 7 16 2007 Edelbrock Corporation Brochure 63 0443 CHOKE ADJUSTMENT To adjust the choke piston linkage See Figure 5 open the choke valve and insert a 02
11. rakes PCV distributor transmission etc using supplied vacuum caps T and hose when applicable Before removing old carburetor determine if distributor vacuum advance port is timed no vacuum present at idle or manifold vacuum vacuum present at idle Black Wire To Ground Carb Body Red Wire To Key On 12V gt Source Not Coil or Alternator Fig 2 and use the matching vacuum port on your Edelbrock carburetor See INSTALLATION OF CARBURETOR Figure 1 f vacuum port at rear of carb is not used plug with a 1 4 1 pipe plug 3 For electric choke hook up See Figure 2 remove one choke housing retaining screw and install eyelet end of choke ground wire black to choke housing and reinstall screw Connect clip end of choke ground wire to negative spade terminal on choke housing Connect red wire spade terminal to positive terminal on choke housing Connect other end of red wire to an ignition key activated H 12 volt source DO NOT ATTACH TO COIL OR ALTERNATOR Ensure this source maintains 12 volts with engine running Catalog 1400 Rev 1 07 RS mc Page 2 of 5 Disconnect all linkages and lines from old carburetor noting their purpose for reassembly on new carburetor CAUTION When disconnecting fuel line avoid any exposure to sparks or open flame Note position of all throttle and transmission linkages and or cables for reassembly Remove old carburetor and flange ga
12. rn the choke cap clockwise until the choke valve begins to close Now turn the choke housing one notch counterclockwise LEAN and tighten the choke housing retaining screws Periodic re adjustment of the choke will be required as the temperature changes throughout the year After each adjustment verify that the choke valve opens fully after the engine is warm Do not overtighten the small Power Piston Cover screws when servicing metering rods They should only be tightened to 12 to 17 inch pounds Excessive torque will weaken or snap off the screw heads If this happens they may fall into the carburetor causing serious engine damage If an inch pound torque wrench is not available snug the screw until it just touches the plate then tighten 1 16th turn more C E C FUNCTION Vehicles equipped with C E G solenoids will require the use of Edelbrock s idie Compensator Solenoid Use part 8059 The factory C E C solenoid will not fit our throttle lever However the Edelbrock Idle Compensator Solenoid will allow you to retain the C E C function and to pass visual emissions inspection in California Remove front driver s side carb stud and replace with longer stud supplied in this kit Place bracket over the stud and install nut and washer on stud Position solenoid in bracket and install large washer locking tabs face the solenoid and locknut Tighten firmly but be careful not to over tighten due to the large size 1 1 4 of the wrenc
13. sket Do not allow gasket or other material to fall into manifold Place new carburetor gasket and adapters when applicable on the manifold Install carburetor and cross tighten nuts Be sure not to overtighten nuts 2007 Edelbrock Corporation Brochure 63 0443 3 Connect all throttle and transmission linkages and throttle return springs CAUTION At this point make sure all throttle and transmission linkages operate smoothly from idle to wide open throttle WOT and check return springs for proper pressure 4 Connect all vacuum hoses to their proper location on carburetor See Figure 1 Replace hoses that appear brittle or cracked 5 Connect fuel line to carburetor See Figure 1 Avoid contact with any sharp edges or areas of extreme heat For best results use Edelbrock in line fuel filter 8873 and fuel line kit 8135 6 Install new air horn gasket and air cleaner stud supplied Install air cleaner making sure it does not contact linkage or fuel line and has proper hood clearance Extremely low profile air cleaners will not fit without 8092 due to choke interference Z Trim air cleaner stud to proper length 8 Re check all linkage for smooth throttle operation 9 Start the engine and check for any possible fuel or vacuum leaks CAUTION Be alert to carburetor flooding Flooding can be caused by dirt small particles of hose cuttings floats and inlet needles which have settled during shipping When the fuel pu
14. yond the maximum speed point If the above changed the idle speed more than 40 RPM then re adjust the speed Adjust the side OPPOSITE of that in Step 4 to get maximum RPM Reset the speed Carefully trim each IMS to again get the maximum idle RPM Go leaner just enough to get a 20 RPM drop in speed Reset the speed to the desired RPM This is a Lean Best Idle Set Setting richer than this will not improve idle quality or performance but could tend to foul spark plugs WINTER FUEL IDLE SETS During the winter months in most parts of the country the local fuel will be a winter blend that is very volatile as an assist to cold engine starting and driveability during warm up However the high volatility has the disadvantage of allowing excessive vaporization of the fuel if the vehicle is operated in a heated area such as a garage This can result in problems in the idle set procedures since the carburetor s internal vents will allow this excess vapor to be drawn into the throats and enrichen the mixture The idle will be erratic and not seem to be able to hold a set To resolve this type of problem it is advisable to perform the final settings outdoors after the vehicle has been stabilized with a drive of several miles a Se eS sch Catalog 1400 Rev 1 07 RS mc Page 3 of 5 CALIBRATING THE ACCELERATOR PUMP If you encounter any hesitations or stumbles that do not seem to be related to the basic metering or have
Download Pdf Manuals
Related Search