D-Link airpremier n dual band poe access point Network Router User Manual
Contents
1. United States Telephone 877 354 6555 World Wide Web http support dlink com Canada Telephone 877 354 6560 World Wide Web http support dlink ca D Link Version 1 0 June 13 2011 Copyright 2011 D Link Corporation D Link Systems Inc All rights reserved D Link and the D Link logo are registered trademarks of D Link Corporation or its subsidiaries in the United States and other countries CloudCommand is a trademark of PowerCloud Systems Inc All rights reserved Other trademarks are the property of their respective owners Product specifications size and shape are subject to change without notice and actual product appearance may differ from that depicted herein2. Status IP Address 192 168 0 50 Subnet Mask 255 255 255 0 Default Gateway Device Name Primary DNS Secondary DNS Step 6 No additional configuration is required Within a few minutes the Access Point will self configure and become ready to use You have the option of later reconfiguring your Access Point to a new static IP address using the CloudCommand interface The DAP 2565 is PoE Power over Ethernet compliant You can power it either by using a PoE switch or the included power adapter Once powered the green power LED will turn ON to indicate proper operation Power over Ethernet Switch or Router Internet DAP 2565 Step 7 Restore setting change in Step 2 D Link powered by CloudCommand Dashboard To view your CloudCommand dashboard please log in at http dlink cloudcommand com The dashboard is your starting point to monitor network activity troubleshoot problems authorize and disconnect individual devices or make configuration changes to your Access Point s _ MyCompany CloudCommand x D Link Network Manager Cloud Commard Alerts amp Events Status 7 Access Point Traffic for Entire Network 2 Alerts Time Interval Last 1 hour v Connect R New Device New Access Point EDEL 7 O Devices Access Points Upload Settings 2 Admin amp Firmware Update Access Points 1 Support 7 FAQs Name A Status Contact CONF RM
3. 168 0 10 Subnet mask 255 255 255 O Default gateway m Click Use the following IP address Obtain DNS server address automatically Use the following DNS server addresses and enter an IP address that is on a the same subnet as your network MESTA or the LAN IP address on your new aiiin DAP 2565 Click OK twice to save your settings ANT Command 5 Step 3 Launch a web browser and type either the IP address of the access point default 192 168 0 50 or the default device name of the access point http dlinkapxxxx where xxxx are the last 4 numbers of the MAC address The MAC Address is on the lower left corner of the device label highlighted below D Link DAP 2565 b u ERR X m Model DAP 2565A1 ear A MAC ID XXXXXX000002 U AOR TO TOR VOR VOR ATTA TA Madein China CM J Step 4 Once you enter the IP address or device name the login screen will appear Login to the Access Point UserName _ Password _ Type admin in the User Name field Leave the Password field blank Click the Login button powered by C ude a LiUUU Command 6 Step 5 Once logged in you will be able to change the Access Point s IP address and DNS information to match your existing network configuration D Link DAP 2565 f Home Maintenance Configuration v S System B Logout M Help DAP 2555 H H Basic Settings E Cloud Manager Get IP From Static IP Manual
4. register it online Locate the Unit Identification Code UIC on the yellow label placed on the underside of your Access Point MAC ID XXXXXX000002 TTT Product Label Step 2 Go to http dlink cloudcommand com on a compatible browser Firefox 3 6 Chrome 5 0 Safari 4 0 Internet Explorer 8 0 or later versions Step 3 Choose the appropriate registration scenario New Customer If you don t have an existing CloudCommand account create one by following the instructions in our simple step by step wizard The wizard will guide you through the initial setup of your entire wireless network Existing Customer f you already have a CloudCommand account please log in In the left menu bar on your dashboard click New Access Point and follow the instructions CloudCommand Dashboard powered by ANT Command 3 Option 1 Deploying Your Access Point with Dynamic IP Addressing If your network automatically assigns IP addresses DHCP service connect the Access Point directly to the network by plugging an Ethernet cable into the LAN port on its rear panel Insert the cable s other end into your existing switch or router with Internet connectivity No additional configuration is required Within a few minutes the Access Point will self configure and become ready to use You have the option of later reconfiguring your Access Point to a static IP address using the CloudCommand interfac
5. 1 Active LOBBY Active AP OFFICE Active Reports Admin Download View Primary Network 0 connected devices Name mywireless Security WPA2 PSK AES IDA Jeane Desktop admin mycompany com Refresh 9 Log Off MyCompany f Entire fetwork Chart Access Point Device Total E LoBBY E CONF RM1 Guest Network 0 connected devices Name myguest Security Password Protected AP Connected Name AP Connected LOBBY Mark LOBBY CONF RM 1 Deanna CONF RM 1 Manage Access Points and connected devices View alerts and events and set up alert notifications Display detailed activity reports for users and Access Points Change configurations Wi Fi network names security and passwords View activity graphs So w G amp o View devices connected to your guest network AN Command 0000 View devices connected to your primary wireless network View Access Points in your network Read FAQs Register new Access Points Authorize a new device to connect to your wireless network Monitor alerts in real time Notes powered by AANT Command powered by Notes AN Command 10 powered by Notes AN Command 11 Technical Support D Link s website contains the latest user documentation and software updates for D Link products U S and Canadian customers can contact D Link Technical Support through our website or by phone
6. D Link e Quick Install Guide 9 DAP 2565 Ar Premier N Dual Band PoE Access Point powered by ANT Command Business Class Networking System Requirements Important Before connecting you must register your Access Point online To properly configure your Access Point you need Internet connectivity e Computer with a Windows Macintosh or Linux based operating system e Browser with Firefox 3 6 Chrome 5 0 Safari 4 0 Internet Explorer 8 0 or later versions e Note your Access Point includes a one year subscription to the CloudCommand online service After one year the service requires an annual subscription Package Contents If any of following items are missing please contact your reseller e D Link DAP 2565 AirPremier N Access Point powered by CloudCommand e Power Adapter Power Cord e CAT5 Ethernet Cable e Power over Ethernet Base Unit e Mounting Plate i RESET i 7 DAP 2565 E G Antennas G LAN Port Used to broadcast wireless network Connects DAP 2565 to the network and receive connections from clients via Ethernet cable 2 Reset Button Resets the Access Point to factory defaults D Link Welcome to D Link s line of cloud managed wireless Access Points Leverage the product s online interface to configure deploy secure and manage your entire wireless network Registering Your Access Point Online Step 1 Before you can use the Access Point you must
7. e The DAP 2565 is PoE Power over Ethernet compliant You can power it either by using a PoE switch or the included power adapter Once powered the green power LED will turn ON to indicate proper operation Switch or Router Internet DAP 2565 D Link Option 2 Deploying Your Access Point without Dynamic IP Addressing powered by If your network does not automatically assign IP addresses No DHCP service follow these steps to properly configure your Access Point Configure APs Step 1 Connect the Access Point directly to your computer using an Ethernet cable eed PC or Mac DAP 2565 Step 2 Configure the Ethernet connection of your computer as follows Windows 7 Click on Start gt Control Panel gt Network and Internet gt Network and Sharing Center gt Change Adapter Setting Windows Vista Click on Start gt Control Panel gt Network and Internet gt Network and Sharing Center gt Manage Network Connections Windows XP Click on Start gt Control Panel gt Network Connections Windows 2000 Right click My Network Places gt Properties Right click on the Local Area _ intemetProtocel Version a crip Propere Connection which represents your General You can get IP settings assigned automatically if your network supports network adapter and select Properties ee Highlight Internet Protocol TCP IP a RE Use wing IP address and click Properties IP address 192
Download Pdf Manuals
Related Search