Directed Electronics MAXX3 Automobile Alarm User Manual
Contents
1. M O DEL MAXX3 OWNERS GUIDE Table of Contents Consumer Warranty 3 What Is Included 5 Important Information 5 Your Warranty 6 Remote Controls 6 System Maintenance 7 Remote Control Battery Replacement 7 System Features 8 Stealth Coding Technology 8 Electronic Scan Prevention ESP 8 Interior Light Illumination 8 Passive Immobilisation 9 Valet Switch 2206 9 Keyless Entry in Valet Mode 9 Ultrasonic Sensors 9 Instant Remote Control Code Deletion 10 One Step Remote Control Code Learning 10 Alarm State Memory 10 Transmitter Functions 11 Accessory Outputs and Button Assignments 11 System Operation 12 Active Arming 12 Passive Arming 12 Disarming the System if alarm is not sounding 12 Disarming the System if alarm is sounding 13 Silent Arm Disarm 13 Remote Panic 26 13 Two Stage Unlock Capability 14 Sensor Bypass 14 Protected Valet Mode 15 How to Change Your PIN Code 17 Diagnostics susana essa 19 LED System Status Indicator 19 Previous Intrusion Alert 19 Specific Zone Intrusion Identification 19 Automatic Malfunction Override 20 Interpreting Chirps and Flashes 202. User Programmable Features 21 Passive Arming 2 21 Passive Arming With Door Lock 21 Auto Rearm and Lock 22 Ignition Controlled Door Lock Unlock 22 Long Term Silent Arm Disarm 23 Door Ajar Indication 23 Dual Sensor Trigger Mode 23 How to Set the User Programmable Features spa pp da iad de 24 Programming Table for System Features 26 Programming Table for Remote Controls 27 Security amp Convenience Expansions 28 Glossary of Terms 29 Quick Reference Guide 31 Health Check 33 22002 Directed Electronics Consumer Warranty For a period of five calendar years from the date of purchase of this vehicle security device Directed Electronics Inc promises to the ORIGINAL PURCHASER to repair or replace with a comparable reconditioned model free of cost the alarm control unit if proved to be defective in workmanship or material under normal use SO LONG AS THE SYSTEM WAS SOLD INSTALLED AND SERVICED BY AN AUTHORISED AVITAL INSTALLER AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS ORIGINALLY INSTALLED All other system parts are covered under the same warranty agreement for a period of one year If warranty service is necessary you must have a clear copy of your sales receipt containing all of the information required This warranty contains the entire agreement relating to warranty and supersedes all previous and cont
3. Accessory amp Button 23 Press any remote button s The siren Output Timed Channel 4 will chirp four times for confirmation Accessory Output Button S 24 Press any remote button s The siren Pulsed Latched amp Channel 5 will chirp five times for confirmation Remote Sensor Button d a 25 Press any remote button s The siren Bypass Channel 6 will chirp 6 times for confirmation All Channel Learn 20 Press button The siren wil chirp once to confirm factory preset order Instant Code Deletion 27 Wait 3 seconds The siren will chirp twice All remotes are erased from memory NOTE When assigning channels to different buttons than the factory settings you must All Channel Learn a transmitter and then change the individual assignments with feature number 20 to 25 as required 2002 Directed Electronics Inc 27 Security amp Convenience Expansions Listed below are some of the many expansion options available Please consult your dealer for a complete explanation of all the options available to you 28 Audio Sensor Metal on glass glass cracking and breaking glass produce distinctive acoustic signatures The 506T audio sensor uses a microphone to pick up sounds then analyses them with proprietary acoustic software to determine if the glass has been struck Backup Battery The 520T keeps the system armed triggers the alarm and keeps the Immobilisation circuits active if the main batter
4. ON Begin to press and release the Valet switch The siren will chirp once each time you press and release the Valet switch 2002 Directed Electronics Inc 6 Continue pressing and releasing the Valet switch counting the siren chirps NOTE Stop when you reach the number of chirps associated with your cho sen feature The system LED will give confirmation of the feature status If the LED is ON the feature is ON If the LED if OFF the feature is OFF 7 Follow the Secondary Action listed in the programming table You will hear one or two chirps and the system LED will give you confirmation that you have changed the feature 8 After you have programmed the feature you have chosen you can exit programming by turning the ignition key OFF You will hear two chirps to confirm exit of program mode If you wish to program additional features leave the ignition ON and press the Valet switch again The system will advance to the next feature Continue pressing and releasing the Valet switch until you have reached your next chosen feature 2002 Directed Electronics Inc 25 Programming Table for System Features 9 SLUNG INO Q MN EPUUTIUG H oli Passive Arming ON 2 Press button The siren will chirp once for OFF twice for ON Passive Arm OFF 3 Press button The siren will With Door Lock chirp once for OFF twice for ON Auto Rearm and ON 4 Press button The siren wil Door Lock chirp once for OFF twice
5. the Dual Sensor Trigger Mode feature is turned ON the system will require both the built in Ultrasonic sensor and the additional sensor to be activated at the same time in order to trig ger the alarm system This is especially useful on convertible vehi cles as the alarm can be armed even when the roof is down or at times when you wish to arm the alarm and leave the windows open 2002 Directed Electronics Inc 23 How to Set the User Programmable Features All system features and remote control features are accomplished by turning the ignition key to the ON position or starting the engine entering your Personal Identification Number PIN and pressing the Valet switch a preset number of times to access the feature you wish to program The system also allows you to add new remote controls in one step and delete lost or stolen remote controls 1 24 Programming cannot be accessed while the system is in Protected Valet Mode indicated by the LED on solid red Remove the system from Protected Valet Mode by turning on the ignition The LED should turn off automatically Select the feature you wish to program from the Programming Table for System Features or the Programming Table for Remote Controls Note the number of chirps associated with that feature To enter programming mode enter your existing PIN code number by following steps 1 12 in the Protected Valet Mode section of this guide Turn the ignition key
6. SION OF ANY AND ALL WARRANTY OF MERCHANTABILITY AND OR ANY AND ALL WAR RANTY OF FITNESS FOR A PARTICULAR PURPOSE AND OR ANY AND ALL WARRANTY OF NON INFRINGEMENT OF PATENTS IN THE UNITED STATES OF AMERICA AND OR ABROAD NEITHER THE MANUFACTURER OR ANY ENTITIES CONNECTED THEREWITH 2002 Directed Electronics 3 SHALL BE RESPONSIBLE OR LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL DAMAGES INCIDENTAL DAMAGES TOWING REPAIR REPLACEMENT DAMAGES FOR LOSS OF TIME LOSS OF EARNINGS COMMERCIAL LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE This warranty gives you specific legal rights Your statutory rights are not affected 4 92002 Directed Electronics Inc What Is Included m One Avital Maxx3 Control Unit m One Valet Switch m One Status LED m One 4 Button 10 Channel Remote Control m One 2 Button 3 Channel Remote Control m Two Ultrasonic Sensors m One Battery Back up Siren m One Certificate of Installation m Two Avital Window Decals Important Information Congratulations on your purchase of the Thatcham Evaluated Avital Maxx our top of the range vehicle security convenience system To fully benefit from the capabilities of your system we encourage you to read the Owner s Guide thoroughly If you have any prob lems or questions consult the dealer you purchase
7. System Maintenance Maintenance The Maxx system requires no maintenance except for remote con trol battery replacement when they reach the end of their useful life When the battery weakens operating range will be reduced and the LED will dim To replace your remote control battery use the following procedure Remote Control Battery Replacement To replace the battery in your AviGlo remote control follow the instructions below ps Carefully pry apart the two halves of the remote control with a small flat bladed screwdriver The bottom right hand corner of the remote casing has a small indent to allow the screw driver access N The lithium battery is the round silver disc about the size of a five pence piece Remove the old battery from the metal clip You should note that the side of the battery should face up and the side should face the circuit board Slide the new replacement battery into the metal clip UD Re align the two halves of the enclosure and snap together N 92002 Directed Electronics Inc System Features Stealth Coding Technology Coding Technology Stealth Coding technology offers the most advanced protection available against code grabbing devices which thieves may use to record the digital code transmitted by your remote control When you leave the area thieves can then play back the code to unlock the doors and de activate your system Avitals remote controls with Stealth Coding r
8. anch number 18 3 To enter programming mode m Enter your existing PIN code number by following steps 1 12 in the Protected Valet Mode section of this guide 2002 Directed Electronics Inc 17 18 E Turn the ignition key to the ON position then press and release your Valet switch 17 times You will hear a chirp each time you press the switch to help you count m When you reach branch number 17 stop and follow the instructions in the Secondary Action column in the programming table Example If you would like the first two digits of your new code to be one and one you would press button once and button once To enter the digits zero and zero you would press the sia and buttons together and go to the next step To enter the next two digits press the Valet switch once you will hear one chirp to move from program branch number 17 to 18 Stop and follow the instructions in the Secondary Action column in the programming table Example If the last two digits of your new code are two and two then press the button twice and the button twice To enter the digits one and zero you would press the d a button once and then go to step five The system will assume the second digit is a zero as you did not press the button to enter a number If you are satisfied that the code you entered is the correct one then turn off the ignition to exit programming and test your new code Should you make a mistake during any
9. andomly change the code every time you use them and your system will not respond 1f any code is re transmit ted This technology makes code grabbing devices useless Electronic Scan Prevention ESP Your system includes Electronic Scan Prevention ESP which blocks electronic scanner codes preventing unauthorised operation of your system A thief could use an electronic scanner to con tinuously scan through thousands of different transmitter codes n an attempt to find one that will disarm your system Your Maxx system uses ESP technology to render this type of attack useless Interior Light Illumination When the alarm system 1s remotely disarmed the vehicle interior light s will turn on for 30 seconds or until the ignition key is turned on 8 2002 Directed Electronics Inc Passive Immobilisation Immobilisation The built in Dual Circuit Immobiliser will passively arm indicated by a slow LED flash 30 seconds after the ignition is turned off This feature is a Thatcham and EC requirement and therefore is not user programmable To disarm the Immobiliser when it has Passively Immobilised use the remote control to arm and then dis arm the system or turn the ignition on and press the d a button CEEI Z The Valet switch is a small push button switch that allows you to control all of the system s programmable features and enter your override PIN code See User Programmable Features section of thi
10. annel 7 Unassigned Buttons Channel 8 Unassigned d a amp Buttons Channel 9 Unassigned amp Buttons Channel 10 Unassigned Only available with 4 button remote Can be assigned to operate any of the first 6 channels on your Maxx or to control other Avital systems and accessories on other vehicles 2002 Directed Electronics Inc 11 System Operation The alarm can be programmed for active or passive arming Active arming means the alarm is armed using the remote control Passive arming means the alarm will automatically arm itself See the Programming Table for System Features section of this guide Active Arming Arming Press the button for one to two seconds The following will occur m he siren will chirp twice and the indicator lights will flash twice The doors will lock The LED will double flash pause double flash pause etc and the built in Autolmmobiliser will disable two vital engine circuits Requires connection to your vehicle s existing central locking system Passive Arming Arming The Maxx3 has three programmable options relating to passive arming of the alarm A full description of the operation and pro gramming options for the passive arming feature can be found on page 21 Disarming the System if alarm is not sounding Press the button for one to two seconds The following will occur E The siren will chirp once and the indicato
11. d the system from To locate an authorised Avital dealer in your area call our UK office using the number noted in the back of this guide 2002 Directed Electronics Inc 5 Your Warranty E It is necessary to retain your proof of purchase which reflects that the product was installed by an authorised dealer For full details regarding your warranty coverage please refer to the Consumer Warranty section of this guide Remote Controls Controls Included with your system one AviGlo 4 button 10 channel remote and one AviGlo 2 button 3 channel remote Once exposed to light the AviGlo remote control buttons will glow making them visible in the dark The remote control is a miniature transmitter powered by a small 3 volt lithium battery Obstructions electrical or radio inter ference weather conditions window tint or a discharged battery can reduce range Your transmitter is the key to your system and can be used to arm and disarm your alarm lock and unlock your doors open your boot and control optional accessories such as a remote engine starter window roll up and garage door opener Your system can accept up to four AviGlo remote controls Additional remote controls and remote control batteries can be purchased from any authorised Avital dealer or by calling the UK office freephone number noted in the back of the guide This accessory is not evaluated by Thatcham 6 2002 Directed Electronics Inc
12. digit in your PIN Example If your PIN is 2345 press the Valet switch four times Turn the ignition key OFF Turn the ignition key to the ON position Enter the last number in your PIN Press and release the Valet switch the same number of times as the last digit in your PIN Example If your PIN is 2345 press the Valet switch five times Turn the ignition key OFF If you have entered the correct code you will hear two chirps one short and one long Should you hear five rapid chirps the correct code has not been entered Begin entering your PIN from the beginning 2002 Directed Electronics Inc 13 To enter Valet mode now turn the ignition on and press and hold the Valet switch for three seconds until the LED illumi nates constantly To Turn Off Protected Valet Mode 1 Turn your ignition key to the ON position or start the engine The LED will turn off to indicate automatic exit of Valet mode To comply with Thatcham regulations a permanent override mode is not allowed How to Change Your PIN Code Your system PIN Code is located on the back of this guide Should you wish to change this code to a number that is easier to remem ber use the following procedure 1 Write down the new four digit PIN number you wish to use 2 Look at the programming table on page 26 To change the first two digits of your code refer to programming branch number 17 and to change the last two digits refer to pro gramming br
13. emporaneous representations or understandings whether written or oral IN ANY EVENT DEI IS NOT LIABLE FOR THE THEFT OF THE VEHICLE AND OR ITS CONTENTS This warranty is void if the product has been damaged by accident unreasonable use neglect improper service or other causes not arising out of defects in materials or construction This warranty is nontransferable and does not apply to any unit that has been modified or used in a manner contrary to its intended purpose and does not cover batteries The unit in question must be returned to the manufacturer postage prepaid This warranty does not cover labour costs for the removal diagnosis trou bleshooting or reinstallation of the unit For service on an out of warranty product a flat rate fee by model is charged Contact your authorised dealer to obtain the serv ice charge for your unit These systems are a deterrent against possible theft Directed Electronics Inc is not offering a guarantee or insuring against the theft of the vehicle or its contents and disclaims any liability for the theft of the vehicle and or its contents Directed Electronics does not authorise any person to create for it any other obligation or lia bility in connection with this security system TO THE MAXIMUM EXTENT ALLOWED BY LAW ANY AND ALL WARRANTIES ARE EXCLUD ED BY THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE STREAM OF COM MERCE THEREWITH THIS EXCLUSION INCLUDES BUT IS NOT LIMITED TO THE EXCLU
14. for ON Ignition Controlled ON 5 Press d amp button The siren will Lock Unlock chirp once for OFF twice for ON Arm Disarm ON 8 Press button The siren will siren Chirps chirp once for OFF twice for ON Door Ajar Indication ON 13 Press button The siren will chirp once for OFF twice for ON Dual Sensor single 14 Press button The siren will Trigger Mode chirp once for Single twice for Dual Pin Code Digits Factory 17 Press button 1 through 9 1 and 2 selected times to set first digit of PIN code Press button 1 through 9 times to set the second digit of PIN code If you require a 00 Zero zero in the PIN code press d amp buttons at the same time Pin Code Digits Factory 18 Press button 1 through 9 3 and 4 selected times to set third digit of PIN code Press button 1 through 9 times to set fourth digit of PIN code If you require a 00 zero zero in the PIN code press X buttons at the same time 26 2002 Directed Electronics Inc Programming Table for Remote Controls Factory No of Arm Disarm Panic Button 20 Press any remote button s The Two Stage Unlock Channel 1 siren will chirp once for confirmation Accessory Output Button 21 Press any remote button s The for Boot Release Channel 2 siren will chirp twice for confirmation disarmed only Silent Arm Disarm Button 22 Press any remote button s The siren Channel 3 will chirp three times for confirmation
15. ity Unlock Capability If the optional Two Stage Unlock feature was installed press the d a button for one to two seconds and only the drivers door will unlock Within three seconds press the d a button again and the passenger door s will unlock NOTE If you opted to have the Two Stage unlock feature installed then unlocking your vehicle from the drivers door with the key will not unlock the passenger door s They will have to be unlocked manually Sensor Bypass Bypass If you wish to arm the alarm system but leave a window or sun roof open or a pet or passenger inside the vehicle you will need to bypass the Ultrasonic Sensor and any optional sensors by fol lowing the procedure noted below 1 Arm the alarm with the d a or amp buttons 2 At anytime after the alarm system has been armed press the dia and buttons together 3 To indicate sensor s bypass the indicator lights flash once NOTE The next time the alarm system is armed the sensors will be re enabled automatically 14 2002 Directed Electronics Inc Protected Valet Mode Valet Mode You should place your system in Protected Valet Mode whenever your vehicle is being fueled or washed or whenever the passive Immobilisation or arming is not required for a short period The Valet PIN code number for your system is noted on the back of this guide Note To change your PIN code refer to How to Change Your PIN Code sec tion of this guide If the
16. on key is turned ON or the engine is started and will unlock when the ignition key is turned OFF This feature can be programmed ON or OFF See the Programming Table for System Features section of this guide NOTE If this feature is turned on and you need to open a door to let Someone in or out of the car when the ignition is on you can press the d amp button to unlock the doors and again to re lock after the doors have been closed Requires connection to the vehicle s existing central locking system 22 22002 Directed Electronics Inc Long Term Silent Arm Disarm Silent Arm Disarm This feature allows you to completely disable the arm disarm siren chirps until you decide to restore them See the Programming Table for System Features section of this guide Door Ajar Indication Ajar Indication When you remotely arm the alarm system and a door is ajar the siren will chirp twice then three times the indicators will flash the same number of times as the siren chirps This feature pro vides audible and visual indication to prevent battery drain if a door was inadvertently left open See the Programming Table for System Features section of this guide NOTE If your vehicle has an interior light delay this feature will be turned off Dual Sensor Trigger Mode Trigger Mode The system has the facility to add extra sensors such as the 508D Proximity sensor If an additional sensor has been added to the system and
17. one Remote Controlled Chirp Muting E Pressing the amp button for one to two seconds will arm and disarm your system without the siren chirp confirmation Panic Mode m Press and hold down for 3 4 seconds to activate Panic Mode Press d amp to stop panic mode at any time Location of Valet Switch Valet PIN Number 2002 Directed Electronics Inc 31 32 92002 Directed Electronics Inc Health Check l Directed Electronics recommend you return to your installing Avital dealer to have your system checked for correct operation The first check is due one year after the installation date and at yearly intervals thereafter NOTE There may be a small charge incurred for this service Signed Dated Signed Dated Signed Dated Signed Dated Signed Dated Signed Dated 33 2002 Directed Electronics Inc driven to excel LYrected ELECTRONICS INC Directed Electronics Inc Vista CA 92083 www directed com Making changes to the existing security system will invalidate the certificate of installation Should any fault with the sys tem occur please contact your installing Avital dealer as soon as is convenient Your system Pin Code is Place Pin Code sticker here E amp OE specification is subject to change without notice Some vehicles require optional parts wiring and a few are incompatible with some features For questions regarding your Maxx system contact
18. onnected to a particular zone Often two or more inputs may share the same zone 30 2002 Directed Electronics Inc Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet O ns ssa O Quick Reference Guide Arming EH Toarm press When the system arms you will hear two short chirps and the indicator lights will flash twice Disarming E To disarm press You will hear a chirp and the indicator lights will flash once Siren Silencing m or siren silencing press on your transmitter whist the siren is sounding and the siren will stop sounding To completely disarm the security system press again Disarming Without a Transmitter m Turn on the ignition Press the Valet switch the number of times that cor responds with the first number of your Valet code Turn the ignition off then back on Press the Valet switch the number of times that corre sponds with the second digit of your Valet code Turn the ignition off then back on Press the Valet switch the number of times that corre sponds with the third digit of your Valet code Turn the ignition off then back on again Press the Valet switch the number of times that corre sponds with the fourth digit of the Valet code Turn the engine off If you have entered the proper code the alarm will emit two chirps and then turn off Five chirps indicate the wrong code has been entered Re enter your Valet code starting at digit
19. ory preset not to lock the doors when the alarm passively arms unless Auto rearm and lock is programmed on to prevent the keys and remote from being locked in the vehicle If you prefer you can easily program the alarm to automatically lock the doors every time the alarm passively arms See the Programming Table for System Features section of this guide Requires connection to your vehicle s existing central locking system 2002 Directed Electronics Inc 21 Auto Rearm and Lock and Lock When Auto rearm and lock is used in conjunction with the passive arming feature 1 e both are turned ON the following will occur m If after driving you turn the ignition off and exit the vehicle by opening and closing a door the system will passive arm but NOT lock the doors in case you have left your keys inside the car m If the alarm is disarmed or AutoImmobilised only and you open and then close a door the system will passive arm but NOT lock the doors again in case you left your keys inside m If you disarmed the alarm but did not open a door the sys tem will auto rearm and lock the doors As you did not open a door the system assumes you are outside the vehicle and the keys are not inside Requires connection to the vehicle s existing central locking system Ignition Controlled Door Lock Unlock For the ultimate in security and convenience the system is pro grammed to automatically lock your doors when the igniti
20. part of this procedure then simply turn off the ignition and begin the sequence again The system will revert to the original code 2002 Directed Electronics Inc Diagnostics LED System Status Indicator The LED on your vehicles dashboard or centre console will inform vou of the system status LED Off oystem is disarmed On In Valet mode Slow Flash Passive Immobilised only Double Flash oystem is armed and Immobilised Triple Flash More than three consecutive incorrect Valet codes have been entered system ignores Valet switch for 2 minutes Flashing in Cycles See Specific Zone Intrusion Identification chart on page 22 Rapid Flash Passive arming countdown Previous Intrusion Alert Intrusion Alert If the vehicle had been tampered with and the alarm has been triggered the siren will chirp three times upon remote disarm instead of the usual single chirp Specific Zone Intrusion Identification If you received the Previous Intrusion Alert confirmation three chirps upon remote disarm when you enter the vehicle and turn the ignition ON the LED will flash in cycles to specifically identi fy which zone has triggered the alarm The flash cycle will be repeated two more times giving three cycles in total 2002 Directed Electronics Inc 19 LED ne OO Three Flashes Optional Sensor 2 Four Flashes Door Trigger Five Flashes Boot Bonnet Trigger Six Flashes Closed Circuit Trigger Seven Flashes Ul
21. r lights will flash once The doors will unlock The interior lights will turn on 12 2002 Directed Electronics Inc for 30 seconds or until the ignition s turned on The immo bilised engine circuits will be re enabled to allow you to start your car The LED will turn off Requires connection to your vehicle s existing central locking system Disarming the System if alarm is sounding Press the d a button for 1 2 seconds This will silence the siren only It will not disarm the system or unlock the doors A second press of the button for one to two seconds is required to fully disarm the system Requires connection to your vehicle s existing central locking system Silent Arm Disarm Arm Disarm Pressing the amp button for one to two seconds will arm and dis arm your system the same as the d a button except without the siren chirp confirmation Remote Panic Panic When activated the siren will sound and the indicator lights will flash If you are outside the vehicle with the ignition key OFF the doors will unlock To Activate 1 Press the d a button for three to four seconds 2 The siren will sound and the indicator lights will flash 3 If the ignition key is OFF the doors will unlock 2002 Directed Electronics Inc 13 To De activate 1 Press the d a button for one to two seconds 2 The siren will shut off and the indicator lights will stop flashing Two Stage Unlock Capabil
22. r which monitors your vehicle and controls all sys tem functions Immobiliser Circuit A vital circuit that prevents your vehicle from starting when the unit is Immobilised or armed The Maxx 3 Immobilises two independent circuits for double the security and protection Input A physical connection to the system An input can be pro vided by a sensor pinswitch or by existing systems in the vehicle such as ignition or courtesy lights 2002 Directed Electronics Inc 29 LED A red light mounted at a discretionary location inside the vehicle It 1s used to indicate the status of your system Transmitter A hand held remote control which operates the var ious functions of your system Trigger or Triggered Sequence This is what happens when the alarm goes off or trips The triggered sequence of your system consists of the siren sounding and indicators flashing Valet Switch A small push button switch mounted at a discre tionary location inside the vehicle It is used to override the built in Immobiliser when a transmitter has been lost or damaged and to enter Valet Mode Warning Zone Response If a dual zone sensor is added to the system and the light touch or outer zone trigger is activated the system will generate the warning zone response This consists of several seconds of siren chirps Zone A zone is a separate input that the alarm can recognise as unique Each input to the system is c
23. s guide This switch can only be controlled in conjunction with your ignition key NOTE Make sure the dealer has shown you where the Valet switch is located You will need to disarm the system with the Valet switch in the event of a lost or stolen remote control Keyless Entry in Valet Mode While the system is in the Valet mode you can still use your remote control to lock and unlock the doors as well as activate any optional accessories such as boot release or remote engine Starter Ultrasonic Sensors ltrasonic Sensors Your Maxx security system incorporates two Ultrasonic sensors which are most commonly mounted at the top of the A pillars fac 2002 Directed Electronics Inc 9 ing the rear of the vehicle These sensors detect movement inside the vehicle by sensing air disturbance They should trigger the alarm if a thief gained access to the interior of your vehicle Instant Remote Control Code Deletion In the event of a lost or stolen remote control all remote controls can be erased from the systems memory preventing unauthorised system operation See the Programming Table for Remote Controls section of this guide One Step Remote Control Code Learning Your system allows you to add new remote controls in one step See the Programming Table for Remote Controls section of this guide Alarm State Memory State Memory If your vehicle battery is disconnected and later reconnected the system
24. system was armed and a thief were to break into your vehi cle and begin entering codes at random in an attempt to disarm the alarm the system will lock out indicated by a triple flash sequence of the LED and begin sounding the siren for two min utes During this period the system will ignore further attempts to enter the code Even a correct code entry will be ignored The siren can be silenced and the system disarmed by pressing the la or button on the remote control two times NOTE The PIN number noted on the back of this guide is your emergency override code Therefore Do NOT leave the guide inside the vehicle for a thief to find To Turn On Protected Valet Mode 1 Turn the ignition key to the ON position 2 Within 10 seconds enter the first number in your PIN Press and release the Valet switch the same number of times as the first digit in your PIN Example If your PIN is 2345 press the Valet switch two times 2002 Directed Electronics Inc 15 10 11 TZ 16 Turn the ignition key OFF Turn the ignition key to the ON position Enter the second number in your PIN Press and release the Valet switch the same number of times as the second digit in your PIN Example If your PIN is 2345 press the Valet switch three times Turn the ignition key OFF Turn the ignition key to the ON position Enter the third number in your PIN Press and release the Valet switch the same number of times as the third
25. trasonic Sensor Eight Flashes Ignition Trigger Automatic Malfunction Override In the event of an active sensor or trigger input when the alarm is remotely armed a series of chirps and Indicator light flashes will alert you Interpreting Chirps and Flashes 1 chirp 1 flash Disarming of the alarm 2 chirps 2 flashes Arming of the alarm 3 chirps 3 flashes Disarmed and there was an intrusion attempt 2 chirps and flashes Armed and a door is ajar then 3 more chirps and flashes 2 chirps and flashes Armed and there is a sensor input active then 4 more chirps and flashes automatically bypassed 2 chirps and flashes Armed and there is a boot bonnet or then 5 more chirps and flashes closed circuit trigger input active automati cally bypassed 20 2002 Directed Electronics Inc User Programmable Features Passive Arming Arming Turn the ignition key OFF exit the vehicle and close the doors When the interior lights turn off the LED will begin flashing rap idly to indicate the alarm has begun it s passive arming count down After 60 seconds the siren will chirp twice the indicator lights will flash twice and the system s LED will begin the double flash sequence explained in the Active Arming section NOTE The alarm can be actively armed with the or amp button on the remote control at any time during the passive arming countdown Passive Arming With Door Lock The system is fact
26. will automatically return to its last state before power was removed whether it was armed disarmed or in Valet Mode For example if a mechanic were to disconnect the battery while the alarm was disarmed or in Valet Mode the alarm will not trigger when the battery is reconnected If power is removed and then restored while the alarm is armed the systems battery back up siren will instantly sound the indicator lights will flash and the Dual Circuit Immobiliser will still be enabled preventing the vehi cle from being started 10 2002 Directed Electronics Transmitter Functions Accessory Outputs and Button Assignments These outputs allow you to add optional remote controlled acces sories to your system such as a remote engine starter boot release window roll up garage door opener or fuel filler door release To activate your optional accessories press the correspon ding remote control buttons shown below You can assign any remote control function to any button sequence See Programming Table for Remote Controls section of this guide Button Channel Assignment Feature gt gt gt Button Channel 1 Arm Disarm Panic Two Stage Unlock X Button Channel 2 Pulsed Accessory Output Disarmed Only Button Channel 3 Silent Arm Disarm amp Button Channel 4 Timer Controlled Output 9 Buttons Channel 5 Pulsed Latched Accessory Output d a Buttons Channel 6 Sensor Bypass d a Buttons Ch
27. y is disconnected Bonnet Lock Prevents the vehicles bonnet from being opened without a key keeping thieves away from the sys tem s siren the battery connections and other components under the bonnet Field Disturbance Sensor An invisible dome of coverage is established by installing the 508D radar sensor Your system can react to any intrusions into this field with the full trig gered sequence Remote Starter A remote engine starting system designed for fuel injected automatic transmission vehicles The 551T is activated by pressing a spare button on your remote control NOTE The Remote Starter has not been evaluated by Thatcham 2002 Directed Electronics Inc m Electric Boot Release The accessory output of the system can operate a factory electric release for the vehicle s boot or hatch Although the on board circuit can control some elec tric factory releases an optional relay is usually required If the factory release is not electric activated Directed s 522T boot release solenoid can often be added E Electric Window Control Automatic electric window control is provided with the 529T and 530T systems These can oper ate electric windows and can roll them up automatically when the system is armed roll them down or both up and down Glossary of Terms Control Unit The brain of your system Usually hidden under neath the dash area of the vehicle The control unit houses the microprocesso
28. your authorised Avital dealer or the Directed Electronics UK office Directed Electronics UK Office Unit 4 Boundary Business Court 92 94 Church Road Mitcham Surrey CR4 3TD Sales and Customer Support Freephone 0800 929949 e Fax 0208 6468430 2002 Directed Electronics Inc All rights reserved Avital is a division of Directed Electronics Inc G840003 4 02 PATO nynyn id Mm ZA US US VU REGISTRATION NO O O 8 4 O 1 Directed is an ISO 9001 registered company Directed is committed to delivering world class quality products and services that excite and delight our customers
Download Pdf Manuals
Related Search