Directed Electronics 3000 Automobile Alarm User Manual
Contents
1. 11 auxiliary channel bypass 12 valet mode 12 remote valet mode 13 instant auto arming bypass 14 nuisance prevention circuitry 14 multiple event total recall 15 battery back up siren 15 2005 directed electronics all rights reserved diagnostics a a o onanan 16 arming diagnostics 16 disarming diagnostics 17 arm disarm diagnostic chart 17 table Of zones sce ew nse a 18 high frequency 19 rapid resume logic 19 power saver mode 20 system sensors and adjustments 20 programming options 21 manual programming INS rUCtIONS 24 228 tun acnde 22 user selectable features 24 user selectable features descriptions column one 24 user selectable features descriptions column two 26 user selectable features descriptions column three 27 pin programming 29 glossary of terms 31 security amp convenience expansions x ccvew eres auew ae 32 quick reference guide 33 what is included e One control module siren with built in Tilt sensor and 24 pin main wiring harness attached e One Mini Blue status LED One 2 button Valet switch One in key 2 button remote One 3 button remote Two Merlin decal s e This Owner s Guide e Warranty Card important information sss Congratulations on the purchase of your2. Arm 1 3 sec pause 1 System armed with zone active and bypassed Disarm 2 System disarmed Disarm 4 System disarmed with tamper alert High Security 1 System silenced but still armed and Disarm all zone inputs are inactive and siren on monitored High Security 3 System silenced but still armed and Disarm a zone is still active and bypassed siren on Disarm 5 System disarmed with a zone in NPC Refer to the table of zones to identify the last zone triggered 2005 directed electronics all rights reserved 17 table of zones The zone number is the number of LED flashes used by the system to identity a specific input The standard input assignments are listed below along with spaces to write in any optional sensors or switches you have had installed If a Warning Zone response is triggered the LED will not report it Zone Number Dealer Installed of LED Flashes Description Options 1 Tilt Sensor Built in Tilt Sensor 2 Auxiliary sensor 1 input 3 Auxiliary sensor 2 input 4 Normally Closed input from protective switch 5 Optional switch input 6 Ignition Input 7 12 V Power interruptions anti code grabbing ACG ss This unit features Anti Code Grabbing ACG with Random Code Encryption This means the receiver and remotes each use a mathemati cal formula called an algorithm to change their code each time the remote is used This technology has been developed to increase the secu rity of the unit The control unit kn
3. Circuitry on off Inhibits false alarming if a protective zone repetitively alarms Remote Valet on off Reset settings to default except for PIN code New remote learn features Allows programming individual transmitter channels to custom configurations Refer to User Selectable Features Descriptions Column Three e Clear all Remotes Removes all remote controls from memory 2005 directed electronics all rights reserved 21 manual programming instructions It is a good idea to document changes by taking note of all feature changes made in programming mode To enter the User Selectable Features programming 22 Ignition on Turn the ignition to the on run position or start the engine Enter PIN Your PIN code FOR EXAMPLE To enter a PIN code of 4301 Press BE four times then E once This enters the digit 4 then B three times then E once This enters the digit 3 and then f once This enters a O as there was not a previous digit entered with then once and then once This enters the final digit 1 Hold Chirp Release After entering the PIN code press and hold k until a chirp is heard and the LED turns on then release the button You have now entered the feature selec tion position of the User Selectable Features grid Column select Press and release the same number of times as the desired column After a pause the siren will chirp the same number of tim
4. Blue light mounted somewhere on the motorcycle It is used to indicate the status of your system It is also used to report triggers and faults with the system Tilt Sensor A sensor integral with the control module which senses if the angle of the motorcycle has changed Remote Hand held transmitter which operates the various functions of your system Trigger or Triggered Sequence This is what happens when the alarm goes off or trips The triggered response of your system consists of the siren sounding and indicators flashing for 30 seconds Valet Switch A small two button switch mounted somewhere on the motorcycle It is used to override the alarm when a remote is lost or damaged or to enter or exit Valet mode and for system programming Zone A zone is a separate input that the alarm can recognize as unique Each input to the system is connected to a particular zone 2005 directed electronics all rights reserved 31 security amp convenience expansions lt Here we have listed only some of the many expansion options avail able Please contact your dealer for a complete list of all the options available to you Field Disturbance Sensor An invisible dome of coverage is established by installing the 508D radar sensor Your security system can then react to any intrusions on the perimeter of the field with a warnaway response and if anyone were to intrude inside the dome the full alarm would sound Ideal for warnin
5. Buttons When pressed together these buttons disable the on board control module tilt sensor and any optionally installed sensors standard configuration for 3 button remote aA Button The arming disarming and panic functions are controlled by this button 2005 directed electronics all rights reserved 5 3 Button An optional accessory convenience or expansion function that you have added to your system can be activated by pressing this button K Button Silent arm and disarm is controlled by this button dQ and XK Buttons When pressed together these buttons disable the on board control module tilt sensor and any optionally installed sensors and 36 Buttons Remotely enters or exits Valet using your system The buttons used in the instructions in this manual correspond to the standard remote configuration If your remote has been custom con figured the icons on your remote buttons may not correspond to the indicated functions arming You can activate or arm the system by pressing maa on your remote for one second When the system arms you will hear one short siren sound or chirp and see the parking lights flash once The LED will illu minate steadily 6 2005 directed electronics all rights reserved While the system is armed the LED status indicator will flash approxi mately once per second showing that the system is actively protecting your vehicle If you hear more than one chirp w
6. Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet The company behind this system is Directed Electronics Since its inception Directed Electronics has had one purpose to provide consumers with the finest vehicle security and car stereo products and accessories available The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology Directed is ISO 9001 registered Quality Directed Electronics products are sold and serviced throughout North America and around the world Call 800 274 0200 for more information about our products and services Directed Electronics is committed to delivering world class quality products and services that excite and delight our customers Liixected E LECTRONICS Vista CA 92081 www directed com 2005 Directed Electronics All rights reserved G225T 10 05
7. and address e Authorised dealer s company name and address e Type of alarm installed e Year make model and colour of the vehicle e Vehicle registration number e Vehicle identification number e All security options installed on vehicle e Installation receipts trademarks and copyrights lt Bitwriter Clifford Code Hopping Directed Doubleguard ESP FailSafe Ghost Switch Learn Routine Nite Lite Nuisance Prevention Circuitry NPC Revenger Silent Mode Soft Chirp Stealth Coding Stinger Valet Vehicle Recovery System VRS and Warn Away are all Trademarks or Registered Trademarks of Directed Electronics il 2005 directed electronics all rights reserved table of contents _ limited lifetime consumer Wafanye wane Qeueunre neuen sks i trademarks and copyrights ii table of contents 1 what is included 2 important information 2 your warranty ties tet eae ae 3 remote configurations 4 standard configuration for in key 2 button remote 5 standard configuration for 3 button remote 5 using your system 6 PUIG 06 5 Sh AN ah NS 6 disarming so 6 5 sinned ued Geode 8 disarming without a remote 8 auto immobilisation 9 remote siren silencing 9 remote chirp muting 3 button remote only 10 remote sensor disable 11 remote start sensor bypass
8. code with the Valet switch O If any other input is activated when in sleep mode the system will wake up and trigger the alarm immediately system sensors and adjustments Your system was installed with an integral Tilt sensor Optional sensors such as the 504D Double Guard Shock sensor or 508D Dual Zone Proximity sensor may also have been installed For adjustments to all sensors options please return your motorcycle to the installing Directed dealer 20 2005 directed electronics all rights reserved programming options esses Programming options control what your system does during normal operation and require few or no additional parts However some may require additional installation labor Following is a list of the program settings with the factory settings in bold e Autoarming on or autoarming off of the alarm Automatic arming 30 seconds after ignition turned off e Arming disarming confirmation siren chirps off loud or quiet The siren arm disarm chirps can be either full volume 6 decibels quieter or turned off completely Panic mode on off e Siren duration 30 60 90 seconds Set PIN code Allows you to enter your own PIN code over writing the factory PIN code e Siren tones The output of the siren consists of six different tones in sequence Any of these tones can be eliminated result ing in a unique easily identifiable siren sound NPC Nuisance Prevention
9. etc the unit will chirp once when arming and then once more five seconds later This is called Bypass Notification Refer to the Arm Disarm Diagnostic Chart for bypass notification details You are able to see exactly which zone is causing the bypass notification by disarming the system and turning the ignition on The zone will be report ed by flashing the active zone 5 times See the Table Of Zones The security system will ignore the input that was active when the sys tem was armed until the input goes away 3 seconds later the system will monitor that input normally For example if the protective switch is active you will hear one Bypass Notification chirp the protective switch is bypassed from the alarm system Once the protective switch is reset then 3 seconds later the system resumes normal monitoring of this switch 16 2005 directed electronics all rights reserved disarming diagnostics Extra disarm chirps are the Tamper Alert If four chirps are heard when disarming the system was triggered in your absence If four chirps are heard the LED status indicator will indicate which zone was triggered when the ignition is turned on and will repeat 5 times refer to the Arm Disarm Diagnostic Chart and Table of Zones section The system will retain this information in its memory Refer to the Multiple Event Total Recall section of this guide arm disarm diagnostic chart Action No of Chirps Description Arm 1 System armed
10. not auto arm note The system will revert to normal auto arming when the system sees the ignition on for at least three seconds and then turned off or the system is armed and disarmed with the remote During auto arming bypass the system will not auto activate the acces sory output when using the remote to arm the system nuisance prevention circuitry Your system has Directed s Nuisance Prevention Circuitry NPC It pre vents annoying repetitive trigger sequences due to faulty switches or environmental conditions such as thunder jackhammers airport noise etc Example If the alarm triggers three times within a 60 minute period and each time the same sensor or switch triggers the alarm NPC will interpret those triggers as false alarms After the third trigger NPC ignores or bypasses that sensor or switch along with any other sen sors or switches sharing the same zone for 60 minutes If the bypassed sensor tries to trigger the system while it is being bypassed the 60 minute bypass period will start over This ensures that a sensor that continually triggers will remain bypassed 14 2005 directed electronics all rights reserved note Arming and disarming the system does not reset this function The only ways fo reset a bypassed zone are for it to not trigger for 60 min utes or fo turn on the ignition If testing your system it is important to remember that the NPC programming can cause zones fo be bypas
11. zones will reset when disarmed note Sensor disable can be performed at any time after the alarm has been armed remote start sensor bypass When the system sees a command to remote start the motorcycle it bypasses sensor zones and will continue to bypass these zones until the remote start shuts down Note Additional installation options required for Remote Start opera tion See your Directed Authorised dealer for details 2005 directed electronics all rights reserved 11 auxiliary channel bypass All alarm sensor inputs will be bypassed while a pulsed or timed auxil lary output Is active panic mode If you are threatened near your vehicle you can attract attention by triggering the system with your remote Just press aa for two sec onds to enter Panic Mode The siren will sound and the indicator lights will flash for the programmed duration 5 minutes maximum To stop Panic Mode at any time press aa on the remote again valet mode You can prevent your security system from automatically arming by using Valet Mode This is very useful when washing the motorcycle for example In Valet Mode the security system will not arm even with the remote but any accessory functions will continue to work normally To enter Valet Mode 1 Turn the ignition On 2 Enter the PIN code as described in the Disarming Without a Remote section 3 When you enter the last digit continue to hold the button for at least thre
12. Merlin Owner s Guide limited lifetime consumer warranty For a period of one calendar year from the date of purchase of this auto security device Directed Electronics promises to the ORIGINAL PURCHASER to repair or replace with a com parable reconditioned model free of cost any electronic control module which proves to be defective in workmanship or material under normal use SO LONG AS THE SYSTEM WAS SOLD INSTALLED AND SERVICED BY A PROFESSIONAL AUTO INSTALLER AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS ORIGINALLY INSTALLED If warranty service is necessary you must have a clear copy of your sales receipt containing all of the information shown on the follow ing page After the first calendar year from the date of purchase of this auto security device Directed Electronics promises to the ORIGINAL PURCHASER to repair or replace with a comparable reconditioned model any electronic control module which proves to be defective in work manship or material under normal use FOR A CHARGE OF 45 00 SO LONG AS THE SYSTEM WAS SOLD INSTALLED AND SERVICED BY A PROFESSIONAL AUTO INSTALLER AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS ORIGINALLY INSTALLED If warranty service is neces sary you must have a clear copy of your sales receipt containing all of the information shown on the following page This warranty contains the entire agreement relating to warranty and supersedes all previous and contemporaneous representations or un
13. OF MERCHANTABILITY AND OR ANY AND ALL WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND OR ANY AND ALL WARRANTY OF NON INFRINGEMENT OF PATENTS IN THE UNITED STATES OF AMERICA AND OR ABROAD NEITHER THE MANUFAC TURER OR ANY ENTITIES CONNECTED THEREWITH SHALL BE RESPONSIBLE OR LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL DAMAGES INCIDENTAL DAMAGES TOWING REPAIR REPLACEMENT DAMAGES FOR LOSS 2005 directed electronics all rights reserved i OF TIME LOSS OF EARNINGS COMMERCIAL LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE MANUFACTURER DOES OFFER A LIMITED WAR RANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE Some states do not allow limitations on how long an implied warranty will last or the exclusion or limita tion of incidental or consequential damages This warranty gives you specific legal rights and you may also have other rights which vary from state to state IMPORTANT NOTE This product warranty is automatically void if its date code or serial number is defaced miss ing or altered This warranty will not be valid unless you have completed the warranty card and mailed it to Directed Electronics within 10 days after purchase to the address listed on the warranty registration card Make sure you have all of the following information from your dealer A clear copy of the sales receipt showing the following e Date of purchase e Your full name
14. This enters the digit 4 Then three times Then once This enters the digit 3 d Then once This enters a O as there was not a previous digit entered with BE Se oY ok ae oe 8 2005 directed electronics all rights reserved 8 Then B once 9 Then once This enters the final digit 1 auto immobilisation Immobiliser circuits automatically activate after 30 seconds Auto immobilisation sequence 1 Turn ignition off or disarm alarm 2 After 30 seconds the systems Immobilisation circuits activate and engage the starter and engine interrupts 3 LED flashes at Y2 normal speed Disarm the system when immobilised Use one of the following methods to turn off auto immobilisation e Turn ignition on and press the aa button of the trans mitter Arm the alarm and then disarm the alarm e Turn the ignition on and enter the system Valet PIN code remote siren silencing Remote siren silencing is a feature that makes it possible to silence and reset the system when it is triggering without disarming the system If the system is triggered and the siren is sounding press aa on the remote to stop the trigger and return the unit to the armed state The system will not disarm but rather reset This prevents you from dis abling the system should you wish to silence it without visually check ing the vehicle After resetting the system press aa again to disarm the system 2005 di
15. count down is indicated by the system LED rapid flashing After the first five seconds you will hear one chirp and the indicators will flash The system will arm 25 seconds later e Off The transmitter must be used to arm the system chirps off loud quiet e Off Chirps will not sound when arming disarming the sys tem with the exception of arm disarm diagnostic chirps and programming chirps e Loud Chirps will sound when arming disarming the system at full volume e Quiet Chirps will sound when arming disarming the system but at a lower volume than normal with the exception of arm disarm diagnostic chirps and programming chirps panic on off Allows the remote to activate Panic Mode The siren will sound for 30 seconds e On The system will enter Panic Mode if the arm disarm but ton is pressed for more than 2 seconds e Off Panic Mode is disabled siren duration 30 60 90 e The system will sound the alarm for the programmed dura tion 30 60 90 seconds during an alarm trigger or when the system is put into panic mode 2005 directed electronics all rights reserved 25 user selectable features descriptions column two set pin code e This feature allows you to change your personal PIN code For more information please refer to the PIN Programming section of this guide Factory default PIN number is 2 select siren sounds This feature allows you to select which siren sounds will be pla
16. derstandings whether written or oral IN ANY EVENT DIRECTED ELECTRONICS IS NOT LIABLE FOR THE THEFT OF THE VEHICLE AND OR ITS CONTENTS This warranty is void if the product has been damaged by accident unreasonable use neglect improper service or other causes not arising out of defects in materials or con struction This warranty is nontransferable and does not apply to any unit that has been mod ified or used in a manner contrary to its intended purpose and does not cover batteries The unit in question must be returned to the manufacturer postage prepaid This warranty does not cover labor costs for the removal diagnosis troubleshooting or reinstallation of the unit For service on an out of warranty product a flat rate fee by model is charged Contact your authorized dealer to obtain the service charge for your unit These systems are a deterrent against possible theft Directed Electronics is not offering a guar antee or insuring against the theft of the automobile or its contents and disclaims any liability for the theft of the vehicle and or its contents Directed Electronics does not authorize any per son to create for it any other obligation or liability in connection with this security system TO THE MAXIMUM EXTENT ALLOWED BY LAW ANY AND ALL WARRANTIES ARE EXCLUDED BY THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE STREAM OF COMMERCE THEREWITH THIS EXCLUSION INCLUDES BUT IS NOT LIMITED TO THE EXCLUSION OF ANY AND ALL WARRANTY
17. e seconds then release The LED status indicator will light up and EJE 12 2005 directed electronics all rights reserved remain on if Valet Mode has been entered The LED status indicator will light steadily if you are entering Valet Mode Note The LED will turn off when the ignition is ON To exit Valet Mode 1 Turn the ignition On 2 Enter your PIN code as described previously 3 When you enter the last digit the LED will light up contin ue to hold the F button 4 The system will exit Valet mode and the status LED indicator will extinguish NOTE If One time Valet is programmed On by your installer the system will auto matically exit Valet mode the next time the ignition is turned on remote valet mode The operations described in this section refer to remote buttons Remember the buttons used in all the instructions in this guide corre spond to the Standard Configuration for the 3 button remote This may not be how your remote Is set up To enter Valet Mode press and 3 e simultaneously The LED Status indicator will illuminate continuously if you are entering Valet Mode or will turn off if you are exiting Valet Mode 2005 directed electronics all rights reserved 13 instant auto arming bypass This will bypass the auto arm feature once only 1 With the key turn the ignition on then off within two seconds 2 The siren will chirp once to confirm auto arming bypass 3 The system will
18. es as the selected column for confirmation e g 3 chirps means column 3 of the features is selected Feature select Press and release k the same number of times as the desired row The siren will chirp with each press The feature can now be changed using the remote control 2005 directed electronics all rights reserved Feature change Press the aa button on the remote If the system chirps once the feature has just turned off or switched to the first setting in the grid slot for this feature if the system chirps twice the feature has just turned on or switched to the second setting in the grid slot If the feature has more than two settings continue pressing the aa on the remote to toggle through the settings e g if the feature has 1 through 5 settings the system will chirp 1 through 5 times for each setting selected If you continue to press and release the remote the feature setting will wrap back around to the first setting again e g if the feature has 3 settings you will hear 1 chirp 2 chirps 3 chirps 1 chirp 2 chirps etc To advance to another feature in the same column press k the same number of times as the desired feature with in 60 seconds to change a feature in a different column begin at step 5 by entering the column number first and then the feature select in step 6 note Refer to the Feature Descriptions sections of this guide for impor tant notes and descriptions of the system features a
19. g people away from the motorcycle Shock Sensor The 504D dual stage shock sensor can be installed to provide warn away and alarm protection for your motorcycle if impacts are detected Remote Start The 561T remote start system to provide engine warm up and battery recharging 32 2005 directed electronics all rights reserved Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet remote functions E 3 button 2 button remote remote Arm Disarm Panic y ala Accessory Output XK K Silent Arm Disarm KK N A Sensor Disable d a K d a K Remote Valet k KK N A E Transmit Silent Arm Disarm to delete the arm disarm chirps for one operation only E Transmit Sensor Disable once to bypass the sensor warn away chirps twice to bypass sensors entirely Note The system must be armed first system disarm To disarm the system without a transmitter turn the key to the ON position and enter your PIN code valet mode entry To enter Valet Mode without a transmitter turn the key to the ON position and enter your PIN code Continue to hold _ on the Valet switch for five seconds pin code entry On the Valet switch press the number of times corresponding to the first digit of your PIN then press _ once Press _ to enter a zero Repeat this for each digit of your PIN code There is a space provided below to note your pin code for future reference
20. hen arming refer to the Diagnostics section of this guide These extra chirps confirm a malfunc tion autobypass The security system also can be programmed to arm itself automatically without a remote called passive arming If the system is programmed for passive arming it will automatically arm 30 seconds after the ignition is turned off Whenever the system is in its 30 second passive arming countdown the siren will chirp once and the lights will flash once five seconds after countdown has commenced This is indi cated by the rapid flash from the status LED The system is not actually armed at that point The system arms after the 30 second countdown has elapsed but the siren will not chirp The early chirps provide you with a 25 second warning prior to arming note If one of the zone 4 or 5 switch inputs is active or the ignition is on the system will not passively arm Additionally if one of these switches is activated or the ignition is turned on the countdown will cease then begin again when the input is removed When armed your vehicle is protected as follows The LED will flash as a visible theft deterrent e Ifthe tilt sensor detects the motorcycle is being moved in an attempt to steal it the system will immediately trigger the siren and flash the indicator lights This sensor is capable of independently learning the bike s ini tial angles of vertical and horizontal inclination each time it is parked ensuring
21. nd programming Exit programming To exit programming mode turn the igni tion off or wait 60 seconds without pressing the Valet but ton The siren will chirp three times to indicate programming mode has been exited After you change a feature setting the feature counter is reset to zero Hence to change another feature in the same column you must press the button the same number of times as indicated in the chart 2005 directed electronics all rights reserved 23 user selectable features E e Add new remote Set PIN code New remote learn autolearn arm disarm only Auto arm Select siren New remote learn on off sounds accessory output Chirps NPC on off New remote learn off loud quiet silent mode nyse sk Panic Remote valet New remote learn on off on off remote valet F Reset to default Siren Duration except transmitter Now remon learn 30 60 90 seconds and PIN code sensor disable 6x sk Not used Not used Clear all remotes from memory user selectable features descriptions column one add new remote for 2 button in key and 3 button remotes only e Auto learn new remote controls to the system one at a time in the standard button configuration For more infor mation refer to Note 1 in Programming Notes section 24 2005 directed electronics all rights reserved auto passive arm on off On When the system sees the ignition turn off it will begin a 30 second countdown before arming itself The
22. nnel programmed into this feature will arm disarm the system but the siren will not chirp remote valet on off e The remote channel programmed into this feature will make the system enter exit valet mode sensor disable e The remote button programmed for this feature will make the system bypass the sensors for one arming cycle only On the next arming cycle zones 1 2 and 3 will be reinstated clear all remotes e This feature will erase all remote codes from the system memory This feature is convenient for erasing any remotes that have been lost stolen or incorrectly programmed into the system e After entering this feature press the aa button on a remote that is programmed to the system the siren will chirp twice to indicate that all remotes have been erased from memory 28 2005 directed electronics all rights reserved pin programming A PIN code can have one to four digits each digit can be from 0 9 note A PIN code cannot begin with a zero Programming Procedure 1 Enter the feature location column 2 row 1 in the user selectable programming grid Immediately press and release LJ of the Valet switch Select each digit by pressing 1 9 times and then press 5 to enter the number into the system To enter a zero press LJ only To program a PIN code of 1032 A Press and release x once and LJ once You will hear one chirp B Press and release a once You will not hear a chirp after
23. ows what the next codes should be 18 2005 directed electronics all rights reserved high frequency eee Your system transmits and receives at 433 MHz This provides a cleaner spectrum with less interference and a more stable signal rapid resume logic eeseses ssSsS This security system will store its current state to non volatile memory If power is lost and then reconnected the system will recall the stored state from memory This means if the unit is in Valet Mode and the bat tery is disconnected for any reason such as servicing the car when the battery is reconnected the unit will still be in Valet Mode This applies to all states of the system including arm disarm autoimmobilised and Valet Mode 2005 directed electronics all rights reserved 19 power saver mode s lt lt isS e When in Valet mode the LED will turn off 1 hour after enter ing Valet mode e After 24 hours in the armed state the LED will decrease the flash rate to 4 the normal rate after 48 hours it will decrease to 4 the normal rate e After 96 hours of no activity arm disarm or alarm trigger the alarm enters sleep mode The alarms receiver and LED turn off to save as much battery power as possible The system is drawing next to no current in this mode O To exit sleep mode turn the ignition on and the siren will chiro 10 times 5 seconds before the siren sounds Disarm the system with the remote or by entering the PIN
24. programming a zero C Press and release k three times and then press once You will hear three chirps D Press and release k two times and then press once You will hear two chirps Wait for two siren chirps after a five second pause or five seconds after the last digit has been entered if using less than four digit code number Turn off the ignition the siren will chirp three times The programming mode is now exited 2005 directed electronics all rights reserved 29 PIN Code Confirmation Procedure Begin this procedure within 15 seconds of finishing the programming sequence or the new code will not be set 1 Turn on the ignition 2 Enter the new PIN code 3 Press and hold LJ for three seconds e LED turns on New PIN code is learned and program ming is complete e LED stays off New PIN code is not learned and the sys tem reverts to the old PIN code Repeat the program ming sequence 30 2005 directed electronics all rights reserved glossary of terms ees Control Unit The brain of your system hidden somewhere on the motorcycle where it is difficult for a thief to access It houses the micro processor which monitors your vehicle and controls all of the system s functions The Merlin 3000 control unit houses the battery backup siren and Tilt sensor Input A physical connection to the system An input can be provided by a sensor switch or through an existing system on the motorcycle LED
25. rected electronics all rights reserved 9 When you remote siren silence the siren will either chirp 1 or 3 times 1 chirp indicates that the system is still armed and that all zones are inactive and being monitored 3 chirps indicate that the system is still armed and that at least one zone Is still active and being bypassed NOTE If 3 chirps sound the input that is bypassed will remain bypassed until the activation ceases remote chiro muting 3 button remote only To temporarily turn off the arm or disarm chirps use remote chirp mut ing Simply press 3 SK on the remote 3 button remote only and the confirmation chirp s will be eliminated for that one operation only The parking lights will flash to confirm the arm disarm command If you want the arm disarm chirps turned off permanently please refer to the User Selectable Features section of this guide 10 2005 directed electronics all rights reserved remote sensor disable This can be performed anytime the system is armed Follow the proce dure listed below 1 2 Arm the system Using the remote press aa and simultaneously The indicators will flash four times all Warn Away zones of optionally installed sensors are now bypassed zones two and three Using the remote press aa and 3 simultaneously again The lights will flash four more times All optional sensor Warn away and Full trigger zones and the Tilt Sensor are now bypassed The sensor
26. remote is powered by a 12V miniature battery type 27A your warranty It is necessary to retain your sales receipt which reflects that the prod uct was installed by an authorised dealer For full details regarding your warranty coverage please refer to the consumer warranty section of this guide 2005 directed electronics all rights reserved 3 remote configurations The 3000 system has an in key 2 button remote control and a 3 button remote control Two additional Merlin remote controls can be added IN KEY 2 BUTTON REMOTE CONTROL FRONT LED ACCESSORY ARM DISARM PANIC 3 BUTTON REMOTE CONTROL ie LED FrO ___ ACCESSORY ARM DISARM PANIC cy 3 SILENT ARM DISARM id y WMerlin SS J 4 2005 directed electronics all rights reserved remote functions lt 22 This system uses computer based code learning to learn the remote buttons This makes it possible to assign any remote button to any sys tem function The remotes initially come programmed with standard configuration The buttons in all of the instructions in this manual cor respond to a standard configuration remote Standard configuration for in key 2 button remote aA Button The arming disarming and panic functions are controlled by this button 3 Button An optional accessory convenience or expansion function that you have added to your system can be activated by pressing this button d a and 3K
27. remote valet on off This feature allows you to set remote Valet on or off reset to default This feature allows you to restore the programming to factory defaults except for the PIN code and remote controls programmed into the system user selectable features descriptions column three The features in this column pertain to programming individual remote channels in custom configurations Following is an explanation of the features To program specific functions to a different button enter the function you are programming after the chirp confirmation Press the button with which you wish to control that feature the system will chirp to confirm that it has learned the new button arm disarm only e The remote control channel programmed into this feature will arm disarm the system only 2005 directed electronics all rights reserved 27 note When programming a remote control to custom configuration a remote button must first be learned to the arm disarm The rest of the features in this column can then be learned A remote button can only be learned to one designated feature That is if the lock unlock button is programmed for armed disarmed fea ture 1 in column 3 it cannot be programmed for another additional feature listed in column 3 of the User Selectable Features accessory output e The remote channel programmed into this feature will acti vate the accessory output silent mode e The remote cha
28. sed and appear to stop working If five chirps are heard when disarming NPC has been engaged If you wish to clear the NPC memory turn the ignition key on NPC is On Off programmable See your dealer and the Programming section of this guide for more information multiple event total recall This will report the last eight system triggers in reverse chronological order 1 Press and hold _ of the Valet switch 2 While still holding BS arm and disarm the system then release the f button 3 The LED will start to flash to indicate the most recent trigger and proceed down to the eighth trigger For more informa tion please refer to the Table of Zones section of this guide battery back up siren The built in battery back up siren protects the system if a thief discon nects power and or cuts or tampers with the power supply wires while the system is armed If system power is lost the siren will sound for five minutes and then reset 2005 directed electronics all rights reserved 15 diagnostics eee The microprocessor at the heart of your security system is constantly monitoring all of the switches and sensors that are connected to it It detects any faulty switches and sensors and prevents them from dis abling the entire system The microprocessor will also record and report any triggers that occurred during your absence arming diagnostics If the system is armed while an input is active sensor triggering
29. state of the art motorcycle security system It has been designed to provide years of trouble free operation This system must be installed by an authorised dealer Installation of this product by anyone other than an authorised dealer voids the warranty As verification of authorization all authorised deal ers are provided with preprinted dealer certificates In order to maximize the use of this system please review this owner s guide carefully prior to using your system You can print additional or replacement copies of this owner s guide by accessing the Directed website at www directed com note Your system MUST be installed by an Authorised dealer in accor dance with the instructions we supply them The Merlin 3000 system is designed to be installed on any 12 volt negative ground motorcy cle or moped 2 2005 directed electronics all rights reserved note Other than the remote controls this system has no userservice able parts Your authorized dealer can correct any system wiring prob lems and if needed can return any malfunctioning component to Directed Electronics for repair replacement under the terms of the limited Lifetime Warranty printed at the beginning of this guide system maintenance The system requires no specific maintenance The batteries in your remotes will last approximately one year under normal use Your 3 but ton remote is powered by a miniature 3V lithium battery CR2032 Your in key 2 button
30. the most accurate tilt vertical and horizon tal sensing possible f a protected switch is opened the system will immediately trigger the siren and flash the indicator lights The immobiliser prevents the motorcycle s engine from starting 2005 directed electronics all rights reserved 7 disarming To disarm the system press aa You will hear two chirps and the parking lights will flash twice If the siren chirps four times when disarm ing refer to the Diagnostics section of this guide This is called Tamper Alert If the siren is active sounding when the system is disarmed you will hear three chirps but the system is not disarmed Refer to the Remote Siren Silencing section of this guide However if the alarm com pletes the full trigger cycle when disarmed you will hear four chirps disarming without a remote This feature allows you to disarm the system without the remote should it be lost damaged or disabled In order to disarm without a remote you must have the motorcycle s ignition key know where the Valet switch is located and have the PIN code Be sure to check with the installer for the location of the Valet switch Turn the ignition On and then enter the PIN code as given in the fol lowing example to disarm without a remote 1 Find the preset PIN code given in this manual FOR EXAMPLE To disarm first enter a PIN code of 4301 Turn the ignition On Press four times Then once
31. yed back when the alarm is triggered Use the following procedure to set this feature 1 Enter the feature 2 Press the w o button of the remote to begin the playing of siren sounds 3 Siren will generate each sound for 5 seconds There are 6 in total 4 To add the sound press the a button on the Valet switch while that sound is playing 5 To delete the sound press the button on the Valet switch while that sound is playing note After selecting or deleting a sound the siren will immediately play the next sound If no sounds are selected by pressing the B or button the system will remain in its previous setting NPC on off Nuisance Prevention Circuitry NPC stops repeated triggering of the same zone If one zone is triggered three times in one hour that zone is bypassed for one hour starting from the time of the third trigger During that hour if the system detects a trigger on that zone again the 26 2005 directed electronics all rights reserved system resets the one hour timer If one hour passes and the zone has not triggered again the zone is activated and can trigger the system again NPC monitors sensor inputs and the door trigger If NPC is turned off the system will resoond to repeated triggers on the sensor inputs and will do so indefinitely Some states have laws regulating how many times a security system can trigger before it is considered a nui sance and the vehicle is towed away
Download Pdf Manuals
Related Search