Dimplex (SP4) SP420 Indoor Fireplace User Manual
Contents
1. This section provides step by step instructions for selecting a location and preparing the site to install the fireplace into the following Existing Fireplace 1 Make sure that the fire is located on a flat surface 2 Seal all draughts and vents to prevent chimney debris from falling onto the Fireplace Insert Do not install into an existing fireplace that is prone to dampness 3 Remove the fire front panel by following the steps as outlined in Lamp Replacement sections 4 Locate the 4 fixing holes position the fire accordingly and firmly fix the appliance to the wall using the appropriate screws see Fig 5a 5 Replace the front panel New Support Structure Construction When planning where to position your purpose built support structure the following steps must be observed 1 Place the fire in the desired location to see how it will look in the room 2 Mark the desired location for the new support structure in the room and store the fire in a safe dry and dust free location 3 Using timber studs to support the fire devise and construct a suitable means of supporting the product within the wall partition and provide electrical power for the fire to be HARD wired For recommended sizes of height width and depth of opening for recess and hole fixing dimensions for each model see Table 1 and Fig 5a 4 When the structure is complete remove the front panel of the fire by following the steps as outline2. On the SP920 the front panel is held at the bottom by a fixing screw To gain access to lamps please apply the following procedure Remove the fixing screw from the base of the front frame on the SP920 see Fig 12 While holding the front panel by its sides with both hands carefully tilt the bottom of the frame outwards until free and then lift the panel up 1 and then away 2 from the main body see Fig 12 To gain access to the bulbs remove the screws at A to remove the cover bracket X and the screws at B to remove the cover bracket Y see Fig 10a For access to the bottom bulbs carefully slide the flexible rotisserie see a in Fig 11 to one side ensuring that the rubber grommet is not lost see b in Fig 11 Remove the defective lamp by unscrewing it see Fig 11 Replace with a 60W E14 SES Clear Candle bulb rotating it Take care not to over tighten the lamp Steps for reassembling the heater 1 Refit the rotisserie making sure that the rubber grommet is carefully pushed into the slotted hole on the axial bracket 2 Replace the cover brackets X and Y see Fig 10a 3 Replace the front by aligning the slots on the front frame and making sure that it catches fully on the support brackets The magnets on the chassis will hold the front flush to the main body SP520 4 Replace the fixing screw on the base of the front frame SP920 Cleaning WARNING
3. satisfactory service Please retain your receipt as proof of purchase Dimplex UK Limited UK customer help line 8 00am 5 00pm Mon Fri and 8 30am 1 00pm Sat October March Millbrook H ei ae Technical Services Tel 0845 600 5111 Hedge End Fax 01489 773053 Southampton e mail technical services dimplex co uk Hampshire SO30 2DF Republic of Ireland Tel 01 8424833 c Dimplex UK Limited All rights reserved Material contained in this publication may not be reproduced in whole or in part without prior permission in writing of Dimplex UK Limited
4. the bottom holding pins are undone carefully pull forwards at the top until the top pins detach and then lift the front panel up and out see Fig 10 To gain access to the bulbs remove the screws at A to remove the cover bracket X see Fig 10a For access to the bottom bulbs carefully slide the flexible rotisserie see a in Fig 11 to one side ensuring that the rubber grommet is not lost see b in Fig 11 Remove the defective lamp by unscrewing it see Fig 11 Replace with a 60W E14 SES Clear Candle bulb rotating it Take care not to over tighten the lamp Steps for reassembling the heater 1 Refit the rotisserie making sure that the rubber grommet is carefully pushed into the slotted hole on the axial bracket 2 Replace the cover bracket Xx see Fig 10a 3 Replace the front by aligning the slots on the front frame and making sure that it catches fully on the support brackets Lamp Replacement SP520 amp SP920 WARNING ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE REMOVING LAMPS Warning The lamps reach high temperatures during operation For this reason allow the lamps to cool down after switching off the appliance The front panel will need to be removed in order to change lamps see Fig 12 Warning The front panel is heavy and easily damaged The front panel is supported at the top by the chassis and held tight by magnets at the top and bottom on the SP520 model
5. ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER For general cleaning use a soft clean duster never use abrasive cleaners The glass viewing screen should be cleaned carefully with a soft cloth DO NOT use proprietary glass cleaners Recycling For electrical products sold within the European Community At the end of the electrical products useful life it should not be disposed of with household waste Please recycle where facilities exist Check with your Local Authority or retailer for recycling advice in your country After Sales Service Your product is guaranteed for one year from the date of purchase Within this period we undertake to repair or exchange this product free of charge excluding lamps amp subject to availability provided it has been installed and operated in accordance with these instructions Your rights under this guarantee are additional to your statutory rights which in turn are not affected by this guarantee Should you require after sales service you should contact our customer services help desk on 0845 600 5111 It would assist us if you can quote the model number series date of purchase and nature of the fault at the time of your call The customer services help desk will also be able to advise you should you need to purchase any spares Please do not return a faulty product to us in the first instance as this may result in loss or damage and delay in providing you with a
6. E ffect only Flame Effect amp HeatOn The Standby switch must first be turned ON to operate the heater manually or by remote control Note It takes some time for the receiver to respond to the transmitter DO NOT PRESS the buttons more than once within two seconds for correct operation To go to the previous settings press the O button Pressing the O button on the remote turns off the light amp heat settings To resume press the I button until the desired setting is reached see Fig 8 To increase or decrease the brightness of the flames use the dimmer button or the Q button on the Remote Control The heat setting will remain the same To turn off the power the Standby Switch must be turned OFF Lamp Replacement SP420 WARNING ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE REMOVING LAMPS Warning The lamps reach high temperatures during operation For this reason allow the lamps to cool down after switching off the appliance The front panel will need to be removed in order to change lamps see Fig 10 Warning The front panel is heavy and easily damaged The front panel is fixed with 4 spring loaded pins see a in Fig 9 and is supported at the top by the chassis To gain access to lamps please apply the following procedure While holding the front panel by its sides with both hands carefully pull forwards the panel at the bottom until the pins detach from the clips see Fig 9 When
7. XDimplex SP4 SP420 SP5 SP520 SP9 SP920 08 19222 6 UK Issue 6 C Products comply with the European Safety Standard EN 60335 2 30 and the European Standards for Electromagetic Compatibility EMC EN55014 1 A2 2002 and EN55014 2 2003 which cover the essential requirements of EEC directives 73 23 and 89 336 300 min 300 min 300 min 600 recommended 600 recommended 600 recommended MAN AUTO ON OFF apie man ET srozo EE OFF SP520 amp SP920 SP520 amp SP920 Wall Fires Models SP420 SP520 amp SP920 IMPORTANT THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE Important Safety Advice When using electrical appliances basic precautions should be followed to reduce the risk of fire electric shock and injury to persons including the following If the appliance is damaged check immediately with the supplier before installation and operation Do not use this heater in the immediate surroundings of a bath shower or swimming pool Do not use outdoors Do not cover or obstruct the heater in any way Overheating will result if it is accidentally covered In the event of a fault unplug the heater Unplug the heater when not required for long periods The supply cord is recommended to be placed on the right hand side of the heater The hea
8. d in Lamp Replacement sections 5 Locate the 4 fixing holes position the fire accordingly and firmly fix using the appropriate screws 6 Replace the front panel TABLE 1 Models A B X Y Z SP420 871 570 847 646 115 SP520 1160 560 1143 640 146 SP920 914 565 895 676 150 NOTE The appliance should be HARD wired to an electrical power outlet when placed in a recessed installation Please consult a qualified electrician for appropriate wiring requirements Manual Operation SP420 amp SP920 The switches are located at the bottom right side of the heater The Standby Switch Switch S1 must be first turned ON and the AUTO MAN Switch S2 switch set to MANUAL to operate the manual controls see Fig 6 Note When the fire is put in Manual mode the first time the flame effect will come on indicated by the Bottom neon coming on for 3 seconds see Fig 7 Manual Operation SP520 The switches are located at the bottom right side of the heater see Fig 6 Remote Operation The standby switch S1 must first be turned ON and the AUTO MAN Switch turned to AUTO SP420 amp SP920 Note It takes some time for the receiver to respond to the transmitter DO NOT PRESS the buttons more than once within two seconds for correct operation Manual amp Remote Operation Setting Operation Setting Press the 1 button Switch 3 Top Neon Press the I button again Switch 3 Bottom Neon Flame
9. s a 300 watt heat output from the fuel effect and an additional 200 watt output when the heated glass panel is in operation The heater can be used remotely or manually see Operation General features of remote control are Activate Deactivate heated glass panel The illumination of fuel effect can be increased or decreased Please note Used in an environment where background noise is very low it may be possible to hear the motor which operates the flame effect This is normal and should not be a cause for concern Installation Do not connect appliance until properly fixed to the wall and the Instruction leaflet is read fully The minimum distances must be observed For installation of the appliance care must be taken not to damage concealed cables Please be careful while drilling the holes This model is designed to be permanently fixed to a wall at a minimum height of 300mm The wall bracket must be fitted horizontally and the cable routed to the bottom right of the heater as in Fig 1 A height of 600mm from bottom of heater to floor is recommended for optimum viewing of fuel bed see Fig 2 for recommended fixing dimensions For optimum viewing mark the top four screw fixing positions on wall in accordance with the recommended fixing dimensions see Fig 2 Drill holes with a 6mm drill bit Fix the wall bracket using the plugs and screws provided see Fig 3 Carefully lift the heater up ensuring tha
10. t the top rear ledge of heater engages the wall bracket and is sitting centrally positioned see Fig 4 b Rotate the bottom fixing bracket down see Fig 4 c Gently bring the heater level with the wall see Fig 4 d Mark the bottom hole position see Fig 5 remove the heater ensuring that the bottom fixing bracket is rotated up Drill and fit wall plug Refit the heater to the wall fixing bracket i e follow steps as in Fig 4 a b c and d and rotate the bottom fixing bracket down again and use the screw provided to permanently fix the heater in place The heater should not be connected until the instruction leaflet is read fully Recessed Installation Please note that this appliance can also be wall mounted so that it is recessed This can be installed in a large fireplace opening or a purpose built wall See Table 1 for size of recess required and hole fixing dimensions and Fig 5a This fireplace insert does NOT require venting In order to ensure it s future safety in use it is essential that this fire is securely fixed to the wall IT IS IMPORTANT THAT THE FIXING DEVICE CHOSEN IS APPROPRIATE TO THE WALL MATERIAL TO WHICH THE FIRE IS BEING FIXED SOME MODERN INTERNAL BUILDING MATERIALS ARE VERY LOW DENSITY BLOCK AND REQUIRE SPECIALIZED FIXING DEVICES TO PROVIDE A SAFE SECURE INSTALLATION The installation of this fire should be carried out by a competent person If in doubt please consult your local builder
11. ter can also be HARD wired this is recommended if the heater is recessed see Recessed Installation This appliance is not intended for use by children or other persons without assistance or supervision if their physical sensory or mental capabilities prevent them from using it safely Children should be supervised to ensure that they do not play with the appliance If the supply cord is damaged it must be replaced by the manufacturer or service agent or similarly qualified person in order to avoid a hazard Electrical WARNING THIS APPLIANCE MUST BE EARTHED This heater must be used on an AC supply only and the voltage marked on the heater must correspond to the supply voltage Do not switch the appliance on until properly installed Please read all the safety warnings and operating instructions General Unpack the heater carefully and retain the packaging for possible future use in the event of moving or returning the fire to your supplier Contents of Carton Heater Wall fixing bracket Fixing screws and wall plugs Remote control and batteries AAA s type Spare bulb Do not connect the heater to an electricity supply until it is installed on a wall correctly see Installation SP420 amp SP920 When in operation there is a 300 watt heat output from the fuel effect and an additional 120 watt output when the heated glass panel is in operation SP520 When in operation there i
Download Pdf Manuals
Related Search