Home

Cisco Systems 7911G IP Phone User Manual

Contents

1. 1 30 The lap part of the belt should be worn low and snug on the hips just touching the thighs In a crash this applies force to the strong pelvic bones And you d be less likely to slide under the lap belt If you slid under it the belt would apply force at your abdomen This could cause serious or even fatal injuries The shoulder belt should go over the shoulder and across the chest These parts of the body are best able to take belt restraining forces The safety belt locks if there s a sudden stop or a crash or if you pull the belt very quickly out of the retractor You can be seriously hurt if your shoulder belt is too loose In a crash you would move forward too much which could increase injury The shoulder belt should fit against your body To unlatch the belt just push the button on the buckle 1 31 Center Rear Passenger Position Lap Shoulder Belt If your vehicle has a bench seat someone can sit in the center position When you sit in the center seating position you have a lap safety belt which has no retractor You also have a shoulder belt which has a retractor In order to have the protection of the shoulder belt you must i 1 Remove the shoulder belt from its stowage location first connect it to the lap belt in the roof and pull it all the way down to the lap belt 1 32 2 Insert the metal knob on the shoulder belt into the 3 To make the lap belt longer t
2. 5 103 Care of Safety Belts ceeeeeeeeeeeeeeeee es 5 106 Weatherstrips wis ssccsccescrstavenssseexckdonusncatenieense 5 106 Cleaning the Outside of Your Vehicle 5 106 Sheet Metal Damage eeeeeneeeeeeeeeees 5 108 Finish Damage 2icicstitscsacs vest santeee tegen evs 5 109 Underbody Maintenance ceceeeeeee eee 5 109 Chemical Paint Spotting eeeeeeeeeee ees 5 109 Vehicle Care Appearance Materials 5 110 Vehicle Identification eee 5 111 Vehicle Identification Number VIN 5 111 Service Parts Identification Label 5 111 Electrical System ccceeeeeeeeeeeeeeee eee es 5 112 Add On Electrical Equipment 6 eee 5 112 Headlamp Wiring ceeeeeeeeeeeeeeeeeeeeeee eens 5 112 Windshield Wiper Fuses seeeeeeeeeeee ees 5 112 Power Windows and Other Power Options 5 112 Fuses and Circuit Breakers ceeeeeeeee ees 5 113 Capacities and Specifications 5 118 Service Your dealer knows your vehicle best and wants you to be happy with it We hope you will go to your dealer for all your service needs You will get genuine GM parts and GM trained and supported service people We hope you will want to keep your GM vehicle all GM Genuine GM parts have one of these marks ACVelco E parts GM Goodwrench
3. eeeeeeeeees 3 119 Cleaning the Video Screen 0 0eeeeeees 3 119 Integrated Windshield Antenna 5 3 119 XM Satellite Radio Antenna System 48 Contiguous US States 2 3 119 NOTES 3 3 Instrument Panel Overview The main components of the instrument panel are the following A Side Outlets See Outlet Adjustment on page 3 30 B Instrument Panel Cluster See nstrument Pane C D IQmm J K ks M on page 3 32 Hazard Warning Flasher Switch See Hazard Warning Flashers on page 3 6 Head Up Display Switch and Driver Information Center DIC Controls or DIC Controls See Head Up Display HUD on page 3 20 and DIC Controls nd Displays on page 3 55 Center Outlets See Outlet Adjustmenij on page 3 30 Audio System See Audio System s on page 3 64 Side Outlets See Outlet Adjustment on page 3 30 Turn Signal Multitunction Lever See Turn Signal Multifunction Leven on page 3 8 Exterior Interior Lamp Switch See Exterior Lamps Intoror Lamps on page 3 13 and nterior Lamps on page 3 15 Audio Steering Wheel Controls See Audio Steering Wheel Controls eel Controls on page 3 117 Hood Release See on page 5 11 Parking Brake See on page 2 25 Horn See on page 3 7 N O P Q R Console Cooler See Floor Console Fuse Block See Tu V W X Ignitio
4. 0 ccceceeeeeeee eee 3 116 Antenna Integrated Windshield 0 3 119 Understanding Radio Reception 3 118 Antenna XM Satellite Radio Antenna System 3 119 XM Satellite Radio Antenna System 3 119 Anti lock Brake System ABS cccecceeeeeeeees 4 8 Auto Door Lock Unlock ccccceeceeeeeeeeee ees 3 60 Automatic Headlamp System W sssseeererereee 3 15 Automatic Level Control W u ssssseeerererrereee 4 41 Automatic Transaxle PUIG Ea se EA AL E 5 20 eol I reii o Ar EE E SE SSR RE ESSENS 2 22 Backing UD naciisman a 4 47 Battery sovesncctevieti BESS RERS E E E SE 5 41 Battery Replacement X ussssesereeeeerees nerne rnnes 2 6 Battery Run Down Protection i c 3 19 Before Leaving on a Long Trip eee 4 25 Before YOU Drive 34 aurora eniecentinwiye 3 103 Bench Seat Split centeret aeneis 1 6 Brake Low Fluid Warning Message ccecce 3 50 Parking srei nonao oneee a E N E A 2 25 System Warning Light u u ssseseeeeeererererer 3 36 Brake Fluid arsen here erensia 5 38 Brake Wear isis iieis naroa uaea ii 5 40 Brako Sipser on a Oa 5 38 Braking seeren orroe lat Sees AE ELET 4 7 Braking in Emergencies G ssseseeeeeese ren knner 4 10 Break In New Vehicle ccccececeeeeeeeeaeeeeeees 2 18 Bulb Replacement 222222 dn srt busser Uke nn 5 50 Front Turn Signal Sidemarker and Parking AMPS aesan E ineci
5. c ceeeeeeeeeeeeeeeeeeeeeeaes 1 6 Rear Seat Outside Passenger Positions 1 28 Rear Seat Passengers Safety Belts 1 28 Rear Storage Area cceceeeeeeeeeeeeeeeeeeeeeeeeen ees 2 37 Rear Window Defogger seeeeeeeee es 3 26 3 29 Rearview Mirrors Ea oss nanen are 2 31 Reclining Seatbacks ccceeeeeeeeeeeeeeee asien 1 4 Recommended Fluids and Lubricants 6 12 Recreational Vehicle Towing ccecce 4 34 Remote Alari auiensicakincegttaheaneseeddhes e eeina 2 5 Remote Control cccceeeeeeeeeeeeeeeneeeeeneeeeenes 3 109 Remote Door Unlock ccecceceeceeeeeeeeeeees Remote Keyless Entry System 0 eeeeeeeeee ee Remote Keyless Entry System Operation Remote Keyless Entry Transmitter Battery Low Warning Message eeeseeeneeeeeeeeee teeta tees Removing the Flat Tire and Installing the Spare Tire ccecceeeeeeeeee eee eee eee eea tenes Removing the Floor Track Assembly Removing the Sliding Rear Convenience Tray Removing the Spare Tire and Tools 5 Removing the Split Bench Seat 2 Replacement Bulbs Replacing Brake System Parts se Replacing Restraint System Parts After a Crash Replacing the Floor Track Assembly Replacing the Sliding Rear Convenience Tray Replacing the Split Bench Seats 2055 Reporting Safety Defects Canadia
6. 2 Use the tool to remove the screw located in the side rail assembly in front of the front crossrail 3 Repeat for the other side 4 Put the tool and the screws back in the plastic bag in the glove box 2 40 To adjust the crossrails lift the release levers on each side to unlock them Slide the crossrails forward or backward as needed to accommodate loads of various sizes After repositioning the crossrails engage the release lever This will lock the crossrails in place Notice Opening the sunroof when the luggage rack crossrails are not in the full rear position could cause damage to the sunroof or luggage rack Verify the luggage rack crossrails are in the full rear position before opening the sunroof Use the four tie down loops in each of the side rails to help secure large loads When you are done using the crossrails you must replace the sunroof stop To replace the sunroof stop do the following 1 Put the crossrails in the full rear position 2 Using the tool put the screws back into each side rail assembly Make sure the screws are in the first hole in front of the crossrail Convenience Net Your vehicle may have a convenience net The convenience net is designed to help keep small loads like grocery bags from falling over Install the convenience net at the rear of your vehicle just inside the liftgate tailgate opening Attach both the upper and lower hooks to the loops on either sid
7. Here are some tips on night driving Drive defensively Do not drink and drive Adjust your inside rearview mirror to reduce the glare from headlamps behind you Since you can not see as well you may need to slow down and keep more space between you and other vehicles Slow down especially on higher speed roads Your headlamps can light up only so much road ahead In remote areas watch for animals If you are tired pull off the road in a safe place and rest No one can see as well at night as in the daytime But as we get older these differences increase A 50 year old driver may require at least twice as much light to see the same thing at night as a 20 year old What you do in the daytime can also affect your night vision For example if you spend the day in bright sunshine you are wise to wear sunglasses Your eyes will have less trouble adjusting to night But if you are driving do not wear sunglasses at night They may cut down on glare from headlamps but they also make a lot of things invisible You can be temporarily blinded by approaching headlamps It can take a second or two or even several seconds for your eyes to re adjust to the dark When you are faced with severe glare as from a driver who does not lower the high beams or a vehicle with misaimed headlamps slow down a little Avoid staring directly into the approaching headlamps Keep your windshield and all the glass on your vehicle clea
8. It is important to have the correct hitch equipment Crosswinds large trucks going by and rough roads are a few reasons why you will need the right hitch Here are some rules to follow e If you will be pulling a trailer that when loaded will weigh more than 2 000 Ibs 900 kg be sure to use a properly mounted weight carrying hitch and sway control of the proper size This equipment is very important for proper vehicle loading and good handling when you re driving Will you have to make any holes in the body of your vehicle when you install a trailer hitch If you do remember to seal the holes when you remove the hitch If you do not seal them deadly carbon monoxide CO from your exhaust can get into your vehicle See Engine Exhaust on page 2 29 Dirt and water can too Safety Chains You should always attach chains between your vehicle and your trailer Cross the safety chains under the tongue of the trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch Instructions about safety chains may be provided by the hitch manufacturer or by the trailer manufacturer Follow the manufacturer s recommendation for attaching safety chains and do not attach them to the bumper Always leave just enough slack so you can turn with your rig Never allow safety chains to drag on the ground Trailer Brakes If your trailer weighs more than 1 000 Ibs 450 kg loaded then it needs its
9. a be required See Recommended Fluids and mer on page 6 12 5 106 Cleaning the Outside of Your Vehicle The paint finish on your vehicle provides beauty depth of color gloss retention and durability Washing Your Vehicle The best way to preserve your vehicle s finish is to keep it clean by washing it often with lukewarm or cold water Do not wash your vehicle in the direct rays of the sun Use a car washing soap Do not use strong soaps or chemical detergents Be sure to rinse the vehicle well removing all soap residue completely You can get GM approved cleaning products from your dealer See Vehicle Care Appearance Materials on page 5 110 Do not use cleaning agents that are petroleum based or that contain acid or abrasives All cleaning agents should be flushed promptly and not allowed to dry on the surface or they could stain Dry the finish with a soft clean chamois or an all cotton towel to avoid surface scratches and water spotting High pressure car washes may cause water to enter your vehicle Cleaning Exterior Lamps Lenses Use only lukewarm or cold water a soft cloth and a car washing soap to clean exterior lamps and lenses Follow instructions under Washing Your Vehicle Finish Care Occasional waxing or mild polishing of your vehicle by hand may be necessary to remove residue from the paint finish You can get GM approved cleaning products from your dealer See Vehicle Care Appearance
10. cceeeeeeneeeeeeeeeeeeeeees 3 22 Door LOCKS arier nere adeetiwcdd eis ea 2 8 Electrical System sisrsins oosa niiier misiis 5 112 SIX Way Seals cienie aanere aaa nai 1 2 Steering Fluid 2345 soens jader 5 35 WINGOWS sneer aen 2 13 Power Steering seceririsnneteiiiari ninais 4 12 Program Mode Message ecseeeeeeeeeeeeeees 3 51 Programmable Automatic Door Locks 2 9 Questions and Answers About Safety Belts 1 17 Radiator Pressure Cap U W ssssseeeeeereree renere enne 5 25 Radio Data System RDS 3 65 3 75 3 89 Radio Messages eeeeeeeeeeeee ees 3 71 3 80 3 95 Radios 22 vie ce a5 taheusicas Me E E 3 64 Care of Your CD and DVD Player 3 118 Care of Your CDs and DVDs 06 3 118 Radio with CD ceeeeeeeeeeeeeeeeeeeeneees 3 65 3 75 Radio with Six Disc CD 0 00 0 cceeeeeeeeeee eee ees 3 89 Rear Audio Controller RAC eeee 3 116 Setting the Time cceeeeeseeeeeeeeeeeeeeee eens 3 64 Theft Deterrent ceeeeeeeeeeeeeeeeeeeeeeees 3 116 Understanding Reception W W ssseeeeeerereee 3 118 RDS Messages eeeeeeeeeneeeeeeeees 3 70 3 79 3 94 Rear Audio Controller RAC n se 3 116 Rear Hatch Ajar Warning Message 655 3 48 Rear Safety Belt Comfort Guides 0005 1 34 Rear Seat Entertainment System 0 3 103 Rear Seat Operation
11. if so is it all the way in If it is then turn the steering wheel left and right while you turn the key hard Turn the key only with your hand Using a tool to force it could break the key or the ignition switch If none of these works then your vehicle needs service B ACCESSORY This position allows you to use things like the radio and the windshield wipers while the engine is off This position will allow you to turn off the engine but still turn the steering wheel Use ACCESSORY if you must have your vehicle in motion while the engine is off for example if your vehicle is being pushed or towed C ON This is the position that the switch returns to after you start your engine and release the key The switch stays in ON when the engine is running But even when the engine is not running you can use ON to operate your electrical power accessories and to display some instrument panel warning lights D START This position starts the engine When the engine starts release the key The ignition switch will return to ON for normal driving If the engine is not running ACCESSORY and ON are positions that allow you to operate your electrical accessories such as the radio Retained Accessory Power RAP With RAP the power windows the audio system the sunroof and the Automatic Level Control will continue to work up to 10 minutes after the ignition key is turned to OFF and none of the doors are opened Starting Y
12. on page 2 28 in this section for more information It is dangerous to get out of your vehicle if the shift lever is not fully in PARK P with the parking brake firmly set Your vehicle can roll Do not leave your vehicle when the engine is running unless you have to If you have left the engine running the vehicle can move suddenly You or others could be injured To be sure your vehicle will not move even when you are on fairly level ground always set your parking brake and move the shift lever to PARK P See Shifting Into Park P on page 2 26 If you are pulling a trailer see Towing a Trailen on page 4 42 REVERSE R Use this gear to back up Notice Shifting to REVERSE R while your vehicle is moving forward could damage the transaxle The repairs would not be covered by your warranty Shift to REVERSE R only after your vehicle is stopped To rock your vehicle back and forth to get out of snow ice or sand without damaging your transaxle see it You Are Stuck In Sand Mud Ice or Snow on page 4 33 NEUTRAL N In this position your engine does not connect with the wheels To restart when you are already moving use NEUTRAL N only Also use NEUTRAL N when your vehicle is being towed Shifting into a drive gear while your engine is running at high speed is dangerous Unless your foot is firmly on the brake pedal your vehicle could move very rapidly You could lose control and hit people or ob
13. t designed to inflate at all in rollover rear or low speed frontal crashes or in many side crashes And for some unrestrained occupants frontal air bags may provide less protection in frontal crashes than more forceful air bags have provided in the past The side impact air bags for the driver and right front passenger are designed to inflate only in moderate to severe crashes where something hits the side of your vehicle They aren t designed to inflate in frontal in rollover or in rear crashes Everyone in your vehicle should wear a safety belt properly whether or not there s an air bag for that person Both frontal and side impact air bags inflate with great force faster than the blink of an eye If you re too close to an inflating air bag as you would be if you were leaning forward it could seriously injure you Safety belts help keep you in position for air bag inflation before and during a crash Always wear your safety belt even with frontal air bags The driver should sit as far back as possible while still maintaining control of the vehicle Front occupants should not lean on or sleep against the door Anyone who is up against or very close to any air bag when it inflates can be seriously injured or killed Air bags plus lap shoulderbelts offer the best protection for adults butnot for young children and infants Neither the vehicle s safety belt system nor its air bag system is designed for them
14. until the windshield is warmed Otherwise the washer fluid can form ice on the windshield blocking your vision Cruise Control With cruise control you can maintain a speed of about 25 mph 40 km h or more without keeping your foot on the accelerator This can really help on long trips Cruise control does not work at speeds below about 25 mph 40 km h When you apply your brakes the cruise control disengages e Cruise control can be dangerous where you can not drive safely at a steady speed So do not use your cruise control on winding roads or in heavy traffic Cruise control can be dangerous on slippery roads On such roads fast changes in tire traction can cause needless wheel spinning and you could lose control Do not use cruise control on slippery roads If your vehicle is in cruise control when the traction control system begins to limit wheel spin the cruise ontrol will automatically disengage See Control System TCS on page 4 10 When road conditions allow you to safely use it again you may turn the cruise control back on Setting Cruise Control If you leave your cruise control on when you are not using cruise you might hit a button and go into cruise when you do not want to You could be startled and even lose control Keep the cruise control switch off until you want to use cruise control 1 Move the cruise control switch to ON 2 Get up to the speed you want 3 Press th
15. EYES BY SHIELDING CAUSTIC BATTERY ACID COULD CAUSE BURNS AVOID SPARKS OR FLAMES SPARK OR FLAME COULD EXPLODE BATTERY LATCH BOTH LAP AND SHOULDER BELTS TO PROTECT OCCUPANT DO NOT TWIST SAFETY BELT WHEN ATTACHING FASTEN SEAT BELTS MOVE SEAT FULLY REARWARD cnet CHILD SEAT ve PULL BELT OUT COMPLETELY THEN SECURE Van CHILD SEAT POWER t WINDOW B AIR BAG X DO NOT INSTALL A REAR FACING CHILD RESTRAINT IN THIS SEATING POSITION e DO NOT INSTALL A FORWARD FACING CHILD RESTRAINT IN THIS SEATING POSITION DOOR LOCK UNLOCK MASTER LIGHTING SWITCH TURN SIGNALS PARKING LAMPS HAZARD WARNING FLASHER DAYTIME RUNNING LAMPS s 1 1 og ENGINE COOLANT TEMP ENGINE COOLANT BATTERY CHARGING SYSTEM OWNER S MANUAL ENGINE OIL PRESSURE Fo ANTI LOCK 3 BRAKES SERVICE pume SERVICE gt MANUAL Eem 4 NOTES vi Section 1 Seats and Restraint Systems Front Seats sssssseeeerererenee renerne renerne 1 2 Manual Passenger Seat W W W sseeeeeeeeerereerrree 1 2 Six Way Power Seats c ccseeeeeeeeeeneeeeeneees 1 2 Manual Lumbar dosein 1 3 Heated Seats onairea enea 1 3 Reclining Seatbacks W Wu u u dsseeeereeeererer renerne 1 4 Head Restraints 352255 re re eea E 1 5 Rear Seats oane EA 1 6 Rear Seat Operation W ssssseeeerereeerere rener 1 6 Split Bench Seat
16. Enty LIQHUNG seatecetsiueeses traded kleine T ies 3 17 Event Data Records EDR eeeeeeeeeee eee 7 10 Ext Lighting siera anken nende ps vated 3 18 Exiting Programming Mode seee 3 63 Express Down Window aser parkens 2 13 Extender Safety Belt 0 cceceeeeeeeeeeeeeeees 1 38 Exterior Lamps opinisonda 3 13 Filter Engine Air Cleaner W u ssseeeeeeerrerererrnnenee 5 18 Finding a Program Type PTY Station RDS and XM reden 3 68 3 78 3 92 Finding a Station said sed 3 66 3 76 3 91 FINISH Care isischlivcancsneaacndeadeecsanntreascacchntecces 5 107 Finish Damage cisssesccciieeanariaceiae skeder DE 5 109 FlaSh tO PaSS aan dead aeaee 3 9 Flat TGs camere aaan SE SEER ERE RE ES AS 5 77 Flat Tire Changing sssseeeeeeeeee renerne renerne 5 78 Floor Console Fuse Block o on 5 113 Fluid Automatic Transaxle ccceeeeeeeeeeeeeeeeee ees 5 20 Power Steering cciveseccets ect ediedetietaladieestls 5 35 Windshield Washer eeeeeeeeeeee renee eens 5 36 FIM Stereo an aeaaee ia ieai 3 118 FOG kampstil oner E G 3 15 Folding or Reclining the Seatbacks 2 1 6 Following Distance c cceeeeeeeneeeeeeeeeeeeeees 4 47 Front Door Utility Packs 2 0 0 eee eee eee beer 2 36 Front Reading Lamps c eeeeeeeeeeeeeeeeee eens 3 19 UCI 25 ot satanahsrantewnag a s a a Ea 5 4 ROOIINGS seirene aE E 5 6 California Fuel 22 ar era canini ennei 5 5 Filling a Portable Fuel Conta
17. Failure to use the proper fluid can cause leaks and damage hoses and seals Windshield Washer Fluid What Washer Fluid to Use When you need windshield washer fluid be sure to read the manufacturer s instructions before use If you will be operating your vehicle in an area where the temperature may fall below freezing use a fluid that has ffi n against freezing See Engind icien i Compartment Overview on page 5 12 for reservoir location Adding Washer Fluid Fill your washer fluid tank only three quarters full when it s very cold This allows for Open the cap with the expansion if freezing occurs which could washer symbol on it Add damage the tank if it is completely full washer fluid until the Don t use engine coolant antifreeze in your tank is full windshield washer It can damage your washer system and paint Notice When using concentrated washer fluid follow the manufacturer s instructions for adding water Don t mix water with ready to use washer fluid Water can cause the solution to freeze and damage your washer fluid tank and other parts of the washer system Also water doesn t clean as well as washer fluid 5 37 Brakes Brake Fluid Your brake master cylinder reservoir is filled with DOT 3 brake fluid See Engine Compartment Overview on page 5 12 for the location of the reservoir There are only two reasons why the brake fluid level in the reservoir might go down T
18. III Operation Your vehicle is equipped with the PASS Key III Personalized Automotive Security System theft deterrent system PASS Key III is a passive theft deterrent system This means you don t have to do anything different to arm or disarm the system It works when you insert or remove the key from the ignition When the PASS Key III system senses that someone is using the wrong key it shuts down the vehicle s starter and fuel systems The starter will not work and fuel will stop being delivered to the engine Anyone using a trial and error method to start the vehicle will be discouraged because of the high number of electrical key codes When trying to start the vehicle if the engine does not start and the SECURITY message comes on the key may have a damaged transponder Turn the ignition off and try again lf the engine still does not start and the key appears to be undamaged try another ignition key At this time ou may also want to check the fuse See Fuses and Circuit Breakers on page 5 113 it the engine sti does not start with the other key your vehicle needs service If your vehicle does start the first key may be faulty See your dealer who can service the PASS Key III to have a new key made It is possible for the PASS Key III decoder to learn the transponder value of a new or replacement key Up to 10 total keys may be programmed for the vehicle This procedure is for learning addit
19. The Head Up Display also displays a CHECK GAGES icon When you see this icon the following messages could appear on the instrument panel cluster e Engine Coolant Temperature Warning Message See Engine Coolant Temperature Warning Te FE Message on page 37 IE Ne MED made IS too blight of 100 Ngn Low Oil Pressure Message See Low Oil Pressure on page 3 45 your field of view it may take you more time to see things you need to see when it is dark outside Be sure to keep the HUD image dim Charging S ystem Indicator Message See Charging and placed low in your field of view System Indicator Message on page 3 45 Low Brake Fluid Warning Message See Low Brake If your vehicle has the HUD it can display the Fluid Warning Messagejon page 3 50 speedometer reading in English or metric The current audio system information may also be displayed and will appear as an image focused out toward the front of your vehicle The Head Up Display also displays the following messages when they appear on the instrument panel cluster Turn Signal Indicators See Signal Multifunction Leven on page 3 8 e High Beam Indicator See Turn Signal Multifunctio level ver on page 3 8 e Low Fuel Warning Message See Low Fuel Warning on page 3 50 3 20 Under warning conditions the CHECK GAGES icon will illuminate in the HUD look at the instrument panel cluster for more information Notice If you try to use the HUD
20. You can sound the horn by pressing the horn symbols on your steering wheel Tilt Wheel A tilt wheel allows you to adjust the steering wheel before you drive You can raise it to the highest level to give your legs more room when you exit and enter the vehicle The lever that allows you to tilt the steering wheel is located on the left side of the steering column To tilt the wheel hold the wheel and pull the lever Then move the wheel to a comfortable position and release the lever to lock the wheel in place Turn Signal Multifunction Lever CRUISE OTRA WIPER The lever on the left side of the steering column includes the following Turn and Lane Change Signals 2D Headlamp High Low Beam Changer Flash to Pass SZ Windshield Wipers 7 Windshield Washer Cruise Control Turn and Lane Change Signals The turn signal has two upward for right and two downward for left positions These positions allow you to signal a turn or a lane change To signal a turn move the lever all the way up or down When the turn is finished the lever will return automatically An arrow on the instrument panel cluster and the HUD display will flash in the direction of the turn or lane change To signal a lane change just raise or lower the lever until the arrow starts to flash Hold it there until you complete your lane change The lever will return by itself when you release it As you signal a turn or a la
21. You could crash Always have your engine running and your vehicle in gear when you go downhill Know how to go uphill You may want to shift down to a lower gear The lower gears help cool your engine and transaxle and you can climb the hill better Stay in your own lane when driving on two lane roads in hills or mountains Do not swing wide or cut across the center of the road Drive at speeds that let you stay in your own lane As you go over the top of a hill be alert There could be something in your lane like a stalled car or an accident You may see highway signs on mountains that warn of special problems Examples are long grades passing or no passing zones a falling rocks area or winding roads Be alert to these and take appropriate action 4 27 Winter Driving Here are some tips for winter driving Have your vehicle in good shape for winter You may want to put winter emergency supplies in your vehicle 4 28 Include an ice scraper a small brush or broom a supply of windshield washer fluid a rag some winter outer clothing a small shovel a flashlight a red cloth and a couple of reflective warning triangles And if you will be driving under severe conditions include a small bag of sand a piece of old carpet or a couple of burlap bags to help provide traction Be sure you properly secure these items in your vehicle Driving on Snow or Ice Most of the time those places where your tires meet
22. Young children and infants need the protection that a child restraint system can provide Always secure children properly in your vehicle To read how see the part of this manual called Older Children or Infants and Young Children 1 63 There is an air bag Where Are the Air Bags readiness light on the e instrument panel cluster r which shows the air bag symbol The system checks the air bag electrical system for malfunctions The light tells you if there is an electrical problem See Air Bag Readiness Lightton page 3 35 for more information The driver s frontal air bag is in the middle of the steering wheel 1 64 The right front passenger s frontal air bag is in the If your vehicle has one the driver s side impact instrument panel on the passenger s side air bag is in the side of the driver s seatback closest to the door If your vehicle has one the right front passenger s side impact air bag is in the side of the passenger s seatback closest to the door 1 66 If something is between an occupant and an air bag the bag might not inflate properly or it might force the object into that person causing severe injury or even death The path of an inflating air bag must be kept clear Don t put anything between an occupant and an air bag and don t attach or put anything on the steering wheel hub or on or near any other air bag covering Don t let seat covers block the inflation path o
23. Your vehicle may have a trailer wiring harness located at the rear of your vehicle To use the trailer wiring harness you need a converter kit Contact your dealer for more information 4 49 4 NOTES 4 50 Section 5 Service and Appearance Care SEVICE osc case tense iea aaa EE E iiA 5 3 Windshield Washer Fluid eeeeeeeeee eee es 5 36 Doing Your Own Service Work 0 28 5 3 Braks aosipun mani R aRar 5 38 Adding Equipment to the Outside Battery es andele keller aa Rn EE GREE Ss 5 41 Of Your Vehicle ssrsiirerisirnaonnaneia 5 4 UM PSA i setrenssedtcRecaeadteenttanreretantanciense 5 42 UGS RS EET IEEE stents E A ete eeetaseaned 5 4 All Wheel Drive ccccceeeeeeeeeneeeeeeeeee es 5 48 Gasoline Octane cece eee tt tet eteeees 5 4 Bulb Replacement cc 5 50 Gasoline Specifications seerne 5 5 Halogen BUIDS sansatiseesivereainssianeatnsenaseoees 5 50 California Fuel 22 0rcecan aceacesadankenancdinaebagataniceand 5 5 Headlamps cccccecsesceseeseeseeseeseeseeseeseesserees 5 51 Additives Sale preneren ELL EEE LEE ELF EL EE REEL ERE FE EEREEEEE 5 6 Front Turn Signal Sidemarker and Fuels in Foreign Countries sene 5 6 Parkingi LAMPS isere iiemet ei 5 53 Filling Your Tank FEEL KEEL EEK LE EEKE ERE EEEREEEE 5 7 Taillamps Stoplamps and Back up Lamps 5 54 Filling a Portable Fuel Container 00 5 9 Replacement Bulbs c ccececeeeseeeeeeeeee ees 5
24. available Tune to another station If this station was one of your presets you may need to choose another station for that preset button No Info Artist Name Feature not No artist information is available at this time on this available channel Your system is working properly No Info Song Program Title not No song title information is available at this time on this available channel Your system is working properly 3 81 XM Radio Messages cont d Radio Display No Info Category Name not No category information is available at this time on this available channel Your system is working properly No Info No Text Informational No text or informational messages are available at this message available time on this channel Your system is working properly Not Found No channel available for There are no channels available for the category you the chosen category selected Your system is working properly XM Locked Theft lock active The XM receiver in your vehicle may have previously been in another vehicle For security purposes XM receivers cannot be swapped between vehicles If you receive this message after having your vehicle serviced check with the servicing facility Radio ID Radio ID label If you tune to channel 0 you will see this message channel 0 alternating with your XM Radio 8 digit radio ID label This label is needed to activate your service Unknown Radio ID not known If you receive this message when you tune
25. bag inflation doesn t prevent the driver from seeing or being able to steer the vehicle nor does it stop people from leaving the vehicle When an air bag inflates there is dust in the air This dust could cause breathing problems for people with a history of asthma or other breathing trouble To avoid this everyone in the vehicle should get out as soon as it is safe to do so If you have breathing problems but can t get out of the vehicle after an air bag inflates then get fresh air by opening a window or a door If you experience breathing problems following an air bag deployment you should seek medical attention 1 69 In many crashes severe enough to inflate an air bag windshields are broken by vehicle deformation Additional windshield breakage may also occur from the right front passenger air bag Air bags are designed to inflate only once After an air bag inflates you ll need some new parts for your air bag system If you don t get them the air bag system won t be there to help protect you in another crash A new system will include air bag modules and possibly other parts The service manual for your vehicle covers the need to replace other parts Your vehicle is equipped with a crash sensing and diagnostic module which records information about the frontal air bag system The module records information about the readiness of the system when the system commands air bag inflation and driver s safety b
26. between the plies and the tread Cords may be made from steel or other reinforcing materials Bead The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim Bias Ply Tire A pneumatic tire in which the plies are laid at alternate angles substantially less than 90 degrees to the centerline of the tread Cold Inflation Pressure The amount of air pressure in a tire measured in pounds per square inch psi before a tire has built up heat from driving See Inflation Tire Pressure on page 5 66 Curb Weight This means the weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel oil and coolant but without passengers and cargo DOT Markings A code molded into the sidewall of a tire signifying that the tire is in compliance with the U S Department of Transportation motor vehicle safety standards The DOT code includes the Tire Identification Number TIN an alphanumeric designator which can also identify the tire manufacturer production plant brand and date of production iVWR Gross Vehicle Weight Rating see Loading Your Vehicle on page 4 36 GAWR FRT Gross Axle Weight Rating for the front axle see Loading Your Vehicle on page 4 36 5 63 GAWR RR Gross Axle Weight Rating for the rear axle see Loading Your Vehicle on page 4 36 Intended Outboard Sidewall The side of an asymmetrical tire that must always face outward when mounted on a
27. driving is now a good deal longer and not nearly as responsive as your vehicle is by itself Before you start check all trailer hitch parts and attachments safety chains electrical connector lamps tires and mirror adjustment If the trailer has electric brakes start your vehicle and trailer moving and then apply the trailer brake controller by hand to be sure the brakes are working This lets you check your electrical connection at the same time During your trip check occasionally to be sure that the load is secure and that the lamps and any trailer brakes are still working Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving your vehicle without a trailer This can help you avoid situations that require heavy braking and sudden turns Passing You will need more passing distance up ahead when you are towing a trailer And because you are a good deal longer you will need to go much farther beyond the passed vehicle before you can return to your lane Backing Up Hold the bottom of the steering wheel with one hand Then to move the trailer to the left just move that hand to the left To move the trailer to the right move your hand to the right Always back up slowly and if possible have someone guide you Making Turns Notice Making very sharp turns while trailering could cause the trailer to come in contact with the vehicle Your vehicle could be damaged Avoid m
28. frontal air bags would not help you in many types 1 68 of collisions including rollovers rear impacts and many side impacts primarily because an occupant s motion is not toward the air bag Side impact air bags would not help you in many types of collisions including frontal or near frontal collisions rollovers and rear impacts primarily because an occupant s motion is not toward those air bags Air bags should never be regarded as anything more than a supplement to safety belts and then only in moderate to severe frontal or near frontal collisions for the driver s and right front passenger s frontal air bags and only in moderate to severe side collisions for vehicles with a driver s and right front passenger s side impact air bag What Will You See After an Air Bag Inflates After the air bag inflates it quickly deflates so quickly that some people may not even realize the air bag inflated Some components of the air bag module will be hot for a short time These components include the steering wheel hub for the driver s frontal air bag and the instrument panel for the right front passenger s frontal air bag For vehicles with side impact air bags the side of the seatback closest to the driver s and or right front passenger s door will be hot The parts of the bag that come into contact with you may be warm but not too hot to touch There will be some smoke and dust coming from the vents in the deflated air bags Air
29. numbered pushbutton the station you set will return and the equalization that you selected will be automatically stored for that pushbutton 6 Repeat the steps for each pushbutton Setting the Tone Bass Treble TONE Press and release this button until BASS MID or TREB appears on the display The SELECT LED indicator will light to show that the tone control can be adjusted Turn the SELECT knob to increase or to decrease If a station is weak or noisy you may want to decrease the treble Pressing and holding the TONE button until FLAT appears on the display will return all of the tone controls to the middle position EQ Equalizer Press this button to select customized bass midrange and treble equalization settings You can set up to six customized equalization settings by performing the following steps 1 Turn the radio on 2 Use the TONE button and the SELECT knob to create the desired equalization 3 Press and hold the EQ button for two seconds SELECT EQ will appear on the display and the EQ symbol will flash 4 Press EQ or turn the SELECT knob to select the desired EQ number 3 67 5 Press and hold the EQ button or push the SELECT knob to store the equalization setting and the number You will hear a beep and EQ SAVED will appear on the display 6 Repeat the steps for the other EQ settings and numbers EQ 5 has been programmed at the factory for use with talk radio but it can be set to a diff
30. speedometer or odometer calibration headlamp aim bumper height vehicle ground clearance and tire or tire chain clearance to the body and chassis See Changing a Flat Tire on page 5 78 for more information Used Replacement Wheels Putting a used wheel on your vehicle is dangerous You can t know how it s been used or how far it s been driven It could fail suddenly and cause a crash If you have to replace a wheel use a new GM original equipment wheel Tire Chains Don t use tire chains There s not enough clearance Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes suspension or other vehicle parts The area damaged by the tire chains could cause you to lose control of your vehicle and you or others may be injured in a crash Use another type of traction device only if its manufacturer recommends it for use on your vehicle and tire size combination and road conditions Follow that manufacturer s instructions To help avoid damage to your vehicle drive slowly readjust or remove the device if it s contacting your vehicle and don t spin your wheels If you do find traction devices that will fit install them on the front tires for front wheel drive vehicles If your vehicle has all wheel drive install traction devices on either the front tires or all four tires but never on the rear tires only 5 75 Accessory Inflator Your vehicle may have an accessory inf
31. the road probably have good traction However if there is snow or ice between your tires and the road you can have a very slippery situation You will have a lot less traction or grip and will need to very careful What is the worst time for this Wet ice Very cold snow or ice can be slick and hard to drive on But wet ice can be even more trouble because it may offer the least traction of all You can get wet ice when it is about freezing 32 F 0 C and freezing rain begins to fall Try to avoid driving on wet ice until salt and sand crews can get there Whatever the condition smooth ice packed blowing or loose snow drive with caution If you have traction control keep the system on It will improve your ability to accelerate when driving on a slippery road But you can turn the traction system off if your vehicle ever gets stuck in sand mud ice or on page 4 ven thoug your ve icle as a traction system you will want to slow down a ad nike o the road conditions Seal Traction Control on page 4 10 If you do not have a traction system accelerate gently Try not to break the fragile traction If you accelerate too fast the drive wheels will spin and polish the surface under the tires even more 4 29 Unless you have the anti lock braking system you will want to brake very gently too If you do have anti lock see on page 4 7 This system improves your vehicle s stability when you ma
32. 55 Checking Things Under the Hood 5 10 Windshield Wiper Blade Replacement 5 56 FOO Releases enana nan 5 11 Ti 5 58 Engine Compartment Overview n 5 12 ires SE SEE SETE ED ES NS ea z Inflation Tire Pressure W u sssssssseveverernree 5 66 Engine Qil ssegar miana eea iA 5 13 Check Tire P S 5 67 Engine Air Cleaner Filter 0cccccceeeeeeeeeeees 5 18 Ti ie ve R YSE essens eniai ait 5 68 Automatic Transaxle Fluid 1 5 20 ire MSPS ANG I tet GM nasi ronga aisis i Endi When It Is Time for New Tires ccce 5 70 GING COOLANT 5223 lasere ean sncencanindectnetnaceenes 5 22 Buvina New Ti 5 71 Radiator Pressure Cap cceceeeeeeeereeeeeeerees 5 25 ee NES ea Tia cee aaa ae f Endi Uniform Tire Quality Grading sseseeeeree 5 72 gine Overheating 22222 orneer dd snedker dene 5 25 A 2 z Wheel Alignment and Tire Balance 5 73 Cooling SYSTEM ssim eee t nekin eeni 5 28 Wheel Reol 5 74 Power Steering Fluid ccccccccccssceeeeneees 5 35 eel HepIACEMENE soda sensuel eks i 5 1 Section 5 Service and Appearance Care Tite CHAINS rannen aes 5 75 Accessory Inflator 0 cceeeeeeeeeeeeeeeeereeees 5 76 If a Tire Goes Flat ccc ceeeeeeeeeeeeeeeeeee een ees 5 77 Changing a Flat Tire cceeeeeeeeeee teeter eee 5 78 Compact Spare Tire us bara lave 5 102 Appearance Care l a 5 103 Cleaning the Inside of Your Vehicle
33. A First Edition Canadian Owners You can obtain a French copy of this manual from your dealer or from Helm Incorporated P O Box 07130 Detroit MI 48207 About Driving Your Vehicle As with other vehicles of this type failure to operate this vehicle correctly may result in loss of control or an accident See Your Driving the Road and Your Vehicle on page 4 2 copyright General Motors Corporation 05 30 03 All Rights Reserved How to Use This Manual Many people read their owner s manual from beginning to end when they first receive their new vehicle If you do this it will help you learn about the features and controls for your vehicle In this manual you will find that pictures and words work together to explain things Index A good place to look for what you need is the Index in back of the manual It is an alphabetical list of what is in the manual and the page number where you will find it Safety Warnings and Symbols You will find a number of safety cautions in this book We use a box and the word CAUTION to tell you about things that could hurt you if you were to ignore the warning These mean there is something that could hurt you or other people In the caution area we tell you what the hazard is Then we tell you what to do to help avoid or reduce the hazard Please read these cautions If you don t you or others could be hurt You will also find a circle with a slash through it in
34. CD it will be activated each time you play a CD The CD will begin to play automatically As each new track starts to play the track number will appear on the display To insert multiple CDs do the following 1 Turn the ignition on 2 Press and hold the LOAD side of the LOAD CD button for two seconds You will hear a beep and the light located to the right of the slot will begin to flash 3 98 3 Once the light stops flashing and turns green load a CD Insert the CD partway into the slot label side up The player will pull the CD in 4 Once the CD is loaded the light will begin flashing again Press the LOAD side of the LOAD CD button again Once the light turns green load the next CD Repeat this procedure for each CD The CD player takes up to six CDs Do not try to load more than six To load more than one CD but less than six complete Steps 1 through 3 When you have finished loading CDs the radio will begin to play the last CD loaded When a CD is inserted the CD symbol will be displayed If more than one CD has been loaded a number for each CD will be displayed If you select an equalization setting for your CD it will be activated each time you play a CD As each new track starts to play the track number will appear on the display Playing a Specific Loaded CD For every CD loaded a number will appear on the display To play a specific CD first press the CD AUX button then press the numbere
35. E Accessories Doing Your Own Service Work If you want to do some of your own service work you will want to use the proper service manual It tells you much more about how to service your vehicle than this manual an To order the proper servi 2 manual see Servieg Publications Ordering Informationjon page 7 13 Your vehicle has an air bag system Before attempting to do your own service work see Servicing Your Ai Bag Equipped Vehicle on page 1 77 You should keep a record with all parts receipts and list the mileage and the date of any service work you perform See on page 6 14 You can be injured and your vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it Be sure you have sufficient knowledge experience the proper replacement parts and tools before you attempt any vehicle maintenance task CAUTION Continued Be sure to use the proper nuts bolts and other fasteners English and metric fasteners can be easily confused If you use the wrong fasteners parts can later break or fall off You could be hurt Adding Equipment to the Outside of Your Vehicle Things you might add to the outside of your vehicle can affect the airflow around it This may cause wind noise and affect windshield washer performance Check with your dealer before adding equipment to the outside of your vehicle Fuel Use of the recommended fuel is an important part
36. Everyone 1 12 Safety CHAINS sanera sehr blu ENE EER 4 45 Safety Warnings and Symbols 0 ceeeeeeeeee ees iii Scheduled Maintenance eeeeeeeeeneeeeeneees 6 4 12 Seats Head Restraints gassen rr hen 1 5 Heated Seats ricsina as ev vee 1 3 Manual Lumbar sisdscs sc sencsce miesni heard ded 1 3 Manual Passenger s eeceeeeeeeeeceeeereeees 1 2 Rear Seat Operations sarte rense eii 1 6 Reclining Seatbacks W u ssseeeeeeeerere renerne renere 1 4 Six Way Power Seats ccceceeeeeeeeeeeeeees 1 2 Split Bench Seats 2 cee eee eee eee ee 1 6 Secondary Latch System ccceeeeeeeeeeeee tenes 5 85 Securing a Child Restraint Center Rear Seat Position eeeeeeeeee 1 56 Designed for the LATCH System 005 1 54 Rear Outside Seat Position eceeeeeeee 1 54 Right Front Seat Position aaeeea 1 59 Security Message PASS Key Il 2 3 48 Security While You Travel 0 ccceeeeeeeeeeeees 7 6 SENGE chic A E E E N 5 3 Adding Equipment to the Outside of Your Vehicle sss 52 hehe enegie 5 4 Doing Your Own Work sssssssssesssrserseresrrersrrrene 5 3 Engine Soon Light ceceeeeeeeeeneeeeeeeee ees 3 39 Publications Ordering Information 7 13 Traction System Warning Message 3 43 Vehicle Soon Message ceeeeeeeeeeeeeeeeeenes 3 51 Service Bulletins cceeceecee
37. If the cable is hanging turn the wrench clockwise to raise the cable back up Have the hoist assembly inspected as soon as you can You will not be able to store a spare tire using the hoist assembly until it has been repaired or replaced 5 88 Turn the wrench counterclockwise until approximately 6 inches 15 cm of cable is exposed Attach the folding wrench to the jack and raise the jack at least 10 turns Place the jack under the vehicle ahead of the rear bumper Position the center lift point of the jack under the center of the spare tire Turn the folding wrench clockwise to raise the jack until it lifts the secondary latch spring Keep raising the jack until the spare tire stops moving upward and is held firmly in place this lets you know that the secondary latch has released 5 89 6 Lower the jack by turning the folding wrench 7 Grasp the spare tire with both hands and pull it out counterclockwise Keep lowering the jack until from under the vehicle the spare tire is resting on the folding wrench 8 Reach under the vehicle and remove the folding wrench and jack 9 When the spare tire has been completely lowered tilt the retainer and slip it through the wheel opening 10 If the cable is hanging turn the wrench clockwise to raise the cable back up Have the hoist assembly inspected as soon as you can You will not be able to store a spare tire using the hoist assembly
38. Lock Brake System in this section In many emergencies steering can help you more than even the very best braking Traction Control System TCS Your vehicle may have a traction control system that limits wheel spin This is especially useful in slippery road conditions The system operates only if it senses that one or both of the front wheels are spinning or beginning to lose traction When this happens the system works the front brakes and reduces engine power to limit wheel spin The TRACTION ACTIVE message will come on when the traction control system is limiting wheel spin See Traction Active Message on page 3 44 You may feel or hear the system working but this is normal If your vehicle is in cruise control when the traction control system begins to limit wheel spin the cruise control will automatically disengage When road conditions allow you to safely use it again you may reengage the cruise control See Cruise Control under Turn Signal Multifunction Lever on page 3 8 SERVICE TC TRACTION Canada SYSTEM United States If this message comes on and stays on or comes on while you are driving there s a problem with your traction control system page 3 43 When this warning message is on the TRAC OFF light will come on to remind you that the system will not limit wheel spin Adjust your driving accordingly The traction control system automatically comes on whenever you start your
39. Preset PTYs RDS Only The six numbered pushbuttons let you return to your favorite PTYs These pushbuttons have factory PTY presets You can set up to 12 PTYs six FM1 and six FM2 by performing the following steps 1 Press BAND to select FM1 or FM2 2 Press PROG TYPE to activate program type select mode The PTY symbol will appear on the display 3 Turn the SELECT knob to select a PTY 4 Press and hold one of the six numbered pushbuttons until you hear a beep Whenever you press that numbered pushbutton the PTY you set will return if program type select mode is activated 5 Repeat the steps for each pushbutton RDS Messages ALERT Alert warns of national or local emergencies When an alert announcement comes on the current radio station ALERT will appear on the display You will hear the announcement even if the volume is muted or a CD is playing If a CD is playing play will stop during the announcement You will not be able to turn off alert announcements ALERT will not be affected by tests of the emergency broadcast system This feature is not supported by all RDS stations INFO Information If the current station has a message INFO will appear on the display Press this button to see the message The message may display the artist song title call in phone numbers etc 3 79 If the whole message is not displayed parts of the message will appear every three seconds To scroll through the message
40. States Please refer to the Warranty and Owner Assistance Information book Courtesy Transportation Pontiac has always exemplified quality and value in its offering of motor vehicles To enhance your ownership experience we and our participating dealers are proud to offer Courtesy Transportation a customer support program for new vehicles The Courtesy Transportation program is offered to retail purchase lease customers in conjunction with the Bumper to Bumper coverage provided by the New Vehicle Limited Warranty Several transportation options are available when warranty repairs are required This will reduce your inconvenience during warranty repairs Plan Ahead When Possible When your vehicle requires warranty service you should contact your dealer and request an appointment By scheduling a service appointment and advising your service consultant of your transportation needs your dealer can help minimize your inconvenience If your vehicle cannot be scheduled into the service department immediately keep driving it until it can be scheduled for service unless of course the problem is safety related If it is please call your dealership let them know this and ask for instructions If the dealer requests that you simply drop the vehicle off for service you are urged to do so as early in the work day as possible to allow for same day repair 7 8 Transportation Options Warranty service can generally be completed w
41. UQ3 Radio Amplifier Head Up Display Hazard Flashers Instrument Panel Cluster Climate Control Security LED and Remote Keyless Entry Module PASS Key III a Accessory Diode Body Control Module BCM Underhood Fuse Block partment on This fuse block is located in the engine com the passenger s side of the vehicle See Compartment Overview on page 5 12 for more information on location The back up lamp relay A is located to the left of the underhood fuse block To remove the cover press the two tabs in and lift up the cover 5 115 D oO oO s 088 8 Je Gs JR a ot 8 BEBE 8 888 8 el 9 ire z ei I oO oO O Fuel Pump Air Conditioning Compressor Clutch Horn Fuse Engine Controls Emissions and Sensors Power Control Module OO 7 O PCM Battery Power Anti Lock Brake System ABS Control Module Transaxle Solenoids 5 116 Anti lock Brake System ABS Solenoid Valves Oxygen Sensors Emissions Control Ignition Relay Neutral Start Switch Powertrain Control Module PCM Body Control Module BCM Battery Power All Wheel Drive AWD Module Cruise Control Fuse Usage __ Automatic Transaxle Shift Lock Control System Main Battery Fuse for Retained 41 Accessory Power Relay and Accessory Relay 42 Main Battery Fuse for Heated Seats Air Main Battery Fuse for Power 45 Outlets Level Control Po
42. by any bony structure This alone could cause serious or fatal injuries Young children always should be secured in appropriate child restraints Child Restraint Systems A rear facing infant seat B provides restraint with the seating surface against the back of the infant The An infant car bed A a special bed made for use in a harness system holds the infant in place and in a crash motor vehicle is an infant restraint system designed acts to keep the infant positioned in the restraint to restrain or position a child on a continuous flat surface Make sure that the infant s head rests toward the center of the vehicle 1 45 A forward facing child seat C E provides restraint for the child s body with the harness and also sometimes with surfaces such as T shaped or shelf like shields 1 46 A booster seat F G is a child restraint designed to improve the fit of the vehicle s safety belt system Some booster seats have a shoulder belt positioner and some high back booster seats have a five point harness A booster seat can also help a child to see out the window Q How do child restraints work A A child restraint system is any device designed for use in a motor vehicle to restrain seat or position children A built in child restraint system is a permanent part of the motor vehicle An add on child restraint system is a portable one which is purchased by the vehicle s owner For many years ad
43. can happen if you are steering through a sharp curve and you suddenly accelerate Those two control systems steering and acceleration can overwhelm those places where the tires meet the road and make you lose control See Traction Contro System TCS on page 4 10 What should you do if this ever happens Ease up on the brake or accelerator pedal steer the vehicle the way you want it to go and slow down Speed limit signs near curves warn that you should adjust your speed Of course the posted speeds are based on good weather and road conditions Under less favorable conditions you will want to go slower If you need to reduce your speed as you approach a curve do it before you enter the curve while your front wheels are straight ahead Try to adjust your speed so you can drive through the curve Maintain a reasonable steady speed Wait to accelerate until you are out of the curve and then accelerate gently into the straightaway Steering in Emergencies There are times when steering can be more effective than braking For example you come over a hill and find a truck stopped in your lane or a car suddenly pulls out from nowhere or a child darts out from between parked cars and stops right in front of you You can avoid these problems by braking if you can stop in time But sometimes you can not there is not room That is the time for evasive action steering around the problem Your vehicle ca
44. cer hannen bare era s 4 24 Before Leaving on a Long Trip c dsseee 4 25 Highway Hypnosis eccerre 4 26 Hill and Mountain Roads 4 26 Winter DIVINO ereinen iaaa 4 28 If You Are Stuck In Sand Mud Ice or Snow 4 33 TOWING 2 abs lonse nn eedebs e 4 34 Towing Your Vehicle cceceeeeeeeeee eee ee nents 4 34 Recreational Vehicle Towing 0 eeeeeeeeee 4 34 Loading Your Vehicle cseeeeeeeeeeeeeee 4 36 Towing a Trailer caerse an una dermed 4 42 Your Driving the Road and Your Vehicle Whenever we drive we are taking on an important responsibility This is true for any motor vehicle passenger car van truck sport utility Driver behavior the driving environment and the vehicle s design all affect how well a vehicle performs But statistics show that the most important factor by far is how we drive Knowing how these three factors work together can help you understand how your vehicle handles and what you can do to avoid many types of crashes including a rollover crash Driver Behavior The single most important thing is this everyone in the vehicle including the driver should buckle up See Safety Belts They Are for Everyonejon page 1 12 In fact most serious injuries and fatalities to unbelted occupants can be reduced or prevented by the use of safety belts Ina rollover crash an unbelted person is significantly more likely to die than a person wear
45. elapsed time of the track FWD gt Forward Press and hold this button to advance quickly within a track You will hear sound at a reduced volume Release the button to play the passage The display will show the elapsed time of the track RPT Repeat With repeat you can repeat one track or an entire CD To use repeat do the following To repeat the track you are listening to press and release the RPT button RPT will appear on the display Press RPT again to turn off repeat play To repeat the CD you are listening to press and hold the RPT button for two seconds RPT will appear on the display Press RPT again to turn off repeat play 3 99 RDM Random With random you can listen to the tracks in random rather than sequential order on one CD or on all of the CDs To use random do one of the following To play the tracks on the CD you are listening to in random order press and release the RDM button RANDOM ONE will appear on the display Press RDM again to turn off random play To play the tracks on all of the CDs that are loaded in random order press and hold RDM for more than two seconds You will hear a beep and RANDOM ALL will appear on the display Press RDM again to turn off random play AUTO EQ Automatic Equalization Press AUTO EQ to select the desired equalization setting while playing a CD The equalization will be automatically set whenever you play a CD For more information on AUTO E
46. identified as meeting GM Standard GM6094M and have the starburst symbol on the front of the oil container Notice Use only engine oil identified as meeting GM Standard GM6094M and showing the American Petroleum Institute Certified For Gasoline Engines starburst symbol Failure to use the recommended oil can result in engine damage not covered by your warranty GM Goodwrench oil meets all the requirements for your vehicle If you are in an area of extreme cold where the temperature falls below 20 F 29 C it is recommended that you use either an SAE 5W 30 synthetic oil or an SAE OW 30 oil Both will provide easier cold starting and better protection for your engine at extremely low temperatures Engine Oil Additives Do not add anything to your oil The recommended oils with the starburst symbol that meet GM Standard GM6094M are all you will need for good performance and engine protection When to Change Engine Oil GM Oil Life System Your vehicle has a computer system that lets you know when to change the engine oil and filter This is based on engine revolutions and engine temperature and not on mileage Based on driving conditions the mileage at which an oil change will be indicated can vary considerably For the oil life system to work properly you must reset the system every time the oil is changed When the system has calculated that oil life has been diminished it will indicate that an oil change is necess
47. increase injury The shoulder belt should fit against your body 1 21 Q What s wrong with this A The belt is buckled in the wrong place 1 22 You can be seriously injured if your belt is buckled in the wrong place like this In a crash the belt would go up over your abdomen The belt forces would be there not at the pelvic bones This could cause serious internal injuries Always buckle your belt into the buckle nearest you Q What s wrong with this A The belt is over an armrest You can be seriously injured if your belt goes over an armrest like this The belt would be much too high In a crash you can slide under the belt The belt force would then be applied at the abdomen not at the pelvic bones and that could cause serious or fatal injuries Be sure the belt goes under the armrests 1 23 Q What s wrong with this You can be seriously injured if you wear the shoulder belt under your arm In a crash your body would move too far forward which would increase the chance of head and neck injury Also the belt would apply too much force to the ribs which aren t as strong as shoulder bones You could also severely injure internal organs like your liver or spleen The shoulder belt is worn under the arm It should be worn over the shoulder at all times 1 24 Q What s wrong w
48. kke ebbe 3 119 Cleaning Aluminum or Chrome Plated Wheels 5 108 Cleaning Exterior Lamps Lenses 0 00665 5 107 Cleaning Fabric Carpet ceceeeeeeeeeeee eee ees 5 103 Cleaning Glass Surfaces eceeeeeeeeeeeeee ees 5 105 Cleaning Interior Plastic Components 5 105 Cleaning Leather ccceceeeeeeeneeeeeneeeeenees 5 105 Cleaning the Top of the Instrument Panel 5 105 Cleaning TIKES ccceceeeeeeeeeeeeeeeeeeeen eee een ees 5 108 Cleaning Vinyl dadis anen nanan o a E ees 5 105 Cleaning Windshield and Wiper Blades 5 107 Climate Control System ccceceeeeeeeeeeee eee 3 24 DU Al soriire e E N 3 27 Outlet Adjustment 2 00 00 ceeeeeeeeeeeeeeee eee rener 3 30 Compact Spare Tire snersssmanicnisiis inemes 5 102 Compass Variance cceeeeeeeee eee eeeeeeeeeeeeneeaes 3 53 Console Cooler cccceeeeeeneeeeenee eee res 2 36 Content Theft Deferrent eeeeeeeeeeeeeeeeeenes 2 14 Control of a Vehicle cc ceeeeeeeeeeeeeeeeeee een eees 4 7 Convenience Net ceeceeeeeeeeeneeeeeeeeeeaeeaes 2 41 Convenience Tray Sliding Rear eceeeeee 2 43 Coolant Engine Temperature Gage eeeeeeeeneee ees 3 39 Engine Temperature Warning Message 3 44 Heater Engine aciccssesecccscsaaecsscngandsaneinenessdeniee 2 21 Cooling System 52 rada ap EO NEED ANSE 5 28 Cruise Control 125 ea aks 3 10
49. lamps will not turn on at the same instant that the ignition is turned to OFF 15 The headlamps and parking lamps will stay on for 15 seconds when the ignition is turned to OFF 30 The headlamps and parking lamps will stay on for 30 seconds when the ignition is turned to OFF 60 The headlamps and parking lamps will stay on for 60 seconds when the ignition is turned to OFF Your vehicle was originally programmed to 30 second mode The mode may have been changed since then To determine the current mode or to change the mode do the following 1 Follow the instructions for Entering Programming Mode listed previously 2 Press the MODE button until HEADLAMP EXIT DELAY appears in the DIC 3 Press the SET button until the arrow is before the mode you prefer 3 58 The mode you selected is now set You can either exit programming mode by following the instructions later in this section or program the next feature available on your vehicle Interior Lighting Delay The interior lighting delay feature can be programmed to one of the following modes OFF This feature will not illuminate the interior of your vehicle when all of the doors are closed ON This feature will continue to illuminate the interior lamps for 25 seconds after all doors have been closed so that you can find your ignition and buckle your safety belt at night Interior lighting delay will not occur while the ignition is in ON After 25 seconds t
50. left knob clockwise or counterclockwise to increase or decrease the fan speed Turn the knob to OFF to turn off the fan The fan must be turned on for the air conditioning compressor to operate ra Outside Air Press this button to turn the outside air mode on or off When this mode is on outside air will circulate throughout your vehicle When this mode is on an indicator light in the button will come on to let you know that it is activated The outside air mode can be used with all modes but it cannot be used with the recirculation mode CS Recirculation This mode keeps outside air from coming in the vehicle It can be used to prevent outside air and odors from entering your vehicle or help heat or cool the air inside your vehicle more quickly Press this button to turn the recirculation mode on or off When the button is pressed an indicator light will come on The air conditioning compressor also comes on The recirculation mode can be used with vent and bi level modes but it cannot be used with floor defog defrost or outside air modes Temperature Control Turn the center knob clockwise or counterclockwise to increase or decrease the air temperature inside your vehicle A C Air Conditioning Press this button to turn the air conditioning system on or off When A C is pressed an indicator light in the button will come on to let you know that air conditioning is activated You may notice a slight change in en
51. less than two seconds to advance at 10 times the normal playing speed Press and hold it for more than two seconds to advance at 20 times the normal playing speed Release the pushbutton to play the track The display will show FWD and the elapsed time of the track RDM 2 Random To repeat the tracks in the current folder or playlist press and release this pushbutton FOLDER RANDOM will appear on the display Once all of the tracks in the current folder or playlist have been played the system will move on to the next folder or playlist and play all of the tracks in random order To repeat the tracks on the CD press and hold this pushbutton for two seconds You will hear a beep and CD RANDOM will appear on the display This feature will not work with playlists When in random pressing and releasing either SEEK arrow will take you to the next or previous random track Press and release this pushbutton again to turn off random play NO RANDOM will appear on the display 3 LA Next Folder Press this pushbutton to go to the first track in the next folder or playlist If the CD contains playlists it will go through the playlist then the folders Pressing this button while in folder random mode will take you to the next folder and random the tracks in that folder This function will not work on a disc that does not contain folders or playlists 4 REV Reverse Press and hold this pushbutton to reverse quickly within
52. life coolant The following explains your cooling system and how to add coolant when it is low If you have a problem with engine overheating see Engine Overheating on page 5 25 A 50 50 mixture of clean drinkable water and DEX COOL coolant will e Give freezing protection down to 34 F 37 C Give boiling protection up to 265 F 129 C Protect against rust and corrosion Help keep the proper engine temperature Let the warning messages and gages work as they should Notice Using coolant other than DEX COOL may cause premature engine heater core or radiator corrosion In addition the engine coolant may require changing sooner at 30 000 miles 50 000 km or 24 months whichever occurs first Any repairs would not be covered by your warranty Always use DEX COOL silicate free coolant in your vehicle What Coolant to Use Use a mixture of one half clean drinkable water and one half DEX COOL coolant which won t damage aluminum parts If you use this coolant mixture you don t need to add anything else Adding only plain water to your cooling system can be dangerous Plain water or some other liquid such as alcohol can boil before the proper coolant mixture will Your vehicle s coolant warning system is set for the proper coolant mixture With plain water or the wrong mixture your engine could get too hot but you would not get the overheat warning Your engine could catch fire and you or oth
53. of the vehicle to increase lumbar support Turn the knob toward the rear of the vehicle to decrease lumbar support Heated Seats wo Your vehicle may have heated seats If it does the heated seat switches are located in the instrument panel switchbank This feature will quickly heat the seat cushions and lower back of the driver s and front passenger s seat The left switch is for the driver s seat and the right switch is for the front passenger s seat Press the top of the switch to turn the heater on Press the bottom of the switch to turn the heater off The heated seat switch will turn off when the ignition is turned to OFF and will resume operation when the ignition is turned to ON unless the switch is turned off Reclining Seatbacks To adjust the seatback pull up on the recliner lever located on the outboard sides of both the driver s and front passenger s seats Release the lever to lock the seatback where you want it Push and pull on the seat to make sure it s locked into position Pull up on the lever and the seat will go to its original upright position But don t have a seatback reclined if your vehicle is moving Sitting in a reclined position when your vehicle is in motion can be dangerous Even if you buckle up your safety belts can t do their job when you re reclined like this The shoulder belt can t do its job because it won t be against your body Instead it will be in front of yo
54. on page 5 1T0 Your vehicle has a basecoat clearcoat paint finish The clearcoat gives more depth and gloss to the colored basecoat Always use waxes and polishes that are non abrasive and made for a basecoat clearcoat paint finish Notice Machine compounding or aggressive polishing on a basecoat clearcoat paint finish may damage it Use only non abrasive waxes and polishes that are made for a basecoat clearcoat paint finish on your vehicle Foreign materials such as calcium chloride and other salts ice melting agents road oil and tar tree sap bird droppings chemicals from industrial chimneys etc can damage your vehicle s finish if they remain on painted surfaces Wash the vehicle as soon as possible If necessary use non abrasive cleaners that are marked safe for painted surfaces to remove foreign matter Exterior painted surfaces are subject to aging weather and chemical fallout that can take their toll over a period of years You can help to keep the paint finish looking new by keeping your vehicle garaged or covered whenever possible Cleaning Windshield and Wiper Blades If the windshield is not clear after using the windshield washer or if the wiper blade chatters when running wax sap or other material may be on the blade or windshield Clean the outside of the windshield with a full strength glass cleaning liquid The windshield is clean if beads do not form when you rinse it with water Grime f
55. one take 1 to 20 minutes depending on e tempe re and vehicle use See A l Whee Drive Disable anne Message on page 3 49 Steering Power Steering If you lose power steering assist because the engine stops or the system is not functioning you can steer but it will take much more effort Steering Tips Driving on Curves It is important to take curves at a reasonable speed A lot of the driver lost control accidents mentioned on the news happen on curves Here is why Experienced driver or beginner each of us is subject to the same laws of physics when driving on curves The traction of the tires against the road surface makes it possible for the vehicle to change its path when you turn the front wheels If there is no traction inertia will keep the vehicle going in the same direction If you have ever tried to steer a vehicle on wet ice you will understand this The traction you can get in a curve depends on the condition of your tires and the road surface the angle at which the curve is banked and your speed While you are in a curve speed is the one factor you can control Suppose you are steering through a sharp curve Then you suddenly apply the brakes Both control systems steering and braking have to do their work where the tires meet the road Unless you have four wheel anti lock brakes adding the hard braking can demand too much of those places You can lose control The same thing
56. out of the filler neck reinstall the pressure cap Be sure the arrows on the pressure cap line up like this 9 Then fill the coolant recovery tank to the FULL COLD mark 10 Put the cap back on the coolant recovery tank Power Steering Fluid Cli The power steering fluid reservoir is located to the right of the windshield washer fluid reservoir at the back of the engine compartment 5 35 When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise A fluid loss in this system could indicate a problem Have the system inspected and repaired See Engine Compartment Overvie on page 5 12 for reservoir location How to Check Power Steering Fluid To check the power steering fluid do the following 1 Turn the engine off and let the engine compartment cool down 2 Wipe the cap and the top of the reservoir clean and then unscrew the cap 3 Wipe the dipstick with a clean rag then remove the cap again and look at the fluid level on the dipstick 4 Replace the cap and completely tighten it When the engine compartment is hot the level should be at the H hot mark When it is cold the level should be at the C cold mark If the fluid is at the ADD mark you should add fluid 5 36 What Power eee Fluid to Use To ermine wha kind of flui e see on page 6 12 Always use the proper fluid
57. prior to any root directory folders However playlists Px will always be accessed before root folders or files Empty Directory or Folder If a root directory or a folder exists somewhere in the file structure that contains only folders subfolders and no compressed files directly beneath them the player will advance to the next folder in the file structure that contains compressed audio files and the empty folder will not be displayed or numbered No Folder When the CD contains only compressed files the files will be located under the root folder The next and previous folder functions will have no function on a CD that was recorded without folders or playlists When displaying the name of the folder the radio will display ROOT When the CD contains only playlists and compressed audio files but no folders all files will be located under the root folder The folder down and the folder up buttons will search playlists Px first and then go to the root folder When the radio displays the name of the folder the radio will display ROOT Order of Play Tracks will be played in the following order Play will begin from the first track in the first playlist and will continue sequentially through all tracks in each playlist When the last track of the last playlist has been played play will continue from the first track of the first playlist Ifthe CD does not contain any playlists then play will begin from the first track u
58. refueling your vehicle this is against the law in some places Keep children away from the fuel pump never let children pump fuel The fuel cap is located on the driver s side of the vehicle While refueling let the fuel cap hang by the tether as shown To remove the fuel cap turn it slowly to the left counterclockwise The fuel cap has spring in it if you let go of the cap too soon it will spring back to the right If you spill fuel and then something ignites it you could be badly burned Fuel can spray out on you if you open the fuel cap too quickly This spray can happen if your tank is nearly full and is more likely in hot weather Open the fuel cap slowly and wait for any hiss noise to stop Then unscrew the cap all the way Be careful not to spill fuel Don t top off or overfill your tank and wait a few seconds after you ve finished pumping before you remove the nozzle Clean fuel from painted surfaces as soon as possible clang the Outside of Your Vehicle on page 5 106 When you put the fuel cap back on turn it to the right Filling a Portable Fuel Container clockwise until you hear a clicking sound Make sure you fully install the cap The diagnostic system can determine if the fuel cap has been left off or improperly installed This would allow fuel to evaporate into the atmosphere See Malfunction Indicator Lamp on page 3 39 Never fill a portable fuel container while it is in
59. seconds and then pull it back out again 3 Check both sides of the dipstick and read the lower level The fluid level must be in the cross hatched area 4 If the fluid level is in the acceptable range push the dipstick back in all the way 5 21 How to Add Automatic Transaxle Fluid Refer to the Maintenance Schedule to determine what kind of transaxle fluid to use See Fluids and Lubricants on page 6 12 If the fluid level is low add only enough of the proper fluid to bring the level into the cross hatched area on the dipstick 1 Pull out the dipstick 2 Using a long neck funnel add enough fluid at the dipstick hole to bring it to the proper level It does not take much fluid generally less than one pint 0 5 L Do not overfill Notice We recommend you use only fluid labeled DEXRON Ill because fluid with that label is made especially for your automatic transmission Damage caused by fluid other than DEXRON III is not covered by your new vehicle warranty 3 After adding fluid recheck the fluid level as described under How to Check Automatic Transaxle Fluid 4 When the correct fluid level is obtained push the dipstick back in all the way 5 22 Engine Coolant The cooling system in your vehicle is filled with DEX COOL engine coolant This coolant is designed to remain in your vehicle for 5 years or 150 000 miles 240 000 km whichever occurs first if you add only DEX COOL extended
60. start this procedure at Step 2 approximately 6 inches 15 cm of cable is exposed 2 Attach the folding wrench to the jack and raise the jack at least 10 turns 3 Place the jack under the vehicle ahead of the rear bumper Position the center lift point of the jack under the center of the spare tire 5 86 4 5 Turn the folding wrench clockwise to raise the jack until it lifts the secondary latch spring Keep raising the jack until the spare tire stops moving upward and is held firmly in place this lets you know that the secondary latch has released and the spare tire is balancing on the jack 6 Lower the jack by turning the folding wrench counterclockwise Keep lowering the jack until the spare tire slides off the jack 5 87 All Wheel Drive To release the spare tire from the secondary latch do the following Someone standing too close during the procedure could be injured by the jack If the spare tire does not slide off the jack completely make sure no one is behind you or on either side of you as you pull the jack out from the spare 7 Disconnect the wrench from the jack and carefully remove the jack Use one hand to push against the spare while firmly pulling the jack out from under the spare tire with the other hand If the cable is not visible start this procedure at Step 2 8 When the spare tire has been completely lowered tilt the retainer and slip it through the wheel opening 9
61. stored for a long period of time remove the batteries and keep them in a cool dry place Tips and Trouble Recommended Action No power Disc will not play No sound The ignition may not be in run accessory or RAP The parental control button might have been pressed The power Indicator light will flash The system might be off The parental control button might have been pressed The power indicator light will flash The system might be in auxiliary source mode Press the SRCE button to toggle between the DVD player and the auxiliary source The disc is upside down or is not compatible The volume on the headphones could be too low Adjust the volume on the right earpiece on the cordless headphones If the DVD system is being heard through the vehicle speakers adjust the volume from the radio The radio must have the RSE channel enabled by using the CD AUX button Recommended Action The picture is distorted during fast forward or reverse This is normal for this operation The picture does not fill the Quickly press and release screen There are black borders on the top and bottom or on both sides or it looks stretched out ejected the disc and tried to take it out but it was pulled back into the slot The language in the audio or on the screen is wrong The remote control does not work the display control button on the remote control or the DVD player and choose Dis
62. the AUDIO knob until BASS MID or TREB appears on the display Turn the knob to increase or to decrease If a station is weak or noisy you may want to decrease the treble To adjust bass midrange or treble to the middle position select BASS MID or TREB and push and hold the AUDIO knob The radio will produce one beep and adjust the display level to zero To adjust all tone and speaker controls to the middle position push and hold the AUDIO knob when no tone or speaker control is displayed The radio will produce one beep and CENTERED will appear on the display AUTO EQ Automatic Equalization Press this button to select customized bass midrange and treble equalization settings designed for country jazz talk pop rock and classical To return to the manual mode CUSTOM press the AUTO EQ button until CUSTOM appears on the display Then you will be able to manually adjust the bass midrange and treble using the AUDIO knob 3 92 Adjusting the Speakers Balance Fade AUDIO To adjust the balance between the right and the left speakers push the AUDIO knob until BAL appears on the display Turn the knob to move the sound toward the right or the left speakers To adjust the fade between the front and the rear speakers push and hold the AUDIO knob until FAD appears on the display Turn the knob to move the sound toward the front or the rear speakers To adjust the balance and the fade to the middle position sel
63. the Radio PWR Power Push this knob to turn the system on and off VOL Volume Turn this knob to increase or to decrease volume SCV Speed Compensated Volume With SCV your audio system adjusts automatically to make up for road and wind noise as you drive Set the volume at the desired level Press this button to select MIN MED or MAX Each higher setting allows for more volume compensation at faster vehicle speeds Then as you drive SCV automatically increases the volume as necessary to overcome noise at any speed The volume level should always sound the same to you as you drive If you don t want to use SCV select OFF RCL Recall Push this knob to switch the display between the radio station frequency and the time Pushing this knob with the ignition off will display the time For XMIM 48 contiguous US states if equipped push the RCL knob while in XM mode to retrieve four different categories of information related to the current song or channel Artist Song Title Category or PTY Channel Number Channel Name 3 66 To change the default on the display push the RCL knob until you see the display you want then hold the knob until the display flashes The selected display will now be the default Finding a Station BAND Press this button to switch between FM1 FM2 AM or XM1 or XM2 48 contiguous US states if equipped The display will show your selection TUNE Turn this knob to select radi
64. the remote keyless entry transmitter The interior lamp override is turned on There is no occupant activity detected for an illumination period of 25 seconds Your vehicle was originally programmed to DOOR The mode may have been changed since then To determine the current mode or to change the mode do the following 1 Follow the instructions for Entering Programming Mode listed previously 2 Press the MODE button until INTERIOR LIGHTING ON appears on the DIC 3 Press the SET button until the arrow is before KEY OUT or DOOR The mode you selected is now set You can either exit programming mode by following the instructions later in this section or program the next feature available on your vehicle 3 59 Auto Door Lock Unlock The doors will automatically lock when the vehicle is shifted out of PARK P For automatic unlocking you can program your vehicle to one of the following modes OFF When the shift lever is put in PARK P your doors will not unlock automatically DRIVER When the shift lever is put in PARK P only your driver s door will unlock ALL When the shift lever is put in PARK P all doors will unlock Your vehicle was originally programmed to ALL The mode may have been changed since then To determine the current mode or to change the mode do the following 1 Follow the instructions for Entering Programming Mode listed previously 2 Make sure that the AUTO DOOR LO
65. this book This safety symbol means Don t Don t do this or Don t let this happen Vehicle Damage Warnings Also in this book you will find these notices Notice These mean there is something that could damage your vehicle A notice will tell you about something that can damage your vehicle Many times this damage would not be covered by your warranty and it could be costly But the notice will tell you what to do to help avoid the damage When you read other manuals you might see CAUTION and NOTICE warnings in different colors or in different words You ll also see warning labels on your vehicle They use the same words CAUTION or NOTICE Vehicle Symbols Your vehicle has components and labels that use symbols instead of text Symbols used on your vehicle are shown along with the text describing the operation or information relating to a specific component control message gage or indicator If you need help figuring out a specific name of a component gage or indicator reference the following topics Seats and Restraint Systems in Section 1 Features and Controls in Section 2 Instrument Panel Overview in Section 3 Climate Controls in Section 3 Warning Lights Gages and Indicators in Section 3 Audio System s in Section 3 Engine Compartment Overview in Section 5 These are some examples of vehicle symbols you may find on your vehicle CAUTION POSSIBLE INJURY PROTECT
66. this button to turn the outside air mode on or off When this mode is on outside air will circulate throughout your vehicle When this mode is on an indicator light in the button will come on to let you know that it is activated The outside air mode can be used with all modes but it cannot be used with the recirculation mode A Recirculation This mode keeps outside air from coming in the vehicle It can be used to prevent outside air and odors from entering your vehicle or help heat or cool the air inside your vehicle more quickly Press this button to turn the recirculation mode on or off When the button is pressed an indicator light will come on The air conditioning compressor also comes on The recirculation mode can be used with vent and bi level modes but it cannot be used with floor defog defrost or outside air modes Temperature Control Use the driver s and passenger s temperature levers to increase or decrease the air temperature inside your vehicle AIC Air Conditioning Press this button to turn the air conditioning system on or off When A C is pressed an indicator light in the button will come on to let you know that air conditioning is activated 3 28 You may notice a slight change in engine performance when the air conditioning compressor shuts off and turns on again This is normal The system is designed to make adjustments to help with fuel economy while still maintaining the selected temperatu
67. user s guide in your vehicle s glove box or call OnStar at 1 888 4 ONSTAR 1 888 466 7827 OnStar Virtual Advisor With OnStar Virtual Advisor you can listen to the news entertainment and informative topics such as traffic and weather reports You are able to listen and reply to your e mail through your vehicle s speakers 2 33 Storage Areas Glove Box If the glove box has a lock put your key into the lock and turn the key counterclockwise To open the glovebox pull the latch release The glove box door has a detent to prevent the door from lowering too far Open the glove box until the door is partway open then pull the door down if you need it fully opened To close the glove box the door must be pushed up past the detent To lock the glovebox put your key into the lock and turn the key clockwise Cupholder s There are cupholders located in the center console next to the shift lever The cupholders have liners that remove for larger beverage items Remove the liners by lifting them out Store the liners in the glove box when not in use Your vehicle also has cupholders located in the rear passenger doors and the tailgate 2 34 Overhead Console If your vehicle has the overhead console it has a storage compartment a compartment for your garage door opener and a compartment for your sunglasses If your vehicle has the OnStar System the OnStar buttons will replace the front storage compar
68. vehicle Kilopascal kPa The metric unit for air pressure There are 6 9 kPa s to one psi Light Truck LT Metric Tire A tire used on light duty trucks and some multipurpose passenger vehicles Load Index An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire Maximum Inflation Pressure The maximum air pressure to which a cold tire may be inflated The maximum air pressure is molded onto the sidewall Maximum Load Rating The load rating for a tire at the maximum permissible inflation pressure for that tire Maximum Loaded Vehicle Weight The sum of curb weight accessory weight vehicle capacity weight and production options weight 5 64 Normal Occupant Weight The number of occupants a vehicle is designed to seat_multiplied by 150 pounds 68 kg See Loading Your Vehicle on page 4 36 Occupant Distribution Designated seating positions Outward Facing Sidewall The side of a asymmetrical tire that has a particular side that faces outward when mounted on a vehicle The side of the tire that contains a whitewall bears white lettering or bears manufacturer brand and or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire Passenger P Metric Tire A tire used on passenger cars and some light duty trucks and multipurpose vehicles Recommended Inflation Pressure oe manufacturer s recommended tire_in shown on the tir
69. vehicle To limit wheel spin especially in slippery road conditions you should always leave the system on But you can turn the traction control system off if you ever need to You should turn the system off if your vehicle ever gets stuck in sand mud or snow and rocking the vehicle is required To turn the system off TRAC press the TRAC OFF OFF button located on the instrument panel switchbank If the system is limiting wheel spin when you press the button the message will go off but the system will not turn off until there is no longer a current need to limit wheel spin The TRAC OFF light will come on to remind you the system is off You can turn the system back on at any time by pressing the button again The traction control system warning message should go off All Wheel Drive AWD System If your vehicle has all wheel drive AWD the AWD system operates automatically without any action required by the driver If the front drive wheels begin to slip the rear wheels will automatically begin to drive the vehicle as required There may be a slight engagement noise during hard use but this is normal During heavy AWD applications the engine torque may be reduced to protect AWD system components If the vehicle is exposed to extended heavy AWD usage the AWD system will shut itself off to protect the system from overheating When the system cools down the AWD system will activate itself again automatically this oe
70. ventilated with a comfortably cool interior Keep your eyes moving Scan the road ahead and to the sides Check your mirrors and your instruments frequently e If you get sleepy pull off the road into a rest service or parking area and take a nap get some exercise or both For safety treat drowsiness on the highway as an emergency 4 26 Hill and Mountain Roads Driving on steep hills or mountains is different from driving in flat or rolling terrain lf you drive regularly in steep country or if you are planning to visit there here are some tips that can make your trips safer and more enjoyable Keep your vehicle in good shape Check all fluid levels and also the brakes tires cooling system and transaxle These parts can work hard on mountain roads Know how to go down hills The most important thing to know is this let your engine do some of the slowing down Shift to a lower gear when you go down a steep or long hill If you do not shift down your brakes could get so hot that they would not work well You would then have poor braking or even none going down a hill You could crash Shift down to let your engine assist your brakes on a steep downhill slope Coasting downhill in NEUTRAL N or with the ignition off is dangerous Your brakes will have to do all the work of slowing down They could get so hot that they would not work well You would then have poor braking or even none going down a hill
71. while your emission controls may not work as well your fuel economy may not be as good and your engine may not run as smoothly This could lead to costly repairs that may not be covered by your warranty Notice Modifications made to the engine transaxle exhaust intake or fuel system of your vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria TPC can affect your vehicle s emission controls and may cause this light to come on Modifications to these systems could lead to costly repairs not covered by your warranty This may also result in a failure to pass a required Emission Inspection Maintenance test 3 40 This light should come on as a check to show you it is working when the ignition is on and the engine is not running If the light does not come on have it repaired This light will also come on during a malfunction in one of two ways Light Flashing A misfire condition has been detected A misfire increases vehicle emissions and may damage the emission control system on your vehicle Diagnosis and service may be required Light On Steady An emission control system malfunction has been detected on your vehicle Diagnosis and service may be required If the Light Is Flashing The following may prevent more serious damage to your vehicle e Reducing vehicle speed Avoiding hard accelerations Avoiding steep uphill grades If you are t
72. you do you could cut or damage the warming grid and the repairs wouldn t be covered by your warranty Do not attach a temporary vehicle license tape a decal or anything similar to the defogger grid Dual Climate Control System Your vehicle may have a dual climate control system With this system you can control the heating cooling and ventilation for your vehicle Operation Turn the right knob clockwise or counterclockwise to direct the airflow inside your vehicle To change the current mode select one of the following 7s Vent This mode directs air to the instrument panel outlets Wi Bi Level This mode directs half of the air to the instrument panel outlets then directs the remaining air to the floor outlets Cooler air is directed to the upper outlets and warmer air to the floor outlets td Floor This mode directs most of the air to the floor outlets Use this mode to send air to the rear of the vehicle Keep the area under the front seats free of objects that could obstruct airflow to the rear of the vehicle The right knob can also be used to select defog or defrost mode For more information see Defogging and Defrosting later in this section 8 Fan Turn the left knob clockwise or counterclockwise to increase or decrease the fan speed Turn the knob to OFF to turn off the fan The fan must be turned on for the air conditioning compressor to operate 3 27 len Outside Air Press
73. you hit a pothole Keep tires at the recommended pressure e Worn old tires can cause accidents If your tread is badly worn or if your tires have been damaged replace them Tire Sidewall Labeling Useful information about a tire is molded into its sidewall The examples below show a typical passenger car tire and a compact spare tire sidewall Passenger Car Tire Example A Tire Size The tire size code is a combination of letters and numbers used to define a particular tire s width height aspect ratio construction type and service description See the Tire Size illustration later in this section for more detail B Tire Performance Criteria Specification TPC Spec Original equipment tires designed to GM s specific tire performance criteria have a TPC specification code molded onto the sidewall GM s TPC specifications meet or exceed all federal safety guidelines C Department of Transportation DOT The Department of Transportation DOT code indicates that the tire is in compliance with the U S Department of Transportation Motor Vehicle Safety Standards D Tire Identification Number TIN The letters and numbers following DOT code are the Tire Identification Number TIN The TIN shows the manufacturer and plant code tire size and date the tire was manufactured The TIN is molded onto both sides of the tire although only one side may have the date of manufacture 5 59 E Tire Ply
74. you turn it off Your PASS Key III system however is not working properly and must be serviced by your dealer Your vehicle is not protected by the PASS Key III system at this time If you lose or damage a PASS Key III key see your dealer who can service PASS Key III to have a new key made Starting and Operating Your Vehicle New Vehicle Break In Notice Your vehicle does not need an elaborate break in But it will perform better in the long run if you follow these guidelines If you have all wheel drive keep your speed at 55 mph 88 km h or less for the first 500 miles 805 km Do not drive at any one speed fast or slow for the first 500 miles 805 km Do not make full throttle starts Avoid making hard stops for the first 200 miles 322 km or so During this time your new brake linings are not yet broken in Hard stops with new linings can mean premature wear and earlier replacement Follow this breaking in guideline every time you get new brake linings Do not tow a trailer during break in See Towing a Trailer on page 4 42 for more information Ignition Positions With the key in the ignition you can turn the key to four different positions A OFF This is the only position in which you can remove the key This position locks the steering wheel ignition and transaxle Notice If your key seems stuck in OFF and you can t turn it be sure you are using the correct key
75. you turn the ignition key to ON If the anti lock brake system warning light stays on longer than normal after you ve started your engine turn the ignition off Or if the light comes on and stays on when you re driving stop as soon as possible and turn the ignition off Then start the engine again to reset the system If the light still stays on or comes on again while you re driving the anti lock brake system needs service and you don t have anti lock brakes The anti lock brake system warning light should come on briefly when you turn the ignition key to ON If the light doesn t come on then have it fixed so it will be ready to warn you if there is a problem 3 37 Traction Control System TCS e If there s an engine related and brake system problem that is specifically related to traction control Warning Light the traction control system will turn off and the warning light will come on If the traction control system warning light comes on and stays on for an extended period of time when the TRAC system is turned on your vehicle needs service OFF United States Canada Your vehicle may have a traction control system warning light The traction control system warning light may come on for the following reasons e If you turn the system off by pressing the TRAC OFF button located in the instrument panel switchbank the warning light will come on and stay on To turn the system back on press the button again The
76. your vehicle Static electricity discharge from the container can ignite the gasoline vapor You can be badly burned and your vehicle damaged if this occurs To help avoid injury to If a fire starts while you are refueling do not you and others remove the nozzle Shut off the flow of fuel by shutting off the pump or by notifying the station attendant Leave the area immediately e Dispense gasoline only into approved containers Do not fill a container while it is inside a vehicle in a vehicle s trunk pickup bed or on any surface other than the ground The malfunction indicator lamp SERVICE ENGINE SOON or CHECK ENGINE light will come on if the fuel Bring the fill nozzle in contact with the cap is not properly installed inside of the fill opening before operating the nozzle Contact should be maintained Notice If you need a new fuel cap be sure to get until the filling is complete the right type Your dealer can get one for you Do not smoke while pumping gasoline If you get the wrong type it may not fit properly This may cause your malfunction indicator lamp to light and may damage your fuel tank and emissions system See Malfunction Indicator Lamp in the Index Checking Things Under the Hood An electric fan under the hood can start up and injure you even when the engine is not running Keep hands clothing and tools away from any underhood electric fan Things that burn can get on hot eng
77. 118 Rear Seat Entertainment System 3 103 DVD Message S eitan eE 3 108 DVD Player as ar ne ser de DE sner dese anne 3 106 Electrical System Add On Equipment 22 5 112 Fuses and Circuit Breakers 5 113 Headlamp WIIG srt ber erne cee e es 5 112 Power Windows and Other Power Options 5 112 Windshield Wiper Fuses eeeeeeeeee 5 112 Emissions Inspection and Maintenance Programs eeceeeeeeeeee eee ee 3 42 Engine Air Cleaner Filter cccceceeeeeeeeeeeeeeeeeeees 5 18 Battery arrene aean EAE 5 41 Engine cont Change Oil Message W G ssssseveeeerere renerne nere 3 46 Check and Service Engine Soon Light 3 39 COOKE EF E A E ERE 5 22 Coolant Heater 155 522 sekserne 2 21 Coolant Temperature Gage ssseeeeereee 3 39 Coolant Temperature Warning Message 3 44 Drive Belt Routing asinsrites trenie 6 13 Engine Compartment Overview 1eeee 5 12 EXMAUSE oki IE Ehe noes renee 2 29 OFRER ER es SEES ORE ieee Sead E ELSE 5 13 Overheating isaer snini naianei ainich 5 25 Stanin sas eee ie eni En Ea enaa 2 20 Engine Oil Additives u sssseeeeeeeereeerrnnrnnee 5 16 Engine Specifications cceeeeeeeeeeeeeeeee eens 5 119 Entering Programming Mode scce 3 57 Entertainment System Cleaning the Video Screen see 3 119 Cleaning Your DVD Player oaeee 3 119 DYD DIStOMIOMN sisccstnnticazceasteccnentteantacshesenetd 3 118
78. 12 for more information Low Washer Fluid Warning Message LOW WASHER FLUID United States Canada If your washer fluid is low the warning message will come on and stay on until you add washer fluid See Windshield Washer Fluid on page 5 36 for adding washer fluid instructions If the warning message is still on after adding fluid you need to reset the warning message To reset the warning message turn the ignition off and then back on If the message stays on see your dealer 3 49 Low Fuel Warning Message LOW FUEL United States Canada If your fuel is low the warning message will come on and stay on until you add fuel If the warning message is still on after adding fuel you need to reset the warning message To reset the warning message turn the ignition off and then back on If the message stays on see your dealer 3 50 Low Brake Fluid Warning Message Canada United States If your brake fluid is low the warning message will come on and stay on until you add brake fluid The brake system warning light will also be illuminated If this message appears the brakes need attention You should have your vehicle serviced immediately See on page 3 36 and Brakes on page 5 38 If the warning message is still on after adding fluid you may need to reset the warning message To reset the warning message turn the ignition off and then back on If the message stays on see your dealer rig
79. 2004 Pontiac Aztek Owner Manual M Seats and Restraint Systems 006 1 1 Driving Your Vehicle 0ccceeseeeeeeeeees 4 1 Front Seats eniinn narn ENEE 1 2 Your Driving the Road and Your Vehicle _ 4 2 Rear Seats cciscicdsisweicencdicandaacideiaevecadiaediaass 1 6 TOWING seepeale EREA 4 34 Safety Bels eaea a r aii EE 1 12 Service and Appearance Cale Here eee er 5 1 Child Restraints peceren 1 39 Semice herreria arune erre aa baked 5 3 Air Bag Systems 1 W W G ssssssseseeeeeeeekrknnnner 1 61 Fiel an ea A EA 5 4 Restraint System Check 1 M W ssssneeerererrrere 1 71 Checking Things Under the Hood _ 5 10 Features and Controls 0e0sceeeeeeeeeeeees 2 1 All Wheel Drive oo ecccceceecececeeceeceseeeenes 5 48 KEYS eaea tins a tacatines cuca epee teenies 2 2 Bulb Replacement o oo cece ec cee eee cence eens 5 50 Doors and LOCKS ooo eee eeecececeeeeceeeeeeeees 2 7 Windshield Wiper Blade Replacement _ 5 56 Windows oa ee cece eee cec eee eee eee eeeeeee eee eeeeeeeees 2 12 TOS SE ES ES Eee 5 58 Theft Deterrent Systems W W u d dsssseeeeeee 2 14 Appearance Care GG Gssssssseseeeeeeeee ennen nknnen 5 103 Starting and Operating Your Vehicle 2 18 Vehicle Identification 2 5 111 MinrOrS seordenp seni eaaa SUE SNE REESE REESE 2 31 Electrical System oo etern h ek ner RE 5 112 OnStar System oo ceeeeeceeeeeesss
80. 5 50 Headphones ereis ane toe gse vinnie E SDN 3 103 Head Up Display HUD eee eee eee 3 20 Heated Seats 32252 re ener ee eee rane 1 3 Highway Hypnosis ersero 4 26 Hill and Mountain Roads ceeeeeeeeeeeeeee eens 4 26 Pehe S enose Erai a tered aina 4 45 Hood Checking Things Under eeeeeeeee eee ee 5 10 Release rr ENE desea tata cies 5 11 PONM ener acim serra cad ES ER REDER SEE REESE 3 7 How to Add Automatic Transaxle Fluid 5 22 How to Add Coolant to the Coolant Recovery Tank c eeeeeeeeeeeeeeeeee 5 30 How to Add Coolant to the Radiator 5 32 How to Check cceceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 5 66 How to Check Automatic Transaxle Fluid 5 20 How to Check Power Steering Fluid 5 36 How to Inspect the Engine Air Cleaner Filter 5 18 How to Use This Manual ceeeeeeeeeee neers iii How to Wear Safety Belts Properly W 1 W W 1 18 FIYOFOPIANING ccc veewccnesdincacieetmcdeeteavederseesetel ints 4 21 If No Steam Is Coming From Your Engine 5 27 If Steam Is Coming From Your Engine 5 26 If the Light Is Flashing c cc br keen 3 40 If the Light Is On Steady ceceeeeeeee teeter anes 3 41 If You Are Caught in a Blizzard ss 4 31 If You Are Stuck in Sand Mud Ice or Snow 4 33 If You Do Decide To Pull A Trailer 00 4 43 Ig
81. 8 4 ONSTAR 1 888 466 7827 or press the blue OnStar button to speak to an OnStar advisor 24 hours a day 7 days a week A completed Subscription Service Agreement is required prior to delivery of OnStar services and prepaid calling minutes are also required for OnStar Personal Calling and OnStar Virtual Advisor use Terms and conditions of the Subscription Service Agreement can be found at www onstar com 2 32 OnStar Services One of the following plans is normally included for a specific duration with each vehicle equipped with OnStar You can upgrade or extend your OnStar service plan to meet your needs Safe and Sound Plan Automatic Notification of Air Bag Deployment e Emergency Services Roadside Assistance Stolen Vehicle Assistance e AccidentAssist Remote Door Unlock e Remote Diagnostics Online Concierge Directions and Connections Plan All Safe and Sound Plan services Route Support e RideAssist Information and Convenience Services Luxury and Leisure Plan All Directions and Connections Plan services Personal Concierge OnStar Personal Calling With OnStar Personal Calling you have a safer way to stay connected while driving It s a hands free wireless phone that s integrated into your vehicle You can place calls nationwide using voice activated dialing with no contracts and no additional roaming charges To find out more about OnStar Personal Calling refer to the OnStar
82. A Won t I be trapped in the vehicle after an accident if I m wearing a safety belt You could be whether you re wearing a safety belt or not But you can unbuckle a safety belt even if you re upside down And your chance of being conscious during and after an accident so you can unbuckle and get out is much greater if you are belted If my vehicle has air bags why should I have to wear Safety belts Air bags are in many vehicles today and will be in most of them in the future But they are supplemental systems only so they work with safety belts not instead of them Every air bag system ever offered for sale has required the use of safety belts Even if you re in a vehicle that has air bags you still have to buckle up to get the most protection That s true not only in frontal collisions but especially in side and other collisions If Pm a good driver and never drive far from home why should wear safety belts You may be an excellent driver but if you re in an accident even one that isn t your fault you and your passengers can be hurt Being a good driver doesn t protect you from things beyond your control such as bad drivers Most accidents occur within 25 miles 40 km of home And the greatest number of serious injuries and deaths occur at speeds of less than 40 mph 65 km h Safety belts are for everyone How to Wear Safety Belts Properly This part is only for people of adult s
83. A two digit number that indicates the tire height to width measurements For example if the tire size aspect ratio is 70 as shown in item C of the illustration it would mean that the tire s sidewall is 70 as high as it is wide D Construction Code A letter code is used to indicate the type of ply construction in the tire The letter R means radial ply construction the letter D means diagonal or bias ply construction and the letter B means belted bias ply construction E Rim Diameter Diameter of the wheel in inches F Service Description These characters represent the load range and the speed rating of a tire The load range represents the load carrying capacity a tire is certified to carry The load index can range from 1 to 279 The speed rating is the maximum speed a tire is certified to carry a load Speed ratings range from A to Z Tire Terminology and Definitions Air Pressure The amount of air inside the tire pressing outward on each square inch of the tire Air pressure is expressed in pounds per square inch psi or kilopascal kPa Accessory Weight This means the combined weight of optional accessories Some examples of optional accessories are automatic transmission power steering power brakes power windows power seats and air conditioning Aspect Ratio The relationship of a tire s height to its width Belt A rubber coated layer of cords that is located
84. AN gt Press and hold either SCAN arrow for two seconds until SC appears on the display and you hear a beep The radio will go to a station play for a few seconds then go on to the next station Press either SCAN arrow again to stop scanning To scan preset stations press and hold either SCAN arrow for more than four seconds PRESET SCAN will appear on the display You will hear a double beep The radio will go to the first preset station stored on your pushbuttons play for a few seconds then go on to the next preset station Press either SCAN arrow again to stop scanning presets The radio will scan only to stations that are in the selected band and only to those with a strong signal Setting Preset Stations The six numbered pushbuttons let you return to your favorite stations You can set up to 30 stations six FM1 six FM2 and six AM six XM1 and six XM2 48 contiguous US states if equipped by performing the following steps 1 Turn the radio on 2 Press BAND to select FM1 FM2 AM or XM1 or XM2 3 Tune in the desired station 4 Press AUTO EQ to select the equalization 5 Press and hold one of the six numbered pushbuttons until you hear a beep Whenever you press that numbered pushbutton the station you set will return and the equalization that you selected will be automatically stored for that pushbutton 6 Repeat the steps for each pushbutton 3 91 Setting the Tone Bass Treble AUDIO Push
85. CK feature is programmed to ON 3 Press the MODE button until AUTO DOOR UNLOCK appears on the DIC 4 Press the SET button until the arrow is before OFF DRIVER or ALL 3 60 If the auto door unlock feature has been programmed to DRIVER or ALL the automatic door unlock feature can also be programmed to one of the following modes PARK All doors will unlock when the shift lever is put in PARK P KEY OUT All doors will unlock when the ignition key is removed Your vehicle was originally programmed to PARK The mode may have been changed since then To determine the current mode or to change the mode do the following 1 Follow the instructions for Entering Programming Mode listed previously 2 Follow the instructions for programming AUTO DOOR UNLOCK to DRIVER or ALL listed previously 3 Press the MODE button until AUTO DOOR UNLOCK PARK KEYOUT appears on the DIC 4 Press the SET button until the arrow is before PARK or KEY OUT The mode you selected is now set You can either exit programming mode by following the instructions later in this section or program the next feature available on your vehicle Delayed Locking The delayed locking feature can be programmed to one of the following modes ON Lock your vehicle using the power door lock switch or the remote keyless transmitter while any door is opened you will hear three chimes and the doors will not lock Five seconds after the last door i
86. Cap Hole C Folding Wrench Assembly ee Hoist Shaft D Extension Tube 1 Push the release lever located in front of the handle of the sliding rear tray to release the pin from the floor track assembly 2 Pull the sliding rear tray toward you without lifting it up 5 83 9 To remove the compact spare tire from the cable tilt the retainer and slip it through the wheel opening 10 After removing the spare tire turn the wrench clockwise to raise the cable back up Do not store a full size or a flat road tire under the vehicle See Storing a Flat Vehicles without the Sliding Rear Convenience Tray and Storing a Flat Vehicles with the Sliding Rear Convenience Tray later in this section To continue changing the flat tire see Removing the Flat Tire and Installing the Spare Tire later in this section 5 84 If the spare tire will not lower the secondary latch may be engaged causing the tire not to lower Do the following to check the cable ib 2 Check under the vehicle to see if the cable is visible If it s not visible see Secondary Latch System following If it is visible first try to tighten the cable by turning the folding wrench clockwise until you hear two clicks or feel it skip twice You cannot over tighten the cable 3 4 Then loosen the cable by turning the wrench counterclockwise three or four turns If the spare tire has not lowered tighten the ca
87. Consult with your retail location Playing a CD With the ignition on insert a CD partway into the slot label side up The player will pull it in and the CD should begin playing If you want to insert a CD when the ignition is off first press the eject button or push the RCL knob If you insert a CD with the radio off and the ignition on it will start to play When the CD is inserted the CD symbol will be displayed If you select an EQ setting for your CD it will be activated each time you play a CD If you turn off the ignition or radio with a CD in the player it will stay in the player When you turn on the ignition or radio the CD will start playing where it stopped if it was the last selected audio source As each new track starts to play the track number will appear on the display The CD player can play the smaller 8cm single CDs with an adapter ring Full size CDs and the smaller CDs are loaded in the same manner If playing a CD R the sound quality may be reduced due to CD R quality the method of recording the quality of the music that has been recorded and the way the CD R has been handled You may experience an increase in skipping difficulty in finding tracks and or difficulty in loading and ejecting If these problems occur try a known good CD Do not add paper labels to CDs they could get caught in the CD player Do not play 3 inch CDs without a standard adapter CD If an error appears on the displa
88. Cupholder S necis eias eas 2 34 Current and Past Model Order Forms 7 14 Customer Assistance Information Courtesy Transportation ssseneneeerrree 7 8 Customer Assistance for Text Telephone TTY Users ccceeeeeeeeeee es 7 4 Customer Assistance Offices ss 7 4 Customer Satisfaction Procedure 068 7 2 GM Mobility Program for Persons with Disabilities cccccccceeeeee eee eee eee ees 7 6 Reporting Safety Defects to General Motors 7 12 Reporting Safety Defects to the Canadian Government 0eeeeeeee 7 12 Reporting Safety Defects to the United States Government 7 11 Roadside Assistance Program eccerre 7 6 Service Publications Ordering Information 7 13 Daytime Running Lamps DRL cecce 3 14 Defensive Driving ecceeeeeeeeeeeteeeeeeeeeeeeeees 4 3 Defogging and Defrosting eee 3 26 3 29 Delayed Lighting ss isccsieieincccanceciats senses ienie iiin 3 17 Delayed Locking eeeeeeeeereeeeeeeeeees 2 8 3 61 Dinghy TOWING eeren enrere iite ela n ea 4 35 Disarming with the Remote Keyless Enthy Transmiter e piceae a 2 15 Disarming with Your Key 22 urene 2 15 Doing Your Own Service Work sseseeeererererere 5 3 Dolly TOWING scsisviwcscciccneg Mowsiegney satine 4 35 Door Ajar Warning Message eseeeeeeeeeee neers 3 47 Delayed LOcking resines ai seed 2 8 LOCKS ae
89. DVD or CD is playing to freeze the video and mute the audio The video screen will display Parental Control On and the power indicator light on the DVD player will flash It will also disable all other button operations from the remote control and the DVD player with the exception of the eject button The driver will then be able to gain the attention of the rear seat passengers Press this button again to restore normal operation of the DVD player and remote control This button may also be used to turn the DVD player power on and automatically resume play if the vehicle is in an enabled power mode Playing a Disc To play a disc gently insert the disc with the label side up into the loading slot The DVD player will continue loading the disc and the player will automatically start if the vehicle is in run accessory or RAP If a disc is already in the player make sure that the DVD player is on then press the play pause button on the player faceplate or on the remote control 3 107 Some DVDs will not allow you to fast forward or skip the copyright information or previews Some DVDs will begin playing after the previews have finished If the DVD does not begin playing at the main title refer to the on screen instructions Stopping and Resuming Playback To stop playing a disc press and release the stop button on the DVD player faceplate or the remote control To resume playback press the play pause button on the DVD pla
90. Engine Compartment Overview on page 5 12 for the location of the engine air cleaner filter When to Inspect the Engine Air Cleaner Filter Inspect the air cleaner filter at every oil change and replace it at the first oil change after 25 000 miles 40 000 km See Scheduled Maintenance on page 6 4 for more information How to Inspect the Engine Air Cleaner Filter To inspect the air cleaner filter remove the filter from the vehicle and lightly shake the filter to release loose dust and dirt If the filter remains caked with dirt a new filter is required To inspect or replace the air cleaner filter do the following 1 Remove the two clamps on the duct 2 Remove the duct 3 Unlatch the two hooks on top of the engine air cleaner filter housing 4 Remove and replace the engine air cleaner filter 5 Align the tabs located on the bottom of the panel with the slots at the bottom of the housing 6 Latch the hooks to secure the panel in place If the panel moves easily check that the tabs are seated correctly in the slots 7 Put the duct back on and reinstall the clamps Operating the engine with the air cleaner filter off can cause you or others to be burned The air cleaner not only cleans the air it helps to stop flame if the engine backfires If it is not there and the engine backfires you could be burned Do not drive with it off and be careful working on the engine with the air cleaner filter off
91. L PRICE 120 00 Transmission Transaxle Transfer Case Unit Repair Manual This manual provides information on unit repair service procedures adjustments and specifications for GM transmissions transaxles and transfer cases RETAIL SELL PRICE 50 00 Service Bulletins Service Bulletins give technical service information needed to knowledgeably service General Motors cars and trucks Each bulletin contains instructions to assist in the diagnosis and service of your vehicle In Canada information pertaining to Product Service Bulletins can be obtained by contacting your General Motors dealer or by calling 1 800 GM DRIVE 1 800 463 7483 Owner s Information Owner publications are written specifically for owners and intended to provide basic operational information about the vehicle The owner s manual will include the Maintenance Schedule for all models In Portfolio Includes a Portfolio Owner s Manual and Warranty Booklet RETAIL SELL PRICE 35 00 Without Portfolio Owner s Manual only RETAIL SELL PRICE 25 00 Current and Past Model Order Forms Service Publications are available for current and past model GM vehicles To request an order form please specify year and model name of the vehicle ORDER TOLL FREE 1 800 551 4123 Monday Friday 8 00 AM 6 00 PM Eastern Time For Credit Card Orders Only VISA MasterCard Discover visit Helm Inc on the World Wide Web at www helminc com Or you can write t
92. Malfunction Indicator 22 22222 sr eee ee 3 39 Safety Belt Reminder 0 eseeeeeeeneeeeeees 3 35 TCS Warning Light ccceeeeeeeeeeeeeeeeeee ees 3 38 Traction Control System TCS Warning 3 38 Loading Your Vehicle e csceeneeeeeeeeeeeees 4 36 Lock Feedback 5222 eee eee 3 63 8 Lockout Protection nd 2 10 Locks Delayed LOCKING aar anii 2 8 DOOF renee nes eler 2 7 Leaving Your Vehicle ceceeeeeeeeeeeee ees 2 10 Lockout Protection eeeeeeeeeeeeeeeeeeees 2 10 POWER DOOM zoo erne le bene 2 8 Programmable Automatic Door Locks 2 9 Rear Door Security LOCKS eeeeeeeee eee 2 9 LOSS Of COmtrol nj cccseiciestnectedsecapsdeetadenciecmeciaed ace 4 16 Low Brake Fluid Warning Message 4 3 50 Low Fuel Warning Message 0 eeeeeeeeeeee 3 50 Low Oil Pressure Message 0seeeeeeeeeeeeees 3 45 Low Tire Message ccceeeeeeeeeeneceeeeeeeeeeeees 3 47 Low Washer Fluid Warning Message 3 49 Lumbar Manual Controls cceeeeeeeeeeeeeeeeeeeeeneeeees 1 3 Maintenance Schedule Additional Required Services ceeeeeeeee ee 6 6 At Each Fuel ER aa A EIA 6 8 At Least Once a Month ccccccceeeeeeeees 6 9 At Least Once a Year cccc cece cece ec eeeeeeeeeees 6 9 Intro dust ON seinci sinisa merien anoni febr deb 6 2 Maintenance Footnotes ccce
93. Material The type of cord and number of plies in the sidewall and under the tread F Uniform Tire Quality Grading UTQG Tire manufacturers are required to grade tires based on three performance factors treadwear traction and temperature resistance For more information see RY USE 0 Unitorm Tire Qualty Grading on page 5 72 oAPRY USE om a G Maximum Cold Inflation Load Limit Maximum load that can be carried and the maximum pressure needed to support that load For_more information on recommended tire pressure see nflation Tire Pressure on page 5 66 and Loading Your Vehicle on page 4 36 en ra Py aD 9 m o 5 gt Ssauq xwwigd 0 antowan 8 G w a Q ia lt N CY y 09 Of Sv 71aN Compact Spare Tire Example 5 60 A Temporary Use Only The compact spare tire or temporary use tire has a tread life of approximately 3 000 miles 5 000 km and should not be driven at speeds over 65 mph 105 km h The compact spare tire is for emergency use when a regular road tire has lost air and gone flat Seel Compact Spare Tire on page 5 102 and f a Tire Goes Flatton page 5 77 B Tire Ply Material The type of cord and number of plies in the sidewall and under the tread C Tire Identification Number TIN The Tire Identification Number TIN The TIN shows the manufacturer and plant code tire size and date the tire was manufactured The TIN is molded onto both sides of t
94. NE AVG ECON 5 9 65 F L 100 KM If your vehicle is equipped with the Driver Information Center DIC the display is located on the instrument panel cluster directly above the steering column The DIC will show information about the vehicle and the surroundings The DIC has a compass display to show you which direction the vehicle is driving Compass Variance Compass variance is the difference between magnetic north and geographic north In some areas of the country the difference is great enough to cause the compass to give false readings If this occurs the compass must be set Automatic Compass Calibration The compass is self calibrating which eliminates the need to manually set the compass When the vehicle is new the calibration process may not be complete In these cases the calibration symbol C will be displayed where the compass reading is normally displayed To calibrate the compass in an area free from large metal objects make three 360 degree turns The calibration symbol will turn off and the compass reading will be displayed 3 53 Manual Compass Calibration If the compass appears erratic and the calibration symbol does not appear you must manually put the compass into the calibration mode To get into this mode do the following 1 Turn the ignition on and cycle the DIC to the compass temperature mode 2 Press and hold the SET button for longer then three seconds 3 54 ZONE
95. Notice If the air cleaner filter is off a backfire can cause a damaging engine fire And dirt can easily get into your engine which will damage it Always have the air cleaner filter in place when you re driving Automatic Transaxle Fluid When to Check and Change Automatic Transaxle Fluid A good time to check your automatic transaxle fluid level is when the engine oil is changed Change both the fluid and filter every 50 000 miles 83 000 km if the vehicle is mainly driven under one or more of these conditions In heavy city traffic where the outside temperature regularly reaches 90 F 32 C or higher In hilly or mountainous terrain When doing frequent trailer towing Uses such as found in taxi police or delivery service If you do not use your vehicle under any of these conditions change the fluid and filter at 100 000 miles 166 000 km See Scheduled Maintenance on page 6 4 for more information 5 20 How to Check Automatic Transaxle Fluid Because this operation can be a little difficult you may choose to have this done at the dealership service department If you do it yourself be sure to follow all the instructions here or you could get a false reading on the dipstick Notice Too much or too little fluid can damage the transaxle Too much can mean that some of the fluid could come out and fall on hot engine or exhaust system parts starting a fire Too little fluid could cause the transax
96. PRESS amp HOLD SET TO CHANGE This display mode will be displayed when you are manually calibrating the system The current zone number for compass variance will be displayed in place of the symbol Use the SET button to select the zone number from the graphic shown to select the current area of the country that you are driving in PRESS SET TO CALIBRATE COMPASS After selecting your zone press the MODE button and this will be displayed on the DIC Press the SET button and complete three 360 degree turns in an area free from large metal objects The following two messages will toggle in the display until you calibrate the compass DRIVE VEHICLE IN CIRCLE CALIBRATING COMPASS When calibration is complete the display will return to its normal mode DIC Controls and Displays When the ignition is turned to ON or START the DIC will display the following PONTIAC PONTIAC will be displayed for three seconds DRIVER This message will be displayed for three seconds after PONTIAC appears in the display This message lets you know which remote keyless entry and customization features the vehicle is using The DIC controls are located to the right of the instrument panel cluster DRIVER INFO CENTER The DIC will be in the last mode displayed when the engine was turned off To select a different mode press MODE The display will cycle through its options at each press of MODE MODE This button lets you cycle t
97. Q see AUTO EQ listed previously in this section K SEEK gt I Press the left arrow to go to the start of the current track if more than ten seconds have passed Press the right arrow to go to the next track If you hold an arrow or press it more than once the player will continue moving backward or forward through the CD 3 100 K SCAN gt To scan one CD press and hold either SCAN arrow for more than two seconds until SCAN appears on the display and you hear a beep Use this feature to listen to 10 seconds of each track of the currently selected CD Press either SCAN arrow again to stop scanning To scan all loaded CDs press and hold either SCAN arrow for more than four seconds until CD SCAN appears on the display and you hear a beep Use this feature to listen to 10 seconds of the first tracks of each CD loaded Press either SCAN arrow again to stop scanning RCL Recall Press this knob to see how long the current track has been playing To change the default on the display track and elapsed time press the knob until you see the display you want then hold the knob until the display flashes The selected display will now be the default BAND Press this button to play the radio when a CD s is playing The inactive CD will remain safely inside the radio for future listening CD AUX Auxiliary Press this button to play a CD when listening to the radio Using Song List Mode The six CD CD changer has a
98. RDRIVE D Here are some times you might choose THIRD 3 instead of AUTOMATIC OVERDRIVE D When driving on hilly winding roads e When towing a trailer so there is less shifting between gears e When going down a steep hill SECOND 2 This position gives you more power but lower fuel economy than THIRD 3 You can use SECOND 2 on hills It can help control your speed as you go down steep mountain roads but then you would also want to use your brakes off and on 2 24 Notice Driving in SECOND 2 for more than 25 miles 40 km or at speeds over 55 mph 90 km h may damage the transaxle Also shifting into SECOND 2 at speeds above 65 mph 105 km h can cause damage Drive in THIRD 3 or AUTOMATIC OVERDRIVE D instead of SECOND 2 Notice If your vehicle seems to start up rather slowly or if it seems not to shift gears as you go faster something may be wrong with a transaxle system sensor If you drive very far that way your vehicle can be damaged So if this happens have your vehicle serviced right away Until then you can use SECOND 2 when you are driving less than 35 mph 55 km h and THIRD 3 for higher speeds FIRST 1 This position gives you even more power but lower fuel economy than SECOND 2 You can use it on very steep hills or in deep snow or mud If the shift lever is put in FIRST 1 the transaxle will not downshift into first gear until the vehicle is going slow enough Noti
99. RIVER 1 or DRIVER 2 Each transmitter may be programmed differently for each driver s preferences After you press the LOCK button on your transmitter and the ignition key is in ON the DIC will display the identified driver number The vehicle will also recall the vehicle customization features that were last programmed to correspond to your transmitter lf you unlock your vehicle using your key instead of your transmitter the DIC will not change drivers and your vehicle will recall the information from the last transmitter used Entering Programming Mode To program features your vehicle must be in the programming mode Do the following 1 Turn the ignition key to ON with the vehicle in PARK P 2 Press and release the MODE button then scroll through the DIC messages until PRESS SET TO BEGIN PERSONALIZATION is displayed 3 Press the SET button and TO SELECT DRIVER PRESS REMOTE LOCK will appear Press the LOCK button on the remote keyless entry This identifies which remote keyless entry transmitter is being programmed by displaying PERSONALIZATION FOR DRIVER 1 or DRIVER 2 PROGRAM MODE United States Canada 4 The program mode message will appear in the message center as an indication that your vehicle is ready to begin programming 5 Follow the instructions given by the DIC 3 57 Headlamp Exit Delay This feature allows you to customize the headlamps and parking lamps OFF The headlamps and parking
100. Stop Taillamps B Back up Lamps Unscrew the bulb socket from the lamp assembly by pressing the tab while turning the bulb socket counterclockwise Replace the bulb by pulling the old one out and gently pushing the new one into the bulb socket Line up the tabs on the bulb socket with the gaps in the socket holes and screw the bulb socket back into the lamp housing You will hear a click To reinstall align the pins on the back of the lamp with the sockets on the outboard side of the lamp opening Push forward until the pins snap into the socket Reinstall the screws removed in Step 2 Replacement Bulbs Bulb Number Back up Lamps Bottom 3155K Headlamps High beam 9005 Headlamps Low beam 9006 Front Turn Signal Parking Sidemarker Lamps 3057 Stop Taillamps Top 3057K 5 55 Windshield Wiper Blade Replacement Windshield wiper blades should be inspected at least twice a year for wear or cracking See Wiper Blade Check under Owner Checks and Services on page 6 8 for more information Replacement blades come in different types and are removed in different ways For proper type and length see Normal Maintenance Replacement Parts on page 6 T3 5 56 Here s how to remove the wiper blades 1 Turn the wipers on to the lowest intermittent setting 2 Turn off the ignition while the wipers are at the outer positions of the wipe pattern The blades are more accessible for removal replac
101. T Press this button to eject a CD Eject may be activated with either the ignition or radio off CDs may be loaded with the radio and ignition off if this button is pressed first CD Messages CHECK CD If this message appears on the radio display and the CD comes out it could be for one of the following reasons Itis very hot When the temperature returns to normal the CD should play You are driving on a very rough road When the road becomes smoother the CD should play The CD is dirty scratched wet or upside down The air is very humid If so wait about an hour and try again The format of the CD may not be compatible See MP3 Format earlier in this section There may have been a problem while burning the CD The label may be caught in the CD player If the CD is not playing correctly for any other reason try a known good CD If any error occurs repeatedly or if an error cannot be corrected contact your dealer If your radio displays an error message write it down and provide it to your dealer when reporting the problem Radio with Six Disc CD Radio Data System RDS Your audio system is equipped with a Radio Data System RDS RDS features are available for use only on FM stations that broadcast RDS information With RDS your radio can do the following Seek to stations broadcasting the selected type of programming Receive announcements concerning local and national emerg
102. When raising your vehicle on a jack avoid contact with the rear axle control arms Do not raise the vehicle yet Put the compact spare tire near you Getting under a vehicle when it is jacked up is dangerous If the vehicle slips off the jack you could be badly injured or killed Never get under a vehicle when it is supported only by a jack Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall To help avoid personal injury and vehicle damage be sure to fit the jack lift head into the proper location before raising the vehicle 4 Attach the folding wrench to the jack and turn the wrench clockwise to raise the jack head 3 inches 7 6 cm Raise the vehicle by turning the folding wrench clockwise in the jack Raise the vehicle far enough off the ground so there is enough room for the spare tire to fit under the wheel well Remove all the wheel nuts and take off the flat tire 5 93 5 94 7 Remove any rust or dirt from the wheel bolts mounting surfaces and spare wheel Rust or dirt on the wheel or on the parts to which it is fastened can make the wheel nuts become loose after a time The wheel could come off and cause an accident When you change a wheel remove any rust or dirt from the places where the wheel attaches to the vehicle In an emergency you can use a cloth or a paper towel to do this but be sure to use a scraper or wire
103. Ys six FM1 and six FM2 by performing the following steps 1 Press BAND to select FM1 or FM2 2 Press the P TYPE button to activate program type select mode P TYPE and the last selected PTY will appear on the display 3 Turn the P TYPE knob to select a PTY 4 Press and hold one of the six numbered pushbuttons until you hear a beep Whenever you press that numbered pushbutton the PTY you set will return 5 Repeat the steps for each pushbutton RDS Messages ALERT Alert warns of local or national emergencies When an alert announcement comes on the current radio station ALERT will appear on the display You will hear the announcement even if the volume is muted or a CD is playing If a CD is playing play will stop during the announcement You will not be able to turn off alert announcements ALERT will not be affected by tests of the emergency broadcast system This feature is not supported by all RDS stations 3 94 INFO Information If the current station has a message INFO will appear on the display Press this button to see the message The message may display the artist song title call in phone numbers etc If the whole message is not displayed parts of the message will appear every three seconds To scroll through the message at your own speed press the INFO button repeatedly A new group of words will appear on the display with each press Once the complete message has been displayed INFO will di
104. a track Press and hold this pushbutton for less than two seconds to reverse at 10 times the normal playing speed Press and hold it for more than two seconds to reverse at 20 times the normal playing speed Release the pushbutton to play the track The display will show REV and the elapsed time of the track If this button is pressed for more than 20 seconds the radio will stop reversing and begin to play 6 Previous Folder Press this pushbutton to go to the first track in the previous folder or playlist If the CD contains playlists it will go through the playlist then the folders Pressing this button while in folder random mode will take you to the previous folder and random the tracks in that folder This function will not work on a disc that does not contain folders or playlists 3 87 A SEEK V Press the up arrow to go to the start of the next track Press the down arrow to go to the start of the previous track Pressing either arrow for more than 2 seconds will search the previous or next tracks at 2 tracks per second When you see the track number that you would like to play release the button to stop searching and to play the track TUNE Turn this knob to fast track reverse or advance through tracks in all folders or playlists The track number and file name will appear on the display for each track Turn this knob while in random to fast track reverse or advance the tracks in sequential order RCL Recall Push thi
105. able service experts in GM dealerships all across North America They will be ready and willing to help if you need it Here are some things you can check before a trip e Windshield Washer Fluid s the reservoir full Are all windows clean inside and outside e Wiper Blades Are they in good shape e Fuel Engine Oil Other Fluids Have you checked all levels Lamps Are they all working Are the lenses clean e Tires They are vitally important to a safe trouble free trip Is the tread good enough for long distance driving Are the tires all inflated to the recommended pressure e Weather Forecasts What is the weather outlook along your route Should you delay your trip a short time to avoid a major storm system Maps Do you have up to date maps 4 25 Highway Hypnosis Is there actually such a condition as highway hypnosis Or is it just plain falling asleep at the wheel Call it highway hypnosis lack of awareness or whatever There is something about an easy stretch of road with the same scenery along with the hum of the tires on the road the drone of the engine and the rush of the wind against the vehicle that can make you sleepy Do not let it happen to you If it does your vehicle can leave the road in ess than a second and you could crash and be injured What can you do about highway hypnosis First be aware that it can happen Then here are some tips Make sure your vehicle is well
106. ada 89021186 DEXRON III Automatic Transmission Fluid Automatic Transaxle Usage Fluid Lubricant Multi Purpose Lubricant Superlube GM Part No U S 12346241 in Canada 10953474 Key Lock Cylinders Carrier Assembly Differential Rear Drive Module and Transfer Case Power Transfer Unit Hood Latch Assembly Lubriplate Lubricant Aerosol Secondary GM Part No U S 12346293 in Latch Pivots Canada 992723 or lubricant Spring Anchor meeting requirements of NLGI 2 and Release Category LB or GC LB Pawl Hood and Door Multi Purpose Lubricant Superlube Hinges Rear GM Part No U S 12346241 in Folding Seat Canada 10953474 f Dielectric Silicone Grease Weatherstrip GM Part No U S 12345579 in 9 Canada 992887 VERSATRAK Fluid GM Part No U S 12378514 in Canada 88901045 Normal Maintenance Replacement Parts po Pat i GM Part Number ACDelco Part Number Engine Air Cleaner Filter Engine Oil Filter Share EOE Windshield Wiper Blades Driver s Side Length 24 0 inches 60 0 cm Passenger s Side Length 22 0 inches 55 0 cm Shepherd s Hook Engine Drive Belt Routing 6 13 Maintenance Record After the scheduled services are performed record the date odometer reading who performed the service and the type of services performed in the boxes provided See on page 6 2 in this section Any additional information from on page 6 8 can be added on the fol
107. ailable No Info No Text Informational message available Not Found No channel available for the chosen category XM Locked Theft lock active Radio ID Radio ID label channel 0 Unknown Radio ID not known should only be if hardware failure Chk XMRcevr Hardware failure 3 72 XM Radio Messages cont d Action Required No artist information is available at this time on this channel Your system is working properly No song title information is available at this time on this channel Your system is working properly No category information is available at this time on this channel Your system is working properly No text or informational messages are available at this time on this channel Your system is working properly There are no channels available for the category you selected Your system is working properly The XM receiver in your vehicle may have previously been in another vehicle For security purposes XM receivers cannot be swapped between vehicles If you receive this message after having your vehicle serviced check with the servicing facility If you tune to channel 0 you will see this message alternating with your XM Radio 8 digit radio ID label This label is needed to activate your service If you receive this message when you tune to channel 0 you may have a receiver fault Consult with your dealer If this message does not clear within a short period of time your receiver may have a fault
108. aking very sharp turns while trailering When you are turning with a trailer make wider turns than normal Do this so your trailer will not strike soft shoulders curbs road signs trees or other objects Avoid jerky or sudden maneuvers Signal well in advance Turn Signals When Towing a Trailer When you tow a trailer your vehicle has to have extra wiring The arrows on your instrument panel will flash whenever you signal a turn or lane change Properly hooked up the trailer lamps will also flash telling other drivers you are about to turn change lanes or stop When towing a trailer the arrows on your instrument panel will flash for turns even if the bulbs on the trailer are burned out Thus you may think drivers behind you are seeing your signal when they are not It s important to check occasionally to be sure the trailer bulbs are still working 4 47 Driving On Grades Parking on Hills Reduce speed and shift to a lower gear before you start down a long or steep downgrade If you do not shift down you might have to use your brakes so much that they would get hot and no longer work well If you are towing a trailer that weighs more than You really should not park your vehicle with a 1 000 Ibs 450 kg drive in THIRD 3 instead of trailer attached on a hill If something goes AUTOMATIC OVERDRIVE D or as you need to a wrong your rig could start to move People lower gear This will minimize heat build up and
109. an ease alittle to the right Loss of Control Let us review what driving experts say about what happens when the three control systems brakes steering and acceleration do not have enough friction where the tires meet the road to do what the driver has asked In any emergency do not give up Keep trying to steer and constantly seek an escape route or area of less danger Skidding In a skid a driver can lose control of the vehicle Defensive drivers avoid most skids by taking reasonable care suited to existing conditions and by not overdriving those conditions But skids are always possible The three types of skids correspond to your vehicle s three control systems In the braking skid your wheels are not rolling In the steering or cornering skid too much speed or steering in a curve causes tires to slip and lose cornering force And in the acceleration skid too much throttle causes the driving wheels to spin A cornering skid is best handled by easing your foot off the accelerator pedal If you have the Traction Control System remember It helps avoid only the acceleration skid If you do not have this system or if the system is off then an acceleration skid is also best handled by easing your foot off the accelerator pedal If your vehicle starts to slide ease your foot off the accelerator pedal and quickly steer the way you want the vehicle to go If you start steering quickly enough your vehicle may s
110. an use THIRD 3 or as you need to a lower gear when towing a trailer Operating your vehicle in THIRD 3 when towing a trailer will minimize heat buildup and extend the life of your transaxle Three important considerations have to do with weight e Weight of the trailer e Weight of the trailer tongue e Weight on your vehicle s tires Weight of the Trailer How heavy can a trailer safely be It should never weigh more than 1 400 Ibs 630 kg with up to five occupants in the vehicle or more than 2 000 Ibs 900 kg with up to two occupants If you have the optional trailer towing package your vehicle can tow up to 2 900 Ibs 1 300 kg with up to five occupants or up to 3 500 Ibs 1 575 kg with up to two occupants But even that can be too heavy It depends on how you plan to use your rig For example speed altitude road grades outside temperature and how much your vehicle is used to pull a trailer are all important And it can also depend on any special equipment that you have on your vehicle You can ask your dealer for our trailering information or advice or you can write us at Pontiac GMC Customer Assistance Center P O Box 33172 Detroit MI 48232 5172 In Canada write to General Motors of Canada Limited Customer Communication Centre 163 005 1908 Colonel Sam Drive Oshawa Ontario L1H 8P7 4 43 Weight of the Trailer Tongue The tongue load A of any trailer is an important weight to measure beca
111. ap according to the child restraint instructions 5 Push and pull the child restraint in different directions to be sure it is secure To remove the child restraint simply unhook the top strap from the top tether anchor and then disconnect the anchor points 1 54 Securing a Child Restraint in a Rear Outside Seat Position If Gal child re nt is equipped with the LATCH ec Lowe F R horages and Top Tethers fo Children LA ystem on page T Top Strap on page 1 49 if the child restraint has one If your child restraint does not have the LATCH system you will be using the lap shoulder belt to secure the restraint in this position Be sure to follow the instructions that came with the child restraint Secure the child in the child restraint when and as the instructions say 1 Put the restraint on the seat 2 Pick up the latch plate and run the lap and shoulder portions of the vehicle s safety belt through or around the restraint The child restraint instructions will show you how Tilt the latch plate to adjust the belt if needed 3 Buckle the belt Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to 4 To tighten the belt pull up on the shoulder belt while you push down on the child restraint If you are using a forward facing child restraint you may find it helpful to use you knee to push down on the child restraint as you tighten the
112. ar safety belts Here s why They work things inside the vehicle or be ejected from it You can be seriously injured or killed In the same crash you might not be if you are buckled up Always fasten your safety belt and check that your passengers belts are fastened properly too You never know if you ll be in a crash If you do have a crash you don t know if it will be a bad one A few crashes are mild and some crashes can be so serious that even buckled up a person wouldn t survive But most crashes are in between In many of them people who buckle up can survive and sometimes walk away Without belts they could have been badly hurt or killed After more than 30 years of safety belts in vehicles the facts are clear In most crashes buckling up does matter a lot Why Safety Belts Work When you ride in or on anything you go as fast as it goes Take the simplest vehicle Suppose it s just a seat on wheels Put someone on it Get it up to speed Then stop the vehicle The rider doesn t stop The person keeps going until stopped by something or the instrument panel In a real vehicle it could be the windshield or the safety belts With safety belts you slow down as the vehicle does You get more time to stop You stop over more distance and your strongest bones take the forces That s why safety belts make such good sense Questions and Answers About Safety Belts Q
113. art to accelerate but stay in the right lane and do not get too close Time your move so you will be increasing speed as the time comes to move into the other lane If the way is clear to pass you will have a running start that more than makes up for the distance you would lose by dropping back And if something happens to cause you to cancel your pass you need only slow down and drop back again and wait for another opportunity If other vehicles are lined up to pass a slow vehicle wait your turn But take care that someone is not trying to pass you as you pull out to pass the slow vehicle Remember to glance over your shoulder and check the blind spot Check your mirrors glance over your shoulder and start your left lane change signal before moving out of the right lane to pass When you are far enough ahead of the passed vehicle to see its front in your inside mirror activate your right lane change signal and move back into the right lane Remember that your right outside mirror is convex The vehicle you just passed may seem to be farther away from you than it really is Try not to pass more than one vehicle at a time on two lane roads Reconsider before passing the next vehicle Do not overtake a slowly moving vehicle too rapidly Even though the brake lamps are not flashing it may be slowing down or starting to turn Ifyou are being passed make it easy for the following driver to get ahead of you Perhaps you c
114. arts If you don t it could be damaged How long should you keep the coolant heater plugged in The answer depends on the outside temperature the kind of oil you have and some other things Instead of trying to list everything here we ask that you contact your dealer in the area where you ll be parking your vehicle The dealer can give you the best advice for that particular area 2 21 Automatic Transaxle Operation Maximum engine speed is limited when you re in PARK P or NEUTRAL N to protect driveline components from improper operation There are several different positions for your shift lever PARK P This gear position locks your front wheels It s the best position to use when you start your engine because your vehicle cannot move easily Ensure the shift lever is fully in PARK P before starting the engine Your vehicle has an automatic transaxle shift lock control system You must fully apply your regular brakes before you can shift from PARK P when the ignition key is in ON As you step on the brake pedal while in PARK P you may hear a click from the solenoid of the system This ensures that the system is operating properly 2 22 If you cannot shift out of PARK P ease pressure on the shift lever push the shift lever all the way into PARK P as you maintain brake application Then hold the button on the lever and move the shift lever into the gear you wish See Shifting Out of Park P
115. ary A CHANGE ENGINE OIL message will come on Change your oil as soon as possible within the next two times you stop for fuel It is possible that if you are driving under the best conditions the oil life system may not indicate that an oil change is necessary for over a year However your engine oil and filter must be changed at least once a year and at this time the system must be reset Your dealer has GM trained service people who will perform this work using genuine GM parts and reset the system It is also important to check your oil regularly and keep it at the proper level lf the system is ever reset accidentally you must change your oil at 3 000 miles 5 000 km since your last oil change Remember to reset the oil life system whenever the oil is changed How to Reset the CHANGE ENGINE OIL Message The GM Oil Life System calculates when to change your engine oil and filter based on vehicle use Anytime your oil is changed reset the system so it can calculate when the next oil change is required If a situation occurs where you change your oil prior to a CHANGE ENGINE OIL message being turned on reset the system If your vehicle does not have the optional Driver Information Center DIC do the following 1 Turn the ignition to ON with the engine off 2 Fully press and release the accelerator pedal slowly three times within five seconds 3 Turn the key to OFF If the CHANGE ENGINE OIL message comes back on when you
116. at your own speed press the INFO button repeatedly A new group of words will appear on the display with each press Once the complete message has been displayed INFO will disappear from the display until another new message is received The old message can be displayed by pressing the INFO button You can view an old message until a new message is received or a different station is tuned to TRAF Traffic If TRAF appears on the display the tuned station broadcasts traffic announcements To receive the traffic announcement from the tuned station press this button Brackets will be displayed around TRAF and when a traffic announcement comes on the tuned radio station you will hear it If the current tuned station does not broadcast traffic announcements press the TRAF button and the radio will seek to a station that does When the radio finds a station that broadcasts traffic announcements the radio will stop and brackets will be displayed around TRAF When a traffic announcement comes on the tuned radio station you will hear it If no station is found NO TRAFFIC will appear on the display 3 80 If the brackets are on the display and TRAF is not you can then press the TRAF button to remove the brackets or use the TUNE knob or the SEEK arrows to go toa station that supports traffic announcements If no station is found NO TRAFFIC will appear on the display Your radio will play a traffic announcement if the volume is low Yo
117. atch plate and keep pulling until you can buckle the belt 1 27 Rear Seat Passengers Lap Shoulder Belt The positions next to the windows have lap shoulder belts Here s how to wear one properly It s very important for rear seat passengers to buckle up Accident statistics show that unbelted people in the rear seat are hurt more often in crashes than those who are wearing safety belts Rear passengers who aren t safety belted can be thrown out of the vehicle in a crash And they can strike others in the vehicle who are wearing safety belts Rear Seat Outside Passenger Positions 1 Pick up the latch plate and pull the belt across you Don t let it get twisted The shoulder belt may lock if you pull the belt across you very quickly If this happens let the belt go back slightly to unlock it Then pull the belt across you more slowly 2 Push the latch plate into the buckle until it clicks 1 28 If the belt stops before it reaches the buckle tilt the 3 To make the lap part tight pull down on the buckle latch plate and keep pulling until you can buckle it end of the belt as you pull up on the shoulder part Pull up on the latch plate to make sure it is secure If the belt is not long enough see Safety Bel on page 1 38 Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to 1 29 a X d N Y h
118. atch plate and pulling it along the belt Put the restraint on the seat Run the vehicle s safety belt through or around the restraint The child restraint instructions will show you how 1 57 5 To tighten the belt pull its free end while you push down on the child restraint If you re using a forward facing child restraint you may find it helpful to use your knee to push the child restraint as you tighten the belt 6 Push and pull the child restraint in different directions to be sure it is secure To remove the child restraint just unbuckle the vehicle s safety belt When you remove the child restraint be sure to reconnect the lap and shoulder parts of the belt so they will be ready to work for an adult or larger child passenger 4 Buckle the belt Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to 1 58 Securing a Child Restraint in the Right Front Seat Position If your child re nt is equipped with the LATCH em see Lowe F R horages and Top Tethers for Children LA ystem on page 1 on page 1 49 if the child restraint has one Your vehicle has a front passenger air bag Never put a rear facing child restraint in this seat Here is why A child in a rear facing child restraint can be seriously injured or killed if the front passenger s air bag inflates This is because the back of the rear facing child re
119. ate the automatic headlamp control when it is dark enough outside and turn off all the lamps and lights during the day except for the Daytime Running Lamps DRL PS Parking Lamps Turning the control to this position turns on the parking lamps together with the following Taillamps Instrument Panel Lights ZD Headlamps Turning the control to this position turns on the headlamps together with the previously listed lamps and lights Lamps on Reminder If the driver s door is opened and you turn the ignition to OFF while leaving the lamps on you will hear a warning chime Daytime Running Lamps DRL Daytime Running Lamps DRL can make it easier for others to see the front of your vehicle during the day DRL can be helpful in many different driving conditions but they can be especially helpful in the short periods after dawn and before sunset Fully functional daytime running lamps are required on all vehicles first sold in Canada A light sensor on top of the instrument panel makes the DRL work so be sure it is not covered The DRL system will make your reduced intensity high beam headlamps come on in daylight when The ignition is on The exterior lamps control is in AUTO The shift lever is not in PARK P When the DRL are on only your reduced intensity high beam headlamps will be on The taillamps and other lamps will not be on Your instrument panel will not be lit up When it is dark enough outsid
120. ational Highway Traffic Safety Administration which grades tires by treadwear traction and temperature performance This applies only to vehicles sold in the United States The grades are molded on the sidewalls of most passenger car tires The Uniform Tire Quality Grading system does not apply to deep tread winter type snow tires space saver or temporary use spare tires tires with nominal rim diameters of 10 to 12 inches 25 to 30 cm or to some limited production tires While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades they must also conform to federal safety requirements and additional General Motors Tire Performance Criteria TPC standards 5 72 Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course For example a tire graded 150 would wear one and a half 1 5 times as well on the government course as a tire graded 100 The relative performance of tires depends upon the actual conditions of their use however and may depart significantly from the norm due to variations in driving habits service practices and differences in road characteristics and climate Traction AA A B C The traction grades from highest to lowest are AA A B and C Those grades represent the tire s ability to stop on wet pavement as measured under controlled c
121. ave programmed on the radio preset pushbuttons If your vehicle has the MP3 CD player pressing this button will take you to the next folder PLAY Press this button to play a CD when listening to the radio MUTE Press this button to silence the system Press it again or any other radio button to turn on the sound A voL Y Volume Press the up or the down arrow to increase or to decrease volume Theft Deterrent Feature THEFTLOCK is designed to discourage theft of your radio The feature works automatically by learning a portion of the Vehicle Identification Number VIN If the radio is moved to a different vehicle it will not operate and LOCKED will be displayed With THEFTLOCK activated your radio will not operate if stolen Audio Steering Wheel Controls lf your vehicle has this feature you can control certain radio functions using the buttons on your steering wheel PRESET Press this button to go to a station you have programmed on the radio preset pushbuttons If your vehicle has the six disc CD audio system and multiple discs are loaded each press of PRESET will take you to the next disc If your vehicle has the MP3 CD player pressing this button will take you to the next folder BAND Press this button to choose FM1 FM2 AM or XM1 or XM2 48 contiguous US states if equipped Press this button when a CD is playing to listen to the radio The inactive CD will remain safely inside the radio fo
122. ay be blocking the signal Take a few steps to the left or right hold the transmitter higher and try again Check to determine if battery replacement is necessary See Battery Replacement under Remote Keyless Entry System Operator on page 2 4 If you are still having trouble see your dealer or a qualified technician for service Remote Keyless Entry System Operation With this feature you can lock and unlock your doors from about 3 feet 1 m up to 30 feet 9 m away using the remote keyless entry transmitter supplied with your vehicle UNLOCK Press UNLOCK to unlock only the driver s door If you press UNLOCK again within five seconds the passengers doors will unlock If you would like all the doors to unlock the first be you press UNLOCK and your vehicle is ipp he Driver Information Center DIC see DIC Vehicle on page 3 57 The UNLOCK button on the remote keyless entry transmitter will disarm the content theft deterrent system See Content Theft Deterrent on page 2 14 for more information If you would like to program the way the headlamps and parking lamps operate with remote unlock confirmation and your vehicle is equipped with the Driver Information Center DIC see DIC Vehicle Personalization on page 3 57 LOCK To lock all doors press LOCK The LOCK button on the remote keyless entry transmitter will arm the content theft deterrent system See Content Theft Deterrent o
123. ay require for your vehicle hand controls wheelchair scooter lifts etc This program can also provide you with free resource information such as area driver assessment centers and mobility equipment installers The offer is available for a limited period of time from the date of vehicle purchase lease For more details or to determine your vehicle s eligibility see your GM dealer or call the GM Mobility Assistance Center at 1 800 323 9935 Text telephone TTY users call 1 800 833 9935 GM of Canada also has a Mobility Program Call 1 800 GM DRIVE 463 7483 for details All TTY users call 1 800 263 3830 Roadside Assistance Program Security While You Travel 1 800 ROADSIDE 1 800 762 3743 As the proud owner of a new Pontiac vehicle you are automatically enrolled in the Pontiac Roadside Assistance program This value added service is intended to provide you with peace of mind as you drive in the city or travel the open road Pontiac s Roadside Assistance toll free number is staffed by a team of technically trained advisors who are available 24 hours a day 365 days a year We take anxiety out of uncertain situations by providing minor repair information over the phone or making arrangements to tow your vehicle to the nearest Pontiac dealer We will provide the following services for 3 years 36 000 miles 60 000 km at no expense to you Fuel delivery Lock out service identification required Tow t
124. belt 5 Push and pull the child restraint in different directions to be sure it is secure To remove the child restraint just unbuckle the vehicle s safety belt and let it go back all the way The safety belt will move freely again and be ready to work for an adult or larger child passenger 1 56 Securing a Child Restraint in a Center Rear Seat Position lf ASA child re tis equipped C ce Lowe F R horages ad Top Tethers for Children LA ystem on page 1 on page 1 49 if the child restraint has one lf your child restraint does not have the LATCH system you will be using the lap shoulder belt to secure the child restraint in the center rear seating position To secure a child restraint in this position you ll use only the lap part of the belt Disconnect the shoulder part of the belt and store it before securing child restraint See Center Rear Passenger Position on page 1 32 lf you re using a top strap equipped child restraint in the center rear seat and need to temporarily transport a flat tire for repair move the child restraint to a rear seat outboard position See Securing a Child Restraint in a Rear Outside Seat Position on page 1 54 for more on is including important safety information Be sure to follow the instructions that came with the child restraint Secure the child in the child restraint when and as the instructions say Make the belt as long as possible by tilting the l
125. ble all the way and then loosen it at least two times If the spare tire did lower to the ground continue with Step 9 under Removing the Spare Tire Vehicles without the Sliding Rear Convenience Tray earlier in this section If you still cannot lower the spare tire to the ground see Secondary Latch System following Secondary Latch System Your vehicle has an underbody mounted tire hoist assembly equipped with a secondary latch system It s designed to stop the compact spare tire from suddenly falling off your vehicle if the cable holding the spare tire is damaged For the secondary latch to work the must be stowed with the valve stem pointing down See Storing the Spare Tire and Tools later in this section for instructions on storing the compact spare tire correctly Before beginning this procedure read all the instructions Failure to read and follow the instructions could damage the hoist assembly and you and others could get hurt Read and follow the instructions listed below tire 5 85 Front Wheel Drive To release the spare tire from the secondary latch do the following Someone standing too close during the procedure could be injured by the jack If the spare tire does not slide off the jack completely make sure no one is behind you or on either side of you as you pull the jack out from the spare 1 Turn the wrench counterclockwise until If the cable is not visible
126. bol will appear on the display 2 Press PROG TYPE if it is not already on 3 Turn the SELECT knob to select a PTY 4 Press and hold one of the six numbered pushbuttons until you hear a beep Whenever you press that numbered pushbutton the PTY you set will return if program type select mode is activated 5 Repeat the steps for each pushbutton 3 69 RDS Messages ALERT Alert warns of national or local emergencies When an alert announcement comes on the current radio station ALERT will appear on the display You will hear the announcement even if the volume is muted or a CD is playing If a CD is playing play will stop during the announcement You will not be able to turn off alert announcements ALERT will not be affected by tests of the emergency broadcast system This feature is not supported by all RDS stations INFO Information If the current station has a message INFO will appear on the display Press this button to see the message The message may display the artist song title call in phone numbers etc If the whole message is not displayed parts of the message will appear every three seconds To scroll through the message at your own speed press the INFO button repeatedly A new group of words will appear on the display with each press Once the complete message has been displayed INFO will disappear from the display until another new message is received The old message can be displayed by press
127. brush later if you need to to get all the rust or dirt off Never use oil or grease on studs or nuts If you do the nuts might come loose Your wheel could fall off causing a serious accident 8 Install the spare tire and put the wheel nuts back on with the rounded end of the nuts toward the wheel Tighten each nut by hand until the wheel is held against the hub 9 Lower the vehicle by attaching the folding wheel wrench to the jack and turning the wrench counterclockwise Lower the jack completely 5 95 10 Tighten the wheel nuts firmly in a crisscross sequence as shown Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose and even come off This could lead to an accident Be sure to use the correct wheel nuts If you have to replace them be sure to get new GM original equipment wheel nuts Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to 100 lb ft 140 Nem 5 96 Notice Improperly tightened wheel nuts can lead to brake pulsation and rotor damage To avoid expensive brake repairs evenly tighten the wheel nuts in the proper sequence and to the proper torque specification 11 Don t try to put a wheel cover on the compact spare tire It won t fit Store the wheel cover securely in the rear of the vehicle until you have the flat tire repaired or replaced Notice Wheel covers will not fit on your compact spare If you tr
128. by some DVDs and to improve the audio quality d Sound This button moves to the next language or commentary Press this button to call up a menu that will operate only when a DVD is playing The format and content of this function will vary from disc to disc lt q Rewind Press this button to reverse the DVD To stop reversing press this button again This button may not work when the DVD is playing the copyright information or the previews 3 110 SRCE Source Press this button to toggle the system between the DVD player and an auxiliary source E Stop Press this button to stop playing rewinding or fast forwarding a DVD or CD Press this button twice to return to the beginning of the DVD el Prior Chapter Track Press this button to go to the beginning of the current chapter or track Press this button again to return to the previous chapter or track This button may not work when the DVD is playing the copyright information or previews 1 through 0 Numeric Keypad The numeric keypad provides you with the capability of direct chapter title and track number selection 10 Double Digit Entries Press this button located on the bottom right of the numeric key pad to select chapter title and track numbers greater than 9 Press this button before selecting the number amp Clear Press this button located on the bottom left of the numeric key pad within three seconds after inputting a numeric selectio
129. ce Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transaxle If you are stuck do not spin the tires When stopping on a hill use the brakes to hold the vehicle in place Shift Lock Release This vehicle is equipped with an electronic shift lock release system Shift lock release is designed to do the following e Prevent ignition key removal unless the shift lever is in PARK P with the shift lever button fully released Prevent movement of the shift lever out of PARK P unless the ignition is in a position other than OFF Shift lock release is always functional except in the case of a discharged or low voltage less than 9V battery Parking Brake The parking brake is located on the driver s side under the instrument panel To set the parking brake hold the regular brake pedal down with your right foot and push down on the parking brake pedal with your left foot If the ignition is on the brake system warning light will come on See Brake System Warning Light on page 3 36 To release the parking brake hold the regular brake pedal down with your right foot while you push down on the parking brake pedal with your left foot To release the tension on the parking brake cable you will need to apply about the same amount of pressure to the parking brake pedal as you did when you set the parking brake When you remove your foot from the parking brake p
130. ceeeceeeeeeeenees 6 7 Maintenance Schedule cont Maintenance Records 52 manerer 6 14 Maintenance Requirements W u dssseseeererreree 6 2 Normal Maintenance Replacement Parts 6 13 Owner Checks and Services eeeeeeee ees 6 8 Recommended Fluids and Lubricants 6 12 Scheduled Maintenance ceceeeeeeeeeeeeee ees 6 4 USING YOUN sierras a Sse Aan 6 3 Your Vehicle and the Environment 5 6 2 Maintenance When Trailer Towing 0 08 4 49 Making TUNS ceeste eniron erie 4 47 Malfunction Indicator Light 1 sssssseeeeererree 3 39 Manual Lumbar Controls eceeeeeeeeeeeeee eee es 1 3 Manual Passenger Seat cceeeeeeeeeeeeeeeeeeees 1 2 Matching Transmitter s to Your Vehicle 2 5 Message All Wheel Drive Disable Warning 3 49 GOMER site E EEN E 3 43 Change Engine Oil W u u u dc s senere teeter eens 3 46 Charging System Indicator eeeeeeeee ee 3 45 Door Ajar Warning eceeeeeeeeeeeeeeee eee hver 3 47 Engine Coolant Temperature Warning 3 44 Low Brake Fluid Warning ccce 3 50 Low Fuel Warning seeeeeeeeeeeeeeeeneeeee 3 50 Low Oil Pressure cceceeeeeeeee eee eeeeee een ees 3 45 LOW MiO cria e este EE E AE 3 47 Low Washer Fluid Warning e eeeeeeees 3 49 Park Lamp Warning ceeeeeeeeeeeee eee eees 3 52 PASS Ke
131. cle Use a vacuum cleaner often to get rid of dust and loose dirt Wipe vinyl leather plastic and painted surfaces with a clean damp cloth Cleaning Fabric Carpet Your dealer has cleaners for the cleaning of fabric and carpet They will clean normal spots and stains very well You can get_GM approved cleaning products from your dealer See Vehicle Care Appearance Materials on page 5 110 5 103 Here are some cleaning tips Always read the instructions on the cleaner label Clean up stains as soon as you can before they set Carefully scrape off any excess stain e Use a clean cloth or sponge and change to a clean area often A soft brush may be used if stains are stubborn Ifa ring forms on fabric after spot cleaning clean the entire area immediately or it will set Using Cleaner on Fabric 1 Vacuum and brush the area to remove any loose dirt 2 Always clean a whole trim panel or section Mask surrounding trim along stitch or welt lines 3 Follow the directions on the container label 4 Apply cleaner with a clean sponge Do not saturate the material and do not rub it roughly 5 As soon as you have cleaned the section use a sponge to remove any excess cleaner 6 Wipe cleaned area with a clean water dampened towel or cloth 7 Wipe with a clean cloth and let dry 5 104 Special Fabric Cleaning Problems Stains caused by such things as catsup coffee black egg fruit fruit j
132. coast to coast Just as with FM tall buildings or hills can interfere with satellite radio signals causing the sound to come and go Your radio may display NO SIGNAL to indicate interference Care of Your CDs and DVDs Handle discs carefully Store them in their original cases or other protective cases and away from direct sunlight and dust If the surface of a disc is soiled dampen a Clean soft cloth in a mild neutral detergent solution and clean it wiping from the center to the edge Be sure never to touch the side without writing when handling discs Pick up discs by grasping the outer edges or the edge of the hole and the outer edge Care of Your CD and DVD Player The use of CD lens cleaner discs is not advised due to the risk of contaminating the lens of the CD optics with lubricants internal to the CD mechanism Cleaning Your DVD Player When cleaning the outside DVD cabinet face and buttons use only a clean cloth dampened with clean water Cleaning the Video Screen When cleaning the video screen use only a clean cloth dampened with clean water Use care when directly touching or cleaning the screen as damage may result Integrated Windshield Antenna The antenna in your vehicle is a very thin metal layer in the windshield If you look near the edges of the windshield you can see the outline of the antenna The connector is at the top of the windshield where the headliner ends If you experience diffic
133. content theft deterrent system is armed the liftgate tailgate may be opened by using one of the following methods From the outside insert the key into the lock and turn it clockwise Press REAR on the remote keyless entry transmitter Arming with the Power Lock Switch Your alarm system will arm when you use either power door lock switch to lock the doors while any door or the liftgate tailgate is open and the key is removed from the ignition The security light will start flashing to let you know the system is armed Within five seconds after the security light begins to flash any door can be manually unlocked and opened without sounding the alarm A door unlocked manually will remain unlocked until locked again Arming with the Remote Keyless Entry Transmitter Your alarm system will arm when you press LOCK once on your remote keyless entry transmitter to lock the doors The security light will come on for 30 seconds and then start flashing to let you know the system is armed Within the 30 second delay after the security light comes on and an additional five seconds after the light begins to flash any door can be manually unlocked and opened without sounding the alarm If LOCK is pressed on your remote keyless entry transmitter twice within five seconds any door can be manually unlocked and opened within five seconds after the security light begins to flash without sounding the alarm A door unlocked manually
134. control To use the headphones turn the switch to ON An indicator light on the headphones will illuminate If the light does not illuminate the batteries may need to be replaced See Battery Replacement later in this section for more information Switch the headphones to OFF when not in use The transmitters are located below the overhead RSE control panel The headphones will shut off automatically to save the battery power if the DVD system is shut off or if the headphones are out of range of the transmitters for more than three minutes If you move too far forward or step out of the vehicle the headphones will lose the audio signal To adjust the volume on the cordless headphones use the volume control Notice Do not store the headphones in heat or direct sunlight This could damage the headphones and repairs would not be covered by your warranty Keep the headphones stored in a cool dry place If there is a decreased audio signal during CD or DVD play you may hear a low hissing noise through the speakers and or headphones If the hissing sound in the wireless headphones seems excessive make sure that the headphone batteries are fully charged Some amount of hissing is normal 3 103 Battery Replacement To change the batteries do the following 1 Loosen the screw on the battery compartment door located on the left side of the headphone earpiece 2 Replace the two AAA batteries in the compartment Make su
135. cord or heart This means that when anyone who has been drinking driver or passenger is in a crash that person s chance of being killed or permanently disabled is higher than if the person had not been drinking Drinking and then driving is very dangerous Your reflexes perceptions attentiveness and judgment can be affected by even a small amount of alcohol You can have a serious or even fatal collision if you drive after drinking Please do not drink and drive or ride with a driver who has been drinking Ride home in a cab or if you are with a group designate a driver who will not drink Control of a Vehicle You have three systems that make your vehicle go where you want it to go They are the brakes the steering and the accelerator All three systems have to do their work at the places where the tires meet the road Sometimes as when you are driving on snow or ice it is easy to ask more of those control systems than the tires and road can provide That means vou can lose control of your vehicle Also see Traction Contro System TCS tem TCS on page 4 10 Braking Braking action involves perception time and reaction time First you have to decide to push on the brake pedal That is perception time Then you have to bring up your foot and do it That is reaction time Average reaction time is about 3 4 of a second But that is only an average It might be less with one driver and as lon
136. crash That could cause injury to the person sitting there Always press rearward on the seatback to be sure it is locked To recline the seatbacks lift up on the recliner lever located on the outboard side of the seatback Move the seatback to the desired position It is easier to raise or lower the seatback if you lean forward and take the weight off the seatback To fold the seatback forward lift up on the recliner lever and fold the seatback forward The seatback will lock into place Lift up on the lever again to raise the seatback The seatback will lock into place when you push it back to the upright position After raising a seatback to an upright position push and pull on the seatback to check that it is locked upright Removing the Split Bench Seat Each section of the split bench seat can be flipped forward or removed individually 1 Unlatch the shoulder belt from the lap belt 2 Make sure the seatback is in the upright position 3 Lift the seatback recliner lever to fold the seatback forward a EPEE E ee E T 4 Pull the lever located at the base on the outboard 5 To release the front latches squeeze the angled side of the seat to release the rear latches from the latch release bar toward the straight crossbar floor pins and flip ine Seal forward l 6 Remove the seat by rocking it slightly toward the The seat can stay in this position or it can be rear of the vehicle and then pulling it o
137. culty in loading and ejecting If these problems occur try a known good CD Do not add paper labels to CDs they could get caught in the CD player Do not play 3 inch CDs without a standard adapter CD If an error appears on the display see CD Messages later in this section bb 1 Forward Press and hold this pushbutton to advance quickly within a track You will hear sound at a reduced volume Release the pushbutton to play the passage The display will show the elapsed time of the track RDM 2 Random Press this pushbutton to hear the tracks in random rather than sequential order RDM and the track number will appear on the display Press RDM again to turn off random play 3 Next Folder This button does not have a function for non MP3 CDs 4 lt lt Reverse Press and hold this pushbutton to reverse quickly within a track You will hear sound at a reduced volume Release the pushbutton to play the passage The display will show the elapsed time of the track 6 Previous Folder This button does not have a function for non MP3 CDs 3 83 EQ Equalizer Press EQ to select the desired customized equalization setting while playing a CD The equalization will be automatically set whenever you play a CD See EQ listed previously for more information A SEEK V Press the up arrow to go to the start of the next track Press the down arrow to go to the start of the previous track Pressing eith
138. cures the cover in place B Sliding Rear F Storage Convenience Tray Compartment C Wing Nut Cap Hole D J hook 5 100 Push the sliding rear tray forward to the stored position Open the driver s side storage compartment door of the sliding rear tray Remove the rear cap on the bottom of the storage compartment and flip the D ring up Lay the tire on top of the driver s side storage compartment with the valve stem down Make sure you can see the D ring through the center hole of the tire Remove the J hook and the wing nut from the back of the jack access door Assemble the wing nut and the J hook Install the wing nut and the J hook to the D ring through the center hole of the tire 10 Tighten the wing nut to secure the tire to the floor Push and pull on the tire to make sure the tire is secure and does not move Put back all tools as they were stored in the storage compartment Attach the wrench back to the jack Put the jack base on the bracket tab and sit the jack properly between the two ears of the bracket Use the bolt to tighten the jack Put the compartment cover back on slip the tabs on the bottom of the cover into the bottom of the cover opening Push the cover in place and push down the tab on the top of the cover so that it rests in the groove This secures the cover in place 5 101 Compact Spare Tire Although the compact spare tire was fully inflated when your vehicle wa
139. d then goes back into the right lane again A simple maneuver Not necessarily Passing another vehicle on a two lane highway is a potentially dangerous move since the passing vehicle occupies the same lane as oncoming traffic for several seconds A miscalculation an error in judgment or a brief surrender to frustration or anger can suddenly put the passing driver face to face with the worst of all traffic accidents the head on collision So here are some tips for passing Drive ahead Look down the road to the sides and to crossroads for situations that might affect your passing patterns If you have any doubt whatsoever about making a successful pass wait for a better time Watch for traffic signs pavement markings and lines If you can see a sign up ahead that might indicate a turn or an intersection delay your pass A broken center line usually indicates it is all right to pass providing the road ahead is clear Never cross a solid line on your side of the lane or a double solid line even if the road seems empty of approaching traffic Do not get too close to the vehicle you want to pass while you are awaiting an opportunity For one thing following too closely reduces your area of vision especially if you are following a larger vehicle Also you will not have adequate space if the vehicle ahead suddenly slows or stops Keep back a reasonable distance When it looks like a chance to pass is coming up st
140. d checking and adjusting the pressure in all four tires If you reset the system when the tire pressures are incorrect the check tire pressure system will not work properly and may not alert you when a tire is low or high 5 67 To reset the system do the following 1 With the engine off turn the ignition to ON 2 Press the MODE button until the DIC reads TIRE PRESSURE LOW CHECK TIRES 3 Press and hold the SET button until TIRE PRESSURE NORMAL is displayed You will hear three chimes and the LOW TIRE PRESSURE message will go off and the DIC will return to TIRE PRESSURE NORMAL If the LOW TIRE PRESSURE message comes back on the check tire pressure system has not reset Repeat the procedure The system completes the calibration process during driving The system learns the pressure at each tire throughout the operating speed range of your vehicle The system normally takes between 30 and 60 minutes of driving to learn the tire pressures The system normally takes 10 to 20 minutes of driving in each speed range to learn tire pressures The speed ranges are 20 to 40 mph 32 to 64 km h 40 to 60 mph 64 to 96 km h and above 60 mph 96 km h This time may be longer depending on your individual driving habits The learning process does not need to be completed during a single trip Once learned the system will remember the tire pressures until the system is reset 5 68 Tire Inspection and Rotation Tires should be r
141. d know how and the proper tools and equipment for the job If you have any doubt see your GM Goodwrench dealer to have a qualified technician do the work Some maintenance services can be complex So unless you are technically qualified and have the necessary equipment you should have your GM Goodwrench dealer do these jobs When you go to your GM Goodwrench dealer for your service needs you will know that GM trained and supported service technicians will perform the work using genuine GM parts If you want to get service information see Publications Ordering Information on page 7 13 Por ee ena page 6 8 tells you what should be checked when to check it and what you can easily do to help keep your vehicle in good condition The proper repla use are listed in emen fluids and lubrican ETE Fluids and ea on page 6 12 and Normal Maintenance Replacement Parison page 6 13 When your vehicle is serviced make sure these are used All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle We recommend the use of genuine GM parts Scheduled Maintenance When the CHANGE ENGINE OIL message comes on it means that service is required for your vehicle Have your vehicle serviced as soon as possible within the next 600 miles 1 000 km It is possible that if you are driving under the best conditions the engine oil life system may not indicate that vehicle service i
142. d on child restraints have used the adult belt system in the vehicle To help reduce the chance of injury the child also has to be secured within the restraint The vehicle s belt system secures the add on child restraint in the vehicle and the add on child restraints harness system holds the child in place within the restraint One system the three point harness has straps that come down over each of the infant s shoulders and buckle together at the crotch The five point harness system has two shoulder straps two hip straps anda crotch strap A shield may take the place of hip straps A T shaped shield has shoulder straps that are attached to a flat pad which rests low against the child s body A shelf or armrest type shield has straps that are attached to a wide shelf like shield that swings up or to the side When choosing a child restraint be sure the child restraint is designed to be used in a vehicle If it is it will have a label saying that it meets federal motor vehicle safety standards Then follow the instructions for the restraint You may find these instructions on the restraint itself or in a booklet or both These restraints use the belt system in your vehicle but the child also has to be secured within the restraint to help reduce the chance of personal injury When securing an add on child restraint refer to the instructions that come with the restraint which may be on the restraint itself or in a bookle
143. d pushbutton that corresponds to the CD you want to play A small bar will appear under the CD number that is playing and the track number will appear If an error appears on the display see CD Messages later in this section LOAD CD amp Eject Press the CD eject side of this button to eject a CD You will hear a beep and the light will flash to let you know when a CD is being ejected REMOVE CD will be displayed You can now remove the CD If the CD is not removed after 25 seconds the CD will be automatically pulled back into the receiver If you try to push the CD back into the receiver before the 25 second time period is complete the receiver will sense an error and will try to eject the CD several times before stopping Do not repeatedly press the CD eject button to eject a CD after you have tried to push it in manually The receivers 25 second eject timer will reset at each press of eject which will cause the receiver to not eject the CD until the 25 second time period has elapsed Once the player stops and the CD is ejected remove the CD After removing the CD push the PWR knob off and then on again or wait for the system to reset This will clear the CD sensing feature and enable CDs to be loaded into the player again lt REV Reverse Press and hold this button to reverse quickly within a track You will hear sound at a reduced volume Release the button to play the passage The display will show the
144. ded with the following fixed bit rates 32 kbps 40 kpbs 56 kpbs 64 kpbs 80 kpbs 96 kpbs 112 kpbs 128 kpbs 160 kpbs 192 kpbs 224 kpbs 256 kpbs and 320 kpbs or a variable bit rate Song title artist name and album will be available when recorded using ID3 tags versions 1 and 2 The player will be able to read and play a maximum of 50 folders 50 playlists 10 sessions and 255 files Long file folder or playlist names or a combination of a large number of files and folders or playlists may cause the player to be unable to play up to the maximum number of files folders playlists or sessions If you wish to play large numbers of files folders playlists or sessions minimize the length of the file folder or playlist name You can also play an MP3 CD that was recorded using no file folders The system can support up to 11 folders in depth though keep the depth of the folders to a minimum in order to keep down the complexity and confusion in trying to locate a particular folder during playback If a CD contains more than the maximum of 50 folders 50 playlists 10 sessions and 255 files the player will let you access and navigate up to the maximum but all items over the maximum will be ignored Root Directory The root directory will be treated as a folder If the root directory has compressed audio files the directory will be displayed as F1 ROOT All files contained directly under the root directory will be accessed
145. desired When you are listening to a CD the last selected RDS station will interrupt play if that selected program type format is broadcast SCAN You can scan the stations within a PTY by performing the following 1 Press the P TYPE button to activate program type select mode P TYPE and the last selected PTY will appear on the display 2 Turn the P TYPE knob to select a PTY 3 Once the desired PTY is displayed press and hold either SCAN arrow and the radio will begin scanning the stations in the PTY 4 Press either SCAN arrow to stop at a station If both PTY and TRAF are on the radio will scan for stations with the selected PTY and traffic announcements BAND Alternate Frequency Alternate frequency allows the radio to switch to a stronger station with the same program type To turn alternate frequency on press and hold BAND for two seconds AF ON will appear on the display The radio may switch to stronger stations To turn alternate frequency off press and hold BAND again for two seconds AF OFF will appear on the display The radio will not switch to other stations When you turn the ignition off and then on again the alternate frequency feature will automatically be turned on This function does not apply for XM Satellite Radio Service 3 93 Setting Preset PTYs RDS Only The six numbered pushbuttons let you return to your favorite PTYs These buttons have factory PTY presets You can set up to 12 PT
146. dio system is equipped with a Radio Data System RDS RDS features are available for use only on FM stations that broadcast RDS information With RDS your radio can do the following Seek to stations broadcasting the selected type of programming e Receive announcements concerning local and national emergencies Display messages from radio stations Seek to stations with traffic announcements This system relies upon receiving specific information from these stations and will only work when the information is available In rare cases a radio station may broadcast incorrect information that will cause the radio features to work improperly If this happens contact the radio station While you are tuned to an RDS station the station name or the call letters will appear on the display instead of the frequency RDS stations may also provide the time of day a program type PTY for current programming and the name of the program being broadcast XM Satellite Radio Service 48 Contiguous US States XM is a continental U S based satellite radio service that offers 100 coast to coast channels including music news sports talk and children s programming XM provides digital quality audio and text information including song title and artist name A service fee is required in order to receive the XM service For more information contact XM at www xmradio com or call 1 800 852 XMXM 9696 3 65 Playing
147. djust its position as desired When the video screen is not in use push it up into its stowed and latched position The DVD player and display will continue to operate when the video screen is in either the up or down positions The video screen contains the transmitters for the cordless headphones and the receiver for the remote control If the screen is in the closed position the signals will not be available for the operation of the headphones or the remote control Notice Avoid directly touching the video screen as damage may occur See Cleaning the Video on page 3 119 for more information 3 105 DVD Player The DVD player is located in the overhead console The DVD player can be controlled by the buttons on the DVD player and or by the buttons on the remote control See Remote Control later in this section for more information The DVD player is only compatible with DVDs of the appropriate region code for the country that the vehicle was sold in On some DVD jackets you will see the region displayed Standard audio CDs can also be played by the DVD player The video screen will default to off when an audio CD is played If an error message appears on the video screen see DVD Messages later in this section 3 106 DVD Player Buttons a Eject Press this button to eject a DVD or CD SRCE Source Press this button to toggle the system between the DVD playe
148. e like other modern motor vehicles has a number of sophisticated computer systems that monitor and control several aspects of the vehicle s performance Your vehicle uses on board vehicle computers to monitor emission control components to optimize fuel economy to Monitor conditions for airbag deployment and if so equipped to provide anti lock braking and to help the driver control the vehicle in difficult driving situations Some information may be stored during regular operations to facilitate repair of detected malfunctions other information is stored only in a crash or near crash event by computer systems commonly called event data recorders EDR In a crash or near crash event computer systems such as the Airbag Sensing and Diagnostic Module SDM in your vehicle may record information about the condition of the vehicle and how it was operated such as engine speed brake applications throttle position vehicle speed seat belt usage airbag readiness airbag performance data and the severity of a collision This information has been used to improve vehicle crash performance and may be used to improve crash performance of future vehicles and driving safety Unlike the data recorders on many airplanes these on board systems do not record sounds such as conversation of vehicle occupants To read this information special equipment is needed and access to the vehicle or the SDM is required GM will not access information abou
149. e the exterior lamps will come on automatically When it is bright enough outside the exterior lamps will go out and the DRL will turn on Of course you may still turn on the headlamps any time you need to As with any vehicle you should turn on the regular headlamp system when you need it Automatic Headlamp System When the exterior lamp control is turned to AUTO the headlamps and parking lamps will come on automatically when it is dark enough outside The lamps will come on automatically if the following conditions are met e It is dark enough outside The ignition is in ON The parking brake is released The exterior lamp control is in the AUTO position Fog Lamps The fog lamp button is located on the exterior lamp control Push the FOG PUSH button to turn the fog lamps on The FOG light indicates the fog lamps are on To turn off the fog lamps press the fog lamp button or turn the ignition off If you turn on the fog lamps while the DRL are on the parking lamps will turn on automatically Your fog lamps will go off while you switch to high beams Using your high beams in fog is not recommended Interior Lamps Your interior lamp control is located below the exterior lamp control Instrument Panel Brightness This feature controls the brightness of the instrument panel lights The knob for this feature is located on the interior lamps control Press the knob to extend it Turn the knob to ad
150. e Power Mirrors The power outside rearview mirror knob is located on the driver s door Turn the knob counterclockwise to adjust the driver s side mirror Turn the knob clockwise to adjust the passenger s side mirror After selecting which mirror to adjust move the knob in the direction you want the mirror to go If you are not adjusting either mirror leave the control in the center off position This prevents moving the mirrors accidentally once you have adjusted them Adjust each mirror so you can see the side of your vehicle and the area behind your vehicle Outside Convex Mirror Your passenger s side mirror is convex A convex mirrors surface is curved so you can see more from the driver s seat A convex mirror can make things like other vehicles look farther away than they really are If you cut too sharply into the right lane you could hit a vehicle on your right Check your inside mirror or glance over your shoulder before changing lanes 2 31 OnStar System OnStar uses global positioning system GPS satellite technology wireless communications and call centers to provide you with a wide range of safety security information and convenience services A complete OnStar user s guide and the terms and conditions of the OnStar Subscription Service Agreement are included in your vehicle s glove box literature For more information visit www onstar com contact OnStar at 1 88
151. e SET button at the end of the lever and release it 4 Take your foot off the accelerator pedal Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake This of course shuts off the cruise control But you do not need to reset it Once you are going about 25 mph 40 km h or more you can move the cruise control switch from ON to resume accelerate R A briefly You will go right back up to your chosen speed and stay there If you hold the switch at R A the vehicle will keep going faster until you release the switch or apply the brake So unless you want to go faster do not hold the switch at R A Increasing Speed While Using Cruise Control There are two ways to go to a higher speed Use the accelerator pedal to get to the higher speed Press the SET button at the end of the lever then release the button and the accelerator pedal You will now cruise at the higher speed Move the cruise switch from ON to R A Hold it there until you get up to the speed you want and then release the switch To increase your speed in very small amounts move the switch to R A briefly and then release it Each time you do this your vehicle will go about 1 mph 1 6 km h faster The accelerate feature will work whether or not you have set an initial cruise control speed Reducing Speed While Using Cruise Control There are two ways to reduce speed while using cruise control Pr
152. e of the liftgate tailgate opening The label on the net should be in the upper left corner Attach the middle hooks to the metal rings on the floor The convenience net has a maximum capacity of 100 Ibs 45 kg It is not designed to hold larger heavier loads Store such loads on the floor of your vehicle as far forward as you can When not in use it is recommended that you take down the rear convenience net to extend its life and retain its elasticity and to keep the rear exit clear Store the net in one of the storage compartments 2 41 Cargo Cover If your vehicle has a cargo cover you can use it to cover items in the rear of the vehicle Remove the cover from its pouch and place the loops found on each corner of the cover over the four pegs in each corner of the rear if the vehicle When it is not in use fold up the cover and return it to the pouch Cargo Net System Your vehicle may have a cargo net system designed to help keep larger loads from falling over The cargo net system consists of two side convenience nets one front convenience net and one rear convenience net The front and rear convenience nets have labels for proper placement when installing Attach the upper and lower hooks on both sides of the rear of the vehicle The label on the front and rear nets should be in the upper left corner and the labels should face rearward 2 42 The two side nets can go on either side of the vehicle Do o
153. e of the tailgate on each side of the vehicle for later attachment to the tray Push and pull on the floor track assembly to make sure it is locked into place Replacing the Sliding Rear Convenience Tray The floor track assembly must be installed first for the sliding rear convenience tray to stay locked into place See Replacing the Floor Track Assembly listed previously for more information 1 2 Pick up the tray by the handle and support the tray from the bottom with your other hand Place the tray onto the floor track assembly Make sure that the two front axles are placed over the hooks on the rear of the floor track assembly There are four axles on the bottom of the tray two in front and two in back Make sure the rollers on the bottom of the tray are located in the tracks of the floor track assembly Roll the tray forward into the vehicle until you hear a Click Press the release lever and pull the tray onto the tailgate Connect the hook to the tethered ring located on each side of the sliding rear convenience tray Push the release lever and roll the tray back into the vehicle You will hear a click when the tray is locked into position 2 47 Sunroof lf your vehicle has a sunroof the switch is located between the sun visors The sunroof switch will only work when the ignition is on or when the ignition is off and retained accessory power is active See Retained Acc
154. e placard Seel nflation Tire see on page 5 66 and Loading Your Vehicle on page 4 36 Radial Ply tire A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread Rim A metal support for a tire and upon which the tire beads are seated Sidewall The portion of a tire between the tread and the bead Speed Rating An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate Traction The friction between the tire and the road surface The amount of grip provided Tread The portion of a tire that comes into contact with the road Treadwear Indicators Narrow bands sometimes called wear bars that show across the tread of a tire when only 2 32 inch of tread remains See Is Time for New Tires on page 5 70 UTQGS Uniform Tire Quality Grading Standards a tire information system that provides consumers with ratings for a tire s traction temperature and treadwear Ratings are determined by tire manufacturers using government testing procedures The ratings are molded into the sidewall of the tire See Uniform Tire Qualit on page 5 72 Vehicle Capacity Weight The number of designated seating positions multiplied_by 150 lbs 68 kg plus the rated cargo load SATER on page 4 36 Vehicle Maximum Load on the Tire Load on an individual tire due to curb weight accessory weight occupant weight and cargo weigh
155. e service See footnote h Change automatic ta fluid and filter normal service Replace spark plugs and inspect spark plug wires An Emission Control Service Engine cooling system service or every 5 years whichever occurs first An Emission Control Service See footnote i Maintenance Footnotes t The U S Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle s useful life We however urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded a Visually inspect brake lines and hoses for proper hook up binding leaks cracks chafing etc Inspect disc brake pads for wear and rotors for surface condition Inspect other brake parts including calipers parking brake etc Check parking brake adjustment b Visually inspect front and rear suspension and steering system for damaged loose or missing part or signs of wear Inspect power steering lines and hoses for proper hook up binding leaks cracks chafing etc c Visually inspect hoses and have them replaced if they are cracked swollen or deteriorated Inspect all pipes fittings and clamps replace with genuine GM parts as needed To help ensure proper operation a pressure test of the cooling system and pre
156. e worn low and snug on the hips just touching the thighs In a crash this applies force to the strong pelvic bones And you would be less likely to slide under the lap belt If you slid under it the belt would apply force at your abdomen This could cause serious or even fatal injuries The shoulder belt should go over the shoulder and across the chest These parts of the body are best able to take belt restraining forces The safety belt locks if there is a sudden stop or crash or if you pull the belt very quickly out of the retractor 1 19 Shoulder Belt Height Adjuster To move it down push down on the button and move the height adjuster to the desired position Before you begin to drive move the shoulder belt adjuster to the height that is right for you You can move the adjuster up just by pushing up on the shoulder belt guide After you move the adjuster to where you want it try to move it down without pushing the button down to make sure it has locked into position Adjust the height so that the shoulder portion of the belt is centered on your shoulder The belt should be away from your face and neck but not falling off your shoulder a NREN 1 20 Q What s wrong with this A The shoulder belt is too loose It will not give nearly as much protection this way You can be seriously hurt if your shoulder belt is too loose In a crash you would move forward too much which could
157. ea RE GE SENER STERSLER 5 53 Halogen Bulbs EN seddel 5 50 Bulb Replacement cont Headlamps sr rar eres a 5 51 Replacement Bulbs cs eeeeeeeeeeeeeeeees 5 55 Taillamps Stoplamps and Back Up Lamps 5 54 Buying New TIOS 5228 ub hen br oase n r 5 71 California Fuel arcmin ordner kede 5 5 Canada Customer Assistance sssseeeereee 7 5 Canadian Owners siisi angste eee eee eee eee een eeneeaees ii Canadian Roadside Assistance 6 eeeeeeeeees 7 7 Canceling the Rear Door Security Locks 2 10 Capacities and Specifications cceeeee 5 118 Carbon Monoxide ccceseeee sees 4 28 2 10 2 29 Care of Safety Bels icc cacestidatiecteutedasidedeacetessedaagneas 5 106 Your CD and DVD Player salsa 3 118 Your CDs and DVDS cceceeeeeeenee renerne 3 118 Cargo COVER issiusti a eani ea e 2 42 Cargo Lampris nesan ainin n a E E tice 3 19 Cargo Net System W W W sssseeeerere renere renerne 2 42 Carrier Assembly Differential Rear Drive Module 2 5 49 CD Messages eeeeeeeeeeeeeees 3 74 3 89 3 102 Center Rear Passenger Position Safety Belts 1 32 CAINS WES ss ccscnanccetonarsteactdaatiaatnmntarecachenasda 5 75 Change Engine Oil Message seeeeeeee ee 3 46 Charging System Indicator Message 4 3 45 Check Engine Light 2 cceecttacsstaciunaunenctantcedectaenct aes 3 39 Tire Pressure System ccceeeeeeeeeeee
158. ecifications but emission control system performance may be affected The malfunction indicator lamp may turn on see on page 3 39 and your vehicle may fail a smog check test If this occurs return to your authorized GM dealer for diagnosis If it is determined that the condition is caused by the type of fuel used repairs may not be covered by your warranty Additives To provide cleaner air all gasolines in the United States are now required to contain additives that will help prevent engine and fuel system deposits from forming allowing your emission control system to work properly You should not have to add anything to your fuel However some gasolines contain only the minimum amount of additive required to meet U S Environmental Protection Agency regulations General Motors recommends that you buy gasolines that are advertised to help keep fuel injectors and intake valves clean If your vehicle experiences problems due to dirty injectors or valves try a different brand of gasoline Gasolines containing oxygenates such as ethers and ethanol and reformulated gasolines may be available in your area to contribute to clean air General Motors recommends that you use these gasolines particularly if they comply with the specifications described earlier Notice Your vehicle was not designed for fuel that contains methanol Do not use fuel containing methanol It can corrode metal parts in your fuel system and also damage the p
159. ecome so hot that it catches fire You or others could be burned Check your oil as soon as possible and have your vehicle serviced Notice Lack of proper engine oil maintenance may damage the engine The repairs would not be covered by your warranty Always follow the maintenance schedule in this manual for changing engine oil 3 46 Change Engine Oil Message CHANGE ENGINE OIL United States Canada If this message comes on and stays on after you started the engine have the oil changed For additional information on when to change the oil and resetting the system see Engine Oillon page 5 13 Low Tire Message LOW TIRE Dee PRESSURE United States Canada Your vehicle may have a LOW TIRE PRESSURE message If it does the check tire pressure system can alert you to a large change in the pressure of one tire After the system has been properly calibrated the LOW TIRE PRESSURE message will come on and a chime will sound if a pressure difference or low pressure is detected in one tire The message will stay on until you turr_off the ignition or reset or calibrate the system See Check Tire Pressure System on page 5 67 If the anti lock brake system warning light comes on the check tire pressure system may not be working properly See your dealer for service Also see Anti Lock Brake System Warning Light on page 3 37 Door Ajar Warning Message DOOR AJAR D 4 United States Canada This m
160. ect balance or fade and push and hold the AUDIO knob The radio will beep once and will adjust the display level to the middle position To adjust all tone and speaker controls to the middle position push and hold the AUDIO knob when no tone or speaker controls are displayed The radio will produce one beep and CENTERED will appear on the display Finding a Program Type PTY Station RDS and XM To select and find a desired PTY perform the following 1 Press the P TYPE button to activate program type select mode P TYPE and the last selected PTY will appear on the display 2 Turn the P TYPE knob to select a PTY 3 Once the desired PTY is displayed press either SEEK arrow to select the PTY and take you to the PTY s first station 4 If you want to go to another station within that PTY and the PTY is displayed press either SEEK arrow once If the PTY is not displayed press either SEEK arrow twice to display the PTY and then to go to another station 5 Press P TYPE to exit program type select mode If PTY times out and is no longer on the display go back to Step 1 If both P TYPE and TRAF are on the radio will search for stations with the selected PTY and traffic announcements To use the PTY interrupt feature press and hold the P TYPE button until you hear a beep on the PTY you want to interrupt with When selected an asterisk will appear beside that PTY on the display You may select multiple interrupts if
161. ed on the rearview mirror To turn either reading lamp on or off press the button located next to each lamp These lamps will come on each time you open the doors if the interior lamp control is in the ON or DOOR position Cargo Lamp The cargo lamp is located in the rear of the vehicle above the liftgate tailgate opening It comes on automatically each time you open the doors if the interior lamp control is in the DOOR position Battery Run Down Protection Your vehicle has a feature to help prevent you from draining the battery in case you accidentally leave the interior or exterior lamps on If you leave any interior or exterior lamps on while the ignition is in OFF they will automatically turn off after 10 minutes If your vehicle has less than 14 miles 24 km on the odometer the battery saver will turn off the lamps after only three minutes Instrument Panel Switchbank FELEO There is an instrument panel switchbank located below the comfort controls It contains switches or blanks that will vary with the options that are on your vehicle and a cigarette lighter accessory power outlet You may have the following switches Liftgate tailgate Release See Liftgate Tailgate on page 2 10 e Traction Disable See Traction Control Syste TCS on page 4 10 e Heated Seats See Heated Seats on page 1 3 If your vehicle has only two switches there will be a storage bin 3 19 Head Up Display HUD
162. edal it will pop up to the released position Notice Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts Verify that the parking brake is fully released and the brake warning light is off before driving If you_are towing a trailer and are parking on any hill see Towing a Trailerjon page 4 42 That section shows what to do first to keep the trailer from moving 2 25 Shifting Into Park P 1 Hold the brake pedal down with your right foot and set the parking brake with your left foot It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK P with the parking brake firmly set Your vehicle can roll If you have left the engine running the vehicle can move suddenly You or others could be injured To be sure your vehicle will not move even when you are on fairly level ground use the steps that follow If vou are 2 Move the shift lever into PARK P To do so hold pulling a trailer see Towing a Trailer on in the button on the lever then push the lever all page 4 42 the way toward the front of the vehicle 3 Turn the ignition key to OFF 4 Remove the key and take it with you If you can leave your vehicle with the key your vehicle is in PARK P 2 26 Leaving Your Vehicle With the Engine Running It can be dangerous to leave your vehicle with the engine running Your vehicle could move suddenly if the shift lev
163. ee eee es 5 67 Checking Coolant cceeeeeeeeeeeeeeeeeeeeeeeeees 5 24 Checking Engine Oil cceeeeeeeeeeeee teeter eens 5 13 Checking Things Under the Hood 0 08 5 10 Checking Your Restraint Systems e 1 71 Chemical Paint Spotting cceeeeeeeeeeeee eee 5 109 Child Restraints Child Restraint Systems ceeeeeeeeeee eee 1 45 Infants and Young Children a se 1 41 Lower Anchorages and Top Tethers for Children LATCH System eeeeeeeeeeeee 1 52 Older Children 0cccceceeeeeeeeeeeeeeeeeeeees 1 39 Securing a Child Restraint Designed for the LATCH System aseene 1 54 Securing a Child Restraint in a Center Rear Seat Position eee 1 56 Securing a Child Restraint in a Rear Outside Seat Position 0 1 54 Securing a Child Restraint in the Right Front Seat Position 1 59 TOP SAD wick rener dennin aE AE EAEE 1 49 Top Strap Anchor Location 0 eee 1 50 Where to Put the Restraint c eee 1 48 Cigarette Lighter cceeeeeeeeeeeeeeeeeeeeeee eens 3 23 Cleaning Inside of Your Vehicle eeeeeeeeeee ees 5 103 Outside of Your Vehicle ceeeeeeeeee ees 5 106 Cleaning cont Underbody Maintenance asasen 5 109 Video SCreGN snyde ved nade ees nen 3 119 Weatherstrip c0csescdaeceeaceetaecsdangecgeendanenne sine 5 106 Your DVD Player 522 aa he hor ub
164. eee 2 33 Operation 3 rune rare 3 24 3 27 Operation TPS ni 2 zar or se aii a ae 3 30 Other Warning Devices W W u ssseeeeereeeeerrnrnenee 3 7 Outlet Adjustment cece cee eect eee eee eee een eters 3 30 Outside Convex Mirror vs cc2 sed civeesesis eres 2 31 Power Mirrors 2 2 2 0 0ceceeeeeeeeeeeeeeeeeeeeeees 2 31 Overhead Console cceeceeeeeeeeeeeeeeeeeneenees 2 34 Overheated Engine Protection Operating Mode 5 25 Overseas Customer Assistance 1 7 5 Owner Checks and Services a se 6 8 Owners Canadian ccccccceceeeaeeeeeeeeeeeeeeeeeeees ii Owner s Information sssseeeeeeeerererrnnnee 7 14 Park Lamp Warning Message W ssseeeeeeeeenereee 3 52 Park P Shifting Into 5 rene elelr 2 26 Shifting OUT OF srein 2 28 Parking Brako aana NE E A EEE 2 25 Over Things That Burn sesrsiivessiisencorisersrreses 2 28 10 Parking om UlIS sasticcsz snorken kanter 4 48 Passing Hesse e E Bert se 4 15 4 47 PASS Key Ill casati eniai 2 16 PASS Key II Operation cccccceceseeeeeeeeeeees 2 16 PASS Key III Security Message 1 3 48 Perimeter Lighting ecseeeeeeneceeeeeeeeeeeees 3 18 Plan Ahead When Possible eeeeeeeeee ees 7 8 Playing a CD siccsvercies rd 3 73 3 83 3 97 Playing a Specific Loaded CD eeeeeeeeee 3 99 Playing the Radio eee 3 66 3 76 3 90 Power Accessory Outlets
165. eeeeeeeeeeeeeeees 7 13 Service Engine Soon Light in the United States or Check Engine Light in Canada 3 39 Service Manuals ccccccceceeceeceeeeeeeeeeeeaees 7 13 Setting Preset PTYs RDS Only 3 69 3 79 3 94 Setting Preset Stations 3 67 3 77 3 91 Setting the Time ccceeeeeeseeceeeeeeeeeeeeeeeeeees 3 64 Setting the Tone Bass Treble 3 67 3 77 3 92 Sheet Metal Damage eeeeeeeeeneeeeeeeeeees 5 108 Shift Lock Release n 2 25 Shifting Into Park P errenneren 2 26 Shifting Out of Park P siris near cise snusa 2 28 Shoulder Belt Height Adjuster ceeeeeeeee 1 20 Ski dan isiceveseeveverep cocyveielci inet vemeo helen tees atest 4 16 Some Other Rainy Weather Tips 1 4 22 Special Fabric Cleaning Problems 5 104 Specifications Capacities cceeceeeeeeeeeee ees 5 118 Speedometer cccseceeeeeeeeeeeaeeaeeaeeeeeaeeeeeaes 3 33 Split Bench Seats ccc ceeeeeeeeeeeeeeeeeeeeeeeeee ees 1 6 Starting Your Engine cceeeeeeeeeeeee teeter eens 2 20 Steering HERRER HERE SSR RER eE N ESen aE 4 12 Steering in Emergencies c ceeeeeeeeeeeeeeeee 4 13 Steering TIPS raiione ena aanta 4 12 Steering Wheel Controls Audio 3 117 Stereo RCA Jacks W X u ssseeeererereree renerne renerne 3 104 Storage Areas Cargo Net System sessionis iassa siinoriin
166. el remove any rust or dirt from places where the wheel attaches to the vehicle In an emergency you can use a cloth or a paper towel to do this but be sure to use a scraper or wire brush later if you need to to get all the rust or dirt off See Changing a Flat Tire in the Index 5 69 When It Is Time for New Tires 5 70 One way to tell when it s time for new tires is to check the treadwear indicators which will appear when your tires have only 1 16 inch 1 6 mm or less of tread remaining You need a new tire if any of the following statements are true You can see the indicators at three or more places around the tire You can see cord or fabric showing through the tire s rubber The tread or sidewall is cracked cut or snagged deep enough to show cord or fabric The tire has a bump bulge or split The tire has a puncture cut or other damage that can t be repaired well because of the size or location of the damage Buying New Tires To find out what kind and size of tires you need look at the tire and loading information label For an example of this label and its location sse Loading Your Vehicle on page 4 36 The tires installed on your vehicle when it was new had a Tire Performance Criteria Specification TPC Spec number on each tire s sidewall When you get new tires get ones with that same TPC Spec number That way your vehicle will continue to have tires that are designed to g
167. elt usage at deployment The module also records speed engine rpm brake and throttle data Let only qualified technicians work on your air bag systems Improper service can mean that an air bag system won t work properly See your dealer for service 1 70 Notice If you damage the covering for the driver s or the right front passenger s air bag or the air bag covering on the driver s and right front passenger s seatback the bag may not work properly You may have to replace the air bag module in the steering wheel both the air bag module and the instrument panel for the right front passenger s air bag or both the air bag module and seatback for the driver s and right front passenger s side impact air bag Do not open or break the air bag coverings Servicing Your Air Bag Equipped Vehicle Air bags affect how your vehicle should be serviced There are parts of the air bag systems in several places around your vehicle Your dealer and the service manual have information about servicing your vehicle and the air bag systems To purchase a service manual see Service Publications Ordering Information on page 13 For up to 10 seconds after the ignition key is turned off and the battery is disconnected an air bag can still inflate during improper service You can be injured if you are close to an air bag when it inflates Avoid yellow connectors They are probably part of the air bag system Be sure to fol
168. ely be resolved at a dealer s facility That is why we suggest you follow Step One first if you have a concern STEP THREE Both General Motors and your dealer are committed to making sure you are completely satisfied with your new vehicle However if you continue to remain unsatisfied after following the procedure outlined in Steps One and Two you should file with the BBB Auto Line Program to enforce any additional rights you may have Canadian owners refer to your Warranty and Owner Assistance Information booklet for information on the Canadian Motor Vehicle Arbitration Plan CAMVAP The BBB Auto Line Program is an out of court program administered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle repairs or the interpretation of the New Vehicle Limited Warranty Although you may be required to resort to this informal dispute resolution program prior to filing a court action use of the program is free of charge and your case will generally be heard within 40 days If you do not agree with the decision given in your case you may reject it and proceed with any other venue for relief available to you You may contact the BBB Auto Line Program using the toll free telephone number or write them at the following address BBB Auto Line Program Council of Better Business Bureaus Inc 4200 Wilson Boulevard Suite 800 Arlington VA 22203 1804 Telephone 1 800 955 5100 This program is a
169. ement while in this position 3 Pull the windshield wiper arm away from the windshield or backglass 4 While holding the wiper arm away from the glass push the release clip from under the blade 5 Push the release clip located at the connecting point of the blade and the arm in the up position Then pull the blade assembly down toward the glass to remove it from the wiper arm 6 Push the new wiper blade securely on the wiper arm until you hear the release clip click into place 5 57 Tires Your new vehicle comes with high quality tires made by a leading tire manufacturer If you ever have questions about your tire warranty and where to obtain service see your GM Warranty booklet for details For additional information refer to the tire manufacturer s booklet included with your vehicle s Owner s Manual Poorly maintained and improperly used tires are dangerous Overloading your tires can cause overheating as a result of too much friction You could have an air out and a serious accident See Loading Your Vehicle in the Index CAUTION Continued 5 58 Underinflated tires pose the same danger as overloaded tires The resulting accident could cause serious injury Check all tires frequently to maintain the recommended pressure Tire pressure should be checked when your tires are cold Overinflated tires are more likely to be cut punctured or broken by a sudden impact such as when
170. enance 1I Change engine oil and filter Reset oil life system See on page 5 13 An Emission Control Service Visually check for any leaks or damage See footnote j ee e ne air cleaner filter If necessary replace filter See Engine Air on page 5 18 An Emission Control Service See TOOmore Rotate tires and check inflation pressures and wear See on page 5 58 26 gt Inspect brake system See footnote a ES a eae Check engine coolant and windshield washer fluid levels and add fluid as needed Perform any needed additional services See Additional Required Services in this section Inspect suspension and steering components See footnote b Inspect wiper blades See footnote d Inspect restraint system components See footnote e Lubricate body components See footnote f Check transaxle fluid level and add fluid as needed nspect throttle system See footnote j Inspect engine cooling system See footnote c a eee Additional Required Services The following services should be performed at the first maintenance service I or II after the indicated miles kilometers shown for each item 25 000 50 000 75 000 100 000 125 000 150 000 41 500 83 000 125 000 166 000 207 500 240 000 Inspect fuel system for damage or leaks Inspect exhaust system for loose or damaged components enone Air Cleaner Filter on Control Change automatic transaxle fluid and filter sever
171. encies Display messages from radio stations Seek to stations with traffic announcements 3 89 This system relies upon receiving specific information from these stations and will only work when the information is available In rare cases a radio station may broadcast incorrect information that will cause the radio features to work improperly If this happens contact the radio station While you are tuned to an RDS station the station name or the call letters will appear on the display instead of the frequency DS stations may also provide the time of day a program type PTY for current programming and the name of the program being broadcast XM Satellite Radio Service 48 Contiguous US States XM is a continental U S based satellite radio service that offers 100 coast to coast channels including music news sports talk and children s programming XM provides digital quality audio and text information including song title and artist name A service fee is required in order to receive the XM service For more information contact XM at www xmradio com or call 1 800 852 XMXM 9696 3 90 Playing the Radio PWR Power Push this knob to turn the system on and off VOLUME Turn this knob to increase or to decrease volume AUTO VOL Automatic Volume Your system has a feature called automatic volume With this feature your audio system adjusts automatically to make up for road and wind noi
172. er arrow for more than 2 seconds will search the previous or next tracks at 2 tracks per second When you see the track number that you would like to play release the button to stop searching and to play the track A SCAN V Press and hold either arrow for more than two seconds until SCAN and the track number appear on the display and you hear a beep The CD will go to the next track play for a few seconds then go on to the next track Press either arrow again to stop scanning RCL Recall Push this knob to see how long the current track has been playing To change the default on the display track and elapsed time push the knob until you see the display you want then hold the knob until the display flashes The selected display will now be the default While elapsed time is showing CD TIME will appear on the display 3 84 BAND Press this button to listen to the radio when a CD is playing The inactive CD will remain safely inside the radio for future listening CD AUX Auxiliary Press this button to play a CD when listening to the radio The CD symbol will appear on the display when a CD is loaded EJECT Press this button to eject a CD Eject may be activated with either the ignition or radio off CDs may be loaded with the radio and ignition off if this button is pressed first Using an MP3 CD MP3 Format This MP3 player will accept MP3 files that were recorded on an up to 700 MB CD R CD The files can be recor
173. er behavior factors are far more often the cause of a utility vehicle rollover than are environmental or vehicle factors Safe driver behavior and understanding the environment in which you will be driving can help avoid a rollover crash in any type of vehicle including utility vehicles Defensive Driving The best advice anyone can give about driving is Drive defensively Please start with a very importan afe vehicle Buckle up See Safety Belts They i a eon page 1 12 Defensive driving really means be ready for anything On city streets rural roads or freeways it means always expect the unexpected Assume that pedestrians or other drivers are going to be careless and make mistakes Anticipate what they might do Be ready for their mistakes Rear end collisions are about the most preventable of accidents Yet they are common Allow enough following distance It is the best defensive driving maneuver in both city and rural driving You never know when the vehicle in front of you is going to brake or turn suddenly Defensive driving requires that a driver concentrate on the driving task Anything that distracts from the driving task such as concentrating on a cellular telephone call reading or reaching for something on the floor makes proper defensive driving more difficult and can even cause a collision with resulting injury Ask a passenger to help do things like this or pull off the road in a
174. er is not fully in PARK P with the parking brake firmly set And if you leave the vehicle with the engine running it could overheat and even catch fire You or others could be injured Do not leave your vehicle with the engine running lf you have to leave your vehicle with the engine running be sure your vehicle is in PARK P and your parking brake is firmly set before you leave it After you have moved the shift lever into PARK P hold the regular brake pedal down Then see if you can move the shift lever away from PARK P without first pulling it toward you If you can it means that the shift lever was not fully locked into PARK P Torque Lock If you are parking on a hill and you do not shift your transaxle into PARK P properly the weight of the vehicle may put too much force on the parking pawl in the transaxle You may find it difficult to pull the shift lever out of PARK P This is called torque lock To prevent torque lock set the parking brake and then shift into PARK P properly before_you leave the driver s seat To find out how seefShifing Into Park PJ on page 2 26 When you are ready to drive move the shift lever out of PARK P before you release the parking brake If torque lock does occur you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transaxle so you can pull the shift lever out of PARK P 2 27 Shifting Out
175. er side of the WDO LOCK switch for normal window operation Sun Visors To block out glare you can swing down the visors You can also remove them from the center mount and swing them to the side There may be an extension on the inboard side of the sun visors Pull the extension out to block out glare Visor Vanity Mirror Pull down the sun visor Flip up the cover to expose the vanity mirror 2 13 Theft Deterrent Systems Vehicle theft is big business especially in some cities Although your vehicle has a number of theft deterrent features we know that nothing we put on it can make it impossible to steal Content Theft Deterrent Your vehicle may have a theft deterrent alarm system A light located on top of the instrument panel will flash slowly to let you know that the system has been armed While armed the doors will not unlock with the power door lock switch Once armed the alarm will go off if someone tries to open one of the doors on the vehicle without the remote keyless entry transmitter or the key or tries to turn the ignition without using the correct key The horn will sound and the headlamps and parking lamps will flash any time the alarm sounds If you would like to change the way the headlamps parking lamps and horn operate with the content theft deterrent system and your vehicle is equipped with the Driver Information Center DIC see D G Vehicle Personalization on page 3 57 When the
176. erent tone Adjusting the Speakers Balance Fade BAL Balance To adjust the balance between the right and the left speakers press and release this button until BAL appears on the display The SELECT LED indicator will light to show that the speakers can be adjusted Turn the SELECT knob to move the sound toward the right or the left speakers FADE To adjust the fade between the front and the rear speakers press and release this button until FADE appears on the display The SELECT LED indicator will light to show that the speakers can be adjusted Turn the SELECT knob to move the sound toward the front or the rear speakers Pressing and holding the BAL FADE button for two seconds will return all speaker settings to the middle position 3 68 Finding a Program Type PTY Station RDS and XM To select and find a desired PTY perform the following 1 Press PROG TYPE to activate program type select mode The PTY symbol will appear on the display 2 Turn the SELECT knob to select a PTY 3 Once the desired PTY is displayed press either SEEK arrow to select the PTY and take you to the PTY s first station 4 If you want to go to another station within that PTY and the PTY is displayed press either SEEK arrow once If the PTY is not displayed press either SEEK arrow twice to display the PTY and then to go to another station 5 Press PROG TYPE to exit program type select mode If PTY times out and is no longe
177. ers could be burned Use a 50 50 mixture of clean drinkable water and DEX COOL coolant Notice If you use an improper coolant mixture your engine could overheat and be badly damaged The repair cost wouldn t be covered by your warranty Too much water in the mixture can freeze and crack the engine radiator heater core and other parts If you have to add coolant more than four times a year have your dealer check your cooling system Notice If you use the proper coolant you don t have to add extra inhibitors or additives which claim to improve the system These can be harmful 5 23 Checking Coolant The coolant recovery tank is located on the driver s side of the vehicle above the engine air cleaner filter See Engine on page 5 72 for more information on location DEX COOL The vehicle must be on a level surface When your engine is cold the coolant level should be at the FULL COLD mark or a little higher When your engine is warm the level should be above the FULL COLD mark or a little higher 5 24 Adding Coolant If you need more coolant add the proper DEX COOL coolant mixture at the coolant recovery tank Turning the radiator pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly With the coolant recovery tank you will almost never have to add coolant at the radiator Never turn the radiator pressure cap even a lit
178. es may not work well or they may not even work at all This could cause a crash Always use the proper brake fluid Notice Using the wrong fluid can badly damage brake system parts For example just a few drops of mineral based oil such as engine oil in your brake system can damage brake system parts so badly that they will have to be replaced Do not let someone put in the wrong kind of fluid If you spill brake fluid on your vehicle s painted surfaces the paint finish can be damaged Be careful not to spill brake fluid on your vehicle If you do wash it off immediately See Appearance Care on page 5 103 5 39 Brake Wear Your vehicle has four wheel disc brakes Disc brake pads have built in wear indicators that make a high pitched warning sound when the brake pads are worn and new pads are needed The sound may come and go or be heard all the time your vehicle is moving except when you are pushing on the brake pedal firmly The brake wear warning sound means that soon your brakes will not work well That could lead to an accident When you hear the brake wear warning sound have your vehicle serviced 5 40 Notice Continuing to drive with worn out brake pads could result in costly brake repair Some driving conditions or climates may cause a brake squeal when the brakes are first applied or lightly applied This does not mean something is wrong with your brakes Properly torqued wheel nuts a
179. ess the SET button at the end of the lever until you reach the lower speed you want then release it To slow down in very small amounts press the SET button briefly Each time you do this you will go about 1 mph 1 6 km h slower Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase your speed When you take your foot off the pedal your vehicle will slow down to the cruise control speed you set earlier Using Cruise Control on Hills How well your cruise control will work on hills depends upon your speed load and the steepness of the hills When going up steep hills you may have to step on the accelerator pedal to maintain your speed When going downhill you may have to brake or shift to a lower gear to keep your speed down Of course applying the brake takes you out of cruise control Many drivers find this to be too much trouble and don t use cruise control on steep hills Ending Cruise Control There are two ways to turn off the cruise control Step lightly on the brake pedal Move the cruise control switch to OFF Erasing Cruise Memory When you turn off the cruise control or the ignition your cruise control set speed memory is erased Exterior Lamps The control located to the left of the steering column operates the exterior lamps The exterior lamp control has three positions AUTO Automatic Headlamp Control Off Turning the control to this position will activ
180. essage will come on when the ignition is turned to ON or START and the driver s or passenger s door is open 3 47 Rear Hatch Ajar Warning Message Canada United States This message will come on when the ignition is turned to ON or START and the liftgate is open 3 48 PASS Key III Security Message P A United States Canada If you are ever driving and this message comes on and stays on you will be able to restart your engine if you turn it off Your PASS Key III system however is not working properly and must be serviced by your dealer Your vehicle is not protected by the PASS Key III system at this time See PASS Key Ilion page 2 16 for more information All Wheel Drive Disable Warning Message Canada AWD DISABLE United States Your vehicle may have this message If it does it will come on when there is a spare tire on the vehicle or when the anti lock brake system warning light comes on or when the rear differential fluid is overheating This message will go out when the differential fluid cools The all wheel drive system will be disabled until the compact spare tire is replaced by a full size tire If the warning message is still on after putting on the full size tire you need to reset the warning message To reset the warning message turn the ignition off and then back on again If the message stays on see your dealer right away See Al Wheel Drive AWD Systemfon page 4
181. essory Power under Ignition Positions on page 2 18 for more information Notice Opening the sunroof when the luggage rack crossrails are not in the full rear position could cause damage to the sunroof or luggage rack Verify the luggage rack crossrails are in the full rear position before opening the sunroof When vent opening the sunroof the sunshade must be opened by hand Press the rear of the switch to vent open the glass panel Press the rear of the switch a second time and release it to express open the glass panel The glass panel and sunshade will fully open When the glass panel is express opening pressing the switch in either direction will stop it If you press and hold the rear of the switch the express open operation will be overridden To close the glass panel press and hold the front of the switch until the glass panel stops Section 3 Instrument Panel Instrument Panel Overview eeee 3 4 Engine Coolant Temperature Gage 1 1 1 1 3 39 Hazard Warning Flashers eeeeeeeneeeee ee 3 6 Malfunction Indicator Lamp eeeeeeeeeee 3 39 Other Warning Devices ceeeeeeeeeneeeeeneees 3 7 Fugl GAQe iraniana ea Stentest RRE ENE Ser 3 42 Horn nE r eee EA A E A AOU 3 7 Message Center secure 3 43 Tilt Wheel Sorria pes FEEEE FEDERER LEE EEE REE EEELEEEEE RER KERERE 3 7 Service Traction System Warning Message 3 43 Turn Signal Multifunction LEVEI cu
182. etermine the current mode or to change the mode do the following 1 Follow the instructions for Entering Programming Mode listed previously 2 Follow the instructions for programming HEADLAMP EXIT DELAY earlier in this section to make sure which mode it is programmed to 3 Press the SET button until UNLOCK FEEDBACK appears on the DIC 4 Press the MODE button until the arrow is before LIGHTS or OFF 5 Press the SET button once you have determined which mode you prefer The mode you selected is now set You can either exit programming mode by following the instructions later in this section or program the next feature available on your vehicle Lock Feedback The lock feedback feature can be programmed to one of the following modes OFF When LOCK is pressed on the remote keyless entry transmitter the headlamps and parking lamps will not flash and the horn will not sound LIGHTS When LOCK is pressed on the remote keyless entry transmitter the headlamps and parking lamps will flash briefly HORN When LOCK is pressed on the remote keyless entry transmitter the headlamps and parking lamps will flash briefly and the horn will sound Your vehicle was originally programmed to HORN The mode may have been changed since then To determine the current mode or to change the mode do the following 1 Follow the instructions for Entering Programming Mode listed previously 2 Press the MODE button unt
183. everereerererere When Should an Air Bag Inflate W What Makes an Air Bag Inflate 1 How Does an Air Bag Restrain 0 What Will You See After an Air Bag Inflates Servicing Your Air Bag Equipped Vehicle Restraint System Check e eeeeeeeeee ee Checking Your Restraint Systems 0 Replacing Restraint System Parts Aftera Crash aan aldre seen 1 64 1 67 1 68 1 68 1 69 Front Seats Six Way Power Seats Your vehicle may have this Manual Passenger Seat feature If it does the six way power seat control Pull up on the lever is located on the outboard located on the front of the sides of the driver s and seat to unlock and front passenger s seats move the seat Move the front of the control up or down to adjust the front portion of the cushion up or down Move the rear of the control up or down to adjust the rear portion of the cushion up or down Slide the seat to where you want it and release the Lift up or push down on the whole control to move lever To make sure the seat is locked into place try to the entire seat up or down move the seat back and forth with your body To move the whole seat forward or rearward slide the control forward or rearward Manual Lumbar The knob that controls this feature is located on the outboard sides of the driver s and front passenger s seats Turn the knob toward the front
184. extend can be injured and both your vehicle and the the life of your transaxle trailer can be damaged But if you ever have to park your rig on a hill do the following 1 Apply your regular brakes but do not shift into PARK P yet 2 Have someone place chocks under the trailer wheels 3 When the wheel chocks are in place release the regular brakes until the chocks absorb the load 4 Reapply the regular brakes Then apply your parking brake and then shift to PARK P 5 Release the regular brakes 4 48 When You Are Ready to Leave After Parking on a Hill 1 Apply your regular brakes and hold the pedal down while you do the following Start your engine Shift into a gear Release the parking brake 2 Let up on the brake pedal 3 Drive slowly until the trailer is clear of the chocks 4 Stop and have someone pick up and store the chocks Maintenance When Trailer Towing Your vehicle will need service more often when you are pulling a trailer See the Maintenance Schedule for more on this Things that are especially important in trailer operation are automatic transaxle fluid engine oil belts cooling system and brake system Each of these is covered in this manual and the Index will help you find them quickly If you are trailering it is a good idea to review these sections before you start your trip Check periodically to see that all hitch nuts and bolts are tight Trailer Wiring Harness
185. f you have recently replaced your battery or if your battery has run down The diagnostic system is designed to evaluate critical emission control systems during normal driving This may take several days of routine driving If you have done this and your vehicle still does not pass the inspection for lack of OBD system readiness your GM dealer can prepare the vehicle for inspection 3 42 Fuel Gage Canada United States When the indicator nears empty you still have a little fuel left but you should get more soon If your fuel is low the warnin ing e in the me center will come on See Low Fuel Warning Message on page 3 50 later in this section Your fuel gage tells you about how much fuel you have left when the ignition is on Here are four things that some owners ask about All these things are normal and do not indicate that anything is wrong with the fuel gage At the gas station the gas pump shuts off before the gage reads full It takes a little more or less fuel to fill up than the gage reads For example the gage reads half full but it took more or less than half of the tank s capacity to fill it The gage pointer may move while cornering braking or speeding up The gage may not indicate empty when the ignition is turned off Message Center The message center is located in the instrument panel cluster at the bottom of the tachometer It gives you important safety and mainte
186. f a side impact air bag When Should an Air Bag Inflate The driver s and right front passenger s frontal air bags are designed to inflate in moderate to severe frontal or near frontal crashes But they are designed to inflate only if the impact speed is above the system s designed threshold level lf your vehicle goes straight into a wall that doesn t move or deform the threshold level is about 12 to 19 mph 19 to 31 km h The threshold level can vary however with specific vehicle design so that it can be somewhat above or below this range If your vehicle strikes something that will move or deform such as a parked car the threshold level will be higher The drivers and right front passenger s frontal air bags are not designed to inflate in rollovers rear impacts or in many side impacts because inflation would not help the occupant Your vehicle may or may not have a side impact air bag See Air Bag Systems on page 1 61 Side impact air bags are designed to inflate in moderate to severe side crashes A side impact air bag will inflate if the crash severity is above the system s designed threshold level The threshold level can vary with specific vehicle design Side impact air bags are not designed to inflate in frontal or near frontal impacts rollovers or rear impacts because inflation would not help the occupant A side impact air bag will only deploy on the side of the vehicle that is struck In any
187. feature called song list This feature is capable of saving 20 track selections To save tracks into the song list feature perform the following steps 1 Turn the CD player on and load it with at least one CD See LOAD CD listed previously in this section for more information 2 Check to see that the CD changer is not in song list mode S LIST should not appear in the display If S LIST is present press the SONG LIST button to turn it off 3 Select the desired CD by pressing the numbered pushbutton and then use the SEEK SCAN right arrow button to locate the track that you want to save The track will begin to play 4 Press and hold the SONG LIST button to save the track into memory When SONG LIST is pressed a beep will be heard immediately After two seconds of continuously pressing SONG LIST two beeps will sound to confirm that the track has been saved 5 Repeat Steps 3 and 4 for saving other selections S LIST FULL will appear on the display if you try to save more than 20 selections To play the song list press the SONG LIST button One beep will be heard and S LIST will appear on the display The recorded tracks will begin to play in the order that they were saved You may seek through the song list by using the SEEK SCAN arrows Seeking past the last saved track will return you to the first saved track To delete tracks from the song list perform the following steps 1 Turn the CD player on 2 Press t
188. floor track assembly 2 Pull the tray toward you without lifting it up You will hear a click when the tray is locked into the extended position 3 Push the release lever again to roll the tray back into the vehicle You will hear a click when the tray is locked into position The sliding rear convenience tray also has storage areas in it Pull up on the covers to open them Be sure to close the covers once you are done loading or unloading them The sliding rear convenience tray has a maximum weight capacity of 400 Ibs 181 4 kg on top Notice Loading objects that weigh over 400 Ibs 181 kg onto the sliding rear convenience tray may cause damage Repairs would not be covered by your warranty Do not load heavy objects on the sliding rear convenience tray 2 43 Removing the Sliding Rear Convenience Tray 1 Make sure that all items have been removed from the top and the inside of the sliding rear convenience tray 2 Push down on the release lever and pull the tray fully rearward onto the tailgate until you hear a click 3 Disconnect the tethered ring from the hook and place the tethered ring on the outer edge of the tailgate on each side of the vehicle 2 44 4 Push down on the release lever and roll the tray into the vehicle approximately 6 inches 15 24 cm 5 Use the handle to lift up on the tray while pulling it towards you Use your other hand to support and lift the tray from the bottom Remo
189. following reasons It is very hot When the temperature returns to normal the CD should play You are driving on a very rough road When the road becomes smoother the CD should play The CD is dirty scratched wet or upside down The air is very humid If so wait about an hour and try again There may have been a problem while burning the CD The label may be caught in the CD player If the CD is not playing correctly for any other reason try a known good CD If any error occurs repeatedly or if an error cannot be corrected contact your dealer If your radio displays an error message write it down and provide it to your dealer when reporting the problem Rear Seat Entertainment System Your vehicle may have a Digital Versatile Disc DVD system The Rear Seat Entertainment RSE includes a DVD player a video display screen two sets of cordless headphones and a remote control Before You Drive The RSE is designed for rear seat passengers only The driver cannot safely view the video screen while driving and should not try to do so Your DVD system is designed to be inoperable when the vehicle is exposed to extremely low or high temperatures in order to protect your system from damage Operate your DVD system under normal or comfortable cabin temperature ranges Headphones The entertainment system includes two cordless headphones The cordless headphones have an ON OFF switch and a volume
190. foot on the regular brake set the parking brake To check the parking brake s holding ability With the engine running and transaxle in NEUTRAL N slowly remove foot pressure from the regular brake pedal Do this until the vehicle is held by the parking brake only To check the PARK P mechanism s holding ability With the engine running shift to PARK P Then release the parking brake followed by the regular brake Contact your GM Goodwrench dealer if service is required Underbody Flushing Service At least every spring use plain water to flush any corrosive materials from the underbody Take care to clean thoroughly any areas where mud and other debris can collect Recommended Fluids and Lubricants Fluids and lubricants identified below by name part number or specification may be obtained from your dealer Usage Fluid Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol To determine the proper viscosity for your vehicle s engine see on page 5 13 50 50 mixture of clean drinkable water and use only Engine Oil Engine Coolant p OOL Coolant See X See Engine on page 5 22 Hydraulic Brake Delco Supreme 11 Brake Fluid or System equivalent DOT 3 brake fluid Windshiel ce ete GM Optikleen Washer Solvent GM Power Steering Fluid Power Steering GM Part No U S 89021184 in y Can
191. from all painted surfaces on your vehicle Sheet Metal Damage If your vehicle is damaged and requires sheet metal repair or replacement make sure the body repair shop applies anti corrosion material to parts repaired or replaced to restore corrosion protection Original manufacturer replacement parts will provide the corrosion protection while maintaining the warranty Finish Damage Any stone chips fractures or deep scratches in the finish should be repaired right away Bare metal will corrode quickly and may develop into major repair expense Minor chips and scratches can be repaired with touch up materials avaliable from your dealer Larger areas of finish damage can be corrected in your dealer s body and paint shop Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody If these are not removed corrosion and rust can develop on the underbody parts such as fuel lines frame floor pan and exhaust system even though they have corrosion protection At least every spring flush these materials from the underbody with plain water Clean any areas where mud and debris can collect Dirt packed in close areas of the frame should be loosened before being flushed Your dealer or an underbody car washing system can do this for you Chemical Paint Spotting Some weather and atmospheric conditions can create a chemical fallout Airborne pollutants can fall upon and attack
192. from the factory If CALIBRATE appears on the display it means that your radio has not been configured properly for your vehicle and must be returned to the dealer for service XM Radio Messages Radio Display 2 XL Explicit Language XL on the radio display These channels or any others can be blocked at a Channels after the channel name customer s request by calling 1 800 852 XMXM 9696 indicates content with explicit language Updating Updating The encryption code in your receiver is being updated and encryption code no action is required This process should take no longer than 30 seconds No Signal Loss of signal Your system is functioning correctly but you are in a location that is blocking the XM signal When you move into an open area the signal should return Loading XM Acquiring channel audio Your radio system is acquiring and processing audio and after 4 second delay text data No action is needed This message should disappear shortly CH Off Air Channel not in service This channel is not currently in service Tune to another channel CH Unavail Channel no longer This previously assigned channel is no longer assigned available Tune to another station If this station was one of your presets you may need to choose another station for that preset button 3 71 Radio Display No Info Artist Name Feature not available No Info Song Program Title not available No Info Category Name not av
193. from the windshield more quickly Turn the right knob to select the defog or defrost mode N Defog This mode directs air to the windshield and the floor outlets When you select this mode the system turns off recirculation and runs the air conditioning compressor unless the outside temperature is at or below freezing The recirculation mode cannot be selected while in the defog mode W Defrost Pressing this button directs most of the air to the windshield and the side window outlets with some air directed to the floor outlets In this mode the system will automatically turn off recirculation and run the air conditioning compressor unless the outside temperature is at or below freezing Recirculation cannot be selected while in the defrost mode Do not drive the vehicle until all the windows are clear 3 26 Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window GW REAR Press this button to turn the rear window defogger on or off An indicator light in the button will come on to let you know that the rear window defogger is activated The rear window defogger will turn off about 10 minutes after the button is pressed If turned on again the defogger will only run for about five minutes before turning off The defogger can also be turned off by pressing the button again or by turning off the engine Notice Don t use anything sharp on the inside of the rear window If
194. ft Lock Control System Check When you are doing this inspection the vehicle could move suddenly If the vehicle moves you or others could be injured 1 Before you start be sure you have enough room around the vehicle It should be parked on a level surface 2 Firmly apply the parking brake See Parking Brake on page 2 25 if necessary Be ready to apply the regular brake immediately if the vehicle begins to move 3 With the engine off turn the key to the RUN position but don t start the engine Without applying the regular brake try to move the shift lever out of PARK P with normal effort If the shift lever moves out of PARK P contact your GM Goodwrench dealer for service Ignition Transaxle Lock Check While parked and with the parking brake set try to turn the ignition key to LOCK in each shift lever position The key should turn to LOCK only when the shift lever is in PARK P The key should come out only in LOCK Contact your GM Goodwrench dealer if service is required Parking Brake and Automatic Transaxle Park P Mechanism Check When you are doing this check your vehicle could begin to move You or others could be injured and property could be damaged Make sure there is room in front of your vehicle in case it begins to roll Be ready to apply the regular brake at once should the vehicle begin to move Park on a fairly steep hill with the vehicle facing downhill Keeping your
195. g as two or three seconds or more with another Age physical condition alertness coordination and eyesight all play a part So do alcohol drugs and frustration But even in 3 4 of a second a vehicle moving at 60 mph 100 km h travels 66 feet 20 m That could be a lot of distance in an emergency so keeping enough space between your vehicle and others is important And of course actual stopping distances vary greatly with the surface of the road whether it is pavement or gravel the condition of the road wet dry icy tire tread the condition of your brakes the weight of the vehicle and the amount of brake force applied Avoid needless heavy braking Some people drive in spurts heavy acceleration followed by heavy braking rather than keeping pace with traffic This is a mistake Your brakes may not have time to cool between hard stops Your brakes will wear out much faster if you do a lot of heavy braking If you keep pace with the traffic and allow realistic following distances you will eliminate a lot of unnecessary braking That means better braking and longer brake life If your engine ever stops while you are driving brake normally but do not pump your brakes If you do the pedal may get harder to push down If your engine stops you will still have some power brake assist But you will use it when you brake Once the power assist is used up it may take longer to stop and the brake pedal will be harder
196. g takes correct equipment and it has to be used properly That is the reason for this section In it are many time tested important trailering tips and safety rules Many of these are important for your safety and that of your passengers So please read this section carefully before you pull a trailer Load pulling components such as the engine transaxle wheel assemblies and tires are forced to work harder against the drag of the added weight The engine is required to operate at relatively higher speeds and under greater loads generating extra heat The trailer also adds considerably to wind resistance increasing the pulling requirements If You Do Decide To Pull A Trailer If you do here are some important points There are many different laws including speed limit restrictions having to do with trailering Make sure your rig will be legal not only where you live but also where you will be driving A good source for this information can be state or provincial police Consider using a sway control See Hitches later in this section Do not tow a trailer at all during the first 500 miles 800 km your new vehicle is driven Your engine axle or other parts could be damaged Then during the first 500 miles 800 km that you tow a trailer do not drive over 50 mph 80 km h and do not make starts at full throttle This helps your engine and other parts of your vehicle wear in at the heavier loads You c
197. gine performance when the air conditioning compressor shuts off and turns on again This is normal The system is designed to make adjustments to help with fuel economy while still maintaining the selected temperature On hot days open the windows to let hot inside air escape then close them This helps to reduce the time it takes for your vehicle to cool down It also helps the system to operate more efficiently For quick cool down on hot days do the following 1 Select the vent mode 2 Select the coolest temperature 3 Select the highest fan speed 4 Select A C 5 Select the recirculation mode Using these settings together for long periods of time may cause the air inside of your vehicle to become too dry To prevent this from happening after the air inside of your vehicle has cooled turn the recirculation mode off The air conditioning system removes moisture from the air so you may sometimes notice a small amount of water dripping underneath your vehicle while idling or after turning off the engine This is normal 3 25 Defogging and Defrosting Fog on the inside of windows is a result of high humidity or moisture condensing on the cool window glass This can be minimized if the climate controls system is used properly There are two modes to clear fog or frost from your windshield Use the defog mode to clear the windows of fog or moisture and warm the passengers Use the defrost mode to remove fog or frost
198. gn However NHTSA cannot become involved in individual problems between you your dealer or General Motors To contact NHTSA you may either call the Auto Safety Hotline toll free at 1 800 424 9393 or 366 0123 in the Washington D C area or write to NHTSA U S Department of Transportation Washington D C 20590 You can also obtain other information about motor vehicle safety from the hotline Reporting Safety Defects to the Canadian Government If you live in Canada and you believe that your vehicle has a safety defect you should immediately notify Transport Canada in addition to notifying General Motors of Canada Limited You may write to Transport Canada 330 Sparks Street Tower C Ottawa Ontario K1A ON5 Reporting Safety Defects to General Motors In addition to notifying NHTSA or Transport Canada in a situation like this we certainly hope you ll notify us Please call us at 1 800 762 2737 or write Pontiac GMC Customer Assistance Center P O Box 33172 Detroit MI 48232 5172 In Canada please call us at 1 800 263 3777 English or 1 800 263 7854 French Or write General Motors of Canada Limited Customer Communication Centre 163 005 1908 Colonel Sam Drive Oshawa Ontario L1H 8P7 Service Publications Ordering Information Service Manuals Service Manuals have the diagnosis and repair information on engines transmission axle suspension brakes electrical steering body etc RETAIL SEL
199. h the sales transaction or the operation of your vehicle will be resolved by your dealer s sales or service departments Sometimes however despite the best intentions of all concerned misunderstandings can occur If your concern has not been resolved to your satisfaction the following steps should be taken STEP ONE Discuss your concern with a member of dealership management Normally concerns can be quickly resolved at that level If the matter has already been reviewed with the sales service or parts manager contact the owner of the dealership or the general manager STEP TWO If after contacting a member of dealership management it appears your concern cannot be resolved by the dealership without further help contact the Pontiac Customer Assistance Center by calling 1 800 762 2737 In Canada contact GM of Canada Customer Communication Centre in Oshawa by calling 1 800 263 3777 English or 1 800 263 7854 French We encourage you to call the toll free number in order to give your inquiry prompt attention Please have the following information available to give the Customer Assistance Representative Vehicle Identification Number This is available from the vehicle registration or title or the plate at the top left of the instrument panel and visible through the windshield Dealership name and location Vehicle delivery date and present mileage When contacting Pontiac please remember that your concern will lik
200. h the liftgate tailgate open or if electrical wiring or other cable connections must pass through the seal between the body and the liftgate tailgate Make sure all other windows are shut Turn the fan on your heating or cooling system to its highest speed and select the control setting that will force outside air Sys af vehicle See Climate Contro on page 3 24 If you have air outlets on or under the instrument panel open them all the way See Engine Exhausi on page 2 29 Liftgate Tailgate Release To open the liftgate from the inside of the vehicle press the liftgate release button located on the instrument panel switchbank ao To open the liftgate from the outside of the vehicle insert the key into the lock and turn it clockwise or press REAR on the remote keyless entry transmitter Your vehicle must be in PARK P or NEUTRAL N for the liftgate to release The liftgate will lock when closed You will have to use one of the previous options to open the liftgate again The liftgate must be opened to release the tailgate Once the liftgate is opened reach inside the tailgate to lift the handle Open the tailgate Make sure the tailgate is closed before closing the liftgate Notice If you close the tailgate without first closing the liftgate glass damage or breakage may occur Always close the liftgate glass first Windows Leaving children in a vehicle with the windows closed is dange
201. h the protective cap Notice Leaving electrical equipment on for extended periods will drain the battery Always turn off electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating Certain electrical accessories may not be compatible to the accessory power outlet and could result in blown vehicle or adapter fuses If you experience a problem see your dealer for additional information on accessory power outlets Notice Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should The repairs would not be covered by your warranty Check with your dealer before adding electrical equipment When adding electrical equipment be sure to follow the proper installation instructions included with the equipment Notice Improper use of the power outlet can cause damage not covered by your warranty Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only Ashtrays and Cigarette Lighter If your vehicle has an ashtray and cigarette lighter they are located in the glove box The ashtray fits into the cupholders The cigarette lighter installs into the accessory power outlet in the instrument panel switchbank To use the lighter push it in all the way and let go When it s ready it will pop back out by itself Notice Holding a cigarette lighter i
202. he SONG LIST button to turn song list on S LIST will appear on the display 3 Press the SEEK SCAN arrows to select the desired track to be deleted 4 Press and hold the SONG LIST button for two seconds When SONG LIST is pressed a beep will be heard immediately After two seconds of continuously pressing the SONG LIST button two beeps will be heard to confirm that the track has been deleted 3 101 After a track has been deleted the remaining tracks are moved up the list When another track is added to the song list the track will be added to the end of the list To delete the entire song list perform the following steps 1 Turn the CD player on 2 Press the SONG LIST button to turn song list on S LIST will appear on the display 3 Press and hold the SONG LIST button for more than four seconds A beep will be heard followed by two beeps after two seconds and a final beep will be heard after four seconds S LIST EMPTY will appear on the display indicating that the song list has been deleted If a CD is ejected and the song list contains saved tracks from that CD those tracks are automatically deleted from the song list Any tracks saved to the song list again are added to the bottom of the list To end song list mode press the SONG LIST button One beep will be heard and S LIST will be removed from the display 3 102 CD Messages CHECK CD If this message appears on the radio display it could be for one of the
203. he file structure and determined where the first playable track is located READING DISC will appear on the display After the MP3 has been read the number of folders and tracks will be displayed then the radio will go back to the default display The CD symbol will appear on the display If you want to insert an MP3 with the ignition off first press the EJECT button or push the RCL knob If you insert a CD with the radio off and the ignition on it will start to play If you select an EQ setting for your CD it will be activated each time you play a CD As each new track starts to play the track number will appear on the display The CD player can play the smaller 8cm single CDs with an adapter ring Full size CDs and the smaller CDs are loaded in the same manner If playing a CD R the sound quality may be reduced due to CD R quality the method of recording the quality of the music that has been recorded and the way the CD R has been handled You may experience an increase in skipping difficulty in finding tracks and or difficulty in loading and ejecting If these problems occur try a known good CD Do not add paper labels to CDs they could get caught in the CD player Do not play 3 inch CA3 CDs without a standard adapter CD If an error appears on the display see CD Messages later in this section DD 1 Forward Press and hold this pushbutton to advance quickly within a track Press and hold this pushbutton for
204. he first is that the brake fluid goes down to an acceptable level during normal brake lining wear When new linings are put in the fluid level goes back up The other reason is that fluid is leaking out of the brake system If it is you 5 38 should have your brake system fixed since a leak means that sooner or later your brakes will not work well or will not work at all So it is not a good idea to top off your brake fluid Adding brake fluid will not correct a leak If you add fluid when your linings are worn then you will have too much fluid when you get new brake linings You should add or remove brake fluid as necessary only when work is done on the brake hydraulic system If you have too much brake fluid it can spill on the engine The fluid will burn if the engine is hot enough You or others could be burned and your vehicle could be damaged Add brake fluid only when work is done on the brake hydraulic system United States Canada When your brake fluid falls to a low level your brake warning light will come on See Brake System Warning on page 3 36 What to Add When you do need bee ae use only ae a Brake fluid Use pn b on ed Recommended Fluids and Tuercanta on only See page 6 12 Always clean the brake fluid reservoir cap and the area around the cap before removing it This will help keep dirt from entering the reservoir With the wrong kind of fluid in your brake system your brak
205. he interior lamps will fade out The lamps will fade out before the 25 seconds if one of the following occurs The ignition is turned to ON All doors are locked using the remote keyless entry transmitter The interior lamp override is turned on There is no occupant activity detected for an illumination period of 25 seconds Your vehicle was originally programmed to ON The mode may have been changed since then To determine the current mode or to change the mode do the following 1 Follow the instructions for Entering Programming Mode listed previously 2 Press the MODE button until INTERIOR LIGHTING DELAY appears on the DIC 3 Press the SET button until the arrow is before ON or OFF The mode you selected is now set You can either exit programming mode by following the instructions later in this section or program the next feature available on your vehicle Interior Lighting On The interior lighting on feature can be programmed to one of the following modes KEY OUT The interior lamps will come on for about 25 seconds whenever you remove the key from the ignition DOOR The interior lamps will come on for about 25 seconds when any door is opened Interior lighting on will not occur while the ignition is in ON After 25 seconds the interior lamps will fade out The lamps will fade out before the 25 seconds if one of the following occurs The ignition is turned to ON e LOCK is pressed on
206. he key and the accelerator pedal Notice Your engine is designed to work with the electronics in your vehicle If you add electrical parts or accessories you could change the way the engine operates Before adding electrical equipment check with your dealer If you do not your engine might not perform properly Engine Coolant Heater Your vehicle may have an engine coolant heater In very cold weather 0 F 18 C or colder the engine coolant heater can help You ll get easier starting and better fuel economy during engine warm up Usually the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle At temperatures above 32 F 0 C use of the coolant heater is not required To Use the Engine Coolant Heater 1 Turn off the engine 2 Open the hood and unwrap the electrical cord The electrical cord is located on the driver s side of the engine compartment 3 Plug it into a normal grounded 110 volt AC outlet Plugging the cord into an ungrounded outlet could cause an electrical shock Also the wrong kind of extension cord could overheat and cause a fire You could be seriously injured Plug the cord into a properly grounded three prong 110 volt AC outlet If the cord will not reach use a heavy duty three prong extension cord rated for at least 15 amps 4 Before starting the engine be sure to unplug and store the cord as it was before to keep it away from moving engine p
207. he restraint will be compatible with the motor vehicle in which it will be used 1 43 For most basic types of child restraints there are many different models available When purchasing a child restraint be sure it is designed to be used in a motor vehicle If it is the restraint will have a label saying that it meets federal motor vehicle safety standards The restraint manufacturer s instructions that come with the restraint state the weight and height limitations for a particular child restraint In addition there are many kinds of restraints available for children with special needs Newborn infants need complete support including support for the head and neck This is necessary because a newborn infant s neck is weak and its head weighs so much compared with the rest of its body In a crash an infant in a rear facing seat settles into the restraint so the crash forces can be distributed across the strongest part of an infant s body the back and shoulders Infants always should be secured in appropriate infant restraints 1 44 The body structure of a young child is quite unlike that of an adult or older child for whom the safety belts are designed A young child s hip bones are still so small that the vehicle s regular safety belt may not remain low on the hip bones as it should Instead it may settle up around the child s abdomen In a crash the belt would apply force on a body area that s unprotected
208. he sun comes out or it becomes cloudy you may need to adjust the HUD brightness again using the dimmer knob Polarized sunglasses could make the HUD image harder to see 3 21 Clean the inside of the windshield as needed to remove any dirt or film that reduces the sharpness or clarity of the HUD image To clean the HUD spray household glass cleaner on a soft clean cloth Wipe the HUD lens gently then dry it Do not spray cleaner directly on the lens because the cleaner could leak into the unit If the ignition is on and you cannot see the HUD image check to see if one of the following has occurred Something is covering the HUD unit The HUD dimmer knob is adjusted properly The HUD image is adjusted to the proper height Ambient light in the direction your vehicle is facing is low A fuse is blown See Fuses and Circuit Breakers on page 5 113 If you ever have to have your windshield replaced be sure to get one that is designed for the HUD or your HUD image may look blurred and out of focus 3 22 Accessory Power Outlets With accessory power outlets you can plug in electrical equipment such as a cellular telephone or CB radio There is a single front power outlet located on the floor console above the climate control system outlets There is one rear power outlet located in the rear of the vehicle on the driver s side To use the outlet pull the cover down When not using it cover the outlet wit
209. he tire although only one side may have the date of manufacture D Maximum Cold Inflation Load Limit oo load that can be fare and the maximum p re needed to support that load See Compac i Spat Tire on page 5 102 and Loading Your Vehiclelon page 4 36 E Tire Inflation The temporary use tire or compact spare tire should be inflated to 60 psi 420 kPa For more information on tire pressure and inflation see Inflation Tire Pressure on page 5 66 F Tire Size A combination of letters and numbers define a tire s width height aspect ratio construction type and service description The letter T as the first character in the tire size means the tire is for temporary use only G Tire Performance Criteria Specification TPC Spec Original equipment tires designed to GM s specific tire performance criteria have a TPC specification code molded onto the sidewall GM s TPC specifications meet or exceed all federal safety guidelines 5 61 Tire Size The following illustration shows an example of a typical passenger car tire size A P Metric Tire The United States version of a metric tire sizing system The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U S Tire and Rim Association 5 62 B Tire Width The three digit number indicates the tire section width in millimeters from sidewall to sidewall C Aspect Ratio
210. he traffic flow Once you are on the freeway adjust your speed to the posted limit or to the prevailing rate if it is slower Stay in the right lane unless you want to pass Before changing lanes check your mirrors Then use your turn signal Just before you leave the lane glance quickly over your shoulder to make sure there is not another vehicle in your blind spot Once you are moving on the freeway make certain you allow a reasonable following distance Expect to move slightly slower at night When you want to leave the freeway move to the proper lane well in advance If you miss your exit do not under any circumstances stop and back up Drive on to the next exit The exit ramp can be curved sometimes quite sharply The exit speed is usually posted Reduce your speed according to your speedometer not to your sense of motion After driving for any distance at higher speeds you may tend to think you are going slower than you actually are Before Leaving on a Long Trip Make sure you are ready Try to be well rested If you must start when you are not fresh such as after a day s work do not plan to make too many miles that first part of the journey Wear comfortable clothing and shoes you can easily drive in Is your vehicle ready for a long trip If you keep it serviced and maintained it is ready to go If it needs service have it done before starting out Of course you will find experienced and
211. hicle in front of you you will not have time to apply your brakes if that vehicle suddenly slows or stops Always leave enough room up ahead to stop even though you have anti lock brakes Using Anti Lock Do not pump the brakes Just hold the brake pedal down firmly and let anti lock work for you You may feel a slight brake pedal pulsation or notice some noise but this is normal Braking in Emergencies At some time nearly every driver gets into a situation that requires hard braking If you have anti lock you can steer and brake at the same time However if you do not have anti lock your first reaction to hit the brake pedal hard and hold it down may be the wrong thing to do Your wheels can stop rolling Once they do the vehicle can not respond to your steering Momentum will carry it in whatever direction it was headed when the wheels stopped rolling That could be off the road into the very thing you were trying to avoid or into traffic If you do not have anti lock use a squeeze braking technique This will give you maximum braking while maintaining steering control You can do this by pushing on the brake pedal with steadily increasing pressure In an emergency you will probably want to squeeze the brakes hard without locking the wheels If you hear or feel the wheels sliding ease off the brake pedal This will help you retain steering control If you do have anti lock it is different See Anti
212. hile you wait However if you are unable to wait Pontiac helps minimize your inconvenience by providing several transportation options Depending on the circumstances your dealer can offer you one of the following Shuttle Service Participating dealers can provide you with shuttle service to get you to your destination with minimal interruption of your daily schedule This includes a one way or round trip shuttle ride to a destination up to 10 miles from the dealership Public Transportation or Fuel Reimbursement If your vehicle requires overnight warranty repairs reimbursement five days maximum may be available for the use of public transportation such as taxi or bus In addition should you arrange transportation through a friend or relative reimbursement for reasonable fuel expenses five day maximum may be available Claim amounts should reflect actual costs and be supported by original receipts Courtesy Rental Vehicle Your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle you obtained if your vehicle is kept for a warranty repair Reimbursement will be limited to a maximum of 30 a day and must be supported by receipts This requires that you sign and complete a rental agreement and meet state local and rental vehicle provider requirements Requirements vary and may include minimum age requirements insurance coverage credit card etc You are responsible for fue
213. hort period of time your receiver may have a fault Consult with your retail location Playing a CD The CD player can play the smaller 8 cm single CDs with an adapter ring Full size CDs and the smaller CDs are loaded in the same manner Unknown If you receive this message when you tune to channel 0 you may have a receiver fault Consult with your dealer increase in skipping difficulty in finding tracks and or difficulty in loading and ejecting If these problems occur try a known good CD Do not add paper labels to CDs they could get caught in the CD player If playing a CD R the sound quality may be reduced due to CD R quality the method of recording the quality of the music that has been recorded and the way the CD R has been handled You may experience an Do not play 3 inch CDs without a standard adapter CD If an error appears on the display see CD Messages later in this section 3 97 LOAD CD amp Press the LOAD side of this button to load CDs into the CD player This CD player will hold up to six CDs To insert one CD do the following 1 Turn the ignition on 2 Press and release the LOAD side of the LOAD CD button 3 Wait for the light located to the right of the slot to turn green 4 Load a CD Insert the CD partway into the slot label side up The player will pull the CD in When a CD is inserted the CD symbol will be displayed If you select an equalization setting for your
214. hrough the options on the display SET This button is used to select and set the options to your preference The DIC will always display the compass reading and the outside temperature If the temperature is below 38 F 3 C the temperature reading will toggle between displaying the temperature and the word ICE for two minutes AVG ECONOMY Average Economy Average fuel economy is viewed as a long term approximation of your overall driving conditions To learn the average fuel economy from a new starting point press and hold the SET button while the average fuel economy is displayed on the DIC The average fuel economy will set to zero INST ECONOMY Instant Economy Instant fuel economy varies with your driving conditions such as acceleration braking and the grade of the road being traveled 3 55 FUEL RANGE The fuel range is an estimated distance that your vehicle can travel on the remaining fuel The fuel economy used to calculate the range is based on your driving history since the last reset of the average speed FUEL USED The fuel used display will show you how much fuel has been used since the last time it was reset To reset the fuel used to zero press and hold the SET button while the fuel used is displayed on the DIC and until the display goes to zero AVG SPEED Average Speed The average speed display will show your average speed from when you first started your vehicle To reset the average speed
215. ht away Service Vehicle Soon Message SERVICE VEHICLE SOON United States Canada This light will come on if your vehicle has certain non emission related problems For example if the entire electrical system fails to send and receive messages from the vehicle s components this message will come on These problems may not be obvious and may affect vehicle performance or durability Consult a qualified dealership for necessary repairs to maintain top vehicle performance Program Mode Message PROGRAM MODE United States Canada If you receive this message your vehicle is in program mode If your vehicle is equipped with the Driver Information Center DIC you are ready to begin programming your vehicle s customization features See DIC Vehicle Personalization on page 3 57 for more information 3 51 Remote Keyless Entry Transmitter Battery Low Warning Message KEY FOB BATTERY 12o LOW United States Canada If you receive this message the battery in the remote keyless entry needs to be replaced See Batter Replacement under Remote Keyless Entry System on page 2 4 for instructions 3 52 Parking Lamp Warning Message PARK LAMP OUT Canada United States If you receive this message one or both of the vehicle s parking lamp bulbs needs replacement See Bulb on page 5 50 for bulb replacement Instructions Driver Information Center DIC DRIVER INFO CENTER
216. ich ever your vehicle has Tighten them hand tight over the wheel nuts using the folding wrench Storing the Flat Tire without the Sliding Rear Convenience Tray D ring D Valve Stem Wing Nut E Full size Tire J hook Flip up the D ring located in the rear cargo area Lay the tire in the rear cargo area of the vehicle with the valve stem up with the center hole of the tire over the D ring For vehicles with aluminum wheels remove the center cap by tapping the back of the cap with the folding wrench my OW gt 5 99 3 Remove the J hook and the wing nut from the back Storing the Flat Tire with the Sliding Rear of the jack access door Assemble the wing nut and Convenience Tray the J hook 4 Install the wing nut and the J hook to the D ring through the center hole of the tire 5 Tighten the wing nut to secure the tire to the floor Push and pull on the tire to make sure the tire is secure and does not move 6 Put back all tools as they were stored in the jack storage compartment Attach the wrench back to the jack Put the jack base on the bracket tab and sit the jack properly between the two ears of the bracket Use the bolt to tighten the jack 7 Put the compartment cover back on slip the tabs on the bottom of the cover into the bottom of the cover opening Push the cover in place and push down the tab on the top of the cover so that it rests in the A D ring E Full size Tire groove This se
217. icle has been sitting for at least three hours or driven no more than 1 mile 1 6 km Remove the valve cap from the tire valve stem Press the tire gage firmly onto the valve to get a pressure measurement If the cold tire inflation pressure matches the recommended pressure on the Tire and Loading Information label no further adjustment is necessary If the inflation pressure is low add air until you reach the recommended amount If you overfill the tire release air by pushing on the metal stem in the center of the tire valve Recheck the tire pressure with the tire gage Be sure to put the valve caps back on the valve stems They help prevent leaks by keeping out dirt and moisture Check Tire Pressure System Your vehicle may have a check tire pressure system that can alert you to a large change in the pressure of one tire The system will not alert you before you drive that a tire is low or flat You must begin driving before the system will work properly The TIRE PRESSURE LOW CHECK TIRES message will appear on the Driver Information Center DIC and the LOW TIRE PRESSURE message will come on the message center if pressure difference or low pressure is detected in one tire In the following conditions the LOW TIRE PRESSURE may not come on even if the tire pressure is low or it may come on when the tire pressure is actually normal if More than one tire is low Only one tire is replaced with a new tire during ser
218. ider or longer than the luggage carrier Notice Damage may be caused to the roof of your vehicle if anything is placed directly on the roof 2 38 Notice Loading cargo on the luggage carrier that weighs more than 220 Ibs 100 kg or hangs over the rear or sides of the vehicle may damage your vehicle Load cargo so that it rests on the slats as far forward as possible and against the side rails making sure to fasten it securely When you carry cargo on the luggage carrier of a proper size and weight put it on the slats and distribute the weight evenly Then slide the crossrail up against the rear of the load to keep it from moving You can then tie it down Cargo containers must be loaded on the crossrails only Don t exceed the maximum vehicle capacity when loading your vehicle For more information on vehicle capacity and loading see Loading Your Vehicle on page 4 36 To prevent damage or loss of cargo as you re driving check now and then to make sure the luggage carrier and cargo are still securely fastened Loading things onto the luggage carrier can interfere with the performance of your XM Satellite Radio System Your luggage carrier has release levers within the end of each crossrail support 2 39 To adjust the crossrail s the sunroof stop A must be removed To remove the sunroof stop do the following 1 Find the tool B located in a bag in the glovebox labeled tool kit acsry
219. il LOCK FEEDBACK appears on the DIC 3 Press the SET button until the arrow is before OFF LIGHTS or HORN The mode you selected is now set You can now exit programming mode by following the instructions next in this section Exiting Programming Mode To exit programming mode do one of the following Shift out of PARK P Turn the ignition key out of ON Do not program any commands for one minute while in the programming mode The programming mode message will turn off to let you know that you are no longer in the programming mode Once you have reached the end of the personalization features PERSONALIZATION SELECTION IS DONE will appear briefly Then PRESS SET TO EXIT MODE TO CONTINUE will appear Pressing SET will exit you out of the DIC Pressing MODE will take you to the beginning of personalization 3 63 Audio System s Notice Before you add any sound equipment to your vehicle like a tape player CB radio mobile telephone or two way radio be sure you can add what you want If you can it s very important to do it properly Added sound equipment may interfere with the operation of your vehicle s engine radio or other systems and even damage them Your vehicle s systems may interfere with the operation of sound equipment that has been added improperly So before adding sound equipment check with your dealer and be sure to check federal rules covering mobile radio and telephone units You
220. ilt the latch plate and keyhole on the lap belt buckle as shown Be sure to pull it along the belt slide the shoulder belt part into the keyhole until it locks into place To make the belt shorter pull its free end as shown until the belt is snug 4 Buckle position and release the lap shoulder belt the same way as the other lap shoulder belts If the belt isn t long enough see Safety Belj on page 1 38 Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to 1 34 Rear Safety Belt Comfort Guides for Children and Small Adults Rear safety belt comfort guides will provide added safety belt comfort for older children who have outgrown booster seats and for small adults When installed on a shoulder belt the comfort guide better positions the belt away from the neck and head There is one guide available for each passenger position in the second row rear seat To provide added safety belt comfort for children who have outgrown child restraints and booster seats and for smaller adults the comfort guides may be installed on the shoulder belts Here s how to install a comfort guide and use the safety belt 2 Place the guide over the belt and insert the two edges of the belt into the slots of the guide Second Row Outside Positions For second row outside positions do the following 1 Remove the guide from its storage clip located on
221. image as a parking aid you may misjudge the distance and damage your vehicle Do not use the HUD image as a parking aid The HUD controls are located to the right of the instrument panel cluster When the HUD is on the speedometer reading will be displayed continually The current audio system information will only be displayed for three seconds after the radio tape or CD track status changes This will happen whenever one of the radio controls is pressed either on the radio or on the optional steering wheel controls To adjust the HUD so you can see it properly do the following 1 Start your engine and turn the dimmer knob to the desired HUD image brightness The brightness of the HUD image is determined by the ambient light conditions in the direction your vehicle is facing and where you have the HUD dimmer knob set If you are facing a dark object or a heavily shaded area your HUD may anticipate that you are entering a dark area and may begin to dim 2 Adjust the driver s seat If you change your seat position you may have to readjust your HUD 3 Press the UP or DN buttons until the HUD image is easy to see then press the DN button until the HUD image is as low as possible The HUD image should remain in full view straight ahead near the front bumper The HUD image can only be adjusted up and down not side to side 4 To turn the image off turn the dimmer knob counterclockwise to the OFF position If t
222. in to stop scanning RCL Recall Push this knob to see how long the current track has been playing To change the default on the display track and elapsed time push the knob until you see the display you want then hold the knob until the display flashes The selected display will now be the default While elapsed time is showing CD TIME will appear on the display BAND Press this button to listen to the radio when a CD is playing The inactive CD will remain safely inside the radio for future listening CD AUX Auxiliary Press this button to play a CD when listening to the radio The CD symbol will appear on the display when a CD is loaded 3 74 A Eject Press this button to eject a CD Eject may be activated with either the ignition or radio off CDs may be loaded with the radio and ignition off if this button is pressed first CD Messages CHECK CD If this message appears on the radio display and the CD comes out it could be for one of the following reasons e Itis very hot When the temperature returns to normal the CD should play e You are driving on a very rough road When the road becomes smoother the CD should play e The CD is dirty scratched wet or upside down The air is very humid If so wait about an hour and try again There may have been a problem while burning the CD The label may be caught in the CD player If the CD is not playing correctly for any other reason try a known g
223. ine parts and start a fire These include liquids like fuel oil coolant brake fluid windshield washer and other fluids and plastic or rubber You or others could be burned Be careful not to drop or spill things that will burn onto a hot engine Hood Release To open the hood do the following 1 Pull the hood release handle located under the instrument panel on the driver s side of the vehicle 2 At the front of the vehicle pull up on the center of the hood and push the secondary hood release to the right 3 Lift the hood 4 Pull forward on the hood prop to release it from its storage clip 5 Put the end of the hood prop into the slot in the underside of the hood Before closing the hood be sure all filler caps are on properly To close the hood do the following 1 Lift the hood to relieve pressure on the hood prop 2 Remove the hood prop from the slot in the hood 3 Return the hood prop to its storage clip 4 Let the hood down and close it firmly Engine Compartment Overview When you lift the hood you ll see these items A Underhood Fuse Block See B on page 5 113 Remote Positive Terminal See Jump Starting on page 5 42 C Power Steering Fluid Reservoir See D on page 5 35 Automatic Transaxle Fluid Dipstick See Automatid Transaxle Fluid on page 5 20 Brake Master Cylinder See Brakes on page 5 38 F Windshield Washer Fluid Reservoir See Wi
224. iner W 1 1 5 9 Filling Your Tank scscccc ea henleder 5 7 Fuels in Foreign Countries eeeeeeeeee ee 5 6 GAG ERE E EE TT 3 42 Fuel cont Gasoline Octane W u sssseeeeeereren eee eeeeee een ees 5 4 Gasoline Specifications ceeeeeeeeeeee eee ees 5 5 Low Warning Message ccecce 3 50 Fuses Fuses and Circuit Breakers 5 113 Windshield Wiper sccssns c tictcactescsencmemeteesveane 5 112 Gage Engine Coolant Temperature 1 3 39 Fuel pei ecdoslets idcaiseovsiataniaaeeeceieiies E 3 42 Speedometer cceeeceeeeeeeeeeeeaeeeeeaeeeeeaes 3 33 Tachometer wie or vorde se iia ane iaiia 3 34 Garage Door Opener Compartment 1 1 2 34 Gasoline OClANG e reen 5 4 Specifications ssssesseeeerreeen ennen renerne 5 5 GIOVE BOX rusker enade nen R iee aae 2 34 GM Mobility Program for Persons With DISADINNGS ssirisirininiiaiansip nrinn 7 6 Hatch Ajar Warning Message secc 3 48 Hazard Warning Flashers seeen 3 6 Head Restraints ccceeceeeeeeeneeeeeeeeeeeeeeeeeees 1 5 Headlamp Exit Delay eee 3 16 3 58 Headlamp High Low Beam Changer 3 9 Headlamp Wiring 2 ceeceeeeeeeeeeereeeeeeeeeees 5 112 Headlamps earrannan E E 5 51 Bulb Replacement 213222 ser bure i bios LUS EEG 5 50 Front Turn Signal Sidemarker and Parking Lamps 23 ee E N 5 53 Halogen BUDS 3 isccissccanainanatenctenheanencantadensaenye
225. iness light on the instrument panel which shows the air bag symbol The system checks the air bag s electrical system for malfunctions The light tells you if there is an electrical problem The system check includes the air bag sensor the air bag modules the wiring and the diagnostic module For more information on the air bag system see on page 1 67 This light will come on when you start your vehicle and it will flash for a few seconds Then the light should go out This means the system is ready 3 35 If the air bag readiness light stays on after you start the vehicle or comes on when you are driving your air bag system may not work properly Have your vehicle serviced right away If the air bag readiness light stays on after you start your vehicle it means the air bag system may not be working properly The air bags in your vehicle may not inflate in a crash or they could even inflate without a crash To help avoid injury to yourself or others have your vehicle serviced right away if the air bag readiness light stays on after you start your vehicle The air bag readiness light should flash for a few seconds when you turn the ignition key to ON If the light doesn t come on then have it fixed so it will be ready to warn you if there is a problem 3 36 Brake System Warning Light When the ignition is on the brake system warning light will come on when you set your parking brake The light will sta
226. ing a seat belt In addition avoiding excessive speed sudden or abrupt turns and drunken or aggressive driving can help make trips safer and avoid the possibility of a crash especially a rollover crash This section provides many useful tips to help you drive more safely Driving Environment You can also help avoid a rollover or other type of crash by being prepared for driving in inclement weather at night or during other times where visibility or traction may be limited such as on curves slippery roads or hilly terrain Unfamiliar surroundings can also have hidden hazards To help you learn more about driving in different conditions this section contains information about city freeway and off road driving as well as other hints for driving in various weather conditions Vehicle Design According to the U S Department of Transportation utility vehicles have a significantly higher rollover rate than other types of vehicles Utility vehicles do have higher ground clearance and a narrower track or shorter wheelbase than passenger cars to make them more capable for off road driving Specific design characteristics like these give the driver a better view of the road but also give utility vehicles a higher center of gravity than other types of vehicles This means that you should not expect a utility vehicle to handle the same way a vehicle with a lower center of gravity like a car would in similar situations But driv
227. ing the INFO button You can view an old message until a new message is received or a different station is tuned to 3 70 TRAF Traffic If TRAF appears on the display the tuned station broadcasts traffic announcements To receive the traffic announcement from the tuned station press this button Brackets will be displayed around TRAF and when a traffic announcement comes on the tuned radio station you will hear it If the current tuned station does not broadcast traffic announcements press the TRAF button and the radio will seek to a station that does When the radio finds a station that broadcasts traffic announcements the radio will stop and brackets will be displayed around TRAF When a traffic announcement comes on the tuned radio station you will hear it If no station is found NO TRAFFIC will appear on the display If the brackets are on the display and TRAF is not you can then press the TRAF button to remove the brackets or use the TUNE knob or the SEEK arrows to go toa station that supports traffic announcements If no station is found NO TRAFFIC will appear on the display Your radio will play a traffic announcement if the volume is low Your radio will interrupt the play of a CD if the last tuned station broadcasts traffic announcements and the brackets are displayed This function does not apply to XM Satellite Radio Service Radio Messages CALIBRATE Your audio system has been calibrated for your vehicle
228. ion You should probably stay with your vehicle unless you know for sure that you are near help and you can hike through the snow Here are some things to do to summon help and keep yourself and your passengers safe Turn on your hazard flashers e Tie a red cloth to your vehicle to alert police that you have been stopped by the snow 4 31 You can run the engine to keep warm but be careful Snow can trap exhaust gases under your vehicle This can cause deadly CO carbon monoxide gas to get inside CO could overcome you and kill you You can not see it or smell it so you might not know it is in your vehicle Clear away snow from around the base of your vehicle especially any that is blocking your exhaust pipe And check around again from time to time to be sure snow does not collect there Open a window just a little on the side of the vehicle that is away from the wind This will help keep CO out 4 32 Run your engine only as long as you must This saves fuel When you run the engine make it go a little faster than just idle That is push the accelerator slightly This uses less fuel for the heat that you get and it keeps the battery charged You will need a well charged battery to restart the vehicle and possibly for signaling later on with your headlamps Let the heater run for a while Then shut the engine off and close the window almost all the way to preserve the heat Start the engine again and
229. ion on page 1 54 for more on this including important safety information Once you have the top strap anchored you ll be ready to secure the child restraint itself Tighten the top strap when and as the child restraint manufacturer s instructions say 1 50 Top Strap Anchor Location Your vehicle has top strap anchors already installed for the rear seating positions An anchor bar for a top strap is located at the rear of the seat cushion for each second row outboard seating position and the anchor bar for the center position bench seat is located on the floor behind the second row seats If your vehicle has the sliding rear convenience tray you need to remove a plastic plug and look under the convenience tray to find the anchor bar for the center position for the bench seat Do not use a child restraint with a top strap in the right front passenger s position because there is no place to anchor the top strap i E 17 h I i k DRE i wile eile Lower Anchorages and Top Tethers for Children LATCH System Your vehicle has the LATCH system You will find anchors A in both rear seat outside passenger positions This system designed to make installation of child restraints easier does not use the vehicle s safety belts Instead it uses vehicle anchors A B and child restraint attachments to secure the restraints Some restraints also use another vehicle anchor to secure a top tethe
230. ional keys only If all the currently programmed keys are lost or do not operate you must see your dealer or a locksmith who can service PASS Key III to have keys made and programmed to the system See your dealer who can service PASS Key III to get a new key blank that is a cut exactly as the ignition key that operates the system Canadian Owners If you lose or damage your keys only a GM dealer can service PASS Key III to have new keys made To program additional keys you will need two current driver s keys black in color You must add a step to the following procedure After Step 3 repeat Steps 1 through 3 with the second current driver s key Then continue with Step 4 To program the new PK3 key do the following 1 Verify the new key has PK3 stamped on it 2 Insert the current driver s key in the ignition and start the engine If the engine will not start see your dealer for service 3 After the engine has started turn the key to OFF and remove the key 4 Insert the key to be programmed and turn it to ON within 10 seconds of removing the previous key 5 The SECURITY message will turn off once the key has been programmed It may not be apparent that the SECURITY message went on due to how quickly the key is programmed 6 Repeat Steps 1 through 4 if additional keys are to be programmed If you are ever driving and the SECURITY message comes on and stays on you will be able to restart your engine if
231. irculation and runs the air conditioning compressor unless the outside temperature is at or below freezing The recirculation mode cannot be selected while in the defog mode W Defrost This mode directs most of the air to the windshield and the side window outlets with some air directed to the floor outlets In this mode the system will automatically turn off recirculation and run the air conditioning compressor unless the outside temperature is at or below freezing Recirculation cannot be selected while in the defrost mode Do not drive the vehicle until all the windows are clear Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window GW REAR Press this button to turn the rear window defogger on or off An indicator light in the button will come on to let you know that the rear window defogger is activated The rear window defogger will turn off approximately 10 minutes after the button is pressed If turned on again the defogger will only run for approximately five minutes before turning off The defogger can also be turned off by pressing the button again or by turning off the engine Notice Don t use anything sharp on the inside of the rear window If you do you could cut or damage the warming grid and the repairs wouldn t be covered by your warranty Do not attach a temporary vehicle license tape a decal or anything similar to the defogger grid 3 29 Ou
232. is 0 04 percent The BAC will be over 0 10 percent after three to six drinks in one hour Of course as we have seen it depends on how much alcohol is in the drinks and how quickly the person drinks them But the ability to drive is affected well below a BAC of 0 10 percent Research shows that the driving skills of many people are impaired at a BAC approaching 0 05 percent and that the effects are worse at night All drivers are impaired at BAC levels above 0 05 percent Statistics show that the chance of being in a collision increases sharply for drivers who have a BAC of 0 05 percent or above A driver with a BAC level of 0 06 percent has doubled his or her chance of having a collision At a BAC level of 0 10 percent the chance of this driver having a collision is 12 times greater at a level of 0 15 percent the chance is 25 times greater The body takes about an hour to rid itself of the alcohol in one drink No amount of coffee or number of cold showers will speed that up I will be careful is not the right answer What if there is an emergency a need to take sudden action as when a child darts into the street A person with even a moderate BAC might not be able to react quickly enough to avoid the collision There is something else about drinking and driving that many people do not know Medical research shows that alcohol in a person s system can make crash injuries worse especially injuries to the brain spinal
233. is broken or melted replace the fuse Be sure you replace a bad fuse with a new one of the identical size and rating If you ever have a problem on the road and don t have a spare fuse you can borrow one that has the same amperage Just pick a feature of your vehicle that you can get along without like the radio or cigarette lighter and use its fuse if it is the right amperage Replace it as soon as you can There are two fuse blocks in your vehicle the floor console fuse block and the underhood fuse block Floor Console Fuse Block The floor console fuse block is located to the right of the shift lever The fuses marked spare are available if a replacement fuse is needed Pull the door open to access the fuse block 5 113 Steering Wheel Radio Controls Power Door Locks 12 Electronic Level Control ELC Compressor Liftgate and Endgate Rear Auxiliary Power Outlet Electronic Level Control ELC 15 Compressor Relay and Height Sensor Heated Mirrors Power Mirrors gnition 1 Module Turn Signal Switch Rear Defogger Air Bag Module TCC Switch Climate Control Blower Motor Climate Control Mode and Temperature Motors and Head Up Display Empty Windshield Wipers and Washer Instrument Panel Cluster Body Control Module BCM PASS Key III Park Lock Ignition Key Solenoid wo w DID ye MININ SD Co O RN Map Lamps Courtesy Lamps and Instrument Panel Lights
234. issin 2 42 Console Cooler cceeeeeeeeeneeeeeeeeeeeeeeeeeees 2 36 Convenience Net ceeeceeeeeeeeeeeeeeee eens 2 41 Cupholder S ccseceeeeeeeeeeeeeeeeeeeeeeeeeeees 2 34 Front Door Utility Packs usus sled slebne 2 36 Storage Areas cont GIOVE BOX enee rnida onen ende reed 2 34 Overhead Console 222 ad nesini aeciaii as 2 34 Rear Storage Area W u sssseeeeeereerere renerne 2 37 Roof Rack System ceeceeeeeeeeeeeeeeee tented 2 38 Sliding Rear Convenience Tray 06 2 43 Storage Compartment ceeeeeeeeeeeeeeeeeee tenes 2 36 Storing a Flat or Spare Tire and Tools 5 97 Stuck in Sand Mud Ice or Snow 0065 4 33 SUN VISOMS e E a tiled E Mallia ER L 2 13 Sunglasses Storage Compartment 00 2 36 SUNMOOP s c Secsrecccnaadindacedsacersaencehimnsaginuseaater ec 2 48 Switchbanks Instrument Panel 0 000 3 19 Tachometer fiiinccasiichiac odidectaidiadnieremaladdeess ikaets 3 34 Tallgate Liftgate stab renee dade ae 2 10 Taillamps Stoplamps and Back Up Lamps 00 5 54 TCS Warning Light eceeeceeeeeeeeeee eee ees 3 38 Theft Deterrent Radio cccee eee eeeeeeeeees 3 116 Theft Deterrent Systems ceeeeeeeee eee eee ees 2 14 Content Theft Deterrent eeeeeeeeee eee eeeee 2 14 PASS Key M racs ienis nierien 2 16 PASS Key III Operatio
235. ith this You can be seriously injured by a twisted belt In a crash you wouldn t have the full width of the belt to spread impact forces If a belt is twisted make it straight so it can work properly or ask your dealer to fix it A The belt is twisted across the body Safety Belt Use During Pregnancy Safety belts work for everyone including pregnant women Like all occupants they are more likely to be seriously injured if they don t wear safety belts To unlatch the belt just push the button on the buckle The belt should go back out of the way Before you close the door be sure the belt is out of the way If you slam the door on it you can damage both the belt and your vehicle 1 26 A pregnant woman should wear a lap shoulder belt and the lap portion should be worn as low as possible below the rounding throughout the pregnancy The best way to protect the fetus is to protect the mother When a safety belt is worn properly it s more likely that the fetus won t be hurt in a crash For pregnant women as for anyone the key to making safety belts effective is wearing them properly Right Front Passenger Position To learn how to wear the right front passenger s safety belt properly see Driver Position on page 1 18 The right front passenger s safety belt works the same way as the driver s safety belt except for one thing If the belt stops before it reaches the buckle tilt the l
236. ive proper endurance handling speed rating load range traction ride and other things during normal service on your vehicle If your tires have an all season tread design the TPC number will be followed by an MS for mud and snow If you ever replace your tires with those not having a TPC Spec number make sure they are the same size load range speed rating and construction type bias bias belted or radial as your original tires Mixing tires could cause you to lose control while driving If you mix tires of different sizes or types radial and bias belted tires the vehicle may not handle properly and you could have a crash Using tires of different sizes may also cause damage to your vehicle Be sure to use the same size and type tires on all wheels It s all right to drive with your compact spare temporarily it was developed for use on your vehicle See Compact Spare Tire in the index If you use bias ply tires on your vehicle the wheel rim flanges could develop cracks after many miles of driving A tire and or wheel could fail suddenly causing a crash Use only radial ply tires with the wheels on your vehicle 5 71 Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width For example Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States N
237. ize Be aware that there are special things to know about safety belts and children And there are different rules for smaller children and babies If a child will be riding in your vehicle see on page 1 39 or infants and Young Children on page 17 41 Follow those rules for everyone s protection First you ll want to know which restraint systems your vehicle has We ll start with the driver position Driver Position This part describes the driver s restraint system Lap Shoulder Belt The driver has a lap shoulder belt Here is how to wear it properly 1 Close and lock the door 2 Adjust the seat so you can sit up straight To see how see Seats in the Index Pick up the latch plate and pull the belt across you Do not let it get twisted The shoulder belt may lock if you pull the belt across you very quickly If this happens let the belt go back slightly to unlock it Then pull the belt across you more slowly 4 Push the latch plate into the buckle until it clicks Pull up on the latch plate to make sure it is secure If the belt is not long enough see Safety Belj on page 1 38 Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to 5 To make the lap part tight pull down on the buckle end of the belt as you pull up on the shoulder belt NAG Ss 4 The lap part of the belt should b
238. jects Do not shift into a drive gear while your engine is running at high speed Notice Shifting out of PARK P or NEUTRAL N with the engine racing may damage the transaxle The repairs would not be covered by your warranty Be sure the engine is not racing when shifting your vehicle AUTOMATIC OVERDRIVE D This position is for normal driving If you need more power for passing and you are Going less than 35 mph 55 km h push your accelerator pedal about halfway down Going about 35 mph 55 km h or more push the accelerator all the way down You will shift down to the next gear and have more power Notice Driving your vehicle if you notice that it is moving slowly or not shifting gears as you increase speed may damage the transaxle Have your vehicle serviced right away You can drive in SECOND 2 when you are driving less than 35 mph 55 km h and AUTOMATIC OVERDRIVE D for higher speeds until then 2 23 Warm Up Shift Your vehicle has a computer controlled transaxle designed to warm up the engine faster when the outside temperature is 35 F 2 C or colder You may notice that the transaxle will shift at a higher vehicle speed until the engine is warmed up This is a normal condition designed to provide heat to the passenger compartment and defrost the windows more quickly THIRD 3 This position is also used for normal driving but it offers more power and lower fuel economy than AUTOMATIC OVE
239. just the instrument panel brightness Press the knob in when not in use Interior Lamps Control Turn the interior lamp control to one of the following positions OFF This position turns the interior lamps off DOOR This position turns on the interior lamps when any door is opened and when the ignition key is removed from the ignition ON This position turns the interior lamps on Headlamp Exit Delay The headlamp exit delay feature will keep the headlamps and parking lamps on at night for 30 seconds if the following conditions are met The ignition is turned to OFF The exterior lamp control is in the AUTO position e It is dark enough outside After 30 seconds the headlamps and parking lamps will turn off The lamps will turn off before the 30 seconds if one of the following occurs The ignition is turned to ON The exterior lamp control is turned out of the AUTO position If you would like to program the headlamp exit delay feature and your vehicle is equipped with the Driver Information Center DIC see DIC Vehicle Personalzator rsonalization on page 3 57 Entry Lighting With entry lighting the interior of your vehicle will illuminate for 25 seconds so you can see inside your vehicle before you enter To activate entry lighting do one of the following Unlock a door using the key when the interior lamp control is in the DOOR position and the ignition is OFF Press UNLOCK on the remote ke
240. ke a hard stop on a slippery road Whether you have the anti lock braking system or not you will want to begin stopping sooner than you would on dry pavement Without anti lock brakes if you feel your vehicle begin to slide let up on the brakes a little Push the brake pedal down steadily to get the most traction you can 4 30 Remember unless you have anti lock if you brake so hard that your wheels stop rolling you will just slide Brake so your wheels always keep rolling and you can still steer e Whatever your braking system allow greater following distance on any slippery road Watch for slippery spots The road might be fine until you hit a spot that is covered with ice On an otherwise clear road ice patches may appear in shaded areas where the sun can not reach around clumps of trees behind buildings or under bridges Sometimes the surface of a curve or an overpass may remain icy when the surrounding roads are clear If you see a patch of ice ahead of you brake before you are on it Try not to brake while you are actually on the ice and avoid sudden steering maneuvers If You Are Caught in a Blizzard Put on extra clothing or wrap a blanket around you If you have no blankets or extra clothing make body insulators from newspapers burlap bags rags floor mats anything you can wrap around yourself or tuck under your clothing to keep warm If you are stopped by heavy snow you could be in a serious situat
241. l the battery is weak if the KEY FOB BATTERY LOW message appears in the message center If you get this message the battery in the key fob needs to be replaced Notice When replacing the battery use care not to touch any of the circuitry Static from your body transferred to these surfaces may damage the transmitter Insert a flat object such as a coin into the slot on the side of the transmitter and twist to separate the halves Gently pry the battery out of the transmitter Do not use the metal flanges to pop out the battery Replace the battery Reassemble the transmitter Make sure the halves are snapped together tightly so water will not get in Press and hold the LOCK and UNLOCK buttons for seven seconds to synchronize the transmitter Check the transmitter operation Doors and Locks There are several ways to lock and unlock your vehicle From the outside use your key or the remote keyless entry transmitter Door Locks To unlock the driver s door from the outside with the key insert the key and turn it toward the front of the vehicle To lock the driver s door from the outside A CAUTION with your key insert the key and turn it toward the rear of the vehicle Unlocked doors can be dangerous e Passengers especially children can easily open the doors and fall out of a moving vehicle When a door is locked the handle will not open it You increase the chance of being thrown out of
242. l usage charges and may also be responsible for taxes levies usage fees excessive mileage or rental usage beyond the completion of the repair Generally it is not possible to provide a like vehicle as a courtesy rental Additional Program Information Courtesy Transportation is available during the Bumper to Bumper warranty coverage period but it is not part of the New Vehicle Limited Warranty A separate booklet entitled Warranty and Owner Assistance Information furnished with each new vehicle provides detailed warranty coverage information Courtesy Transportation is available only at participating dealers and all program options such as shuttle service may not be available at every dealer Please contact your dealer for specific information about availability All Courtesy Transportation arrangements will be administered by appropriate dealer personnel Canadian Vehicles For warranty repairs during the Complete Vehicle Coverage period of the General Motors of Canada New Vehicle Limited warranty alternative transportation may be available under the Courtesy Transportation Program Please consult your dealer for details General Motors reserves the right to unilaterally modify change or discontinue Courtesy Transportation at any time and to resolve all questions of claim eligibility pursuant to terms and conditions described herein at its sole discretion Vehicle Data Collection and Event Data Records Your vehicl
243. lastic and rubber parts That damage would not be covered under your warranty Some gasolines that are not reformulated for low emissions may contain an octane enhancing additive called methylcyclopentadienyl manganese tricarbonyl MMT ask the attendant where you buy gasoline whether the fuel contains MMT General Motors does not recommend the use of such gasolines Fuels containing MMT can reduce the life of spark plugs and the performance of the emission control system may be affected The malfunction indicator lamp may turn on If this occurs return to your authorized GM dealer for service Fuels in Foreign Countries If you plan on driving in another country outside the United States or Canada the proper fuel may be hard to find Never use leaded gasoline or any other fuel not recommended in the previous text on fuel Costly repairs caused by use of improper fuel would not be covered by your warranty To check the fuel availability ask an auto club or contact a major oil company that does business in the country where you will be driving Filling Your Tank Fuel vapor burns violently and a fuel fire can cause bad injuries To help avoid injuries to you and others read and follow all the instructions on the pump island Turn off your engine when you are refueling Do not smoke if you are near fuel or refueling your vehicle Keep sparks flames and smoking materials away from fuel Do not leave the fuel pump unattended when
244. lator With it you can inflate things like air mattresses and basketballs and you can also use it to bring your tires up to the proper pressure The accessory inflator is located in the rear compartment on the driver s side To remove the cover pull the tab on the cover and pull it off This is the symbol on the accessory inflator switch There may be an accessory inflator kit stored in the glove box It includes a 20 foot 6 m hose with an air pressure gage and nozzle adapters 5 76 Inflating something too much can make it explode and you or others could be injured Be sure to read the inflator instructions and inflate any object only to its recommended pressure To use your accessory inflator system do the following 1 Turn the ignition to ACCESSORY or ON 2 Attach the appropriate nozzle adapter if required to the end of the hose that has the pressure gage 3 Attach that end of the hose to the object you wish to inflate 4 Remove the protective cap covering the outlet 5 Attach the other end of the hose to the outlet 6 Press the accessory inflator switch The light in the switch will come on to show the system is working lf the accessory inflator system does not turn on or the light does not come on the fuse may be blown or installed incorrectly See Fuses and Circuit Breakers on page 5 113 or see your dealer for service Your accessory inflator will automatically shut off after about 10 min
245. lder belt but the child is so small that the shoulder belt is very close to the child s face or neck A If the child is sitting in a seat next to a window move the child toward the center of the vehicle If the child is sitting in the center rear seat passenger position move the child toward the safety belt buckle In either case be sure that the shoulder belt still is on the child s shoulder so that in a crash the child s upper body would have the restraint that belts provide If the child is sitting in a rear seat see Belt Comfort Guides for Children and Smal 1 40 Never do this Here a child is sitting in a seat that has a lap shoulder belt but the shoulder part is behind the child If the child wears the belt in this way in a crash the child might slide under the belt The belt s force would then be applied right on the child s abdomen That could cause serious or fatal injuries The lap portion of the belt should be worn low and snug on the hips just touching the child s thighs This applies belt force to the child s pelvic bones in a crash Infants and Young Children Everyone in a vehicle needs protection This includes infants and all other children Neither the distance traveled nor the age and size of the traveler changes the need for everyone to use safety restraints In fact the law in every state in the United States and in every Canadian province says children up to some age
246. le any door is open Instead three chimes will be heard to indicate that the delayed locking feature is in operation Five seconds after all doors are closed the doors will lock automatically If the ignition is in ON or ACCESSORY this feature will not lock the doors If your vehicle is equipped with the Driver Information Center DIC see DIC Vehicle Personalization on page 3 57 to program the delayed locking feature Programmable Automatic Door Locks All of the doors will automatically lock when all doors are closed the engine is running and the shift lever is shifted out of PARK P All of the doors will automatically unlock when the shift lever is shifted into PARK P With the automatic door lock feature you can still lock or unlock the doors at any time either manually with the power door lock switches or by pressing LOCK on the remote keyless entry transmitter See Remote Keyless on page 2 4 for TOTS information If your vehicle is equipped with the Driver Information Center DIC see DIC Vehicle Personalization on page 3 57 to program the automatic door lock feature Rear Door Security Locks Your vehicle is equipped with rear door security locks that help prevent passengers from opening the rear doors on your vehicle from the inside To use one of these locks do the following 1 Open one of the rear doors 2 On the inside of the rear door will be a lock Push the lever up to engage the
247. le to overheat Be sure to get an accurate reading if you check the transaxle fluid Wait at least 30 minutes before checking the transaxle fluid level if you have been driving e When outside temperatures are above 90 F 32 C At high speed for quite a while In heavy traffic especially in hot weather To get the right reading the fluid should be at normal operating temperature which is 180 F to 200 F 82 C to 93 C Get the vehicle warmed up by driving about 15 miles 24 km when outside temperatures are above 50 F 10 C If it is colder than 50 F 10 C you may have to drive longer Checking the Fluid Level To prepare your vehicle do the following 1 Park your vehicle on a level place and keep the engine running 2 With the parking brake applied place the shift lever in PARK P 3 With your foot on the brake pedal move the shift lever through each gear range pausing for about three seconds in each range Then position the shift lever in PARK P 4 Let the engine run at idle for three to five minutes Then without shutting off the engine do the following The dipstick is located toward the back of the engine compartment next to the brake master cylinder The dipstick handle is a bright red loop See Engine Compartment Overview on page 5 12 for more Information on location 1 Pull out the dipstick and wipe it with a clean rag or paper towel 2 Push it back in all the way wait three
248. let it go back all the way The safety belt will move freely again and be ready to work for an adult or larger child passenger Air Bag Systems This part explains the frontal and side impact air bag systems Your vehicle has air bags a frontal air bag for the driver and another frontal air bag for the right front passenger Your vehicle may also have a side impact air bag Side impact air bags are available for the driver and right front passenger If your vehicle has a side impact air bag for the driver and or the right front passenger the words AIR BAG will appear on the air bag covering on the side of the seatback closest to the door 1 61 Frontal air bags are designed to help reduce the risk of injury from the force of an inflating frontal air bag But these air bags must inflate very quickly to do their job and comply with federal regulations Here are the most important things to know about the air bag systems You can be severely injured or killed in a crash if you aren t wearing your safety belt even if you have air bags Wearing your safety belt during a crash helps reduce your chance of hitting things inside the vehicle or being ejected from it Air bags are designed to work with safety belts but don t replace them Frontal air bags for the driver and right front passenger are designed to deploy only in moderate to severe frontal and near frontal CAUTION Continued 1 62 crashes They aren
249. level can cause damage to your engine not covered by your warranty Engine Coolant Level Check Check the engine coolant level and add DEX COOL coolant mixture if necessary See Engine Coolant oolani on page 5 22 for further details Windshield Washer Fluid Level Check Check the windshield washer fluid level in the windshield washer tank and add the proper fluid if necessary At Least Once a Month Tire Inflation Check Visually inspect your tires and make sure tires are inflated to the correct pressures Don t forget to check your spare tire See ies on page 5 58 for further details Check to make sure the spare tire is stored securely Push pull and then try to rotate_or turn the spare tire If it moves tighten it See Changing a Flat Tir t Tire on page 5 78 At Least Once a Year Starter Switch Check When you are doing this inspection the vehicle could move suddenly If the vehicle moves you or others could be injured 1 Before you start be sure you have enough room around the vehicle 2 Firmly apply both the parking brake and the regular brake See Parking Brake on page 2 25 if necessary Do not use the accelerator pedal and be ready to turn off the engine immediately if it starts 3 Try to start the engine in each gear The starter should work only in PARK P or NEUTRAL N If the starter works in any other position contact your GM Goodwrench dealer for service Automatic Transaxle Shi
250. lk and children s programming XM provides digital quality audio and text information including song title and artist name A service fee is required in order to receive the XM service For more information contact XM at www xmradio com or call 1 800 852 XMXM 9696 3 75 Playing the Radio PWR Power Push this knob to turn the system on and off VOL Volume Turn this knob to increase or to decrease volume SCV Speed Compensated Volume With SCV your audio system adjusts automatically to make up for road and wind noise as you drive Set the volume at the desired level Press this button to select MIN MED or MAX Each higher setting allows for more volume compensation at faster vehicle speeds Then as you drive SCV automatically increases the volume as necessary to overcome noise at any speed The volume level should always sound the same to you as you drive If you don t want to use SCV select OFF RCL Recall Push this knob to switch the display between the radio station frequency and the time Pushing this knob with the ignition off will display the time For XM 48 contiguous US states if equipped push the RCL knob while in XM mode to retrieve four different categories of information related to the current song or channel Artist Song Title Category or PTY Channel Number Channel Name To change the default on the display push the RCL knob until you see the display you want then h
251. ll doors will unlock with every press of UNLOCK on the remote entry transmitter 3 61 Your vehicle was originally programmed to ALL The mode may have been changed since then To determine the current mode or to change the mode do the following 1 Follow the instructions for Entering Programming Mode listed previously 2 Press the MODE button until REMOTE DOOR UNLOCK appears on the DIC 3 Press the SET button until the arrow is before DRIVER ALL or ALL The mode you selected is now set You can either exit programming mode by following the instructions later in this section or program the next feature available on your vehicle Unlock Feedback The unlock feedback feature can be programmed to one of the following modes LIGHTS This mode does the following During the day when the ignition is in OFF and UNLOCK on the remote keyless entry transmitter is pressed the headlamps and parking lamps will flash During the night when the ignition is in OFF the headlamps and parking lamps will be activated for 30 seconds when UNLOCK is pressed on the 3 62 remote keyless entry transmitter If you would like to change the amount of time the lamps stay on change the headlamp exit delay feature OFF The headlamps and parking lamps will not flash when UNLOCK is pressed on the remote keyless entry transmitter Your vehicle was originally programmed to LIGHTS The mode may have been changed since then To d
252. ll not attach to the rear set of floor pins 1 Squeeze the angled latch release bar toward the straight crossbar while placing the front hooks of the bench seat onto the front two floor pins Firmly push the rear hooks onto the rear floor pins by pushing down on the rear of the seat Try to raise the seat to check that it is locked down Lift the seatback recliner lever and raise the seatback until it locks upright Push and pull on the seatback to check that it is locked upright Attach the lap belt Safety Belts Safety Belts They Are for Everyone This part of the manual tells you how to use safety belts properly It also tells you some things you should not do with safety belts It is extremely dangerous to ride in a cargo area inside or outside of a vehicle In a collision people riding in these areas are more likely to be seriously injured or killed Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts Be sure everyone in your vehicle is in a i seat and using a safety belt properly Don t let anyone ride where he or she can t wear a safety belt properly If you are in a crash and you re not wearing a safety belt your injuries can be much worse You can hit Your vehicle has a light that comes on as a reminder to buckle up See Safety Belt Reminde Lighiton page 3 35 In most states and in all Canadian provinces the law says to we
253. lly 2 Put the vehicle in PARK P 3 Set the parking brake and then remove the key 4 Clamp the steering wheel in a straight ahead position with a clamping device designed for towing 5 Release the parking brake If you have an all wheel drive vehicle it cannot be towed with any of its wheels on the ground It can be towed with car carrier equipment Notice Towing an all wheel drive vehicle with all four wheels on the ground or even with only two of its wheels on the ground will damage drivetrain components Do not tow an all wheel drive vehicle if any of its wheels will be on the ground 4 35 Loading Your Vehicle It is very important to know how much weight your vehicle can carry This weight is called the vehicle capacity weight and includes the weight of all occupants cargo and all nonfactory installed options Two labels on your vehicle show how much weight it may properly carry the Tire and Loading Information label and the Certification Tire label Do not load your vehicle any heavier than the GVWR or either the maximum front or rear GAWR If you do parts on your vehicle can break and it can change the way your vehicle handles These could cause you to lose control and crash Also overloading can shorten the life of your vehicle 4 36 Tire and Loading Information Label TIRE AND LOADING INFORMATION SEATING CAPACITY TOTAL FRONT CENTER The combined weight of occupants and cargo should ne
254. low proper service procedures and make sure the person performing work for you is qualified to do so The air bag systems do not need regular maintenance Restraint System Check Checking Your Restraint Systems Now and then make sure the safety belt reminder light and all your belts buckles latch plates retractors and anchorages are working properly Look for any other loose or damaged safety belt system parts If you see anything that might keep a safety belt system from doing its job have it repaired Torn or frayed safety belts may not protect you ina crash They can rip apart under impact forces If a belt is torn or frayed get a new one right away Also look for any opened or broken air bag covers and have them repaired or replaced The air bag system does not need regular maintenance 1 71 Replacing Restraint System Parts After a Crash A crash can damage the restraint systems in your vehicle A damaged restraint system may not properly protect the person using it resulting in serious injury or even death in a crash To help make sure your restraint systems are working properly after a crash have them inspected and any necessary replacements made as soon as possible If you ve had a crash do you need new belts or LATCH system parts After a very minor collision nothing may be necessary But if the belts were stretched as they would be if worn during a more severe crash then you need new part
255. lowing Here are some important things to consider before you do recreational vehicle towing e What s the towing capacity of the towing vehicle Be sure you read the tow vehicle manufacturer s recommendations How far will you tow Some vehicles have restrictions on how far and how long they can tow Do you have the proper towing equipment See your dealer or trailering professional for additional advice and equipment recommendations ls your vehicle ready to be towed Just as you would prepare your vehicle for a long trip you ll want to make_sure your vehicle is prepared to be towed See Before Leaving on a Long Trip on page 4 25 Dinghy Towing Your vehicle was not designed to be towed with all of its wheels on the ground If you have a two wheel drive vehicle it can be towed with two of its wheels on the ground See Dolly Towing following If you have an all wheel drive vehicle it cannot be towed with any of its wheels on the ground It can be towed with the car carrier equipment Notice Towing an all wheel drive vehicle with all four wheels on the ground or even with only two of its wheels on the ground will damage drivetrain components Do not tow an all wheel drive vehicle if any of its wheels will be on the ground Dolly Towing lf you have a two wheel drive vehicle it can be towed with two of its wheel on the ground To dolly tow your vehicle do the following 1 Put the front wheels on a do
256. lowing record pages Also you should retain all maintenance receipts Maintenance Record Odometer i Maintenance I or Reading Serviced By Maintenance II Services Performed Maintenance Record cont d Odometer i Maintenance I or Reading Serviced By Maintenance II Services Performed Maintenance Record cont d Odometer R Maintenance I or i Section 7 Customer Assistance Information 7 2 Customer Satisfaction Procedure 00005 7 2 Online Owner Center cccceeceeeeeeeaeeeee ees 7 4 Customer Assistance for Text Telephone CTY USERS ereinen kit N 7 4 Customer Assistance Offices ccceeeee sees 7 4 GM Mobility Program for Persons with Disabilities ccccee cee eeeeeeeeeeeeeeenes 7 6 Roadside Assistance Program eseeeeee ees 7 6 Courtesy Transportation 0cceceeeeeeeeeee ees 7 8 Vehicle Data Collection and Event Data Records cccccececeeeeeeeenenes 7 10 Customer Assistance Information Reporting Safety Defects Reporting Safety Defects to the United States Government Reporting Safety Defects to the Canadian Government 000000 Reporting Safety Defects to General Motors Service Publications Ordering Information Customer Assistance Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Pontiac Normally any concerns wit
257. maged The costly repairs would not be covered by your warranty See Overheated Engine Protection Operating Mode in the Index for information on driving to a safe place in an emergency If No Steam Is Coming From Your Engine If you get an engine overheat warning but see or hear no steam the problem may not be too serious Sometimes the engine can get a little too hot when you Climb a long hill on a hot day Stop after high speed driving Idle for long periods in traffic Tow a trailer If you get the overheat warning with no sign of steam try this for a minute or so 1 If your air conditioner is on turn it off 2 Turn on your heater to full hot at the highest fan speed and open the window as necessary 3 If you are in a traffic jam shift to NEUTRAL N otherwise shift to the highest gear while driving AUTOMATIC OVERDRIVE D If you no longer have the overheat warning you can drive Just to be safe drive slower for about 10 minutes If the warning does not come back on you can drive normally If the warning continues pull over stop and park your vehicle right away If there s still no sign of steam idle the engine for three minutes while you re parked If you still have the warning turn off the engine and get everyone out of the vehicle until it cools down Also see Overheated Engine Protection Operating Mode listed previously in this section You may decide not to lift the hood bu
258. meter installed If the new one can be set to the mileage total of the old odometer then that will be done If it cannot then it is set at zero and a label must be put on the driver s door to show the old mileage reading when the new odometer was installed If your vehicle is equipped with the Driver Information Center DIC you may toggle ee ne ie display either mile or kilometers See Driver fiere Center DIC on page 3 53 Trip Odometer In addition to the standard odometer the cluster can also display a trip odometer The display can be toggled between the odometer and the trip odometer by quickly pressing and releasing the trip reset button located to the right of the temperature gage The trip odometer will continue to keep track of miles or kilometers driven even if they are not currently displayed A Canadian trip odometer will remain in metric units only To reset the trip odometer to zero 0 push and hold the trip reset button for at least one and a half seconds but less than three seconds The trip odometer that is showing in the display will be reset 3 33 Retro Active Reset The trip odometer has a feature called retro active reset This feature can be used to set the trip odometer to the number of miles or kilometers driven since the ignition was last turned on This can be used if you forget to reset your trip odometer at the beginning of a trip To use the retro active reset feature push and h
259. must be restrained while in a vehicle 1 41 Every time infants and young children ride in vehicles they should have the protection provided by appropriate restraints Young children should not use the vehicle s adult safety belts alone unless there is no other choice Instead they need to use a child restraint 1 42 People should never hold a baby in their arms while riding in a vehicle A baby doesn t weigh much until a crash During a crash a baby will become so heavy it is not possible to hold it For example in a crash at only 25 mph 40 km h a 12 Ib 5 5 kg baby will suddenly become a 240 Ib 110 kg force on a person s arms A baby should be secured in an appropriate restraint Children who are up against or very close to any air bag when it inflates can be seriously injured or killed Air bags plus lap shoulder belts offer outstanding protection for adults and older children but not for young children and infants Neither the vehicle s safety belt system nor its air bag system is designed for them Young children and infants need the protection that a child restraint system can provide Q What are the different types of add on child restraints Add on child restraints which are purchased by the vehicle s owner are available in four basic types Selection of a particular restraint should take into consideration not only the child s weight height and age but also whether or not t
260. n ccceceeceeeeeeees 2 16 Mt Wheel a ran tentontcdnaenbenwngney casa a ae 3 7 13 Tips a d Trouble arisin rbieni aaa 3 113 Tire LOW Messag sissies aar nee E Es 3 47 Tire Sidewall Labeling u sssseeeererere rene nnee 5 58 Tire SIZE menor crer herrer deb sence EREE 5 62 Tire Terminology and Definitions 5 63 TINGS 2ncaateactauetadeihakene ieatansuniqunesdteaneeencueneee 5 58 Buying New Tit Sisicct0cecvaestciientindntivetadserviee 5 71 CHAINS aema vace aca ma iaaea E 5 75 Changing a Flat Tire 2 552 poker iens 5 78 Check Tire Pressure System 0 0eeeeeeeeee 5 67 Compact Spare Tire cceeeeeeeeeeeeneee renee 5 102 If a Tire Goes Flat 00 0 cece AR skan 5 77 Inflation Tire Pressure acsee 5 66 Inspection and Rotation 5 68 Uniform Tire Quality Grading ceeeeeeee 5 72 Wheel Alignment and Tire Balance 5 73 Wheel Replacement sceeeeeeeeeeeeeeees 5 74 When It Is Time for New Tires 2 5 70 To Use the Engine Coolant Heater 2 21 TOP Strap se arr reed RsS E Arad 1 49 Top Strap Anchor Location sssseeererereee 1 50 Torque LOCK issena iaaa peidiant 2 27 Total Weight on Your Vehicle s Tires 1W 1 1W 1 1 1 4 45 Towing Recreational Vehicle c eeeeeeeeeceeeeeees 4 34 YOUR VENCE sodnar e 4 34 14 Traction Active MeSSage sirenerne 3 44 Cont
261. n inside and out Glare at night is made much worse by dirt on the glass Even the inside of the glass can build up a film caused by dust Dirty glass makes lights dazzle and flash more than clean glass would making the pupils of your eyes contract repeatedly Remember that your headlamps light up far less of a roadway when you are in a turn or curve Keep your eyes moving that way it is easier to pick out dimly lighted objects Just as your headlamps should be checked regularly for proper aim so should your eyes be examined regularly Some drivers suffer from night blindness the inability to see in dim light and are not even aware of it Driving in Rain and on Wet Roads rs rs od SI Y pie Rain and wet roads can mean driving trouble On a wet road you can not stop accelerate or turn as well because your tire to road traction is not as good as on dry roads And if your tires do not have much tread left you will get even less traction It is always wise to go slower and be cautious if rain starts to fall while you are driving The surface may get wet suddenly when your reflexes are tuned for driving on dry pavement 4 20 The heavier the rain the harder it is to see Even if your windshield wiper blades are in good shape a heavy rain can make it harder to see road signs and traffic signals pavement markings the edge of the road and even people walking It is wise to keep your wiping equipment in good
262. n to clear all numeric inputs 3 Backlight This button turns on backlighting on the remote Main Menu Press this button to view the media menu The media menu is different on every disc Use the up down right and left arrow buttons to move the cursor around the media menu After making a selection press the enter button 4 Enter Press this button to select choices highlighted in any menu amp Return Press this button to take you back one step in any menu Press this button to exit the current menu and to move to the previous menu This button will operate only when a DVD is playing and or a menu is active Oe Camera This button changes camera angles on DVDs that have this feature Press this button to call up a menu that will operate only when a DVD is being played The format and content of this function will vary from disc to disc _ Subtitles This button turns on subtitles and moves through subtitle options English Spanish French etc if available Press this button to call up a menu that will operate only when a DVD is being played The format and content of this function will vary from disc to disc Fast Forward Press this button to fast forward the DVD To stop fast forwarding press this button again This button may not work when the DVD is playing the copyright information or the previews gt Play Pause Press this button to start play of a DVD or CD Press this but
263. n Government ceeceeeeeeeeeeeeeeees General Motors United States Government e ceeeeeeeee ees Restraint System Check Checking Your Restraint Systems 008 Replacing Restraint System Parts After a Crash Restraint Systems IGMECKING rinder aaa Replacing Parts iis coc rs su rd rer cere Retained Accessory Power RAP eeeee Retro Active Reset cceceeeeeeeeeeeeeeeeeeees Right Front Passenger Position Safety Belts 1 27 Roadside Assistance Program ceceeeeeeeeeeeeeeee eee bens 7 6 Rocking Your Vehicle To Get It Out 4 33 Roof Rack System cceeeeeeeeeeeeeeee een eeeeeneees 2 38 Routing Engine Drive Belt eee 6 13 Running Your Engine While You Are Parked 2 30 Safety Belt Reminder Light icccccinceecietcigttacaiawcsecananies 3 35 Safety Belts CALC 1O8 A r E E 5 106 Center Rear Passenger Position 1 1 32 Driver Postordre ange dees mennie 1 18 How to Wear Safety Belts Properly 1 18 Questions and Answers About Safety Belts 1 17 Rear Safety Belt Comfort Guides for Children and Small Adults 2 2 2 css sanse RARE 1 34 Rear Seat Passengers W u sssseeeeeereeernenee 1 28 Right Front Passenger Position 1 27 Safety Belt Extender cceceseeeeeneeeeeeeees 1 38 Safety Belt Use During Pregnancy 1 26 Safety Belts Are for
264. n Switch See gnition Positions on page 2 18 Audio Steering Wheel Controls See Audio Steering Wheel Controls on page 3 117 Shift Lever See Automatic Transaxle Operation on page 2 22 Accessory Power Outlet See on page 3 22 Rear Outlets See on page 3 30 on page 2 36 on page 5 113 Cupholders and Ashtray See Cupholder s on page 2 34 and Ashtrays and Cigarette Lighten on page 3 23 Instrument Panel Switchbank See nstrument Pane Switehbank tchbank on page 3 19 EAE Lighter See Ashtrays and Cigarette Lighter ighten on page 3 23 Climate Controls See Climate Control System on page 3 24 or Dual Climate Control System on page 3 27 Glove Box See on page 2 34 Hazard Warning Flashers Your hazard warning flashers let you warn others They also let police know you have a problem Your front and rear turn signal lamps will flash on and off The hazard warning flasher button is located on top of the steering column Your hazard warning flashers work no matter what position your key is in and even if the key isn t in Press the button to make the front and rear turn signal lamps flash on and off Press the button again to turn the flashers off When the hazard warning flashers are on the turn signals won t work Other Warning Devices lf you carry reflective triangles you can set one up at the side of the road about 300 feet 100 m behind your vehicle Horn
265. n page 2 14 for more information If you would like to program the way the headlamps parking lamps and horn operate with remote lock confirmation and your vehicle is equipped with the Driver Information Center DIC see DIC Vehicle on page 3 57 REAR To unlock the liftgate tailgate press REAR See Liftgate Tailgate on page 2 10 for more information Remote Alarm 2 Horn Press this button to make the headlamps and parking lamps flash and the horn to sound This will allow you to attract attention if needed Press the horn symbol again to stop the alarm from sounding Matching Transmitter s to Your Vehicle Each remote keyless entry transmitter is coded to prevent another transmitter from unlocking your vehicle If a transmitter is lost or stolen a replacement can be purchased through your dealer Remember to bring any remaining transmitters with you when you go to your dealer When the dealer matches the replacement transmitter to your vehicle any remaining transmitters must also be matched Once your dealer has coded the new transmitter the lost transmitter will not unlock your vehicle Each vehicle can have a maximum of four transmitters matched to it See your dealer to match transmitters to another vehicle Battery Replacement Under normal use the battery in your remote keyless entry transmitter should last about three years KEY FOB BATTERY LOW Bi United States Canada You can tel
266. n perform very well in emergencies like these First apply your brakes See lating on page 4 7 It is better to remove as much speed as you can from a possible collision Then steer around the problem to the left or right depending on the space available An emergency like this requires close attention and a quick decision If you are holding the steering wheel at the recommended 9 and 3 o clock positions you can turn it a full 180 degrees very quickly without removing either hand But you have to act fast steer quickly and just as quickly straighten the wheel once you have avoided the object The fact that such emergency situations are always possible is a good reason to practice defensive driving at all times and wear safety belts properly Off Road Recovery You may find that your right wheels have dropped off the edge of a road onto the shoulder while you re driving If the level of the shoulder is only slightly below the pavement recovery should be fairly easy Ease off the accelerator and then if there is nothing in the way steer so that your vehicle straddles the edge of the pavement You can turn the steering wheel up to one quarter turn until the right front tire contacts the pavement edge Then turn your steering wheel to go straight down the roadway Passing The driver of a vehicle about to pass another on a two lane highway waits for just the right moment accelerates moves around the vehicle ahea
267. n while it is heating will not allow the lighter to back away from the heating element when it is hot Damage from overheating may occur to the lighter or heating element or a fuse could be blown Do not hold a cigarette lighter in while it is heating Notice If you put papers or other flammable items in the ashtray hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle Never put flammable items in the ashtray 3 23 Climate Controls Climate Control System With this system you can control the heating cooling and ventilation for your vehicle Operation Turn the right knob clockwise or counterclockwise to direct the airflow inside your vehicle 3 24 To change the current mode select one of the following pe Vent This mode directs air to the instrument panel outlets Wi Bi Level This mode directs half of the air to the instrument panel outlets then directs the remaining air to the floor outlets Cooler air is directed to the upper outlets and warmer air to the floor outlets WWW Floor This mode directs most of the air to the floor outlets Use this mode to send air to the rear of the vehicle Keep the area under the front seats free of objects that could obstruct airflow to the rear of the vehicle The right knob can also be used to select defog or defrost mode For more information see Defogging and Defrosting later in this section Fan Turn the
268. nance facts Service Traction System Warning Message SERVICE TRACTION TC Canada SYSTEM United States If your vehicle has the traction control system and this message is displayed when you re driving there may be a problem with your traction control system Your vehicle may need service When this message is displayed the traction control system will not limit wheel spin Adjust your driving accordingly If there s an engine related and brake system problem that is specifically related to traction control the traction control system will turn off and the warning message will come on If the traction control system warning message comes on and stays on for an extended period of time when the system is turned on your vehicle needs service 3 43 Traction Active Message TC Canada TRACTION ACTIVE United States If your vehicle has the traction control system the TRACTION ACTIVE message will appear when the traction control system is limiting wheel spin You may feel or hear the system working but this is normal Slippery road conditions may exist if this message appears so adjust your driving accordingly The message will stay on for a few seconds after the traction control system stops limiting wheel spin 3 44 Engine Coolant Temperature Warning Message Canada United States This message will come on when your engine gets too hot If this message comes on it means that y
269. nates firing groups of cylinders helps prevent engine damage In this mode you will notice a significant loss in power and engine performance The temperature gage will indicate an overheat condition exists Driving extended miles km and or towing a trailer in the overheat protection mode should be avoided Notice After driving in the overheated engine protection operating mode to avoid engine damage allow the engine to cool before attempting any repair The engine oil will be severely degraded Repair the cause of coolant loss change the oil and reset the oil life system See Engine Oil in the Index 5 25 If Steam Is Coming From Your Engine Steam from an overheated engine can burn you badly even if you just open the hood Stay away from the engine if you see or hear steam CAUTION Continued 5 26 coming from it Just turn it off and get everyone away from the vehicle until it cools down Wait until there is no sign of steam or coolant before you open the hood If you keep driving when your engine is overheated the liquids in it can catch fire You or others could be badly burned Stop your engine if it overheats and get out of the vehicle until the engine is cool See Overheated Engine Protection Operating Mode in the Index for information on driving to a safe place in an emergency Notice If your engine catches fire because you keep driving with no coolant your vehicle can be badly da
270. nch into the hoist shaft Turn the folding wrench counterclockwise to lower the compact spare tire to the ground Continue turning the wrench until the spare tire can be pulled out from under the vehicle To remove the spare tire from the cable tilt the retainer and slip it through the wheel opening After removing the spare tire turn the wrench clockwise to raise the cable back up Do not store a full size or a flat road tire under the vehicle See Storing a Flat Vehicles without the Sliding Rear Convenience Tray and Storing a Flat Vehicles with the Sliding Rear Convenience Tray later in this section To continue changing the flat tire see Removing the Flat Tire and Installing the Spare Tire later in this section 5 81 If the spare tire will not lower the secondary latch may be engaged causing the tire not to lower Do the following to check the cable 1 Check under the vehicle to see if the cable is visible 2 If it s not visible see Secondary Latch System later in this section If it is visible first try to tighten the cable by turning the folding wrench clockwise until you hear two clicks or feel it skip twice You cannot over tighten the cable 5 82 3 Then loosen the cable by turning the wrench counterclockwise three or four turns 4 If the spare tire has not lowered tighten the cable all the way and then loosen it at least two times If the spare tire did lowe
271. nded Fluids and Lubricants 6 12 Scheduled Maintenance 0 ceceeeeeeeneeeeen tees 6 4 Normal Maintenance Replacement Parts 6 13 Additional Required Services eeeeeeeeee ee 6 6 Engine Drive Belt Routing eee 6 13 Maintenance Footnotes ccceeeeeeeeeeeee eters 6 7 Maintenance Record eceeeeeeeeeeeeeeeeeeees 6 14 6 1 Maintenance Schedule Introduction Important Keep engine oil at the proper level and change as recommended Protection Plan Have you purchased the GM Protection Plan The Plan supplements your new vehicle warranties See your Warranty and Owner Assistance booklet or your dealer for details Maintenance Requirements Notice Maintenance intervals checks inspections replacement parts and recommended fluids and lubricants as prescribed in this manual are necessary to keep your vehicle in good working condition Any damage caused by failure to follow scheduled maintenance may not be covered by warranty Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your vehicle in good working condition but also helps the environment All recommended maintenance is important Improper vehicle maintenance can even affect the quality of the air we breathe Improper fluid levels or the wrong tire inflation can increase the level of emissions from your vehicle To help protect our environment and to keep you
272. nder the root directory When all tracks from the root directory have been played play will continue from files according to their numerical listing After playing the last track from the last folder play will begin again at the first track of the first folder or root directory 3 85 When play enters a new folder the display will not automatically show the new folder name unless you have chosen the folder mode as the default display see RCL later in this section The new track name will be displayed File System and Naming The song name that will be displayed will be the song name that is contained in the ID3 tag If the song name is not present in the ID3 tag then the radio will display the file name without the extension such as mp3 as the track name Track names longer than 32 characters or 4 pages will be shortened The display will not show parts of words on the last page of text and the extension of the filename will not be displayed Preprogrammed Playlists You can access preprogrammed playlists which were created by WinAmp MusicMatch or Real Jukebox software however you will not have editing capability These playlists will be treated as special folders containing compressed audio song files 3 86 Playing an MP3 With the ignition on insert a CD partway into the slot label side up The player will pull it in and the CD will begin to play after the player has read the table of contents and t
273. nds upon four things The amount of alcohol consumed The drinker s body weight The amount of food that is consumed before and during drinking The length of time it has taken the drinker to consume the alcohol According to the American Medical Association a 180 Ib 82 kg person who drinks three 12 ounce 355 ml bottles of beer in an hour will end up with a BAC of about 0 06 percent The person would reach the same BAC by drinking three 4 ounce 120 ml glasses of wine or three mixed drinks if each had 1 1 2 ounces 45 ml of liquors like whiskey gin or vodka It is the amount of alcohol that counts For example if the same person drank three double martinis 3 ounces or 90 ml of liquor each within an hour the person s BAC would be close to 0 12 percent A person who consumes food just before or during drinking will have a somewhat lower BAC level There is a gender difference too Women generally have a lower relative percentage of body water than men Since alcohol is carried in body water this means that a woman generally will reach a higher BAC level than a man of her same body weight will when each has the same number of drinks The law in an increasing number of U S states and throughout Canada sets the legal limit at 0 08 percent In some other countries the limit is even lower For example it is 0 05 percent in both France and Germany The BAC limit for all commercial drivers in the United States
274. ndshiela G H J K Engine Air Cleaner Filter See Cleaner Filten on page 5 18 Washer Fluid on page 5 36 Battery See on page 5 41 Radiator Pressure Cap See Radiator Pressure Cap on page 5 25 Engine Oil Fill Cap See on page 5 13 Engine Oil Dipstick See on page 5 13 Coolant Recovery Tank See Engine Coolantjon page 5 22 Engine Oil Checking Engine Oil It is a good idea to check your engine oil every time you get fuel In order to get an accurate reading the oil must be warm and the vehicle must be on level ground The engine oil dipstick handle is a yellow loop See Engine Compartment Overviewjon page 5 12 for e location of the engine oil dipstick Turn off the engine and give the oil several minutes to drain back into the oil pan If you don t the oil dipstick might not show the actual level Pull out the dipstick and clean it with a paper towel or cloth then push it back in all the way Remove it again keeping the tip down and check the level When to Add Engine Oil If the oil is at or below the cross hatched area at the tip of the dipstick then you will need to add at least one quart of oil But you must use the right kind This section explains what kind of oil to use For engine oil crankcase capacity see Capacities and Specficationd on page 5 178 Notice Do not add too much oil If your engine has so much oil that the oil level gets above the cross hatched area
275. ne change if the arrow flashes faster than normal a signal bulb may be burned out and other drivers will not see your turn signal lf a bulb is burned out replace it to help avoid an accident If the arrows do not go on at all when you signal a turn check for burned out bulbs and check the fuse See Fuses and Circuit Breakers on page 5 113 If you have a trailer towing option with added wiring for the trailer lamps the signal indicator will flash at a normal rate even if a turn signal bulb is burned out Check the front and rear turn signal lamps regularly to make sure they are working Turn Signal On Chime If either turn signal is left on for more than 3 4 mile 1 2 km a chime will sound to let you know to turn it off To turn off the chime turn off the signal Headlamp High Low Beam Changer To change the headlamps from low to high push the turn signal lever away from you and release it To change the headlamps from high to low pull the lever toward you When the high beams are on this light on the instrument panel cluster and the HUD display will also be on Flash to Pass When the headlamps are off pull the lever toward you to momentarily switch on the high beams This will signal that you are going to pass When you release the lever they will turn off Windshield Wipers WIPER Turn the band marked WIPER to control the windshield wipers MIST For a single wiping cycle turn the band to MIST H
276. ne of the following to install the nets Connect the upper hooks on the side convenience nets to the top loops on the sidewall trim Then attach the lower hooks on the side convenience nets to the lower hooks on the sidewall trim or e connect the upper hooks on the side convenience nets to the top of the front and rear convenience nets Then connect the lower hooks on the side convenience nets to the floor retainers on the floor of the rear of the vehicle The cargo net system has a maximum capacity of 100 Ibs 45 4 kg for the front and rear nets and 35 Ibs 15 9 kg for the side nets It is not designed to hold larger heavier loads Store such loads on the floor of your vehicle as far forward as you can When not in use it is recommended that you then take down the convenience nets to extend life and retain their elasticity and to keep the rear exit clear Store the net in one of the storage compartments Sliding Rear Convenience Tray If any removable convenience item is not secured properly it can move around ina collision or sudden stop People in the vehicle could be injured Be sure to secure any such item properly Your vehicle may have a sliding rear convenience tray The sliding rear convenience tray can be pulled out onto the tailgate making it easier to load or unload items To use the tray do the following 1 Push the release lever located in front of the handle of the tray to release the pin from the
277. nector by lifting up the gray tabs and separate the connector from the bulb base 9 Install the new bulb into the electrical connector Push the bulb firmly enough so that the gray tabs hook over the tab on the bulb 10 Put the bulb assembly back into the lamp housing and turn the bulb socket one quarter of a turn counterclockwise 5 52 Front Turn Signal Sidemarker and Parking Lamps 1 Open the hood 2 Remove the two inboard screws attaching the lamp to the fender bracket 3 Unsnap the lamp assembly by lifting straight up 4 Pull the lamp assembly away from the vehicle Unscrew the bulb socket from the lamp assembly by pressing the tab while turning it counterclockwise Replace the bulb by pulling the old one out and gently pushing the new one into the lamp socket Line up the tabs on the socket with the gaps in the socket holes and screw the bulb socket back into the lamp housing until a click is heard the tab popping back out To reinstall the lamp assembly align the tapered pin on the bottom of the lamp with the plastic socket on the fender bracket Push down until the pin snaps into the socket Reinstall the two screws that were removed in Step 2 5 53 Taillamps Stoplamps and Back up Lamps 1 Open the liftgate and the tailgate 2 Remove the two screws from the taillamp housing 3 Turn the lamp outboard then pull the assembly firmly rearward 5 54 A
278. nesseseeseeee ease 2 32 Capacities and Specifications 5 118 Storage Areas hee eeccccceccceccceceeeeueeeueeeuetnaeens 2 34 Maintenance Schedule 0000ceeseeeeeeeeeees 6 1 SUNMOLE ES e a a 2 48 Maintenance Schedule aerenc 6 2 Instrument Panel E L E E E ET 3 1 Customer Assistance Information MN EE AEE T TA Instrument Panel Overview c cceeeeeeeeeee es 3 4 Customer Assistance Information 7 2 Climate Controls oo eeeceeeeececeeeeeeeeeeeeeeeees 3 24 Reporting Safety Defects oo eee 7 11 Warning Lights Gages and Indicators __ 3 31 WO sieros a teem ames ae ed 1 Message Center ccceccecsecceeseeeeeeeeeereners 3 43 Driver Information Center DIC 3 53 Audio System s Y PONTIAC GENERAL MOTORS GM the GM Emblem PONTIAC the PONTIAC Emblem and the name AZTEK are registered trademarks of General Motors Corporation This manual includes the latest information at the time it was printed We reserve the right to make changes after that time without further notice For vehicles first sold in Canada substitute the name General Motors of Canada Limited for Pontiac Division whenever it appears in this manual Please keep this manual in your vehicle so it will be there if you ever need it when you re on the road If you sell the vehicle please leave this manual in it so the new owner can use it Litho in U S A Part No 10337756
279. ng Know the best way to get to where you are going Get a city map and plan your trip into an unknown part of the city just as you would for a cross country trip Try to use the freeways that rim and crisscross most large cities You will save time and energy See on page 4 24 Treat a green light as a warning signal A traffic light is there because the corner is busy enough to need it When a light turns green and just before you start to move check both ways for vehicles that have not cleared the intersection or may be running the red light 4 23 Freeway Driving Mile for mile freeways also called thruways parkways expressways turnpikes or superhighways are the safest of all roads But they have their own special rules 4 24 The most important advice on freeway driving is Keep up with traffic and keep to the right Drive at the same speed most of the other drivers are driving Too fast or too slow driving breaks a smooth traffic flow Treat the left lane on a freeway as a passing lane At the entrance there is usually a ramp that leads to the freeway If you have a clear view of the freeway as you drive along the entrance ramp you should begin to check traffic Try to determine where you expect to blend with the flow Try to merge into the gap at close to the prevailing speed Switch on your turn signal check your mirrors and glance over your shoulder as often as necessary Try to blend smoothly with t
280. nition PoSitions snis neiii aae 2 18 Infants and Young Children Restraints 1 41 Inflation Tire Pressure c eeeeeeeeeeeeeeee ees 5 66 Instrument Panel CIUSTON a sense FE E 3 32 OVGIVICW iriiri aei anioe ea aan A 3 4 SWItChbAaNK ania e ae aea a ER 3 19 Instrument Panel Brightness ccecce 3 16 Integrated Windshield Antenna 3 119 Interior Lamps eniten Eai 3 15 Interior Lamps Control W u ssssseeeeeererenernere 3 16 Interior Lighting Delay 2522 La re aar 3 58 Interior Lighting On ceeeeeeee eee o teens 3 59 JUMP Staring synene io a ei 5 42 Keyless Entry System sssseseeeeeeererkrr rr nnnee 2 3 KEYS cds 3 ans aaa Ale er S 2 2 Lamps EXT GMOMe ats tactnad ac tere ass een re heles rene 3 13 IMETO areira naain 3 15 Lamps On Reminder W u ssseeeeeeereer reen ener 3 14 Lap Shoulder Belt eeeeeeeeeeee 1 18 1 28 1 32 LATCH System Child Restraints ccceeeeeeeeeneeeeeneeeeeneees 1 52 Securing a Child Restraint Designed for the LATCH System ccceeeeeeeeeeeenes 1 54 Leaving Your Vehicle eceeeeeeeeeeeeeeeeeees 2 10 Leaving Your Vehicle With the Engine Running 2 27 Liftgate Tall ate ceneni penra 2 10 Liftgate Tailgate Release i n 2 11 Light Air Bag Readiness eceeeeeeeeeeeeeeerees 3 35 Anti Lock Brake System Warning 6 3 37 Brake System Warning ceseeeeeeeneeeeeeeees 3 36
281. nnan anargie 3 8 Traction Active Message see 3 44 Exterior Lamps sirsie anana Es 3 13 Engine Coolant Temperature Warning Interior Lamps OEEEE ELLE EF LEE E EERE FEE EEEELEREEEE 3 15 Message E 3 44 Instrument Panel Switchbank W G u sseseerereereree 3 19 Charging System Indicator Message W1 1 1 3 45 Head Up Display HUD eceeeeetriee 3 20 Low Oil Pressure Message ccccceeeeeeeeees 3 45 Accessory Power Outlets E RER 3 22 Change Engine Oil Message cccseseeeeees 3 46 Ashtrays and Cigarette Lighter 1 3 23 Low Tire Message 0 eecececeeeeeeeeeeeeeeeeeeeaee ees 3 47 Climate Controls cccceeeeeeeeeee eee eee eee ees 3 24 Door Ajar Warning Message c c 3 47 Climate Control System ceeeeeeeeeeeeeeee tenes 3 24 Rear Hatch Ajar Warning Message 4 3 48 Dual Climate Control System ssseeeeee 3 27 PASS Key III Security Message 0000 3 48 Outlet Adjustment ceeeeeeeeeeeeeeeeeee eee eenes 3 30 All Wheel Drive Disable Warning Message 3 49 Warning Lights Gages and Indicators 3 31 Low Washer Fluid Warning Message 3 49 Instrument Panel Cluster cccccceeeeee sees 3 32 Low Fuel Warning Message ecses 3 50 Speedometer and Odometer cc00cceeeee 3 33 Low Brake Fluid Warning Message 3 50 Tachometer ikana E iE 3 34 Se
282. nnect the red positive cable from the other vehicle 5 Return the remote positive terminal cover to its original position 5 47 All Wheel Drive To get an accurate reading the vehicle should be on a level surface If you have an all wheel drive vehicle be sure to __ If the level is below the bottom of the filler plug hole perform the lubricant checks described in this section you ll need to add some lubricant Add enough lubricant However they have two additional systems that to raise the level to the bottom of the filler plug hole need lubrication What to Use Transfer Case Power Transfer Unit oe eee TE EEE TT When to Check Lubricant eter to tne Maintenance ocneadule to determine wna kind of lubricant to use See Recommended Fluids Refer to the Maintenance Schedule to determine how and Lubricants on page 6 12 often to check the lubricant See Schedulea on page 6 4 How to Check Lubricant 5 48 Carrier Assembly Differential Rear Drive Module When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it See Scheduled Maintenance on page 6 4 How to Check Lubricant To get an accurate reading the vehicle should be on a level surface If the level is below the bottom of the filler plug hole you ll need to add some lubricant Add enough lubricant to raise the level to the bottom of the filler plug hole A fluid l
283. nnen eee Eaa Lori 4 3 Loading 553 seer abe nb ads boede 4 36 Service Soon Message eeeeeeeeeeeeeeeeeeee 3 51 SY MBO SEE an a re a E AE iv Vehicle Data Collection and Event Data Records 7 10 Vehicle Identification Number VIN rnencias ENES 5 111 Service Parts Identification Label 5 111 Vehicle Personalization DIC SE En a eE a A N 3 57 Vehicle Storage sci son seler banket innana 5 41 Ventilation Adjustment a asaseseeernrnrennrnrennenna 3 30 Vid o SGrOGN rer errors 3 105 Visor Vanity MINOR cinas ube beee 2 13 MISOIS eat ele SN SE REE 2 13 Warm Up Shift vscciesezsccticiees ct sastldiveedenseeeseelve 2 24 Warning Lights Gages and Indicators 3 31 Warnings Hazard Warning Flashers ccceeeeeeeeeeeeee 3 6 Other Warning Devices ceceeeeeeeeeeeeen tees 3 7 Safety and Symbols cccceeeeeeeeeeeeeeeeeeeenes iii Vehicle Damage iesistie pen iv Washer Fluid Low Warning Message 3 49 Washing Your Vehicle cceeeeeeeeeee eee eee ees 5 106 Weight of the Trailer cceseeeeeeeeeeeeee eee ee 4 43 Weight of the Trailer Tongue c eeeeeeeee es 4 44 What Coolant to Use isse skeer 5 23 What Kind of Engine Oil to Use eee 5 15 What Power Steering Fluid to Use 00 5 36 What to Do with Used Oil 20 0 0 ceeeeeeeeee neers 5 18 What Washer Fluid to Use 0 0 00 eeeeeeeeeee eee e
284. nt and wheel balancing are not needed However if you notice unusual tire wear or your vehicle pulling one way or the other the alignment may need to be reset If you notice your vehicle vibrating when driving on a smooth road your wheels may need to be rebalanced 5 73 Wheel Replacement Replace any wheel that is bent cracked or badly rusted or corroded If wheel nuts keep coming loose the wheel wheel bolts and wheel nuts should be replaced If the wheel leaks air replace it except some aluminum wheels which can sometimes be repaired See your dealer if any of these conditions exist Your dealer will know the kind of wheel you need Each new wheel should have the same load carrying capacity diameter width offset and be mounted the same way as the one it replaces If you need to replace any of your wheels wheel bolts or wheel nuts replace them only with new GM original equipment parts This way you will be sure to have the right wheel wheel bolts and wheel nuts for your vehicle 5 74 Using the wrong replacement wheels wheel bolts or wheel nuts on your vehicle can be dangerous It could affect the braking and handling of your vehicle make your tires lose air and make you lose control You could have a collision in which you or others could be injured Always use the correct wheel wheel bolts and wheel nuts for replacement Notice The wrong wheel can also cause problems with bearing life brake cooling
285. nt number shown on the original battery s label We recommend an ACDelco battery See Engine Compartment Overview on page 5 12 for battery location Warning Battery posts terminals and related accessories contain lead and lead compounds chemicals known to the State of California to cause cancer and reproductive harm Wash hands after handling Vehicle Storage If you are not going to drive your vehicle for 25 days or more remove the black negative cable from the battery This will help keep your battery from running down Batteries have acid that can burn you and gas that can explode You can be badly hurt if you are not careful See Jump Starting on page 5 42 for tips on working around a battery without getting hurt Contact your dealer to learn how to prepare your vehicle for longer storage periods Also for your audio system see Theft Deterren on page 3 116 5 41 Jump Starting If your battery has run down you may want to use another vehicle and some jumper cables to start your vehicle Be sure to follow the steps below to do it safely Batteries can hurt you They can be dangerous because They contain acid that can burn you They contain gas that can explode or ignite They contain enough electricity to burn you If you do not follow these steps exactly some or all of these things can hurt you Notice Ignoring these steps could result in costly damage to your vehicle that wo
286. o Helm Incorporated P O Box 07130 Detroit MI 48207 Prices are subject to change without notice and without incurring obligation Allow ample time for delivery Note to Canadian Customers All listed prices are quoted in U S funds Canadian residents are to make checks payable in U S funds A Anti Lock Brake System Warning Light 3 37 Appearance Care ceeceeeeeeeeceeeeeeeeeeeeeeeens 5 103 About Driving Your Vehicle eee 0 2 Care of Safety Belts ccceceeeceee eee eeees 5 106 Accessory Inflator sissioni E 5 76 Chemical Paint Spotting cee 5 109 Accessory Power Outlets 0 c ee 3 22 Cleaning the Inside of Your Vehicle 5 103 Adding Washer FIUId 22522 morer eee sians 5 37 Cleaning the Outside of Your Vehicle 5 106 Additional Program Information c ee 7 9 Finish Damage scicviscostaricanandtacdiamcathnimdwnnene 5 109 Additives Fuel ahh ene 5 6 Sheet Metal Damage ccccccceeeeeeeeeeeees 5 108 Add On Electrical Equipment 208 5 112 Underbody Maintenance 0ccceeeeeeeeee 5 109 Adjusting the Speakers Vehicle Care Appearance Materials 5 110 Balance Fade ce ceeeeeeee eee 3 68 3 78 3 92 WeatherstlipS srren iin terien aT 5 106 Air Bag Arming with the Power Lock Switch 2 15 Readiness Light cceceeceeeeeeeeeeneeeeee eens 3 35 A
287. o go to another station within that PTY and the PTY is displayed press either SEEK arrow once If the PTY is not displayed press either SEEK arrow twice to display the PTY and then to go to another station 5 Press PROG TYPE to exit program type mode If PTY times out and is no longer on the display go back to Step 1 If both PTY and TRAF are on the radio will search for stations with the selected PTY and traffic announcements A SCAN V You can scan the stations within a PTY by performing the following 1 Press PROG TYPE to activate program type select mode The PTY symbol will appear on the display 2 Turn the SELECT knob to select a PTY 3 Once the desired PTY is displayed press and hold either SCAN arrow and the radio will begin scanning the stations in the PTY 4 Press either SCAN arrow to stop at a station lf both PTY and TRAF are on the radio will scan for stations with the selected PTY and traffic announcements BAND Alternate Frequency Alternate frequency allows the radio to switch to a stronger station with the same programming To turn alternate frequency on press and hold BAND for two seconds AF ON will appear on the display The radio may switch to stronger stations To turn alternate frequency off press and hold BAND again for two seconds AF OFF will appear on the display The radio will not switch to other stations This function does not apply for XM Satellite Radio Service Setting
288. o nearest dealership for warranty service Change a flat tire Jump starts We have quick easy access to telephone numbers of the following additional services depending on your needs Hotels Glass replacement Tire repair facilities Rental vehicle or taxis Airports or train stations e Police fire departments or hospitals In many instances mechanical failures are covered under Pontiac s comprehensive warranty However when other services are utilized our advisors will explain any payment obligations you might incur For prompt and efficient assistance when calling please provide the following information to give the advisor Location of vehicle Telephone number of your location Vehicle model year and color e Mileage of vehicle Vehicle Identification Number VIN Vehicle license plate number Pontiac reserves the right to limit services or reimbursement to an owner or driver when in Pontiac s judgement the claims become excessive in frequency or type of occurrence While we hope you never have the occasion to use our service it is added security while traveling for you and your family Remember we re only a phone call away Pontiac Roadside Assistance 1 800 ROADSIDE or 1 800 762 3748 text telephone TTY users call 1 888 889 2438 Canadian Roadside Assistance Vehicles purchased in Canada have an extensive Roadside Assistance program accessible from anywhere in Canada or the United
289. o stations SEEK V Press the up or the down arrow to go to the next or to the previous station and stay there The radio will seek only to stations that are in the selected band and only to those with a strong signal A SCAN V Press and hold either SCAN arrow for two seconds until SCAN appears on the display and you hear a beep The radio will go to a station play for a few seconds then go on to the next station Press either SCAN arrow again to stop scanning To scan preset stations press and hold either SCAN arrow for more than four seconds until PSCAN and the preset number appear on the display You will hear a double beep The radio will go to the first preset station stored on your pushbuttons play for a few seconds then go on to the next preset station Press either SCAN arrow again to stop scanning presets The radio will scan only to stations that are in the selected band and only to those with a strong signal Setting Preset Stations The six numbered pushbuttons let you return to your favorite stations You can set up to 30 stations six FM1 six FM2 and six AM six XM1 and six XM2 48 contiguous US states if equipped by performing the following steps 1 Turn the radio on 2 Press BAND to select FM1 FM2 AM or XM1 or XM2 3 Tune in the desired station 4 Press EQ to select the equalization 5 Press and hold one of the six numbered pushbuttons until you hear a beep Whenever you press that
290. o your vehicle unless you check with your dealer first Some electrical equipment can damage your vehicle and the damage wouldn t be covered by your warranty Some add on electrical equipment can keep other components from working as they should Your vehicle has an air bag system Before attempting to add anything electrical to vour vehicle see Servicing Your Air Bag Equipped Vehicle on page 1 71 Headlamp Wiring The headlamp wiring is protected by different fuses located in the underhood fuse block An electrical overload may cause the lamps to go off and remain that way If this happens replace the right fuse with one of the same kind and amperage 5 112 Windshield Wiper Fuses The windshield wiper motor is protected by an internal circuit breaker and a fuse If the motor overheats due to heavy snow etc the wiper will stop until the motor cools If the overload is caused by some electrical problem be sure to get it fixed Power Windows and Other Power Options Circuit breakers in the floor console fuse block protect the power windows and other power accessories When the current load is too heavy the circuit breaker opens and closes protecting the circuit until the problem is fixed Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses circuit breakers and fusible thermal links Look at the silver colored L Band inside the fuse If the L Band
291. of Park P Your vehicle has an automatic transaxle shift lock control system You have to fully apply your regular brakes before you can shift from PARK P when the rine ON So Auto Heit Ter cals Operon on page 2 22 If you cannot shift out of PARK P ease pressure on the shift lever by pushing the shift lever all the way into PARK P as you maintain brake application Then hold the button on the lever and move the shift lever out of PARK P 2 28 Parking Over Things That Burn Things that can burn could touch hot exhaust parts under your vehicle and ignite Do not park over papers leaves dry grass or other things that can burn Engine Exhaust Your vehicle was damaged when driving over high points on the road or over road debris Repairs were not done correctly Engine exhaust can kill It contains the gas carbon monoxide CO which you can not see or smell It can cause unconsciousness and death Your vehicle or exhaust system had been modified improperly If you ever suspect exhaust is coming into your vehicle Drive it only with all the windows down to blow out any CO and Have your vehicle fixed immediately You might have exhaust coming in if Your exhaust system sounds strange or different Your vehicle gets rusty underneath Your vehicle was damaged in a collision CAUTION Continued 2 29 Running Your Engine While You Are Parked It is better not to park with
292. of the proper maintenance of your vehicle Gasoline Octane Use regular unleaded gasoline with a posted octane of 87 or higher If the octane is less than 87 you may get a heavy knocking noise when you drive If this occurs use a gasoline rated at 87 octane or higher as soon as possible Otherwise you might damage your engine A little pinging noise when you accelerate or drive uphill is considered normal This does not indicate a problem exists or that a higher octane fuel is necessary If you are using 87 octane or higher octane fuel and hear heavy knocking your engine needs service Gasoline Specifications It is recommended that gasoline meet specifications which were developed by automobile manufacturers around the world and contained in the World Wide Fuel Charter which is available from the Alliance of Automobile Manufacturers at www autoalliance org Gasoline meeting these specifications could provide improved driveability and emission control system performance compared to other gasoline In Canada look for the Auto Makers Choice label on the pump Canada Only California Fuel If your vehicle is certified to meet California Emission Standards see the underhood emission control label it is designed to operate on fuels that meet California specifications If this fuel is not available in states adopting California emissions standards your vehicle will operate satisfactorily on fuels meeting federal sp
293. of the tire farthest away from the one being changed That would be the tire on the other side of the vehicle at the opposite end Removing the Spare Tire and Tools The equipment you ll need is located in the storage compartment at the rear of the vehicle on the passenger s side 1 Remove the side convenience net The following steps will tell you how to use the jack and 2 Open the jack storage compartment by lifting up the change a tire tab and pulling the cover off 5 79 A Jack C Jacking B Wing Bolt Instructions D Folding Wrench 3 Remove the jack and jacking tools by turning the wing bolt counterclockwise Slightly lift up the jack from the bracket tab and then take it out of the storage compartment 4 Separate the jack and remove the folding wrench from the jack 5 80 The tools you ll be using include the jack A folding wrench B extension tube C wing nut D and J Hook E Removing the Spare Tire Vehicles without the Sliding Rear Convenience Tray The compact spare tire is located under the vehicle behind the rear bumper Use the spare tire hoist to raise lower and store the compact spare se Com on page 5 102 for more information about the compact spare A B C 1 NM Hoist Shaft Folding Wrench Hoist Assembly D Retainer E Spring F Compact Spare Tire Flip the rear cargo area carpet cut out to expose the hoist shaft Attach the folding wre
294. olant Heater aansen 2 21 SUMMOOR oreiro tenet antares ss elle 2 48 Automatic Transaxle Operation 2 2 22 2 1 Keys Leaving children in a vehicle with the ignition key is dangerous for many reasons A child or others could be badly injured or even killed They could operate the power windows or other controls or even make the vehicle move Do not leave the keys in a vehicle with children Your vehicle s key can be used for the ignition as well as the driver s door lock the liftgate tailgate lock and the storage compartments If you need a new key contact your dealer who can obtain the correct key code Your vehicle has the PASS Key III vehicle theft system The key has a transponder in the key head that matches a decoder in the vehicle s steering column If a replacement key or any additional key is needed you must purchase this key from your dealer The key will have PK3 stamped on it Keep the bar code tag that came with the original keys Give this tag to your dealer if you need a new key made Any new PASS Key III key must be programmed before it will start your vehicle See on page 2 16 for more information on programming your new key Notice If you ever lock your keys in your vehicle you may have to damage the vehicle to get in Be sure you have spare keys of your vehicle see Q Roadside Assistance Prog on page 7 6 for more information If your vehicle is equipped with the OnStar s
295. old it there until the wipers start then let go The wipers will stop after one cycle If you want more cycles hold the band on mist longer Delay For delayed wiping cycles you can set the wiper speed for a long or short delay between wipes This can be very useful in light rain or snow Turn the band to choose the delay time The closer to LO the shorter the delay time LO For steady wiping cycles at low speed turn the band away from you to the LO position HI For high speed wiping turn the band away from you to the HI position OFF To stop the wipers turn the band to OFF Remember that damaged wiper blades may prevent you from seeing well enough to drive safely To avoid damage be sure to clear ice and snow from the wiper blades before using them If they re frozen to the windshield carefully loosen or thaw them If your blades do become damaged get new blades or blade inserts Heavy snow or ice can overload your wipers A circuit breaker will stop them until the motor cools Clear away snow or ice to prevent an overload Windshield Washer W To wash your windshield press and hold the windshield washer paddle The washers and wipers will operate When you release the paddle the washers will stop and the wipers will continue to operate for two cycles unless your wipers were already on In that case the wipers will resume the wiper speed you had selected earlier In freezing weather do not use your washer
296. old the knob until the display flashes The selected display will now be the default 3 76 Finding a Station BAND Press this button to switch between FM1 FM2 AM or XM1 or XM2 48 contiguous US states if equipped The display will show your selection TUNE Turn this knob to select radio stations SEEK V Press the up or the down arrow to go to the next or to the previous station and stay there The radio will seek only to stations that are in the selected band and only to those with a strong signal A SCAN V Press and hold either SCAN arrow for two seconds until SCAN appears on the display and you hear a beep The radio will go to a station play for a few seconds then go on to the next station Press either SCAN arrow again to stop scanning To scan preset stations press and hold either SCAN arrow for more than four seconds until PSCAN and the preset number appear on the display You will hear a double beep The radio will go to the first preset station stored on your pushbuttons play for a few seconds then go on to the next preset station Press either SCAN arrow again to stop scanning presets The radio will scan only to stations that are in the selected band and only to those with a strong signal Setting Preset Stations The six numbered pushbuttons let you return to your favorite stations You can set up to 30 stations six FM1 six FM2 and six AM six XM1 and six XM2 48 contiguous US states if e
297. old the trip reset button for at least three seconds The trip odometer will then display the number of miles or kilometers driven since the ignition was last turned on and you began driving If you use the retro active reset feature after you have started the vehicle but before you begin moving the display will show the number of miles or kilometers you drove during the last ignition cycle Once you begin driving the trip odometer will accumulate mileage For example if you have driven 5 0 miles 8 0 km since you started your vehicle and then activate the retro active reset feature the display will show 5 0 miles 8 0 km As you drive the display will then increase to 5 1 miles 8 2 km 5 2 miles 8 4 km etc 3 34 Tachometer The tachometer displays the engine speed in revolutions per minute rpm Notice If you operate the engine with the tachometer in the shaded warning area your vehicle could be damaged and the damages would not be covered by your warranty Do not operate the engine with the tachometer in the shaded warning area Safety Belt Reminder Light When the key is turned to ON or START a chime will come on for several seconds to remind people to fasten their safety belts The safety belt light will also come on and stay on for several seconds If the driver s belt is already buckled neither the chime nor the light will come on LZ Air Bag Readiness Light There is an air bag read
298. om XXX kilograms or XXX pounds The resulting figure equals the available amount of cargo and luggage load capacity For example if the XXX amount equals 1400 Ibs and there will be five 150 Ib passengers in your vehicle the amount of available cargo and luggage load capacity is 650 Ibs 1400 750 5 x 150 650 Ibs Determine the combined weight of luggage and cargo being loaded on the vehicle That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4 If your vehicle will be towing a trailer the load from your trailer will be transferred to your vehicle Consult this manual to determine how this reduces the available cargo and luggage load capacity for your vehicle 4 37 See Towing a Trailer on page 4 42 for important information on towing a trailer towing safety rules and trailering tips Example 2 Loading Your Vehicle Vehicle Capacity Weight for Example 2 1 000 Ibs 453 kg Example 1 Loading Your Vehicle Vehicle Capacity Weight for Example 1 1 000 554458 Ko Subtract Occupant Weight 150 Ibs 750 Ibs 340 kg 68 kg x5 Available Cargo Weight 250 Ibs 113 kg Subtract Occupant Weight 150 Ibs 300 Ibs 136 kg 68 kg x 2 Available Occupant and Cargo Weight 700 Ibs 317 kg 4 38 Example 3 Loading Your Vehicle item Description Toa A Vehicle Capacity Weight 1 000 Ibs for Example 3 453 kg Subt
299. ome pressure left 5 32 2 Then keep turning the pressure cap but now push down as you turn it Remove the pressure cap You can be burned if you spill coolant on hot engine parts Coolant contains ethylene glycol and it will burn if the engine parts are hot enough Do not spill coolant on a hot engine Housing Bypass Tube After the engine cools open the coolant air bleed valves There are two bleed valves One is located on the thermostat housing The other is located on the thermostat bypass tube 4 Fill the radiator with the proper DEX COOL coolan mixture up to the base of the filler neck See Cooland on page 5 22 for more information about the proper coolant mixture If you see a stream of coolant coming from an air bleed valve close the valve Otherwise close the valves after the radiator is filled 5 Rinse or wipe any spilled coolant from the engine and the compartment 5 33 5 34 Start the engine and let it run until you can feel the upper radiator hose getting hot Watch out for the engine cooling fans By this time the coolant level inside the radiator filler neck may be lower If the level is lower add more of the proper DEX COOL coolant mixture through the filler neck until the level reaches the base of the filler neck Edy 0 b dI 3 S a KS 8 Then replace the pressure cap At any time during this procedure if coolant begins to flow
300. ompact spare tire and disable the all wheel drive system The AWD DISABLE message will come on the instrument panel cluster indicating that the all wheel drive system is off You may detect a slight pull during this time but this is normal Notice You may damage your vehicle s all wheel drive system if your vehicle is driven for an extended period with a compact spare tire installed and the all wheel drive system in operation See All Wheel Drive System and AWD Disable Warning Message in the Index for more information Appearance Care Remember cleaning products can be hazardous Some are toxic Others can burst into flames if you strike a match or get them on a hot part of the vehicle Some are dangerous if you breathe their fumes in a closed space When you use anything from a container to clean your vehicle be sure to follow the manufacturer s warnings and instructions And always open your doors or windows when you are cleaning the inside Never use these to clean your vehicle Gasoline Benzene Naphtha Carbon Tetrachloride Acetone Paint Thinner e Turpentine Lacquer Thinner Nail Polish Remover They can all be hazardous some more than others and they can all damage your vehicle too Do not use any of these unless this manual says you can In many uses these will damage your vehicle Alcohol e Laundry Soap Bleach e Reducing Agents Cleaning the Inside of Your Vehi
301. onditions on specified government test surfaces of asphalt and concrete A tire marked C may have poor traction performance Warning The traction grade assigned to this tire is based on straight ahead braking traction tests and does not include acceleration cornering hydroplaning or peak traction characteristics Temperature A B C The temperature grades are A the highest B and C representing the tire s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel Sustained high temperature can cause the material of the tire to degenerate and reduce tire life and excessive temperature can lead to sudden tire failure The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No 109 Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law Warning The temperature grade for this tire is established for a tire that is properly inflated and not overloaded Excessive speed underinflation or excessive loading either separately or in combination can cause heat buildup and possible tire failure Wheel Alignment and Tire Balance The wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance Scheduled wheel alignme
302. one or more of these conditions In heavy city traffic where the outside temperature regularly reaches 90 F 32 or higher In hilly or mountainous terrain When doing frequent trailer towing Uses such as found in taxi police or delivery service i Drain flush and refill cooling system See Eroma on page 5 22 for what to use Inspect hoses ean radiator condenser pressure cap and filler neck Pressure test the cooling system and pressure cap j A fluid loss in any vehicle system could indicate a problem Have the system inspected and repaired and the fluid level checked Add fluid if needed Owner Checks and Services These owner checks and services should be performed at the intervals specified to help ensure the safety dependability and emission control performance of your vehicle Your GM Goodwrench dealer can assist you with these checks and services Be sure any necessary repairs are completed at once Whenever any fluids or lubricants are added to your vehicle make sure they are the proper ones as shown in Recommended Fluids and Lubricants on page 6 12 At Each Fuel Fill It is important to perform these underhood checks at each fuel fill Engine Oil Level Check Check the enging_gil level and add the proper oil if necessary See on page 5 13 for further details Notice It is important to check your oil regularly and keep it at the proper level Failure to keep your engine oil at the proper
303. ood CD If any error occurs repeatedly or if an error cannot be corrected contact your dealer If your radio displays an error message write it down and provide it to your dealer when reporting the problem Radio with CD MP3 Yaeeine G FRE REE Radio Data System RDS Your audio system is equipped with a Radio Data System RDS RDS features are available for use only on FM stations that broadcast RDS information With RDS your radio can do the following Seek to stations broadcasting the selected type of programming e Receive announcements concerning local and national emergencies Display messages from radio stations Seek to stations with traffic announcements This system relies upon receiving specific information from these stations and will only work when the information is available In rare cases a radio station may broadcast incorrect information that will cause the radio features to work improperly If this happens contact the radio station While you are tuned to an RDS station the station name or the call letters will appear on the display instead of the frequency RDS stations may also provide the time of day a program type PTY for current programming and the name of the program being broadcast XM Satellite Radio Service 48 Contiguous US States XM is a continental U S based satellite radio service that offers 100 coast to coast channels including music news sports ta
304. oplaning The best advice is to slow down when it is raining 4 21 Driving Through Deep Standing Water Notice If you drive too quickly through deep puddles or standing water water can come in through your engine s air intake and badly damage your engine Never drive through water that is slightly lower than the underbody of your vehicle If you can not avoid deep puddles or standing water drive through them very slowly Driving Through Flowing Water Flowing or rushing water creates strong forces If you try to drive through flowing water as you might at a low water crossing your vehicle can be carried away As little as six inches of flowing water can carry away a smaller vehicle If this happens you and other vehicle occupants could drown Do not ignore police warning signs and otherwise be very cautious about trying to drive through flowing water 4 22 Some Other Rainy Weather Tips Besides slowing down allow some extra following distance And be especially careful when you pass another vehicle Allow yourself more clear room ahead and be prepared to have your view restricted by road spray Have good tires with proper tread depth See Tires on page 5 58 City Driving One of the biggest problems with city streets is the amount of traffic on them You will want to watch out for what the other drivers are doing and pay attention to traffic signals Here are ways to increase your safety in city drivi
305. or sound 3 114 Recommended Action When return to the DVD from the system menu sometimes it plays from the beginning and sometimes from where it left off The fast forward reverse revious and next unctions do not work If the stop button was pressed once it resumes pay y from where it left off f the stop button was pressed twice it will start at the beginning of the DVD However if a change was made to the menu the DVD will start from where it left off even if the stop button was only pressed once Some commands that do one thing for DVDs will not always work or erform the same function or audio CDs or games These functions may also be disabled when the DVD is playing the copyright information or previews Recommended Action My disc is stuck in the player The eject button does not work Press the eject button on the DVD player Turn the power off then on again then press the eject button on the DVD player Do not attempt to force or remove the disc from the player If the problem persists return to your dealer for further assistance I lost the remote control Contact your dealer for and or the headphones assistance What is the best way to Wipe the video screen clean the screen with a soft cloth that is slightly damp with water Sometimes the cordless headphone audio cuts out or buzzes for a moment then it comes back This could be caused by interference from cell t
306. or push the SELECT knob to store the equalization setting and the number You will hear a beep and EQ SAVED will appear on the display 6 Repeat the steps for the other EQ settings and numbers EQ 5 has been programmed at the factory for use with talk radio but it can be set to a different tone 3 77 Adjusting the Speakers Balance Fade BAL Balance To adjust the balance between the right and the left speakers press and release this button until BAL appears on the display The SELECT LED indicator will light to show that the speakers can be adjusted Turn the SELECT knob to move the sound toward the right or the left speakers FADE To adjust the fade between the front and the rear speakers press and release this button until FADE appears on the display The SELECT LED indicator will light to show that the speakers can be adjusted Turn the SELECT knob to move the sound toward the front or the rear speakers Pressing and holding the BAL FADE button for two seconds will return all speaker settings to the middle position Finding a Program Type PTY Station RDS and XM To select and find a desired PTY perform the following 1 Press PROG TYPE to activate program type select mode The PTY symbol will appear on the display 2 Turn the SELECT knob to select a PTY 3 78 3 Once the desired PTY is displayed press either SEEK arrow to select the PTY and take you to the PTY s first station 4 If you want t
307. oss could indicate a problem check and have it repaired if needed What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use See Recommended Fluids and Lubricants on page 6 12 Bulb Replacement Halogen Bulbs For the type of bulbs see Replacement Bulbs on page 5 55 For any bulb changing procedure not listed in this section contact your dealer Fr Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb You or others could be injured Be sure to read and follow the instructions on the bulb package 5 50 Headlamps 1 Open the hood 2 Push in on the headlamp and lift up the headlamp retaining clip partway but do not remove 3 Unsnap the headlamp assembly by pulling it forward away from the vehicle 4 Disconnect the electrical connector by pulling back on the locking tab located on the electrical connector to separate the two connectors 5 Remove the bulb access cover 6 Turn the bulb socket one quarter of a turn clockwise 7 Pull the bulb assembly out from the lamp housing 5 51 11 Reinstall the bulb access cover making sure it is in place 12 Align the retaining clips on the back of the headlamp with the rectangular holes in the mounting panel 13 Push firmly on both ends of the headlamp to snap it into position 14 Push the retaining clip down to its original position 8 Unhook the electrical con
308. otated every 5 000 to 8 000 miles 8 000 to 13 000 km Any time you notice unusual wear rotate your tires as soon as possible and check wheel alignment Also check for damaged tires or wheels See on page 5 70 and Wheel Replacemen on page 5 74 for more information Make sure the spare tire is stored securely Push pull and then try to rotate or turn the tire If it moves use the folding wrench to tighten the cable See Storing a Flat or Spare Tire and Tools in Changing a Fla on page 5 78 The purpose of regular rotation is to achieve more uniform wear for all tires on the vehicle The first rotation is the most important See Scheduled Maintenance on page 6 4 for scheduled rotation intervals When rotating your tires always use the correct rotation pattern shown here Don t include the compact spare tire in your tire rotation After the tires have been rotated adjust the front and rear inflation pressures as shown on the Certification Tire label or the Tire and Loading Information label Reset the check tire pressure system if equipped See Check Tire Pressure System on page 5 67 Make certain that all wheel nuts are properly tightened See Wheel Nut Torque under Capacities and Specifications on page 5 118 Rust or dirt on a wheel or on the parts to which it is fastened can make wheel nuts become loose after a time The wheel could come off and cause an accident When you change a whe
309. our Engine Move your shift lever to PARK P or NEUTRAL N Your engine won t start in any other position that s a safety feature To restart when you re already moving use NEUTRAL N only Notice Shifting into PARK P with the vehicle moving could damage the transaxle Shift to PARK P only when your vehicle is stopped 1 With your foot off the accelerator pedal turn your ignition key to START When the engine starts let go of the key The idle speed will go down as your engine warms up Notice Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner And the excessive heat can damage your starter motor Wait about 15 seconds between each try to help avoid draining your battery or damaging your starter 2 If the engine doesn t start in 10 seconds push the accelerator pedal about one quarter of the way down while you turn the key to START Do this until the engine starts As soon as it does let go of the key 2 20 3 If your engine still won t start or starts but then stops it could be flooded with too much gasoline Try pushing your accelerator pedal all the way to the floor and holding it there as you hold the key in START for a maximum of 15 seconds This clears the extra gasoline from the engine If the engine still won t start or starts briefly but then stops again repeat Step 1 or 2 depending on the temperature When the engine starts release t
310. our engine coolant has overheated If you have been operating your vehicle under normal driving conditions you should pull off the road stop your vehicle and turn off the engine as soon as possible See Engine Overheating on page 5 25 Charging System Indicator Message The charging system battery symbol will come on in the message center when you turn on the ignition as a check to show you it is working It will remain on as long as the engine is not running It should go out once the engine is running If it stays on or comes on while you are driving you may have a problem with the charging system It could indicate that you have problems with a generator drive belt or another electrical problem Have it checked right away Driving while this indicator appears in the message center could drain your battery If you must drive a short distance with the message on be certain to turn off all your accessories such as the radio and air conditioner Low Oil Pressure Message LOW OIL PRESSURE United States Canada Your vehicle is equipped with a low oil pressure warning message Your oil pressure message lets you know when you may have a problem with your engine oil pressure 3 45 When the engine is running and this message appears the engine oil level may be too low There may also be another problem causing low oil pressure Do not keep driving if the oil pressure is low If you do your engine can b
311. owers or by using your cellular telephone or other radio transmitter device in the vehicle Recommended Action DVD System inoperable The cordless headphones have audio distortion In auxiliary mode the picture moves or scrolls In severe or extreme temperatures your DVD system might not be operable Temperatures below 4 F 20 C or above 140 F 60 C could damage your DVD system Please operate your DVD system under normal or comfortable cabin temperature ranges Verify that the headphones are facing to the front of the vehicle left and right sides are indicated on the headphones to ensure that the signal is received properly Check the signal coming from the auxiliary device and make sure that the connection and the signal are good 3 115 Rear Audio Controller RAC PRESET MUTE If your vehicle has this option you can control certain radio functions using the buttons on your Rear Audio Controller RAC A SEEK V Press the up or the down arrow to tune to the next or the previous radio station If a CD is playing the player will advance with the up arrow and reverse with the down arrow BAND Press this button to choose FM1 FM2 AM or XM1 or XM2 48 contiguous US states if equipped Press this button when a CD is playing to listen to the radio The inactive CD will remain safely inside the radio for future listening 3 116 PRESET Press this button to go to a station you h
312. owing a trailer reduce the amount of cargo being hauled as soon as it is possible If the light stops flashing and remains on steady see If the Light Is On Steady following If the light continues to flash when it is safe to do so stop the vehicle Find a safe place to park your vehicle Turn the key off wait at least 10 seconds and restart the engine If the light remains on steady see If the Light Is On Steady following If the light is still flashing follow the previous steps and see your dealer for service as soon as possible If the Light Is On Steady You may be able to correct the emission system malfunction by considering the following Did you recently put fuel into your vehicle If so reinstall the fuel cap making sure to fully install the cap See Filing Your Tani on page 5 7 The diagnostic system can determine if the fuel cap has been left off or improperly installed A loose or missing fuel cap will allow fuel to evaporate into the atmosphere A few driving trips with the cap properly installed should turn the light off Did you just drive through a deep puddle of water If so your electrical system may be wet The condition will usually be corrected when the electrical system dries out A few driving trips should turn the light off Have you recently changed brands of fuel lf so be sure to fuel your vehicle with quality fuel See on page 5 4 Poor fuel quality will cause your engine no
313. own brakes and they must be adequate Be sure to read and follow the instructions for the trailer brakes so you will be able to install adjust and maintain them properly Because your vehicle may have anti lock brakes do not try to tap into your vehicle s brake system If you do both brake systems will not work well or at all 4 45 Driving with a Trailer If you have a rear most window open and you pull a trailer with your vehicle carbon monoxide CO could come into your vehicle You can not see or smell CO It can cause unconsciousness or death See Engine on page 2 29 To maximize your safety when towing a trailer 4 46 Have your exhaust system inspected for leaks and make necessary repairs before starting on your trip Keep the rear most windows closed If exhaust does come into your vehicle through a window in the rear or another opening drive with your front main heating or cooling system on and with the fan on any speed This will bring fresh outside air into your vehicle Do not use the climate control setting for maximum air because it only recirculates the air inside your vehicle See Climate Control System in the Index Towing a trailer requires a certain amount of experience Before setting out for the open road you will want to get to know your rig Acquaint yourself with the feel of handling and braking with the added weight of the trailer And always keep in mind that the vehicle you are
314. painted surfaces on your vehicle This damage can take two forms blotchy ring shaped discolorations and small irregular dark spots etched into the paint surface Although no defect in the paint job causes this GM will repair at no charge to the owner the surfaces of new vehicles damaged by this fallout condition within 12 months or 12 000 miles 20 000 km of purchase whichever occurs first 5 109 Vehicle Care Appearance Materials C Desorption Usage See your GM dealer for more information on purchasing 7 mii the following products i emoves swirl marks Tine SAG Swirl Remover Polish scratches and other light surface contamination pesaription usage Removes light scratches Polishing Cloth Interior and exterior and protects finish Wax Treated polishing cloth Cl eans shines and Tar and Road Oil Removes tar road oil and Pras Tire Shine Low protects in one easy step Remover asphalt no wiping necessary Chrome Cleaner and Use on chrome or Medium foaming Polish stainless steel shampoo Cleans and White Sidewall Tire Removes soil and black Wash Wax Concentrate lightly waxes Cleaner marks from whitewalls Biodegradable and from carpets vinyl and Removes dirt grime Glass Cleaner smoke and fingerprints cloth upholstery R ditt and an Odorless spray odor Chrome and Wire Wheel SeA ig S Ea Odor Eliminator eliminator used on fabrics Cleaner TOM CALOME Wiese an vinyl leather and carpet
315. particular crash no one can say whether an air bag should have inflated simply because of the damage to a vehicle or because of what the repair costs were For frontal air bags inflation is determined by the angle of the impact and how quickly the vehicle slows down in frontal and near frontal impacts For side impact air bags inflation is determined by the location and severity of the impact 1 67 What Makes an Air Bag Inflate In an impact of sufficient severity the air bag sensing system detects that the vehicle is in a crash For both frontal and side impact air bags the sensing system triggers a release of gas from the inflator which inflates the air bag The inflator the air bag and related hardware are all part of the air bag modules Frontal air bag modules are located inside the steering wheel and instrument panel For vehicles with side impact air bags the air bag modules are located in the seatback closest to the driver s and or right front passenger s door How Does an Air Bag Restrain In moderate to severe frontal or near frontal collisions even belted occupants can contact the steering wheel or the instrument panel In moderate to severe side collisions even belted occupants can contact the inside of the vehicle The air bag supplements the protection provided by safety belts Air bags distribute the force of the impact more evenly over the occupant s upper body stopping the occupant more gradually But the
316. play Mode Then select Full This will fill the screen If there are borders on the top and bottom the movie may have been made that way for a standard screen Eject the disc again Press the main menu button on the DVD player or the remote control and change the audio or language selection on the DVD menu Point the remote control directly at the transmitter window The batteries could be weak or put in wrong The parental control button might have been pressed The power indicator light will flash 3 113 Recommended Action How do get subtitles on Press the subtitle button or off on the remote control to go to the DVDs main menu Then follow the screen prompts After stopping the player I Press the stop button on push the play button but the remote control to sometimes the DVD starts resume where the DVD where left off and left off Press the stop sometimes at the button twice to start the beginning DVD at the beginning If the power is off and the DVD is still in the player press the play button Press and release the SRCE button on the remote control or the DVD player to get to auxiliary input Check to make sure that the auxiliary source is connected to the inputs properly The audio or video skips The DVD could be dirty or or jumps scratched Try cleaning the DVD The DVD is playing but there is no picture or sound The auxiliary source is running but there is no picture
317. press and hold the SET button while the average speed is displayed on the DIC and until the speed resets to your current speed OIL LIFE LEFT HOLD SET TO RESET This message displays the current percentage of the oil life by the GM Oil Life System To reset the oil life press and hold the SET button while this message is displayed When the system is reset 100 will be displayed and the CHANGE ENGINE OIL message on the message center will go off 3 56 TIRE PRESSURE The check tire pressure system can alert you to a large change in the pressure of one tire You must begin driving before the system will detect a low tire pressure USE SET TO SELECT ENGLISH METRIC You can use this display to select English or metric Press the SET button to toggle between English or metric The odometer trip odometer and head up display HUD if equipped will also change A Canadian odometer and trip odometer will remain in metric units only OFF No driver information will be displayed in this mode If the DIC is left in this mode for more than three seconds the display will turn off Press the MODE button to start the DIC DIC Vehicle Personalization The DIC is used to program the choices of two drivers The drivers are recognized as DRIVER 1 or DRIVER 2 on the DIC display You will let the DIC know which driver you are by using your remote keyless entry transmitter Each remote keyless entry transmitter was pre programmed to belong to D
318. quipped by performing the following steps 1 Turn the radio on 2 Press BAND to select FM1 FM2 AM or XM1 or XM2 3 Tune in the desired station 4 Press EQ to select the equalization 5 Press and hold one of the six numbered pushbuttons until you hear a beep Whenever you press that numbered pushbutton the station you set will return and the equalization that you selected will be automatically stored for that pushbutton 6 Repeat the steps for each pushbutton Setting the Tone Bass Treble TONE Press and release this button until BASS MID or TREB appears on the display The SELECT LED indicator will light to show that the tone control can be adjusted Turn the SELECT knob to increase or to decrease If a station is weak or noisy you may want to decrease the treble Pressing and holding the TONE button until FLAT appears on the display will return all of the tone controls to the middle position EQ Equalizer Press this button to select customized bass midrange and treble equalization settings You can set up to six customized equalization settings by performing the following steps 1 Turn the radio on 2 Use the TONE button and the SELECT knob to create the desired equalization 3 Press and hold the EQ button for two seconds SELECT EQ will appear on the display and the EQ symbol will flash 4 Press EQ or turn the SELECT knob to select the desired EQ number 5 Press and hold the EQ button
319. r and an auxiliary source Main Menu Press this button to view the media menu The media menu is different on every DVD Use the up down right and left arrow buttons to move the cursor around the media menu After making a selection press enter This button only operates when using a DVD db Power Press this button to turn the DVD player on and off 0 Power Light Shows if power is on or off O Stop Press this button to stop playing rewinding or fast forwarding Press this button twice to return to the beginning of the DVD gt Play Pause Press this button to start play of a DVD or CD Press this button while a DVD or CD is playing to pause it Press it again to continue play of a DVD or CD LJ Display Control Button Press this button to adjust color tint brightness contrast and display mode normal full or Zoom The dynamic range compression feature can be used to reduce the loud audio produced by some DVDs and to improve the audio quality A Pl vid lt 4 gt Directional Control Circle Press these buttons to move through menu choices or to move forward or back in a movie These controls can be used to move forward or backward through a CD 4 Enter Press this button to select choices highlighted in any menu Parental Control Button This button is located behind the video screen next to the auxiliary jacks near the driver of the vehicle Press this button while a
320. r audio system has been designed to operate easily and to give years of listening pleasure You will get the most enjoyment out of it if you acquaint yourself with it first Figure out which radio you have in your vehicle find out what your audio system can do and how to operate all of its controls to be sure you re getting the most out of the advanced engineering that went into it Your vehicle has a feature called Retained Accessory Power RAP With RAP you can play your audio system even after the ignition is turned off_See Retained Accessory Power RAP under on page 2 18 3 64 Setting the Time Your radio may have a button marked with an H or HR to represent hours and an M or MIN to represent minutes Press and hold the hour button until the correct hour appears on the display AM will appear for morning hours Press and hold the minute button until the correct minute appears on the display The time may be set with the ignition on or off To synchronize the time with an FM station broadcasting Radio Data System RDS information press and hold the hour and minute buttons at the same time until UPDATED appears on the display If the time is not available from the station NO UPDATE will appear on the display RDS time is broadcast once a minute Once you have tuned to an RDS broadcast station it may take a few minutes for your time to update Radio with CD Base Level Radio Data System RDS Your au
321. r future listening A SEEK V Press the up or the down arrow to tune to the next or to the previous radio station If a CD is playing the tape or the CD will advance with the up arrow and reverse with the down arrow A voL Y Volume Press the up or the down arrow to increase or to decrease volume PLAY Press this button to play a CD when listening to the radio MUTE Press this button to silence the system Press it again or any other radio button to turn on the sound 3 117 DVD Distortion You may experience video distortion when operating cellular phones scanners CB radios Global Position Systems GPS two way radios mobile fax or walkie talkies It may be necessary to turn off the DVD player when operating one of these devices in or near the vehicle Excludes the OnStar System Understanding Radio Reception AM The range for most AM stations is greater than for FM especially at night The longer range however can cause stations to interfere with each other AM can pick up noise from things like storms and power lines Try reducing the treble to reduce this noise FM Stereo FM stereo will give you the best sound but FM signals will reach only about 10 to 40 miles 16 to 65 km Tall buildings or hills can interfere with FM signals causing the sound to come and go 3 118 XM Satellite Radio Service 48 Contiguous US States XM Satellite Radio gives you digital radio reception from
322. r on the display go back to Step 1 If both PTY and TRAF are on the radio will search for stations with the selected PTY and traffic announcements SCAN You can scan the stations within a PTY by performing the following 1 Press PROG TYPE to activate program type select mode The PTY symbol will appear on the display 2 Turn the SELECT knob to select a PTY 3 Once the desired PTY is displayed press and hold either SCAN arrow and the radio will begin scanning the stations in the PTY 4 Press either SCAN arrow to stop at a station lf both PTY and TRAF are on the radio will scan for stations with the selected PTY and traffic announcements BAND Alternate Frequency Alternate frequency allows the radio to switch to a stronger station with the same programming To turn alternate frequency on press and hold BAND for two seconds AF ON will appear on the display The radio may switch to stronger stations To turn alternate frequency off press and hold BAND again for two seconds AF OFF will appear on the display The radio will not switch to other stations This function does not apply for XM Satellite Radio Service Setting Preset PTYs RDS Only The six numbered pushbuttons let you return to your favorite PTYs These pushbuttons have factory PTY presets You can set up to 12 PTYs six FM1 and six FM2 by performing the following steps 1 Press PROG TYPE to activate program type select mode The PTY sym
323. r strap C 1 52 In order to use the LATCH system in your vehicle you need a child restraint designed for that system To assist you in locating the lower anchors for this child restraint system each seating position with the LATCH system has a label on the seatback The labels are located at each lower anchor position near the base of the rear seat outside passenger positions If a LATCH type child restraint isn t attached to its anchorage points the restraint won t be able to protect a child sitting there In a crash the child could be seriously injured or killed Make sure that a LATCH type child restraint is properly installed using the anchorage points or use the vehicle s safety belts to secure the restraint See Securing a Child Restraint in a Rear Outside Seat Position in the Index for information on how to secure a child restraint in your vehicle using the vehicle s safety belts 1 53 Securing a Child Restraint Designed for the LATCH System 1 Find the anchors for the seating position you want to use where the bottom of the seatback meets the back of the seat cushion 2 Put the child restraint on the seat 3 Attach the anchor points on the child restraint to the anchors in the vehicle The child restraint instructions will show you how 4 If the child restraint is forward facing attach the top strap to the top strap anchor See Tap Strapon page 1 49 Tighten the top str
324. r to the ground continue with Step 4 under Removing the Spare Tire Vehicles without the Sliding Rear Convenience Tray earlier in this section 5 If you still cannot lower the spare tire to the ground see Secondary Latch System later in this section Removing the Spare Tire Vehicles with the Sliding Rear Convenience Tray The compact spare tire is located under the vehicle ahead of the rear bumper Use the spare tire hoist to raise lower and store the compact spare See Compact Spare Tire on page 5 102 for more information about the compact spare 3 You will hear a click when the sliding rear tray is locked into the extended position This is where the sliding rear tray needs to be in order to be able to remove the compact spare tire 4 Open the driver s side storage compartment door of the sliding rear tray 5 Remove the cap on the bottom of the storage compartment and flip the carpet cut out to expose the hoist shaft 6 Remove the extension tube that is attached at the front of the storage compartment 7 Insert one end of the extension tube to the hoist shaft and attach the folding wrench to the other end of the extension tube A P aa Tra E Retainer f 8 Turn the folding wrench counterclockwise to lower Y F Compact Spare Tire the spare tire to the ground Continue turning the B Storage G Spring wrench until the spare tire can be pulled out Compartment H Hoist Shaft from under the vehicle
325. r vehicle in good condition be sure to maintain your vehicle properly Using Your Maintenance Schedule We at General Motors want to help you keep your vehicle in good working condition But we do not know exactly how you will drive it You may drive very short distances only a few times a week Or you may drive long distances all the time in very hot dusty weather You may use your vehicle in making deliveries Or you may drive it to work to do errands or in many other ways Because of all the different ways people use their vehicles maintenance needs vary You may need more frequent checks and replacements So please read the following and note how you drive If you have any questions on how to keep your vehicle in good condition see your GM Goodwrench dealer This schedule is for vehicles that e carry passengers and cargo within recommended limits You will find these limits on the tire and loading information label See Loading Your Vehicle on page 4 36 e are driven on reasonable road surfaces within legal driving limits e use the recommended fuel See Gasoline Octane on page 5 4 The services in Seeded Maninang page 6 4 should be performed when indicated See Additional on page 6 6 and on page 6 7 for further information Performing maintenance work on a vehicle can be dangerous In trying to do some jobs you can be seriously injured Do your own maintenance work only if you have the require
326. ract Occupant 1 000 Ibs 453 kg 0 Ibs 0 kg Refer to your vehicle s tire and loading information label for specific information about your vehicle s capacity weight and seating positions The combined weight of the driver passengers and cargo should never exceed your vehicle s capacity weight Weight 200 Ibs 91 kg x5 Available Cargo Certification Tire Label GAWR FRT GAWR RR COLD TIRE PRESSURE Ll I SEE OWNER S MANUAL FOR ADDITIONAL INFORMATION The Certification Tire label is found on the rear edge of the driver s door The label shows the size of your original tires and the inflation pressures needed to obtain the gross weight capacity of your vehicle This is called the Gross Vehicle Weight Rating GVWR The GVWR includes the weight of the vehicle all occupants fuel and cargo 4 39 The Certification Tire label also tells you the maximum weights for the front and rear axles called the Gross Axle Weight Rating GAWR To find out the actual loads on your front and rear axles you need to go toa weigh station and weigh your vehicle Your dealer can help you with this Be sure to spread out your load equally on both sides of the centerline Never exceed the GVWR for your vehicle or the GAWR for either the front or rear axle 4 40 Do not load your vehicle any heavier than the GVWR or either the maximum front or rear GAWR If you do parts on your vehicle can break and it can change
327. re On hot days open the windows to let hot inside air escape then close them This helps to reduce the time it takes for your vehicle to cool down It also helps the system to operate more efficiently For quick cool down on hot days do the following 1 Select the vent mode 2 Select the coolest temperature 3 Select the highest fan speed 4 Select A C 5 Select the recirculation mode Using these settings together for long periods of time may cause the air inside of your vehicle to become too dry To prevent this from happening after the air inside of your vehicle has cooled turn the recirculation mode off The air conditioning system removes moisture from the air so you may sometimes notice a small amount of water dripping underneath your vehicle while idling or after turning off the engine This is normal Defogging and Defrosting Fog on the inside of windows is a result of high humidity or moisture condensing on the cool window glass This can be minimized if the climate controls system is used properly There are two modes to clear fog or frost from your windshield Use the defog mode to clear the windows of fog or moisture and warm the passengers Use the defrost mode to remove fog or frost from the windshield more quickly Turn the right knob to select the defog or defrost mode N j Defog This mode directs air to the windshield and the floor outlets When you select this mode the system turns off rec
328. re necessary to help prevent brake pulsation When tires are rotated inspect brake pads for wear and evenly tighten wheel nuts in the proper sequence to GM torque specifications Brake linings should always be replaced as complete axle sets Brake Pedal Travel See your dealer if the brake pedal does not return to normal height or if there is a rapid increase in pedal travel This could be a sign of brake trouble Brake Adjustment Every time you apply the brakes with or without the vehicle moving your brakes adjust for wear Replacing Brake System Parts The braking system on a vehicle is complex Its many parts have to be of top quality and work well together if the vehicle is to have really good braking Your vehicle was designed and tested with top quality GM brake parts When you replace parts of your braking system for example when your brake linings wear down and you need new ones put in be sure you get new approved GM replacement parts If you do not your brakes may no longer work properly For example if someone puts in brake linings that are wrong for your vehicle the balance between your front and rear brakes can change for the worse The braking performance you have come to expect can change in many other ways if someone puts in the wrong replacement brake parts Battery Your new vehicle comes with a maintenance free ACDelco battery When it is time for a new battery get one that has the replaceme
329. re that they are installed correctly using the diagram on the inside of the battery compartment 3 Tighten the screw on the battery compartment door If the headphones are to be stored for a long period of time remove the batteries and keep them in a cool dry place Stereo RCA Jacks The RCA jacks are located behind the video screen on the DVD console The RCA jacks allow you to connect audio and video signals from an auxiliary device such as a camcorder or a video game unit to your RSE The yellow RCA jack is used for video the red RCA jack for right audio and the white RCA jack for left audio inputs The system requires standard RCA cables not included to connect your auxiliary device to the RCA jacks Refer to the manufacturer s instructions for proper usage 3 104 To use the auxiliary audio and video inputs on the entertainment system connect an external auxiliary device such as a camcorder to the RCA jacks and turn on both the auxiliary device power and the power on the front of the RSE player If a disc is present when the RSE power is turned on the player will automatically begin playing the disc and the user will need to press the SRCE button on the remote control or on the DVD player faceplate to toggle the system between the DVD player and the auxiliary device See DVD Player and Remote Control later in this section for more information Audio Speakers Audio from the DVD player or auxiliary de
330. rear blowout particularly on a curve acts much like a skid and may require the same correction you d use in a skid In any rear blowout remove your foot from the accelerator pedal Get the vehicle under control by steering the way you want the vehicle to go It may be very bumpy and noisy but you can still steer Gently brake to a stop well off the road if possible Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training The jack provided with your vehicle is designed only for changing a flat tire If it is used for anything else you or others could be badly injured or killed if the vehicle slips off the jack Use the jack provided with your vehicle only for changing a flat tire If a tire goes flat the next part shows how to use your jacking equipment to change a flat tire safely 5 78 Changing a Flat Tire If a tire goes flat avoid further tire and wheel damage by driving slowly to a level place Turn on your hazard warning flashers Changing a tire can cause an injury The vehicle can slip off the jack and roll over you or other people You and they could be badly injured Find a level place to change your tire To help prevent the vehicle from moving 1 Set the parking brake firmly 2 Put the shift lever in PARK P 3 Turn off the engine To be even more certain the vehicle won t move you can put blocks at the front and rear
331. rear convenience tray may cause damage Repairs would not be covered by your warranty Do not load heavy objects on the sliding rear convenience tray Rear Storage Area There are four small storage compartments in the rear of your vehicle One is on the passenger s side two are on the driver s side and one is on the floor by the tailgate To remove the covers lift up on the tabs If your vehicle has the 10 speaker system the compartment on the passenger s side and the long compartment on the driver s side will be equipped with speakers 2 37 Roof Rack System If you try to carry something on top of your vehicle that is longer or wider than the luggage carrier like paneling plywood a mattress and so forth the wind can catch it as you drive along This can cause you to lose control What you are carrying could be violently torn off and this could cause you or other drivers to have a collision and of course damage your vehicle You may be able to carry If you have the luggage carrier you can load things on something like this inside But never carry top of your vehicle If you do load things on the top of your something longer or wider than the luggage vehicle you must load them on the luggage carrier carrier on top of your vehicle crossrails The luggage carrier has four tie down loops on the inside of each right and left side rail These let you secure cargo placed on the crossrails as long as they are not w
332. repeat this only when you feel really uncomfortable from the cold But do it as little as possible Preserve the fuel as long as you can To help keep warm you can get out of the vehicle and do some fairly vigorous exercises every half hour or so until help comes If You Are Stuck In Sand Mud Ice or Snow In order to free your vehicle when it is stuck you will need to spin the wheels but you don t want to spin your wheels too fast The method known as rocking can help you get out when you re stuck but you must use caution If you let your tires spin at high speed they can explode and you or others could be injured And the transaxle or other parts of the vehicle can overheat That could cause an engine compartment fire or other damage When you are stuck spin the wheels as little as possible Do not spin the wheels above 35 mph 55 km h as shown on the speedometer Notice Spinning your wheels can destroy parts of your vehicle as well as the tires If you spin the wheels too fast while shifting your transaxle back and forth you can destroy your transaxle See Rocking Your Vehicle To Get It Out For information about using tire chains on your vehicle see on page 5 75 Rocking Your Vehicle To Get It Out First turn your steering wheel left and right That will clear the area around your front wheels If your vehicle has traction control you should turn your traction control system off See Trac
333. rming with the Remote Keyless Entry Ail Bag SYSIOMS iniinis eai 1 61 Transmitter 2 02 cece eee eeeeeeeeeeeeeeeeeecueeeeeeeeeeaes 2 15 How Does an Air Bag Restrain 2 1 68 Ashtrays ooo cece ee eeeeeeeeeeeeeeeeeeeteeeeeeteeeeetennneneees 3 23 Servicing Your Air Bag Equipped Vehicle 1 71 Audio Speakers 0 cece eccceccseceseeeeueeeeeeaeeeaes 3 104 What Makes an Air Bag Inflate 1 68 Audio System S cceeeeeeeeceeeeeeeeeeeeeeeeeeeees 3 64 What Will You See After an Air Bag Inflates 1 69 Audio Steering Wheel Controls 3 117 When Should an Air Bag Inflate 0 1 67 Care of Your CD and DVD Player 3 118 Where Are the Air Bags cceeeeeeeeeeeeees 1 64 Care of Your CDs and DVDs 0 0 08 3 118 Air Cleaner Filter Engine 0 0 ee 5 18 Integrated Windshield Antenna 5 3 119 Airbag Sensing and Diagnostic Module SDM 7 10 Radio with CD ccccceeecceeeeceeeeeeees 3 65 3 75 All Wheel Drive eeeeeeceeeeeeeeeees 5 48 5 102 Radio with Six Disc CD ccceeeeeeeeeee es 3 89 All Wheel Drive Disable Warning Message 3 49 Rear Audio Controller RAC 0 000 3 116 All Wheel Drive AWD System 0 eeeee 4 12 Setting the Time 00 cceeeeceeeeeseeeeeeeeeeeeees 3 64 AM Er eo ar Ene re eae ees 3 118 Theft Deterrent Feature
334. rol System TCS scenen hede regere 4 10 Control System Warning Light 0 3 38 Service Traction System Warning Message 3 43 Trailer BrakeS i cevsiscveveesehstecacecacessauateevenienaeaes 4 45 Trailer Wiring Harness ceeeeeeeeeneeeeeeeeee ee 4 49 Transaxle Fluid Automatic cccccceeeee ec ee eee eeeneeeeeees 5 20 Transaxle Operation Automatic 2 22 Transfer Case Power Transfer Unit 5 48 Transmission Transaxle Transfer Case Unit Repair Manual cy cuccccucncsateces Haba maker hals 7 13 Transportation Options cceeeeeeeeeeee teeter eens 7 8 Trip Odometer 222 aser hehe ae en 3 33 Turn and Lane Change Signals dsseeeeeree 3 8 Turn Signal Multifunction Lever u dssseeeerree 3 8 Turn Signals When Towing a Trailer 1 1W 1 1 1 1 4 47 Underhood Fuse Block sseeeeeeeeeee een tees 5 115 Understanding Radio Reception 1 3 118 Uniform Tire Quality Grading csecsenc 5 72 United States Customer Assistance 0 7 5 Unlock Feedback arne cicsaiseendassqcanadedaetes 3 62 Used Replacement Wheels W W ssseeeerrererreee 5 75 Usingsan MPS CD ieena een tien 3 84 Using Cleaner on Fabric ceeeeeeeeeeeees 5 104 Using Song List Mode cceeeeeeeeeeeeee tenes 3 101 Vehicle COMUOL am hr eia n S 4 7 Damage Warnings ceeeeeeeeeeeeee eee eeeen eens iv DO SIQM asss ia eee a
335. rom the ignition if the following conditions are met The vehicle is in PARK P The key is out of the ignition The interior lamp control is in the DOOR position All of the doors are closed After 30 seconds the interior lamps will fade out The interior lamps will fade out before 30 seconds if one of the following occurs The ignition is turned to ON LOCK is pressed on the remote keyless entry transmitter The front of the power door lock switch is pressed If your vehicle reas mi the Driver Information Center D is feature on or l program thi off See DIC Venicle EET on page 3 57 Perimeter Lighting The perimeter lighting feature will turn on the headlamps and parking lamps for 25 seconds when the following conditions are met e The ignition is turned to OFF The exterior lamp control is in the AUTO position e UNLOCK is pressed on the remote keyless entry transmitter e Itis dark enough outside After 25 seconds the headlamps and parking lamps will turn off The lamps will turn off before the 25 seconds if one of the following occurs The ignition is turned to ON The exterior lamp control is turned out of the AUTO position If your vehicle is equipped with the Driver Information Center DIC you can program this feature_on or off See Remote Lock Feedback under DIC Vehicle Personalization rsonalization on page 3 57 Front Reading Lamps There are two reading lamps locat
336. rom the windshield will stick to the wiper blades and affect their performance Clean the blade by wiping vigorously with a cloth soaked in full strength windshield washer solvent Then rinse the blade with water Check the wiper blades and clean them as necessary replace blades that look worn 5 107 Cleaning Aluminum or Chrome Plated Wheels Your vehicle may be equipped with either aluminum or chrome plated wheels Keep your wheels clean using a soft clean cloth with mild soap and water Rinse with clean water After rinsing thoroughly dry with a soft clean towel A wax may then be applied The surface of these wheels is similar to the painted surface of your vehicle Do not use strong soaps chemicals abrasive polishes abrasive cleaners cleaners with acid or abrasive cleaning brushes on them because you could damage the surface Do not use chrome polish on aluminum wheels Use chrome polish only on chrome plated wheels but avoid any painted surface of the wheel and buff off immediately after application Do not take your vehicle through an automatic car wash that has silicone carbide tire cleaning brushes These brushes can also damage the surface of these wheels 5 108 Cleaning Tires To clean your tires use a stiff brush with tire cleaner Notice Using petroleum based tire dressing products on your vehicle may damage the paint finish and or tires When applying a tire dressing always wipe off any overspray
337. rous A child can be overcome by the extreme heat and can suffer permanent injuries or even death from heat stroke Never leave a child alone in a vehicle especially with the windows closed in warm or hot weather Power Windows Switches on the driver s door armrest control each of the windows when the ignition is in ON ACCESSORY or when Retained Accessory Power is active See Retained Accessory Power RAP under gnition on page 2 18 for more information In addition each passenger s door has a window switch The driver s power window switch has two down positions Push the rear of the switch to the first position to lower the window normally Press the rear of any passenger window switch and that window will open Press the front of any switch to close the window Express Down Window The driver s window switch also has an express down feature This switch is labeled AUTO To activate the express down feature push the rear of the driver s window switch to the second position then release it The window will lower completely To stop the window while it is lowering press the front of the switch To raise the window press and hold the front of the switch Window Lock Out The drivers window controls also include a lock out switch Press the right side of the WDO LOCK switch to stop rear passengers from lowering their window The driver can still control all of the windows with the lock on Press the oth
338. rvice Vehicle Soon Message ss 3 51 Safety Belt Reminder Light 0 00 0cccceee 3 35 Program Mode Message ceeetetneteeeenteeeteees 3 51 Air Bag Readiness Light 1 3 35 Remote Keyless Entry Transmitter Battery Low Brake System Warning Light 3 36 Warning Message oa E E Aa 3 52 Anti Lock Brake System Warning Light 3 37 Parking Lamp Warning Message 0665 3 52 Traction Control System TCS Warning Light 3 38 3 1 Section 3 Instrument Panel Driver Information Center DIC 1 3 53 DIC Controls and Displays 6 eeeeeeeeee eee 3 55 DIC Vehicle Personalization eeeeeeeeees 3 57 Audio System S cceeeceeeeeeeeeeeeeeeeeen ees 3 64 Setting the Time ceeeeeeeeeeeeeeeeeeee eee nah 3 64 Radio with CD Base Level eeeeeeeeeeees 3 65 Radio with CD MP3 seeeeeeeeeeeeeeeeeee ees 3 75 Radio with Six Disc CD 226 sunde snart Dies Eben 3 89 Rear Seat Entertainment System 1 1 1 3 103 Rear Audio Controller RAC u ddsseeeeeereeee 3 116 Theft Deterrent Feature a ir 3 116 Audio Steering Wheel Controls 0055 3 117 DVD DISTOMO Mis ies aaae rate ser 3 118 Understanding Radio Reception 3 118 Care of Your CDs and DVDS 0655 3 118 Care of Your CD and DVD Player 3 118 Cleaning Your DVD Player
339. s 1 72 If the LATCH system was being used during a more severe crash you may need new LATCH system parts If belts are cut or damaged replace them Collision damage also may mean you will need to have LATCH system safety belt or seat parts repaired or replaced New parts and repairs may be necessary even if the belt or LATCH system wasn t being used at the time of the collision If an air bag inflates you ll need to replace air bag system parts See the part on the air bag system earlier in this section Section 2 Features and Controls KEYS carena HED 2 2 Parking Brake vererien 2 25 Remote Keyless Entry System eeeeeeeee 2 3 Shifting Into Park P ioc cc cies cccecseesken nian 2 26 Remote Keyless Entry System Operation 2 4 Shifting Out of Park P seeeeeeeeeeeeeees 2 28 Doors and Locks W W u sssssseeeeeeeee reen rene renee 2 7 Parking Over Things That Burn 0 2 28 Door LOCKS 0 ccecceceececeeceseuesesuesesaeseeeaeeenaes 2 7 Engine Exhaust 0cccssseee eee eeestees 2 29 Power Door Locks er ceneri 2 8 Running Your Engine While You Are Parked 2 30 Delayed LOCKING 320i raa iarann 2 8 MIOS ceisia EEA EREE 2 31 Programmable Automatic Door Locks 2 9 Manual Rearview Mirror eccerre 2 31 Rear Door Security LOCKS eseeeeeeeneeeeeeee 2 9 Outside Power Mirrors 0eeeeeeeeeeeeeeeeeees 2 31 Lockout Protection ssvar sascctane
340. s necessary for over a year However your engine oil and filter must be changed at least once a year and at this time the system must be reset Your GM Goodwrench dealer has GM trained service technicians who will perform this work using genuine GM parts and reset the system If the engine oil life system is ever reset accidentally you must service your vehicle within 3 000 miles 5 000 km since your last service Remember to reset the oil life system whenever the oil is changed See on page 5 13 for information on the Engine Oil Life System and resetting the system When the CHANGE ENGINE OIL message appears certain services checks and inspections are required Required services are described in the following for Maintenance I and Maintenance II Generally it is recommended that your first service be Maintenance I your second service be Maintenance II and that you alternate Maintenance I and Maintenance II thereafter However in some cases Maintenance II may be required more often Maintenance I Use Maintenance I if the CHANGE ENGINE OIL message comes on within ten months since vehicle was purchased or Maintenance II was performed Maintenance II Use Maintenance II if the previous service performed was Maintenance I Always use Maintenance II whenever the message comes on ten months or more since the last service or if the message has not come on at all for one year po Service Maintenance I Maint
341. s you may need to choose another station for that preset button No Info Artist Name Feature not No artist information is available at this time on this available channel Your system is working properly No Info Song Program Title not No song title information is available at this time on this available channel Your system is working properly No Info Category Name not No category information is available at this time on this available channel Your system is working properly No Info No Text Informational No text or informational messages are available at this message available time on this channel Your system is working properly Not Found No channel available for There are no channels available for the category you the chosen category selected Your system is working properly 3 96 XM Radio Messages cont d Radio Display es i XM Locked Theft lock active The XM receiver in your vehicle may have previously been in another vehicle For security purposes XM receivers cannot be swapped between vehicles If you receive this message after having your vehicle serviced check with the servicing facility Radio ID Radio ID label If you tune to channel 0 you will see this message alternating with your XM Radio 8 digit radio ID label This label is needed to activate your service channel 0 Radio ID not known should only be if hardware failure Chk XMRevr Hardware failure If this message does not clear within a s
342. s 5 36 Wheels Alignment and Tire Balance 1 5 73 Replacement crece coronna an EON se 5 74 When to Add Engine Oil W W u ssseeeeeeeererennee 5 14 When to Change Engine Oil GM Oil Life System ssrrinesniiisisriiereniseeisss 5 16 When to Check cceeeeeeeeeeeee teen renerne keen 5 66 15 When to Check and Change Automatic Transaxle Fluid 25 sr renee ber re 5 20 When to Check Power Steering Fluid 5 36 When to Inspect the Engine Air Cleaner Filter 5 18 When You Are Ready to Leave After Parking On a Hill i nean 4 49 Where to Put the Restraint eee 1 48 Why Safety Belts Work 0 ees 1 13 Window LOCK Out Sirs iiuarra ainsana iein iino ii 2 13 Windows Een EEE 2 12 POWER eroien ani eE AE aa 2 13 Windshield Washer 521522 ie EDER 3 10 FLUID E E E E E 5 36 Windshield Wiper Blade Replacement cseeeeeeeeeeeeeeeeees 5 56 FUSCS core testviestintresciisierieiveene dechiesalsinides 5 112 Windshield Wipers ceeeeeeeeeeneeeeereeeees 3 10 Winter Driving sas eden ist apicar 4 28 16 X XM Satellite Radio Antenna System 3 119 XM Satellite Radio Service 48 Contiguous US States 3 65 3 75 3 90 3 118 Y Your Driving the Road and Your Vehicle 4 2 Your Vehicle and the Environment 55 6 2
343. s 55 iia onneaan 1 6 Safety Belts cc cceceeee eee rete eee eee eee reene 1 12 Safety Belts They Are for Everyone 1 12 Questions and Answers About Safety Belts 1 17 How to Wear Safety Belts Properly 1 18 Driver POSINOMN cessi farsi cst orn aaamaadedes 1 18 Safety Belt Use During Pregnancy 0 1 26 Right Front Passenger Position 00 1 27 Rear Seat Passengers 1 28 Center Rear Passenger Position 00 1 32 Rear Safety Belt Comfort Guides for Children and Small Adults c cceeeeeeeeeeeeeeeeees 1 34 Safety Belt Extender ccceceeeeeeeeeeeeeaes 1 38 Child Restraints ccccceeeeeeeeee eee eee eee ees 1 39 Older Children essenin erin 1 39 Infants and Young Children ceeeeeeee ees 1 41 Child Restraint Systems eeeeeeeeeeee teres Where to Put the Restraint cee TOPSA ceina EE AOG LER Top Strap Anchor Location ser Lower Anchorages and Top Tethers for Children LATCH System n Securing a Child Restraint Designed for the LATCH System W sssseeeereeree rese Securing a Child Restraint in a Rear Outside Seat Position u seseneeeerereee Securing a Child Restraint in a Center Rear Seat Position 222225 vessels Securing a Child Restraint in the Right Front Seat Position a an Air Bag Systems aeee Where Are the Air Bags W Wu u u d dc cs
344. s closed all doors will lock Once delayed locking is programmed to ON you can do the following Cancel the delayed locking by pressing unlock using the power door lock switch or by fully inserting the key in the ignition e Override the delayed locking feature by pressing lock immediately using the power door lock switch Let the delayed locking feature complete the locking of the vehicle OFF The doors will always lock immediately when you lock the doors using the power door lock switch or press LOCK on the remote keyless entry transmitter Your vehicle was originally programmed to ON The mode may have been changed since then To determine the current mode or to change the mode do the following 1 Follow the instructions for Entering Programming Mode listed previously 2 Press the MODE button until DELAYED LOCKING appears on the DIC 3 Press the SET button until the arrow is before ON or OFF The mode you selected is now set You can either exit programming mode by following the instructions later in this section or program the next feature available on your vehicle Remote Door Unlock The remote door unlock feature can be programmed to one of the following modes DRIVER ALL With the first press of UNLOCK on the remote keyless entry transmitter the driver s door will unlock and with the second press of UNLOCK within five seconds of the first press all passenger s doors will unlock ALL A
345. s knob to switch between track mode folder playlist mode and time of day mode The display will show only 13 characters but there can be up to 3 pages of text If there are more than 13 characters in the song folder or playlist name pushing this knob within 2 seconds will take you to the next page of text If there are no other pages to be shown pushing this knob within 2 seconds will take you to the next display mode Track mode will display the current track number and the ID3 tag song name 3 88 Folder playlist mode will display the current folder or playlist number and the folder playlist name Time of day mode will display the time of day and the ID3 tag song name To change the default on the display push this knob until you see the display you want then hold this knob for two seconds The radio will produce one beep and the selected display will now be the default INFO Information INFO will appear on the display whenever a current track has ID3 tag information Press this button to display the artist name and album contained in the tag INFO will disappear from the display when the information in the ID3 tag has finished BAND Press this button to listen to the radio when a CD is playing The inactive CD will remain safely inside the radio for future listening CD AUX Auxiliary Press this button to play a CD when listening to the radio The CD symbol will appear on the display when a CD is loaded EJEC
346. s message is displayed when the radio has not been calibrated properly for the vehicle You must return to the dealer for service LOCKED This message is displayed when the THEFTLOCK system has locked up You must return to the dealer for service This function does not apply to XM Satellite Radio Service XM Radio Messages Radio Display sus XL Explicit Language XL on the radio display These channels or any others can be blocked at a Channels after the channel name customer s request by calling 1 800 852 XMXM 9696 indicates content with explicit language Updating encryption code The encryption code in your receiver is being updated and no action is required This process should take no longer than 30 seconds No Signal Loss of signal Your system is functioning correctly but you are ina location that is blocking the XM signal When you move into an open area the signal should return 3 95 Updating XM Radio Messages cont d Radio Display vig Loading XM Acquiring channel audio Your radio system is acquiring and processing audio and after 4 second delay text data No action is needed This message should disappear shortly CH Off Air Channel not in service This channel is not currently in service Tune to another channel CH Unavail Channel no longer This previously assigned channel is no longer assigned available Tune to another station If this station was one of your preset
347. s new it can lose air after a time Check the inflation pressure regularly It should be 60 psi 420 kPa After installing the compact spare on your vehicle you should stop as soon as possible and make sure your spare tire is correctly inflated The compact spare is made to perform well at speeds up to 65 mph 105 km h for distances up to 3 000 miles 5 000 km so you can finish your trip and have your full size tire repaired or replaced where you want Of course it s best to replace your spare with a full size tire as soon as you can Your spare will last longer and be in good shape in case you need it again Notice When the compact spare is installed don t take your vehicle through an automatic car wash with guide rails The compact spare can get caught on the rails That can damage the tire and wheel and maybe other parts of your vehicle Don t use your compact spare on other vehicles And don t mix your compact spare tire or wheel with other wheels or tires They won t fit Keep your spare tire and its wheel together 5 102 Notice Tire chains won t fit your compact spare Using them can damage your vehicle and can damage the chains too Don t use tire chains on your compact spare All Wheel Drive After installing a compact spare tire on a vehicle with all wheel drive you will need to drive with light to moderate acceleration for 10 seconds in a straight line This action will allow the vehicle to detect the c
348. s to a heavy unpainted metal engine part or to a remote negative terminal on the vehicle with the dead battery 5 45 5 46 Connect the other end of the negative cable at least 18 inches 45 cm away from the dead battery but not near engine parts that move The electrical connection is just as good there and the chance of sparks getting back to the battery is much less 10 Now start the vehicle with the good battery and run the engine for a while 11 Try to start the vehicle that had the dead battery lf it won t start after a few tries it probably needs service Notice If the jumper cables are removed in the wrong order electrical shorting may occur and damage the vehicle The repairs would not be covered by your warranty Remove the jumper cables in the correct order making sure that the cables do not touch each other or other metal Jumper Cable Removal Heavy Unpainted Metal Engine Part or Remote Negative Terminal Good Battery or Remote Positive and Remote Negative Terminals Dead Battery or Remote Positive Terminal To disconnect the jumper cables from both vehicles do the following 1 Disconnect the black negative cable from the vehicle that had the dead battery 2 Disconnect the black negative cable from the vehicle with the good battery 3 Disconnect the red positive cable from the vehicle with the good battery 4 Disco
349. safe place to do them yourself These simple defensive driving techniques could save your life Drunken Driving Death and injury associated with drinking and driving is a national tragedy It is the number one contributor to the highway death toll claiming thousands of victims every year Alcohol affects four things that anyone needs to drive a vehicle Judgment Muscular Coordination e Vision Attentiveness Police records show that almost half of all motor vehicle related deaths involve alcohol In most cases these deaths are the result of someone who was drinking and driving In recent years more than 16 000 annual motor vehicle related deaths have been associated with the use of alcohol with more than 300 000 people injured Many adults by some estimates nearly half the adult population choose never to drink alcohol so they never drive after drinking For persons under 21 it is against the law in every U S state to drink alcohol There are good medical psychological and developmental reasons for these laws The obvious way to eliminate the leading highway safety problem is for people never to drink alcohol and then drive But what if people do How much is too much if someone plans to drive It is a lot less than many might think Although it depends on each person and situation here is some general information on the problem The Blood Alcohol Concentration BAC of someone who is drinking depe
350. safety lock 2 z E F 3 Close the door 4 Repeat Steps 1 through 3 for the other rear door lock The rear doors on your vehicle cannot be opened from inside the vehicle when this feature is in use If you want to open the rear door when the security lock is on unlock the door from the inside and then open the door from the outside Canceling the Rear Door Security Locks Unlock and open the rear door from the outside Push the lever down to disengage the safety lock Close the door Repeat Steps 1 through 3 for the other rear door lock hat JE tese The rear door locks will now work normally Lockout Protection The lockout protection feature may prevent you from locking your key in your vehicle Pressing the power door lock switch will lock all doors then unlock the driver s door if the key is in the ignition when a door is opened If you leave the key in your vehicle but not in the ignition or if you use the manual door lock you could still lock the key in the vehicle Always remember to take the key with you Leaving Your Vehicle If you are leaving the vehicle take your key open your door and set the locks from the inside Then get out and close the door 2 10 Liftgate Tailgate It can be dangerous to drive with the liftgate tailgate open because carbon monoxide CO gas can come into your vehicle You can not see or smell CO It can cause unconsciousness and even death If you must drive wit
351. sappear from the display until another new message is received The old message can be displayed by pressing the INFO button You can view an old message until a new message is received or a different station is tuned to TRAF Traffic If TRAF appears on the display the tuned station broadcasts traffic announcements To receive the traffic announcement from the tuned station press this button Brackets will be displayed around TRAF and when a traffic announcement comes on the tuned radio station you will hear it If the current tuned station does not broadcast traffic announcements press the TRAF button and the radio will seek to a station that does When the radio finds a station that broadcasts traffic announcements the radio will stop and brackets will be displayed around TRAF When a traffic announcement comes on the tuned radio station you will hear it If no station is found NO TRAFFIC will appear on the display lfthe brackets are on the display and TRAF is not you can then press the TRAF button to remove the brackets or use the TUNE knob or the SEEK arrows to go toa station that supports traffic announcements If no station is found NO TRAFFIC will appear on the display Your radio will play the traffic announcements if the volume is low Your radio will interrupt the play of a CD if the last tuned station broadcasts traffic announcements and the brackets are displayed Radio Messages CAL ERR Calibration Error Thi
352. save both batteries And it could save your radio 4 Open the hoods and locate the batteries Find the positive and negative terminals on each vehicle You will not need to access your battery for jump starting Your vehicle has a remote positive jump starting terminal for that purpose The terminal is fare sg a tethered cap at the fron of he relay center SeelEngind erhood f and eae Ovens on page 5 12 for more information on location Flip the cap up to access the remote positive terminal You should always use the remote positive terminal instead of the positive terminal on the battery An electric fan can start up even when the engine is not running and can injure you Keep hands clothing and tools away from any underhood electric fan 5 43 Using a match near a battery can cause battery gas to explode People have been hurt doing this and some have been blinded Use a flashlight if you need more light Fans or other moving engine parts can injure you badly Keep your hands away from moving parts once the engine is running Be sure the battery has enough water You do 5 Check that the jumper cables don t have loose or not need to add water to the ACDelco battery installed in your new vehicle But if a battery has filler caps be sure the right amount of fluid is there If it is low add water to take care of that first If you do not explosive gas could be present Ba
353. se as you drive Set the volume at the desired level Press this button to select MIN MED or MAX Each higher setting will allow for more volume compensation at faster vehicle speeds Then as you drive automatic volume increases the volume as necessary to overcome noise at any speed The volume level should always sound the same to you as you drive If you don t want to use automatic volume select OFF RCL Recall Press this knob to switch the display between the radio station frequency and the time Pressing this knob with the ignition off will display the time For XM 48 contiguous US states if equipped press the RCL knob while in XM mode to retrieve four different categories of information related to the current song or channel Artist Song Title Category or PTY Channel Number Channel Name To change the default on the display press the RCL knob until you see the display you want then hold the knob until the display flashes The selected display will now be the default Finding a Station BAND Press this button to switch between FM1 FM2 AM or XM1 or XM2 48 contiguous US states if equipped The display will show your selection TUNE Turn this knob to select radio stations K SEEK gt Press the right or the left arrow to go to the next or to the previous station and stay there The radio will seek only to stations that are in the selected band and only to those with a strong signal kK SC
354. shape and keep your windshield washer tank filled with washer fluid Replace your windshield wiper inserts when they show signs of streaking or missing areas on the windshield or when strips of rubber start to separate from the inserts Driving too fast through large water puddles or even going through some car washes can cause problems too The water may affect your brakes Try to avoid puddles But if you can not try to slow down before you hit them Wet brakes can cause accidents They will not work as well in a quick stop and may cause pulling to one side You could lose control of the vehicle After driving through a large puddle of water or a car wash apply your brake pedal lightly until your brakes work normally Hydroplaning Hydroplaning is dangerous So much water can build up under your tires that they can actually ride on the water This can happen if the road is wet enough and you are going fast enough When your vehicle is hydroplaning it has little or no contact with the road Hydroplaning does not happen often But it can if your tires do not have much tread or it the pressure in one or more is low It can happen if a lot of water is standing on the road If you can see reflections from trees telephone poles or other vehicles and raindrops dimple the water s surface there could be hydroplaning Hydroplaning usually happens at higher speeds There just is not a hard and fast rule about hydr
355. sieetie evinces 2 10 Outside Convex Mirror ceeeeeeeeeeeeeeeeees 2 31 Leaving Your Vehicle 2 ses 2 10 OnStar System ere ee 2 32 Liftgate Tailgate KSESSELE LEES SESE SELE SE LESS SELE SEES ESS ew Storage Areas ccc ccc cece eee neee eee eeeeeneeeees 2 34 Windows FREESE EF ERE DE FEE FEEL EEE LE FE RE FE FEE FEER 2 12 GIOVE BOX sanne aa 2 34 Power Windows s ssssssiesrisereerrterreereerrrerreerren 2 13 Cupholder S ssssceeeeeereeneeneenrerernernrner 2 34 MUM VISOS as rarere he Rede EA 2 13 Overhead Console oecccccccccccceccccccceeccccceeeccceees 2 34 Theft Deterrent Systems sssseeeeeerree 2 14 Front Door Utility Packs 222 2 36 Content Theft Deterrent ccceeeeeeeeeeeeeeee es 2 14 Console Cooler 0 ccceceeeeeneeeeeaeeaeeneeeeenes 2 36 PASS Key Ul arr ar earn anran cas 2 16 Rear Storage Area W W sdsseeeeeeeeee renere renen ennen 2 37 PASS Key III Operation cccccceeeeeeeeeeee 2 16 Roof Rack System 4 52 eiiie eee 2 38 Starting and Operating Your Vehicle 2 18 Convenience Net 2 ee sees eeeeeeeee eee e ees 2 41 New Vehicle Break In cccccccccccccceccccccccceecceee 2 18 Cargo COVER weiaccccsceccehosnleceencateancubeneanensneswsies 2 42 Ignition Positions ccccccceeeeccceeeeeeceeeeeees 2 18 Cargo Net System 2 2 42 Starting Your Engine ccccceeeeeeeeeeeeeeeeees 2 20 Sliding Rear Convenience Tray 2 2 43 Engine Co
356. splayed when the play button is pressed without a disc in the player Remote Control To use the remote control aim it at the transmitter window below the video screen and press the desired button Direct sunlight or very bright light may affect the ability of the transmitter to receive signals from the remote control Be sure the remote control s batteries are not weak or discharged Objects blocking the line of sight will affect the function of the remote control Notice Storing the remote control in a hot area or in direct sunlight may damage it and the repairs would not be covered by your warranty Store the remote control stored in a cool dry place Remote Control Buttons D Power Press this button to turn the DVD player on or off 2 Title Press this button to go back to the title screen if there is one 3 109 A v lt gt Directional Arrows Press these buttons to move through DVD menus The up arrow will skip to the next chapter or track the down arrow will take you to the beginning of the current chapter or track Press the down arrow twice to take you to the previous chapter or track The right arrow will fast forward and the left arrow will reverse through a chapter or track _ Display Control Button Press this button to adjust color tint brightness contrast and display mode normal full or Zoom The dynamic range compression feature can be used to reduce the loud audio produced
357. ssure cap and cleaning the outside of the radiator and air conditioning condenser is recommended at least once a year d Visually inspect wiper blades for wear or cracking Replace blade inserts that appear worn or damaged or that streak or miss areas of the windshield e Make sure the safety belt reminder light and all your belts buckles latch plates retractors and anchorages are working properly Look for any other loose or damaged safety belt system parts If you see anything that might keep a safety belt system from doing its job have it repaired Have any torn or frayed safety belts replaced Also look for any opened or broken air bag coverings and have them repaired or replaced The air bag system does not need regular maintenance f Lubricate all key lock cylinders hood latch assemblies secondary latches pivots spring anchor and release pawl hood and door hinges rear folding seats and liftgate hinges More frequent lubrication may be required when exposed to a corrosive environment Applying silicone grease on weatherstrips with a clean cloth will make them last longer seal better and not stick or squeak g Check system for interference or binding and for damaged or missing parts Replace parts as needed Replace any components that have high effort or excessive wear Do not lubricate accelerator or cruise control cables h Change automatic transaxle fluid and filter if the vehicle is mainly driven under
358. start your vehicle the engine oil life system has not reset Repeat the procedure If your vehicle has the optional DIC do the following 1 Turn the ignition to ON with the engine off 2 Press the MODE button until the DIC reads OIL LIFE LEFT HOLD SET TO RESET 3 Press and hold the SET button until 100 is displayed You will hear three chimes and the CHANGE ENGINE OIL message will go off 4 Turn the key to OFF If the CHANGE ENGINE OIL message comes back on when you start your vehicle the engine oil life system has not reset Repeat the procedure What to Do with Used Oil Used engine oil contains certain elements that may be unhealthy for your skin and could even cause cancer Do not let used oil stay on your skin for very long Clean your skin and nails with soap and water or a good hand cleaner Wash or properly dispose of clothing or rags containing used engine oil See the manufacturer s warnings about the use and disposal of oil products Used oil can be a threat to the environment If you change your own oil be sure to drain all the oil from the filter before disposal Never dispose of oil by putting it in the trash pouring it on the ground into sewers or into streams or bodies of water Instead recycle it by taking it to a place that collects used oil If you have a problem properly disposing of your used oil ask your dealer a service station or a local recycling center for help Engine Air Cleaner Filter See
359. straint would be very close to the inflating air bag Always secure a rear facing child restraint in a rear seat A rear seat is a safer place to secure a forward facing child restraint If you need to secure a forward facing child restraint in the right front seat you will be using the lap shoulder belt Be sure to follow the instructions that came with the child restraint Secure the child in the child restraint when and as the instructions say 1 Because your vehicle has a right front passenger s air bag always move the seat as far back as it will go before securing a forward facing child restraint See Manual Passenger Seat on page 1 2 2 Put the restraint on the seat 1 59 3 Pick up the latch plate and run the lap and shoulder portions of the vehicle s safety belt through or around the restraint The child restraint instructions will show you how Tilt the latch plate to adjust the belt if needed 4 Buckle the belt Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to 1 60 5 To tighten the belt pull up on the shoulder belt while you push down on the child restraint You may find it helpful to use your knee to push down on the child restraint as you tighten the belt 6 Push and pull the child restraint in different directions to be sure it is secure To remove the child restraint just unbuckle the vehicle s safety belt and
360. strap or top tether It can help restrain the child restraint during a collision For it to work a top strap must be properly anchored to the vehicle Some top strap equipped child restraints are designed for use with or without the top strap being anchored Others require the top strap always to be anchored Be sure to read and follow the instructions for your child restraint If yours requires that the top strap be anchored don t use the restraint unless it is anchored properly If the child restraint does not have a top strap one can be obtained in kit form for many child restraints Ask the child restraint manufacturer whether or not a kit is available In Canada the law requires that forward facing child restraints have a top strap and that the strap be anchored In the United States some child restraints also have a top strap If your child restraint has a top strap it should be anchored 1 49 Anchor the top strap to one of the following anchor points Be sure to use an anchor point located on the same side of the vehicle as the seating position where the child restraint will be placed If you have an adjustable head restraint route the top strap under it If you re using a top strap equipped child restraint in the center rear seat and need to temporarily transport a flat tire for repair move_the child restraint to a rear seat outboard position See Securing a Child Restraint in a Rear Outside Seat Posit
361. t Vehicle Placard A label permanently attached to a vehicle showing the original equipment tire size and recommended inflation pressure See Loading You feed ehicle on page 4 36 5 65 Inflation Tire Pressure The tire and loading information label shows the correct inflation pressures for your tires when they re cold Cold means your vehicle has been sitting for at least hree hours or driven no more than 1 mile 1 6 km See Loading Your Vehicle on page 4 36 for the location of your vehicle s tire and loading information label Notice Don t let anyone tell you that underinflation or overinflation is all right It s not If your tires don t have enough air underinflation you can get the following Too much flexing Too much heat e Tire overloading Bad wear Bad handling Bad fuel economy If your tires have too much air overinflation you can get the following Unusual wear Bad handling Rough ride Needless damage from road hazards 5 66 When to Check Check your tires once a month or more Don t forget your compact spare tire It should be at 60 psi 420 kPa How to Check Use a good quality pocket type gage to check tire pressure You can t tell if your tires are properly inflated simply by looking at them Radial tires may look properly inflated even when they re underinflated Check the tire s inflation pressure when the tires are cold Cold means your veh
362. t s free When you go in to order it take the heaviest coat you will wear so the extender will be long enough for you The extender will be just for you and just for the seat in your vehicle that you choose Don t let someone else use it and use it only for the seat it is made to fit To wear it just attach it to the regular safety belt Child Restraints What is the proper way to wear safety belts mo F If possible an older child should wear a Older Children lap shoulder belt and get the additional restraint a shoulder belt can provide The shoulder belt should not cross the face or neck The lap belt should fit snugly below the hips just touching the top of the thighs It should never be worn over the abdomen which could cause severe or even fatal internal injuries in a crash Accident statistics show that children are safer if they are restrained in the rear seat In a crash children who are not buckled up can strike other people who are buckled up or can be thrown out of the vehicle Older children need to use safety belts properly Older children who have outgrown booster seats should wear the vehicle s safety belts 1 39 Never do this Here two children are wearing the same belt The belt can t properly spread the impact forces In a crash the two children can be crushed together and seriously injured A belt must be used by only one person at a time Q What if a child is wearing a lap shou
363. t or both and to this manual The child restraint instructions are important so if they are not available obtain a replacement copy from the manufacturer 1 47 Where to Put the Restraint Accident statistics show that children are safer if they are restrained in the rear rather than the front seat We therefore recommend that child restraints be secured in a rear seat including an infant riding in a rear facing infant seat a child riding in a forward facing child seat and an older child riding in a booster seat Never put a rear facing child restraint in the front passenger seat Here s why A child in a rear facing child restraint can be seriously injured or killed if the right front passenger s air bag inflates This is because the back of the rear facing child restraint would be very close to the inflating air bag Always secure a rear facing child restraint in a rear seat If you secure a forward facing child restraint in the right front seat always move the front passenger seat as far back as it will go It is better to secure the child restraint in a rear seat 1 48 Wherever you install it be sure to secure the child restraint properly Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure people in the vehicle Be sure to properly secure any child restraint in your vehicle even when no child is in it Top Strap Some child restraints have a top
364. t a crash event or share it with others other than e with the consent of the vehicle owner or if the vehicle is leased with the consent of the lessee e in response to an official request of police or similar government office as part of GM s defense of litigation through the discovery process or e as required by law In addition once GM collects or receives data GM may use the data for GM research needs make it available for research where appropriate confidentiality is to be maintained and need is shown or share summary data which is not tied to a specific vehicle with non GM organizations for research purposes Others such as law enforcement may have access to the special equipment that can read the information if they have access to the vehicle or SDM lf your vehicle is equipped with OnStar please check the OnStar subscription service agreement or manual for information on its operations and data collection Reporting Safety Defects Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death you should immediately inform the National Highway Traffic Safety Administration NHTSA in addition to notifying General Motors If NHTSA receives similar complaints it may open an investigation and if it finds that a safety defect exists in a group of vehicles it may order a recall and remedy campai
365. t on hot engine parts Coolant contains ethylene glycol and it will burn if the engine parts are hot enough Do not spill coolant on a hot engine When the coolant in the coolant recovery tank is at or above the FULL COLD mark start your vehicle If the overheat warning continues there s one more thing you can try You can add the proper coolant mixture directly to the radiator but be sure the cooling system is cool before you do it Steam and scalding liquids from a hot cooling system can blow out and burn you badly They are under pressure and if you turn the radiator pressure cap even a little they can come out at high speed Never turn the cap when the cooling system including the radiator pressure cap is hot Wait for the cooling system and radiator pressure cap to cool if you ever have to turn the pressure cap 5 31 How to Add Coolant to the Radiator Notice Your engine has a specific radiator fill procedure Failure to follow this procedure could cause your engine to overheat and be severely damaged Die ag SS Q gQ 2 B 7 gt se LE AG 1 You can remove the radiator pressure cap when the cooling system including the radiator pressure cap and upper radiator hose is no longer hot Turn the pressure cap slowly counterclockwise until it first stops Do not press down while turning the pressure cap If you hear a hiss wait for that to stop A hiss means there is still s
366. t to get service help right away 5 27 Cooling System When you decide it s safe to lift the hood here s what you ll see An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you Keep hands clothing and tools away from any underhood electric fan If the coolant inside the coolant recovery tank is boiling do not do anything else until it cools down The vehicle should be parked on a level surface A Radiator Pressure Cap B Electric Engine Cooling Fans C Coolant Recovery Tank 5 28 The coolant level should be at or above the FULL Notice Engine damage from running your engine COLD mark If it is not you may have a leak at the without coolant isn t covered by your warranty pressure cap or in the radiator hoses heater hoses See Overheated Engine Protection Operating radiator water pump or somewhere else in the cooling Mode in the Index for information on driving to a system safe place in an emergency Notice Using coolant other than DEX COOL may cause premature engine heater core or radiator corrosion In addition the engine coolant may require changing sooner at 30 000 miles 50 000 km Heater and radiator hoses and other engine or 24 months whichever occurs first Any repairs parts can be very hot Do not touch them If would not be covered by your warranty Always use you do you can be burned DEX COOL silicate free coolant in your
367. t to run as efficiently as designed You may notice this as stalling after start up stalling when you put the vehicle into gear misfiring hesitation on acceleration or stumbling on acceleration These conditions may go away once the engine is warmed up This will be detected by the system and cause the light to turn on If you experience one or more of these conditions change the fuel brand you use It will require at least one full tank of the proper fuel to turn the light off If none of the above steps have made the light turn off your dealer can check the vehicle Your dealer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that may have developed 3 41 Emissions Inspection and Maintenance Programs Some state provincial and local governments have or may begin programs to inspect the emission control equipment on your vehicle Failure to pass this inspection could prevent you from getting a vehicle registration Here are some things you need to know in order to help your vehicle pass an inspection Your vehicle will not pass this inspection if the SERVICE ENGINE SOON or CHECK ENGINE light is on or not working properly Your vehicle will not pass this inspection if the OBD on board diagnostic system determines that critical emission control systems have not been completely diagnosed by the system The vehicle would be considered not ready for inspection This can happen i
368. ta cues E E 2 7 Power Door LOCKS ccceeeeeeeeeeeeeeeeeeeees 2 8 Programmable Automatic Door Locks 2 9 Rear Door Security LOCKS seeeeeeeee trees 2 9 Driver Position Safety Belt c eeeeeeeeeeeee eee es 1 18 Driver BehaviOr cccececeeeeeeeeeeeeeeeeeeeeeeeeees 4 2 Driver Information Center DIC eeeee 3 53 DIC Controls and Displays ceeeeeeeeee 3 55 DIC Vehicle Personalization eeeeeeee 3 57 Driving ANION ES Eee Ear 4 18 GUY ean Sees havent te oe ec dasgcoen E T 4 23 Defensive ccceceeeeceeececeeeeeeeeeeaeeeeeeeaeees 4 3 DRUNK 70 aiitesicicn cite cach SEE SER SEERE SEE ERE RES E EARL are 4 4 ENVIrONMEN ssanie penoa Sikre dose 4 2 FICQWAY ioaeioeenoeea EROL 4 24 Hill and Mountain Roads 4 26 In Rain and on Wet Roads l c 4 20 Winter 55572270 He rand anse Ser E ol 4 28 Driving On Grades cceeeeeeeeeeeeeeeeeeeeeeeen ees 4 48 Driving on Snow or lce ceeeeeeeeeeeee eee eee eee ees 4 29 Driving Through Deep Standing Water 4 22 Driving Through Flowing Water eee 4 22 Driving with a Trailer c eeeeeeeeeeeeeeeeeeeeeee 4 46 Dual Climate Control System eeeeeeee eee 3 27 DVD Cleaning the Video Screen ccecce 3 119 Cleaning Your DVD Player eeeeeees 3 119 Distortion weiiieetaciccietseteence pont dace une s 3
369. that shows the proper operating range your engine could be damaged See Engine Compartment Overviewjon page 5 12 for the location of the engine oil fill cap E7 SAE 5W 30 AR Be sure to add enough oil to put the level somewhere in the proper operating range in the cross hatched area Push the dipstick all the way back in when you are through What Kind of Engine Oil to Use Look for two things GM6094M Your vehicle s engine requires oil meeting GM Standard GM6094M You should look for and use only an oil that meets GM Standard GM6094M SAE 5W 30 As shown in the viscosity chart SAE 5W 30 is best for your vehicle However if it is going to be 0 F 18 C or above and SAE 5W 30 is not available you may use SAE 10W 30 These numbers on an oil container show its viscosity or thickness Do not use other viscosity oils such as SAE 20W 50 RECOMMENDED SAE VISCOSITY GRADE ENGINE OILS LOOK FOR THIS SYMBOL HOT AND GM WEATHER STANDARD GM 6094M TTT SAE 10W 30 ACCEPTABLE IF 5W 30 IS NOT SAESW 30 AVAILABLE RECOMMENDED COLD WEATHER DO NOT USE SAE 10W 40 SAE 20W 50 OR ANY OTHER VISCOSITY GRADE OIL NOT RECOMMENDED Oils meeting these requirements should also have the starburst symbol on the container This symbol indicates that the oil has been certified by the American Petroleum Institute API You should look for this information on the oil container and use only those oils that are
370. the engine running But if you ever have to here are some things to know Idling the engine with the climate control system off could allow dangerous exhaust into our vehicle See the earlier Caution under Engine Exhaustion page 2 29 Also idling in a closed in place can let deadly carbon monoxide CO into your vehicle even if the climate control fan is at the highest setting One place this can happen is a garage Exhaust with CO can come in easily NEVER park in a garage with the engine running Another closed in place can be a blizzard See on page 4 28 2 30 It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK P with the parking brake firmly set Your vehicle can roll Do not leave your vehicle when the engine is running unless you have to If you have left the engine running the vehicle can move suddenly You or others could be injured To be sure your vehicle will not move even when you are on fairly level ground always set your parking brake and move the shift lever to PARK P Follow the proper steps to be sure your vehicle will not move See Shifting Into Park P on page 2 26 If you are pulling a trailer see Towing a Trailen on page 4 42 Mirrors Manual Rearview Mirror To reduce glare from headlamps behind you pull the lever toward you to the night position To return the mirror to the day position push the lever away from you Outsid
371. the sidewall next to the outer side of each outside passenger position 1 35 3 Be sure that the belt is not twisted and it lies flat The guide must be on top of the belt 1 36 4 Buckle position and release the safety belt as described tn Heat Seat Passenger on page 1 28 Make sure that the shoulder belt crosses the shoulder To remove and store the comfort guides squeeze the belt edges together so that you can take them out of the guides Pull the guide upward to expose its storage clip and then slide the guide onto the clip Turn the guide and the clip inward leaving only the loop of elastic cord exposed Second Row Center Position 2 Attach the elastic cord to the comfort guide on the For second row center position do the following center passenger shoulder belt 1 Remove the elastic cord from under the head restraint of the second row driver s side position 3 Be sure that the belt is not twisted and it lies flat The guide must be on top of the belt 4 Buckle position and release the safety belt as on page 1 32 Make sure that the shoulder belt crosses the shoulder To remove and store the elastic cord remove it from the comfort guide The elastic cord will go back under the head restraint 1 38 Safety Belt Extender If the vehicle s safety belt will fasten around you you should use it But if a safety belt isn t long enough to fasten your dealer will order you an extender I
372. the vehicle in a crash if the doors are not locked So wear safety belts properly and lock the doors whenever you drive Young children who get into unlocked vehicles may be unable to get out A child can be overcome by extreme heat and can suffer permanent injuries or even death from heat stroke Always lock your vehicle whenever you leave it Outsiders can easily enter through an From the inside use the manual or power door locks unlocked door when you slow down or To unlock either front door from the inside pull back on stop your vehicle Locking your doors can the manual lever To lock either front door from the help prevent this from happening inside push the manual lever forward Power Door Locks The power door lock switch is located on the driver s and front Press the front of the switch to lock all doors or press the rear of the switch to unlock all doors The rear doors do not have power door lock switches Instead each rear door has a manual lever that works only that door s lock If your vehicle is equipped with the content theft deterrent system the power door lock switch ma cause the system to arm See Content Theft Deterrent on page 2 14 for more information passenger s door armrest Delayed Locking With the delayed locking feature the doors will not lock immediately when locking the doors using the power door lock switch or when LOCK on the remote keyless entry transmitter is pressed whi
373. the way your vehicle handles These could cause you to lose control and crash Also overloading can shorten the life of your vehicle Notice Overloading your vehicle may cause damage Repairs would not be covered by your warranty Do not overload your vehicle If you put things inside your vehicle like suitcases tools packages or anything else they will go as fast as the vehicle goes If you have to stop or turn quickly or if there is a crash they will keep going Things you put inside your vehicle can strike and injure people in a sudden stop or turn or in a crash Put things in the cargo area of your vehicle Try to spread the weight evenly Never stack heavier things like suitcases inside the vehicle so that some of them are above the tops of the seats Do not leave an unsecured child restraint in your vehicle When you carry something inside the vehicle secure it whenever you can Do not leave a seat folded down unless you need to Automatic Level Control On vehicles equipped with automatic level control the rear of the vehicle is automatically kept level as you load or unload your vehicle However you should still not exceed the GVWR or the GAWR See Your Vehicle on page 4 36 You may hear the compressor operating when you load or unload your vehicle and periodically as the system self adjusts This is normal The compressor should operate for brief periods of time If the sound contin
374. ther Cleaning the Top of the Instrument Panel Use only mild soap and water to clean the top surfaces of the instrument panel Sprays containing silicones or waxes may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions Cleaning Interior Plastic Components Use only a mild soap and water solution on a soft cloth or sponge Commercial cleaners may affect the surface finish Cleaning Glass Surfaces Glass should be cleaned often GM Glass Cleaner or a liquid household glass cleaner will remove normal tobacco smoke and dust films on interior glass See Vehicle Care Appearance Materials on page 5 110 Notice If you use abrasive cleaners when cleaning glass surfaces on your vehicle you could scratch the glass and or cause damage to the rear window defogger and the integrated radio antenna When cleaning the glass on your vehicle use only a soft cloth and glass cleaner 5 105 Care of Safety Belts Keep belts clean and dry Do not bleach or dye safety belts If you do it may severely weaken them In a crash they might not be able to provide adequate protection Clean safety belts only with mild soap and lukewarm water Weatherstrips Silicone grease on weatherstrips will make them last longer seal better and not stick or squeak Apply silicone grease with a clean cloth at least every six bare fake very cold damp weather more frequent
375. tion Sunglasses Storage Compartment To open the sunglasses storage compartment in the overhead console press the release button Then pull the compartment down to the full open position Front Door Utility Packs Your vehicle may have front door utility packs If it does the utility packs are located in the front door pockets of your vehicle and are used for extra storage space 2 36 Console Cooler If the cooler storage compartment is not secured properly it can move around in a collision or sudden stop People in the vehicle could be injured Be sure to secure the cooler storage compartment properly Your vehicle may have a fully insulated food beverage console cooler located between the driver s and front passenger s seats To properly secure the console cooler the handle must be latched down Push the handle toward the driver s seat until you hear a click To open the console cooler have the handle fully down toward the passenger s seat then lift the lid up The passenger s seat armrest must be up to be able to open the lid completely The console cooler contains a top tray for storage Remove the top tray to put items in the cooler The cooler also can hold compact discs cassette tapes and it may have a coinholder To remove the console cooler from the vehicle lift the handle from the driver s side to a fully upright position Notice Loading objects that weigh over 400 Ibs 181 kg onto the sliding
376. tion Control System TCS on page 4 10 Then shitt back and forth between REVERSE R and a forward gear spinning the wheels as little as possible Release the accelerator pedal while you shift and press lightly on the accelerator pedal when the transaxle is in gear By slowly spinning your wheels in the forward and reverse directions you will cause a rocking motion that may free your vehicle If that doesn t get you out after a few tries you may need to be towed out If you do need to be towed out see Towing Your Vehicle following 4 33 Towing Towing Your Vehicle Consult your dealer or a professional towing service if ou need to have your disabled vehicle towed See Roadside Assistance Program on page 7 6 If you want to tow your vehicle behind another vehicle for recreational purposes such as behind a motorhome see Recreational Vehicle Towing following Recreational Vehicle Towing Recreational vehicle towing means towing your vehicle behind another vehicle such as behind a motorhome The two most common types of recreational vehicle towing are known as dinghy towing towing your vehicle with all four wheels on the ground and dolly towing towing your vehicle with two wheels on the ground and two wheels up on a device known as a dolly 4 34 With the proper preparation and equipment many vehicles can be towed in these ways See Dinghy Towing and Dolly Towing fol
377. tle when the engine and radiator are hot Add coolant mixture at the recovery tank but be careful not to spill it You can be burned if you spill coolant on hot engine parts Coolant contains ethylene glycol and it will burn if the engine parts are hot enough Don t spill coolant on a hot engine Occasionally check the coolant level in the radiator For information on how to add coolant to the radiator see on page 5 28 Radiator Pressure Cap Notice The radiator cap on your vehicle is a pressure type cap and must be tightly installed to prevent coolant loss and possible engine damage from overheating Be sure the arrows on the cap line up with the overflow tube on the radiator filler neck The radiator pressure cap is located at the front of the engine compartment on the passenger s side of the vehicle See Engine Compartment Overview on page 5 12 for more information on location Engine Overheating You will find an engine coolant temperature on our vehicle s instrument panel See Engine Coola Temperature Gage on page 3 39 Me also have an engine coolant temperature warning me n our instrument panel See Engine Coolant Temperature Warning Message on page 3 44 Overheated Engine Protection Operating Mode This emergency operating mode allows your vehicle to be driven to a safe place in an emergency situation If an overheated engine condition exists an overheat protection mode which alter
378. tlet Adjustment Operation Tips Clear away any ice snow or leaves from the air inlets on the hood that may block the flow of air into your vehicle Use of non GM approved hood deflectors may adversely affect the performance of the system Keep the path under the front seats clear of objects to help circulate the air inside your vehicle more effectively Use the knob located in the center of the outlet to change the direction of the air flow 3 30 Warning Lights Gages and Indicators This part describes the warning lights and gages that may be on your vehicle The pictures will help you locate them Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement Paying attention to your warning lights and gages could also save you or others from injury Warning lights come on when there may be or is a problem with one of your vehicle s functions As you will see in the details on the next few pages some warning lights come on briefly when you start the engine just to let you know they re working If you are familiar with this section you should not be alarmed when this happens Gages can indicate when there may be or is a problem with one of your vehicle s functions Often gages and warning lights work together to let you know when there s a problem with your vehicle When one of the warning lights comes on and stays on when
379. tment See OnStar System on page 2 32 for more information Garage Door Opener Compartment You can store and operate your garage door opener in the third compartment of your overhead console To install your garage door opener follow these instructions 1 Open the compartment by pressing the latch forward 2 Remove the garage door opener button by pressing the tabs and pulling it down 3 Remove the piece of self sticking hook and loop fastener from the top of the garage door opener compartment 4 Peel the protective backing from the hook and loop fastener and press it firmly to the back of your garage door opener 5 Line up the button on the garage door opener with the opening in the storage compartment door Make sure the garage door opener button is facing down and then press the opener firmly into the garage door opener compartment 7 Once the opener is installed remove the three pegs from the garage door opener button Each peg is a different size Put the garage door opener button back in by inserting the tabs into the slot in the garage door opener compartment Press the button on the garage door storage compartment If your garage door opener does not work you will need to change the pegs until it does 2 35 Storage Compartment To open the storage compartment located at the front of the overhead console press the release latch forward Then pull the compartment down to the full open posi
380. to channel 0 should only be if you may have a receiver fault Consult with your dealer hardware failure Chk XMRevr Hardware failure If this message does not clear within a short period of time your receiver may have a fault Consult with your retail location 3 82 Playing a CD With the ignition on insert a CD partway into the slot label side up The player will pull it in READING DISC and the CD symbol will appear on the display and the CD should begin playing If you want to insert a CD with the ignition off first press the EJECT button or push the RCL knob If you insert a CD with the radio off and the ignition on it will start to play If you select an EQ setting for your CD it will be activated each time you play a CD If you turn off the ignition or radio with a CD in the player it will stay in the player When you turn on the ignition or radio the CD will start to play where it stopped if it was the last selected audio source As each new track starts to play the track number will appear on the display The CD player can play the smaller 8cm single CDs with an adapter ring Full size CDs and the smaller CDs are loaded in the same manner If playing a CD R the sound quality may be reduced due to CD R quality the method of recording the quality of the music that has been recorded and the way the CD R has been handled You may experience an increase in skipping difficulty in finding tracks and or diffi
381. to push Anti lock Brake System ABS Your vehicle may have anti lock brakes ABS is an advanced electronic braking system that will help prevent a braking skid ANTI LOCK United States Canada If your vehicle has anti lock brakes this warning light on the instrument panel will come on briefly when you start your vehicle When you start your engine or when you begin to drive away your anti lock brake system will check itself You may hear a momentary motor or clicking noise while this test is going on and you may even notice that your brake pedal moves or pulses a little This is normal Let us say the road is wet and you are driving safely Suddenly an animal jumps out in front of you You slam on the brakes and continue braking Here is what happens with ABS A computer senses that wheels are slowing down If one of the wheels is about to stop rolling the computer will separately work the brakes at each wheel The anti lock system can change the brake pressure faster than any driver could The computer is programmed to make the most of available tire and road conditions This can help you steer around the obstacle while braking hard As you brake your computer keeps receiving updates on wheel speed and controls braking pressure accordingly Remember Anti lock does not change the time you need to get your foot up to the brake pedal or always decrease stopping distance If you get too close to the ve
382. ton while a DVD is playing to pause it Press it again to continue playing the DVD or CD gt Next Chapter Track Press this button to go to the beginning of the next chapter or track This button may not work when the DVD is playing the copyright information or the previews 3 111 Setup Menu To access the setup Menu ensure that a DVD is in the player and the video is stopped Press the main menu button Once the menu is activated use the directional arrows and the enter button to navigate the screen The setup menu allows the user to select default preferences for Menu Language Subtitle Language Audio Language TV Aspect TV Mode and Dynamic Range Compression Not all DVDs support all the feature defaults in the setup menus In the event a particular feature is not supported defaults will be provided by the DVD media Exit the setup menu by pressing the return button on the remote control or the DVD player If you make changes to the system setup defaults the disc will resume play from its beginning and not where it previously left off 3 112 Battery Replacement To change the remote control batteries do the following 1 Unclip the battery door located on the back of the remote control 2 Replace the two AA batteries in the compartment Make sure that they are installed correctly using the diagram on the inside of the battery compartment 3 Close the battery door If the remote control is to be
383. traighten out Always be ready for a second skid if it occurs Of course traction is reduced when water snow ice gravel or other material is on the road For safety you will want to slow down and adjust your driving to these conditions It is important to slow down on slippery surfaces because stopping distance will be longer and vehicle control more limited While driving on a surface with reduced traction try your best to avoid sudden steering acceleration or braking including engine braking by shifting to a lower gear Any sudden changes could cause the tires to slide You may not realize the surface is slippery until your vehicle is skidding Learn to recognize warning clues such as enough water ice or packed snow on the road to make a mirrored surface and slow down when you have any doubt If you have the anti lock braking system remember It helps avoid only the braking skid If you do not have anti lock then in a braking skid where the wheels are no longer rolling release enough pressure on the brakes to get the wheels rolling again This restores steering control Push the brake pedal down steadily when you have to stop suddenly As long as the wheels are rolling you will have steering control Driving at Night Night driving is more dangerous than day driving One reason is that some drivers are likely to be impaired by alcohol or drugs with night vision problems or by fatigue 4 18
384. ttery fluid contains acid that can burn you Do not get it on you If you accidentally get it in your eyes or on your skin flush the place with water and get medical help immediately 5 44 missing insulation If they do you could get a shock The vehicles could be damaged too Before you connect the cables here are some basic things you should know Positive will go to positive or to a remote positive terminal if the vehicle has one Negative will go to a heavy unpainted metal engine part or to a remote negative terminal if the vehicle has one Don t connect positive to negative or you ll get a short that would damage the battery and maybe other parts too And don t connect the negative cable to the negative terminal on the dead battery because this can cause sparks Connect the red positive cable to the positive terminal of the dead battery Use a remote positive terminal if the vehicle has one Don t let the other end touch metal Connect it to the positive terminal of the good battery Use a remote positive terminal if the vehicle has one 8 Now connect the black negative cable to the negative terminal of the good battery Use a remote negative terminal if the vehicle has one Don t let the other end touch anything until the next step The other end of the negative cable doesn t go to the dead battery It goe
385. u In a crash you could go into it receiving neck or other injuries The lap belt can t do its job either In a crash the belt could go up over your abdomen The belt forces would be there not at your pelvic bones This could cause serious internal injuries For proper protection when the vehicle is in motion have the seatback upright Then sit well back in the seat and wear your safety belt properly Head Restraints Adjust your head restraint so that the top of the restraint is closest to the top of your head This position reduces the chance of a neck injury in a crash The front seat head restraints are adjustable Slide the head restraint up or down to adjust it The rear seat head restraints in your vehicle may be adjustable They work the same as the front seat head restraints Rear Seats Rear Seat Operation The rear seats in your vehicle have seat operating features to adjust fold remove and reinstall the seats By using the seat operating procedures in the correct order you can easily remove the seats from your vehicle When you put the seats back in the vehicle be sure to follow the label on the back of the seat for proper location Split Bench Seats The seatbacks can be folded forward or reclined individually and the sections can be flipped forward or removed individually 1 6 Folding or Reclining the Seatbacks If the seatback isn t locked it could move forward in a sudden stop or
386. ues for an extended period of time your vehicle needs service Using heavier suspension components to get added durability might not change your weight ratings Ask your dealer to help you load your vehicle the right away 4 41 Towing a Trailer If you don t use the correct equipment and drive properly you can lose control when you pull a trailer For example if the trailer is too heavy the brakes may not work well or even at all You and your passengers could be seriously injured Pull a trailer only if you have followed all the steps in this section Ask your dealer for advice and information about towing a trailer with your vehicle Notice Pulling a trailer improperly can damage your vehicle and result in costly repairs not covered by your warranty To pull a trailer correctly follow the advice in this part and see your dealer for important information about towing a trailer with your vehicle Additional rear axle maintenance is required for a vehicle used to tow a trailer See Scheduled Maintenance Services in the Index 4 42 Your vehicle can tow a trailer To identify what the vehicle trailering capacity is for your vehicle you should read the information in Weight of the Trailer that appears later in this section But trailering is different than just driving your vehicle by itself Trailering means changes in handling acceleration braking durability and fuel economy Successful safe trailerin
387. uice milk soft drinks vomit urine and blood can be removed as follows 1 Carefully scrape off excess stain then sponge the soiled area with cool water 2 If a stain remains follow the cleaning instructions described earlier 3 If an odor lingers after cleaning vomit or urine treat the area with a water and baking soda solution 1 teaspoon 5 ml of baking soda to 1 cup 250 ml of lukewarm water 4 Let dry Stains caused by candy ice cream mayonnaise chili sauce and unknown stains can be removed as follows 1 Carefully scrape off excess stain 2 Clean with cool water and allow to dry completely 3 If a stain remains follow the cleaner instructions described earlier Cleaning Vinyl Use warm water and a clean cloth e Rub with a clean damp cloth to remove dirt You may have to do this more than once Things like tar asphalt and shoe polish will stain if you do not get them off quickly Use a clean cloth and vinyl cleaner See your dealer for this product Cleaning Leather Use a soft cloth with lukewarm water and a mild soap or saddle soap and wipe dry with a soft cloth Then let the leather dry naturally Do not use heat to dry For stubborn stains use a leather cleaner Never use oils varnishes solvent based or abrasive cleaners furniture polish or shoe polish on leather Soiled or stained leather should be cleaned immediately If dirt is allowed to work into the finish it can harm the lea
388. uldn t be covered by your warranty 5 42 Trying to start your vehicle by pushing or pulling it won t work and it could damage your vehicle 1 Check the other vehicle It must have a 12 volt battery with a negative ground system Notice If the other vehicle s system is not a 12 volt system with a negative ground both vehicles can be damaged Only use vehicles with 12 volt systems with negative grounds to jump start your vehicle 2 Get the vehicles close enough so the jumper cables can reach but be sure the vehicles aren t touching each other If they are it could cause a ground connection you don t want You wouldn t be able to start your vehicle and the bad grounding could damage the electrical systems To avoid the possibility of the vehicles rolling set the parking brake firmly on both vehicles involved in the jump starting procedure Put an automatic transaxle in PARK P or a manual transaxle in NEUTRAL before setting the parking brake Notice If you leave your radio or other accessories on during the jump starting procedure they could be damaged The repairs would not be covered by your warranty Always turn off your radio and other accessories when jump starting your vehicle 3 Turn off the ignition on both vehicles Unplug unnecessary accessories plugged into the cigarette lighter or in the accessory power outlet s Turn off the radios and all lamps that aren t needed This will avoid sparks and help
389. ulty with remote transmitters such as a garage door opener try pointing the device through the very top of the windshield XM Satellite Radio Antenna System 48 Contiguous US States Your XM Satellite Radio antenna is located on the roof of your vehicle Keep this antenna clear of snow and ice build up for clear radio reception The performance of your XM system may be affected if your sunroof is open Loading items onto the roof of your vehicle can interfere with the performance of your XM system Make sure that the XM satellite antenna is not obstructed 3 119 4 NOTES 3 120 Section 4 Your Driving the Road and Your Vehicle 4 2 Driver Behavior sss 5 bre tio osoin isa 4 2 Driving Environment sssri densis tirinesni aseina 4 2 Vehicle Desig s sicssatariirsnnias nrnna 4 3 Defensive Driving ccseeeeeeeeeeeeeeeneeeeeeeees 4 3 Drunken DIVING re anne renen O 4 4 Control of a Vehicle W W sssseeererererenennee 4 7 Braking eaaa Sines rch see lee enebarn 4 7 Traction Control System TCS o ae 4 10 All Wheel Drive AWD System n 4 12 cS 1214100 ee 4 12 Off Road ReCOVErY ccceeeeeeeeeeeeeee eee een tenes 4 14 PASSING armin ene E ber emetic 4 15 Loss Of GOntroll anede nenne 4 16 Driving at Night cite se weeiece shee einai 4 18 Driving in Rain and on Wet Roads 4 20 Driving Your Vehicle City DIVIN Oheisena aiao i 4 23 Freeway Driving 26255
390. until it has been repaired or replaced 5 90 Removing the Flat Tire and Installing the Spare Tire 1 If there is a wheel cover loosen the plastic nut caps with the wheel wrench They won t come off Then using the flat end of the wheel wrench pry along the edge of the cover until it comes off Be careful the edges may be sharp Don t try to remove the cover with your bare hands If your vehicle has aluminum wheels remove the wheel nut caps using the wheel wrench Loosen the wheel nuts but do not remove them using the folding wrench Turn the handle about 180 degrees then flip the handle back to the starting position This avoids taking the wrench off the lug nut for each turn For wheels with a wheel lock key use the wheel lock key between the lock nut and folding wrench The key is supplied in the front passenger door Notice If your vehicle has wheel locks and you use an impact wrench to remove the wheel nuts you could damage the lock nut or wheel lock key Do not use an impact wrench to remove the wheel nuts if your vehicle has wheel locks 5 91 3 0 inches 7 5 cm 5 92 3 Near each wheel there is a notch in the vehicle s body Position the jack and raise the jack head until it fits firmly into the notch in the vehicle s frame nearest the flat tire Notice If you use a jack to raise the vehicle without positioning it correctly you could damage your vehicle
391. ur radio will interrupt the play of a CD if the last tuned station broadcasts traffic announcements and the brackets are displayed This function does not apply to XM Satellite Radio Service Radio Messages CALIBRATE Your audio system has been calibrated for your vehicle from the factory If CALIBRATE appears on the display it means that your radio has not been configured properly for your vehicle and must be returned to the dealership for service XM Radio Messages Radio Display ar 7 XL Explicit Language XL on the radio display These channels or any others can be blocked at a Channels after the channel name customer s request by calling 1 800 852 XMXM 9696 indicates content with explicit language Updating Updating The encryption code in your receiver is being updated and encryption code no action is required This process should take no longer than 30 seconds No Signal Loss of signal Your system is functioning correctly but you are in a location that is blocking the XM signal When you move into an open area the signal should return Loading XM Acquiring channel audio Your radio system is acquiring and processing audio and after 4 second delay text data No action is needed This message should disappear shortly CH Off Air Channel not in service This channel is not currently in service Tune to another channel CH Unavail Channel no longer This previously assigned channel is no longer assigned
392. use it affects the total or gross weight of your vehicle The Gross Vehicle Weight GVW includes the curb weight of the vehicle any cargo you may carry in it and the people who will be riding in the vehicle If you have a lot of options passengers or cargo in the vehicle it will reduce the tongue weight your vehicle can carry which will also reduce the trailer weight your vehicle can tow And if you will tow a trailer you must add the tongue load to the GVW because your vehicle will be carrying that weight too See Loading Your Vehicle on page 4 36 for more information about your vehicle s maximum load capacity 4 44 If you are using a weight carrying or a weight distributing hitch the trailer tongue weight A should be 10 percent to 15 percent of the total loaded trailer weight B Do not exceed the maximum allowable tongue weight for your vehicle After you have loaded your trailer weigh the trailer and then the tongue separately to see if the weights are proper If they are not you may be able to get them right simply by moving some items around in the trailer Total Weight on Your Vehicle s Tires Be sure your vehicle s tires are inflated to the upper limit for cold tires You will find these numbers on the Certification Tire Lab el at the rear edge of the driver s door or see on page 4 36 Then be sure you do not go over the GVW limit for your vehicle including the weight of the trailer tongue Hitches
393. ut removed rom te venicIe by folowirigtne Repeat these steps for the other section of the split next steps bench seat Replacing the Split Bench Seats A safety belt that is improperly routed not properly attached or twisted won t provide the If the seatback isn t locked it could move forward in a sudden stop or crash That could cause injury to the person sitting there Always press rearward on the seatback to be sure it is locked protection needed in a crash The person wearing the belt could be seriously injured After installing the seat always check to be sure that the safety belts are properly routed and attached and are not twisted Make sure the seatback is in the folded forward position and the safety belts are on the correct section of the seat Don t put the sections of the bench seat in so they face rearward because they won t latch that way A seat that isn t locked into place properly can i i o move around in a collision or sudden stop The split bench seat sections have seat position labels located on the back of each section showing where People in the vehicle could be injured Be sure the section must go to lock the seat into place properly when installing it The seat must be placed in the proper location for the legs to attach correctly 2 Make sure the bench seat is angled so that the front hooks clear the floor pins lf the front legs are not attached correctly the rear legs wi
394. utes The light in the switch will blink After about one minute you can use the system again Press the inflator switch and the indicator light will come on Notice If you run the accessory inflator longer than 30 minutes at a time you could damage the inflator The repairs would not be covered by your warranty Run the inflator for short periods of time only After running the accessory inflator for 30 minutes wait at least 10 minutes before restarting the accessory inflator To turn off the inflator do the following 1 Press the switch and detach the hose first from the inflated object then from the outlet 2 Put the protective cap back on 3 Place the inflator kit tools in the pouch and store in the glove box To put the cover back on line up the tabs at the back of the cover and put it in place Push down the tab to secure the cover If a Tire Goes Flat It s unusual for a tire to blowout while you re driving especially if you maintain your tires properly If air goes out of a tire it s much more likely to leak out slowly But if you should ever have a blowout here are a few tips about what to expect and what to do If a front tire fails the flat tire will create a drag that pulls the vehicle toward that side Take your foot off the accelerator pedal and grip the steering wheel firmly Steer to maintain lane position and then gently brake to a stop well out of the traffic lane 5 77 A
395. vailable in all 50 states and the District of Columbia Eligibility is limited by vehicle age mileage and other factors General Motors reserves the right to change eligibility limitations and or discontinue its participation in this program Online Owner Center The Owner Center is a resource for your GM ownership needs You can find your specific vehicle information all in one place The Owner Center allows you to Get e mail service reminders Access information about your specific vehicle including tips and videos and an electronic version of this owner s manual United States only Keep track of your vehicle s service history and maintenance schedule Find GM dealers for service nationwide e Receive special promotions and privileges only available to members United States only Refer to the web for updated information To register your vehicle visit www MyGMLink com United States or My GM Canada within www gmcanada com Canada Customer Assistance for Text Telephone TTY Users To assist customers who are deaf hard of hearing or speech impaired and who use Text Telephones TTYs Pontiac has TTY equipment available at its Customer Assistance Center Any TTY user can communicate with Pontiac by dialing 1 800 833 PONT 7668 TTY users in Canada can dial 1 800 263 3830 Customer Assistance Offices Pontiac encourages customers to call the toll free number for assistance If a U S customer
396. ve the tray from the vehicle The rear of the tray has rollers for you to move it on the ground in an upright position without having to carry it Removing the Floor Track Assembly 1 Feed the tethered ring through the rear lower sidewall loop on each side of the vehicle After the tray is removed the floor track assembly also 5 Unlock ihe slide locks from tho two rear toor needs to be removed Items should not be put onto hina th d d the floor track assembly retainers by pushing the button down and pressing them inward 3 Disengage the front forks from the retainers by lifting and pulling the assembly toward you 2 45 Replacing the Floor Track Assembly Before beginning this procedure make sure that nothing is in the rear of the vehicle 1 Slide the floor track assembly in while aligning the front forks located on the bottom front of the track assembly so that the forks slide under the two front floor retainers 2 Insert the slide locks under the two rear floor retainers by pushing the button down and pressing them outward 2 46 You may have to apply downward pressure to the floor track assembly to engage the slide locks under the floor retainers Double check to ensure that the slide locks are engaged under the retainers and locked into place Feed the tethered ring upward through the lower sidewall loop on each side of the vehicle Make sure that the tethered ring is placed on the outer edg
397. vehicle Do not run the engine if there is a leak If you run the engine it could lose all coolant That could cause an engine fire and you could be burned Get any leak fixed before you drive the vehicle If there seems to be no leak with the engine on check to see if the electric engine cooling fans are running If the engine is overheating both fans should be running If they are not your vehicle needs service 5 29 How to Add Coolant to the Coolant Recovery Tank If you have not found a problem yet but the coolant level is not at or above the FULL COLD mark add a 50 50 mixture of clean drinkable water and DEX COOL engine coolant at the coolant recovery tank See Engine Coolant on page 5 22 for more information Adding only plain water to your cooling system can be dangerous Plain water or some other liquid such as alcohol can boil before the proper coolant mixture will Your vehicle s coolant warning system is set for the proper coolant mixture With plain water or the wrong mixture your engine could get too hot but you would not get the overheat warning Your engine could catch fire and you or others could be burned Use a 50 50 mixture of clean drinkable water and DEX COOL coolant 5 30 Notice In cold weather water can freeze and crack the engine radiator heater core and other parts Use the recommended coolant and the proper coolant mixture You can be burned if you spill coolan
398. ver exceed XXX kg or XXX Ibs A ORIGINAL COLD TIRE TIRE SIZE INFLATION PRESSURE SEE OWNER S cae RR ee te A Vehicle Capacity Weight The Tire and Loading Information label is attached to the center pillar near the driver s door latch Vehicles without a center pillar will have the Tire and Loading Information label attached to the driver s door edge This label lists the number of people that can be in your vehicle and the total weight it can carry This weight is called the vehicle capacity weight The Tire and Loading Information label also tells you the size and recommended inflation pressure for the original equipment tires on your vehicle For more information on tires and inflation see on page 5 58 and Inflation Tire Pressure on page 5 66 lf your vehicle does not have the Tire and Loading Information label the Certification Tire label shows the tire size and recommended inflation pressures needed to obtain the Gross Vehicle Weight Rating GVWR and the Gross Axle Weight Rating GAWR for the front and rear axles See Certification Tire Label later in this section Steps for Determining Correct Load Limit 1 Locate the statement The combined weight of occupants and cargo should never exceed XXX pounds on your vehicle placard 2 Determine the combined weight of the driver and passengers that will be riding in your vehicle 3 Subtract the combined weight of the driver and passengers fr
399. vice The vehicle is moving faster than 70 mph 113 km h The system is not yet calibrated The tire treadwear is uneven The compact spare tire is installed Tire chains are being used The vehicle is being driven on a rough or frozen road If the anti lock brake system warning light comes on the check tire pressure system may not be working properly See your dealer for service Also see Anti Lock Brake System Warning Light on page 3 37 The check tire pressure system detects differences in tire rotation speeds that are caused by changes in tire pressure The system can alert you about a low tire but it does not replace normal tire maintenance See on page 5 58 When the TIRE PRESSURE LOW CHECK TIRES message appears on the Driver Information Center and the LOW TIRE PRESSURE message comes on the message center you should stop as soon as you can and check all your tires for damage If a tire is flat see lita Tire Goes Flal on page 5 77 Also check the tire e es as soon as you can See inflation Tire Pjesshre on page 5 66 Any time you adjust a tire s pressure or have one or more tires repaired or replaced you ll need to reset or calibrate the check tire pressure system You will also need to reset the system whenever you rotate the tires buy new tires and install or remove the compact spare Do not reset the check tire pressure system without first correcting the cause of the problem an
400. vices can be heard through the following possible sources e Wireless Headphones Vehicle s Speakers e Wired Headphones Not included Only one audio source can be heard through the vehicles speakers at a time You can listen to the entertainment system or an auxiliary device through all of the vehicles speakers when the following occurs A DVD or auxiliary device is playing The front audio system is on and the CD AUX button is pressed to enable the entertainment system The front audio system will display RSE when the entertainment system is on and RSE OFF when it is off To turn the vehicles speakers on and off press the CD AUX button on the front audio system The audio from the entertainment system can be heard through both the wireless headphones and the vehicles speakers at the same time The volume on the audio system may vary when switching between a radio station CD DVD or auxiliary device If there is a decreased audio signal during CD or DVD play you may hear a low hissing noise through the speakers and or headphones If the hissing sound in the wireless headphones seems excessive make sure that the headphone batteries are fully charged Some amount of hissing is normal Video Screen The video screen is located in the overhead console To use the video screen do the following 1 Push forward on the release button and the screen will fold down 2 Push the screen away from you and a
401. warning light should go off See Traction Control System TCS on page 4 10 for more information 3 38 Engine Coolant Temperature Gage Canada United States This gage shows the engine coolant temperature If the gage pointer moves into the red area your engine is too hot lt means that your engine coolant has overheated If you have been operating your vehicle under normal driving conditions you should pull off the road stop your vehicle and turn off the engine as soon as possible See Engine Overheating on page 5 25 Malfunction Indicator Lamp Service Engine Soon Light in the United States or Check Engine Light in Canada SERVICE ENGINE SOON United States Canada Your vehicle is equipped with a computer which monitors operation of the fuel ignition and emission control systems This system is called OBD II On Board Diagnostics Second Generation and is intended to assure that emissions are at acceptable levels for the life of the vehicle helping to produce a cleaner environment The SERVICE ENGINE SOON or CHECK ENGINE light comes on to indicate that there is a problem and service is required Malfunctions often will be indicated by the system before any problem is apparent This may prevent more serious damage to your vehicle This system is also designed to assist your service technician in correctly diagnosing any malfunction Notice If you keep driving your vehicle with this light on after a
402. wer Seats and Mirrors and Body computer 47 Main Battery Fuse for Climate Control Blower and Ignition 3 Relay Main Battery Fuse for Ignition Switch Radio Heads Up Display Remote Keyless Entry RKE Instrument Cluster Air Conditioning and Body Computer Diode for Air Conditioning 70 Compressor Clutch C Reay Usse eo Ignition 7 Rey 5 117 Capacities and Specifications The following approximate capacities are given in English and metric conversions Refer to Recommended Fluids and Lubricant nd Lubricants on page 6 12 for more information Application Air Conditioning Refrigerant R134a Automatic Transaxle Pan Removal and Replacement Complete Overhaul 7 4 quarts 10 0 quarts AWD Automatic Transaxle Pan Removal and Replacement 8 7 quarts 10 8 quarts Complete Overhaul 5 118 Engine Specifications Engine VIN Code Spark Plug Gap Feer mt En 5 119 4 NOTES 5 120 Section 6 Maintenance Schedule Maintenance Schedule 0 seeeeeeeneees 6 2 Owner Checks and Services 6 8 IMMOGUCHON senses tes Als RR net bende dan veh decane 6 2 At Each Fuel Pill SL sa dare ee ediehestebbens 6 8 Maintenance Requirements eceeeeeeeee ee 6 2 At Least Once a Month n 6 9 Your Vehicle and the Environment 6 2 At Least Once a Year cceeeeeeeeeeeeeeeen eee eeee 6 9 Using Your Maintenance Schedule 6 3 Recomme
403. will remain unlocked until locked again Disarming with Your Key Your alarm system will disarm when you use your key to unlock the driver s door The security light will stop flashing to let you know the system is no longer armed Disarming with the Remote Keyless Entry Transmitter Your alarm system will disarm when you press UNLOCK on your remote keyless entry transmitter to unlock the doors The security light will stop flashing to let you know the system is no longer armed PASS Key III Your PASS Key III system operates on a radio frequency subject to Federal Communications Commission FCC Rules and with Industry Canada This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This device complies with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference received including interference that may cause undesired operation of the device Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment PASS Key III uses a radio frequency transponder in the key that matches a decoder in your vehicle PASS Key
404. wire wheel covers See your General Mo Q Da men TO nese Removes dust products See Recommended Fluids and Lubricants fingerprints and surface 7 contaminants Spray on onpage Gte wipe off Cleans vinyl tops phosphate free Vinyl Cleaner upholstery and Quickly and easily convertible tops Spot Lifter removes spots and stains Finish Enhancer 5 110 Vehicle Identification Vehicle Identification Number VIN SAMPLE4UX1M072675 This is the legal identifier for your vehicle It appears on a plate in the front corner of the instrument panel on the driver s side You can see it if you look through the windshield from outside your vehicle The VIN also appears on the Vehicle Certification and Service Parts labels and the certificates of title and registration Engine Identification The 8th character in your VIN is the engine code This code will help you identify your engine specifications and replacement parts Service Parts Identification Label You will find this label on the inside of the access panel located on the driver s side of the rear of the vehicle It is very helpful if you ever need to order parts On this label you will find the following VIN Model designation Paint information A list of all production options and special equipment Be sure that this label is not removed from the vehicle 5 111 Electrical System Add On Electrical Equipment Notice Don t add anything electrical t
405. wishes to write to Pontiac the letter should be addressed to Pontiac s Customer Assistance Center United States Customer Assistance Pontiac GMC Customer Assistance Center P O Box 33172 Detroit MI 48232 5172 1 800 762 2737 or 1 800 833 7668 For Text Telephone devices TTYs Roadside Assistance 1 800 ROADSIDE 762 3743 Fax Number 313 381 0022 From Puerto Rico 1 800 496 9992 English 1 800 496 9993 Spanish Fax Number 313 381 0022 From U S Virgin Islands 1 800 496 9994 Fax Number 313 381 0022 Canada Customer Assistance General Motors of Canada Limited Customer Communication Centre 163 005 1908 Colonel Sam Drive Oshawa Ontario L1H 8P7 1 800 263 3777 English 1 800 263 7854 French 1 800 263 3830 For Text Telephone devices TTYs Roadside Assistance 1 800 268 6800 Overseas Customer Assistance Please contact the local General Motors Business Unit Mexico Central America and Caribbean Islands Countries Except Puerto Rico and U S Virgin Islands Customer Assistance General Motors de Mexico S de R L de C V Customer Assistance Center Paseo de la Reforma 2740 Col Lomas de Bezares C P 11910 Mexico D F 01 800 508 0000 Long Distance 011 52 53 29 0 800 GM Mobility Program for Persons with Disabilities This program available to qualified applicants can reimburse you up to 1 000 toward eligible aftermarket driver or passenger adaptive equipment you m
406. wrench to the hoist shaft Use the extension tube if you have the sliding rear convenience tray Turn the folding wrench clockwise to lift the spare tire For all wheel drive vehicles when the tire reaches the stabilizer bar move the tire over the bar then continue to turn the folding wrench clockwise to lift the spare tire When the tire is almost in the stored position turn the tire so the valve stem is towards the rear of the vehicle 5 98 This will help when you check and maintain tire pressure in the spare Raise the tire fully against the underside of the vehicle Continue turning the folding wrench until you feel more than two clicks This indicates that the compact spare tire is secure and the cable is tight The spare tire hoist cannot be overtightened A Push and Pull B Turn Tire 8 Make sure the tire is stored securely Push pull and then try to turn the tire If the tire moves use the folding wrench to tighten the cable Put back all tools as they were stored in the jack storage compartment and put the compartment cover back on To put the cover back on slip the tabs on the bottom of the cover into the bottom of the cover opening Push the cover in place and push down the tab on the top of the cover so that it rests in the groove This secures the cover in place When you replace the compact spare with a full size tire reinstall the bolt on wheel covers or the center cap wh
407. y III Security cccccccccceeeceeeeeeeees 3 48 Program Mod als res enke eiman 3 51 Message cont Rear Hatch Ajar Warning ccecce 3 48 Remote Keyless Entry Transmitter Battery Low Warning 22260 bike danne 3 52 Service Traction System Warning 3 43 Service Vehicle SOON n 3 51 Traction Active cccccceeeee cece ee ee eee ure ark ere an ale 3 44 Mexico Central America and Caribbean Islands Countries Except Puerto Rico and U S Virgin Islands Customer Assistance 0 0606 7 5 Mirrors Manual Rearview Mirror ccceeeeeeeeeeees 2 31 Outside Convex Mirror ccccceeeeeeeeeeeenes 2 31 Outside Power Mirrors cccceeeeeeeeeeenes 2 31 MYGMLINK COM 3 rd raunen aa aana 7 4 New Vehicle Break In ccccecccceeeeeeeeeeeenes 2 18 Normal Maintenance Replacement Parts 6 13 OdGOMCIE sccssisccccicsctcccstcaccditnadwisdancadsccstenagedand 3 33 Off Road Recovery usa eeta 4 14 Oil EAGINE 22 re l raii ai kaa a i babes ede 5 13 Pressure Message eceeeeeeeeeeeeeeeeeeees 3 45 Older Children Restraints cccceeeeeeee es 1 39 Online Owner Center cccccceeeeeeeeeeeeeeeaes 7 4 OnStar Personal Calling ccccccceeeeeeeeeeees 2 33 OnStar Services eni aen nr eee Hanne aber 2 32 OnStar System ccccccccecccceeeeeeeeeeeeeeeeeeeeaaes 2 32 OnStar Virtual Advisor sssssseeeeeeeeee
408. y see CD Messages later in this section DD 1 Forward Press and hold this pushbutton to advance quickly within a track You will hear sound at a reduced volume Release the pushbutton to play the passage The display will show the elapsed time of the track RDM 3 Random Press this pushbutton to hear the tracks in random rather than sequential order RDM and the track number will appear on the display Press RDM again to turn off random play 444 Reverse Press and hold this pushbutton to reverse quickly within a track You will hear sound at a reduced volume Release the pushbutton to play the passage The display will show the elapsed time of the track EQ Equalizer Press EQ to select the desired customized equalization setting while playing a CD The equalization will be automatically set whenever you play a CD See EQ listed previously for more information 3 73 A SEEK V Press the down arrow while playing a CD to go to the start of the current track if more than eight seconds have played Press the up arrow to go to the next track If you hold either arrow or press it more than once the player will continue moving backward or forward through the CD A SCAN V Press and hold either arrow for more than two seconds until SCAN and the track number appear on the display and you hear a beep The CD will go to the next track play for a few seconds then go on to the next track Press either arrow aga
409. y on if your parking brake doesn t release fully If it stays on after your parking brake is fully released it means you have a brake problem Your vehicle s hydraulic brake system is divided into two parts If one part isn t working the other part can still work and stop you For good braking though you need both parts working well If the warning light comes on there could be a brake problem Have your brake system inspected right away O P Canada BRAKE United States This light should come on briefly when you turn the ignition key to ON If it doesn t come on then have it fixed so it will be ready to warn you if there s a problem If the light comes on while you are driving pull off the road and stop carefully You may notice that the pedal is harder to push Or the pedal may go closer to the floor It may take longer to stop If the light is still on have the vehicle towed for service See on page 3 37 and on page 4 34 Your brake system may not be working properly if the brake system warning light is on Driving with the brake system warning light on can lead to an accident If the light is still on after you have pulled off the road and stopped carefully have the vehicle towed for service Anti Lock Brake System Warning Light ANTI LOCK Canada United States Your vehicle may have an anti lock brake system warning light If it does the light should come on for a few seconds when
410. y to put a wheel cover on the compact spare you could damage the cover or the spare Storing a Flat or Spare Tire and Tools The underbody mounted spare tire needs to be stored with the valve stem pointing down If the spare tire is stored with the valve stem pointing upwards its secondary latch won t work properly and the spare tire could loosen Storing a jack a tire or other equipment in the passenger compartment of the vehicle could cause injury In a sudden stop or collision loose equipment could strike someone Store all these in the proper place and suddenly fall from your vehicle If this happened when your vehicle was being driven the tire might contact a person or another vehicle causing injury and of course damage to itself as well Be sure the underbody mounted spare tire is stored with its valve stem pointing down 5 97 Storing the Spare Tire and Tools 1 Lay the compact spare tire on the ground at the rear of the vehicle Position the compact spare tire so the valve stem is pointed down facing the rear of the vehicle Lower the cable to the ground See Removing the Spare Tire without the Sliding Rear Convenience Tray or Removing the Spare Tire with the Sliding Rear Convenience Tray earlier in this section Tilt the retainer downward and slip it through the center hole of the spare tire Make sure the retainer is fully seated across the underside of the wheel Attach the folding
411. yer faceplate or the remote control As long as the disc has not been ejected and the stop button has not been pressed twice on the remote control or the DVD player faceplate the movie should resume play from where it was last stopped If the disc has been ejected or if the stop button has been pressed twice on the remote control or the DVD player faceplate the disc will resume play at the beginning of the disc 3 108 Ejecting a Disc Press the eject button on the DVD player faceplate to eject the disc There is not an eject button on the remote control If a disc is ejected from the player but not removed the DVD player will reload the disc after a short period of time The disc will be stored in the DVD player The DVD player will not resume play of the disc automatically DVD Messages The following errors may be displayed on the video screen Disc Format Error This message will be displayed if a disc is inserted upside down if the disc is not readable or if the disc format is not compatible with the DVD player Disc Play Error This message will be displayed if the mechanism can not play the disc Scratched or damaged discs will cause this error Region Code Error This message will be displayed if the region code of the DVD is not compatible with the region code of the DVD player Load Eject Error This message will be displayed if the disc is not properly loaded or ejected No Disc This message will be di
412. yless entry transmitter when the interior lamp control is in the DOOR position and the ignition is in OFF After 25 seconds the interior lamps will fade out The lamps will turn off before 25 seconds if one of the following occurs All doors are locked using the key e LOCK is pressed on the remote keyless entry transmitter The front of the power door lock switch is pressed The ignition is turned to ON When any door is opened entry lighting is cancelled The interior lamps will stay on while any door or the liftgate is open and fade out when all the doors are closed Delayed Lighting The delayed lighting feature will continue to illuminate the interior for 25 seconds after all doors have been closed The lamps will continue to illuminate when the following conditions are met A door is opened then closed The interior lamp control is in the DOOR position The ignition is in OFF After 25 seconds the interior lamps will fade out The lamps will fade out before the 25 seconds if one of the following occurs The ignition is turned to ON LOCK is pressed on the remote keyless entry transmitter The front of the power door lock switch is pressed If your vehicle s DE PRS sib the Driver Information Center DI is feature on or program thi off See DIC Vehicle P on page 3 57 3 17 Exit Lighting With exit lighting the interior lamps will come on for about 30 seconds whenever you remove the key f
413. you are driving or when one of the gages shows there may be a problem check the section that tells you what to do about it Please follow this manual s advice Waiting to do repairs can be costly and even dangerous So please get to know your warning lights and gages They re a big help Your vehicle also has a message center that works along with the warning lights and gages See Message Center enten on page 3 43 3 31 Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running You ll know how fast you re going how much fuel you re using and many other things you ll need to drive safely and economically The indicator warning lights and gages are explained on the following pages D SERVICE 1 o 29 190 120 90 20 40 MPH 140 1007 10 20 pii 180 110 120 DRIVER INFO CENTER DE F AVG ECON M im 88 88 8 TRIP United States uplevel shown United States base level and Canada similar 3 32 Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour mph and kilometers per hour km h Your odometer shows how far your vehicle has been driven in either miles used in the United States or kilometers used in Canada However a Canadian odometer will remain in metric units only Your vehicle has a tamper resistant odometer You may wonder what happens if your vehicle needs a new odo
414. ystem with an active subscription and you lock your keys inside the vehicle OnStar may be able to send a command to unlock your vehicle See OnStar System on page 2 32 for more information Remote Keyless Entry System Your keyless entry system operates on a radio frequency subject to Federal Communications Commission FCC Rules and with Industry Canada This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause interference and 2 This device must accept any interference received including interference that may cause undesired operation of the device This device complies with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause interference and 2 This device must accept any interference received including interference that may cause undesired operation of the device Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment At times you may notice a decrease in range This is normal for any remote keyless entry system If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work try this Check the distance You may be too far from your vehicle You may need to stand closer during rainy or snowy weather Check the location Other vehicles or objects m

Download Pdf Manuals

Related Search

Related Contents

Pour la télécharger en format PDF  Samsung BX2350 Vartotojo vadovas  South Shore Furniture 9018045 Instructions / Assembly  _ LL50  Original-Betriebsanleitung Vario Star Raffstore  

Copyright © All rights reserved. Failed to retrieve file