Casio 4734 Watch User Manual
Contents
1. Use and to change the setting e You can specify a value from 0 to 180 in 1 degree units Longitude Value a ja wy mI wy ai Longitude Unit East West Use to switch between east longitude and west longitude 6 Press to exit the setting screen Setting the Analog Time Perform the procedure below when the time indicated by the analog hands does not match the time of the digital display To adjust the analog time 1 In the Timekeeping Mode press seven times to enter the Hand Setting Mode 2 Hold down until the current digital time starts to flash which indicates the setting screen 3 Use to adjust the analog setting e Press once to advance the hands 20 seconds e Hold down to advance the hands at high speed e To lock high speed hands movement hold down to start it and then press to lock The hands will continue to advance for one 12 hour cycle or until you press any button to stop it It will also stop automatically after the time advances 12 hours or if an alarm daily alarm Hourly Time Signal or countdown beeper starts to sound 4 Press to exit the setting screen e The minute hand will be adjusted slightly to match the seconds when you exit the setting screen e To return to the Timekeeping Mode press Hunting Fishing Mode ___ Month Day The Hunting Fishing Mode displays an indicator that Time2. Split Split release Stop Clear SPL displayed Two Finishes D A mD LlLl MCCA Start Split Stop Split release Clear First runner Second runner Display time of finishes finishes second runner Display time of first runner Countdown Timer You can set the countdown timer within a range of one Minutes minute to 100 hours An alarm sounds when the countdown reaches zero e You can also select auto repeat which automatically restarts the countdown from the original value you set whenever zero is reached e All of the operations in this section are performed in the Countdown Timer Mode which you enter by pressing Hours Seconds To use the countdown timer Press O while in the Countdown Timer Mode to start the countdown timer e When the end of the countdown is reached and auto repeat is turned off the alarm sounds for 10 seconds or until you stop it by pressing any button The countdown time is automatically reset to its starting value after the alarm stops e When auto repeat is turned on the countdown will restart automatically without pausing when it reaches zero The alarm sounds to signal when the countdown reaches zero e The countdown timer measurement operation continues even if you exit the Countdown Timer Mode e To stop a countdown operation completely first pause it by pressing and then press This returns the countdown time to its starting value To configure countdown start time
3. graph represents the relative change from one hour to the next e When the relative change from one hour to the next exceeds 10 0 C 18 0 F the dot at the highest point for the applicable hour flashes e When the relative change from one hour to the next exceeds 10 0 C 18 0 F there is no dot in the applicable hour s column e If a measurement error occurs for some reason only a single the dot in the center column will be displayed Temperature change greater Temperature change greater Error than 10 0 C 18 0 F than 10 0 C 18 0 F VI CANE E E E EE 200977 ERIAN Pi ey TY SEGRE EEEE DSDU GC CURE ROH DOGRDHOo5 E Epgg00o7H0HO7Eog goropooggonnonnonnn 000007000E Ll DHPSDRS8 Gee 08o5 CSFB DADAORA SHGSESRERERS Be EHGSEEEER SSSRRe Recalling Temperature Data The measurements the watch takes at the top and the bottom of each hour are stored in memory automatically Memory can hold up to 50 measurement records You can use the Temperature Data Recall Mode to recall memory data when you need it e Each temperature data record has a number The newest data record is number 01 while the oldest data record is the one with the highest number e When there are already 50 records in memory storage of a new temperature reading causes the oldest record record number 50 to be deleted automatically to make room for the new data The new data is assigned record number 1 and all of the numbers of all the other records
4. in accordance with the date year month and day settings e See Daylight Saving Time DST Setting below for details about the DST setting e Any time the seconds setting is changed the analog hands are adjusted accordingly Daylight Saving Time DST Setting Daylight Saving Time summer time advances the time setting by one hour from Standard Time Remember that not all countries or even local areas use Daylight Saving Time To toggle the Timekeeping Mode digital time between DST and Standard Time 1 In the Timekeeping Mode hold down until the seconds start to flash which indicates the setting screen 2 Press once and the DST setting screen appears 3 Press to toggle between Daylight Saving Time 97 displayed and Standard Time fF displayed 4 Press twice to exit the setting screen e The DST indicator appears on the Timekeeping Hunting Fishing Alarm and Hand Setting Mode screens to indicate that Daylight Saving Time is turned on In the case of the Hunting Fishing Mode the DST indicator appears on the hunting fishing level screen only DST indicator On Off status Home Site Data Moon phase the hunting fishing level indicator and Hunting Fishing Mode data will not be displayed properly unless Home Site data UTC differential and longitude is configured correctly e The UTC differential is a value that indicates the time difference between a reference point in Greenwich England and the ti
5. sound whenever the display is illuminated This is due to vibration of the EL panel used for illumination and does not indicate malfunction e Ilumination turns off automatically whenever an alarm sounds e Frequent use of illumination runs down the batteries Auto light switch precautions e Avoid wearing the watch on the inside of your wrist Doing so causes the auto light switch to operate when it is not needed which shortens battery life If you want to wear the watch on the inside of your wrist turn off the auto light switch feature More than 15 degrees e Illumination may not turn on if the face of the watch is too high more than 15 degrees above or below parallel Make sure that the back of your hand is parallel to the ground e Illumination turns off in about one second even if you N keep the watch pointed towards your face e Static electricity or magnetic force can interfere with proper operation of the auto light switch If illumination does not turn on try moving the watch back to the starting position parallel with the ground and then tilt it back toward you again If this does not work drop your arm all the way down so it hangs at your side and then bring it back up again e Under certain conditions illumination may not turn on until about one second after you turn the face of the watch towards you This does not necessarily indicate malfunction of the auto light switch e You may notice a very faint clicking sound com
6. sure that its auto light switch is turned off before riding on a bicycle or operating a motorcycle or any other motor vehicle Sudden and unintended operation of the auto light switch can create a distraction which can result in a traffic accident and serious personal injury To turn the auto light switch on and off In the Timekeeping Mode hold down O for about three seconds to toggle the auto light switch on 8 displayed and off 48 not displayed e The auto light switch on indicator 48 is on the display in all modes while the auto light switch is turned on e In order to protect against running down the battery the auto light switch will turn off automatically approximately six hours after you turn it on Repeat the above procedure to turn the auto light switch back on if you want Reference This section contains more detailed and technical information about watch operation It also contains important precautions and notes about the various features and functions of this watch Moon Phase Indicator The Moon phase indicator of this watch indicates the current phase of the Moon as shown below Moon phase indicator Module 4734 part you cannot see Moon phase part you can see Module 4735 e The Moon phase indicator shows the Moon as viewed at noon from a position in the Northern Hemisphere looking south Note that at times the image shown by the Moon phase indicator may differ from that of the actual
7. 01 to 49 are incremented by 1 becoming 02 through 50 To recall temperature records 1 In the Timekeeping Mode press twice to enter the Temperature Temperature Data Recall Mode Record e This displays the newest record currently in memory number 2 Use to scroll through the records e Pressing O while the oldest record is displayed will scroll to the newest record e If a temperature measurement operation is performed while a record is displayed the displayed record s number will be incremented by 1 e If an error occurs during temperature measurement will be shown for the temperature value in the corresponding record Data storage time Stopwatch Minutes n o lets you measure elapsed time split times and two finishes AE e The display range of the stopwatch is 99 hours 59 minutes 59 99 seconds e The stopwatch continues to run restarting from zero after it reaches its limit until you stop it e The stopwatch measurement operation continues even if you exit the Stopwatch Mode e Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns to elapsed time measurement e All of the operations in this section are performed in the Stopwatch Mode which you enter by pressing To measure times with the stopwatch Elapsed Time D0 0 0 A Start Stop Re start Stop Clear Split Time D AA O o Start
8. MO0605 EA Operation Guide 4734 4735 Getting Acquainted Congratulations upon your selection of this CASIO watch To get the most out of your purchase be sure to read this manual carefully Warning e The measurement functions built into this watch are not intended for use in taking measurements that require professional or industrial precision Values produced by this watch should be considered as reasonably accurate representations only e When hunting or fishing always take proper precautions to ensure your own personal safety and the personal safety of others around you e The hunting fishing level indicator and moon phase indicator produced by this watch are all based on calculations that use the watch s current time date and Home Site settings Because of this you should make sure that the current date and time and your Home Site data are all correct before using the indicators e See the Timekeeping section of this manual for information about setting the current time and date and about specifying your Home Site e Note that the hunting fishing level indicator and moon phase indicator are all based on calculated values They are provided only for reference purposes e CASIO COMPUTER CO LTD assumes no responsibility for any loss or any claims by third parties that may arise through the use of this watch General Guide e Press to change from mode to mode e In any mode except when a setting screen is o
9. Moon in your area e The left right orientation of the Moon phase is reversed when viewing from the Southern Hemisphere or from a point near the equator Moon Phases and Moon Age The Moon goes through a regular 29 53 day cycle During each cycle the Moon appears to wax and wane as the relative positioning of the Earth Moon and Sun changes The greater the angular distance between the Moon and the Sun the more we see illuminated The angle to the Moon in relation to the direction at which the Sun is visible from the Earth This watch performs a rough calculation of the current Moon age starting from day 0 of the moon age cycle Since this watch performs calculations using integer values only no fractions the margin for error of the displayed Moon age is 1 day Thermometer Temperature Sensor Calibration The temperature sensor built into the watch is calibrated at the factory and normally requires no further adjustment If you notice serious errors in the temperature readings produced by the watch you can calibrate the sensor to correct the errors Important Incorrectly calibrating the temperature sensor can result in incorrect readings Carefully read the following before doing anything e Compare the readings produced by the watch with those of another reliable and accurate thermometer e If adjustment is required remove the watch from your wrist and wait for 20 or 30 minutes to give the temperature of the
10. and auto repeat settings 1 While the countdown start time is on the display in the Countdown Timer Mode hold down until the hour setting of the countdown start time starts to flash which indicates the setting screen e If the countdown start time is not displayed use the procedure under To use the countdown timer to display it 2 Press to move the flashing in the sequence shown below and select the setting you want to change Start Time Start Time Auto Repeat Hours Minutes On Off 3 Perform the following operations depending on which setting is currently selected on the display e While the start time setting is flashing use and to change it e Set H I to specify 100 hours e While the auto repeat on off setting Fi or HF is flashing on the display press to toggle auto repeat on 9M and off HE 4 Press to exit the setting screen e The auto repeat on indicator gt is displayed on the Countdown Timer Mode screen while this function is turned on e Frequent use of auto repeat and the alarm can run down battery power Auto repeat on indicator On Off status Alarm Alarm time While the alarm is turned on the watch beeps when the Hour Minutes alarm time is reached You can also turn on an Hourly AM indicator Time Signal which will cause the watch to beep twice every hour on the hour e All of the operations in this section are performed in the Alarm Mode which you ent
11. ding in the on indicator dark The watch s auto light switch turns on illumination automatically when you angle the watch towards your face e The auto light switch must be turned on indicated by the auto light switch on indicator for it to operate e See Illumination Precautions for other important information about using illumination To turn on illumination manually In any mode except when a setting screen is on the display press to illuminate the display for about one second e The above operation turns on illumination regardless of the current auto light switch setting About the Auto Light Switch Turning on the auto light switch causes illumination to turn on whenever you position your wrist as described below in any mode except for the Hand Setting Mode setting screen Moving the watch to a position that is parallel to the ground and then tilting it towards you more than 40 degrees causes illumination to turn on e Wear the watch on the outside of your wrist Parallel to More than ground l 40 Warning e Always make sure you are in a safe place whenever you are reading the display of the watch using the auto light switch Be especially careful when running or engaged in any other activity that can result in accident or injury Also take care that sudden illumination by the auto light switch does not startle or distract others around you e When you are wearing the watch make
12. dney 10 0 11 0 151 E Tokyo 9 0 10 0 140 E Vancouver 8 0 7 0 123 W Wellington 12 0 13 0 175 E City R UTC z eee z Code City Differential Other major cities in same time zone PPG Pago Pago 11 0 HNL Honolulu 10 0 Papeete ANC Anchorage 09 0 Nome YVR Vancouver SFO San Francisco 08 0 Las Vegas Seattle Tacoma Dawson City LAX Los Angeles DEN Denver 07 0 Edmonton El Paso MEX a 06 0 Houston Dallas Fort Worth New Orleans Winnipeg MIA Miami 05 0 Montreal Detroit Boston NYC New York T Panama City Havana Lima Bogota CCS Caracas 04 0 La Paz Santiago Port Of Spain YYT St Johns 03 5 RIO Rio De Janeiro 03 0 Sao Paulo Buenos Aires Brasilia Montevideo RAI Praia 01 0 HS Liskon 00 0 Dublin Casablanca Dakar Abidjan BCN Barcelona PAR Paris Amsterdam Algiers Hamburg Frankfurt Vienna Madrid MIL Milan 01 0 Stockholm ROM Rome BER Berlin ATH Athens JNB Johannesburg IST Istanbul 02 0 Helsinki Beirut Damascus Cape Town CAI Cairo JRS Jerusalem MOW Moscow JED Jeddah 03 0 Kuwait Riyadh Aden Addis Ababa Nairobi THR Tehran 03 5 Shiraz DXB Dubai 04 0 Abu Dhabi Muscat KBL Kabul 04 5 KHI Karachi MLE Male 03 0 DEL Delhi 05 5 Mumbai Kolkata DAC Dhaka 06 0 Colombo RGN Yangon 06 5 SKE Bangkok 07 0 Phn
13. e setting the digital time be sure to first set the UTC differential for your Home Site which is the location where you normally will be using the watch e Note that World Time Mode times are all displayed based on the time and date settings you configure in the Timekeeping Mode To set the digital time and date 1 In the Timekeeping Mode hold down until the seconds start to flash which indicates the setting screen e Be sure to configure the correct UTC differential for your Home Site before configuring any other Timekeeping Mode settings e See the UTC Differential City Code List for information about the UTC differential settings that are supported 2 Press to move the flashing in the sequence shown below to select the setting you want Seconds Temperature Temperature Sensor Unit Calibration T About This Manual e Depending on the model of your watch display text appears either as dark figures on a light background Module 4734 or light figures on a dark background Module 4735 All sample displays in this manual are shown using dark figures on a light background e Depending on the model of your watch the hunting fishing level indicator will show either animal tracks or fish All of the illustrations in this manual show animal tracks e Button operations are indicated using the letters shown in the illustration e For the sake of simplicity the sample displays in this manual do
14. er by pressing Alarm on Hourly time signal indicator on indicator To set the alarm time 1 In the Alarm Mode hold down until the hour setting of the alarm time starts to flash which indicates the setting screen e This operation turns on the alarm automatically 2 Press to move the flashing between the hour and minute settings 3 While a setting is flashing use and to change it e When setting the alarm time using the 12 hour format take care to set the time correctly as a m A indicator or p m P indicator 4 Press to exit the setting screen Alarm Operation The alarm sounds at the preset time for 10 seconds regardless of the mode the watch is in e To stop the alarm tone after it starts to sound press any button To test the alarm In the Alarm Mode hold down O to sound the alarm To turn the Daily alarm and the Hourly Time Signal on and off In the Alarm Mode press O to cycle through the settings shown below Alarm Off Alarm On Alarm Off Alarm On Signal Off Signal Off Signal On Signal On e The alarm on indicator and the Hourly Time Signal on indicator are shown on the display in all modes while these functions are turned on World Time Day of week and day in selected city The World Time Mode digitally displays the current time in 50 cities 30 time zones around the world e The times kept in the World Time Mode are synchronized with the time being kept in the Timekeepi
15. from your wrist place it in a well ventilated location out of direct sunlight and wipe all moisture from the case It takes approximately 20 to 30 minutes for the case of the watch to reach the actual surrounding temperature Temperature Tendency Graph The watch also takes temperature readings at the top and the bottom of each hour and stores the results in memory for display on the temperature tendency graph Depending on the current Timekeeping Mode time the temperature tendency graph shows either the top of the hour measurements or the bottom of the hour measurements for the past 17 hours From the top of each hour to the 29th minute past top of the hour readings are shown in the graph From the bottom of each hour to the 59th minute past bottom of the hour readings are shown in the graph Temperature tendency graph contents are updated every 30 minutes 6 0 to 9 9 C 10 8 to 17 8 F 42 0 to 5 9 C 3 6 to 10 6 F LSTSETee A o rT TDL oa ee 2 3 4 to 3 4 F BRREEEERRREREEEER 5 9 to 2 0 C 10 6 to 3 6 F yA 9 9 to 6 0 C 17 8 to 10 8 F Past 17 hours of measurement values Latest measurement value CASIO Operation Guide 4734 4735 The horizontal axis of the graph represents time The rightmost column is the newest temperature value in memory while the leftmost column is the temperature value stored approximately 17 hours ago 1 dot 1 hour The vertical axis of the
16. ing from the watch when it is shaken back and forth This sound is caused by mechanical operation of the auto light switch and does not indicate a problem with the watch UTC Differential City Code List Site Data List CASIO UTC Differential Site Standard DST Longitude Time Summer Time Anchorage 9 0 8 0 149 W Bahamas 5 0 4 0 77 W Baja California 7 0 6 0 110 W Bangkok 7 0 8 0 101 E Boston 5 0 4 0 71 W Buenos Aires 3 0 2 0 58 W Casablanca 0 0 1 0 8 W Christmas Island 14 0 15 0 158 W Dakar 0 0 1 0 17 W Gold Coast 10 0 11 0 154 E Great Barrier Reef Cairns 10 0 11 0 146 E Guam 10 0 11 0 145 E Hamburg 1 0 2 0 10 E Hong Kong 8 0 9 0 114 E Honolulu 10 0 9 0 158 W Jakarta 7 0 8 0 107 E Jeddah 3 0 4 0 39 E Karachi 5 0 6 0 67 E Kona Hawaii 10 0 9 0 156 W Lima 5 0 4 0 77 W Lisbon 0 0 1 0 9 W London 0 0 1 0 O E Los Angeles 8 0 7 0 118 W Maldives 5 0 6 0 74 E Manila 8 0 9 0 121 E Mauritius 4 0 5 0 57 E Melbourne 10 0 11 0 145 E Miami 5 0 4 0 80 W Noumea 11 0 12 0 166 E Pago Pago 11 0 10 0 171 W Palau 9 0 10 0 135 E Panama City 5 0 4 0 80 W Papeete 10 0 9 0 150 W Rio De Janeiro 3 0 2 0 43 W Seattle 8 0 7 0 122 W Shanghai 8 0 9 0 121 E Singapore 8 0 9 0 104 E Sy
17. l of the current time is 4 or 5 To view the current hunting fishing level and Moon data In the Hunting Fishing Mode press A to toggle between the hunting fishing level screen and the Moon Data screen e The hunting fishing level indicator shows the level for the displayed time The initial hunting fishing level screen shows the level for 6 00 a m The Moon data screen shows the Moon age and Moon phase for the current date Hunting Fishing Moon Data Screen Level Screen Time Month Day Month Day gt oon Press Q Hunting Fishing Moon age Moon phase level indicator indicator e While the hunting fishing level screen is displayed press O to advance to the next hour e While the Moon Data screen is displayed press O to advance to the next day e You can also specify a particular date year month day to view its hunting fishing level and Moon data See To specify a date for more information e When you enter the Hunting Fishing Mode the screen hunting fishing level or Moon data that was displayed the last time you exited the mode appears first To specify a date 1 In the Hunting Fishing Mode hold down until the Year Month Day year setting starts to flash which indicates the setting screen t 2 Press to move the flashing in the sequence shown gt below to select the other settings 3 While a setting is flashing use or to change it e You can s
18. me zone where a city is located e The letters UTC is the abbreviation for Coordinated Universal Time which is the world wide scientific standard of timekeeping It is based upon carefully maintained atomic cesium clocks that keep time accurately to within microseconds Leap seconds are added or subtracted as necessary to keep UTC in sync with the Earth s rotation CASIO Operation Guide 4734 4735 e The Site Data List provides UTC differential and longitude information around the world e The following is the initial factory default Home Site data Tokyo Japan when you first purchase the watch and whenever you have the batteries replaced Change these settings to match the area where you normally use the watch UTC differential 9 0 Longitude East 140 degrees To configure Home Site data 1 In the Timekeeping Mode hold down until the Longitude seconds start to flash which indicates the setting east west screen 2 Press twice to display the UTC differential setting screen and confirm that the setting is correct e If the UTC differential setting is not correct use and to change it 3 Press A to display the longitude value setting screen 4 Press to toggle the flashing between the longitude value and the longitude unit east west Longitude 5 While the setting you want to change is flashing use value and 8 to change it as described below Setting Screen Button Operations
19. n the display press 8 to illuminate the display Hunting Fishing Mode Press Timekeeping Mode OF Hand Setting Mode D ogee Timekeeping Use the Timekeeping Mode to set and view the current time and date This watch features separate digital and analog timekeeping The procedures for setting the digital time and analog time are different e In the Timekeeping Mode press to toggle between the thermometer screen and the temperature tendency screen Thermometer Screen ee i PM Temperature Day of week indicator x Day Temperature ESOC tendency Press graph TL Hour 3f Hunting Fishing Minutes i level indicator Seconds Moon phase indicator e The hunting fishing level indicator indicates the times when game or fish can be expected to be feeding For more information see Hunting Fishing Mode e The Moon phase indicator shows the current Moon phase in accordance with the current date as kept in the Timekeeping Mode e See Thermometer for details about the thermometer screen and temperature tendency graph Important e Be sure to configure the current time and date and your Home Site data data for the site where you use the watch correctly before using the functions of this watch See Home Site Data for more information Setting the Digital Time and Date This watch is preset with UTC differential values that represent each time zone around the globe Befor
20. ng Mode If you feel that there is an error in any World Time Mode time check the UTC differential of your Home Site Data Home City and the current setting of the Timekeeping Mode time e Select a city code in the World Time Mode to display the current time in any particular time zone around the globe See the UTC Differential City Code List for information about the UTC differential settings that are Current time in supported ae selected city e All of the operations in this section are performed in the World Time Mode which you enter by pressing City code To view the time in another city While in the World Time Mode press to scroll eastward through the city codes time zones To toggle a city code time between Standard Time and Daylight Saving Time 1 In the World Time Mode use O to display the city code time zone whose Standard Time Daylight Saving Time setting you want to change 2 Hold down to toggle between Daylight Saving Time DST indicator displayed and Standard Time DST indicator not displayed e The DST indicator is shown on the World Time screen while Daylight Saving Time is turned on e Note that changing the Daylight Saving Time for any city code causes the setting to be applied to all city codes DST indicator CASIO Operation Guide 4734 4735 Illumination This watch has an EL electro luminescent panel that Auto light switch causes the entire display to glow for easy rea
21. not show the analog hands of the watch e Each section of this manual provides you with the information you need to perform operations in each mode Further details and technical information can be found in the Reference section q D Module 4735 Temperature Data Recall Mode on Stopwatch Mode Mode 3 When the setting you want to change is flashing use and to change it as described below Screen To do this Do this ac Reset the seconds to 454 Press O a L DSTI Toggle between Daylight Saving Press O r MIR Time ff and Standard Time fF an Specify the UTC differential Use and annn Change the hour or minutes Use O and a Ef Toggle between 12 hour 1 2H and Press i fmf amp 24 hour ci timekeeping Use and m Change the year month or day e The UTC differential setting range is 12 0 to 14 0 in 0 5 hour units for Standard Time DST turned off and 11 0 to 15 0 in 0 5 hour units for summer time DST turned on e For information about settings other than the time and date see the following Temperature Sensor Calibration Thermometer Temperature Unit To specify the temperature display unit 4 Press twice to exit the setting screen e The 12 hour 24 hour timekeeping format you select in the Timekeeping Mode is applied in all modes e The day of the week is displayed automatically
22. nt press twice to exit the setting screen e The temperature display unit setting you select is also applied to temperature values that are already stored in memory Button Operation Tone Mute indicator The button operation tone sounds any time you press one of the watch s buttons You can turn the button operation tone on or off as desired e Even if you turn off the button operation tone the alarm Hourly Time Signal and Countdown Timer Mode alarm all operate normally To turn the button operation tone on and off In any mode except when a setting screen is on the display hold down to toggle the button operation tone on X not displayed and off gt displayed e Since the button is also the mode change button holding it down to turn the button operation tone on or off also causes the watch s current mode to change e The X indicator is displayed in all modes when the button operation tone is turned off Auto Return Feature e If you leave a screen with flashing digits on the display without performing any operation for two or three minutes the watch saves any settings you have made up to that point and exits the setting screen automatically e The watch will change to the Timekeeping Mode automatically if you do not perform any operation in the Hunting Fishing Mode Temperature Data Recall Mode Alarm Mode or Hand Setting Mode for two or three minutes Scrolling The and buttons are used in various mode
23. om Penh Hanoi Vientiane SIN Singapore HKG Hong Kong 08 0 Kuala Lumpur Taipei Manila Perth Ulaanbaatar BJS Beijing SEL Seoul TYO Tokyo 09 0 Pyongyang ADL Adelaide 09 5 Darwin GJM a 10 0 Melbourne Rabaul NOU Noumea 11 0 Port Vila WLG Wellington 12 0 Christchurch Nadi Nauru Island TBU Nuku Alofa 13 0 e Based on data as of December 2005 The sequence of these city codes is SIN gt JKT e Based on data as of 2003
24. pecify a date in the range of January 1 2000 to December 31 2099 4 Press to exit the setting screen 5 Use to display either the hunting fishing level screen or the Moon Data screen Thermometer This watch uses a temperature sensor to measure temperature A reading is taken during each even numbered minute and the result of the last reading is displayed on the thermometer screen The watch also takes separate readings and stores them in memory for display in the temperature tendency graph which can be viewed in the Timekeeping Mode Measured temperature values are stored in memory for later recall when you need them Thermometer Screen Temperature Temperature Tendency Screen Temperature tendency graph e You can select either Celsius C or Fahrenheit F units for the thermometer screen See To specify the temperature display unit for more information e The thermometer screen displays temperature values in 0 1 C units or 0 2 F units e The display range of the thermometer screen is 10 0 C to 60 0 C or 14 0 F to 140 0 F e You can calibrate the temperature sensor if you feel that the displayed temperature values are not correct See Temperature Sensor Calibration for more information Important e Temperature measurements are affected by your body temperature while you are wearing the watch direct sunlight and moisture To achieve a more accurate temperature measurement remove the watch
25. s and setting screens to scroll through data on the display In most cases holding down these buttons during a scroll operation scrolls through the data at high speed Timekeeping e Resetting the seconds to Hg while the current count is in the range of 30 to 59 causes the minutes to be increased by 1 In the range of 00 to 29 the seconds are reset to A without changing the minutes e With the 12 hour format the P PM indicator appears on the display for times in the range of noon to 11 59 p m and the A AM indicator appears for times in the range of midnight to 11 59 a m e With the 24 hour format times are displayed in the range of 0 00 to 23 59 without any indicator e The year can be set in the range of 2000 to 2099 e The watch s built in full automatic calendar makes allowances for different month lengths and leap years Once you set the date there should be no reason to change it except after you have the watch s batteries replaced World Time e The seconds count of the World Time is synchronized with the seconds count of the Timekeeping Mode e All World Time Mode times are calculated from the current time in the Timekeeping Mode using UTC time differential values CASIO Operation Guide 4734 4735 Illumination Precautions e The electro luminescent panel that provides illumination loses power after very long use e Illumination may be hard to see when viewed under direct sunlight e The watch may emit an audible
26. shows as one of five levels the suitability of a specific date and time minute 00 to minute 59 of a particular hour for hunting or fishing This mode also can be used to display Moon Data Moon age and Moon phase for a specific date e If you suspect that the hunting fishing level indicator or current Moon data is wrong for some reason check the current Timekeeping Mode settings time date and HUNT FISH Home Site and correct them if required indicator e See Moon Phase Indicator for information about the Moon phase Moon phase indicator indicator e All of the operations in this section are performed in the Hunting Fishing Hunting Fishing Mode which you enter by pressing level indicator Hunting Fishing Level Screen Hunting Fishing Level Indicator The hunting fishing level indicator shows the relative favorability of a hunting fishing time calculated in accordance with Moon transit and phase as shown in the table below Module Level5 Level4 Level3 Level2 Levelt Upper Moon Phase Lower New moon First quarter omer tees leez leei These indicators actually appear during Moon ages 13 0 to 16 6 Full Moon and phase immediately preceding it and 27 7 to 1 8 New Moon and phase immediately preceding it e The hunting fishing level indicator changes in accordance with the Moon data e In the Timekeeping Mode the HUNT FISH indicator flashes whenever the hunting fishing leve
27. watch time to stabilize To calibrate the temperature sensor 1 In the Timekeeping Mode hold down until the seconds start to flash which indicates the setting screen 2 Press nine times to display the temperature sensor calibration screen 3 Use and to change the calibration value e You can change the value in 0 1 C 0 2 F steps ina range of 10 C 18 F The calibration value shows when the setting is outside the allowable range Calibration value e To return the calibration value to its default no calibration indicated by press O and at the same time e Temperature sensor calibration will not be possible if the current reading is outside the allowable display range 10 0 C 14 0 F to 60 0 C 140 0 F and the calibration value shows e Setting a sensor calibration value does not affect temperature values that are already stored in memory 4 After configuring the setting you want press twice to exit the setting screen To specify the temperature display unit 1 In the Timekeeping Mode hold down until the seconds start to flash which indicates the setting screen 2 Press 10 times to display the temperature unit setting screen 3 Use to switch between Celsius 9 and Fahrenheit OC e The initial factory default and the initial default after Temperature unit battery replacement is Celsius Tf 4 After configuring the setting you wa
Download Pdf Manuals
Related Search