ATD Tools ATD-5900 Baby Jumper User Manual
Contents
1. then and only then will it deliver the voltage to the clamps Do not smoke use matches use a cigarette lighter or allow a spark or flame near the battery Do not allow metal to come in contact with the battery poles It may spark or short circuit the battery and cause an explosion Remove any and ALL jewelry and watches when working with a Li Fe battery Stop using the jumpstart when you hear the alarm or when indicating LED 6 is on The reason may be from 1 The voltage is less than 8V Charge the jumpstart to prevent battery failure 2 The temperature is higher than 140F 60C Cool the jumpstart to at least 104F 40C 3 The jumpstart is connected backwards incorrectly connected or short connected Correctly connect the clamps 3 Pro Lithium Jumpstart Features 1 Emergency LED light Switch 2 Emergency LED light 3 12V output 4 Full charge LED 5 50 capacity LED 6 Charge Low voltage alarm Over temp indicator 7 Clamp correct connection indicator 8 Reverse connection indicator 9 Incorrect connection indicator 10 USB 5V DC output outlet 11 Test USB output Switch 12 Charger input outlet 5 4 4 USING THE BOOSTER FUNCTION WARNING Ensure that you are using this on a 12 VOLT SYSTEM ONLY otherwise the battery could explode Please strictly follow the following steps otherwise it could cause damage to the jumpstart the vehicle or personal injury or death 1 Turn the vehicle ignition and subsid2. 8 hours 7 6 4 LED indicator 4 indicated a full charge 5 Disconnect the charger 6 In order to achieve maximum battery life it is recommended to use your jumpstart often so that the capacity of the battery is protected and its life expectancy will be extended 6 USING THE 12V DC POWER SOURCE 1 Open the cover of cigarette lighter socket on the front of the jumpstart 3 2 Plug the jack plug of 12v electrical appliances into the cigarette lighter socket Note The maximum power of the cigarette lighter is 150W If the power of your appliance is more than 150W the socket output will shut down automatically and will recover in 30 seconds 7 USING THE USB PORT AND LED WORK LIGHT 1 Push the test USB switch button 12 one time to turn on the USB 10 outlet Push again to switch it off If the battery is less than 10V the USB output will turn off automatically 2 Push the light switch button 1 one time to turn on the LED work light Push again to turn it off 8 MAINTENANCE 1 Always inspect the power station before use to ensure the cables are in perfect condition and the clamps are clean and free from corrosion 2 Keep your jumpstart clean by wiping with a dry cloth DO NOT use solvents as a cleaning agent 3 Keep your jumpstart at HIGH or FULL CHARGE status at all times 9 PARTS
3. ATD 5900 Manual Weight 7 71 lbs 3 5Kg Product Size 9 25 x 9 25 x 7 5 235 x 235 x 190mm Functions 700A Cranking Amps 12V DC Output with 15A overload protection High Intensity LE D USB 5VD C 2 1 A Battery Lithium Iron Charging 12V 1A Charger Accessories Cigarette socket Charger I nstruction Manual 1 Features Used to start 12V vehicles without the use of other vehicles or AC power supplies Reverse connection alarm short circuit alarm low voltage alarm and over temperature alarm 12V DC cigarette power outlet with overload protection provides power for appliances designed to plug into vehicles 12V power source High intensity LE D emergency light can be used for emergency repairs or other emergency situations Li Fe Lithium Iron Battery with more powerful performance needs no attention other than charging 12V 1A adaptor with automatic overcharge protection 5V 2 1A USB provides power for small electrical appliances MP3 player etc LE D shows the internal battery status High strength Polypropylene housing 1112 1 3 2 2 WARNING Before using the jumpstart read and follow the instructions carefully Also pay close attention to the cautionary statements on the vehicles battery and any other equipment you be using As a safety measure there is NO VOLTAGE present at the clamp ends The ATD 5900 automatically detects when it is hooked up correctly to a battery
4. cles engine starts disconnect the black clamp first and then disconnect the red clamp Re wrap the cables after each use 13 After use always recharge the jumpstarts battery fully 14 Frequently test the battery s voltage and recharge it when 5 or 6 LED is on 15 Low temperature start performance of the Li Fe battery will be affected at temperatures lower than 10C 14F After a few attempts to start the battery should warm up and produce more cranking amps While this isn t the case with typical Sealed Lead Acid batteries this is normal for Li Fe batteries 5 Charging using the AC adaptor CAUTION 1 Use only the charger included with your jumpstart to recharge this jumpstart Non standard products will shorten the life of the battery and void the warranty 2 Charge your jumpstart battery for 8 hours before using for the first time 3 After using press the test USB switch button 11 check the battery voltage by Indicating LED s 4 5 amp 6 if the indicating LED 5 or 6 are on it means the battery must be recharged 4 Recharge the jumpstart battery after each use if possible and thereafter at least every 6 12 months How to charge 1 Plug the charger into 110V AC power outlet 2 Plug the connector into the socket 12 located in side of the jumpstart The charging indicating LED light 6 indicated the jumpstart is charging 3 Depending on the use of the jumpstart charging time is approximately 6
5. iary equipment off 2 DO NOT touch the red positive clamp against the black negative clamp 3 Ensure the area is well ventilated 4 Connect the red positive clamp to the battery positive terminal first Be sure that the clamp does not contact any moving parts or fuel lines 5 Connect the black negative clamp to a suitable ground on the vehicle chassis 6 If there is a reverse connection between positive and negative poles the jumpstart emits an audible alarm the red LED 8 will be on indicating the reverse connection Please adjust the positive and negative polarity 7 If connected incorrectly to a vehicle that uses a 24v system the jumpstart emits an audible alarm the red LED 9 will be on indicating the incorrect connection this jumpstart will not work in this situation Only use on vehicles with a 12v system 8 If connected incorrectly to a vehicle that has a 6v system it won t send out any alarm information Attempting to start your 6v system with this jumpstart will cause damage to the jumpstart and the vehicle Only use on vehicles with a 12v system 9 With the correct connection LED 7 will be on now you can start the car If the battery internal and external voltage is less than 8v it will shut off automatically 10 Do not try to start the vehicle for more than 5 seconds at a time 11 If the engine does not start properly wait at least 3 minutes before attempting to restart 12 After the vehi
Download Pdf Manuals
Related Search