Ariston AW122 Washer User Manual
Contents
1. din gt 2 54 cm lt 1in lt a Deco 12 Installation Requirements Tools and Parts Assemble the necessary tools and supplies before beginning the washer installation The parts supplied are in the drum Tools needed for installation 10mm Wrench Screwdriver U Clamp If You Have No access to Hot Cold water hookups Transit Bolt Hole Plugs 4 You ll Need to Buy Splendide Faucet Adapter kit Part No 154187104A 8ft 2 4m Water damage Concerns Splendide Drain A Way Pan Part No PI 22 PI 24 or similar Floor drain Siphon break kit sold at most hardware stores Disposer drain Y connector sold at most hardware stores Shifting Concerns RV and Marine Installations Splendide SecureFit installation Brackets Part No MKO1 Keeps washer in place dur ing travel to prevent Kinked inlet hoses Disconnected dryer vent hoses Crushed dryer vent hose e Blocked dispenser drawer Knobs rubbing against closed doors Scuffed cabinet woodwork All Splendide parts are available direct from Westland Sales 1 800 356 0766 ARISTON Location Selecting the proper location for the washer dryer improves performance and minimizes noise Proper installation is your responsibility The washer dryer can be installed under a counter in a closet in an alcove or in a recessed area with minimum installation clearances of 02. it is recommended that a qualified electrician determine that the ground path is adequate Do not ground to a plastic plumbing lines gas lines or water pipes Check with a qualified electrician if you are not sure the washer is properly grounded DO NOT use an extension cord DO NOT have a fuse in the neutral or ground circuit DO NOT install or store this appliance where it will be exposed to weather or in an area where gasoline or other flammables are stored 15 Installation Instructions A WARNING EXCESSIVE WEIGHT HAZARD Use two or more people to move and install the washer dryer Failure to do so can result in back or other injury Remove the Transit Screws Spacers First position the washer so that the rear of the unit is within approximately 3 feet 90 cm of the final location There are 4 bolts in the rear panel of the washer that sup port the suspension system during transportation 1 Using a wrench loosen each of the bolts 2 Once loosened pull out the bolt including the rubber grommet and the plastic spacer covering the bolt 3 Once all 4 bolts are removed close the holes with the transit bolt hole plugs provided 4 Keep the bolts rubber grommets and plastic spacers in a safe place These items should be reinstalled if the machine is transported in the future IMPORTANT Transit Screws Spacers must be removed before use 16 Route the Drain Hose Prop
3. 12 hours so laundry is ready when you are Cancels Interrupts the selected program Wait 5 seconds for the ON OFF light to stop flashing 4 Rotate the PROGRAMS dial clockwise and select a washing program 1 Rotate the PROGRAMS dial clockwise to a Stop Reset position 2 Wait 5 seconds 3 Rotate the PROGRAMS knob to the desired washing program or Drain see right a Delay Start has been set The door can be opened or closed at any time before the cycle begins To cancel a program completely select kyd Drain After the washer drains wait for the DOOR LOCK light to extinguish before attempting to open the door Dispenser Drawer Automatic Dispenser Drawer Once loaded in the proper compartment s in the dis penser drawer Detergent Fabric Softener and Bleach will automatically be added at the appropriate time during the washing program Dispenser Compartments above ARISTON HE Laundry Powder For best results use HE High Efficiency detergent HE laundry detergents dissolve more quickly in less water and won t overfoam in front loading washers Splendide All Natural Premium Laundry Powder Part No 1005 About Using Bleach Compartment 4 Bleach can only be used when HOT is selected on the TEMPERATURE knob If bleaching is necessary the Bleach Compart ment 4 provided must be inserted into com partment 1 Always dilute bleach before using If used you will see water in
4. Owners Manual It will show you ways to best utilize your valuable purchase Start and Programs Choosing a program 1 Plug the washer into the electrical socket SPIN SPEED knob e To further customize the program press 2 Sort your laundry according to similar colors one of the four WASH OPTIONS buttons fabrics and degree of soil For best results see Washing Options do not load more than the maximum capacity 6 Open the dispenser drawer and add laundry aids Fabric Maximum Load see Dispenser drawer Cottons 12 Ibs Synthetics 6 Ibs Note If your previous washing machine was a Delicate Fabrics 5 Ibs top loader initial loads may require little to no Wools 3 Ibs detergent Old detergent trapped in the clothes Bathrobes 5 lbs will be released during the tumble action 3 Open the door Load the machine and make sure 7 Close the dispenser drawer the items are not in the way of the door seal 8 Press the ON OFF button in to begin 4 Close the door During the washing program you cannot open the door 5 Choose the wash program by checking the i Programs table see Preset Washing Programs 9 When the cycle is complete wait for the DOOR as well as the fabric care tags found on your LOCK Light to extinguish Open the door and clothing take your laundry out e Select a washing cycle by rotating the 10 Unplug the washer PROGRAMS dial clockwise e Set the wash water temperature with the e TEMPERATURE knob e Se
5. before operating Failure to do so can result in death or electrical shock 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Under certain conditions Hydrogen gas may be pro duced in a hot water system that has not been used for 2 weeks or more HYDROGEN GAS IS EXPLOSIVE If the hot water system has not been used for such a period before using a washing machine turn on all hot water faucets and let the water flow from each for several minutes This will release any accumulated Hydrogen Check the Coin Trap every few months to remove coins buttons or similar size objects This appliance must be properly grounded see Grounding Instructions Clothes cleaning rags mop heads and the like which have traces of any flammable substances such as veg WARNING EXCESSIVE WEIGHT HAZARD Use two or more people to move and install the washer dryer Failure to do so can result in back or other injury etable oil petroleum based oils or distillates etc must not be placed in the washing machine These items may contain flammable substances after laundering which may smoke or catch fire by itself Always be sure to unplug the washing machine from the electrical supply before attempting any service Do not insert pull out the mains plug with wet hands Do not pull out the mains plug by tugging the cable Do not use an extension cord or an adapter to connect the washing machine to
6. out before washing e Tie all strings before loading 5Heavy Heavily soiled 80 minutes 800rpm Baby linen etc colorfast synthetics 6 Regular Delicate color 65 minutes 800 rpm e All types of slightly soiled synthetics synthetics 7 Light Delicate color 40 minutes 800 rpm e All types of slightly soiled synthetics synthetics e All types of delicate items e Place underwear tights 8Light Delicate items 64 minutes 600 rpm stockings and other delicates in a linen bag 9 Silk Particularly delicate 60 minutes No Spin e Curtains silk viscose items 10 Wool Wool 65 minutes 600 rpm Wool scarf sweater etc hand washables Turn knit items inside out Use very little detergent 3 Ib max load Please Note cycle times will vary according to size and fabric type of load water system temperature and room temperature DO NOT wash torn frayed or non hemmed items Symbols Key Empty all pockets before loading the laundry e Stop Reset Spin Cycles 10 13 min Easy iron Anticrease Stop t Drain Only amp Fabri No Spin c Softener Only Cycle YE Rinse Cycles 25 min Start and Programs Washing Options Option What it does How to set it Note Changes the preset wash water temperature of the selected Rotate TEMPERATURE knob to the desired wash Rinse water is always COLD TEMPERATURE program temperature Select IN for No Spin Changes excludes the preset e Faster spi
7. sides 1 front back You ll Need A water heater set to deliver 120 F 49 C water to the washer A grounded electrical outlet located within 6 ft 1 8m of where the power cord is attached to the back of the washer See Electrical Requirements Make sure the electrical socket is accessible so you can unplug the washer when not in use Hot and cold water faucets located within 8ft 2 4 m of the hot and cold water fill valves and water pressure of 7 5 100 psi A solid level floor that can support at least 280 Ibs 127 kg DO NOT install on carpet The ma chine must rest solid on a sturdy floor for optimum performance and minimum vibration Enough space to open the door fully so you can load and unload easily RV Marine Installations When locating the appli ance in a towable trailer or watercraft position the machine over the axles or mid ship where move ment is at a minimum Block the machine to prevent extreme movement or tipping Water Inlet Requirements Water pressure must range within 7 5 and 100 psi If the water pipes are new or left unused before con necting the machine run the water until clear to remove debris Connect the inlet hose to a cold water tap having a 3 4 BSP thread Ensure that there are rubber washers at the end of each inlet hose The L Shaped end goes on the machine and the straight ends on the water faucets CAUTION 1 This washing machine must only be opera
8. the Bleach compart ment after the washing program is complete This is normal Bleach cannot be used during the Silk washing program Using the Bleach compartment excludes the possibility of using the PreWash cycle DO NOT exceed the Max level shown above If you overfill the bleach dispenser bleach will run directly into the machine and may possibly 1 Detergent for Pre Washing powder only 2 Detergent for Washing powder or liquid 3 Liquid Fabric Softener 4 Liquid Bleach Laundry Aid Amount 1to2 Powder Detergent Tablespoon s damage clothes Special Note Powder detergent is recommended to Liquid Detergent Tablespoon If using liquid detergent ALWAYS add detergent to compartment no more than a few seconds before the start of the wash cycle 2 to1 Tablespoon Liquid Fabric Softener Using a liquid fabric softener or a detergent with a built in soft ener fluffs clothes This helps speed drying times and reduce wrinkles Fabric perfumes can be used in this compartment Using more than the recommend ed amount of fabric softener can impair wash results Bleach Max level Detergent Facts Never use too much detergent or additives Using too much will cause excessive sudsing and scaling which may reduce perfor mance and cause possible damage to your washer NEVER use detergent for hand washing or a detergent that is not designated for machin
9. 3 656 2280 11 Technical Details Technical Details Recessed closet and alcove installation Instructions Model AW122 Dimensions 23 59 5cm wide The machine may be installed in a 32 34 85 cm high recessed area closet or alcove With legs screwed all 22 1 7 53cm deep The installation spacing is in inches and isthe the way in minimum acceptable Additional spacing should be considered for easy installation servicing and Capacity 2 to 12 Ibs 7 kg compliance with local codes or ordinances Other installations must use the minimum dimensions Electric 120 V 60 Hz min working 108V indicated Connections max absorbed power 1350 W 12 A Additional clearances for wall door and floor Water max pressure 100 psi 689 6 kPa moldings may be required Connections min pressure 20 psi 137 9 kPa Spin Speed up to 1200 rpm Minumum Clearances This appliance was tested by UL Sides 0 and conforms with both Canadian Front Back 1 eus LISTED and U S UL safety requirements and displays their Mark ur Indesit Company offers their Front View customers products with the Energy ENERGY STAR Star label As a result of technological progress the manufacturer reserves the right to make any improvements to its appliances without giving prior notice to its clientele Oin gt r Oin 0 cm gt 0 cm Side View L
10. Brackets Part No MKO1 DID YOU KNOW The majority of problems with noisy machines or excessive vibration are due to the transit SCREWS SPACERS NOT BEING REMOVED or the FEET NOT BEING ADJUSTED correctly to level the machine 17 Installation Instructions Complete the Installation Check to be sure all parts are now installed If there s an extra part go back through the steps to see which step was skipped Check to be sure you have all your tools Dispose recycle all packaging materials Read this manual Final Installation Checklist M Instructions and Installation Kit have been re moved from the tub Vl Transit bolts spacers have been removed MI Washer is plugged into electrical outlet and is properly grounded M Water hoses are connected to the faucets with inlet screens and washers M Water is turned on and checked for leaks at faucet and water valve connections MT Drain hose is properly located into drain facility and is not collapsed or damaged M Washer has been leveled MI Test for proper operation see below To test and clean the washer Measure 1 to 2 tbsp of powdered High Efficiency HE detergent e Pour the detergent into compartment 2 in the dispenser drawer see Dispenser Drawer Select program 4 on the PROGRAMS dial Select HOT on the TEM PERATURE knob Splendide All Natural Pre e Press the ON OFF button ae ee ae Fe in Allow the washer to ar Avallabie From
11. Care Use and Installation Booklet English AW122 A ARISTON FRONT LOADING WASHER Contents Warnings and Safety Instructions 2 Important Safety Instructions Washer Description 3 The front the back Control panel Start and Programs 4 6 Choosing a Program Table of control panel lights Table of preset wash programs Table of washing options Dispenser 7 Automatic dispenser drawer Dispenser compartments About using bleach Table of laundry aids Maintenance and Care 8 9 When to switch off electricity and water faucets After washing is complete Clean the exterior interior amp dispenser drawer Clear the coin trap Check the rubber inlet hoses yearly Winterization Troubleshooting 10 11 Spare parts Technical Details 12 Recessed closet alcove installations Installation Requirements 13 15 Tools and Parts Location Water Inlet Requirements Drain System Requirements Electrical Requirements Installation Instructions 16 17 18 Remove Transit Screws Spacers Connect the Inlet Hoses Route and Secure the Drain Hose Level the Washer Final Installation Checklist Warnings and Safety Instructions The machine was designed and built in compliance with the appliance international safety regulations The information on this page is provided for your safety and should be read carefully WARNING To reduce the risk of fire electrical shock or injury to persons when using your appliance follow basic preca
12. F Button IN Wait 1 2 minutes Press ON OFF Button OUT Unplug washer dryer from electrical outlet or disconnect power Turn water supply faucets OFF Disconnect inlet hoses from faucets Drain remaining water from the hoses FINISHED Optional RV Winterization if currently PUMPING antifreeze 1 2 3 4 5 6 7 8 9 through a fresh water system With machine power OFF turn WASH TEMP knob to HOT Advance Program Dial to cycle 3 Press ON OFF button IN Let machine fill until antifreeze is in the drum Advance Program Dial to e RESET Wait 5 seconds Advance Program Dial to a Spin position Let the antifreeze drain from the drum Advance Program Dialto RESET Wait 5 seconds Press the ON OFF button OUT Turn WASH TEMP knob to COLD Repeat steps 2 through 7 FINISHED 1 2 3 4 5 ARISTON B To use again flush water pipes then Reconnect water inlet hoses to corresponding HOT COLD faucets Turn faucets ON NOTE Check water inlet hoses and pump periodically see Us ers Guide Plug washer dryer in to appropriate electrical out let see Users Guide or reconnect power supply With ON OFF button in the OFF OUT position pour 2 TBSP of powder detergent or liquid equiv into the Detergent compartment inside the Dispenser Drawer see Users Guide Advance Program Dial to cycle 4 Press ON OFF button IN Allow machine to run throug
13. Splendide Westland Sales complete the full cycle It will take approx 40 min 18 A WARNING ELECTRICAL SHOCK HAZARD Plug washer dryer into a grounded 3 prong outlet Do not remove ground prong Do not use adapter Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock IMPORTANT Should you move residence in the future the Transit Screws Spacers should be reinstalled to support the inside of the washer and prevent damage WHEN TRANSPORTING Notes ARISTON OWN liane Copyright 2006 Westland Sales Clackamas OR 97015 1 800 356 0766 www westlandsales com
14. e Easy Iron function is selected see Washing Options The washer The Coin Trap is clogged see Clear the Coin Trap does not drain or spin The drain hose is kinked or squashed The drain hose is clogged or positioned incorrectly so it is blocking water flow The washer vibrates excessively during the spin cycle The shipping bolts and spacers have not been removed The washer is not leveled correctly The washer leaks The inlet hoses are not secured properly They should be tightened by hand but not forced The detergent dispenser needs to be cleaned see Clean the Detergent Dispenser The drain hose is not secured properly There is too much foam Improper detergent for this washer see Dispenser Drawer Too much detergent has been used see Dispenser Drawer To clear excess suds set the Programs dial to Rinse and allow the machine to rinse out If you still have a problem call Westland Sales 1 800 356 0766 Please have the following info ready when you call 1 Nature of the malfunction 2 Model no AW122NA 3 Serial number i e S N 10 Spare Parts ARISTON This washer is a complex machine Repairing it yourself or having a non authorized person try to repair it could cause harm to one or more persons and to the machine and could invalidate the warranty Always call Westland Sales first if you experience any problems with this machine Contact number 1 800 356 0766 or 50
15. e use When washing in COLD water reduce amount of detergent Maintenance and Care When you should switch off the electricity and turn off the water faucets Unplug the washer and turn off the water faucets when not using it when cleaning it and during maintenance activities After washing is complete always Turn off the water faucets to relieve pressure on the inlet hoses Wipe the inside of washer door with a soft cloth Clean the Exterior As needed clean the exterior with a rag dipped in luke warm water and soap Never use polish of any kind Clean the Interior In hard water areas or where heavily soiled items are frequently washed you may periodically need to remove body oils or detergent that has accumulated in the drum To remove this build up run the washer through a complete cycle using HOT water and 2 cups of anon precipitating water softener Periodically apply a thin coat of paste wax to the inner door especially the area that is immediately next to the door window to protect it from laundry aid spills and discoloration Clean the Dispenser Drawer As needed rinse buildup of detergent or other laundry aids from the dispenser drawer To remove the dispenser drawer pull it outwards as indicat ed in the picture Then leave it under warm running water for a few minutes Clear the coin trap This washer contains a self cleaning pump that does not require any cleaning or maintenance Howe
16. er routing of the drain hose protects your floors from damage due to water leakage Carefully read and follow these instructions The drain hose is connected to the washer To prevent ain water from going back into the washer Do not straighten the drain hose and do not force excess drain hose into the standpipe Hose should be secure but loose enough to provide a gap for air When routing the drain hose through cabinets or walls use a protective material such as electrical tape to cover sharp edges that could damage the hose f 3 Drain Hose Connect the Inlet Hoses Before connecting any hoses run the faucets until the water is clear to remove any debris Make sure the drum is empty Please use the new hoses supplied Old hoses may cause leaks due to worn out washers or may be split due to water pressure 1 Connect the angled ends of the hoses to the inlet valves at the back of the machine 20mm threads Screw on the couplings BY HAND until they are seated on each gasket Installation Instructions 2 Attach the hose connected to the H valve to the hot water faucet Screw on the coupling BY HAND until it is seated on the gasket DO NOT OVERTIGHTEN 3 Attach the hose con nected to the C valve to the cold water faucet Screw on the coupling BY HAND until it is seated on the gasket DO NOT OVERTIGHTEN 4 Turn on the water faucets and check for leaks IMPORTANT The couplings should be tighte
17. h complete cycle to clean out any remain ing antifreeze FINISHED Troubleshooting Before you call our Customer Care Department go through the following troubleshooting suggestions Problem The washer won t start Possible Causes Solutions The plug is not plugged into the socket or not making contact There has been a power outage The fuse has blown The door is not closed securely The ON OFF button is not pressed in The Programs dial has not been set correctly see Preset Washing Programs The water supply faucets are not turned on The washer won t fill The hose is not correctly connected to the tap The inlet hose filter screens need to be cleaned If work has recently been carried out on the water piping or if water is very hard the filters could be clogged with particles or debris The rubber hoses are kinked or squashed The Programs dial keeps turning Wait for the washer to drain then Stop Reset the washer see Washing Options Set another program If the knob continues to turn contact our Customer Care Department The washer is continuously filling and draining with The drain hose is positioned too low It must be installed at a height ranging from 25 to 34 The end of the drain hose is under water The wall drainage system does not have a breather pipe water There may be a problem with your drain trap if the washer is installed on an upper floor of a building Th
18. ned BY HAND a tool should only be used if a leak occurs Do not use excessive force Secure the Drain Hose 1 Drape the power cord over the washer top 2 Secure the drain hose to the laundry tub leg or standpipe with a strap or cable tie 3 Use the U Clamp provided and insert the drain hose into the standpipe or sink DO NOT force excess drain hose into the standpipe There should be only 6 of drain hose in the stand pipe 6 max i 25 62 cm min 34 86 cm max 20 50 cm min with an air break Standpipe ARISTON Level the Washer Dryer After positioning the washer in it s final installation location you must level the washer The front feet are self locking and adjustable Your machine will be noisy if the two front feet are not adjusted so the machine stands firm and level 1 Tilt the machine back leaning it against the wall 2 Adjust the front feet up or down to ensure the washer is resting solid and does not rock side to side or front to back when the machine is upright IMPORTANT When moving washer to it s final location take care not to kink the inlet or drain hoses Optional Splendide SecureFit Installation Brackets Part No MKO1 Hook around two front feet and screw into the floor Designed to keep the washer from shifting front to back or left to right Recommended for RV or Marine Installations SecureFit
19. nning will SPIN SPEED spin cycle of the selected Rotate SPIN SPEED knob extract more water to the desired speed program from highly absorbent fabrics Adds a one hour soak to the Press e During soaking laun Soaking selected washing program SOAKING button in dry is gently tumbled e Recommended for Adds one extra rinse to the Brake very large loads when Extra Rinse selected Cotton Heavy Duty or EXTRA RINSE button in too much detergent is Permanent Press program used or for detergent contact allergies Press Prevents wrinkles EASY IRON button in caused when laundry is Automatically stops the selected Program will stop when it not removed promptly Permanent Press or Hand f had habl befi reaches the 4 symbol on rom the drum Easy Iron Was 296S program Deore the Programs dial Use this option when the spin cycle begins Laundry k p soaks in water until the Easy Totelmetheprogiam ie ce 1 V Iron button is pressed again Press EASY IRON button iaundey until lena atest again out the cycle is finished Adds an extra wash to the ee is Pre Wash selected program press FAVE de Me PRE WASH button in like work clothes or Not available in Wool cycle children s clothes 1 Rotate PROGRAMS dial clockwise and select 1h The On Off lamp will 3h 9h or 12h flash 1 second on 4 DELAY TIMER Delay the start of the Press ON OFF button in seconds off to indicate Stop Reset washing program by 1 3 9 or
20. r than 34 86 cm from the bottom of the washer faucet and discharges water directly into the sink e Designed for installations where washer dryer hookups fe max are not available Faucet Adapter Kit Part No 25 62 cm min 154187104A 34 86 cm max he a A Splendide Drain A Way g with an air break Pan Part No PI 24 PI 22 R e Durable rotomolded pan with seamless construction and reinforced corners Fits under the washer Hs oe ioe a siphon break that may Designed to protect against de RER water damage in the event of overflow or flooding The sink drain system connected to a garbage disposer g er Panypareio requires a Y connector sold separately 14 Installation Requirements Electrical Requirements GROUNDING INSTRUCTIONS Electrical Shock Hazard Death Fire or Electric Shock This appliance must be grounded This appliance should be connected to an Individual Branch Circuit with N 14 AWG Wire and Protected by 15A fuse In the event of a malfunction or breakdown grounding will reduce the risk of electric shock by providing a path of least resistance for electric current This appliance is equipped with a cord having an equipment grounding conductor and grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances DO NOT modify the plug provided
21. t the high spin speed with the Lights Light What it means Note e The door will stay locked for up to 2 minutes after the DOORLOCK Indicates when the Light ON Locked program is completed door is locked e Light OFF Unlocked NEVER attempt to open the door when the DOOR LOCK light is ON e Slow Flash Ready awaiting This washer can perform self instructions diagnostics in the event of a Solid Light Program problem If needed this light ON OFF Indicates te status accepted in operation will indicate a fault code by of the washer Quick Flash P displaying a specific series of eee RE Mo blinking lights competed but door still locked Start and Programs Preset washing programs Program Clothing Type Description High Spin ARISTON Recommendation 120 minutes Heating element is used to reach Eliminates harmful bacteria and safely deep cleans stained cotton 1 Sanitary Colorfast Items 1200 rpm colorfast items o 1589F wash temp e The heating element will Bleach option not take about 10 minutes to available reach full heat 2Heavy Exceptionally soiled whites 90 minutes 1200 rpm Sheets tablecloths etc 3 Regular Heavily soiled e Jeans towels etc whites and colorfast 50 minutes 1200rpm Fasten all hooks zippers colors and buttons 4Light Slightly soiled 40 minutes 1200 rpm e Shirts sweatshirts etc whites and delicate e Turn printed shirts inside colors
22. ted with cold and hot tap water Do not connect the appliance to a mixer tap of an unpressured hot water boiler 2 To prevent water damage the hot and cold water valves should be accessible when the washer is in place and should always be turned off when the washer is not in use 13 Installation Requirements Drain System Requirements The washer dryer can be installed using the standpipe Sink Drain W Y Branch Tailpiece Laundry Sink Drain drain system floor drain system or the sink drain system To prevent siphoning the outlet end of the drain hose provided with unit MUST be at least 20 50 8 cm above the base of the machine Not more than 6 15 24 cm of the drain hose should be inserted into the drain pipe 25 62 cm min with an air break Floor Standpipe Wall Standpipe i ee Cable tie Y y Tail Piece 20 51 8 cm min This connection MUST be 34 86 cm max before drain trap and at least 20 50 8 cm above the floor where washer will be installed Standpipe A amp B 25 62 cm min 34 86 cm max Floor Standpipe w Y Branch Tail Piece The standpipe drain requires a minimum diameter stand Optional pipe of 1 1 4 3 2 cm The minimum carry away capacity Splendide Faucet Adapter can be no less than 7 gal 26 5 L per minute The top of Kit Part No 154187104A the standpipe must be at least 25 in 62 cm high and no e Supplies water from the highe
23. the electrical power supply Caution when draining hot water The washing machine must only be used for it s in tended purpose Make sure drum is empty before loading washer Make sure that all water connections to the wash ing machine have shut off valve s and that they are readily accessible Close the washing machine shut off valves at the end of each wash day Check the fill hose connections on a regular basis to assure that they are tight and not leaking Do not machine wash fiberglass materials Small par ticles can stick to fabrics washed in following loads and cause skin irritation Check the inlet hoses periodically for bulges kinks cuts wear or leaks and replace them every five years SAVE THESE INSTRUCTIONS Washer Description ARISTON Control panel Hot and cold Dispenser drawer water inlet Model No En Power cord l a Serial No Sy Drain hose Transit bolts Coin Trap Extra Rinse f Programs dial Program key Easy Iron Pull on Grey Tab ON OFF Soaking PreWash D O he ir ir pim i Dispenser drawer D Door Lock Light Knobs are hidden To extract them gently Spin Speed O ON OFF Light press the middle of each knob Wash Temperature Introduction Congratulations on the purchase of your new Ariston washing machine It is a highly sophisticated engineered product that will give you many years of satisfaction Please read this
24. utions including the following A WARNING ELECTRICAL SHOCK HAZARD Plug washer dryer into a grounded 3 prong outlet Do not remove ground prong Do not use adapter Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock Read all instructions before using the appliance Do not wash articles that have been previously cleaned in washed in or spotted with gasoline dry cleaning solvents other flammable or explosive substances as they emit vapors that could ignite or explode Do not allow children to play on or in the appliance Close supervision of children is necessary when the appliance is used near children Before the appliance is removed from service or dis carded remove the door Do not reach into the appliance if the tub or drum is moving Do not install or store this appliance where it will be exposed to the weather Do not tamper with controls Do not repair or replace any part of the appliance or at tempt any servicing unless specifically recommended in the user maintenance instructions or in published user repair instructions that you understand or have the skills to carry out Do not add gasoline dry cleaning solvents or other flammable or explosive substances to the wash water These substances give off vapors that could ignite or explode A WARNING ELECTRICAL SHOCK HAZARD Disconnect power before servicing Replace all panels
25. ver small objects like coins hair clips keys etc may ac cidentally fall into the pump To avoid possible damage they are withheld in an accessible coin trap located at the bottom right corner of the washer If needed follow these instructions to remove items that may have accidentally been washed and got caught in the coin trap 1 With the washer OFF and empty gently ease down the top of the kick plate panel right with a flat blade screwdriver or plastic putty knife 2 Remove the panel by lifting slightly and pulling forward 3 Place a small pan or towel under the pump to catch any water still left in the pump 4 Turn the large knob counterclockwise and then pull the filter straight out 5 When finished cleaning reinstall the filter and ensure that it s securely tightened Finally re fit the kick plate panel Check the Rubber Inlet Hoses Yearly Inspect the inlet hoses yearly If you see any cracks bulges or other signs of wear replace the hose immedi ately Record the hose installation replacement dates on hoses for future reference IMPORTANT Always replace the inlet hoses after 5 years of use Maintenance and Care Winterization for RV or marine installs 1 2 3 4 5 A To winterize your washer dryer With machine power OFF pour 2 quart of RV type antifreeze into washer drum Close door Advance Program Dial to a Spin position Press ON OF
26. with the appliance If it will not fit the outlet have the proper out let installed by a qualified electrician WARNING Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded ARISTON A WARNING ELECTRICAL SHOCK HAZARD Plug washer dryer into a grounded 3 prong outlet Do not remove ground prong Do not use adapter Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock A 120 volt 60 Hz AC only 15 or 20 amp fused electrical supply is required Time delay fuse or circuit breaker is recommended It is recommended that a separate circuit serving only this appliance be provided This washer dryer is equipped with a 6 power supply cord having a 3 prong ground plug To minimize possible shock hazard the cord must be plugged into a properly grounded 3 prong electrical outlet capable of 120 Volt 60 Hz and grounded in ac cordance with local codes and ordinances If a mating outlet is not available it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed by a qualified electrician The outlet shouldn t be controlled by a wall switch or pull cord which can be turned off accidentally If codes permit and a separate ground wire is used
Download Pdf Manuals
Related Search