Airlink101 AWLL6090 Network Card User Manual
Contents
1. e Quick Installation Guide e Installation CD Driver Utility Manual 1 2 Features e Industry s highest wireless data rate of up to 300Mbps with IEEE 802 11n draft specification 2 0 e 64 bit 128 bit WEP encryption Pre shared Key PSK and Wi Fi Protected Access WPA2 and WPA support provide full protection for your wireless connection Higher data rate increases the reliability and stability of wireless connections Great for environments with higher wireless data traffic requirements Fully backward compatible with 802 11b g devices Works best with other AirLink101 Wireless 300N products 2 Installation This section provides instructions on how to install the Wireless 300N USB Adapter The driver is installed along with the utility Step 1 Insert the USB adapter into an available USB port on your computer Step 2 Windows will launch the Found New Hardware Wizard The Found New Hardware Wizard appears differently depending on your operating system Click Cancel to quit the wizard and insert the Installation CD into your CD drive Found Hew Hardware Wizard This wizard helps pon install oftware for Ethernet Controller If your hardware came with an installation CD QES or floppy disk insert it now What do you want the wizard to do Install the software automatically Recommended O Install from a list or specific location Advanced Click Next to continue Step 3 The Autorun screen will pop up Sel2. Version 1 00 00 0000 City Version Y1 00 MAC Address 00 18 02 4404 9C This Product is secured by Odyssey Copyright 2007 AirLink101 All Rights Reserved 36 Appendix A Features Frequency Band e 2 4 GHz Standards e IEEE 802 11b 802 119 e 802 11n draft 2 0 Interface e USB 2 0 Security e WPA PSK TKIP e WPA2 PSK AES Transmitted Power e 802 11b 17 dBm e 802 119 14 dBm e Draft 11n 14 dBm Data Rate e Transmitting Up to 300Mbps e Receiving Up to 300Mbps System Requirements e 150 MHz processor or better e 64MB RAM e Available USB port OS Compatibility e Windows 2000 XP Vista Dimensions e 77x27x14mm LxWxH Temperature e Operating 0 C to 40 C e Storage 20 C to 80 C Humidity e Operating 10 to 80 Non Condensing e Storage 5 to 90 Non Condensing Warranty e Limited 1 year warranty Safety Approvals e FCC CE IC Appendix B Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no gua
3. Length will also be predetermined by the router Refer to your routers settings to find out what you should select here Key Index is the key on the router that is currently in use Refer to your routers settings to find out what you should choose Once you are done click OK to save your settings 24 Configuring WPA WPA2 PSK Encryption for home users Profile Settings Basic Settings Profile Marne SSID Network TYPE GF Infrastructure f Adhoc Set security Option Pazsphrase Settings TKIP AES Key f 602 1 C None Show text in the password field select WPA WPA2 PSK from the Set Security Option box Under Passphrase Settings select either TKIP or AES depending on the settings for your router Enter the encryption key into the KEY box 25 Configuring WPA WPA2 Encryption for corporate networks Profile Settings Basic Settings Profile Mame SSID Metwork TYPE Infrastructure f Adhoc Set Security Option Advanced Security Settings f WEP TKIP C AES a E toma f BO21 f one select WPA WPA2 from the Set Security Option box Under Advanced Security Settings select either TKIP or AES depending on the settings for your router Click on Advanced Config to enter your authentication settings Advanced Security Settings EAP Type EAP TLS E4P TLS User Certificate LEAP E4P TTLS O Validate Server CexPEAP User Mame Th
4. Next to accept the default destination folder Airlink1O1 WLAN Monitor Install hield Wizard Choose Destination Location Select folder where setup will install files Setup will install Airlink 10T WLAN Monitor in the following folder To install to this folder click Next To install to a different folder click Browse and select another folder Destination Folder Cos Airlink TOT Airing TOT WLAN Monitor Browse InstallShield Airlink1O1 WLAN Monitor InstallShield Wizard Select Program Folder Please select a program folder Setup will add program icons to the Program Folder listed below fou may type a new folder name or select one from the existing folders list Click Nest to continue Back Nemo Lancel Step 6 Click Continue Anyway at the Windows Logo Screen For Windows 2000 click Yes at the Digital Signature Not Found prompt Software Installation A The software you are installing has not passed Windows Logo A testing to verity its compatibility with Windows AP Tellme why this testing i important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the software vendor for software that has passed Windows Logo testing Continue Anyway ff STOP For Windows Vista click the Install this driver s
5. box at the top of the window provides you with the status of the current connection including signal network name SSID IP Address and router channel FE AirLink101 Wireless Monitor Wireless Information Speed SDOhibps channel 5 Metw ork Mame getault signal all IP Address 192168 1100 4 H gt idetautt default Activate 18 4 2 AP List The AP List tab displays all the available wireless networks detected by the Wireless Adapter Simply select the wireless network you wish to connect to and click Connect lf you have created multiple profiles you can use the profile chooser at the bottom to select the specific profile you want to use Then click Activate to enable that profile PI AirLink101 Wireless Monitor Wireless Information Speed 300Mbps channel 5 Metwork Mame default signal all IP Address 192168 1100 19 4 3 Profile Settings This section provides instructions on using the Profile Settings section of the wireless monitor F AirLinki01 Wireless Monitor Wireless Information Channel 6 Network Name defaut Signal al IP Address 192 166 1101 My Wireless Mebworks Profile Details Network Mame default Network Type Infrastructure Security None EAS The My Wireless Networks box lists the different profiles you ve created for the different networks that you
6. software anyway Only install driver software obtained from your manufacturer s website or disc Unsigned software from other sources may harm your computer or steal Information l we 1 See details Step 11 Click Finish Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for ArLink 101 Wireless Adapter Click Finish to close the wizard 11 3 Configuring the Adapter This section describes how to connect your wireless adapter to a wireless network Note to Windows XP Users You must disable the Wireless Zero Configuration Utility in order to use the bundled Wireless Utility Please follow the steps below to disable XP s wireless utility Windows Vista users can skip the following instructions and go to Step 1 Double click on the Wireless Network Connection Icon in the system tray and then click on Properties or Advanced 1 Wireless Network Connection X Connected to Signal Strength Very Good NO 11 46 AM When the new wireless network connection properties window appears go to the Wireless Networks tab uncheck the Use Windows to configure my wireless network settings check box and click OK 12 Wireless Net ork Connection 12 Properties Ix General Wireless Networks me C Use Windows to configure my wireless network settings wallable networks To connect to an available network click C
7. 1 Wireless 300N USB Adapter Model AWLL6090 User s Manual Rev 1 0 Table of Contents INTO UCA dd diodo 3 1 Package Contento osa 3 12 CALLING S unitat cdi 3 A AN 4 JCO unng the Adapter sia ia 12 Ai WIFCIESS MONO isa AAA AAA 18 A WwWIreless IMMORIMAUON amarras 18 A A A tate ats 19 AS Prone Seting Sentado 20 AGAN MEE A o Deer oa 22 4 5 Ad hoc and Peer to Peer Wireless Networks oooccccoccconccccnccccncnconcncononononncnnanons 28 4 6 WIFI rOtected Setup WP Susanna 31 citados 36 APDENAIX A FS al Suecia 37 APpenabeB IO Ma lO Minsa 38 MECC E 40 1 Introduction Congratulations on your purchase of the Wireless 300N USB Adapter lts high bandwidth combined with extended wireless coverage delivers fast and reliable connection for all of your networking applications when used with Airlink1016 Wireless 300N Gigabit Router to achieve up to 300Mbps data rate A full range of security features such as WEP WPA PSK and WPA2 PSK provide the highest level of wireless network security The bundled Wireless Utility allows you to set up the adapter with an easy to use user interface Best of all the Wireless 300N USB Adapter works with 802 11g and 802 11b network devices ensuring compatibility with your existing wireless products 1 1 Package Contents Before you begin the installation please check the items of your package The package should include the following items e Wireless 300N USB Adapter e USB Cable
8. e adapter supports EAP TLS LEAP EAP TTLS and PEAP authentication methods Refer to your system administrator for information about what settings you should enter here 26 Configuring 802 1x authentication for corporate networks Profile Settings Basic Settings Profile Mame SSID Network Type Infrastructure 0 Adhoc Sel Security Option lt Advanced Security Settings O WEF OOAPAMP AZ PSK Mone Select 802 1x from the Set Security Option box Click on Advanced Config to enter your authentication settings Advanced Security Settings ESP Type EAP TLS Tr EAP TLS User Certificate LEAP EAP TTLS Validate Server CeyPEAP User Mame Pas ord Contirm Pas word 21 The adapter supports EAP TLS LEAP EAP TTLS and PEAP authentication methods Refer to your system administrator for information about what settings you should enter here 4 5 Ad hoc and Peer to Peer Wireless Networks Ad hoc networking is used when you want to connect two or more computers together but you don t have a router In ad hoc mode you lose a lot of the features that come with a router The maximum connection speed drops significantly to 11Mbps WEP encryption is the only security available in ad hoc mode To set up ad hoc mode you will need to create a new profile F y AirLink101 Wireless Monitor Wireless Information Channel 6 Network Name celtas Signal all IP Address 19216851 101 Profile Setti
9. e connected Step 4d Click Continue on the router configuration screen WPS The Result of Adding Wireless Device WPS Success You have added the wireless device to your wireless network successfully please click on the button below to continue 34 Step 5 Click Finish on the WPS Connection screen A y WPS Connection E WiFi Protected Setup WiFi Protected Setup process done Utility reconnect to your wireless network with security Please click Finish Note If you cannot connect successfully with WPS you need to log in to your router s configuration and click on Wireless Then click Wireless security Make sure that the Wi Fi Protected Setup Enable box is checked An LINK Access Application amp Setup Wireless Security Restrictions Gaming Administration Status J00N Wireless Router Basic Wireless Settings Wireless Security Wireless MAC Filter Advanced Wireless Settings Wireless Network Wireless Settings Security Mode Disabled wt Wi Fi Protected Setup Enable Current PIM 05202463 Generate Mewe PIN Reset PIN to Detault Wi Fi Protected Status Enabled Mot Configured Reset to Unconfigured Add wireless Device Wizard 35 4 7 About The About tab shows the Utility Driver versions and the MAC address of the adapter A 4 AirLink101 Wireless Monitor Wireless Information Channel E Metwork Name defaut Signal al P Address 192 166 1102 on a a Wireless Mionitor IRLIN Driver
10. ease enter the following PIN number into your access point and click Mest 00750922 33 Step 4b Log in to your router s configuration page from the web browser and click on Wireless Then click Wireless security Make sure that the Wi Fi Protected Setup Enable box is checked Click the Add Wireless Device Wizard button A R LINK ime ee Setup Wireless Security Restrictions Application amp Gaming Administration Status 300N Wireless Router Basic Wireless Settings Wireless Security Wireless MAC Filter Advanced Wireless Settings Wireless Network security Mode Disabled hal Wireless Settings Wi Fi Protected Setup Enable Current FIM 05202483 Wi Fi Protected Status Enabled Mot Configured Step 4c Enter the Pin Code in the Pin Number box and click Connect Draft 3027 11N Wireless Router Wi Fi Protected Setup There are two way to add a wireless device to your wireless network PIN or Push Button lf the wireless device you want to add only comes wih a PIN number enter ts PIM number below and press the Connect button t vill help you to add this device to your wireless network If the wireless device your want to add has both options available you may use the virtual Push Button if you prefer Push Button Virtual Push Button After a few moments both the router configuration screen and the adapter configuration screen should show a message telling you that you ar
11. ect Install Utility and Driver from the menu Repeat Abintiys Wireless 300N USB Adapter Install Utility and Driver View User Manual View Quick Installation Guide Install Adobe Acrobat Browse CD Exit Note If the Autorun screen doesn t appear automatically or if you get a blank white screen or a white screen shows up your computer doesn t have Adobe Flash Player installed go to Start Run and type D Utility Setup exe where D is the letter of your CD drive and click OK Windows Vista users At this point you may get a warning message like the one below Make sure that you click Allow to continue with the installation User Account Control Po An unidentified program wants access to your computer User Account Control stops unauthorized changes to your computer The source and purpose of this program are unknown Don t run the program unless you have used it before or know where it s from FE Unidentified Publisher Cancel I don t know where this program is from or what it s for gt Allow I trust this program because I ve used it before or know where it s from Details Step 4 Click Next at the welcome screen Airlink101 WLAN Monitor InstallShield Wizard Welcome to the InstallShield Wizard for Airlink O1 WLAN Monitor The InstallShield Wizard will install Airlink 101 WLAN Monitor on our computer To continue click Next Back Cancel Step 5 Click
12. ions and environmental factors including volume of network traffic building materials and construction mix of wireless products used radio frequency interference e g cordless telephones and microwaves as well as network overhead lower actual data throughput rate Specifications are subject to change without notice All products and trademarks are the property of their respective owners Copyright 2008 AirLink101 40
13. less Monitor Wireless Information Speed 300Mbps channel 5 Network Mame detant signal all IP Address 499416814100 Connected Ss0 macessiD 8 Secu Chan gt default 00 0C 43 28 b 00 dos Wireless p ives come AS 7 i defaut default X Activate gt 31 Step 2 Choose your configuration method either Push Button or Pin Code and click Next F y WPS Connection Eg WiFi Protected Setup WiFi Protected Setup Welcome to Sirink107 Wireless Connection Wizard following the steps will guide you to connect to your wireless network our Ailink101 wireless adapter supports WiFi Protected Setup FS which allows pou to connect to a wireless network easily This feature can be only used with a wireless network that supports WPS Push Button O Pin Code Step 3a If you choose the Push Button method make sure that you click on the Wi Fi Protected Setup button A 4 WPS Connection WiFi Protected Setup WiFi Protected Setup Push button function ls easily to connect to pour wireless network Please ensure pour access point is nearby and Click PRESS button Wi Fi PROTECTED SETUP 32 Step 3b Push the WPS button on the router and the blue LED will start blinking The router will now start the handshake with the wireless adapter then the connection will be built up in couple minutes x WiFi Protected Setup PIN from wireless adapter Pl
14. llow operation instruction as documented in this manual This transmitter must not be co located or operating in conjunction with any other antenna or transmitter SAR compliance has been established in typical laptop computer s with USB slot and product could be used in typical laptop computer with USB slot Other application like handheld PC or similar device has not been verified and may not compliance with related RF exposure rule and such use shall be prohibited 38 Industry Canada Statement This device complies with RSS 210 of the Industry Canada Rules Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device IMPORTANT NOTE IC Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment End users must follow the specific operating instructions for satisfying RF exposure compliance To maintain compliance with IC RF exposure compliance requirements please follow operation instruction as documented in this manual 39 Technical Support E mail support airlink101 com Toll Free 1 888 746 3238 Web Site www airlink101 com Theoretical maximum wireless signal rate derived from IEEE 802 11g standard and IEEE 802 11n draft specification version 2 0 Actual data throughput will vary Network condit
15. nected You should see Connected in the top right hand corner and there will be a blue circle around the antenna icon next to the network name FE AirLink101 Wireless Monitor Wireless Information speed 300Mbps Channel E Metyvyvork Mame default signal all IP Address 392 168 1100 00 0C 43 28 b 00 dos lt i gt defaut default Activate Troubleshooting If you are experiencing problems with the connection unable to connect low signal strength slow connection speed not working unstable wireless connection you will want to tune your router s signal by changing channels on the router You do not need to change the channel on the card it will automatically pick up the new channel after you reboot The only channel that you need to change is the router s channel Your router has 11 different channels to choose from Start with channel 1 and work your way up Each time you change the channel on the router make sure that you 16 restart the wireless computer before trying to connect again Keep going through the channels until you find one that gives you a stable connection For instructions on changing channels refer to the documentation that came with your router 17 4 Wireless Monitor This section describes the various functions of the Wireless Monitor that you can configure including the settings of wireless encryption 4 1 Wireless Information The Wireless Information
16. ng Profile Details Network Mame Network Type Security 28 Open the Wireless Monitor Click on Profile Setting then click on New The profile settings box will appear Profile Settings Basic Settings Profile Mame SSID Network Type Infrastructure f Adhoc Channel E Set Security Option Mo Security First change the network type to Adhoc Infrastructure is for when you are using a router Enter a profile name into the Profile Name box so that you can identify the profile Type in a network name SSID into the SSID box Select your desired Channel You can also choose between no security or WEP security If you choose WEP security you can follow the instructions in the Configuring Encryption section of the manual Click OK to save the profile 29 Once that is done click on the AP List PI AirLink101 Wireless Monitor Wireless Information speed SDOhibps Channel 5 Network Mame default Signal all IP Address 499416814100 Connected SSID____ MAC BSSID _ S _ Secu Chan r default 00 00 43 28 6 88 Wireless lt i gt detautt default T Activate Select your new profile from the profile chooser and click Activate to enable the profile You will need to configure all other computers that you are planning on connecting to your ad hoc network with the same settings that you input on this screen Every computer has to be set up exactly the same If an
17. oftware anyway button when the security warning appears x Windows Security K Windows can t verify the publisher of this driver software F Don t install this driver software You should check your manufacturers website for updated driver software for your device Install this driver software anyway Only install driver software obtained from your manufacturer s website or disc Unsigned software from other sources may harm your computer or steal information l Ww See details Step 7 Click Yes want to restart my computer now and then Finish to restart your computer Airlink101 WLAN Monitor InstallShield Wizard InstallShield Wizard Complete The InstallShield Wizard has successtully installed Airlink 101 WLAN Monitor Before you can use the program you must restart pour computer No will restart my computer later Remove any disks from their drives and then click Finish to complete setup Cancel Step 8 After the computer is restarted Windows will ask to connect to Windows Update select No not this time and click Next If this screen does not appear you can skip to section 2 2 Found New Hardware Wizard Welcome to the Found New Hardware Wizard Windows will search for current and updated software by looking on your computer on the hardware installation CD or on the Windows Update eb site with your permission Read our privacy policy Can Windows connect to Windows Upda
18. onfigure wireless A Configure 4 1084F 3 a z Preferred networks i TA N a A LS AS ees a AS Automatically connect to available networks in the order listed below Move up Move down Add Remowe Properties Learn about setting up wireless network configuration Advanced Step 1 To open the utility double click on the Wireless Monitor icon in the system tray at the bottom right hand corner of your screen 4 27 PM Step 2 Go to the AP List tab select the SSID Network Name of the wireless network you wish to connect to and click Connect 13 PE AirLink101 Wireless Monitor Vireless Information speed 300Mbps Channel 65 Network Mame default signal all IP Address 3192168 1100 Connected Wireless i detant default Activate If the network you are attempting to connect to is configured for encryption you will see an orange lock icon next to the network 14 fi AirLink101 Wireless Monitor Wireless Information speed 300Mbps Channel 5 Network Mame default Signal all IP Address 192168 1100 Connected cu 88 ry lt i gt defaut default Activate When you click on it and click connect a box will pop up requesting the wireless encryption key for the router Enter the encryption key into the box and click OK Connection This network requires a network key OEP Key Show text in the password field 15 Step 3 You should now be con
19. ose from 22 Profile Settings Basic Settings Profile Mame E SSID defautt Network Type f Infrastructure f Adhoc Set security Option Mo Security WEP CW PAANP AS PS CAPA PAZ C 602 1 e None These three are meant for the home user None No encryption in use WEP The most popular but least secure form of encryption WPA WPA2 PSK The most secure and recommended level of encryption The remaining two are for use in a corporate environment that utilizes authentication servers If you do not know if you have an authentication server you probably don t and will want to stick with the three options above 23 Configuring WEP encryption Profile Settings Basic Settings Profile Marne SSID f Adhoc Set security Option Wired Equivalent Privacy MEF le WEF f Open C Shared Auto CAPA PA2 PSK Key Key Length Key Index C 802 1 164 bits 40 241 10 Hexadeci i C None CAPA PAZ Show text in the password field select WEP from the Set Security Option box Under Wired Equivalent Privacy WEP you will want to select Shared or Open depending on the router settings In the Key box you will want to type in the encryption key for the router If you check the Show text in the password field box your key will appear in the box as you are typing it instead of showing only asterisks This is helpful as it allows you to double check the key before saving the changes Key
20. rantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment IEEE 802 11b or 802 11g operation of this product in the U S A is firmware limited to channels 1 through 11 IMPORTANT NOTE FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment End users must follow the specific operating instructions for satisfying RF exposure compliance To maintain compliance with FCC RF exposure compliance requirements please fo
21. te to search for software O Yes this time only Click Next to continue Step 9 Select Install the software automatically and click Next Found New Hardware Wizard This wizard helps you install software for Aurlink 101 Es If your hardware came with an installation CD a 22 or floppy disk insert it now what do pon want the wizard to do O Instal from a list or specific location Advanced Click Next to continue Step 10 Click Continue Anyway at the Windows Logo Screen For Windows 2000 click Yes at the Digital Signature Not Found prompt Software Installation A The software you are installing has not passed Windows Logo testing to very its compatibility with Windows lt P Tell me why this testing ls important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the software vendor for software that has passed Windows Logo testing Continue Anyway STOP Installation 10 For Windows Vista click the Install this driver software anyway button when the security warning appears x Windows Security Windows can t verify the publisher of this driver software gt Don t install this driver software You should check your manufacturer s website for updated driver software for your device Install this driver
22. use Profiles are automatically created and added to this list when you connect to new networks You can also manually add profiles To modify an existing profile select that profile from the My Wireless Networks box and click on modify To create a new profile click on New 20 The Profile Settings box will appear allowing you to specify the settings for your new profile or change settings for your existing profile Profile Settings Basic Settings Profile Mame CEA SSID Ci Network Type e Infrastructure C Adhoc Set Security Option Mo Security O EP WPAN PA2PSK D PAAPA 802 1 f one Once you are finished entering the settings click OK to save the changes 21 4 4 Configuring Encryption This section describes the different types of encryption available and how to configure them In most cases encryption will be automatically configured and all that will need to be entered is the key as described in Section 3 Step 2 The only time you will need to manually configure the encryption settings is if you are creating a custom profile Click on Profile Settings then New A 4 AirLink101 Wireless Monitor Wireless Information Channel 6 Network Name Getaull Signal all IP Address 192 166 1101 Profile Setting Profile Details Metwork Name Security The profile settings box will appear This is where you will change your encryption settings As you can see you have five different options to cho
23. y of the settings are different the network will not function Troubleshooting If you are having trouble connecting if the connection is slow or if it is unstable you will want to try changing channels Start with channel 1 and work your way up until you find a channel that gives you a stable connection Each time you change the channel save the settings then reboot the computer Also make sure that you do this on every ad hoc machine so that they will all be set to the same channel 30 4 6 Wi Fi Protected Setup WPS Wi Fi Protected Setup M WPS is a new and easy way to configure the encryption for your wireless network clients In order to use it with your router firstly you will need to have a router that supports this feature like the AR690W Alrlink101 Wireless 300N Gigabit Router Secondly you must configure the wireless encryption on the router you can find instructions for configuring it in the User Manual located on the CD that came with your router If your wireless router does not support WPS you will need to set up the wireless security manually and you can skip this section In the instructions below we are going to use the utility Wireless Monitor that comes with the Airlink101 Wireless 300N adapters and the AR690W Alirlink101 Wireless 300N Router as the example Step 1 Go to the computer with the Wireless 300N adapter and open the Airlink101 Wireless Monitor Click on the WPS Connect button Pat AirLink101 Wire
Download Pdf Manuals
Related Search