3M M150 Computer Monitor User Manual
Contents
1. sess ennt enne 5 Intended U 86e teer e tdi nuire neta dida iret e oe RE eatd 5 Explanation of Symbols x nei ette et e erit m Peter dn 6 Service and Repair Indicators eese eene 7 3M Touch Systems Support Services esses 7 3M Touch Systems Worldwide Offices esssssssseeeeeeeeenn 8 Introduction to Flat Panel Displays Capacitive and Resistive Options ener ener nnns 10 Native Video Resolution on a Flat Panel Display esee 10 Options for Using Other Video Resolutions sssseeeene 10 Setting Up Your M150 FPD Monitor System Requirements ec nct tee rg e n ee eo edge edd 11 Unpacking Your Touch Monitor ccccccccsccesscssceesceeseeeeeeeeceeessecesecnseeeseeseeeseeeens 12 Atm Mounting Option 5 2 e teta Ode reete a eee tuiles edet teen 12 Countertop Base Mounting Option ssssssssseseeeee ener 13 Access to the Video Controls sess eene ener rnnt 14 Adjusting the Viewing Angl sioc enra a nennen RR 14 Installing the Video Card and Video Driver sse 15 Supported Video Display Modes and Refresh Rates 15 Configuring the Display Settings sse 15 Using the Standard Controls for the Video Card sss 16 Multimedia Features eee better tiet erre o Le Re Pe rte leet 16 Optional Card Reader Bracket cccccccccsscesscesseeeeeeeeeesseeeseeeseecsaecaecnaeense2. Cable Management System Figure 9 Removing the Cable Management Cover Once you have connected your M150 FPD monitor to your computer you should take advantage of the cable management system designed into the base of the M150 FPD monitor as shown above In order to properly route all cables through the cable management system the cover on the base unit must be removed To remove this cover 1 Push in and lift up on each of the two tabs located on the left and right sides of the cover This action will release the cover tabs from the base 2 Slide the cover back towards you to remove 3M Touch Systems Proprietary Information 20 M150 FPD Monitor Installation Guide Testing the M150 FPD Note The M150 FPD has a power status light located on the front of the bezel After connection turn on the power switch located at the bottom of the front bezel Before you test your touch monitor make sure all cables are connected properly and routed through the cable management system Be sure to tighten all cable screws To test that the monitor is working properly Turn on your computer 2 Make sure the video image is displayed If it is not turn on your monitor 3 Make sure the video image is centered within the screen area Use the monitor controls to adjust the image if necessary E Power switch Volume Microphone i Head Phones
3. Perform an Auto Config first then if you wish you can adjust the horizontal and vertical position contrast and brightness to better suit your video card and your personal preference Refer to Chapter 3 for more information on using the on screen menu to adjust the video display Installing TouchWare Software TouchWare software includes the touch screen driver and control panel that enables your touch screen to work with your computer When you install the CD included with your monitor TouchWare will automatically load the correct driver for your system 3M Touch Systems currently supports touch screen drivers for the following PC operating systems e Windows XP serial and USB e Windows 2000 serial and USB e Windows NT 4 0 serial only e Windows 9x serial and USB Windows 98 only e Windows Me serial and USB These drivers and relevant technical documentation can be found on the latest 3M Touch Solutions CD 19 640 and are also available for download from our website at www 3Mtouch com After the software is installed restart your computer to load and activate the touch screen driver To complete the setup of your touch monitor make sure you calibrate the touch screen 3M Touch Systems Proprietary Information Chapter 2 Setting Up Your M150 FPD Monitor 21 Calibrating the Touch Screen After you connect your touch monitor and install TouchWare software you must calibrate the touch screen Calibration serves tw
4. simple as touching the screen This guide describes how to set up your M150 Flat Panel Display FPD touch monitor This document assumes you have basic computer skills You should know how to use the mouse and keyboard choose commands from menus open and run application programs and save files Important Safety Information Read and understand all safety information before using this product Follow all instructions marked on the product and described in this document Pay close attention to the following installation warnings and safety precautions Intended Use The M150 flat panel display FPD touch monitor was designed for touch input and tested to replace an existing monitor These monitors are intended for indoor use only and are not designed for use in hazardous locations A DANGER To avoid the risk of fire and or explosion which will result in serious injury or death Do not install or use this product in a hazardous location WARNING To avoid the risk of fire which could result in serious injury or death Do not remove the cover or back of the monitor To avoid the risk of electric shock which could result in serious injury or death e This device must be operated with the original power supply part number HJC HASUOSF or CHI CH 1234 Do not use a damaged power supply Do not use a power cord that is frayed or otherwise damaged 3M Touch Systems Proprietary Inform
5. 1 4 turn horizontal to vertical to loosen Adjust the M150 FPD by pushing on the top front of the monitor until the screen is at the best viewing angle for you Then turn the adjustment knob a 1 4 turn back to lock in place To raise the monitor back to vertical unlock the adjustment knob lift slightly on the adjustment knob and pull up Figure 4 Viewing Angle Adjustable from 0 up to 60 degrees T DN 3M Touch Systems Proprietary Information Chapter 2 Setting Up Your M150 FPD Monitor 15 Note When the adjustment knob is horizontal it is locked when it is in the vertical position it is unlocked Always maintain adequate ventilation to protect the display from overheating and to ensure reliable and continued operation Installing the Video Card and Video Driver Before you can connect your touch monitor make sure your computer has a video card and driver already installed for the monitor The video driver is supplied by the video card manufacturer and may be found on the disks that came with your computer If you need information on installing a video card or video driver refer to your computer documentation for instructions Supported Video Display Modes and Refresh Rates Your video card should support one of the display modes specified in Table 1 If you select an unsupported video mode the monitor may stop working or display unsatisfactory picture quality Table 1 Applicable Display Mode and Refresh Ra
6. 12 2180204 IDT 3321 02 IDT 3331 23 2180205 IDT 3321 02PP IDT 3331 33 2180206 IDT 3321 12 IDT3301 02 21040103 IDT 3321 12PP IDT3301 12 21040104 IDT 3321 23 IDT3301 23 IDT 3321 23PP IDT3301 33 Figure 6 Card Reader Mounting and Cable Management Connecting the Touch Monitor A CAUTION You are cautioned that any change or modification to the equipment not expressly approved by the party responsible for compliance could void your authority to operate such equipment To connect the M150 FPD monitor 1 Turn off your computer You should always turn off the computer before connecting or disconnecting any device 2 Connect one end of the video cable to the video connector on the FPD Connect the other end to the video card in your computer 3 Connect one end of the touch screen cable either serial or USB to the FPD Connect the other end to an available port on the back of your computer If you are using a USB connection make sure you have installed the TouchWare drivers prior to connecting the touch screen cable 3M Touch Systems Proprietary Information 18 M150 FPD Monitor Installation Guide 4 Plug the AC DC power supply into the M150 FPD Be sure to use the power supply included with the monitor Figure 7 Identifying Your Monitor Connections Touch Screen Microphone out Line In Video Connection A WARNING To
7. Repair Indicators Do not attempt to service this unit yourself Removing the display cover may expose you to dangerous voltage or other risks and will void the warranty WARNING To avoid the risk of fire which could result in serious injury or death e Do not remove the cover or back of the monitor A CAUTION To avoid the risk of electric shock which may result in minor or moderate injury e Do not service the monitor e There are no user serviceable parts inside e Refer all servicing to qualified service personnel e Do not remove the cover or back of the monitor Unplug the display from the power outlet and refer servicing to qualified service personnel in the event that e Liquid is spilled into the product or the product is exposed to rain or water e The product does not operate properly when operating instructions are followed e The product has been dropped or the case has been damaged e The product shows a distinct change in performance indicating a need for service e The power cable or plug is damaged or frayed 3M Touch Systems Support Services 3M Touch Systems provides extensive support services through our website and technical support organization Visit the 3M Touch Systems website at http www 3mtouch con where you can download touch screen software and drivers obtain regularly updated technical documentation on 3M Touch Systems products and learn more about our company When
8. force 3M Touch Systems Proprietary Information CHAPTER 2 Setting Up Your M150 FPD Monitor This chapter describes how to set up and integrate your 3M Touch Systems M150 FPD monitor into a touch application You need to complete the following tasks e Unpack the components e Connect the video touch screen and power cables e Power on the monitor and test your setup e Install the touch screen software e Calibrate the touch screen System Requirements The M150 flat panel touch monitor requires a personal computer PC This touch monitor will not work with Apple Macintosh computers The requirements for your PC are as follows e Your PC must have an available RS 232 serial communication COM port or USB port You connect the touch screen to this port e Your PC must have a video card and video driver already installed for the monitor If you need to install a video card or a video driver refer to your computer documentation for instructions e Your PC must have a unique interrupt request IRQ available to the touch screen COM port The touch screen cannot share an IRQ with another device e Ifthe only serial port available on your PC has 25 pins you will need a 9 pin to 25 pin adapter When choosing your workspace select a sturdy level surface Also make sure you can easily access the back of the touch monitor and the computer Easy access helps ensure a smooth setup of the touch monitor Note Before setting up
9. in your computer e Check that the video input from the video card falls within the refresh rate of the display Refer to Table 1 for details e Check that your computer is using a supported display mode Refer to Table 1 for details Is the monitor in Power Management mode e Touch the screen press any key on the keyboard or move the mouse to restore operation Are the brightness and contrast settings too low e Usethe monitor controls to adjust these values Abnormal image e Check that the video input from the video card falls within the refresh rate of the display Refer to Table 1 for details e Check that the video cable is connected properly and securely to the monitor and the computer Colors of image e Check that the video cable is connected properly and securely to the monitor and the are abnormal computer e Check that no pins are bent in the video cable connector Disturbances on the screen e The video display adjustments are incorrect Refer to Chapter 3 for adjusting procedures 3M Touch Systems Proprietary Information Chapter 4 Maintenance and Troubleshooting 31 Troubleshooting the Touch Screen If you are experiencing problems with the touch screen check the following list of common installation errors Table 2 Common Touch Screen Installation Issues Common Installation Issues Touch screen does not respond to touch Possible Solutions Review the installation procedures Are all cab
10. left and gt right arrow buttons to scroll through the position menu e H Position is used to adjust the horizontal image position manually e V Position is used to adjust the vertical image position manually Image Use the lt left and P right arrow buttons to scroll through the image menu Phase If the phase of your monitor is not fine tuned you may observe unstable horizontal noise lines and cross talk stretching from the edge of small windows on your display If you change your display to Windows shut down mode this noise will be more visible and easier to eliminate Click on the Start button at the bottom right side and then click Shut Down This will bring you to the Windows shutdown mode After finishing phase adjustment click on the Cancel to return to your original Windows display Clock If the clock setting of your image is not fine tuned you may observe periodic vertical bars of video noise on your image These bars of noise are usually adjusted out when an Auto Configuration is performed If the bars of noise are still present this setting can be adjusted manually Adjust this setting so that either the vertical bars of noise are replaced by an even amount of noise across the whole screen or the noise disappears completely If you do an Auto Config the monitor will try to find the best Clock Phase setting If you are not satisfied with the auto adjustment fine tune the phase manually as described abov
11. to the problems you are experiencing with the monitor You may also want to consult your video card user s manual for additional troubleshooting advice Maintaining Your Touch Monitor To maintain your display and keep your monitor operating at peak performance e Keep your monitor and screen clean e Adjust the monitor video controls Refer to Chapter 3 for more information e Do not install the display in a place where ventilation may be hindered Always maintain adequate ventilation to protect the display from overheating and to ensure reliable and continued operation Touch Screen Care and Cleaning The touch screen requires very little maintenance 3M Touch Systems recommends that you periodically clean the glass touch screen surface Typically an isopropyl alcohol and water solution ratio of 50 50 is the best cleaning agent for your touch screen You can also use straight isopropyl alcohol In addition 3M Screen and Keyboard Cleaner CL680 has been tested and approved for this use A CAUTION To avoid the potentially hazardous situations associated with the use of alcohol or other solvents which may result in minor or moderate injury or property damage e Follow all instructions and recommendations in the manufacturer s Material Safety Data Sheet and product label e Be sure to follow solvent manufacturer s precautions and directions for use when using any solvents e tis important to avoid using any caustic chemicals on the
12. touch screen Do not use any vinegar based solutions 3M Touch Systems Proprietary Information 30 M150 FPD Monitor Installation Guide Apply the cleaner with a soft lint free cloth Avoid using gritty cloths Always dampen the cloth and then clean the screen Be sure to spray the cleaning liquid onto the cloth not the screen so that drips do not seep inside the display or stain the bezel Always handle the touch screen with care Do not pull on or stress cables Monitor Installation Problems Problem No image displayed blank screen Possible Causes and Solutions Is the monitor receiving power e Check that the computer s power cable is connected properly and securely in a grounded electrical outlet e Check that the AC DC power supply is firmly plugged into the monitor e Check that the green light appears on the bezel indicating the monitor is powered on e Check that the AC DC power supply cable is connected properly and securely to an electrical outlet Check that the LED 1s showing green on the AC DC power supply e Try using another power cable e Try using another electrical outlet Is the monitor receiving a valid video signal from the PC e Check that the computer is powered on e Check that the video cable is connected properly and securely to the monitor and the computer e Check that no pins are bent in the video cable connector e Check that the video card is firmly seated in the card slot
13. M150 Flat Panel Display Touch Monitor User Guide 3M Touch Systems Read and understand all safety information contained in this document before using this product 3M Touch Systems Proprietary Information 2 M150 FPD Monitor Installation Guide The information in this document is subject to change without notice No part of this document may be reproduced or transmitted in any form or by any means electronic or mechanical for any purpose without the express written permission of 3M Touch Systems 3M may have patents or pending patent applications trademarks copyrights or other intellectual property rights covering subject matter in this document The furnishing of this document does not give you license to these patents trademarks copyrights or other intellectual property except as expressly provided in any written license agreement from 3M Touch Systems The information provided in this document is intended as a guide only For the latest detailed engineering specifications please contact your 3M Touch Systems Application Engineer 3M Touch Systems is committed to continually improving product designs as a result product specifications may be subject to change without notification NOTICE Given the variety of factors that can affect the use and performance of a 3M Touch Systems Product the Product including that solid state equipment has operation characteristics different from electromechanical equipment some of which factor
14. and countertop applications with built in multimedia options Yoke Adjustment Knob The newly redesigned M150 monitor features an innovative design adjustable to approximately 60 off the vertical to accommodate different counter and user heights a positive locking mechanism a weighted base for additional stability a touch screen interface several mounting options and built in cable management The M150 monitor also features a space saving design high resolution low radiation and low power consumption These qualities make the M150 FPD touch monitor ideal for applications that require superior color resolution and clarity The M150 FPD is available in a 15 diagonal screen size using active matrix thin film transistor AM TFT liquid crystal display technology The M150 monitor supports a full screen resolution of 1024 x 768 Note The M150 FPD has a power LED as well as four buttons for using the on screen menu and adjusting the video display Refer to Chapter 3 for more information on these controls 3M Touch Systems Proprietary Information 10 M150 FPD Monitor Installation Guide Capacitive and Resistive Options The monitor is available with 3M Touch System s ClearTek capacitive touch screen Capacitive is the touch screen of choice for public access applications requiring high levels of durability and reliable performance 24 hours a day 7 days a week For those applications that re
15. ation M150 FPD Monitor Installation Guide A CAUTION To avoid the risk of electric shock which may result in minor or moderate injury The socket outlet should be installed near the equipment and should be easily accessible Use a power cable that is properly grounded Always use the appropriate AC cord certified for the individual country Some examples are listed below USA UL Switzerland SEV Canada CSA Britain BASE BS Germany VDE Japan Electric Appliance Control Act Do not service the Flat Panel Display There are no user serviceable parts inside Refer all servicing to qualified service personnel The backlight inverter output is at high voltage Do not use non conforming replacement parts Do not place wet or damp objects on the monitor Do not expose the monitor to rain or other sources of water steam or moisture Do not place foreign objects on the monitor or its cables Do not remove the cover or back of the monitor To avoid the risk of glass breakage which may result in minor or moderate injury Handle the monitor with care to avoid breaking the touch screen sensor The display contains glass parts Dropping the display may cause the glass parts to break Do not place foreign objects on the monitor To avoid the potentially hazardous situations associated with the use of isopropyl alcohol which may result in minor or moderate injury or property damage Follow all instructions and recommendation
16. avoid the risk of electric shock which could result in serious injury or death This device must be operated with the original power supply part number HJC HASUOSF or CHI CH 1234 A CAUTION To avoid the risk of electric shock which may result in minor or moderate injury The socket outlet should be installed near the equipment and should be easily accessible Use a power cable that is properly grounded Always use the appropriate AC cord certified for the individual country Some examples are listed below USA UL Switzerland SEV Canada CSA Britain BASE BS Germany VDE Japan Electric Appliance Control Act 5 Connect the power cable to the AC DC supply Connect the other end to the appropriate AC outlet Figure 8 Connecting the M150 Cables to your Computer You should be sure all cable connections are secure tighten all cable screws Shaking and vibration may dislodge cables that are improperly connected 3M Touch Systems Proprietary Information Chapter 2 Setting Up Your M150 FPD Monitor 19 Route all wiring and cabling away from heat sources and sharp metal edges to avoid damage Also keep the touch screen cable away from sources of electromagnetic and radio frequency interference A WARNING To avoid the risk of electric shock which could result in serious injury or death e Do not use a damaged power supply e Do not use a power cord that is frayed or otherwise damaged
17. e 3M Touch Systems Proprietary Information Chapter 3 Video Display Options 27 Miscellaneous Menu own He B MISC MENU RESET OSD POSITION SYSTEM INFO The Miscellaneous Menu contains three options Reset OSD Position and System info e Reset is used to reload all factory default parameters e OSD position is used to setup the OSD menu position horizontal and vertical position is adjusted separately Each position item will bring up the slider window the maximum value of the sliders are based on the size of the OSD menu e System Info is used to provide detailed information regarding the current input resolution frequencies and firmware version Note The OSD will timeout after 45 seconds of inactivity and will not save any new settings Lock Out Feature Once you have fine tuned your display you may want to restrict users from inadvertently making changes In order to do this follow this simple procedure Repeat the procedure to restore access 1 Press SELECT and then press the lt left arrow key Hold both keys for 10 seconds DO NOT RELEASE 2 Then press the right arrow key and hold all three keys together for an additional 10 seconds 3M Touch Systems Proprietary Information CHAPTER 4 Maintenance and Troubleshooting If you have a problem setting up or using your monitor you may be able to solve it yourself Before calling 3M Touch Systems try the suggested actions that are appropriate
18. eneeeeseenaes 16 Connecting the Touch Monitor sse eee 17 Cable Management System sess ener nnne nnne 19 Testing the MTSO EPD i tee et dp ser ER Sob Gee erri laces ete Pee det uds 20 Installing TouchWare Software esses ener enne 20 Calibrating the Touch Screen sess 21 3M Touch Systems Proprietary Information 4 M150 FPD Monitor Installation Guide Chapter 3 Video Display Options Adjusting the M150 Video Display essen 23 AWO Config statute ete rte n t C o Te Ede e 24 Brieghtness a2 oie RR SHE ERR HERR RERUES 24 OaE r E E 25 COLOR A E EE A ES 25 ILIE OT E E eei tetti E EEE 25 lun 26 Miscellaneous Mein 3 1 trece eR PR T ERE IRE a A aR 27 Lock Out Feature c iro er erected emen e DR Haero 27 Chapter 4 Maintenance and Troubleshooting Maintaining Your Touch Monitor essere ener 29 Touch Screen Care and Cleaning sess 29 Monitor Installation Problems esses ener 30 Troubleshooting the Touch Screen sse ener 31 Power Managemint 5 iere Trete ctt bee petenti eite e eee a a acad 31 M150 Regulatory Agency Approvals sse ener 31 ECC Warning uite eet testo A EETA 32 CE Conformity for Europe esssssssesseeeseeeeee eren ener enne 32 3M Touch Systems Proprietary Information Overview Welcome to the world of 3M Touch Systems a world where using a computer is as
19. ever you contact Technical Support please provide the following information Part number and serial number from your monitor Current driver version Operating system used Information on additional peripherals Technical Support is available Monday through Friday 8 a m to 8 p m US Eastern Standard Time 9 a m to 5 p m throughout Europe Limited call back service Saturdays and Sundays You can contact 3M Touch Systems Technical Support US only Eastern Standard Time by calling the hot line sending an email or sending a fax 3M Touch Systems Proprietary Information 8 M150 FPD Monitor Installation Guide Technical Support Hot Line 978 659 9200 Technical Support Fax 978 659 9400 Toll Free 1 866 407 6666 Email US TS techsupport mmm com 3M Touch Systems Worldwide Offices All offices can be reached through the website http www 3mtouch conm e United States 978 659 9000 e United Kingdom 44 0 1235 444400 e Australia 61 3 9582 4799 e Canada 604 521 3962 e France 33 1 30 31 68 32 e Germany 49 0 2131 14 4003 e Hong Kong China 852 2333 6138 e taly 39 0 39 230 2230 e Japan 81 44 811 1133 e Korea 822 552 3198 e Singapore 765 6450 8851 e Spain 34 934 15 6285 e Taiwan 886 2 2704 9011 3M Touch Systems Proprietary Information CHAPTER 1 Introduction to Flat Panel Displays The 3M Touch Systems product line of Flat Panel Display FPD touch monitors offers the M150 monitor for desktop
20. ginal Windows display Brightness On H E BRIGHTNESS ee v0 Selecting the Brightness option will allow you to adjust the brightness of the display Adjust the brightness using the lt left and gt right arrow buttons and press SELECT to confirm the new setting 3M Touch Systems Proprietary Information Chapter 3 Video Display Options 25 Contrast a1 OW H B CONTRAST st 7 Selecting the Contrast option will allow you to adjust the contrast of the display Adjust the contrast using the lt left and gt right arrow buttons and press SELECT to confirm the new setting Color RGB ADJUST BLACK LEVEL ADJUST AUTO CONTRAST When you choose the Color option from the OSD this will bring up a sub menu that allows you to adjust the RGB or Black Level color balance for your display Use the lt left and P right arrow buttons to scroll through the color menu You can also use the Auto Contrast feature to automatically adjust the color and contrast of your display By adjusting a single color you can make the picture look warmer biased towards red or cooler biased towards blue Adjusting all three levels will make colors appear more or less striking Position 90 H E POSITION H POSITION V POSITION 3M Touch Systems Proprietary Information 26 M150 FPD Monitor Installation Guide You can use the Position option to center the image on the display manually Use the lt
21. hange or modification to the equipment not expressly approved by the party responsible for compliance could void your authority to operate such equipment This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la classe B respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC Warning To assure continued FCC compliance the user must use grounded power supply cord and the provided shielded video interface cable with bonded ferrite cores If a BNC cable is going to be used use only a shielded BNC 5 cable Also any unauthorized changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device 3M Touch Systems is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment CE Conformity for Europe The device complies with the requirements of the ECC directive 89 336 EEC as amended by 92 31 EEC and 93 68 EEC Art 5 with regard to Electromagnetic compat
22. ibility and 73 23 EEC as amended by 93 68 EEC Art 13 with regard to Safety 3M Touch Systems Proprietary Information Rear Ed f la Base Not Shown M150 Base Plate Mounting Template Cut Line i Drawn actual size 3M Touch Systems Proprietary Information Place this template on mounting surface and drill three holes as shown for mounting screws The screw heads must be smaller than 0 39 10 mm and larger than 0 21 5 5 mm Adjust height of screw heads to securely lock monitor in place This height is about 0 23 6 mm Drill 3 Mounting Holes JAN 4 M _ 1 1 1 1 1 1 1 l L i x s v 1 0 39 10 mm Y y 0 21 5 5 mm Front Edge of Base 3M Touch Systems Proprietary Information
23. les connected properly After you installed TouchWare did you restart your PC to activate the touch screen driver Are the communication settings correct Is the touch screen trying to use the COM port or IRQ of another device for example a mouse If so a hardware device conflict will result and the touch screen will not work Touch screen is not accurate Calibrate the touch screen for the current video resolution and operating system Cursor does not follow finger movement or does not reach the edges of the screen Calibrate the touch screen for the current video resolution and operating system Cursor is not located directly underneath your finger Open the touch screen control panel and make sure all cursor offsets vertical edge horizontal are turned off Calibrate the touch screen for the current video resolution and operating system Cursor is extremely jittery or erratic Stabilize the cursor by adjusting the operating frequency of the touch screen controller using the touch screen control panel Cursor lags finger Power Management Lower the baud rate of the touch screen controller and the touch screen driver The M150 monitor conforms to the Video Electronics Standards Association VESA Display Power Management Signaling DPMS standard To benefit from power management the monitor must be used in conjunction with a computer and video card that implements the VESA DPMS standard The PC aut
24. o purposes e Sets the active area of the touch screen e Aligns the touch screen s active area to the underlying video To calibrate the touch screen open the touch screen control panel and select Calibrate Follow the directions displayed on the screen For more information on calibration refer to the online help or the user documentation 3M Touch Systems Proprietary Information CHAPTER 3 Video Display Options This chapter provides guidelines for adjusting the video display and using the monitor controls to adjust the image to your liking Before you make any adjustments e Be sure to adjust the controls in your normal lighting conditions e Display a test image or pattern whenever you adjust the video Adjusting the M150 Video Display Your M150 FPD monitor has four controls to adjust the video display e MENU Shows or hides the menu e SELECT Highlights the current menu option or saves the current setting Press or lt to change the value e 4 Left Enables you to scroll backwards through items on the menu decrease the value of selected option or move to the previous menu item e M Right Enables you to scroll forward through items on the menu increase the value of selected option or move to the next menu item If you do not press the Menu Select or lt left or gt right adjust buttons for 45 seconds the monitor adjustment program times out and hides the menu options You can press the Menu bu
25. omatically invokes the power management feature if you do not use the touch screen mouse or keyboard for a user defined period of time To restore the video image simply touch the screen press a key or move the mouse M150 Regulatory Agency Approvals Your product complies with the following regulatory standards FCC B CE UL cUL VCCI CCC C tick 3M Touch Systems Proprietary Information 32 M150 FPD Monitor Installation Guide This equipment has been tested and found to comply within limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in residential installations This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may case harmful interference to radio communications However there is no guarantee that interference will not occur ina particular installation If this equipment does cause interference to radio or television equipment reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Move the equipment away from the receiver e Consult the dealer or an experienced radio television technician for additional suggestions A CAUTION You are cautioned that any c
26. or refresh rate refer to your video card documentation Multimedia Features The M150 FPD monitor comes with multimedia features built in It has a microphone and speakers built into the back of the display bezel and includes multimedia cables These cables can be connected from either the rear of the monitor or in front two separate sets of jacks are included Figure 5 Multimedia Cables Optional Card Reader Bracket The M150 FPD monitor is available with an optional card reader bracket and 2 M3 screws that supports IDTech and MagTech brand electronic card readers The M150 has been designed with slots on either side of the bezel to accommodate this card reader bracket Simply slide the bracket into the appropriate holes and pull down slightly to lock in place Refer to the illustration below for wiring suggestions Note that 3M Touch Systems does not supply these card readers Supported MagStripe Readers At the time of publication the following mini magnetic card readers have been tested to fit the 3M Touch Systems optional card reader bracket Consult your card reader sales representative for model numbers not listed here 3M Touch Systems Proprietary Information Chapter 2 Setting Up Your M150 FPD Monitor 17 all MiniMag readers all mini sized readers IDT 3331 02U IDT 3321 33 2180201 IDT 3331 12U IDT 3321 33PP 2180202 IDT 3331 23U IDT 3331 02 2180203 IDT 3331 33U IDT 3331
27. quire flexibility of input including gloved hand use we offer the M150 with a 5 wire resistive touch screen This technology has been tested in a laboratory environment to withstand 35 million mechanical touches without noticeable degradation to the surface Native Video Resolution on a Flat Panel Display Flat panel displays unlike CRTs are optimized to run at one resolution A flat panel display has discrete points that determine the exact location of a pixel Each flat panel display has an exact number of pixels associated with it There is a one to one mapping between the number of pixels and the video resolution A flat panel display should be used at the resolution dictated by the number of pixels on the panel for optimum performance For example the M150 monitor has 1024 pixels across the screen and 768 lines of pixels down the screen and can accurately display this resolution at full screen Options for Using Other Video Resolutions The M150 monitor supports all standard resolutions up to their respective native resolution for monitor setup Many video cards initially display a screen image at the SVGA or VGA resolution By supporting these resolutions the monitor can display the desktop controls that let you change to the optimal resolution of 1024 x 768 Mechanical touches tested in a single x y location using a finger like stylus of 45 durometer A shore hardness 0 5 diameter with a load of 0 46 pounds 0 1 pound of
28. r software media is proven not to have met 3M Touch Systems warranty then 3M Touch Systems sole obligation and User s and Purchaser s exclusive remedy will be at 3M Touch Systems option to repair or replace that Product quantity or software media or to refund its purchase price 3M Touch Systems has no obligation under 3M Touch Systems warranty for any Product software or software media that has been modified or damaged through misuse accident neglect or subsequent manufacturing operations or assemblies by anyone other than 3M Touch Systems 3M Touch Systems shall not be liable in any action against it in any way related to the Products or software for any loss or damages whether non specified direct indirect special incidental or consequential including downtime loss of profits or goodwill regardless of the legal theory asserted 2002 03 3M All rights reserved Document Title M150 Flat Panel Display Touch Monitor User Guide Document Number 19 258 Version 2 5 MicroTouch the MicroTouch logo ChassisTouch ClearTek Microcal ThruGlass TouchPad TouchPen TouchWare TouchTek and ToughTouch are either registered trademarks or trademarks of 3M in the United States and or other countries Microsoft MS DOS Windows Windows NT and Visual C are registered trademarks or trademarks of Microsoft Corporation 3M Touch Systems Proprietary Information Chapter 1 Chapter 2 Contents Overview Important Safety Information
29. s are uniquely within User s knowledge and control it is essential that User evaluate the 3M Touch Systems Product and software to determine whether it is suitable for User s particular purpose and suitable for User s method of application 3M Touch Systems statements engineering technical information and recommendations are provided for User s convenience but their accuracy or completeness is not warranted 3M Touch Systems products and software are not specifically designed for use in medical devices as defined by United States federal law 3M Touch Systems products and software should not be used in such applications without 3M Touch Systems express written consent User should contact its sales representative if User s opportunity involves a medical device application IMPORTANT NOTICE TO PURCHASER Specifications are subject to change without notice These 3M Touch Systems Products and software are warranted to meet their published specifications from the date of shipment and for the period stated in the specification 3M Touch Systems makes no additional warranties express or implied including but not limited to any implied warranties of merchantability or fitness for a particular purpose User is responsible for determining whether the 3M Touch Systems Products and software are fit for User s particular purpose and suitable for its method of production including intellectual property liability for User s application If the Product software o
30. s in the manufacturer s Material Safety Data Sheet and product label To avoid possible environmental contamination which may result in minor or moderate injury Dispose of the flat panel display according to applicable governmental regulations Explanation of Symbols A Attention Read accompanying documentation Important Notes Plug power cord into appropriate power source Plug power cord into a grounded receptacle When unplugging power supply cord pull on plug not cord Do not connect or disconnect this product during an electrical storm Install the display in a well ventilated area Always maintain adequate ventilation to protect the display from overheating and to ensure reliable and continued operation e Do not expose this display to heat Passive heat may cause damage to the case and other parts e Do not install this display in areas where extreme vibrations may be generated For example nearby manufacturing equipment may produce strong vibrations The vibrations may cause the display to exhibit picture discoloration or poor video quality e Ensure that metal does not contact the touch screen 3M Touch Systems Proprietary Information Overview 7 e To avoid ergonomic concerns Do not install the monitor in a manner or location with awkward accessibility Extended use may result in muscle tendon or fixed posture strains It is recommended you take periodic breaks from continuous use Service and
31. te Display Mode Refresh Rate VGA 640 x 480 60 US Text 720 x 400 70 SVGA 800 x 600 56 Hz XGA 1024 x 768 60 Configuring the Display Settings After you connect your M150 FPD and turn on your computer you may need to configure one or more of these display settings The ideal settings for this monitor are as follows e Display mode also called desktop area or video resolution 1024 x 768 e Refresh rate also called vertical scan rate or vertical sync 60 Hz e Color depth also called color palette or number of colors at least 16 bit high color 3M Touch Systems Proprietary Information M150 FPD Monitor Installation Guide Using the Standard Controls for the Video Card In addition to the standard controls on the monitor each video card has several controls that let you adjust the display settings The software and driver for each video card is unique In most cases you adjust these settings by using a program or utility provided by the manufacturer of the video card For example you can use the Windows Display Properties control panel to adjust the desktop area resolution color depth and refresh rate Whenever you change these settings or calibrate the touch screen the image size position or shape may change This behavior is normal You can readjust the image using the monitor controls described in Chapter 3 of this guide For more information on adjusting the desktop area resolution color depth
32. tertop Base Mounting Option Keyhole slots in the bottom of the base plate enable you to secure the unit to a desktop or countertop Use standard screws in the desktop or countertop and then slide the base plate on for a secure fit Note A full size template has been included in the back of this manual for your convenience Simply tear out the template and drill directly through the holes indicated to secure your monitor to any surface Figure 2 Keyhole Mounting Slots F 10 mm 3M Touch Systems Proprietary Information 14 M150 FPD Monitor Installation Guide Access to the Video Controls The controls for adjusting the video display are located on the front of the M150 FPD monitor These buttons let you display the on screen menu and adjust the phase image position contrast and brightness Make sure you have unobstructed access to the video controls once the M150 monitor is installed Figure 3 Video Display Controls MENU Microphon lt Left SELECT gt Right LED Adjusting the Viewing Angle The yoke and spine were designed with touch stability in mind This innovative design keeps the monitor face stable during touch The unit can be adjusted to any locked position from 0 up to 60 degrees from vertical This allows for users of different heights to view the monitor at the angle that best suits them with no degradation in touch stability Turn the positive locking mechanism adjustment knob
33. tton at any time to display the options again Pressing MENU will pull up the On Screen Display OSD menu as shown below Figure 10 M150 Main Menu Options Auto Bright Contrast Color Position Image Misc Config 3M Touch Systems Proprietary Information 24 M150 FPD Monitor Installation Guide Auto Config On H FE AUTO CONFIG YES 1024X768 To perform an Auto Config press the lt left arrow key once then press SELECT The Main Menu item Auto Config is used to adjust the configuration of the phase clock vertical and horizontal position automatically A confirmation box is displayed to confirm the user selection The default selection in the box is NO and is highlighted by a red bar If the Select key is pressed the main menu is redisplayed and nothing is changed When Yes is selected an automatic configuration is started After the process is completed successfully a confirmation box Does this image look correct is displayed If image is correct select Yes to exit confirmation box If image isn t correct select No to go to PHASE item adjustment and adjust the phase manually to the best image quality If you change your display to Windows shut down mode this noise will be more visible and easier to eliminate Click on the Start button and then click Shut Down This will bring you to the Windows shutdown mode After finishing phase adjustment click on the Cancel to return to your ori
34. your M150 FPD refer to the Important Safety Information section at the beginning of this document 3M Touch Systems Proprietary Information 12 M150 FPD Monitor Installation Guide Unpacking Your Touch Monitor Carefully unpack the carton and inspect the contents Your M150 monitor includes the following cables and accessories gt os 15 pin video cable 9 pin RS 232 serial communication cable or USB cable if applicable AC power cable 3M CD with touch screen software documentation and utilities Multimedia audio cables Arm Mounting Option The unit has a 75 mm VESA mounting pattern on the back to allow for arm mount capability Follow the manufacturer s instructions included with the mounting device to properly attach your monitor In order to arm mount the M150 FPD you will need to remove the monitor face from the stand and yoke 3M Touch Systems Proprietary Information Chapter 2 Setting Up Your M150 FPD Monitor 13 Figure 1 Disassembling the Yoke amp Base for Arm Mounting Step 1 Unlock the yoke With the unit laying face down safely and securely on a nonabrasive surface remove the two screws connecting the top of the yoke Lift yoke and pull down to disengage tabs to remove Step 2 Remove the bottom two screws holding the hinge cover in place Remove the small hinge cover Step 3 Remove the inner four screws holding the base to the FPD and gently remove the base Coun
Download Pdf Manuals
Related Search