SignaMax 065-1100NS User`s guide
Contents
1. 14 APPENDIX A GABLDES E d ER ee 15 APPENDIX B ABOUT RJ 45 16 Signamax Q65 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter APPENDIX C APPLICATION DIAGRAM 17 APPLICATION DIAGRAM 17 APPLICATION DIAGRAM 17 APPLICATION DIAGRAM 18 CONTACT 19 Signamax 965 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter INTRODUCTION About This Guide Welcome Thank you for choosing the 100BaseTX to 100BaseFX Media Converter This device integrates Fast Ethernet copper and fiber segments in a highly flexible package Purpose This guide discusses how to install and configure your 100BaseTX to 100BaseFX Media Converter Terms Usage In this guide the term Converter first letter upper case refers to your 100BaseTX to 100BaseFX Media Converter and converter first letter lower case refers to other converters Introduction 1 Signamax Q65 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter Features e Complies with EIA TIA and IEEE standards e Complies with IEEE 802 3u 100BaseTX amp standards MDI MDI X push button selection for RJ 45 port e Supports Half Full Duplex Auto Negotiation e Slide switch to enable2. port fully supports auto sensing and auto negotiation 1 Insert one end of Category 5 twisted pair cable into available RJ 45 port on the Converter and the other end into the port of the network node 2 Check the corresponding port LED on the Converter to make sure that the connection is valid Refer to the LED chart in the next section Installation 13 Signamax 5 1100 5 1110 5 1120 5 Series 100BaseTX FX Media Converter LED INDICATORS This Converter has LED indicators located at the front of the device The LEDs have been designed to give easy at a glance network status and provides real time connectivity information Please see below for an interpretation of their functions LED Indicators Converter is receiving power Off Power off or failure On Illuminated when Green connectors are attached LNK Green through port On Port is operating at full Green duplex duplex Amber at a slower rate No data packets received LED Indicators 14 Cables Signamax 965 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter APPENDIX A The following are some recommendations as to what you should and should not do when installing cables Remember cables are the deciding factor in network performance Try to maintain a bend radius of min 4x the diameter of the cable for UTP and 100x for fiber Place cable ties at regular intervals do not o
3. the bottom of the Converter for grip and to protect the case from scratching MDI MDI X Connection The MDI MDI X function alleviates the worry of cable type configuration used for connecting the converter with a 100BaseTX device Simply follow the chart below when connecting the Converter and use the push button to select MDI or MDI X accordingly Device Cable Selection Configuration Hub or Straight Switch Through Hub or Crossover Switch DTE Straight NIC Through Crossover Selection Table Installation 8 Signamax 9 965 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter MDI X m MDI 100Base T Location of Crossover Switch NWay Push Button Switch Setting Use the NWay push button switch to activate NWay operations Note Factory NWay switch default is set to the ON position ON Activates the NWay auto negotiation operation mode Set NWay switch to ON when connecting to an auto negotiation device The function will determine the highest possible speed and duplex mode in the copper segment OFF Deactivates the NWay auto negotiation operation mode Set the NWay switch to OFF when connecting to an auto sensing device that only supports 10 100 detection Some early switch models only support auto sensing of speed and NOT auto detection of both speed and duplex mode auto negotiation Note Setting the duplex mode is feasible while the media converter is on line Insta
4. SIGNAIMAX CONNECTIVITY SYSTEMS Signamax Connectivity Systems 100BaseTX to 100BaseFX Media Converter Model 065 1100NS Mode 065 1110NS Mode 065 1120NS Series Signamax Q65 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter Signamax Connectivity Systems 100BaseTX to 100BaseFX Media Converter Series 065 1100NS 065 1110NS 065 1120NS User s Guide Signamax 965 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter FCC Warning This equipment has been tested and found to comply with the limits for a class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used accordance with this users guide may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user s own expense CE Mark Warning This is a Class A product In a domestic envronment this product may cause radio interference in which case the user may be required to take adequate measures Signamax Q65 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter Trademarks Product names mentioned in this manual may be trademarks or regis
5. cal current in your country Connecting Fiber Cable When connecting fiber cable to a 100BaseFX port on the Converter be sure the correct type ST or SC connector is used Follow the steps below to properly connect fiber cable 1 Remove and keep the ST SC port s rubber cover When not connected to a fiber cable the rubber cover should be replaced to protect the optics Check that the fiber terminators are clean You can clean the cable plugs by wiping them gently with a clean tissue or cotton ball moistened with a little ethanol Dirty fiber terminators on fiber optic cables will impair the quality of the light transmitted through the cable and lead to degraded performance on the port Connect one end of the cable to the ST SC port on the Converter and the other end to the ST SC port on the other device Check the corresponding port LED on the Converter to be sure that the connection is valid Refer to the LED chart in next section Note When inserting the cable if SC connectors are used be sure the tab on the plug clicks into position to ensure that it is properly seated Installation 12 Signamax Q65 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter A Warning Because invisible laser radiation may be emitted from the aperture of the fiber port when no cable is connected avoid exposure to laser radiation and do not stare into the open apertures Connecting Copper Cable The 100BaseTX RJ45 Ethernet
6. d light 4 Connect cables from the network partner devices to the ports on the front panel The green LNK LED on the front panel associated with the port should light This Converter can also be mounted on a vertical surface Simply use the underside of the unit as a template to measure and mark out the position of the holes on to the surface where the unit is to be installed Then use the two screws provided to mount the Converter firmly in place Warning Please exercise caution when using power tools Also install this unit away from damp or wet locations or in close proximity to very hot surfaces These types of environments can have a detrimental effect on the converter and cables An ideal location is a lightly cooled place such as a typical equipment room Connecting To Power The Converter uses an external power supply rated at 12V DC 0 8A 50 60 Hz 1 Insert the power cable plug directly into the receptacle located at the back of the device 2 Plug the power adapter into an available socket Installation 11 3 Signamax Q65 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter Check the front panel LEDs as the device is powered on to verify that the Power LED is lit If not check that the power cable is correctly and securely plugged in Note For International use you may need to change the AC power adapter cord You must use a power cord set that has been approved for the receptacle type and electri
7. disable auto negotiation operations e Support ST SC and WDM fiber connectors e Extends fiber distance of up to 2km 6600 feet for multimode and up to 60km 198000 feet for long haul single mode Compatible with other 100BaseTX FX devices e Status LEDs e External power supply options e Used with the Mini Converter Chassis for internal power supply e FCC Class A amp CE approved Introduction 2 Signamax 5 1100 5 1110 5 1120 5 Series 100BaseTX FX Media Converter Specifications Standard IEEE 802 3u Connector 1 x ST or SC fiber optic 1 x RJ 45 Max Distance Twisted Pair 100 m 330 ft Full Duplex MM Fiber 2 000 m 6 600 ft SM Fiber 20 km 66 000 ft Long Haul SM Fiber 60 km 198 000 ft Half duplex MM Fiber 412 m 1 360 ft Unit LEDs Power Green illuminated for normal converter operation Port LEDs LNK Green illuminated when connectors are attached RCV Amber flashing or illuminated when receiving packets FD Green illuminates when in full duplex mode Power External power supply 12V DC 0 8A Temperature Operating 32 to 122 F 0 to 50 C Storage 4 to 158 F 20 to 70 C Humidity Operating 1096 to 8096 RH Storage 596 to 9096 RH Emissions FCC Part 15 of Class amp CE approved Dimensions 109 2 x 73 8 x 23 4 mm L x W x H Switches Push button switch MDI MDI X selection for the RJ 45 connector NWay slide switch NWay Auto negotiation ON OFF func
8. ink to a variety of Fast Ethernet network devices within a LAN Application Diagram In the figure below the Converter is functioning as a server aggregation for an enterprise or LAN configuration It is providing a 100Mbps full duplex link to a workgroups of 10 100 switches located on separate floors within a single building Half Duplex Mult mods 41 Ze D 1 T e s pa ME my CH Appendix 17 Signamax 965 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter Application Diagram Ill In the figure below the Converter is functioning as a high speed dedicated link within a campus network configuration It is providing a 100Mbps full duplex link to a remote network node Half Duplex 412 s Appendix 18 Signamax 965 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter CONTACT INFORMATION SIGNAMAX CONNECTIVITY SYSTEMS An AESP Company 1810 N E 144th Street North Miami Florida 33181 U S A Phone 305 944 7710 Fax 305 652 8489 Sales 800 446 2377 Tech Support 800 446 2377 ext 201 Http www signamax com E mail info signamax com EUROPE AESP Ukraine UKRAINE 2 Timiryazevskaya St 47 252014 Kiev Ukraine Phone 380 44 296 53 57 Fax 380 44 294 88 60 Http www aesp com ua E mail aesp aesp com ua AESP Sweden SWEDEN Grevegatan 19 21 5 815 40 TIERP SWEDEN Phone 46 0 293 228 88 Fax 46 0 293 228 89 Pho
9. llation 9 Signamax 965 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter Install the converter This Converter utilizes ports with fiber and copper port connectors functioning under the Fast Ethernet protocol 100BaseTX Port The 100BaseTX port supports a network speed of 100Mbps and can operate in half and full duplex transfer modes This port also offers MDI MDI X crossover detection that gives true plug and play capability just plug in the network cable to the port and adjust the push button according the chart above The RJ 45 connector is suitable for UTP cable Category 3 4 5 or better 100BaseFX Port The 100BaseFX port adds a fiber Fast Ethernet link to your network device Compliant with IEEE 802 3u this port can transmit data at 100Mbps in full duplex mode across distances of up to 2km through multimode fiber optic cable The fiber port has a choice of ST or SC fiber connector types for multimode models and SC connectors are used on singlemode models Installation 10 Signamax 965 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter Desktop Installation Follow the instructions listed below to install the Converter onto a desktop location 1 Locate the Converter in a clean flat and safe position that has easy access to AC power 2 Affix the four 4 selfadhesive rubber pads to the underside of the Converter 3 Apply AC power to the Converter The green PWR LED on the front panel shoul
10. mode since the maximum spanned distance is limited to 412 meters Hardware Description 5 Signamax 5 1100 5 1110 5 1120 5 Series 100BaseTX FX Media Converter Front Panel View with ST and RJ 45 Connectors Hardware Description 6 Signamax Q65 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter INSTALLATION Installing Your Converter In this chapter we will take a look at how to install converters within its operating environment First it is important to unpack the Converter and ensure that all the components listed in Package Contents are present Location MDI MDI X Connection NWay Push Button Switch Setting Installing Converter Desktop Installation Powering On Unit Connecting Fiber Cable Connecting Copper Cable Location The location selected for installing the Converter may greatly affect its performance When selecting a site we recommend considering the following rules 1 Install the Converter in a fairly cool and dry place See Technical Specifications for the acceptable temperature and humidity operating ranges Installation 7 Signamax 965 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter 2 Install the Converter in a location free from strong electromagnetic field generators such as motors vibration dust and direct exposure to sunlight 3 Leave at least 10 cm of space at the front and rear of the unit for ventilation 4 Affix the provided rubber pads to
11. ne 49 8 1 35 9303 0 Http www aesp se E mail info aesp se JOTEC AESP AS NORWAY Telefon 23 14 17 00 Ordrefax 23 14 17 10 Karihaugveien 102 Postboks 50 Ellingsrudasen 1006 Oslo Norway Phone 47 23 14 1700 Fax 47 23 14 1710 Http www jotec no E mail jotec jotec no AESP Russia RUSSIA Kronshtadtsky Blv 125499 Moscow Russia Phone 7 095 456 0704 Phone 7 095 456 0344 Fax 7 095 454 3040 Http www aesp ru E mail aesp aesp ru AESP Germany GmbH GERMANY Weisserfelderstr 2 D 85551 Kircheim b M nchen Germany Phone 49 89 901 097 0 Fax 49 89 901 097 22 E mail aesp info t online de INTELEK spol s r o CZECH REPUBLIC Vlarska 22 Brno CZ 62700 CZE Czech Republic Phone 420 5 481 27248 Fax 420 5 48 1 27247 Http www intelek cz E mail info intelek cz Contact Information 19
12. tered trademarks of those products and are hereby acknowledged e Ethernet is a trademark of Xerox Corporation Microsoft Windows is a trademark of Microsoft Corporation Signamax Connectivity Systems is a trademark of Advanced Electronic Support Products Inc Signamax 9 965 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter TABLE OF CONTENTS CHAPTER 1 INTRODUCTION 1 ABOUT THIS 1 5 5 E ANE 2 PACKAGE 4 CHAPTER 2 HARDWARE DESCRIPTION 5 PRODUCT OVERVIEW 5 CHAPTER 3 INSTALLATION 6 INSTALLING YOUR 6 LOCATION 5 7 MDI MDI X CONNECTION 8 NWay PUSH BUTTON SWITCH SETTING 9 INSTALL THE CIBVERTER 10 DESKTOP 10 POWERING ON 11 CONNECTION FIBER 12 CONNECTION COPPER 13 CHAPTER 4 LED 14 LED 5
13. tion for the RJ 45 connector Introduction 3 Signamax Q65 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter Package Contents The 100BaseTX to 100Base FX Converter packaged should include e converter e One AC adapter for external power supply Four pieces self adhesive pads e One user s manual Introduction 4 Signamax 965 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter HARDWARE DESCRIPTION Product Overview The Converter is primarily designed for larger workgroups demanding more speed and bandwidth and requiring expansion of the Fast Ethernet network It features a MDI MDI X crossover push button switch for direct connection to the workstation switch or hub Now the network manager does not need to worry about the cable configuration crossover straight through when establishing a connection between RJ 45 ports The Converter features both a RJ 45 jack and a ST SC or WDM fiber optic connector that allows it to connect a 100BaseTX copper network to the 100BaseFX fiber network It features Auto Negotiation support which allows the Converter to support connections with leading NWay capable Switches At full duplex the Converter can create potential distances of up to 2 kilometers for multimode fiber and 60 kilometers for long haul single mode fiber between a LAN switch hub or a file server Note It is not recommended to use the Converter in half duplex
14. ver tighten cableties try to avoid using with fiber Appendix A Try not to allow the cable to twist too much this creates a strain on the internal cables Do not stretch the cable especially on Corners in vertical cable trays and when spanning long distances 15 Signamax 965 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter APPENDIX B About RJ 45 Cables When connecting your network devices use standard Category 3 eight way cables for 10Base T configurations and Category 5 cable for 100BaseTX The pin assignments are as follows Pin 1 TD Pair 2 White Orange Pin 2 TD Pair 2 Orange White Pin 3 RX Pair 3 White Green Pin 4 N A Pair 1 Blue White Pin 5 N A Pair 1 White Blue Pin 6 RX Pair 3 Green White Pin 7 N A Pair 4 Brown White Pin 8 N A Pair 4 Brown White Application Cable Type Application Converter Converter Hub to End Converter Straight through 1 4 1 Cable 2 2 Network Adapter Converter to Switch 34 ee Da K Converter Converter End 1 End 2 Cross Over 1 1 Cable 2 2 3 3 16 6 Appendix 16 Signamax Q65 1100NS 1110NS 1120NS Series 100BaseTX FX Media Converter APPENDIX C Application Diagram In the figure below the Converter is functioning as a high speed bridge between switches creating increased capacity for each user node on the local area network It is providing a 100Mbps full duplex l
Download Pdf Manuals
Related Search