Audiovox SIR-CK2 Owner`s manual
Contents
1. M4 Screw M4 x 8mm 4 pcs 4 pcs 3 4 W X 3 Long Flat Washer M4 Double Sided Tape 1 pc 4 pcs OPTIONAL Alcohol Swab FM Switching Box Assy P N SIR SWB 6 Meter 7 f pc 1 pc 128 6813D 4 of 16 Installation Wiring Precautions 1 To prevent a short circuit be sure to turn off the ignition and remove the negative battery cable prior to installation Connect power wires last 2 Do not install the unit in the locations exposed to direct sunlight or in areas subject to extreme temperatures 3 Incorrect installation may cause damage to the system Mount the unit firmly in place using the supplied hardware Be careful not to damage the vehicle wiring Be sure to use the supplied screws and washers Be careful not to snag any wires when tightening screws Setting Up and Installing Your Kit NOTE The SIRIUS signal can be received and processed virtually anywhere as long as there are no obvious satellite signal obstructions such as nearby buildings high terrain parking garages or tunnels 1 Cabling Interconnections You can begin to enjoy Sirius Satellite Radio as soon as the Shuttle and Vehicle Kit installation are complete Set up your Audiovox Shuttle using the following installation instructions or enlist the help of a professional installer 2 Installing the Cradle Mount Base Assembly NOTE The fins on the mounting base are pliable and can be bent to co2. Without FM Modulator 2 128 6813D 2 of 16 Cautions and Warnings 1 Do not install the Shuttle in a position that hinders your view through the windshield or obstructs view ing of the dashboard indicators and displays Do not install the unit where it may obstruct the operation or deployment of safety devices such as airbags etc Do not allow operation of the unit to detract from safe driving practices remember that you are responsible as the vehicle operator to adhere to all safe driving and traffic regulations This unit complies with the interference limits relative to a Class B digital device applicable under Part 15 of the FCC Rules regarding installation in a residential environment If the unit is not installed in accordance with these instruc tions it could cause harmful interference to radio or television reception If this condition persists after corrective action consult your dealer or experi enced installation facility By adhering to these warnings and safety consider ations serious accidents and or personal injury can be avoided 128 6813D 3 of 16 Contents SIR CK1 and SIR CK2 Install Manual Base P N 1286813C P N 136C3484 1 pe 1 pe 1 pe Antenna Cradle CK1 P N 13603471 P N 118 1130 or Cradle CK2 P N 136D3479 DC Power Adapter P N 112B3294 1 Audio Cable P N 112B3293 HARDWARE pw 150 1519 Phillips Machine Split Lock Washer
3. AUDIOVOX ELECTRONICS CORP SIRIUS SHUTTLE Vehidelnstalation Guides SIR CK1 and SIR CK2 128 6813D 1 of 16 Revision A Changed the Switching Box Part Number to SIR SWB 9 29 03 Revision B Corrected Part Number for DC Power Adapter 112B3294 and added pages for formatting purposes 2 9 04 Rev C Changed antenna part number and CK2 part number4 7 04 Rev D Changed cradle and shuttle connector and image 4 27 04 Congratulations You are one step closer to experiencing Sirius Satellite Radio Sirius will revolutionize your in home or vehicle entertainment with 100 streams of original programming including 60 streams of completely commercial free music guaranteed 40 streams of news sports and entertainment Coast to Coast reception and Digital quality sound All music content is selected and developed in house by Sirius team of Master Music Programmers talented and seasoned professionals who love the music as much as the listeners World class partners such as ESPN ABC CNBC Bloomberg Discovery and Radio Disney are developing news sports and entertainment programming Your Audiovox Shuttle must be used with an adapter kit such as the Audiovox Home kit or Vehicle Boat Kit as required by your specific installation needs These kits are available at retailers where Audiovox main units are sold Audiovox Home Kit SIR HK1 Audiovox Vehicle Kit SIR CK1 With FM Modulator Audiovox Vehicle Kit SIR CK2
4. TION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 48 MONTHS FROM DATE OF ORIGINAL PURCHASE IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESS OR IMPLIED WHATSOEVER No person or representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you This Warranty gives you specific legal rights and you may also have other rights which vary from state to state U S A AUDIOVOX CORPORATION 150 MARCUS BLVD HAUPPAUGE NEW YORK 11788 1 800 645 4994 CANADA CALL 1 800 645 4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA 128 6464 J 128 6813D 15 of 16 2004 Audiovox Electronics Corporation 128 6813D 128 6813D 16 of 16
5. The Shuttle and Cradle provide an audio output signal in three manners 1 When using CK1 or 2 cradle the audio signal can be routed through an audio cable which is applied to the auxiliary inputs of a radio or entertainment system 2 When using the CK1 cradle the audio signal be transmitted to a car radio on one of four selectable FM frequencies The audio signal can then be played through your car radio when the car radio is tuned to one of these frequencies 3 Some listeners prefer to use a hard wired FM transmitter In this instance when using the CK1 cradle an optional FM Switching Box assembly Part No SIR SWB is available and provides a hard wired FM output when connected to the FM OUT connector on the left side of the cradle the other end of the switching box plugs into the antenna jack of your radio By using this assembly and selecting the appropriate FM output frequency 88 1 MHz 88 3MHz 88 5MHz or 88 7MHz with the slide switch the Sirius signal received at the ANT cradle antenna input can be played through your car radio when tuned to one of these frequencies FM OUT FM FREQUENCY SELECT SLIDE SWITCH 88 1 MHz 88 3 MHz 88 5 MHz 88 7 MHz SHUTTLE CRADLE CK1 10 128 6813D 10 of 16 7 Mounting the Vehicle Antenna The antenna should be placed on a relatively flat surface on the vehicle exterior preferably on the roof high point or on the trunk convertible To
6. ake adjustments and take up slack whenever necessary At the lowest point of the rear window route the cable into the trunk taking advantage of existing cable conduits Then snake the cable around the passenger compartment to the back of the Sirius cradle In SUV s minivans etc route the cable into the vehicle under the rubber molding of the hatch door or tailgate and then under the interior trim NOTE Avoid exposing the cable in the driver and passenger areas where it could become entangled in feet or other objects 12 ANTENNA ROUTING THE CABLE 128 6813D 12 of 16 Plug the antenna cable into the ANT connector on the back of the cradle then plug the cigarette lighter adapter into the lighter receptacle The integral power LED of the power button will light red You are now ready to enjoy Sirius programming within your vehicle CAUTION You could drain the vehicle battery if the cigarette lighter adapter remains plugged in after the ignition is turned off Unplug the adapter to prevent this possibility 43 128 6813D 13 of 16 THIS PAGE LEFT BLANK INTENTIONALLY 128 6813D 14 of 16 D AUDIOVOX 12 MONTH LIMITED WARRANTY CORPORATION AUDIOVOX CORPORATION the Company warrants to the original retail purchaser of this product that should this product or any part thereof under normal use and conditions be proven defective in material or workmanship within 12 months from
7. at head screws your vision block air bag s or securing the plate to the cradle and remove obstruct vehicle dashboard the plate Save the two screws for reassembly controls and or radio CD casette operational displays NOTE The adhesive backing on the base REAR will not permit easy repositioning once MOUNTING Se AIA it has been mated to the surface use PLATE ce D 2 extreme care and planning when EN on selecting the mounting location If the MOUNTING SP CRADLE base is to be screwed to the surface PLATE ASSEMBLY make sure the area in back of the J TYPICAL mounting surface is clear of wires or FN other items to prevent unintentional As shown in the figure unscrew the star nut c Using the alcohol swab supplied with your kit and ball strut assembly from the mounting clean the mounting surface and thoroughly wipe base threaded socket then remove the flat the area dry with a clean lint free cloth head screw lockwasher and flatwasher from the end of the ball strut 128 6813D 7 of 16 f lt T Insert the end of the ball strut into the keyed opening on the cradle mounting plate and secure the plate to the ball strut using the flatwasher lockwasher and flat head screw through the back of the plate Reattach the mounting plate assembly to the rear or bottom of the cradle assembly as desired using the two flat head screws remove
8. d clean the mounting surface as before c Peel the backing from one side of the tape and press the tape in place on the rear or bottom cradle mounting plate d Peel the backing from the exposed side of the tape and carefully position the cradle on the mounting surface gently pressing the cradle into place 9 Using Other Manufacturer s Mounts The Shuttle Cradle can also be installed using other manufacturer s mounts the mounting plate provisions on the rear and bottom of the cradle provide you with multiple mounting options within the vehicle using various vehicle specific aftermarket brackets such as those purchased separately from Panavise Pro Fit etc Installing the Shuttle into the Cradle The Shuttle cradle has three retaining clips one on top and two on the bottom Place the Shuttle in the cradle so that the Shuttle connectors are lined up use the RF connector as a guide Then gently press in on the bottom of the Shuttle to engage the connector The top clip will automatically engage then slide the two bottomclips back into the locked position Cradle orientation can be adjusted by loosening the star nut and then tightening it when the cradle is in the desired viewing position 128 6813D 9 of 16 TOP RETAINING 16 PINSYSTEM CLIP NNECTOR yn ANT o J I p BOTTOM y BOTTOM LEFT SLIDE RIGHT T SLIDECLIP 6 Sirius Program Listening Options
9. d previously Installation of the mounting base can now continue FLAT HEAD SCREW LOCKWASHER CRADLE MOUNTING FLATWASHER a PLATE a STARNUT O BALL STRUT THREADED SOCKET DA MOUNTING BASE If the outside air temperature is cold it may be beneficial to warm the adhesive backing on the base using a portable hair dryer or by holding the backing surface in front of a vehicle heater vent Remove the plastic liner from the adhesive backing on the base and fix the base in position on the surface make sure the mounting pad is accurately positioned on the first try since repositioning may be Bend the fins on the base so it conforms to the mounting surface If the mount is to be screwed in place do not remove the plastic liner from the adhesive backing Use appropriate sheet metal or machine screws for this purpose 128 6813D 8 of 16 NOTE Allow a 72 hour period for the adhesive backing to cure completely k Using the star nut attach the cradle assembly to the base threaded socket do not overtighten the star nut 3 Installing the Cradle Using Double Sided Tape You can mount the cradle directly to your dashboard or other flat surface without using the cradle mount in the kit To do this do not remove either of the mounting plate assemblies from the cradle a Remove the 3 4 x 3 double sided tape from the supplied kit b Determine the location of the cradle an
10. mount the antenna a Plug the antenna into the ANT connector on the back of the cradle b Place the antenna at the preferred location on the roof or trunk surface If the vehicle is equipped with a roof or trunk rack the antenna may have to be mounted off center on the surface The magnet will secure the antenna in the desired position c Apply power to the Shuttle system as outlined in the associated User Guide and obtain an audio output If no audio is heard first check the signal strength indicator located on the bottom left corner of the display to ensure the antenna is receiving an optimum signal If necessary move the antenna to different positions on the surface until an audio output is heard This is the desired antenna position and should be marked with masking tape or by another non scratch method 11 SHUTTLE TYPICAL 12 VDC ADAPTER SAT ANTENNA TYPICAL 7 2 After determining the optimum position turn off Shuttle power disconnect the power adapter from the vehicle cigarette lighter receptacle and disconnect the antenna cable 128 6813D 11 of 16 Plan the routing of the antenna cable to the Shuttle RF input Make sure you avoid any obstructions that could crimp kink or twist the cable use protective grommets wherever rough openings are encountered Route the cable from the antenna position to the interior of the vehicle working the cable under the rear window molding m
11. nform to most mounting surfaces a Interconnect all of the components as shown on the adjacent page to verify that the system operates normally Locate firm reasonably flat surface within your car to permit optimum viewing and line of sight access by the supplied remote control unit 128 6813D 5 of 16 Interconnect Diagram AUDIO CABLE SHUTTLE CRADLE CK1 OR CK2 TO AUXILIARY AUDIO INPUT OF RADIO OR Interconnect Diagram FM Option FM FREQUENCY SELECTION SWITCH SELECT 1 OF 4 AVAILABLE FREQUENCIES AND SET YOUR EXISTING CAR RADIO TO THE SAME FREQUENCY VEHICLE VEHICLE RADIO FM RADIO ANTENNA SHUTTLE CRADLE ONLY A zz A Fer DC POWER ENTERTAINMENT SYSTEM E ADAPTER 7 TO VEHICLE TO VEHICLE A 12 VDC POWER 12 VDC POWER RECEPTACLE RECEPTACLE NOTE 1 THE FM TRANSMITTER OPTION MUST BE SET TO FM ON IN THE SHUTTLE a USER MENU REFER TO THE OWNER S MANUAL PUBLICATION 128 6812 2 WHEN THE FM TRANSMITTER IS TO DC POWER BE USED DO NOT CONNECT THE SHUTTLE ADAPTER SHUTTLE AUDIO CABLE TO THE AUDIO OUT ANTENNA ANTENNA CONNECTOR OF THE SHUTTLE 6 6 of 16 d The cradle contains two mounting plates CAUTION not install the mounting base one on the rear and one on the bottom on a leather or fabric surface or After deciding which configuration to use in a position that could impair loosen and remove two fl
12. the date of original purchase such defect s will be repaired or replaced with new or reconditioned product at the Company s option without charge for parts and repair labor To obtain repair or replacement within the terms of this Warranty the product is to be delivered with proof of warranty coverage e g dated bill of sale specification of defect s transportation prepaid to an approved warranty station or the Company at the address shown below This Warranty does not extend to the elimination of externally generated static or noise to correction of antenna problems to costs incurred for installation removal or reinstallation of the product or to damage to tapes compact discs speakers accessories or vehicle electrical systems This Warranty does not apply to any product or part thereof which in the opinion of the Company has suffered or been damaged through alteration improper installation mishandling misuse neglect accident or by removal or defacement of the factory serial number bar code label s THE EXTENT OF THE COMPANY S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND IN NO EVENT SHALL THE COMPANY S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT This Warranty is in lieu of all other express warranties or liabilities ANY IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY ANY AC
Download Pdf Manuals
Related Search