Home

Yamaha NS-P20 Owner`s manual

image

Contents

1. arising from their sales purchase contract 6 En YAMAHA W W p PRINTED WITH ZOSO NK YAMAHA CORPORATION 2011 Yamaha Corporation Printed in China Y WY60290
2. 25 meter 82 ft speaker cable to make five cables 10 mm 3 8 for connecting the two front speakers center speaker and the two surround speakers 7 Cut the included speaker cable to suitable A lengths for the front center and surround i speakers You need five cables Good No Good 2 Remove about 10 mm 3 8 of insulation from Notes the end of each speaker cable e Make the speaker cables as short as possible Do not bundle or roll up excess cable e Twist the bare wires tightly so the individual strands are not splayed e Be careful not to injure yourself while preparing the speaker cables 3 En E Operating the speaker terminals Negative Positive Note Make sure the Tn terminal is gripping 2 the bare wire not the insulation a Sz ae r 1 Press and hold the terminal tab 2 Insert the bare wire 3 Release the tab so that it closes securely on the bare wire not the insulation 4 Test the security of the connection by pulling gently on the cable Notes e Make sure the bare wires do not touch each other as this could damage the speaker or the amplifier e Ifthe connections are faulty you will hear no sound from the speakers E Connecting the speakers Connect each speaker to the appropriate speaker terminals on your amplifier by using the cables you prepared earlier See the Connection diagram on page 3 for reference Make sure you connect the speakers with th
3. 5 YAMAHA NS P20 NS B20 NS C20 NS SW20 SPEAKER PACKAGE 2 Advanced Y S T OWNER S MANUAL Please read the following operating precautions before use Yamaha will not be held responsible for any damage and or injury caused by not following the cautions below 1 To assure the finest performance please read this manual carefully Keep it in a safe place for future reference 2 Install the speakers in a cool dry clean place away from windows sources of heat sources of excessive vibration dust moisture or cold Avoid sources of electrical humming e g transformers and motors To prevent fire or electric shock do not expose the speakers to rain or water 3 To prevent the enclosure from warping or discoloring do not expose the speakers to direct sunlight or excessive humidity 4 Avoid installing the speakers where foreign objects may fall onto them and or where they may be exposed to liquid dripping or splashing 5 Do not place the following objects on top of the speakers Other components as they might damage or discolor the surface of the speakers Burning objects e g candles as they might cause fire damage to the speakers or personal injury Containers of liquid as they might spill and cause electric shock to the user or damage to the speakers 6 Do not place the speakers where they are liable to be knocked over or struck by falling objects Stable placement will also ens
4. from the AC power source as long as it is connected to the wall outlet even if this unit itself is turned off In this state this unit is designed to consume a very small quantity of power For U K customers If the socket outlets in the home are not suitable for the plug supplied with this appliance it should be cut off and an appropriate 3 pin plug fitted For details refer to the instructions described below Note The plug severed from the mains lead must be destroyed as a plug with bared flexible cord is hazardous if engaged in a live socket outlet SPECIAL INSTRUCTIONS FOR U K MODEL IMPORTANT THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE Blue NEUTRAL Brown LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED Make sure that neither wire is connected to the earth terminal of a three pin plug 5 Information for Users on Collection and Disposal of Old Equipment This symbol on the products packaging and or accompanying documents means that used electrical and electronic products should not be mixed with general house
5. lbs E Subwoofer NS SW20 TY Pe oeeie Advanced Yamaha Active Servo Technology Driv oninu 16 cm 6 1 2 cone woofer non magnetic shielding type Amp output power 50 W 100 Hz 5 Q 10 T H D Amp dynamic powet s sesesssesesseesesessessssrsssssssess 100 W 5 Q0 Input impedance INPUT 1P RCA pin jack 10 KQ Frequency response 1 0 00 eee eseesecseeseeeeeeeseees 30 Hz 160 Hz Input sensitivity INPUT 1P RCA pin jack 80 mV 50 Hz 50 W 5 Q Power supply U S A and Canada models ceeeeeeeees AC 120 V 60 Hz Australia Modelarea AC 240 V 50 Hz U K and Europe models eceeseeeeeees AC 230 V 50 Hz China Korea Asia and General models AC 110 120 220 240 V 50 60 Hz Dimensions W x H x D ue 262 x 264 x 299 mm 10 3 8 x 10 3 8 x 11 3 4 Welt ht sissies niin aicsaasi natin 7 0 kg 15 4 lbs Specifications are subject to change without notice Limited Guarantee for European Economic Area EEA and Switzerland Thank you for having chosen a Yamaha product In the unlikely event that your Yamaha product needs guarantee service please contact the dealer from whom it was purchased If you experience any difficulty please contact Yamaha representative office in your country You can find full details on our website http europe yamaha com warranty The product is guaranteed to be free from defects in workmanship or materials for a period of two years from the dat
6. lengths for the front center and surround Non skid pads When speakers Take care to prevent placing the speakers on injury when preparing the cables a flat surface affix the included non skid pads to the corners of the speaker undersides as shown The pads will Non skid pad Eo prevent the speaker Voy oj from moving around Non skid pads 24 pcs x1 For the front center and surround speakers Including 4 spare non skid pads Installing the speakers Before you connect the speakers place each speaker in its respective location Speaker positioning is very important as it affects the overall sound quality of the Sant SSS Front ron VY right system Place the speakers in locations that will 7 left T Ci optimize the sound quality at your listening position EE Refer to the illustration Center oe ue Subwoofer The position of the subwoofer is not as critical as the position of the other speakers because sub bass sounds are not very directional Refer to Installing the subwoofer on page 2 for more information Note e Placing the speakers too close to a CRT type TV may impair the picture color or cause a buzzing noise In this case move the speakers at least 20 cm Surround Surround 8 away from the TV This is not an issue with LCD left right and plasma TVs 1 En Installing the speakers Installing the front center and surround speakers Front speakers Place the two fr
7. the wires connected to other equipment Never pull the wires themselves Never put a hand or a foreign object into the port located on the right side of this unit When moving this unit do not hold the port as it might cause personal injury and or damage to this unit Since this unit has a built in power amplifier heat radiates from the rear panel Place the unit away from walls allowing at least 20 cm 8 of space above behind and on both sides of the unit to prevent fire or damage Furthermore do not position the unit with the rear panel facing down on the floor or other surfaces When using a humidifier be sure to avoid condensation inside this unit by allowing enough space around the unit and avoiding excess humidification Condensation might cause fire damage to the unit and or electric shock Do not cover the rear panel of this unit with a newspaper tablecloth curtain etc to avoid obstructing heat radiation If the temperature inside the unit rises it may cause fire damage to the unit or personal injury Do not plug this unit into a wall outlet until all connections are complete The voltage to be used must match that specified on the rear panel Using this unit with a voltage higher than specified is dangerous and may cause fire damage to the unit and or personal injury Yamaha is not responsible for damage resulting from use of this unit with a voltage other than specified Super bass sound reproduced by this unit m
8. ay cause a turntable to generate audio feedback In this case move the unit away from the turntable This unit may be damaged if certain sounds are continuously output at high volume level For example if 20 Hz 50 Hz sine waves from a test disc or bass sounds from an electronic instrument etc are continuously output or if a turntable stylus touches the surface of a disc reduce the volume level to prevent the unit from being damaged If you hear distorted noise 1 e unnatural intermittent rapping or hammering sounds from this unit reduce the volume level Extremely loud movie soundtrack low frequency bass heavy sounds or similarly loud popular music passages can damage this unit Vibration generated by super bass sound may distort images on a TV In this case move the unit away from the TV set When disconnecting the power cord from the wall outlet grasp the plug do not pull the cord When you plan not to use this unit for a long period of time i e vacation etc disconnect the AC power plug from the wall outlet Install this unit near the wall outlet and where the AC power plug can be reached easily Precautions e VOLTAGE SELECTOR For China Korea Asia and General models The voltage selector switch on the rear panel of this unit must be set to your local main voltage BE FORE plugging this unit into the AC main supply Voltages are 110 120 220 240 V AC 50 60 Hz This unit is not disconnected
9. e correct polarity positive terminals to positive terminals and negative terminals to negative terminals If you get them crossed over the sound will be unnatural and lack bass In your AV receiver s speaker size settings specify small or S for all of the NS P20 speakers If youre connecting the subwoofer to a Yamaha DSP amplifier or AV receiver connect to its SUBWOOFER or LOW PASS output Connecting the power cables Once you ve completed all of the speaker and subwoofer connections plug the subwoofer amplifier and your other AV components into suitable AC wall outlets Using the Subwoofer Rear panel 1 Power indicator Lights up when the POWER switch is set to ON goes off when the POWER switch is set to OFF 2 INPUT jack Input jack for connecting the line level subwoofer output on your amplifier 3 VOLUME control Adjusts the volume of the subwoofer Turn it clockwise to increase the volume counterclockwise to decrease the volume 4 En 4 POWER switch Set this to ON to turn on the subwoofer Set it to OFF to turn off the subwoofer Setting the subwoofer volume The very first time you use the subwoofer you need to set the volume balance between the subwoofer and the front speakers as follows 7 Turnon your other AV components 2 Set the subwoofer s VOLUME control to minimum 0 3 Set the subwoofer s POWER switch to ON The power indica
10. e of the original purchase Yamaha undertakes subject to the conditions listed below to have the faulty product or any part s repaired or replaced at Yamaha s discretion without any charge for parts or labour Yamaha reserves the right to replace a product with that of a similar kind and or value and condition where a model has been discontinued or is considered uneconomic to repair Conditions 1 The original invoice or sales receipt showing date of purchase product code and dealer s name MUST accompany the defective product along with a statement detailing the fault In the absence of this clear proof of purchase Yamaha reserves the right to refuse to provide free of charge service and the product may be returned at the customer s expense 2 The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area EEA or Switzerland 3 The product must not have been the subject of any modifications or alterations unless authorised in writing by Yamaha 4 The following are excluded from this guarantee a Periodic maintenance and repair or replacement of parts due to normal wear and tear b Damage resulting from 1 Repairs performed by the customer himself or by an unauthorised third party 2 Inadequate packaging or mishandling when the product is in transit from the customer Please note that it is the customer s responsibility to ensure the product is adequately packaged when ret
11. hold waste For proper treatment recovery and recycling of old products please take them to applicable collection points in accordance with your national legislation and the Directives 2002 96 EC By disposing of these products correctly you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling For more information about collection and recycling of old products please contact your local municipality your waste disposal service or the point of sale where you purchased the items Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union If you wish to discard these items please contact your local authorities or dealer and ask for the correct method of disposal Contents Package contents Connecting the speakers Installing the speakers Connection diagram Installing the front center and surround Connecting the power cables speakers Using the Subwoofer Installing the subwoofer Setting the subwoofer volume Wall mounting the speakers Troubleshooting Specifications Package contents Make sure the package contains the following items Subwoofer NS SW20 x1 Front and surround speakers NS B20 x4 Subwoofer cable 5 m 16 ft x1 Center speaker NS C20 x1 Speaker cable 25 m 82 ft x1 To be cut into 5
12. ont speakers on the left and right sides of the TV facing directly forward Surround speakers Place the left and right surround speakers behind your listening position facing slightly inward The front and surround speakers can be placed on a flat surface or wall mounted See Wall mounting the speakers for more information Center speaker Place the center speaker centrally between the front speakers facing directly forward Installing the subwoofer Place the subwoofer on the outside of either the right or the left front speaker as shown in A and B Note Standing waves may make it difficult to hear bass sounds here F Subwoofer _ Front speaker The placement shown in C is also possible however if the subwoofer is placed directly facing a wall and your listening position is in the center of the room you may not be able to obtain enough bass sound from the subwoofer This is because standing waves are forming between the two parallel walls and cancelling out the bass sounds In this case position the subwoofer at an angle to the wall It may be necessary to break up parallel wall surfaces by placing bookshelves etc along them 2 En Wall mounting the speakers You can mount the speakers on the wall as follows 7 install screws into a solid wall or wall support as shown below Use 3 5 to 4mm 1 8 diameter self tapping screws 2 Hang each speaker by its keyhole slots onto the pro
13. to ON but the subwoofer properly cable is connected properly doesn t work There s no sound The VOLUME control is set to 0 Turn Turn up the VOLUME contro sd Turn up the VOLUME contro sd VOLUME control The subwoofer cable is not Make sure the subwoofer cable is connected properly connected properly The subwoofer is too The source material doesn t Try playing source material that contains more bass quiet contain much bass Bass sounds are being cancelled Reposition the subwoofer or break up parallel wall surfaces out by standing waves by placing bookshelves or other large objects along the wall 5 En Specifications E Front surround speakers NS B20 and center speaker NS C20 DVD reise R Full range acoustic suspension non magnetic shielding type DEINE nananana a i 7 cm 2 3 4 cone type Nominal input power s essesesessesesssesesessesesesesesessesesesese 30 W Maximum input powet oseessessesseesessssessesresrsssssessessse 100 W Impedance serna EEE 60 Frequency response INS Be Os aca ateate een tees 70 Hz 25 kHz 10 dB 45 kHz 30 dB INH Oin OEA 65 Hz 25 kHz 10 dB 45 kHz 30 dB Sensitivity NSB Z0 aee a a 83 dB 2 83 V 1 m NSC 2O 84 dB 2 83 V 1 m Dimensions W x H x D NS B20 115 x 176 x 88 mm 4 1 2 x 6 7 8 x 3 1 2 INS 20 ties icons cece 291 x 101 x 103 mm 11 1 2 x 4 x 4 Weight INS B2 rA AN eeu th uiar oes 0 48 kg 1 06 lbs NSS 2 Os AA 0 68 kg 1 50
14. tor on the rear panel lights up 4 Play a audio source that contains low frequency bass sounds Set the amplifier s volume control to a suitable level 5 Turn the subwoofer s VOLUME control up gradually until you achieve a good balance between the subwoofer and the other speakers Notes e Once the subwoofer volume has been set you can leave the subwoofer s VOLUME control set as it is and use your amplifiers volume control to adjust the volume of the entire system e If you replace the front speakers NS B20 with other speakers you will need to re adjust the subwoofer s volume Troubleshooting If this product doesn t work as expected look for a possible cause below If the issue you are experiencing is not listed or you cannot resolve it after reading through these instructions disconnect the power cable and contact an authorized Yamaha dealer or service center E Front surround speakers NS B20 and center speaker NS C20 issue _ Possiblecause T There s no sound The speaker cables are not Make sure the speaker cables are connected properly connected properly The sound is very quiet The speaker cables are not Make sure the speaker cables are emer A connected properly L left to L R right to R to and to E Subwoofer NS SW20 Possible cause The POWER switch is set The power cable is not connected Set the POWER switch to OFF then make sure the power
15. truding screws Note Make sure the shaft of the screw is seated in the narrow part of the keyhole slot Otherwise the speaker may fall Wall wall NS B20 support 6mm 1 4 Minimum 20 mm 3 4 150 mm NS C20 M 5 7 8 ia Warnings NS B20 speaker weighs 0 48 kg 1 06 lbs and NS C20 speaker weighs 0 68 kg 1 50 Ibs Do not mount the speakers on thin plywood or on a wall with a soft surface material Otherwise the screws may pull out of the surface and the speakers may fall possibly damaging the speakers or causing personal injury Do not affix the speakers to a wall using nails adhesives or unstable hardware Long term use and vibration may cause the speakers to fall To avoid accidents resulting from tripping over loose speaker cables affix the cables to the wall Mount the speakers in a wall location that will be unlikely to result in injury to an individual s head Connecting the speakers Caution Make sure the power cables for the subwoofer and your other AV components are disconnected from the AC wall outlets before making any connections Connection diagram Surround speakers Right Left Center speaker Amplifier Note The exact layout of the speaker terminals depends on your amplifier Subwoofer To AC wall outlet E Preparing the speaker cables 3 Twist the bare wires tightly Once you ve positioned the speakers you ll need to cut the
16. ure better sound performance 7 Placing the speakers on the same shelf or rack as the turntable can result in feedback 8 Any time you note distortion reduce the volume control on your amplifier to lower setting Never allow your amplifier to be driven into clipping Otherwise the speakers may be damaged 9 When using an amplifier with a rated output power higher than the nominal input power of the speakers care should be taken not to exceed the maximum input of the speakers 10 Do not attempt to clean the speakers with chemical solvents as this might damage the finish Use a clean dry cloth 11 Do not attempt to modify or fix the speakers Contact qualified Yamaha service personnel when service is needed The cabinet should never be opened for any reason 12 Be sure to read the Troubleshooting section regarding common operating errors before concluding that the speakers are faulty 13 Secure placement or installation is the owner s responsibility Yamaha is not liable for accidents caused by improper placement or installation of speakers For NS SW20 WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE 10 11 12 13 14 15 Do not operate this unit upside down It may overheat possibly causing damage Do not use excessive force on switches controls or connection wires When moving this unit first disconnect the power plug and
17. urning the product for repair 3 Misuse including but not limited to a failure to use the product for its normal purpose or in accordance with Yamaha s instructions on the proper use maintenance and storage and b installation or use of the product in a manner inconsistent with the technical or safety standards in force in the country where it is used 4 Accidents lightning water fire improper ventilation battery leakage or any cause beyond Yamaha s control 5 Defects of the system into which this product is incorporated and or incompatibility with third party products 6 Use of a product imported into the EEA and or Switzerland not by Yamaha where that product does not conform to the technical or safety standards of the country of use and or to the standard specification of a product sold by Yamaha in the EEA and or Switzerland Nn Where the guarantee differs between the country of purchase and the country of use of the product the guarantee of the country of use shall apply 6 Yamaha may not be held responsible for any losses or damages whether direct consequential or otherwise save for the repair or replacement of the product 7 Please backup any custom settings or data as Yamaha may not be held responsible for any alteration or loss to such settings or data 8 This guarantee does not affect the consumer s statutory rights under applicable national laws in force or the consumer s rights against the dealer

Download Pdf Manuals

image

Related Search

Related Contents

Copyright © All rights reserved.
Failed to retrieve file