Epson L90P - TM Two-color Thermal Line Printer User`s manual
Contents
1. 10 TM L90 with Peeler User s Manual 3 Slide the roll paper spacer to the appropriate width as shown above You can use the measurement printed inside the printer aligning the inside edge of the spacer with the desired measurement Width note When you want to set the roll paper width from 61 mm to 70 mm break off by hand the two tabs of the spacer shown in the illustration You can still also use widths from 35 mm to 60 mm with the spacer with the tabs broken off tabs 4 Insert the screw included with the spacer into the hole indicated in the illustration to the right and tighten it Even if you can see two holes this is the only one to put the screw in _ Fa hole for screw a Connecting Cables To connect cables first remove the bottom of the cover as shown in the illustration TM L90 with Peeler User s Manual 11 To place cables first break off by hand any of the three portions indicated by circles in the illustration the other portion is on the right Then put the cables through the holes and replace the bottom of the cover Cover Operation Label If you use the cover operation label included in the package attach it in one of the following locations a Side of the operation panel b Beside the power switch c Side of the printer 12 TM L90 with Peeler User s Manual2. IEC 61000 4 4 IEC 61000 4 5 IEC 61000 4 6 IEC 61000 4 11 FCC Compliance Statement For American Users This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense For Canadian Users This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme a la norme NMB 003 du Canada Safety Precautions This section presents important information intended to ensure safe and effective use of this product Please read this section carefully and store it in an accessible location N WARNING Shut down your equipment immediately if if produces smoke a strange odor or unusual noise Continued use may lead fo fire Immediately unplug the equipment and contact your dealer or a Seiko Epson service center for advice Never attempt to repair this product yourself Improper repair work can be dangerous
3. The thermal head is hot A CAUTION Be careful not to injure your hands on the manual cutter when installing roll paper Control Panel LEDs and Button POWER LED Is on when the power is on and is off when the power is off ERROR LED Is on when the printer is offline and is off when the printer is online It flashes when an error occurs PAPER OUT LED Comes on when roll paper is used up or not installed When roll paper is being installed it starts flashing when the first label comes out after the roll paper cover is closed and goes off when the PAPER FEED button is pressed When the printer is issuing labels it starts flashing when a label is issued and goes off when the issued label is removed from the peeler It also flashes when the printer is in a wait status for the FEED button to be pressed FEED button Feeds the roll paper TM L90 with Peeler User s Manual 3 Power Switch and Power Switch Cover The power switch is on the top left of the printer Press it to turn on the printer and press and hold it for more than 3 seconds to turn off the printer Power Switch Cover You can use the enclosed power switch cover to make sure that the power switch is not accidentally pressed Peel off the backing tape and press the cover into place to install it Zh WARNING If an accident occurs when the power switch cover shown to the right is attached immediately remove the bottom cover and unplug the power supply
4. 9x17 24x 24 12x 24 12x72 9x 51 Japanese When paper width is 80 mm 12 x 24 10 x 24 8x16 48 57 72 24 28 36 24 x 24 20 x 24 16x 16 Printwidth 72 mm 576 dot positions receipt roll paper with 80 mm width Character size Models except for Font A 12 x 24 W x H Japanese 1 50 x 3 0mm 1 5 x 6 0 mm 3 0 x 3 0 mm 3 0 x 6 0 mm Font B 9 x 17 Normal double high 1 13 x 2 13 mm 1 13 x 4 25 mm 2 25 x 2 13 mm 2 25 x 4 25 mm double width quadruple Kanji font A 24 x 24 3 0 x 3 0mm 3 0 x 6 0 mm 6 0 x 3 0mm 6 0 x 6 0 mm Japanese Font A 12 x 24 1 50 x 3 0 mm 1 50 x 6 0 mm 3 0 x 3 0 mm 3 0 x 6 0 mm Normal double high Font B 10 x 24 double width quadruple 1 25 x 3 0mm 1 25 x 6 0mm 2 5 x 3 0mm 2 5 x 6 0 mm Font C 8 x 16 1 0 x 2 0mm 1 0 x 4 0mm 2 0 x 2 0 mm 2 0 x 4 0 mm Kanji Font A 24 x 24 3 0 x 3 0mm 3 0 x 6 0 mm 6 0 x 3 0 mm 6 0 x 6 0 mm Kanji Font B 20 x 24 2 5 x 3 0mm 2 5 x 6 0mm 5 0 x 3 0mm 5 0 x 6 0 mm Kanji Font C 16 x 16 2 0 x 2 0mm 2 0 x 4 0mm 4 0 x 2 0 mm 4 0 x 4 0 mm Character sets 95 alphanumeric 37 international characters 128 x 11 graphic Japanese JIS JISX0208 1990 6879 characters soecial characters 845 characters Print speed Normal Maximum 120 mm s 120 mm s or less with the label peeler issuing mode High speed Maximum 150 mm s Ladder bar code two dimension bar code printing Maximum 90 mm s Two color printing Maximum 90
5. Never disassemble or modify this product Tampering with this product may result in injury or fire Be sure to use the specified power source Connection to an improper power source may cause fire Do not allow foreign matter to fall into the equipment Penetration by foreign objects may lead fo fire If water or other liquid spills into this equipment unplug the power cord immediately and then contact your dealer or a Seiko Epson service center for advice Continued usage may lead fo fire 2 TM L90 with Peeler User s Manual Zh CAUTION Do not connect cables in ways other than those mentioned in this manual Different connections may cause equipment damage and burning Be sure TO set this equipment on a firm stable horizontal surface The product may break or cause injury if it falls Do not use in locations subject to high humidity or dust levels Excessive humidity and dust may cause equipment damage or fire Do not place heavy objects on top of this product Never stand or lean on this product Equipment may fall or collapse causing breakage and possible injury To ensure safety unplug this product before leaving it unused for an extended period Do not use aerosol sprayers containing flammable gas inside or around this product Doing so may cause fire Caution Labels A WARNING Do not connect a telephone line to the drawer kick ouf connector otherwise the printer and the telephone line may be damaged A A CAUTION
6. TM L9O with Peeler Users Manual 208 l Bedienungsanleitung 13 Gebruikershandleiding 21 Manuel de lufilisateur 29 Manual do ufilizador 37 Manual del usuario 45 Manuale dell utente 53 405230503 Printer Parts 5 Power switch _____y 6 peeler open lever 7 cover open lever 8 control panel DIP Switch Tables Serial interface DIP switch 1 sw Function on o Power switch function Disabled Enabled 1 2 Interface condition By DIP switch By memory selection switch Handshaking XON XOFF DTR DSR Parity check Enabled Disabled Transmission soeed See table below 1 8 Transmission speed Transmission speed bps bits per second 1 7 1 8 19200 bps bits per second Serial interface DIP switch 2 sw Function Jon 4 cutter cover 3 label peeler detector 2 peeler cover 1 roll paper cover Parallel interface DIP switch 1 Sw Function Jon o H e fems TE 4 fesen TE r fesen TE Parallel interface DIP switch 2 w racion on OFF TM L90 with Peeler Specifications Font A 12 x 24 Font B 9 x 17 except for Japanese 10 x 24 Font C 8 x 16 only for Japanese Kanji font A 24 x 24 Kanji font B C 20 x 24 16 x 16 Both fonts are only for Japanese Columns Models except for When paper width is 80 mm Japanese 48 64 24 48 64 12x 24
7. bels issued depends on the length of the label but 2 labels are issued when the length of the label is less than 50 mm 2 and 1 label is issued when it is 50 mm 2 or more 7 After the paper is automatically fed and the first label comes out the PAPER OUT LED starts flashing 6 TM L90 with Peeler User s Manual 8 When using the label continuous issuing mode not using the peeler close the peeler cover now When using the peeler the label peeler issuing mode pass the paper through the peeler and close the peeler cover i p ea Fec Wi label peeler issuing mode label continuous issuing mode 9 Press the PAPER FEED button The paper is automatically fed backward and the PAPER OUT LED goes off Note If you open the roll paper cover with roll paper installed make sure to open the peeler cover first and then the roll paper cover If you open them in the reverse order the roll paper can get trapped under the roll paper cover when it is closed causing a possible paper jam When closing the roll paper cover make sure to close it firmly pressing both ends While a label is being issued do not touch it until the PAPER OUT LED starts flashing Pulling it before that may result in the waste of a label Do not block the label peeler detector with your fingers or anything else while the label issuing is in progress This may cause the printer to feed the following label TM L90 with Peeler User s Manua
8. cable to avoid a fire hazard Unpacking The following items are included for the standard specification printer If any items are damaged contact your dealer Printer Label roll paper Power switch cover Roll paper spacer Screw for installation of roll paper spacer Cover operation label Downloading Drivers Utilities and Manuals Drivers utilities and manuals can be downloaded from one of the following URLs For customers in North America go to the following web site http www epsonexpert com and follow the on screen instructions U U U UC U L For customers in other countries go to the following web site http www epson pos com Select the product name from the Select any product pulldown menu Installing the Printer Whether you are going to use the printer in the label peeler issuing mode or label continuous issuing mode not using the peeler you must install this printer vertically with the paper exit at the front See the illustration at the top of page 5 You can install it either on a flat surface or you can hang it on a wall by using the optional bracket WH 10 If the paper exit is blocked by label backing paper accumulating on a table or other surface a paper jam or other problem may occur Install the printer in a location such as at the edge of a counter where the backing paper will not accumulate near the paper exit 4 TM L90 with Peeler User s Manual A CAUTION Never in
9. e U S failure to strictly comply with Seiko Epson Corporation s operating and maintenance instructions Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation EPSON and ESC POS are registered trademarks of Seiko Epson Corporation in the U S and other countries NOTICE The contents of this manual are subject to change without notice 2004 by Seiko Epson Corporation Nagano Japan EMC and Safety Standards Applied Product Name TM L90 with Peeler Model Name M165C The following standards are applied only to the printers that are so labeled EMC is tested using the Epson power supplies Europe CE marking Safety EN 60950 North America EMI FCC ICES 003 Class A Safety UL 60950 CSA C22 2 No 60950 Japan EMI VCCI Class A Oceania EMC AS NZS 3548 CISPR22 Class B TM L90 with Peeler User s Manual 1 WARNING The connection of a non shielded printer interface cable to this printer will invalidate the EMC standards of this device You are cautioned that changes or modifications not expressly approved by Seiko Epson Corporation could void your authority to operate the equipment CE Marking The printer conforms to the following Directives and Norms Directive 89 336 EEC EN 55022 Class B EN 55024 IEC 61000 4 2 IEC 61000 4 3
10. ff the printer open the peeler cover and then the roll paper cover 2 Clean the thermal element of the print head with a cotton swab lightly moistened with an alcohol solvent ethanol methanol or IPA as shown in the illustration 3 Close the roll paper cover after the alcohol solvent has dried 8 TM L90 with Peeler User s Manual Cleaning the Platen Roller Roll Paper End Sensor When paper dust accumulates on the platen roller or the roll paper end sensor follow the steps below to clean them To maintain good functional capabilities clean them regularly every 6 months 1 Turn off the printer open the peeler cover and then the roll paper cover 2 Clean the platen roller and roll paper end sensor with a cotton swab lightly moistened with water or an alcohol as shown in the illustration RRR R z S E B C F L an jpm w P lt 3 Close the roll paper cover after the water or alcohol has dried Cleaning the Peeler Unit After the peeler is used for a prolonged period of time the glue from the labels accumulates on the rollers of the peeler unit If you leave the rollers in such a condition the glue may stick to issued labels or a paper jam may occur To prevent malfunctions and maintain good print quality clean the rollers regularly every 100 000 labels You can clean them easily if you use a wasted label as shown in the illustration Note Do not use any alcohol based solvents for cleanin
11. g Such solvents may enter the roller shaft and cause a malfunction of the peeler TM L90 with Peeler User s Manual 9 Using Different Paper Widths Be sure to set the paper width with the memory switch to match printing to the print width For detailed information on the memory switch see the TM L90 with Peeler Technical Reference Guide Also do not increase the paper width after you have used a narrower width For example do not use 60 mm 2 36 and then change to 80 mm 3 15 The reason not to increase the width setting if the printer has ever been used is that when narrow paper is used part of the head contacts the platen Therefore when a wider setting is used part of the head or the cutter blade may be worn out which can cause poor printing The TM L90 accommodates 80 mm wide roll paper with no adjustments For rolls from 38 mm to 70 mm wide you use the spacer included with the printer Rolls from 71 mm to 79 mm cannot be specified If the rolls are from 61 to 70 mm wide you break two tabs off the spacer See the width note on page 11 1 Insert the roll paper spacer so that the front edge goes through the notch and down to the shaft as shown below notch a roll paper spacer front edge 7 L i T i 2 Push the roll paper spacer until you feel it click onto the shaft Note Check that the roll paper spacer slides smoothly to the left and right U E inside edge of the spacer shaft
12. l 7 Zh CAUTION When installing roll paper be careful not fo injure your hands on the manual cutter Troubleshooting ERROR LED is on or flashing L Make sure that the roll paper cover is closed and the PAPER OUT LED is not on Close the cover or replace the paper if necessary J Ifthe printer has been printing a lot and the print head gets too hot the ERROR LED starts flashing and printing stops When its temperature cools down to the normal range printing resumes automatically L1 Turn off the printer and then turn it back on If the LED is still flashing consult with your supervisor or a service person PAPER OUT LED is flashing If the PAPER OUT LED continues to flash even after the issued label is removed the label peeler detector may be detecting something Press the PAPER FEED button once Paper jam Turn off the power open the peeler cover and then open the roll paper cover to check for a paper jam If there is a paper jam remove the jammed paper and follow the instructions in the Installing Roll Paper section to prepare the printer for printing Cleaning the Thermal Head AA CAUTION After printing the thermal head can be very hot Be careful not to touch it and to let it cool before you clean it Do not damage the thermal head by touching it with your fingers or any hard object Epson recommends cleaning the thermal head periodically generally every 6 months to maintain receipt print quality 1 Turn o
13. mm s Paper dimensions 80 mm 79 5 0 5 x max diameter 90 mm 60 mm 59 5 0 5 x max diameter 90 mm 58 mm 57 5 0 5 x max diameter 90 mm Thermal paper type Roll paper Monochrome ENTPD ENTPE Two color ENTPC Label paper Monochrome ENTLA series Two color ENTLB series Interface RS 232C IEEE 1284 compatible Operating 5 to 45 C Storage 10 to 50 C Approximately 1 9 kg lps lines per second dpi dots per 25 4 mm dots per inch iii iV TN L90 with Peeler User s Manual All rights reserved No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of Seiko Epson Corporation No patent liability is assumed with respect to the use of the information contained herein While every precaution has been taken in the preparation of this book Seiko Epson Corporation assumes no responsibility for errors or omissions Neither is any liability assumed for damages resulting from the use of the information contained herein Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages losses costs or expenses incurred by purchaser or third parties as a result of accident misuse or abuse of this product or unauthorized modifications repairs or alterations to this product or excluding th
14. stall the printer in locations that receive direct sunlight The diffuse reflection from the roll paper may cause the label peeler detector to malfunction When a malfunction occurs the PAPER OUT LED starts flashing Press the FEED button fo resume using the printer Note To hang the printer on the wall see the Wall Hanging Bracket Set Installation Manual provided with the WH 10 for instructions Installing Roll Paper Note Be sure to use roll paper that meets the specifications 1 Make sure that the power is on 2 Pull the peeler open lever forward and open the peeler cover See the illustration on the left below 3 Pull the roll paper cover open lever forward and open the roll paper cover See the illustration on the right below 4 TM L90 with Peeler User s Manual 5 5 Make sure that the mode switch is set to the mode you are going to use To the right for the label peeler issuing mode or to the left for the label continuous issuing mode Left label continuous Right label peeler issuing mode issuing Mode Epa D k i naa iaiia i X 9 6 Pull out the paper until the end exactly reaches the guideline indicated with arrows shown in the illustration below Eliminate any slack in the roll paper and then close the roll paper cover Note Making sure the paper end is at the guideline reduces the number of labels required for detecting the minimum paper length The number of la
Download Pdf Manuals
Related Search