820 Blenheim & Seattle LED installer and owner
Contents
1. 3 Have a problem that is different to those in the previous examples 1 3 For general advice about your heater call Valor Fires TECHNICAL HELPLINE 0844 8711 565 CALLERS IN THE REPUBLIC OF IRELAND Call 0044 844 8711 565 What should I do when I m ready to dispose of my heater The plug should be removed from the mains cable and the mains cable cut from the heater These should be disposed of with the heater Environmental Protection Waste electrical products should not be disposed of with household waste Please recycle where facilities exist Check with your local authority or retailer for recycling advice aa Baxi Heating U K Limited 2010 Page 15 INSTALLER AND OWNER GUIDE 6 WARRANTY AND SERVICE Information for the customer Standard Warranty Terms amp Conditions The warranty is for 12 months subject to contract In the United Kingdom servicing can be carried out either by a heateam service engineer or a suitably qualified person You must register your heater with heateam the service division of Baxi Heating UK Limited either by completing and returning the registration card or calling our free telephone registration line on 0800 032 72 44 Our promise to you If you experience a fault with your new heater we aim to provide a safe and high quality repair service supported by our dedicated national network of highly skilled engineers Nothing in this warranty will affect your statutory rights Wha2. 9 Locating the cable Baxi Heating U K Limited 2010 Page 11 INSTALLER AND OWNER GUIDE Fitting the heater 1 Locate the spacer frame and heater over the screw heads ensuring a tight fit If the fit is loose remove the spacer frame and heater from the wall Tighten the wall screws slightly and reposition the spacer frame and heater Fitting the light diffuser 1 There is a light diffuser supplied with the heater See figure 3 Place this on to the metal flange below the plastic screen See figure 10 Fitting the Fascia Blenheim model 1 Removing the fascia trim may have moved the magnets used to fix it to the heater The magnets should be located as in figure 11 2 Locate the fascia onto the heater Ensure that the sides of the fascia sit on the floor hearth 3 There are two hanging screws on the rear of the firefront Locate these into the slots as in figure 12 4 Place the one piece fuel effect on top of the firefront fuel support Figure 12 Firefront location Baxi Heating U K Limited 2010 Page 12 INSTALLER AND OWNER GUIDE Seattle model 1 With the fascia trim removed unscrew and remove the two screws from the lower right hand side of the heater See figure 13 then align the four holes in the firefront assembly with those on the heater See figure 14 Secure with the two screws removed previously and two screws supplied 2 Removing the fascia trim may have moved th
3. Spacer Frame The optional spacer frame is for use during installations where a chimney recess or rebated fire surround are not available For your safety the frame and heater must be securely fixed to the rear wall Fitting the spacer frame The rear of the spacer has two screw location slots in the top flange These should be to the rear when fitting 1 Position the spacer frame against the wall Ensure that the spacer frame is central to the fireplace 2 The top rear flange of the spacer frame has two screw locations Mark the positions of the Screw location points a screw locations on the rear wall See figure Figure 8 Location points 3 Remove the spacer frame from the fireplace and place away from the work area 4 Drill the screw locations using a suitably sized masonry drill bit for the wall plugs supplied 5 Insert two wall plugs provided into the holes 6 Insert a wood screw into each hole and screw in until there is approximately 6mm of screw protruding from the wall Preparing the heater for installation 1 Ensure that the decorative front surround has been removed from the heater as described earlier in this guide 2 Using the four No 8 x 3 8 screws provided fix the heater to the spacer frame 3 There is a supply cable slot on both sides of the spacer frame It is located at the base Decide which side to pass the supply cable through and position the supply cable in the spacer frame slot See figure 9 Figure
4. UNPACKING Before continuing any further with the installation of this heater please read the following Important safety instructions e The approximate lifting weights kg of the heater parts are listed below Model Heat engine Firefront Fascia Spacer Fuel effect Blenheim 5 44 4 58 0 63 1 3 0 72 Seattle 5 44 0 91 0 63 1 3 0 9 An optional spacer frame kit is obtainable either from the your heater supplier or direct from Valor Fires Sales The kit is a 75mm 3 inch spacer kit Kit number 05801T1 One person should be sufficient to lift the heater If for any reason this weight is considered too heavy then obtain assistance When lifting always keep your back straight Bend your legs and not your back Avoid twisting at the waist It is better to reposition your feet Avoid upper body top heavy bending Always bend from the knees rather than the waist Do not lean forward or sideways whilst handling the heater Always grip with the palm of the hand Do not use the tips of fingers for support Always keep the heater as close to the body as possible This will minimise the cantilever action Use gloves to provide additional grip Always use assistance if required Baxi Heating U K Limited 2010 INSTALLER AND OWNER GUIDE 2 SAFETY This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given
5. supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance Always Always install the heater in accordance with this guide If in doubt obtain expert advice Always make sure the electrical socket is accessible and located adjacent to but not above the heater Always disconnect the heater from the electrical supply before carrying out cleaning or maintenance Always make sure the heater is firmly secured to prevent it from being tipped over Always use a fireguard when young children infirm persons and pet animals can come into contact with the heater Always use genuine Valor Fires spare parts Never Never leave children unsupervised in a room where the heater is ON and unguarded Never obstruct or cover the fan outlet or force items into heater openings Never install or use the heater anywhere where water is in use i e Bathrooms Kitchens Shower Rooms Swimming Pools etc Never use aerosols or steam cleaners on or around the heater Never route the electric supply cable under carpet etc Never install the heater close to curtains or combustible materials Never use the heater to dry clothes etc Never sit or stand on the heater Never use the heater with a timer switch or similar device Important electrical safety The heater must not be located in front of or under an electrical socket the
6. the top of the heater there are four small holes two each side of the heater See figure 7 Item 1 From the front of the heater thread about 50mm 2 inches of the steel wire into the inside small hole on the left side of the heater See figure 7 item 2 8 Thread the other end of the wire through the remaining small hole on the left hand side of the heater Continue to push the wire through this re hole until there is only a small loop of Figure 7 Steel wire fixing Detail at top of wire at the front of the heater See heater may differ from that shown figure 7 item 3 Baxi Heating U K Limited 2010 Page 10 INSTALLER AND OWNER GUIDE 9 At the back of the heater there will be a long piece and a short piece of wire coming through the two holes Hold the short piece and give the long piece a gentle tug This will secure the steel wire Take the long piece and thread this through the eyescrew in the back of the fireplace opening See figure 7 item 4 10 From the back of the heater thread the long piece of steel wire through the outer small hole on the right hand side of the heater See figure 7 item 5 11 Locate the heater in the fireplace opening then from the front of the heater gently pull the steel wire on the right hand side to gather up the excess until the heater is secure Thread the wire through the remaining small hole to lock the wire and heater in place See figure 7 item 6 Method C
7. to a copyright work may be liable to criminal prosecution and civil claims for damages CUSTOMER CARE Thank you for choosing Valor Fires All Valor Fires heaters are designed to meet the most stringent quality performance and safety requirements to provide our customers with many years of trouble free service This guide aims to improve your understanding and appreciation of your new Valor Fires heater by providing simple and informative instructions to enable you to install it and to ensure that you benefit from the excellent performance and features it has to offer If you require further assistance the Valor Fires Technical Helpline will be pleased to help Please telephone 0844 8711 565 local rates apply in the United Kingdom In the Republic of Ireland please telephone 0044 844 8711 565 VAL R FIRES Valor Fires Erdington Birmingham B24 9QP www firesandstoves co uk Because our policy is one of constant development and improvement details may vary slightly from those given in this publication Baxi Heating U K Limited 2010 INSTALLER AND OWNER GUIDE Safety First Valor Fires heaters are CE Approved and designed to meet the appropriate British Standards and Safety Marks CE Quality and Excellence All Valor Fires heaters are manufactured to the highest standards of quality and excellence and are manufactured under a BS EN ISO 9001 quality system accepted by the British Standards Institute 1 HANDLING AND
8. 5133239 02 VAL R FIRES Model 820 Electric Heater Fitted with one of the following fascia Blenheim Seattle C GC No EF 032 33 This guide is intended to help you install and care for your Valor Fires electric heater Please read carefully before installing and using your heater However if further information is required our Valor Fires Technical Helpline will be pleased to help Telephone 0844 8711 565 National call rates apply in the United Kingdom In the Republic of Ireland Telephone 0044 844 8711 565 m _ BAXI VALOR WONDERFIRE Important Please keep your guide in a safe place for future reference Baxi Heating U K Limited 2010 INSTALLER AND OWNER GUIDE Baxi Heating U K Limited 2010 All rights reserved No part of this publication may be reproduced in any material form including photocopying stored in any medium by electronic means including in any retrieval system or database or transmitted in any form or by any means whether electronic mechanical recording or otherwise without the prior written permission of the copyright owner Applications for the copyright owner s permission to reproduce any part of this publication should be made giving details of the proposed use to the following address The Company Secretary Baxi Heating UK Limited The Wyvern Business Park Stanier Way Derby DE21 6BF Warning Any person who does any unauthorised act in relation
9. e is on the outer edge of the base See figure 1 Item 1 2 To remove the cable guide push and lift the tab on the bottom The bottom of the cable guide will open See figure 1 Item 2 3 Lift the electric cable clear of the cable guide Baxi Heating U K Limited 2010 INSTALLER AND OWNER GUIDE 4 Hold the bottom of the cable guide close to the heater then gently pull the cable guide away from the rectangular slot See figure 1 Item 3 Fitting the cable guide When fitting the cable guide please remember that the wider part of the cable guide has to be fitted against the outer edge of the base See figure 1 Item 1 1 Gently pinch the sides of the cable guide See figure 1 Item 4 and push the cable guide into the required rectangular slot 2 Place the electrical cable into the guide and close the top of the cable guide 7 Cable Guide Removing the fascia 1 Very strong magnets attach the fascia to the heater Support the rear of the heater and gently pull the fascia forward See figure 2 2 Keep the fascia in a safe place while installing the heater Figure 2 Removing the fascia Baxi Heating U K Limited 2010 INSTALLER AND OWNER GUIDE Heater fixing All fixings supplied with the heater have been identified in figure 3 Quantity Illustrations are not to scale Wall plug No 8 x 3 8 Screw M4 x 25mm Screw Control Knob Figure 3 Contents Fascia not sho
10. e magnets used to fix it to the heater The magnets should be located as in figure 11 3 Place the one piece fuel effect on top of the firefront fuel support Baxi Heating U K Limited 2010 Page 13 INSTALLER AND OWNER GUIDE 4 USING THE HEATER Important Safety Never cover the heater or obstruct the openings at the base of the heater this could cause overheating and consequent risk of fire Operation switches Variable energy control nano Figure 15 Controls What are the three switches for The heater is operated by three switches located below the hood on the left hand side of the heater ls Switch 1 ae Switch 2 D Switch 3 What is the knob for Main On Off In the ON position only the flame effect operates 1kW fan heat setting and flame effect Switch 1 needs to be in the ON position to enable switch 2 to operate 2kW fan heat setting and flame effect Switches 1 amp 2 need to be in the ON position to enable switch 3 to operate The heater has a variable energy control located below the hood on the right hand side of the heater The variable energy control will only work when all three switches are on If the room requires maximum heat rotate the control fully clockwise For less heat rotate the control counterclockwise until the required heat setting is achieved When operating the variable energy control will operate betwe
11. en the 1kW and 2kW settings Turning the knob fully counterclockwise will switch the variable energy function off Baxi Heating U K Limited 2010 Page 14 INSTALLER AND OWNER GUIDE 5 CLEANING AND MAINTAINING THE HEATER How do clean my heater The heater fascia and plastic parts need only to be wiped clean with a dry soft cloth do not use polishes or abrasive materials The Seattle heater may have fingerprints on the fascia surface These can be removed by applying a small amount of baby oil to a lint free non abrasive cloth and wiping the surface Use a clean cloth to remove the oil have a problem with my heater Important Safety Before undertaking maintenance always disconnect the heater from the electricity supply by removing the 3 pin plug and allowing the heater to cool completely 1 My heater is on but there is no light or heat The first thing to do is check the wall socket To do this plug in a known working appliance If the appliance you have plugged in works then there is a good chance that the problem lies with the 13 Amp fuse in the heater plug If either fuse or socket is suspected have them checked by an electrician 2 My heater is on but there is no heat A cut out device is fitted to the heater to prevent damage due to over heating If it operates due to an obstruction in the airflow the heater must be turned off and allowed to cool for 15 minutes and the obstruction removed before restarting
12. es e g loss of earnings business losses stress and inconvenience arising from a production breakdown including repair delays caused by factors outside our reasonable control Baxi Heating U K Limited 2010 Page 17 INSTALLER AND OWNER GUIDE Baxi Heating U K Limited 2010 Page 18 INSTALLER AND OWNER GUIDE To be completed by the customer Model 8112110 Serial number Can be found on the information label See figure 16 CNE EE ALABEL CONTAINING THE SERIAL NUMBER MAY HAVE BEEN PLACED INSIDE THIS BOX Fascia name Block Capitals Be eee ee EEE ee EN El Fascia code Can be found close to the information label Block Capitals ee A A LABEL CONTAINING THE FASCIA CODE MAY HAVE BEEN PLACED INSIDE THIS BOX Brand Please tick Baxi Valor Wonderfire Other Date of Installation z R n Information a M M location Figure 16 Baxi Heating U K Limited 2010 Page 19 VAL R FIRES Baxi Heating U K Limited 2010
13. g with the installation of this heater please ensure that you have completed the information on the last page of this guide Do I need any tools 1 Depending upon the chosen method of installation you may need the following screwdrivers e A Pozidrive Phillips cross head This should have a number 2 size tip e A Flat end 2 If drilling into brickwork you will need a power drill preferably with hammer action and appropriate size drill bit for the wall plugs supplied Where can fit the heater This heater can be fitted into fireplaces or surrounds where the following dimensions are available Width 400mm 450 mm 15 35 inches 17 72 inches Height 555mm 590 mm 21 9 inches 23 2 inches Depth At least 75mm At least 3 inches An optional spacer frame kit is obtainable either from the your heater supplier or direct from Valor Fires Sales The kit is a 75mm 3 inch spacer kit Kit number 05801T1 Moving the cable guide At the base of the heater you will find an electric cable which runs through a rectangular plastic cable guide As supplied the cable guide is fitted into the rectangular cut out on the right side of the heater If required the cable guide can be removed and put in the rectangular slot in the centre or left hand side of the heater For removal and fitting please see the following sections Removing the cable guide 1 Before removing the cable guide please note that the wider part of the cable guid
14. may result in the marble cracking 1 Place the heater into the fireplace or surround opening Make sure that the heater is in the middle of the surround or fireplace 2 There are two slotted holes in the top of the heater See figure 5 Mark through the slotted holes so that their position is clear when the heater is removed 3 Remove the heater 4 Drill an appropriate size hole in each of the Figure 5 Slots for screw fixing Baxi Heating U K Limited 2010 INSTALLER AND OWNER GUIDE marked positions Insert wall plugs into the drilled holes 5 Place the heater so that the slotted holes are in line with the wall plugs in the fixing surface 6 Screw and secure the heater with two wood screws See figure 3 533 560mm Method B Wire fix 21 22 inches This method of fixing needs a fireplace opening and is recommended when fixing the heater to a marble surround or where the wall or brickwork is in poor condition 1 The fixing kit supplied with the heater includes a steel wire and eyescrew See figure 3 These fireplace opening 2 Mark the eyescrew position on the centre line at the back of the fireplace Opening and at a height of 533 560mm 21 inches 22 inches See figure 6 3 Drill an appropriate size hole in the marked position 4 Insert a wall plug into the drilled hole 5 Screw the eyescrew into the wall plug 6 Position the heater in front of the fireplace opening 7 At
15. socket must always be accessible in order to disconnect the heater from the electrical supply for maintenance and cleaning Baxi Heating U K Limited 2010 INSTALLER AND OWNER GUIDE CAUTION In order to avoid a hazard due to inadvertent resetting of the thermal cut out this appliance must not be supplied through an external switching device such as a timer or connected to a circuit that is regularly switched on and off by the utility Important This heater must be earthed e The heater is supplied with a 3 pin 13 Amp fused re wireable plug with 1mm 3 core cable e The wires in the cable are coloured in accordance with the following code Live Brown Neutral Blue Earth Green Yellow e The electric cable must be safely routed from the heater to an electrical socket If the electric cable is damaged to avoid a hazard it must be replaced by a Valor Fires authorised service agent or similarly qualified person See the last page of this guide for useful telephone numbers All external wiring between the heater and the electrical supply shall comply with current IEE regulations Extension leads should not be used Baxi Heating U K Limited 2010 INSTALLER AND OWNER GUIDE 3 FITTING THE HEATER The installation of this heater requires a reasonable level of DIY skills Please read this guide thoroughly before commencing installation and if in doubt seek help from a competent person Important Before continuin
16. t you need to do if you experience a problem with the operation of the heater Read section 5 of this guide Cleaning and maintaining the heater If the problem cannot be resolved simply call our service division heateam on 0844 8711 565 to book an engineer visit or for any general advice that you may need Our contact centre is open Monday to Friday 8am 6pm weekends and Bank Holidays 8 30am 2pm excluding Christmas Day and New Years day When calling heateam it would be helpful if you could have the following information to hand Heater serial number Heater brand and model number Date of installation Proof of purchase If you do not have the heater serial number Note Details 1 3 can be found on the last page of this guide Rag Ne What this warranty covers Free of charge repair or replacement of components found to be of faulty manufacture Free of charge replacement of the complete unit providing the failure is related to a manufacturing fault that cannot be repaired or is uneconomic to repair Baxi Heating U K Limited 2010 Page 16 INSTALLER AND OWNER GUIDE What this warranty does not cover Repairs to heaters which haven t been installed properly and as set out in this guide Faults caused by inadequate supply of electricity Reimbursement of any third party repair or replacement costs that we haven t been told about or agreed with you in advance Compensation or consequential loss
17. wn Items are not to scale 5 4 4 2 2 1 1 1 1 1 Baxi Heating U K Limited 2010 INSTALLER AND OWNER GUIDE Fitting the Control Knob The control knob is supplied separately with the accessory pack Fit the control knob before continuing with the heater installation To assemble the control knob to the control spindle firstly line up the D profile on the underside of the control knob to the D profile on the spindle both flats should line up Place the control knob onto the spindle and gently push until the control knob is fully located Figure 4 The heater must be fixed into position to prevent it from being tipped over The following fixing options are available e Screw Fixing e Wire Fixing e Spacer Frame An optional spacer frame kit is obtainable either from the your heater supplier or direct from Valor Fires Sales The kit is a 75mm 3 inch spacer kit Kit number 05801T1 If fitting the heater into a fireplace or surround opening try the heater in the opening to ensure that it will fit If fitting the heater onto a decorative hearth surface such as marble or tile it is advisable to protect the hearth surface Do not drag the heater across the surface of the hearth as this may scratch the hearth surface Method A Screw fixing Note If fixing to marble it is recommended that Method B Wire fixing is used Drilling marble without the correct tools and experience
Download Pdf Manuals
Related Search