Home

Vivitek D751ST series Installation manual

image

Contents

1. Installation wall installation should be performed by specialists who have technical knowledge and ability Incomplete or improper installation may cause wall mounted bracket to fall resulting in personal injury or property damage Please install the wall mounted bracket according to this instruction Otherwise the wall mounted bracket may fall and result in personal injury or an accident Operating power cord with care Improper operation could cause fire or electric shock Please comply with the following requirements while operating 1 Do not operate the power plug when your hands are wet 2 Do not use damaged and changed power cord 3 Do not employ excessive force while pulling power cord when it passes through the wall mount bracket If the position of installation of the wall mounted bracket is prone to be affected by vibration and impact please do not install the wall mounted bracket Vibration and impact may damage the projector and the installation plate or even may result in the wall N mounted bracket and projector falling resulting injury of people and damage of property Talling the wall mount bracket please adopt methods that can support the projector and wall mount bracket as well as to eliminate any vibration from the horizontal level M8 nut and screw should be applied Nut and screw that are less than 8M may lead to hanger falling DELTA is disclaim from the responsible for any loss and damage caused by insufficie
2. 2 The position should be away from other electrical equipments such as fluorescent lamps and air condition Some fluorescent lamps may cause interference signal to the projector s remote control The length of connecting power cord should be less than 20 meters so as to reduce noise interference Plug in screen or flat screen is suggested When using interactive function please make sure to set the projector under the following condition 1 Projection screen is rectangle in shape with no distortion 2 The vertical and horizontal angle between projector and the projection screen should be less than 3 degree comparing to the projector screen 3 The horizontal and vertical keystone correction should be less than 5 degree while using keystone correction ABOUT THIS INSTALLATION INSTRUCTION This instruction introduces how to use customized wall mounted bracket to install D75 ultra short throw projector on walls The unit of measurement for all sizes mark place in this instruction is in mm Ch ee 1 PACKAGING ITEMS P 4 2 SPECIFICATIONS P 5 3 PROJECTION DISTANCE CHART Fil 4 INSTALLATION STEPS FOR WALL MOUNTED BRACKET P 9 Dismantle parts Verify the strength of walls installation environment installation position and drill holes on the walls Install hanger frame on walls Verify the distance of the projector Move the three axis fine tuner to proper position according to the projector distance
3. chart Power cord should pass through the hanger frame Adjust the slider plate up and down to align to the standard position Install the projector onto the hanger frame Connect the power cord and other electrical cables to the projector 5 ADJUSTING STEPS OF PROJECTOR IMAGE 1 Switch on the projector 2 Adjust the aspect ratio 3 Display the test image 4 Adjust the left and right alignment position 5 Adjust the up and down rotation 6 Adjust the left and right rotation 7 Adjust the keystone 8 Adjust the image Size 9 Adjust the image up and down 10 Switch off the testing image display HARDWARES INCLUDED FRAME 2 FRAME 1 il J ji HJ INT PART LIST D75X ULTRA SHORT SERIES BRACKET 1 SETTING DRILLING PAPER 1 1 H1 VERTICAL DISTANCE FRAME 3 9 TRI AXIS FINE TUNING COMPONENTS cre incl mm diagonal inch 1727 11 86 328 5 S mes _ inch po epee RSA ne 2159 11 59 3215 2210 11 82 327 4 IT MUST ALIGN CENTER OF SCREEN CENTRAL LINE WHEN INSTALLING D75X INSTALLATION FRAME 1 SETTING DRILLING PAPER 1 1 spring washer Screen shot Hardware Specifications Qty Purpose M4 10mm ball head cross head screw with flat 3 Used for connecting wall mounted bracket gasket and spring washer pcs structure 7 with projector j Ji M8 70mm setscrew with nut
4. flat gasket and 4 pcs Used for installing and fixing wall mounted IH bracket structure 1 onto the wall 1 Please follow the instructions in the manual and install with the attached hardwares 2 Please prepare the required tools and hardwares before installation SPECIFICATION Item Spec Description Gross mass of hanger frame About 4 72k The three axis fine tuning components 2 82kg wall fixture hardwares 0 86kg independent components packed seperately 0 12kg Maximum load capacity Not inclusive of wall mounted bracket s weight The left and right adjusting range Frame structure 3 adjustable by 30mm frame structure 7 adjustable by 10mm The up and down z Oey The three axis fine tuner does horizontal scrolling adjustment rotation adjusting range The left and right ak The three axis fine tuner does horizontal rotating adjustment rotation adjusting range Keystone adjusting range Forward and backward adjustment by range Up and down adjustment by range D75X INSTALLATION FRAME 1 SETTING DRILLING PAPER 1 1 59 The three axis fine tuner does vertical scrolling adjustment Can be adjusted 120mm forward 40mm D75X ULTRA SHORT SERIES BRACKET 1 SETTING DRILLING PAPER 1 1 4 X A 8 5 THREAD WITH DEPTH 60MM N O D751sTxGAOo 4s XGA N O D751sTxGAOo 4s 43 H1 Vertical distance mama mon mr 1727 11 86 328 5 1905 12 88 3
5. 54 4 1956 13 18 361 4 EEC NC s s 2032 13 60 372 6 a 2083 13 90 380 2 p N DrSswrwca0s 0 35 H1 Vertical distance a m 2032 11 02 307 2 2159 11 59 321 5 2210 11 82 327 4 EC E erjas Be jer eee es jew 1272 2502 F er osoa TE 100 H1 VERTICAL DISTANCE THE DISTANCE FROM PROJECTED SCREEN TO THIS PART CENTRAL LINE WHEN INSTALLING IT MUST ALIGN CENTER OF SCREEN Description 1 A is the drill location Please review the description in manual page 9 2 This screenshot is only for D751ST XGA 0 43 D WXGA 0 35 hanger 3 The scale in the screenshot for all indicated location is 1 1 SCREENSHOT OF PROJECT DISTANCE m M _ 27 2 H1 S PROJECT DISTANCE D751ST XGA 0 43 Screen size diagonal Screen width Screen height Projecting distance D Vertical distance H1 inch mm inch mm inch mm inch mm inch mm 68 1727 54 1382 40 1036 11 16 283 4 11 86 328 5 75 1905 59 1524 45 1143 13 83 351 4 12 88 354 4 77 1956 61 1565 46 1173 14 62 371 4 13 18 361 4 rose 0726 D755WT WXGA 0 35 Screen size diagonal Screen width Screen height Projecting distance D Vertical distance H1 inch mm inch mm inch mm inch mm inch mm 80 2032 67 1723 42 1077 11 11 282 3 11 02 307 2 85 2159 71 1831 45 1144 12 73 323 3 11 59 321 5 87 2210 73 1874 46 1171 13 40 340 3 11 82 32
6. 7 4 90 2286 76 1939 47 1212 14 38 365 3 12 16 336 1 92 2337 77 1982 48 1239 15 01 381 3 12 38 341 6 ASSEMBLY BREAKDOWN DIAGRAM Quick Installation Steps Step 1 frame 1 setting drilling paper of ultra short series 1 1 to the proper position in up screen see details please refer to P 9 Perforate the setting wall percussion drill and drill 8 5 60mm depth Step 2 Install M8 70 setscrew in the wall s hole Step 3 Use M8 70 setscrew 4X fix structure frame 1 to the wall s hole Step 4 Install structure frame 2 on structure frame 1 see P 10 switch it to intermediate position and use screw B M4 10 up and down adjusting fixing screw to lock it yet Step 5 Loosen screw C decline structure frame 3 by 5 degree to aim at the positioning peg and position the slider structure into structure frame 2 s slide way Adjust the slide way to intermediate position and tighten the screw C into structure frame 2 s threaded hole but do not lock it When the positioning is in place tighten the screw C see details please refer to P 11 Step 6 Use I screw to connect structure frame 7 and projector Fix them and install them on structure frame 6 After adjusting structure frame 7 to a proper position lock screw H see P 12 H 3 M4 10 BRACKET 7 TIGHTEN SCREW D 4 M4 10 PARALLEL C 2 M4 10 PARALLEL ADJUSTMENT FIXING SCREW STEP5 FRAME 3 ADJUSTMENT FI
7. XING SCREW G TRAPEZOID ADJUSTMENT NUT ROTATION ASIX F PARALLEL ADJUSTMENT FIXING SCREW E VERTICAL ROTATION L ki ADJUSTMENT FIXING ka NUT FRAME 5 FRAME 6 STEP6 FRAME 7 1 3 M4 10 PROJECTOR CONNECTION SCREW STEP6 FRAME 4 STEP5 FRAME 2 STEP4 M VERTICAL ROTATION ADJUSTMENT FIXING SCREW A 4 M8 70 SETSCREW STEP2 SETTING DRILLING PAPER OF ULTRA SHORT SERIES 1 1 TO THE PROPER POSITION IN UP SCREEN FRAME 1 STEP3 B 4 M4 10 VERTICAL ROTATION ADJUSTMENT FIXING SCREW STEP4 INSTALLING STEP 1 Installing steps of holder 1 1 2 3 Lg SCREENSHOT 1 Ss A 2 JSE SE je II ALIGN THE CENTRAL VERTICAL T LINE ON THE SCREEN N Ensure the projector image allies with the center line of the screen and determine the corresponding vertical distance value H1 according to the projector distance chart Use D79X setting perforating paper of ultra short throw series 1 1 to determine the corresponding vertical distance H2 H1 27 2mm Fix the D79X setting perforating paper of ultra short throw series 1 1 and drill the wall according to the hole position on paper see picture 1 Drive the attached setscrew 4 M8 70mm in the corresponding wall s hole Loosen screw B 4 M4 10 and dismantle the setting wall components structure frame 1 and structure frame 2 Install the structure frame 1 a
8. d bracket and then cause the projector to fall As a result personal injury or property loss may occur Please tighten all the nuts and screws after adjustment Otherwise the projector or hanger may fall and lead to personal injury or property lass Please refrain from loosening the nuts and screw after installation unless otherwise deemed necessary and performed by qualified specialists who have technical knowledge and ability Please test the wall mounted bracket at a regular interval to ensure the nuts and screw are tight If the nuts and screws are found loose please tighten them otherwise the projector or the wall mounted bracket may fall and cause personal injury and property loss N CAUTION Please do not install the hanger frame in places where the temperature could be higher than that the projector s maximum sustainable temperature because the exceeding high temperature may damage the projector Please avoid installing the wall mounted bracket in places that is too wet or too dusty so that lens and optical While adjusting wall mounted bracket please do not employ excessive force because the wall mounted bracket Only professional person can dismantle or reset the projector including maintaining and overhauling Please Q consult the relevant information as illustrated in the instructions THE LOCATION FOR WALL MOUNTED BRACKET Conducting power routing in advance in the position where the hanger frame is installed
9. e Pudong New Area Shanghai CIMIC building 18 F zip code 200120 Tel 86 21 58360088 Fax 86 21 58360099 http www vivitek com cn O Vivitek EMEA Zandsteen 15 2132MZ Hoofddorp The Netherlands Tel 31 20 655 0960 Fax 31 20 655 0999 E mail info vivitek eu Web www vivitek eu D79X ultra short series installation instructions 2nd Edition
10. ight rotation so that structure frame 7 can drive projector towards horizontal rotation Z axis direction 3 When the horizontal rotation position is adjusted to a proper position tighten the screw P 4 When the three axis are adjusted to proper positions tighten the rotation axis nut gt J N 5 TRI AXIS TIGHTEN SCREW V F PARALLEL ROTATION A TIGHTEN SCREW o A a o F A V 15 ADJUSTING STEP 4 Instruction of keystone adjustment movement 1 Tuner G does clockwise movements and it s function is to move structure frame 6 to drive projector towards a clockwise Y axis direction rotation adjustment picture D 2 Tuner G does anti clockwise movements and it s function is to move structure frame 6 drive projector towards an anti clockwise Y axis direction rotation adjustment picture C 3 The maximum adjustable angle is 5 degree Z G TRAPEZOID TIGHTEN A SCREW NY CTC MD i ee l a SS SaaS ma SCREENSHOT C G TRAPEZOID TIGHTEN SCREW V FRAME 6 DS SCREENSHOT D 16 ADJUSTING STEP 5 Instruction of image size adjustment movement 1 Loosen screw D 4 M4 10mm slightly Move structure frame 5 forward and backward to adjust its position in Y axis 2 For the distance between screen and projector please refer to the projector sheet P 7 3 When the image size is OK please tighten
11. n of left and right adjusting movement 1 Loosen screw C 2 M4 10mm slightly Y 2 Push structure frame 3 left or right directly to conduct adjustment 3 Adjust screw C to the proper position X axis direction and lock it 2 M4 10mm 4 The maximum adjustable distance is 30mm X C 2 M4 10 PARALLEL ROTATION TIGHTEN SCREW 7 NE 3 y PI LI 13 ADJUSTING STEP 2 Instruction of up and down rotation movement 1 Tuner E does clockwise movements and its function is to adjust structure frame 6 to drive projector into clockwise X axis direction rotation adjustment picture A 2 Tuner E does anti clockwise movements and its function is to adjust structure frame 6 to drive projector into anti clockwise X axis direction rotation adjustment picture B 3 The maximum adjustable angle is 5 degree E VERTICAL ROTATION Z ADJUSTMENT NUT R M Y SCREENSHOT A E VERTICAL ROTATION ADJUSTMENT NUT SCREENSHOT B 14 ADJUSTING STEP 3 Instruction of left and right rotation movement 1 Screw F for and rotate axis nut slightly 2 Take the rotation axis as the axis Z axis adjust the setting disc through horizontal left and r
12. nd tighten the screw see picture 2 to ensure that the installation is correct and reliable SETTING DRILLING PAPER OF f BRACKET 1 PROPER POSITION er ALIGN THE CENTRAL VERTICAL LINE ON THE SCREEN a SES F M VERTICAL ADJUSTMENT ROTATION SREW yes TI U gt m mmm snim a 00 SCREENSHOT 2 J 4 M8 70 SETSCREW 60 INSTALLING STEP 2 Installing steps of structure frame 2 1 Place structure frame 2 s neck into structure frame 1 s up and down adjusting screw inserts 2 Screw B screw M4 10mm into structure frame 1 s corresponding threaded hole slightly 2 PCS of both left and right side 3 Use up and down adjusting screw to adjust structure frame 2 to proper position and tighten HES BRACKET 2 STOP GROOVE M VERTICAL ADJUSTMENT ROTATION SCREW RAME 1 FRAME 2 B 4 M4 10 BRACKET 2 TIGHTEN ee BEFORE INSTALLATION T 2 es jeu Ce AFTER INSTALLATION 10 INSTALLING STEP 3 Installing steps of structure frame 2 1 Loosen C screw 2 M4 10mm 2 Decline the three axis fine tuner by 5 degree to aim at the registration mast As illustrated in the following picture 2 install the slide way on structure frame 2 s slide way and switch it to intermediate position 3 Tighten screw C 2 M4 10mm in
13. nt holding strength of the wall or improper installation The installation should be conducted by two qualified person concurrently If it is necessary to unscrew any nuts please take care that the wall mounted bracket does not fall If the hanger or the projector falls personal injury or property loss may occur N WARNING If the wall mounted bracket is meant for installation of the projector on walls and the wall should be strong enough to hold the projector and wall mounted bracket The wall mounted bracket should be installed on concrete walls The quality of projector and hanger should be qualified before installation and the strength of walls should be verified and maintained lf the strength of walls is not strong enough please strengthen them before installation Please test the wall mounted bracket at regular intervals so as to make sure that there are no broken parts or loose screws lf any broken part is found please refrain from using the wall mounted bracket If the wall mounted bracket or projector falls personal injury or property loss may occur Please do not with or modify the wall mounted bracket Please do not hang up the wall mounted bracket or hang things on the wall mounted bracket If the projector or the wall mounted bracket falls personal injury or property loss may occur Glues lubricant or oil should not be used to wall mounted bracket can chemical attack which could result in a rupture of the wall mounte
14. screw D 4 M4 10mm 4 The maximum adjustable distance is 120mm 4 M4 10 ADJUST FORWARD AND Z BACKWARD TIGHTEN SCREWS j als 120 i a Pn 3 A i X h Hr B A W L 4 M4 10 ADJUST FORWARD AND _ BACKWARD TIGHTEN SCREWS FRAME 5 JA 3 m si l ADJUSTING STEP 6 Instruction of image up and down adjustment movement 1 Loosen screw B 4 M4 10mm slightly In order to adjust the image s up and down position turn M up and down adjustment rotation screw to make sliding structure frame 2 up and down so as to adjust the image position up and down Z axis direction 2 Please refer to the projector distance sheet P 7 for the highest position of screen to the projector s up and down distance H1 3 When the image up and down position is well adjusted tighten screw B 4 M4 10mm 4 The maximum adjustable distance is 40mm WARN NG AFTER ALL THE ADJUSTMENT PLEASE TIGHTEN ALL SCREWS AND NUTS OTHERWISE THE PROJECTOR AND WALL MOUNTED BRACKET MAY FALL AND CAUSE PERSONAL INJURY OR PROPERTY LOSS A Z X V ADJUST VERTICALLY THE ROTATION SCREW r L o x m A o Bp E b gt gt f SEE B 2222 L B 4 M4 10 ADJUST VERTICALLY TIGHTEN SCREWS SCREEN 7 18 v vi tek Service Vivid Color Vivid Life C Vivitek China No 1090 Century Avenu
15. to structure frame 2 s corresponding threaded hole slightly do not lock it Adjust the screw C to proper position and tighten it 2 M4 10mm C 2 M4 10 PARALLEL ADJUSTMENT FIXING SCREW FRAME 2 SLIDE FRAME 3 ee gt l SCREENSHOT 1 A Sw lt A Si z TRI AXIS FINE TUNE it 5 FRAME A BEFORE INSTALLATION C 2 M4 10 PARALLEL SCREENSHOT 2 ADJUSTMENT FIXING SCREW o o a o o o o o o A o o o ADJUST IT AROUND TO MIDDLE OF THE SET gt GE POSITIONING POLE AFTER INSTALLATION 11 INSTALLING STEP 4 Installing steps of projector 1 Loosen screw H 4X M4 10 and remove structure frame 7 2 Use I screw 3 M4 10mm to connect structure frame H 7 and projector and assemble them together 3 Assemble the connected structure frame 7 and projector on structure frame 6 4 Tighten screw H 4 M4 10mm into structure frame 6 s corresponding threaded hole slightly not locked 5 Slide structure frame 7 to proper position and tighten screw H 4 M4 10mm H 4 M4 10 BRACKET 7 ETE TIGHTEN SCREW ri kI m m z L P l FRAME 6 Z 1 3 M4 10GHTEN SCREW FRAME 7 PROJECTOR CONNECTION SCREW AFTER INSTALLATION 12 ADJUSTING STEP 1 Z Instructio
16. vivitek Vivid Color Vivid Life INSTALLATION MANUAL English Edition D75X ULTRA SHORT SERIES SAFETY INSTRUCTION For your safety please read the instruction before using the wall mount bracket Any improper disposition caused by ignoring this manual may damage the hanger frame and result in personal injury and property damage Please keep the manual properly for future reference Please read the installation manual and safety instruction of the projector that matches our wall mount bracket and operate according to the instruction SYMBOL INSTRUCTION In order to avoid personal injury and property damage the following warning symbols are used in this setting manual Please make sure that you have understood all these warning symbols while reading this instruction Ignoring this signal may lead to improper handling and result in personal injury even death Ignoring this signal may lead to improper handling and result in personal injury or machine damage N WARNING CAUTION Useful messages N Compulsory operations that must be conducted D Recommended operations that should be conducted SAFETY PROTECTION MEASURES FOR SETTING The wall mounted bracket is designed for installation of projector on walls The weight of the installation object other than the designed projector may damage the wall mounted bracket and if the wall mounted bracket falls D personal injury and property damage may happen

Download Pdf Manuals

image

Related Search

Related Contents

Black Box VDSL Line Driver User Manual  4 - Pump SA Control Panel v1.0.1    8,000 BTU Portable Air Conditioner, Dehumidifier and Fan  Guía de inicio rápido HT-S3505 Accesorios suministrados    Product Booklet 26042013 - Portable Solar Panels & Caravan  EST-P1 Owner`s Manual  AKG Acoustics CGN321 STS User's Manual  SA304X-8 Instruction Manual  

Copyright © All rights reserved.
Failed to retrieve file