ADEMCO 5801
Contents
1. hourly check in signal and must not be taken out of range of the control receiver See the control unit s Installation Instructions for further details regarding programming SELECTION OF FUNCTIONS FOR BUTTONS For convenience the 5801 is supplied with the buttons labeled with the functions shown in Figure 1 Labels for these particular functions were chosen since they are those likely to be selected for most LED installations However additional labels are provided for those cases puny fa where other functions are desired simply attach the new label over the existing one In all cases each Le al PANIC button must be programmed for its desired function as indicated in the PERE TAON EE e control unit s installation instructions IMPORTANT NOTE If the Function 4 button is not e a used it MUST be programmed as a Not used zone type FUNCTION 2 STAY i i 5801 002 VO Figure 1 5801 Transmitter BATTERY INSTALLATION 1 Remove the cover by inserting the blade of a small screw driver into the slot at the bottom of the case and twisting Install the Lithium battery supplied in the battery compart ment observing correct polarity see Figure 2 Make sure the battery is firmly seated 3 Replace the cover snap fit BATTERY CAUTION Risk of fire explosion and burns Do not recharge disassemble heat above 100 C or incinerate Dispose of used batteries promptly Keep away fro2. N6478V3 5 05 Rev B Honeywell ADEMCO 5801 Remote Wireless Panic Transmitter INSTALLATION AND SETUP GUIDE GENERAL The ADEMCO 5801 is a portable unit which can be programmed at the control receiver to perform up to four system functions e g arm STAY arm AWAY Panic disarm etc No audible or visual system status indications are provided by the 5801 except for a Red LED indicator which flashes when the unit transmits The 5801 is intended for use only with wireless alarm systems that support 5800 series devices The transmitter may be left unmounted resting on a table countertop or other surface or carried in a pocket or purse If the unit will not be wall mounted remove the mounting plate attached to the back of the unit see step 1 of WALL MOUNTING instructions on the other side Ensure that a transmission is received from each area where usage of this transmitter is anticipated PROGRAMMING The 5801 has four unique identification codes permanently assigned during manufacture You must enroll these codes into the control system at some point prior to usage of the system Each button must be enrolled by the control receiver See Important Note below IMPORTANT PROGRAMMING NOTE THE 5801 TRANSMITTER MUST BE PROGRAMMED AS ONE OF THE FOLLOWING INPUT TYPES ONLY UR type unsupervised RF or RF type supervised RF The UR type is supervised only for battery status whereas the RF type is supervised for an
3. could void the user s authority to operate the equipment N6478V3 5 05 Rev B Honeywell 2 Corporate Center Drive Suite 100 P O Box 9040 Melville NY 11747 Copyright 2009 Honeywell International Inc www honeywell com security
4. m children WALL MOUNTING OPTIONAL To wall mount the unit proceed as follows 1 Disengage the supplied wall mounting plate from the unit by sliding it along the case back 2 Attach the mounting bracket in the desired location with the hooks pointing upward using the two screws supplied The word TOP is molded along the upper edge of the plate 3 Locate the keyhole slots on the back of the transmitter case onto the bracket s LITHIUM BATTERY ADEMCO 466 5801 003 VO Figure 2 5801 Cover Removed hooks and secure by sliding the case downward firmly SPECIFICATIONS Size 4 x 2 1 4 x 13 16 102mm x 57mm x 21mm LED Flashes when unit transmits Battery 3 volt Lithium Use only ADEMCO 466 Duracell DL123A Panasonic CR123A Sanyo CR123A REFER TO THE INSTALLATION INSTRUCTIONS FOR THE RECEIVER CONTROL WITH WHICH THIS DEVICE IS USED FOR WARRANTY INFORMATION AND FOR DETAILS REGARDING THE LIMITATIONS OF THE ENTIRE ALARM SYSTEM This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User s Manual Unauthorized changes or modifications
Download Pdf Manuals
Related Search