Untitled - Audio Integrate
Contents
1. AMC 2 Contents The New Mic W series of AMC Wireless systems created for active musician and presenters who also manage their own sound AMC Mic W improves your performance and simplifies your setup Mic W wireless microphone system deliver the crystal clear sound quality that pro audio engineers trust CONTENTS Wireless system features 3 System components 3 Front panel 3 Rear panel 4 Handheld transmitter 4 Operation 5 Operation menu 5 Receiver setup 6 Handheld microphone setup 6 Batteries installation 7 Specifications 8 3 Wireless System Features System components All system includes Receiver Handheld transmitter 2 AA batteries 1 4 jack audio connecting cable Power supply 2 antennas 8 User manual Front panel Power switch O FF level indicators Power indicator AF level indicators LED indicator for antenna A O Volume control knob LED indicator for antenna B 4 Wireless System Features Rear panel 300 mA III CAUTION ote AMC Use oniy original IMIC W UHF TRUE DIVERSITY O Antenna B connector DC power supply connector XLR balanced audio output AntennaB connector 1 4 jack unbalanced audio output Handheld transmitter Microphone head Low battery LED indicator Power on off mute switch Microphone body oo 8 Battery port 2 AA Alkaline batteries gt Operation Operating Men2. t 102dB T H D lt 0 6 1KHz Working range 100m Note actual range depends on RF signal absorption reflection and interference Operating temperature range 10 C 40 C Receiver Frequency range 863 4MHz 863 8MHz 864 3MHz 864 8MHz Antenna BNC 50Q Sensitivity 107dBm Image rejection gt 60dB Max Audio output 12 dB V Transmitter Antenna built in spiral antenna for the handle microphone Power output 10mW Battery 2 5 AA Alkaline battery AMC is a registered trademark of AMC Baltic www amcpro It C
3. the Mic W receiver near digitally controlled equipment e Plug the DC power supply into the power connector on the back of the receiver Connect the other end of the power supply into an electrical outlet e Attach the A and B antennas to the ANTENNA connectors e Connect audio cable from the audio output s to the audio input s of your audio system mixer and or amplifier e Turn on the receiver by pressing the power button Handheld microphone setup Open the battery cover and insert 2AA alkaline batteries e Slide the transmitter ON MUTE OFF switch to the ON position The power LED will glow for the moment e Slide the transmitter ON MUTE OF switch to the MUTE position if the wireless system should be used in silent mode Please note that the microphone is still consuming power when it is muted e f the battery indicator lamp is shining it shows that the battery is low and needs to be replaced e After finished using the transmitter switch off the power source Remove the batteries when storing for long time Batteries installation Handheld Transmitter 1 Open the battery cover 2 Insert the 2 AA Alkaline battery 3 Close the battery cover 8 Specifications Specifications for system Carrier frequency range 863 4MHz 863 8MHz 864 3MHz 864 8MHz Modulation FM Frequency stability 0 005 Dynamic range gt 90dB Max Deviation 48KHz Frequency response 50Hz 16KHz 3dB S N ratio g
4. u Before turning on the receiver firstly ensure that the transmitter is switched off and then adjust receiver volume to the min e Lastly turn on the transmitter power radio frequency decibel meter on the receiver will starts indicate RF level After this adjust receivers audio output level to suitable size and speak into the microphone the receiver audio frequency decibel meter lightens in corresponding to microphone volume level If voice output is not hearable and the decibel meter is not bright overhaul transmitter and receiver e Distance between the receiver and the transmitter should not be too far max 80 meters e Transmitter and receiver should be in direct access and least obstacles should be met in path between them e When the receiver is used with omni directional antenna the antenna should be minimum 0 5m from the wall and should be kept far away from any other metal constructions e Handheld transmitter should be grasped in the middle of full length not too close to the microphone head or power button and not too close to base antenna position It prevents from accidentally switching off and radio frequency suppression e Changing active distance between the microphone and lips may cause fluctuation in high frequency reproduction 6 Operation Receiver setup e Put iMic W receiver on a table or other horizontal surface Mic receiver can also be rack mounted using one of the Rack Mount Kits e Do not place
Download Pdf Manuals
Related Search