- Whirlpool
Contents
1. abrasive sponge neither corrosive detergents when cleaning black burners e Clean them by hand with warm water and non abrasive detergent removing any food residues and checking that none of the burner openings is clogged e Rinse and dry e After cleaning black burners changes in appearance can be noticed in the uncoated bottom surface of the burners or either after several cleaning cycles on the black coated surface These esthetical changing though do not impact product quality neither its performances e Refit burners and burner caps correctly in the respective housings e When replacing the grids make sure that the panstand area is aligned with the burner e Models equipped with electrical ignition plugs and safety device require thorough cleaning of the plug end in order to ensure correct operation Check these items frequently and if necessary clean them with a damp cloth Any baked on food should be removed with a toothpick or needle NOTE to avoid damaging the electric ignition device do not use it when the burners are not in their housing SERVICE AND MAINTENANCE To ensure your appliance is always working correctly check all functions on the product periodically eg every 2 months that it is operating correctly and if there appears to be any abnormalities please contact the service call centre for advice For further details please refer to the warranty terms and conditions provided inside the back of the user manual Regul2. ECTION 1 Check the gas type sticker attached to the hotplate Details of the injector sizes used are recorded on the data plate located on the base of the appliance 2 This appliance shall be installed in accordance with installation requirements of the local gas authority of the appropriate installation code The gas supply system must comply with local regulations to the current relevant gas standard AS NZS 5601 current edition 3 Before installing the hotplate consider the location of the gas supply and routing the gas line Refer Fig 1 4 For ULPG models the gas supply for the hotplate must be regulated to a pressure of 2 75kPa The gas inlet connection fitting is 2 B S P male thread in compliance with ISO 7 thread 5 For NG models the gas supply is connected to a regulator which is supplied The inlet connection has 2 B S P male thread IT IS ESSENTIAL THAT THE ELBOW ON THE APPLIANCE BE HELD FIRMLY WITH A SPANNER DO NOT OVER TIGHTEN The regulated pressure for NG is 00kPa 6 A manual shut off valve must be installed in the gas line in an accessible position external to the hotplate so that in the event of an emergency or service the gas supply can be shutoff 7 For gas inlet position of appliance refer Fig 2 for NG and fig 3 for ULPG After installing the gas supply and making all connections check thoroughly for possible leaks Turn all control knobs on the unit to OFF position Open the valve on the gas sup
3. PRODUCT DESCRIPTION SHEET 1 Removable panstand grids DIMENSIONS AND DISTANCES TO BE MAINTAINED mm Auxiliary burner Semi rapid burner Semi rapid burner oe SS 2 ring burner min A 6 5 a max R 16 a Auxiliary burner control knob 7 Semi rapid burner control knob Semi rapid burner control knob 9 2ring burner control knob Pha Symbols Tap closed gt J 1 9 8 T 6 A Maximum flame A Minimum flame l ji li a NOTE In case of installation of a hood above the cooktop esee re to the hood instructions or the correct distance LIGHTING THE BURNERS NOTE the indicated clearance dimensions are applicable to all non combustible materials e To ignite one of the burners turn the relative knob anti clockwise to the maximum flame setting Gas Tne Natural 1 00 kPa Universal LP 2 75 kPa e Press the knob against the control panel to ignite the burner yp test point ee inlet i e After the burner has ignited keep the knob pressed for about 5 seconds to allow the thermocouple to warm up ee This burner safety device shuts off the gas supply to the burner if the flame goes out accidentally because of sudden MJ h Size S Consumption MJ h Size mm draught an interruption in the gas delivery boiling over of liquids etc e The device must not be pressed for more than 15 sec If after that time has elapsed the burner does not FRONT RHS FRONT RHS Auxiliary The burner might go out when th
4. ar care and maintenance ensures correct operation and high performance To maintain your hob in perfect condition clean it after every use removing any food spills TROUBLESHOOTING GUIDE The hob may not work or work incorrectly Before calling the After Sales Service refer to the Troubleshooting Guide to determine the problem 1 The burner fails to ignite or the flame is not even Check that The gas or electrical supplies are not shut off and especially that the gas supply tap is open The gas cylinder liquid gas is not empty The burner openings are not clogged The plug end is not dirty All the burner parts have been positioned correctly There are no draughts near the hob The burner does not stay lit Check that When lighting the burner the knob has been pressed for enough time to activate the protection device The burner openings are not clogged near the thermocouple The end of the thermocouple is not dirty The minimum gas setting is correct see relevant paragraph The containers are not stable Check that The bottom of the container is perfectly flat The container is centered on the burner e The grids have not been exchanged or positioned incorrectly If after the above checks the fault still occurs get in touch with the nearest After Sales Service AFTER SALES SERVICE Before calling the After Sales Service make sure you can give the following information type of fault or problem exact mo
5. del written on the Product Description Sheet and Warranty service number that follows the word SERVICE on the rating plate under the hob and on the Warranty your complete address and phone number If any repairs are required please contact an authorised After Sales Service as indicated in the warranty N ote Failure to comply with these instructions may compromise the safety and quality of the product JAAK 0000 000 00000 eeee N o o o o o o eo W Customer Service Contact Details Australia 1300 363 344 www whirlpool com au New Zealand 0800 442 584 www whirlpool co nz Manufacturer Whirlpool Europe S r l Viale G Borghi 27 21025 Comerio VA ITALY
6. e knob is released This means that the thermocouple has not warmed up enough REAR LHS Semi Rapid C 68 a 5B TT PRATICAL ADVICE FOR USING THE BURNERS For better burner performance please stick to the following rules Burner Pot ELECTRIC SUPPLY 220 240 V 50 60 Hz 0 6VA Use pots and pans that fit the burners see table on the Fron Ato 26cm WOK ADAPTER Only use flat bottomed pots and pans Use the correct amount of water for cooking foods and keep the pot covered In the case of pans with convex bottoms WOK use the support grille provided which should be positioned only on the 4 ring burner Due to continued product development Whirlpool reserves the right to change specifications or model availability without notice 5019 300 02566 To get full satisfaction from the hob please read these instructions carefully and keep them for future consultation Whirlpool is a registered trademark of Whirlpool USA Copyright Whirlpool Europe S r l All rights reserved PRECAUTIONS AND GENERAL ADVICE To get full satisfaction from your hob please read these instructions carefully and keep them for future consultation e These instructions are only valid for those Countries where the destination abbreviations are mentioned on the product description sheet and on the hob e Keep the packaging material plastic bags polystyrene parts etc out of the reach of children as they are potentially dangerous e C
7. he rating plate change the injectors Use pressure regulators suitable for the gas pressure indicated in the Product Description Sheet e The gas nozzles must be changed by After Sales Service or a qualified technician e Nozzles not supplied with the appliance must be ordered from After Sales Service e Adjust the minimum setting of the taps N ote when liquid petroleum gas is used ULPG the minimum gas setting screw must be tightened as far as it will go or until the flame is small and stable enough to keep it alive Should you experience difficulty in turning the burners knobs please contact the After Sales Service for the replacement of the burner tap if found to be faulty REPLACING THE INJECTORS see the injector table in the Product Description Sheet e Remove grids A e Extract burners B e Using a socket spanner of the appropriate size unscrew the injector C e Replace it with the injector suitable for the new type of gas Before installing the hob remember to affix the gas calibration plate supplied with the injectors in such a way that it covers the existing information relating to gas calibration N ote Ensure to REMOVE the NATURAL GAS REGULATOR device and replace with the PROPANE LPG TEST POINT ADAPTOR ADJUSTING MINIMUM GAS SETTING OF TAPS To ensure that the minimum setting is correctly adjusted remove the knob and proceed as follows e tighten the screw to reduce the height of the flame e
8. heck whether the hob has been damaged during transport and remove any protective film from the appliance parts e This hob Class 3 is designed solely for household use for cooking food Any other use such as heating rooms is to be considered improper and as a consequence dangerous e Ensure that the installation and gas electrical connections are performed by a qualified technician in compliance with current local safety regulations e This appliance should only be installed and used in well ventilated rooms in accordance with current regulations Carefully read the instructions before installing and using this appliance e Gas adjustment and supply pressure are indicated on the rating plate located under the hob If the appliance is arranged for a type of gas different from that available refer to the paragraph Ajustment to different types of gas e WARNING DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION e WARNING ONLY APPLIANCE WITH SAFETY DEVICE BURNERS CAN BE INSTALLED IN MARINE CRAFT OR CARAVANS IN ANY CASE IT SHALL NOT BE USED AS A SPACE HEATER e WARNING DO NOT USE OR STORE FLAMMABLE MATERIALS IN THE APPLIANCE STORAGE DRAWER OR NEAR THIS APPLIANCE PROVISION FOR VENTILATION ROOM VENTILATION To ensure correct operation of the appliance the room size in which it is to be installed shall be in accordance with AS5601 This room must also be continuously ventilated fresh air should flow t
9. hrough permanent openings in walls to outside or to an adjacent non inhabitable room as detailed is AS 5601 These permanent openings must be made in such a way that it cannot be obstructed from either side of the wall also they should be protected by plastic grids metallic mesh etc taking care not to reduce the air vent effective area mentioned above and located near floor level and positioned so as not to interfere with the operation of the exhaust system the minimum cross section of these permanent openings is set by AS6501 and shown in Fig la Ib and Ic OVERHEAD CLEARANCE Range hoods and exhaust fans shall be installed in accordance with the manufactures instructions However in no case shall the clearance between the top of the highest burner of the cooking appliance and the range hood be less than 600 mm or for an overhead exhaust fan 750 mm Any downward facing combustible surface less than 600 mm above the top of the highest burner shall be protected for the full width and depth of the cooking surface area in accordance with Clauses 5 12 1 2 of AS 5601 However in no case shall this clearance to any surface be less than 450 mm SIDE CLEARANCE Where the distance measured between the periphery of the burner and any vertical combustible surface is less than 200 mm the surface shall be protected in accordance with Clause 5 12 1 2 of AS5601 to a height of not less than 150 mm above the hotplate top surface for the full length and width
10. loosen the screw to increase the height of the flame The adjustment must be performed with the tap in minimum gas setting position small flame e The primary air of the burners does not need to be adjusted e Atthis stage light up the burners and turn the knobs from max position to minimum position f to check flame stability Upon completion of adjustment reseal using sealing wax or an equivalent material SERVICE INSTRUCTIONS Service and maintenance only to be carried out by an authorised person To replace parts such as burners valve and electric components the hotplate must be removed from the bench top by releasing the attachment hooks loosening the attachment screws of each burner unscrewing the hotplate attachments nuts which are visible at the bottom of the surface removing the hotplate top taking care to remove lid taps and screws under them and finally replacing the defective parts N ote If the valves must be replaced first disassemble the chain of ignition switches It is recommended to replace the valve gaskets each time the valve is replaced thus ensuring a perfect seal between the body and the gas train WARNING Do not modify this appliance CLEANING THE HOB SURFACE WARNING Disconnect power before servicing e All the enamelled and glass parts should be cleaned with warm water and neutral solution e Stainless steel surfaces may be stained by calcareous water or aggressive detergents if left in con
11. n ASS 2228223 2h 5 2am a m y GE K a s SR We SPUR E TEN O Pat aTi PLS BAINS TERMINI POOL SPARE ype T iON gt Ony Late 230 240 V e The manufacturer cannot be held responsible for any injury to persons or animals or damage to property arising from failure to comply with these requirements e When the hob is installed provide a single pole circuit breaker with a contact separation of at least 3 mm e If necessary the electrical power cable must be replaced exclusively with a power cable having identical characteristics to the original supplied by the manufacturer type HO5V2V2 F T90 C or HO5RR F This operation must be performed by a Qualified Technician or Authorised Person ASSEMBLY After having cleaned the perimeter surface apply the supplied gasket to the hob as shown in the figure 7 Position the hob in the worktop opening made respecting the dimensions indicated in the Product Description Sheet N ote the power supply cable must be long enough to permit its upward extraction To secure the hob use the brackets A provided with it Fit the brackets into the relevant bores shown by the arrow and fasten them by means of their screws in accordance with the thickness of the worktop see figures on the right Top 40 mm ace ADJUSTMENT TO DIFFERENT TYPES OF GAS If the appliance is intended to operate with a different gas from the gas type stated on t
12. of the cooking surface area Note the cooking surface area is defined as the part of the appliance where the cooking normally takes place and does not include those parts of the appliance containing the control knobs As Min ventilation requirement A E gt for air entry 100 cm As long as air intake matches the capacity of the air exhaust fan Min ventilation requirement Min ventilation requirement for air entry 100 cm a gt for air entry 100 cm Fig la Fig 1c Fig 1b PROTECTING THE ENVIRONMENT 1 Packaging The packaging material is entirely recyclable and is marked with the recycling symbol which identifies it as a type of material that must be sent to local waste disposal centres 2 Product The hob is made out of recyclable material Before disposing of it cut its power cable off in order to render it inoperative and shut off the gas supply Dispose of it in a waste disposal centre in compliance with local regulations NOTES e Improper use of the grids can result in damage to the hob surface Do not position the grids upside down or drag them across the hob e Incase of prolonged use additional ventilation may be needed opening a window or increasing the extraction force of the hood e The appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or with lack of experience and knowledge of the appliance unle
13. ply Using a soap and water solution check each gas connection one at a time by brushing the solution over connection Presence of bubbles will indicate a leak Tighten the fitting and re check for leaks If it is not possible to correct the leak replace fitting Under no circumstance use matches or flame for checking leaks 8 Turn on appliance gas cock and light each burner Check for a clear blue flame without yellow tipping If burners shows any abnormalties check the following Burner cap on correctly Burner positioned correctly Burner vertically aligned with injector nipple 9 In some cases the burners will fail to ignite immediately and will seem to blow s lightly when they do ignite this is usually due to air in the gas pipe which should clear itself within seconds of operation 10 If after following the instructions given satisfactory performance cannot be obtained contact the local gas authority for advice and assistance WARNING Appliance not suitable for connection with flexible hose assembly 46 24 e a n m ag bd ELECTRICAL CONNECTION POINT z T GAS CONNECTION PRESSURE PRESSURE POINT TEST POINT TEST POINT Fig 3 Fig 1 Fig 2 ELECTRICAL CONNECTION e The electrical connections must comply with local regulations e The data relevant to the voltage and power absorption are indicated on the rating plate n earthing of this appliance is compulsory by aw L Earth _ yellow gree
14. ss supervised or previously instructed in its use by those responsible for their safety e Keep children away from the hob when it is in use and do not let them play with the controls or any other appliance parts Warning the protective rubber feet on the grids represent a chocking hazard for young children After removing the grids please ensure that all the feet are correctly fitted INSTALLATION TECHNICAL INFORMATION FOR THE INSTALLER e This product can be embedded in a worktop 20 to 40 mm thick e Ifthere is no oven beneath the hob insert a separator panel that has a surface at least equal to the opening in the work surface This panel must be positioned at a maximum distance of 150 mm below the upper surface of the work surface but in no case less than 20 mm from the bottom of the hob In the case that you intend to install an oven beneath the hob make sure that it is equipped with a cooling system The manufacturer declines all liability if another brand oven is installed beneath the hob e Before installation make sure that the local gas delivery conditions nature and pressure are compatible with the settings of the hob see the rating plate and injector table The outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations Combustion products are discharged outdoors through specific hoods or wall and or window mounted electrical fans INSTALLATION GAS CONN
15. tact for too long Any food spills water sauce coffee etc should be wiped away before they dry e Clean with warm water and neutral detergent and then dry with a soft cloth or chamois Remove baked on dirt with specific cleaners for stainless steel surfaces NOTE clean stainless steel only with soft cloth or sponge Do not use abrasive or corrosive products chlorine based cleaners or pan scourers Do not use steam cleaning appliances Do not use flammable products Do not leave acid or alkaline substances such as vinegar mustard salt sugar or lemon juice on the hob Small scratches on black burners could be noticed after use and cleaning or either since the beginning as a natural effect of the product transportation and may be due to their friction with burner caps These scratches though do not impact product quality neither its performances We recommend to handle and place burner caps avoiding to twist them in order to minimize esthetical potential scratches e Clean black burners following recommendations indicated in CLEANING THE HOB PARTS section If you have a IX ELIUM hob observe the following cleaning recommendations e Use a soft cloth microfibre is best dampened with water or with everyday glass cleaning detergent e Do not use paper kitchen towel which can leave traces of streaks on the hob SETANE THE HOB PARTS Grids burner caps and burners can be removed to be cleaned e Handle black burners carefully Do not use
Download Pdf Manuals
Related Search