ARIES - Kunzle & Tasin
Contents
1. am o N N am lt Diagrams A o 28 O Lo Lu CM N Wi i am o N N am lt D FIG Diagrams ARIES User Manual March 2013 Edition 30 ARIES User Manual March 2013 Edition 31 March 2013 Edition 322. 9 Connect the plug to the socket 10 Ensure the lever pos 4 fig A is lowered and the drum is raised from the floor 17 ARIES User Manual march 2013 Edition Starting the machine 11 To start the machine j 2 3 4 Stand behind the handle Turn the knob on the switch pos 10 fig B from the 0 position to the START position Keep it in this position until the motor has reached a sufficient rotation speed Release the knob on the switch which will automatically return to work position 1 12 Observe the operation of the abrasive belt To adjust belt position follow the PROCEDURES FOR CENTRING THE ABRASIVE BELT pg 19 13 Close the abrasive cover pos 11 fig B 14 After lowering the lever pos 4 fig A commence sanding 18 ARIES User Manual march 2013 Edition Starting the machine IMPORTANT If starting the machine is difficult in winter when temperatures are very low remove the abrasive belt and start the motor letting it idle for several minutes Replace the belt and repeat the start up operations described above WARNING A safety contactor is fitted to the machine If the power fails when sanding the contactor is activated automatically stopping the machine from accidentally starting up when the power is restored To recommence sanding repeat the start up operations described above Machine adjustment procedures The belt centres automatically on starting the motor
3. WARNING The belt is positioned correctly when itruns along the inside of the tensioning drum A it protrudes approximately 2 mm outside the rubber drum B When first fitted the belt may be in the wrong position In this case use the spanner as shown pos 13 fig D marked by the yellow arrow and proceed as follows Stand in front of the machine to check that following operation the belt is positioned correctly Turning the screws anti clockwise moves the belt towards the outside 1 Turning the screws clockwise moves the belt towards the inside 2 a a al wines Fh a LE e 1 E err EE ae ne 19 ARIES User Manual march 2013 Edition To vary drum pressure on the floor use the adjustment knob pos 14 fig E and proceed as follows 1 Turn the adjustment knob clockwise to 2 Turn the adjustment knob anti clockwise to decrease drum pressure on the floor increase drum pressure on the floor A support with a free castor has been fitted to avoid damage to the skirting board or wall when sanding along the wall WARNING The wall edge castor is correctly positioned when the machine is approximately 8 mm away from the wall with the castor up against it Before starting work position the castor correctly by unscrewing the screw pos 12 fig C moving the support to the required position and tightening the screws 20 ARIES User Manual march 2013 Edition Machine adjustment proce
4. ARIES WOOD SANDER MAINTENANCE MANUAL ARIES User Manual march 2013 Edition Foreword This manual contains important information on the safe use and operation of this machine Failure to read this manual before operating adjusting or servicing this machine could cause injury or damage to persons or objects Anybody operating the machine should understand how to use and operate it before starting it up Keep this manual for future reference This manual is an ENGLISH translation of the original version in Italian K NZLE amp TASIN For a new manual contact Kunzle amp Tasin S r l REGISTERED HEADQUARTERS Via Circonvallazione est 2 6 27023 Cassolnovo PV Italy OPERATIONAL HEADQUARTERS Via Cajkovskij 14 20092 Cinisello Balsamo MI Italy Tel 39 02 66040930 Fax 39 02 66013445 info kunzletasin com www kunzletasin com ARIES User Manual march 2013 Edition Contents Key for machine symbols Operator safety instructions Storage Transporting and handling the machine Transport with one person Transport with two people Introduction Information on safe use Correct use Machine data plate Commencing operation Instructions for assembly following transportation Instructions for electrical connection Cables extensions and plugs Instructions on removing sawdust generated during use Recommendations on prevention measures for users Personal safety measures Compliance with safety mea
5. The vacuum cleaner belt must have a 8 mm stretch with a centre load of 18 2N The belt tension can be adjusted using the belt tightener 4 HAZARD Using the machine when not fully assembled may cause injury or damage to people or objects Do not use the machine when it is not fully assembled Keep all fittings tightly closed Maintain machine settings in accordance with the specifications 6 Fit the suction pipe and drum control rod 10 ARIES User Manual march 2013 Edition Commencing operation 7 Lift the drum with the lever pos 4 fig A 8 Connect the power supply cable to the machine and power supply CAUTION This machine only operates with the voltage and frequency shown on the machine data plate Before connecting the cable to the power supply ensure the correct voltage and frequency are available WARNING Do not expose the machine to rain This machine is intended for dry use only Keep the machine in a dry building and do not use it in damp or wet places WARNING If the machine is not connected correctly to the electricity network death due to electrocution may occur To prevent electric shocks always use a three wire electrical system connected to earth For maximum protection against electric shocks use a circuit protected with a differential cut out switch WARNING Tampering with the earthing plug in any way may result in death from electrocution Do not cut remove or break the earthing plug If the
6. dimensions 750 x 203 mm 230V 50 Hz 2 2 kW 220V 50 Hz 2 2 kW Control lever grip control Level control via wheel cam Safety motor protection THERMAL In the event of a power cut the motor will not start without manual intervention Wheels 80 mm replaceable Bearings lifetime lubricated ball bearings Drum pressure adjustment infinite adjustment Noise level IEC 60704 1 86 dB A max continuous weighted sound pressure level A measured at a distance of 0 4 m from the handle and a height of 1 5 m from the ground Vibration lt 1 45 m m s2 weighted value of the mean square deviation of the acceleration Machine dimensions assembled 960 x 360 x 980 mm Net weight 60 kg Gross packaging dimensions 2 cardboard packages 680 x 370 x 640 mm Gross weight Cardboard packages 68 5 kg Standard equipment Dust bag Electric plug Start up keys User and maintenance manual 19 ARIES User Manual march 2013 Edition Machine warnings Starting the machine WARNING This equipment is not to be used by anyone children included with physical or mental disabilities or anyone without the relevant experience and knowledge unless they have received instructions on using the equipment and are supervised by a responsible person to ensure their safety WARNING CAUTION CAUTION This equipment is not suitable for collecting hazardous dust Using the machine to move objects or moving on an incline ma
7. drum pressure Increase belt tension Replace the belt Use cables of suitable length and cross section Arrange suitable connections Contact an authorised K amp T dealer Contact an authorised K amp T dealer Replace the abrasive Clean correct replace the rubber coated drum Correct the wheel position Empty the bag Shake out the dirt and wash the bag Clean air ducts Contact an authorised K amp T dealer Contact an authorised K amp T dealer Contact an authorised K amp T dealer Contact an authorised K amp T dealer Check power supply and connections Replace the abrasive Decrease sanding pressure Use abrasive with larger grain ARIES User Manual March 2013 Edition DECLARATION OF CONFORMITY DECLARATION OF CONFORMITY 2006 95 EC 2006 42 EC 2004 108 EC 2002 95 EC 2002 96 EC KUNZLE amp TASIN S r l Manufacturer and entity authorised to compile and maintain the technical file Registered headquarters Business Management and Production Site Via Circonvallazione Est 2 6 Via Cajkovskij 14 27023 Cassolnovo PV Italy 20092 Cinisello Balsamo MI Italy declare that under our sole responsibility the product BELT SANDER FOR WOOD FLOORS ARIES to which this declaration refers is compliant with the following Directives 2006 95 EC Low Voltage Directive 2006 42 EC Machine Directive 2004 108 EC EMV 2002 95 EC RoHS 2002 96 EC WEEE Directive The product is compliant with the fo
8. frame and the mobile cover on the abrasive drum The following information can be found on the machine data plate Name of manufacturer Country of manufacture Year of manufacture or see serial number Via Cajkovskij 14 20092 Cinisello B 1 Machine model eKUNZLE amp TASIN Milano Tel 02 66040930 2 Safety symbols TS ln FER ae BERO 3 Motor power 4 Frequency 5 Supply voltage 6 7 8 9 Serial number sERLAL N7 The serial number is formed as follows the first two numbers refer to the year of manufacture 13 2013 the second group of three numbers indicates the date the machine was gt tale Lr Faler T manufactured 029 29th January 501302916 the last two numbers indicate the progressive number of machines produced on that day of manufacture 16 sixteenth machine ARIES User Manual march 2013 Edition To re assemble the machine following transportation proceed as follows 1 Open the belt guard 2 Position the motor in its housing 4 Fit and stretch the belts 5 Close the belt safety guard 1 by tightening the relevant screw 2 ARIES User Manual march 2013 Edition Commencing operation CAUTION Excessive belt tension may cause the premature failure of the ball bearings The drum belt must have a 10 5 mm stretch with a centre load of 30 3N Belt tension can be adjusted using the screw pos 7 fig A photo 1 and the Allen nut marked with the yellow arrow in photo 2
9. use e g in hotels schools hospitals offices factories and shops The following information highlights particularly hazardous situations for the operator and or machine Understand when these conditions may be present Removing safety features could cause death or physical injury Take all steps necessary to instruct personnel who may use the machine Report any damage on the machine or incorrect operation immediately Keep hands and clothes away from rotating parts Keep hands on the handle when the motor is operating Do not leave the machine unattended when the motor is operating Always use the machine with the dust bag in the correct position Do not detach the dust bag with the motor operating Always disconnect the power supply cable from the machine before performing maintenance Transport the machine with care due to the heavy weight of the individual parts making up the machine a A mn TOM DO c Always use the machine in well ventilated areas 9 Always dispose of the sawdust appropriately 10 Use the type and amount of abrasive specified in the instruction manual 11 Always keep the work area well lit 12 The use of accessories other than those recommended in this manual may cause injury 13 The sander is for indoor use only 14 ARIES User Manual March 2013 Edition Machine specifications Drum width 200 mm Drum diameter 150 mm Drum speed 50 Hz 2400 revs min 60 Hz 2500 revs min Abrasive belt
10. water to prevent blockage of the pores and a decrease in dust collection ability As an alternative to the fabric bag the following may be used a Disposable paper bags in packs of 3 P N b Remote control industrial vacuum cleaner with tube 6300030142 along with the bag holder P N with maximum length of 10 metres 2999940049 The limit for use is 1 3 of the total capacity Check belt tension regularly For adjustment procedures see page 10 of this manual If the belt is excessively worn it must be replaced CAUTION Excessive belt tension may cause the premature failure of the ball bearings The belt must have a 10 5 mm stretch with a centre load of 30 3 N 23 ARIES User Manual March 2013 Edition Routine maintenance to be performed Check bearings regularly for wear or damage according to the following timescales WHEELS after the first BELT TIGHTENING PULLEY after the first FAN SHAFT after the first TENSIONING UNIT after the first SANDING DRUM after the first MOTOR SHAFT after the first Regularly check that the groove 2 of the pulley has not sunk otherwise the belt 1 will operate on the bottom 3 of the pulley itself WARNING Pulleys with sunken grooves cause the belts to slip and the correct power will not be transferred to the drum suction pipe For example this situation can easily occur if the machine loses power during operation They should therefore be replaced Spar
11. wear and tear Do not use the machine if the power supply cable is damaged Do not use the electric cable to move the machine Injury or damage may occur if the sander runs over the power supply cable and it becomes damaged Keep the cable away from the lower part of the machine to avoid contact with the abrasive Always keep the power supply cable raised above the machine The moving parts on this machine may cause serious injury and or damage Keep hands feet and loose clothing away from all moving parts of the sander Performing maintenance or replacing the dust bag may cause injury to the operator or people nearby if the machine is connected to the power supply 13 ARIES User Manual March 2013 Edition Recommendations on prevention measures for users WARNING Failure to comply with instructions on this machine and in this manual may cause serious injury and or damage Read and comply with all safety instructions Ensure that all plates labels warnings and instructions are secured to the machine New plates can be obtained from an authorised K amp T dealer CAUTION Injury or damage may occur if maintenance operations or repairs are carried out by unauthorised personnel CAUTION The machine may become damaged if it is not kept in a dry building Keep the machine in a dry building Instructions on correct machine use Read this manual carefully and become familiar with the machine The equipment is suitable for industrial
12. G means Failure to comply with WARNING notices on the machine or in this manual may result in injury to the operator or other people Read and comply with all WARNING notices on the machine or in this manual CAUTION means Failure to comply with CAUTION notices on the machine or in this manual may result in injury to the operator or other people Read and comply with all CAUTION notices on the machine or in this manual HAZARD Failure to read the ARIES machine manual before operating adjusting or performing maintenance operations on the machine could cause injury or damage to persons or objects Anyone operating the machine should understand how to use and operate it before starting it up ARIES User Manual march 2013 Edition Storage It is advisable to store the machine in its original packaging Doing so makes it possible to form a column of two packages maximum with one on top of the other If the machine is removed from the original packaging and is not used for some time ensure the wheels and drum are not in contact with the ground In this case use two supports at least 50mm in height to rest the machine on ensuring contact is with the base frame m WARNING This equipment is for dry use only and must not be used or kept outside in wet conditions Store the machine in a dry building otherwise the machine could be damaged Storage temperature from 20 C to 50 C Transporting and handling the mac
13. devono provvedere allo smaltimento delle apparecchiature da rottamare portandole al luogo di raccolta indicato per il riciclaggio delle apparecchiature elettriche ed elettroniche La raccolta e il riciclaggio separati dalle apparecchiature da rottamare in fase di smaltimento favoriscono la conservazione delle risorse naturali e garantiscono che tali apparecchiature vengano rottamate nel rispetto dell ambiente e della tutela della salute Per ulteriori informazioni sui punti di raccolta delle apparecchiature da rottamare contattare il proprio comune di residenza il servizio di smaltimento dei rifiuti locale o il negozio presso il quale e stato acquistato il prodotto Per indicare che questo prodotto comporta requisiti speciali di smaltimento e stata fissata un etichetta sul retro del gruppo manico inoltre essendo presente una fonte di alimentazione esterna ne e stata fissata un altra l etichetta sul retro della scocca della macchina Disposal of Waste Equipment by Users in Private Households in the European Union This symbol on the product on or its packaging indicates that this product must on be disposed of with your other household waste Instead it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensu
14. dures Before sanding check drum operation on the work surface The diagram shows the two possible cases OK drum and wheels are parallel to the surface to be sanded and the mark left by the drum is the total drum length approx 200mm NO the drum does not rest fully on the surface and only sands at one part emphasising marking on the floor In this case the drum and wheels must be positioned parallel to the surface to be sanded by varying the height of the cam wheel To adjust proceed as follows Turn the machine over m With the tool provided with the machine check how much the fixed wheel protrudes Loosen the nut pos 16 fig F Turn the cam pin fig F and raise lower the cam wheel until the wheel protrudes such that the drum operates in parallel to the surface to be sanded 5 Lock the nut pos 16 fig F 21 ARIES User Manual march 2013 Edition Machine adjustment procedures To keep the machine in good working condition the following items must be checked and serviced regularly Hoover the sawdust chamber regularly Check the outer surface of the drum regularly Remove any dirt Remove dirt from the machine unit and wheels regularly Dirt may cause uneven sanding 22 ARIES User Manual march 2013 Edition Machine adjustment procedures Remove the bag and shake it well to remove sawdust Turn the bag inside out and wash it in the machine in cold
15. e parts Always use K amp T spare parts Failure to use K amp T spare parts or repairs adjustments carried out by unauthorised personnel will invalidate the guarantee and any resulting liability The machine must only be repaired by qualified personnel This electric equipment is compliant with the relevant safety legislation Repairs must be carried out by qualified personnel using K amp T spare parts otherwise the user may suffer serious injury 24 2500 hours 2500 hours 2500 hours 2500 hours 5000 hours 5000 hours ARIES User Manual March 2013 Edition Emergency situations for the user FAULTS Insufficient cutting Insufficient motor speed Scratched work surface Insufficient dust collection Motor does not start Scorching on work surface CAUSES Unsuitable or worn abrasive Insufficient drum pressure Insufficient belt tension Worn belt Insufficient tension due to Excessive cable length or unsuitable cross section Unstable connections Faulty capacitor Faulty motor Faulty abrasive Drum surface dirty or faulty Incorrect wheel adjustment Dust bag more than 173 full Dust bag dirty or with blocked pores Vacuum ducts and or obstructed pipes Faulty switch Faulty capacitor Insufficient voltage for unstable connections Faulty motor No power supply voltage Worn abrasive Excessive pressure on drum Abrasive too fine 25 SOLUTIONS Replace the abrasive Increase
16. gsrichtlinien gelten wurde auf der R ckseite der Griffgruppe ein Aufkleber angebracht Auperdem da eine externe Versorgung im Lieferumfang enthalten ist wurde ein anderes Aufkleber an der R ckseite der Kalotte angebracht limination des quipements usag s par les utilisateurs dans les foyers priv s au sein de l Union europ enne La pr sence de ce symbole sur le produit ou sur son emballage indique que vous ne pouvez pas vous d barrasser de ce produit de la m me fa on que vos d chets courants Au contraire vous tes responsable de l vacuation de vos quipements usag s et cet effet vous tes tenu de les remettre dans un point de collecte agr pour le recyclage des quipements lectriques et lectroniques usag s Le tri l vacuation et le recyclage s par s de vos quipements usag s permettent de pr server les ressources naturelles et de s assurer que ces quipements sont recycl s dans le respect de la sant humaine et de l environnement Pour plus d informations sur les lieux de collecte des quipements usag s veuillez contacter votre mairie votre service de traitement des d chets m nagers ou le magasin ou vous avez achet le produit Fixez la grande tiquette l arriere du produit pour signaler qu il doit tre vacu selon une proc dure particuliere Lorsqu une alimentation externe est fournie fixez la petite tiquette l arriere de celle ci 21 Lo Lu CM N Wi i
17. hine WARNING The machine is heavy therefore remove the motor and handle unit before it is transported Ask for assistance to transport the three parts The machine can be dismantled into three parts to facilitate transportation Suction tube Base frame with drum and handle unit Proceed as follows 1 Ensure the power supply cable is disconnected 2 Open the belt guard after unscrewing the screws from the mains and the machine with the tool provided ARIES User Manual march 2013 Edition Transporting and handling the machine 3 Loosen the belt tightener using the lever pos 2 fig A and remove the belts 4 Once the nut has been loosened pos 3 fig A turn it towards the inside of the machine until the hollow washers positioned on the motor support spindle come out of their support housings 5 Remove the motor and take it to the 6 After lowering the lever pos 4 fig A lift the tube work area pos 5 and release the bar pos 6 from the cylinder pos 8 au m x a 4 if ARIES User Manual march 2013 Edition Transporting and handling the machine 7 Loosen the handle pos 9 fig A and 8 Lift the base frame by clasping the front and back Bring remove the tube from its housing and the belt guard to the edge and take it to the work area bring it to the place of work When transporting the machine with two people proceed as follow
18. llowing harmonised standards Machine safety basic concepts general design principles Basic terminology EN ISO 12100 methodology Part 1 Machine safety basic concepts general design principles Technical principles and EN ISO 12100 specifications Part 2 Machine safety electrical machine equipment Part 1 General rules EN 60204 1 Safety of domestic equipment and similar General rules EN 60 335 1 Special standards for equipment to treat and clean flooring for industrial and general use EN 60 335 2 67 Electromagnetic compatibility EMC e Limits and methods in measuring the characteristics of radio interference in motorised or thermal domestic appliances and similar electric tools and similar electric devices EN 55014 1 e Part 3 Limits Section 2 Limits for the emission of harmonic currents equipment with input current lt 16 A per phase EN 61000 3 2 e Part 3 Limits Section 11 Limit of voltage fluctuations and flicker in low voltage power supply systems for equipment with rated current 16 A EN 61000 3 11 CASSOLNOVO PV 27 09 2012 place and date of issue Michela Caresana CHIEF EXECUTIVE OFFICER 26 ARIES User Manual March 2013 Edition Disposal Smaltimento di apparecchiature da rottamare da parte di privati nel Unione Europea Questo simbolo che appare sul prodotto o sulla confezione indica che il prodotto non deve essere smaltito assieme ad altri rifiuti domestici Gli utenti
19. ng sanding operations No sources of fire must be kept near the work area Poorly ventilated work areas may create an explosive environment when some combustible materials are present in the atmosphere such as solvents thinners alcohol fuel some paints wood dust or other combustible materials Floor sanding machines may cause various materials and fumes to ignite Read the manufacturer s instructions for each chemical product used and establish its combustibility Always keep the work area well ventilated Striking nails when sanding may generate an explosion or fire Always ensure all nails are sunk before sanding surfaces Serious damage may occur if the power supply circuit trips repeatedly or is undersized Have the fuses safety circuit and power supply line checked by an authorised electrician Performing maintenance and or repairing the machine when it is not fully disconnected from the power supply may cause death due to electrocution Disconnect the power supply before carrying out any maintenance and or repair work The use of this machine on a circuit which is not earthed may cause death due to electrocution Never disconnect or disable the earthing conductor Consult an electrician if the earth conductor is missing or it is suspected that the circuit is not Suitably earthed The use of this machine with a damaged power supply cable may cause electric shock Check the power supply cable regularly for damage such as splitting or
20. re that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local city office your household waste disposal service or the shop where you purchased the product To indicate that this product has special disposal requirements has attach the label to the back side of the handle group If an external power supply is included attach the small label to the back of the power supply Entsorgung von Ausschusselektrogeraten durch Benutzer in privaten Haushalten in der EU Dieses Symbol auf dem Produkt oder dessen Verpackung gibt an dass das Produkt nicht zusammen mit dem Restm ll entsorgt werden darf Es obliegt daher Ihrer Verantwortung das zum Verschrotten bestimmte Gerat an einer f r die Entsorgung oder Wiederverwertung von Elektroger ten aller Art entsprechenden Stelle abzugeben Die separate Sammlung und das Recycling Ihrer zur Entsorgung bestimmten Elektrogerate tragt zum Schutz der Umwelt bei und gew hrleistet dass sie auf eine Art und Weise recycelt werden die keine Gefahrdung f r die Gesundheit des Menschen und der Umwelt darstellt F r weitere Informationen dar ber wo Sie alte Elektroger te zum Recyceln abgeben k nnen setzen Sie sich sie mit den rtlichen Beh rden Wertstoffh fen im Kontakt oder fragen Sie dort wo Sie das Gerat erworben haben Um darauf hinzuweisen dass f r dieses Produkt spezielle Entsorgun
21. s 1 One operator should clasp the handle grip and 2 the second holding the hub of the belt guide pos 1 fig A should lift the machine WARNING This equipment is not to be used by anyone children included with physical or mental disabilities or anyone without the relevant experience and knowledge unless they have received instructions on using the equipment and are supervised by a responsible person to ensure their safety Children must be supervised to ensure that they do not play with the machine ARIES User Manual march 2013 Edition Introduction This instruction manual should be read carefully before using the ARIES wood flooring sander for the first time The instruction manual contains important information on safety and preventing improper use of the machine and will resolve any doubts or questions making it possible to operate the machine safely and with ease Removing safety features could cause death or physical injury Familiarise yourself with the machine before using it for the first time If a situation arises which has not been described in this manual contact your retailer or Kunzle amp Tasin s r l The ARIES wood flooring sander is suitable for the dry sanding of wood floors Any other use without the consent of the manufacturer is prohibited Do not use on wet floors See Prohibited Uses on page 16 Keep hands and clothing away from moving mechanical parts The work area is protected via the base
22. socket does not match the plug consult a qualified electrician HAZARD If the machine is used with a damaged plug or power supply cable death may occur from electrocution If cables or plugs are worn or damaged in any way have them replaced by the manufacturer or the K amp T technical support service or similarly qualified person in order to prevent risks to safety Only use approved cables The maximum recommended cable length is 7m for greater lengths use cables with a larger cross section CAUTION Using the machine with unsuitable cable cross sections and or excessively long cables may cause injury or damage to people or objects WARNING The machine must never be moved using its cable and the cable must never be pulled when disconnecting from the socket WARNING Keep the cable away from sources of heat oil and sharp edges 11 ARIES User Manual March 2013 Edition Commencing operation WARNING MACHINE WITH 230V 50Hz 220V 60Hz SINGLE PHASE MOTOR For machines with a 230V 50Hz single phase motor Europe a HO5VV 3x2 5 mm HAR approved power supply cable must be used along with an approved 2P T 16A 200 250V plug HAZARD Sawdust can ignite spontaneously and cause injury or damage Empty the contents of the dust bag when it is 1 3 full Empty the dust bag at the end of each machine use Never leave the dust bag unattended when it contains sawdust Do not empty the contents of the dust bag above a fire Recommenda
23. sures and warnings Instructions on correct machine use Machine specifications Machine warnings Prohibited use Starting the machine Machine adjustment procedures Procedures for centring the abrasive belt Adjusting sanding pressure Wall edge castor Wheel adjustment on a surface parallel to the axis of the drum Routine maintenance to be performed Sawdust chamber for the user Drums for the user Wheels for the user Dust bag for the user Belt tension for the user Bearings only for Technical Support Service Drum pulleys and suction fan pulleys for the user Spare parts Emergency situations for the user Faults Causes Solutions Declaration of Conformity Disposal Diagrams Notes Oo oo ON M RR S N R A GOR PR OOINIVDIVDINI LIS SSO ss m a a nn NM a IIo ARIES User Manual march 2013 Edition Key for machine symbols READ THE INSTRUCTIONS CONTAINED IN THIS USER AND MAINTENANCE MANUAL BEFORE USING THE MACHINE HEARING PROTECTION DURING USE IS RECOMMENDED PROTECTION OF THE AIRWAYS DURING USE IS RECOMMENDED HAZARD DUE TO ELECTRICITY HAZARD DUE TO MOVING PARTS Operator safety instructions Failure to comply with HAZARD notices on the machine or in this HAZARD manual may result in death or serious injury to the operator or other people Read and comply with all HAZARD notices on the machine or in this manual WARNIN
24. tions on prevention measures for users WARNING Sawdust can spread through the air and be inhaled when using the sander Always wear a dust mask when using the sanding equipment WARNING The eyes and or body may suffer injury if personal safety clothing is not used Always wear safety goggles protective clothing and a dust mask during sanding operations WARNING Lengthy exposure to noise levels during sanding operations may damage the hearing Always use ear protectors during sanding operations CAUTION Never become distracted during sanding operations check what is happening continually Use common sense Do not use the machine when tired 12 ARIES User Manual March 2013 Edition HAZARD HAZARD HAZARD HAZARD HAZARD HAZARD HAZARD HAZARD HAZARD HAZARD HAZARD HAZARD Recommendations on prevention measures for users Using the machine when not fully assembled may cause injury or damage to people or objects Do not use the machine when it is not fully assembled Keep all fittings tightly closed Maintain machine settings in accordance with the specifications Using the sander without the safety guards and covers in position may cause injury or damage Always ensure that all safety guards and covers are in position and secured well The wood flooring sander may create an explosive environment Cigarettes cigars pipes lighters pilot flames or any other source of fire may create an explosion if lit duri
25. y cause injury or damage The machine must only be used to sand dry wooden floors which are level or have a maximum incline of 2 Do not use the machine to sand furniture Do not sit astride the machine when it is operating Work surfaces may be seriously damaged if the machine is left turning on one point while the tool is in contact with the surface To avoid damaging the surface approach the cutting line carefully Do not stop when lowering and raising the equipment keep moving at constant speed To start the machine proceed as follows i Become machine instructions notices operators manual that all read this with the 2 Arrange the dust bag as indicated by the yellow arrow and secure it with read all the cord safety Locate the power supply The socket must be compatible with the plug To avoid electrical hazards the socket must be earth protected with a 20 A fuse Wind the cable round the cable safety arm as shown in the photo at the side to keep it away from the path of the machine 16 ARIES User Manual march 2013 Edition Starting the machine 5 Open the side guard fig C 6 Lower the tensioning unit using the drum tensioning lever 7 Insert the abrasive belt ensuring it 8 Tension the drum using the drum tensioning lever protrudes approximately 2 mm from the rubber drum area but runs along the inside of the tensioning unit WARNING Only use 750x203 mm abrasive belts
Download Pdf Manuals
Related Search