Enginuity GB-102 Two Wire Test Set with Signaling
Contents
1. ON battery pack e Extended temperature Li ION Battery 1251 Nagel Blvd Batavia IL 60510 1 630 761 1892 Enginuity communications GB 1 02 Signaling 7 13 3 27 07 PM v 2 wire Signaling v 300 ohm Station LS G5 00 PPRT CO LS GS DID DID wini 3 Grate DLE lt Vi gt Sample PDA receive DTMF DP Gap 1004 Hz 0 0 dBm Screen Yo m Y Tip Ring 45 7Vde 0 00 mA Specifications Signaling Impedance 900 ohm Emulation CO Station PBX Modes LS GS DID immediate DID Wink Digits DTMF MF and DP CO Source 48 1vDC CO output Dial Tone amp RING 2RENLine Voltage 0 to 95v 1 5vDC Line Current 3 to 80 1 0mA Timing Pre Wink Pre Digit Wink Delay amp Delay Answer Delay All measurements 2mS Display Current Signaling State VoiceBand Receiver Interface 2 wire 600 900 1200 ohms impedance Level 3 to 40 or 0 4dBm Frequency 300 to 3400 2 Hz Noise measurement in PBX Modes 93 to lt 18 dBrn Voltage 0 to 95v 1 5vDC Current 3 to 80 1 0mA DTMF 0 to 25dBm 9dBT gt 45mS MF 1 to 24dBm 6dBT gt 25mS VoiceBand Transmitter Interface 2 wire 600 900 1200 ohm impedance Level 1 to 50 0 4dBm Frequency 300 to 3400 2 Hz Voltage Output 48v 1 vDC CO mode Current Output limited to 20 1 5 mA DTMF 0 dBm 2cB Twist 75 1 mS MF 6 dBm 1 dB Twist 75 1 mS Wink 250 or 2 mS Specifications subject to change without notice 6 06 Enginuity Co2. enainui Eng Inu FEY communications GB 102 Enginuity GB 102 Two Wire Test Set with Signaling The Enginuity GB 102 2 Wire Test Set with Signaling functions provides an intuitive Graphical User Interface GUI for the user to a Palm PDA or a PC Laptop computer The GB 102 DSO signaling mode emulates a PBX FXS or Station or CO FXO or Far End for complete voice call processing Use any Butt set or telephone to take or originate calls In FXS PBX Station modes the test set provides battery and rings the phone on incoming calls Received digits are captured and displayed on the graphical user interface The GB 102 provides the following features and capabilities e Palm PDA or PC Laptop Graphical User Interface GUI with one touch operation e CO and Station PBX emulation e Loop Start LS Ground Start GS Direct Inward Dialing DID Immediate and WINK modes or E amp M Signaling e Internal 48vDC Battery Ringing and Dial tone generation DTMF MF and DP e 2 wire 600 900 1200 ohm termination e Generate tones and measure frequency level and noise e Measure line voltage and current e Built in speaker for audible monitoring e Upgradeable to 2 4 Wire TIMS w Signaling e Upgradeable to Include DS1 Enginuity Communications Inc Front View GB 102 With carrying case e Hand held unit with padded carrying case e Built in On Line Help amp Tips Guide e Interactive User manual e AC DC adapter charger e Li I
3. mmunications Inc 1251 Nagel Blvd Batavia IL 60510 Power Input Power 100 to 120 volts AC 7 2 V Li ION Battery pack provides 4hrs continuous operation up to 10 hrs on full charge Mechanical Size 1 6 x 3 7 x 9 Weight Approximately 1 2 pounds Environmental Operating Temperature 0 to 50 C Storage Temperature 20 to 70 C Humidity 4 to 90 non condensing Ordering Information When ordering a Signaling Transmission Impairment Measuring System TIMS specify model Enginuity GB 102 Enginuity Upgrade to GB104 Eng QST U4WB Enginuity Upgrade to include DS1 ENG QST UDS1 Enginuity Communications is a developer and supplier of innovative transmission products and test equipment for operating telephone companies including SLC5 and D4 channel units and NCTE units For more information about fine Enginuity Communications products visit our web site at www EnginuityCommunications com or contact your nearest Enginuity Regional Sales Office or Enginuity Customer Service at 1 800 980 ECOM 1 630 761 1892
Download Pdf Manuals
Related Search