View
Contents
1. WWW LIGHTEMOTION COM AU RAZORTRI 2X 8 W QUAD LED effect light User s instruction manual This manual contains important information about the safe installation and use of this product Please read this instruction manual carefully before installing or operating Please keep these instructions in a safe place for future reference www lightemotion com au Congratulations on the purchase of your RAZORTRI by Light Emotion We are confident that you will be satisfied with your purchase We have prepared this manual to assist you with the operation of this item CONTENTS SECTION Page WHAT IS INCLUDED SAFETY INSTRUCIONTS 2 INSTALLATION POWER FUSE 3 OPERATION 4 SPECIFICATIONS 5 Please note that as part of out ongoing commitment to continuous improvement and product development the specifications in this manual are subject to change without notice Whilst every care has been taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement WHAT IS INCLUDED e Ix RAZORTRI e 1x Warranty Card e Ix User Manual SAFETY INSTRUCTIONS Please read these instructions carefully It includes important information about the installation usage and maintenance of this product e Please keep this User Manual for future consultation If you sell the unit to another user be sure that they also receive this instruction booklet e Always make sure that you are connecting to2. n then use UP and Down button to adjust the sound sensitivity level from 00 99 DMX Press Mode button till Add to set the DMX mode then use UP and DOWN button to set up DMX address from 001 512 DMX chart po Channel Chanel 22 Channel3 Function 000 LED stays on 000 255 Step motor Slow to 001 255 fast Strobe Slow to fast 251 155 Sound Active mode with random 000 255 to set up N L color sound sensitivity SLA 1 Set up the master unit on DMX mode or Sound active mode 2 Set up the slave unit on Slave mode press the Mode button till SLA to set slave mode 3 Use the DMX cable to link them together SPECIFICATIONS Lens 16pcs Mode DMX Sound active Master slave Power input AC 110 240V 50Hz 60Hz Power Consumption 90W Fuse F2A 250V Weight 4 6 Kg Size 340 X 370 X 285 mm LED 1x8W Quad RGBW 1x8W Quad RGBA Number of DMX channels 3 DMX512 connection 3 pin XLR Sound control via built in microphone Number of LEDs 2 Beam angle 100 Maximum ambient temperature Ta 45 C Maximum housing temperature Tc 50 C Min distance from flammable surfaces 0 5 m Min distance to lighted object 0 1 m
3. s for hanging the lighting effect e Use a safety wire with a breaking strain of more than double the lighting effect e This lighting effect can get extremely hot e Make sure the lighting effect has suitable ventilation as per the instructions below e This lighting effect is intended for indoor use only Never look directly into the light source To avoid electrical shock keep away from rain and moisture e Keep unit out of reach from children NOTE Use washers and spring washers when attaching your hook clamp to the yoke 1 For installation of the hook clamp and safety wire 2 This lighting effect must be 0 5m away from any flammable materials or any walls or ceilings Light Emotion has various hook clamps and safety wire suitable for your Blazer Please contact your local dealer for more information Not included POWER CAUTION This lighting effect is designed to operate on 240VAC Fuse M205 2A fast blow FUSE CAUTION Only use the correct fuse as specified on the rear panel of the lighting effect Disconnect the lighting effect from the mains before attempting to replace the fuse To replace the fuse please follow the following steps 3 1 Remove the fuse holder cover with a screwdriver 2 Remove existing fuse 3 Fit new fuse 4 Refit the fuse holder OPEARATION Unit has 3 buttons LED control panel Sound active mode Press the Mode button till SoU to set the Sound active control functio
4. the proper voltage and that the line voltage you are connecting to is not higher than that stated on the rear panel of the fixture e This product is intended for indoor use only To prevent risk of fire or shock do not expose fixture to rain or moisture e Make sure there are no flammable materials close to the unit while operating e The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surface Be sure that no ventilation slots are blocked e Always disconnect from power source before servicing or replacing fuse and be sure to replace with same fuse source e Secure fixture to fastening device using a safety chain e Maximum ambient temperature is 40 C Do not operate fixture at temperatures higher than this e In the event of serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center e Never connect the device to dimmer pack e Make sure power cord is never crimped or damaged e Never disconnect power cord by pulling or tugging on the cord e Never carry the fixture directly from the cord Always use the hanging mounting bracket e Avoid direct eye exposure to the light source while it is on INSTALLATION CAUTION e For safe mounting read the following instructions carefully e Use a suitable hook clamp
Download Pdf Manuals
Related Search
View view from my seat view your deal viewsonic viewpoint view advanced system settings viewrail viewer view from the wing view of star fields viewpoint spectrum viewpoint vista view local services viewfinder viewpoint school view clipboard history view network connections viewsonic monitor viewpoint login view devices and printers view pc name view clipboard view your deals from the view view instagram stories anonymously viewtrip view your deal on the view today