CB12 - Xantech.com
Contents
1. unshielded OK Z 286M Mero Link gt 7 cota Fig 3 The CB12 used as a Break Out Block NOTE Be sure the power supplies in any of these systems are plugged into an un switched AC outlet This maintains the system in stand by operation so that power on commands can be sent to the controlled equipment 8 30 00 eS teh ee CS M2. Ses INSTALLATION INSTRUCTIONS CB 12 CONNECTING BLOCK The Model CB12 provides a low cost means of connecting Xantech Quick Connect IR Receivers and standard 3 wire IR Receivers to one single or one dual emitter and a power supply in an infrared repeater system FEATURES AND SPECIFICATIONS e Inputs 1 IRRCVR 3 5mm stereo minijack Accepts any Xantech IR Receiver equipped with a 3 5mm stereo mini plug such as the 291 series or 490 30 1 Three terminal VGS block for wired connection of Xantech IR Receivers and SmartPad keypads e Output 1 Emitter OUT port 3 5mm mono mini jack e Model 282 283 284 amp 286 Xantech series Mini Emitters may be used e 2 1mm coaxial power jack for Xantech 781RG or 782 00 Power Supplies e Dimensions 2 1 8 x 1 1 4 x 3 4 CAUTION Plug only Xantech IR Receivers equipped with a stereo mini plug into the IR RCVR jack Do not plug emitters or other devices into this jack to do so may damage emitters and power supplies INSTALLATION 001 Fig 2 illustrates a typical in IR Receiver stallation using the CB12ina Hand Held Remote _ uU A j O c Fig 1 Model CB12 Connecting Block multiroom IR repeater sys EONA EE tem In this case a Xantech 780 10 291 Hidden Link IR Re Satelite Receiver 781RG one mR Recover a Power Supply Conductor Cable with Quick Connect Mini Plug ceiver is used to control a Satel
3. lite Receiveranda VCR in a cabinet behind closed VCR ineiitched 5 doors in Room 1 Controlof C the same equipment is ac Model 286M complished from two other Mouse Emitter 2 yE mE rooms with a Xantech 780 10 le Q IR RCVR J box IR Receiver and a E Smart Pad keypad by us CB12 Connecting Bock YS Mounted Behind o e ing the 3 terminal VGS con EE aaa A nector on the CB12 V 12Volts G Gnd S IR Signal When connecting a system follow this diagram carefully When you use more than 1 keypad and one IR receiver together in a system use the high current power supply model 782 00 in place of the 781RG Fig 2 The CB12 in a Typical 3 Room IR Repeater System ee teh E o M 0 Q q 0 o p 0 0 J J 0 0 ai J Ce D 0 0 A 0 The OUT port can drive any of the Xantech emitter models in the 282 283 284 and 286 series as well as the 286M shown in Fig 2 NOTE Be sure the Power Supplies in any of these systems are plugged into an unswitched AC outlet This maintains the system in stand by operation so that power on commands can be sent to the controlled equipment INSTALLATION cont d Fig 3 illustrates another application of the CB12 In this case it serves as a break out block for the convenient connection of a 291 IR Receiver to a 3 conductor room to room cable in a larger multiroom system You may also use it with any other Xantech quick c
4. onnect IR Receiver such as the 490 30 for the same purpose INSTALLATION NOTES 1 When used as a break out block you do not need to connect a power supply to the PWR jack on the CB12 Power is supplied on the 3 conductor cable coming from the connecting block in the equipment room Also do not plug an emitter into the OUT jack in this case To do so will prevent operation of the emitters in the equipment room 2 When paralleling IR receivers a maximum of 12 is recommended More than this may result in unreliable operation due to the buildup of IR noise 3 The Smart Pad keypads may be paralleled in larger numbers They are not subject to the IR noise limitation 4 Mounting The CB12 may be mounted on any flat surface using the double sided adhesive tape supplied ROOM 2 ROOM 3 CaO GND 3 Wire i Cabl 291 IR Receiver JOT D ra ADE 480 00 et no o Dinky Link Hand Held Remote IR Receiver 780 10 XK red J Box Stripe eee IR Receiver a Al IR OUT GND PTA cae IF T 120 vac Satellite Receiver So eo 782 00 ise 209 Smart Pad Power 282M OO OD Supply l OO OO Mouse Emitter 789 44 Wen Connecting Block 5 lt O OQ 7 2000 z 7 r 282M E 9 Emitter as f AV Receiver ee sO a P eal D llau gy m Senne EE y S IRIN ao a x ko E 283M 3 Conductor Room to Room Cable Q Blink IR Emitter a 25 D 24 to 18 gauge
Download Pdf Manuals
Related Search