R0E5563NEDMB01 User`s Manual (Debugging MCU Board for 100
Contents
1. 5 Connection To connect this product and the user system follow the procedure below The ROESS563NEDMBO01 this product can be used for debugging and on board evaluation in common by mounting the NQPACK100SD ND on the user system T For debugging Mount the NQPACK100SD ND on the user system Be sure to check that the location of pin 1 is correct 2 Install the YQPACK100SD after checking for a match with the position of pin 1 for the NQPACK100SD ND Then use the YQ GUIDE S1 to affix the YQPACK100SD to the NQPACK100SD ND e Do NOT use the screws included with the YQPACK100SD for fixing the YQPACK100SD e Do NOT use the screwdriver included with the NQPACK100SD ND for fixing the YQ GUIDE S1 That is used only for the HQPACK100SD Note that you need to provide your own screwdriver 3 Connect the ROESS563NEDMBO01 after checking for a match with the position of pin 1 for the YQPACK100SD 4 Install the connector of the flexible cable from the E20 emulator to the 38 pin connector on the ROE5563NEDMBO01 Hold the ROESS563NEDMBO01 while connecting the cable to avoid imposing heavy pressure on the 38 pin connector of the ROE5563NEDMBO1 2 For on board evaluation 5 Mount an MCU with on chip flash memory and the HQPACK100SD not included in order on the NQPACK100SD ND on the user system User s Manual 1 For debugging Flexible cable of the E20 emulator ROES563NEDMB01 R0E5563NEVKZ00 connector DA E R0E552. GUIDE S1 becomes significantly greater than that required at the start of tightening Tightening a screw too much may break the screw hole of the NQPACK or lead to a faulty connection by cracking solder on the NQPACK side e Failure of conduction during operation may be due to a crack in the solder for the NQPACK Check conduction with a tester and re solder the NQPACK as required R20UT2221EJ0200 Rev 2 00 Mar 05 2014 7tENESAS Page 4 of 8 ROES563NEDMB01 6 Dimensions of This Product Figures 4 shows the dimensions and reference foot pattern of this product ROESS563NEDMBO01 User s Manual 50 00 TP1 TP2 TP3 TP4 TP5 VREFHO AVCCO VREFH vVBATT VCC_USB z i oo a uw lt gt D ojo O m 6 113 00 13 00 25 00 0 50x24 12 00 lt _ o pata ie j i ol o i oO O o _ 0 50 en gt m 13 00 17 00 Unit mm Figure4 Reference Foot Pattern and Dimensions of This Product R0E5563NEDMB01 R20UT2221EJ0200 Rev 2 00 Mar 05 2014 RENESAS Page 5 of 8 ROE5563NEDMB01 User s Manual 7 Notes on Usage READ the following warnings before using this product Incorrect operation will damage this product and the user system The USER PROGRAM will be LOST Notes on Connecting the Debugging MCU Board e Cables must not be connected or removed while the power is on e Before connecting this product and th
3. back end of life equipment register for this service at http www renesas eu weee Cautions to Be Taken for Handling This Product Q e Take full care not to touch any parts or cause short circuits on this product e Protect this product from excessive physical shock Do not alter this product If any alteration is attempted this product will no longer be supported e The MCU installed on this product is only for use in debugging Do not remove the MCU from the board to use it for other purposes e For purchasing the NQPACK100SD ND YQPACK100SD and HQPACK100SD contact the following Tokyo Eletech Corporation http www tetc co jp e_index htm Cautions to Be Taken for Turning On the Power Do not apply a power voltage that is beyond the range guaranteed for the MCU e Only supply power to this product and connected parts after having connected all cables Caution for Use Temperature This product is to be used in an environment with a maximum ambient temperature of 35 C Care should be taken that this temperature is not exceeded European Union regulatory notices This product complies with the following EU Directive Environmental Compliance and Certification e Waste Electrical and Electronic Equipment WEEE Directive 2012 19 EC R20UT2221EJ0200 Rev 2 00 Page 2 of 8 Mar 05 2014 RENESAS ROE5563NEDMB01 User s Manual 3 Specifications Table 2 shows the functional specifications of this product Table2 Sp
4. for flash writing e g writing the on chip flash memory mode of High performance Embedded Workshop do not use the mode Note on the A D Converter e The characteristics of the A D converter differ from those of actual MCU because there are a converter board and other devices between the MCU and the user system Note on the Hot Plug in Function e Do not use the hot plug in function when using this product Note on the Use of a Low CL Crystal Resonator for the Sub clock Oscillator e Note that the longer sub clock wiring pattern resulting from the use of this product may cause a failure in sub clock oscillation or affect the oscillating accuracy Note on Communication Interface e Use this product via JTAG communication R20UT2221EJ0200 Rev 2 00 Page 6 of 8 Mar 05 2014 RENESAS ROE5563NEDMB01 User s Manual Precautions This product is only intended for use in a laboratory environment under ambient temperature and humidity conditions A safe separation distance should be used between this and any sensitive equipment Its use outside the laboratory classroom study area or similar such area invalidates conformity with the protection requirements of the Electromagnetic Compatibility Directive and could lead to prosecution The product generates uses and can radiate radio frequency energy and may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a parti
5. 630EPFK20 back side YQSOCKET100SDF Use a flat bladed 3 screwdriver z YQ GUIDE S1 x4 l YQPACK100SD in SR NQPACK100SD ND 2 For on board evaluation HQPACK100SD not included J 100 pin 0 5mm pitch I PLQP0100KB A foot pattern acs Ta indicates pin 1 in this example Check that the pin 1 positions on the foot pattern and all of the components are correctly aligned Figure 3 Product Before using the ROESS63NEDMBO01 be sure to read section 7 Notes on Usage Warnings to Be Taken for Connection Connections of the User System and This e Always switch OFF the emulator this product and the user system before connecting or disconnecting the emulator Failure to do so will create a FIRE HAZARD and will damage the emulator this product and the user system e Make sure that the connectors on both ends of the user system interface cable are facing the right way relative to the user side connector on the emulator and the 38 pin connector on this product respectively Incorrect connection will create a FIRE HAZARD and will damage the emulator this product and the user system CAUTION Cautions to Be Taken for Mounting the NQPACK e Check the locations of pin 1 before mounting the NQPACK e The tightening torque must be no greater than 0 054 Nem If the applied torque is not accurately measurable stop tightening when the force required to turn the screw YQ
6. Fax 65 6213 0300 Renesas Electronics Malaysia Sdn Bhd Unit 906 Block B Menara Amcorp Amcorp Trade Centre No 18 Jin Persiaran Barat 46050 Petaling Jaya Selangor Darul Ehsan Malaysia Tel 60 3 7955 9390 Fax 60 3 7955 9510 Renesas Electronics Korea Co Ltd 12F 234 Teheran ro Gangnam Gu Seoul 135 080 Korea Tel 82 2 558 3737 Fax 82 2 558 5141 sentences are ignored the equipment may cause All trademarks and registered trademarks are the property personal injury or damage to the products of their respective owners A c o If the requirements shown in the CAUTION Renesas Tools Website _ http www renesas com tools 2012 2014 Renesas Electronics Corporation and Renesas Solutions Corp Colophon 3 0
7. ROE5563NEDMBO01 R20UT2221EJ0200 Rev 2 00 Debugging MCU Board for 100 pin 0 5mm pitch LQFP Mar 05 2014 of the RX63N and RX631 Groups 1 Overview The debugging MCU board ROES563NEDMBO1 hereafter referred to as this product is for MCUs of the RX63N and RX631 groups in the PLQP0100KB A package With the E20 emulator the emulator occupies some user port pins for controlling the emulator and output of trace information These user port pins must be connected with a 38 pin connector installed on the user system With this product however all user port pins are available for the user system In addition you do not need to install a 38 pin connector on the user system Figure 1 shows the configuration of a system that includes this product and the E20 Be sure to read section 7 Notes on Usage before using this product E20 emulator Debugging MCU board USB interface cable this product l it YQPACK 38 pin connector provided with this roduct User system NQPACK provided with this product Host computer Figure 1 System Configuration 2 Package Components The package of this product consists of the following items Check that you have all of the components when you unpack the box Table 1 Package Components Quantity Remarks 1 For the dimensions refer to section 6 Dimensions of This Product Converter board ROE55630EPFK20 For the dimensions refer to section 6 D
8. ault or damage is raised by any one of the following causes the warranty is void a Misuse or abuse of the product or its use under other abnormal conditions b Improper handling of the product after purchase such as dropping of the product when it is transported or moved c Other pieces of equipment connected to the product d Fire earthquakes thunderbolts floods or other natural disasters or abnormal voltages etc e Modifications repairs adjustments or other acts made to the product by other than Renesas Electronics Corporation In the above cases contact your local distributor If your product is being leased consult the leasing company or the owner R20UT2221EJ0200 Rev 2 00 Page 7 of 8 Mar 05 2014 RENESAS Notice 1 Descriptions of circuits software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples You are fully responsible for the incorporation of these circuits software and information in the design of your equipment Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits software or information 2 Renesas Electronics has used reasonable care in preparing the information included in this document but Renesas Electronics does not warrant that such information is error free Renesas Electronics assumes no liability whatsoever for any damages
9. certain use conditions Further Renesas Electronics products are not subject to radiation resistance design Please be sure to implement safety measures to guard them against the possibility of physical injury and injury or damage caused by fire in the event of the failure of a Renesas Electronics product such as safety design for hardware and software including but not limited to redundancy fire control and malfunction prevention appropriate treatment for aging degradation or any other appropriate measures Because the evaluation of microcomputer software alone is very difficult please evaluate the safety of the final products or systems manufactured by you 8 Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances including without limitation the EU RoHS Directive Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations 9 Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture use or sale is prohibited under any applicable domestic or foreign laws or regulations You should not use Renesas Electronics products or technology described
10. cular installation If this equipment causes harmful interference to radio or television reception which can be determined by turning the equipment off or on you are encouraged to try to correct the interference by one or more of the following measures e ensure attached cables do not lie across the equipment e reorient the receiving antenna e increase the distance between the equipment and the receiver e connect the equipment into an outlet on a circuit different from that which the receiver is connected e power down the equipment when not in use e consult the dealer or an experienced radio TV technician for help NOTE It is recommended that wherever possible shielded interface cables are used The product is potentially susceptible to certain EMC phenomena To mitigate against them it is recommended that the following measures be undertaken e The user is advised that mobile phones should not be used within 10m of the product when in use e The user is advised to take ESD precautions when handling the equipment This product does not represent an ideal reference design for an end product and does not fulfill the regulatory standards for an end product 8 Warranty 1 This product comes with a one year warranty after purchase Should the product break down or be damaged while you re using it under normal condition based on its user s manual it will be repaired or replaced free of cost 2 Note however that if your product s f
11. e user system check that the pin locations on both sides are correctly aligned with each other Note on Rewriting the Flash Memory e The number of times that the flash memory in the MCU installed on this product can be programmed is limited If an error in erasure occurs during debugging replace this product Notes on Debugging e This product is only usable for debugging when it is connected to the user system e Debugging by this product alone is not supported Notes on Starting the Debugger and Selecting the MCU Type e Select the MCU type for use in the device name section of the Initial Settings dialog box on initiation of the debugger Note on Differences between the MCU to be Debugged and This Product e The ROM size of the MCU installed in this product is 2MB Note that if the ROM size of the MCU to be debugged is smaller than that of this product access can be made to the differential area Notes on Designing the User System e Pull the levels on the EMLE pin down to 4 7 kQ to 10 kQ e Pull the levels on the MD pin up to 4 7 kQ to 10 kQ and select the single chip mode e The output of the reset circuit of the user system must be open collector Note on the Flash Programming Software Products Flash Development Toolkit Renesas Flash Programmer etc e Do not use the flash programming software products when using this product Note on the Writing the On chip Flash Memory Mode e Ifthe debugger has an exclusive mode
12. ecifications of This Product Item Specification MCU for use eRX63N and RX631 group MCUs in PLQP0100KB A packages The MCU type name eR5F563NEDDFC installed on this product ROM 2 Mbytes RAM 128 Kbytes E2 Data Flash 32 Kbytes Power supply ePower VCC AVCCO VREFH VCC_USB at 2 7 to 3 6 V is supplied from the user system ePower VREFHO0 at 2 7 to AVCCO is supplied from the user system ePower VBATT at 2 3 to 3 6 V is supplied from the user system eThe state of power supply can be monitored through the test pins TP1 for VREFHO TP2 for AVCCO TP3 for VREFH TP4 for VBATT TP5 for VCC_USB TP6 for VCC and TP7 for GND System clock EXTAL e4 to 16 MHz clock signals are supplied from the user system Sub clock XCIN 32 768 kHz clock signals are supplied from the user system Note 1 Use this product at a voltage VCC gt Vpor that doesn t make the MCU enter the state of power on reset 4 Reset Circuit Figure 2 shows the reset circuit with the level on the RES pin pulled up by a 510 kQ resistor ROES563NEVKZ00 ROES55630EPFK20 38 pin connector CN3 A MCU IC1 YQSOCKET100SDF IC1 Pin 10 RES Pin 9 RES Notes 1 The number indicated is the pin number of the 38 pin connector CN3 2 The number indicated is the pin number of the YQSOCKET100SDF IC1 Figure 2 Reset Circuit R20UT2221EJ0200 Rev 2 00 Page 3 of 8 Mar 05 2014 RENESAS ROES563NEDMB01
13. imensions of This Product YQPACK100SD Connector to be placed between this product and the NQPACK from Tokyo Eletech Corporation NQPACK100SD ND IC socket for mounting on the user system from Tokyo Eletech Corporation YQ GUIDE S1 Screws for fastening the YQPACK to the NQPACK from Tokyo Eletech Corporation Cautions in handling 1 Cautions when handling the products of Tokyo Eletech Corporation User s Manual English and Japanese 1 for each This manual English Note NQPACK YQPACK YQSOCKET YQ GUIDE HQPACK TQPACK TQSOCKET CSSOCKET CSPLUGMW and LSPACK are trademarks of Tokyo Eletech Corporation R20UT2221EJ0200 Rev 2 00 Page 1 of 8 ROE5563NEDMB01 User s Manual Important CAUTION Caution to Be Taken for Disposal Q Penalties may be applicable for incorrect disposal of this waste in accordance with your national legislation European Union regulatory notices The WEEE Waste Electrical and Electronic Equipment regulations put responsibilities on producers for the collection and recycling or disposal of electrical and electronic waste Return of WEEE under these regulations is applicable in the European Union only This equipment including all accessories is not intended for household use After use the equipment cannot be disposed of as household waste and the WEEE must be treated recycled and disposed of in an environmentally sound manner Renesas Electronics Europe GmbH can take
14. in this document for any purpose relating to military applications or use by the military including but not limited to the development of weapons of mass destruction When exporting the Renesas Electronics products or technology described in this document you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations 10 It is the responsibility of the buyer or distributor of Renesas Electronics products who distributes disposes of or otherwise places the product with a third party to notify such third party in advance of the contents and conditions set forth in this document Renesas Electronics assumes no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics products 11 This document may not be reproduced or duplicated in any form in whole or in part without prior written consent of Renesas Electronics 12 Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products or if you have any other inquiries Note 1 Renesas Electronics as used in this document means Renesas Electronics Corporation and also includes its majority owned subsidiaries Note 2 Renesas Electronics product s means any product developed or manufactured by or for Renesas Electronics 2 CENESAS SALES OFFICES Renesas Elect
15. incurred by you resulting from errors in or omissions from the information included herein 3 Renesas Electronics does not assume any liability for infringement of patents copyrights or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document No license express implied or otherwise is granted hereby under any patents copyrights or other intellectual property rights of Renesas Electronics or others 4 You should not alter modify copy or otherwise misappropriate any Renesas Electronics product whether in whole or in part Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from such alteration modification copy or otherwise misappropriation of Renesas Electronics product 5 Renesas Electronics products are classified according to the following two quality grades Standard and High Quality The recommended applications for each Renesas Electronics product depends on the product s quality grade as indicated below Standard Computers office equipment communications equipment test and measurement equipment audio and visual equipment home electronic appliances machine tools personal electronic equipment and industrial robots etc High Quality Transportation equipment automobiles trains ships etc traffic control systems anti disaster systems anti crime systems and safet
16. ronics Corporation http Awww renesas com Refer to http www renesas com for the latest and detailed information Renesas Electronics America Inc 2880 Scott Boulevard Santa Clara CA 95050 2554 U S A Tel 1 408 588 6000 Fax 1 408 588 6130 Renesas Electronics Canada Limited 1101 Nicholson Road Newmarket Ontario L3Y 9C3 Canada Tel 1 905 898 5441 Fax 1 905 898 3220 Renesas Electronics Europe Limited Dukes Meadow Millboard Road Bourne End Buckinghamshire SL8 5FH U K Tel 44 1628 651 700 Fax 44 1628 651 804 Renesas Electronics Europe GmbH Arcadiastrasse 10 40472 D sseldorf Germany Tel 49 211 65030 Fax 49 211 6503 1327 Renesas Electronics China Co Ltd 7th Floor Quantum Plaza No 27 ZhiChunLu Haidian District Beijing 100083 P R China Tel 86 10 8235 1155 Fax 86 10 8235 7679 Renesas Electronics Shanghai Co Ltd Unit 301 Tower A Central Towers 555 LanGao Rd Putuo District Shanghai China Tel 86 21 2226 0888 Fax 86 21 2226 0999 Renesas Electronics Hong Kong Limited Unit 1601 1613 16 F Tower 2 Grand Century Place 193 Prince Edward Road West Mongkok Kowloon Hong Kong Tel 852 2886 9318 Fax 852 2886 9022 9044 Renesas Electronics Taiwan Co Ltd 13F No 363 Fu Shing North Road Taipei Taiwan Tel 886 2 8175 9600 Fax 886 2 8175 9670 Renesas Electronics gapore Pte Ltd 80 Bendemeer Road Unit 06 02 Hyflux Innovation Centre Singapore 339949 Tel 65 6213 0200
17. y equipment etc Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct threat to human life or bodily injury artificial life support devices or systems surgical implantations etc or may cause serious property damages nuclear reactor control systems military equipment etc You must check the quality grade of each Renesas Electronics product before using it in a particular application You may not use any Renesas Electronics product for any application for which it is not intended Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for which the product is not intended by Renesas Electronics 6 You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics especially with respect to the maximum rating operating supply voltage range movement power voltage range heat radiation characteristics installation and other product characteristics Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges 7 Although Renesas Electronics endeavors to improve the quality and reliability of its products semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under
Download Pdf Manuals
Related Search