R0E5571MLDMB01 User`s Manual Debugging MCU Board for 144
Contents
1. ROE5571MLDMB0O1 User s Manual 3 Specifications Table 2 shows the functional specifications of the debugging MCU board Table2 Specifications of the Debugging MCU Board Item Specification MCU for use eRX71M group MCUs in PLQP0144KA A packages The MCU type name e R5F571MLGDFU MCU dedicated for tools installed on the debugging ROM 4 Mbytes RAM 512Kbytes E2 Data flash 64 Kbytes MCU board Power supply ePower VCC AVCCO AVCC1 VCC_USB at 2 7 to 3 6 V is supplied from the user system ePower VREFH0 at 2 7 to AVCCO is supplied from the user system ePower VCC_USBHS AVCC_USBHS at 3 0 to 3 6 V is supplied from the user system ePower VBATT at 2 0 to 3 6 V is supplied from the user system System clock EXTAL e24 MHz clock signals max are supplied from the user system Note 1 Use the debugging MCU board at a voltage VCC gt Vpor that doesn t make the MCU enter the state of power on reset 4 Reset Circuit Figure 2 shows the reset circuit with the level on the RES pin pulled up by a 510 kQ resistor R0E5571MLVKZ00 R0E5571MLPFK00 38 pin connector CN3 MCU IC1 YQSOCKET144SDF IC1 Pin 19 RES Pin 9 RES Notes 1 The number indicated is the pin number of the 38 pin connector CN3 2 The number indicated is the pin number of the YQSOCKET144SDF IC1 Figure 2 Reset Circuit on the Debugging MCU Board R20UT2935EJ0100 Rev 1 00 Page 3 of 8 Mar 12. e The number of times that the flash memory in the MCU installed on the debugging MCU board can be programmed is limited If an error in erasure occurs during debugging replace the debugging MCU board Notes on Debugging e The debugging MCU board is only usable for debugging when it is connected to the user system e Debugging by the debugging MCU board alone is not supported Note on Starting the Debugger and Selecting the MCU Type e To make a new project in the IDE select a device type name you use And before debugging a program make settings as follows e When debugging with the CS IDE select File gt Add gt Add New Subproject to open a dialog and set the following to make a sub project for debugging only Using microcontroller ROE5571MLDMBxx Kind of project Debugging only Then change the debugging tool for the sub project to E20 and select an ABS file generated in the main project as a download file in property settings of the debugging tool After finishing the other settings select the sub project in the project tree panel and set the project to active by right clicking e When debugging with the e2 studio IDE select Run gt Debug Configurations to open a dialog and select the following in the Debugger tab Target Device ROE5571MLDMBxx Note on Communication Interface e Use this product via JTAG communication Note on Differences between the MCU to be debugged and the Debugging MCU Board e The ROM si
3. Debugging MCU Board Converter board ROES571MLPFKO0 For the dimensions refer to section 6 Dimensions of the Debugging MCU Board YQPACK144SD Connector to be placed between the debugging MCU board from Tokyo Eletech Corporation and the NQPACK NQPACK144SD ND IC socket for mounting on the user system from Tokyo Eletech Corporation YQ GUIDE S1 Screws for fastening the YQPACK to the NQPACK from Tokyo Eletech Corporation Cautions in handling Cautions when handling the products of Tokyo Eletech Corporation User s Manual English and Japanese 1 for each This manual English Note NQPACK YQPACK YQSOCKET YQ GUIDE HQPACK TQPACK TQSOCKET CSSOCKET CSPLUG W and LSPACK are trademarks of Tokyo Eletech Corporation R20UT2935EJ0100 Rev 1 00 Page 1 of 8 Mar 1 2015 RENESAS ROE5571MLDMBO0O1 User s Manual Important CAUTION Caution to Be Taken for Disposal Q Penalties may be applicable for incorrect disposal of this waste in accordance with your national legislation European Union regulatory notices The WEEE Waste Electrical and Electronic Equipment regulations put responsibilities on producers for the collection and recycling or disposal of electrical and electronic waste Return of WEEE under these regulations is applicable in the European Union only This equipment including all accessories is not intended for household use After use the equipment cannot be disposed of as hous
4. in the design of your equipment Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits software or information 2 Renesas Electronics has used reasonable care in preparing the information included in this document but Renesas Electronics does not warrant that such information is error free Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein 3 Renesas Electronics does not assume any liability for infringement of patents copyrights or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document No license express implied or otherwise is granted hereby under any patents copyrights or other intellectual property rights of Renesas Electronics or others 4 You should not alter modify copy or otherwise misappropriate any Renesas Electronics product whether in whole or in part Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from such alteration modification copy or otherwise misappropriation of Renesas Electronics product 5 Renesas Electronics products are classified according to the following two quality grades Standard and High Quality The recommended applications for each Renesas Electronics product de
5. regarding the information contained in this document or Renesas Electronics products or if you have any other inquiries Note 1 Renesas Electronics as used in this document means Renesas Electronics Corporation and also includes its majority owned subsidiaries Note 2 Renesas Electronics product s means any product developed or manufactured by or for Renesas Electronics CENESAS SALES OFFICES Renesas Electronics Corporation http www renesas com Refer to http www renesas com for the latest and detailed information Renesas Electronics America Inc 2801 Scott Boulevard Santa Clara CA 95050 2549 U S A Tel 1 408 588 6000 Fax 1 408 588 6130 Renesas Electronics Canada Limited 1101 Nicholson Road Newmarket Ontario L3Y 9C3 Canada Tel 1 905 898 5441 Fax 1 905 898 3220 Renesas Electronics Europe Limited Dukes Meadow Millboard Road Bourne End Buckinghamshire SL8 5FH U K Tel 44 1628 585 100 Fax 44 1628 585 900 Renesas Electronics Europe GmbH Arcadiastrasse 10 40472 Dusseldorf Germany Tel 49 211 6503 0 Fax 49 211 6503 1327 Renesas Electronics China Co Ltd ee o Room 1709 Quantum Plaza No 27 ZhiChunLu Haidian District Beijing 100191 P R China Tel 86 10 8235 1155 Fax 86 10 8235 7679 Renesas Electronics Shanghai Co Ltd a N Unit 301 Tower A Central Towers 555 Langao Road Putuo District Shanghai P R China 200333 Tel 86 21 2226 0888 Fax 86 21
6. 2015 RENESAS ROE5571MLDMBO1 5 Connection To connect the debugging MCU board and user system follow the procedure below The ROES571MLDMBO01 this product can be used for debugging and on board evaluation in common by mounting the NQPACK144SD ND on the user system 1 For debugging 1 Mount the NQPACK144SD ND on the user system Be sure to check that the location of pin 1 is correct 2 Install the YQPACK144SD after checking for a match with the position of pin 1 for the NQPACK144SD ND Then use the YQ GUIDE S1 to affix the YQPACKI144SD to the NQPACK144SD ND e Do NOT use the screws included with the YQPACK144SD for fixing the YQPACK144SD Do NOT use the screwdriver included with the NQPACK144SD ND for fixing the YQ GUIDE S1 That is used only for the HQPACK144SD Note that you need to provide your own screwdriver 3 Connect the ROES571MLDMBO1 after checking for a match with the position of pin 1 for the YQPACK144SD 4 Install the connector of the flexible cable from the E20 emulator to the 38 pin connector on the ROE5571MLDMBO1 Hold the ROE5571MLDMBO01 while connecting the cable to avoid imposing heavy pressure on the 38 pin connector of the ROE5571MLDMBO1 2 For on board evaluation 5 Mount an MCU with on chip flash memory and the HQPACK144SD not included in order on the NQPACK144SD ND on the user system User s Manual 1 For debugging Flexible cable of the E20 emulator ROE5571MLPFKOO back si
7. 2226 0999 Renesas Electronics Hong Kong Limited Unit 1601 1613 16 F Tower 2 Grand Century Place 193 Prince Edward Road West Mongkok Kowloon Hong Kong Tel 852 2265 6688 Fax 852 2886 9022 9044 Renesas Electronics Taiwan Co Ltd 13F No 363 Fu Shing North Road Taipei 10543 Taiwan Tel 886 2 8175 9600 Fax 886 2 8175 9670 Renesas Electronics Singapore Pte Ltd 80 Bendemeer Road Unit 06 02 Hyflux Innovation Centre Singapore 339949 Tel 65 6213 0200 Fax 65 6213 0300 Renesas Electronics Malaysia Sdn Bhd Unit 906 Block B Menara Amcorp Amcorp Trade Centre No 18 Jin Persiaran Barat 46050 Petaling Jaya Selangor Darul Ehsan Malaysia Tel 60 3 7955 9390 Fax 60 3 7955 9510 Renesas Electronics Korea Co Ltd 12F 234 Teheran ro Gangnam Ku Seoul 135 920 Korea Tel 82 2 558 3737 Fax 82 2 558 5141 If the requirements shown in the CAUTION Renesas Tools Website _http www renesas com tools CAUTION sentences are ignored the equipment may cause All trademarks and registered trademarks are the property personal injury or damage to the products of their respective owners 2015 Renesas Electronics Corporation Colophon 4 0
8. RO E5571 MLDMBO1 R20UT2935EJ0100 Rev 1 00 Debugging MCU Board for 144 pin 0 5mm pitch LFQFP Mar 1 2015 of the RX71M Group 1 Overview This product is for MCUs of the RX71M group in the PLQP0144KA A package With the E20 emulator the emulator occupies some user port pins for controlling the emulator and output of trace information These user port pins must be connected with a 38 pin connector installed on the user system With the debugging MCU board however all user port pins are available for the user system In addition you do not need to install a 38 pin connector on the user system And this product has faster trace output than when with an actual MCU so that it is possible to reduce dropping trace data Figure 1 shows the configuration of a system that includes the debugging MCU board and the E20 Be sure to read section 7 Notes on Usage before using the debugging MCU board E20 emulator Debugging MCU board USB interface cable this product U YQPACK 38 pin connector Y provided with this roduct User system NQPACK provided with this product Host computer Figure 1 System Configuration 2 Components Table 1 lists the components of the debugging MCU board Check that you have all of the components when you unpack the box Table 1 Components of the Debugging MCU Board Quantity Remarks 1 For the dimensions refer to section 6 Dimensions of the ROESS71MLVKZ00
9. de YQSOCKET144SDF Use a flat bladed 3 screwdriver YQ GUIDE S1 x4 2 For on board evaluation HQPACK144SD not included YQPACK144SD I eS MCU 5 144 pin 0 5 mm pitch PLQP0144KA A pad pattern indicates pin 1 in this example Check that the pin 1 positions on the foot pattern and all of the components are correctly aligned Figure 3 Connections of the User System and This Product Before using the ROESS71MLDMBOl1 be sure to read section 7 Notes on Usage Warnings to Be Taken for Connection e Always switch OFF the emulator this product and the user system before connecting or disconnecting the emulator Failure to do so will create a FIRE HAZARD and will damage the emulator this product and the user system Make sure that the connectors on both ends of the user system interface cable are facing the right way relative to the user side connector on the emulator and the 38 pin connector on this product respectively Incorrect connection will create a FIRE HAZARD and will damage the emulator this product and the user system N CAUTION Cautions to Be Taken for Mounting the NQPACK e Check the locations of pin 1 before mounting the NQPACK e The tightening torque must be no greater than 0 054 Nem If the applied torque is not accurately measurable stop tightening when the force required to turn the screw YQ GUIDE S 1 becomes significantly greater than that
10. ehold waste and the WEEE must be treated recycled and disposed of in an environmentally sound manner Renesas Electronics Europe GmbH can take back end of life equipment register for this service at http www renesas eu weee Cautions to Be Taken for Handling This Product Take full care not to touch any parts or cause short circuits on this product Protect this product from excessive physical shock Do not alter this product If any alteration is attempted this product will no longer be supported The MCU installed on this product is only for use in debugging Do not remove the MCU from the board to use it for other purposes For purchasing the NQPACK144SD ND YQPACK144SD and HQPACK144SD contact the following Tokyo Eletech Corporation http www tetc co jp e_index htm Cautions to Be Taken for Turning On the Power e Do not apply a power voltage that is beyond the range guaranteed for the MCU e Only supply power to this product and connected parts after having connected all cables Caution for Use Temperature This product is to be used in an environment with a maximum ambient temperature of 35 C Care should be taken that this temperature is not exceeded European Union regulatory notices This product complies with the following EU Directive Environmental Compliance and Certification e Waste Electrical and Electronic Equipment WEEE Directive 2012 19 EU R20UT2935EJ0100 Rev 1 00 Page 2 of 8 Mar 1 2015 RENESAS
11. eristics installation and other product characteristics Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges 7 Although Renesas Electronics endeavors to improve the quality and reliability of its products semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions Further Renesas Electronics products are not subject to radiation resistance design Please be sure to implement safety measures to guard them against the possibility of physical injury and injury or damage caused by fire in the event of the failure of a Renesas Electronics product such as safety design for hardware and software including but not limited to redundancy fire control and malfunction prevention appropriate treatment for aging degradation or any other appropriate measures Because the evaluation of microcomputer software alone is very difficult please evaluate the safety of the final products or systems manufactured by you 8 Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances including without limitation the EU RoHS Directi
12. ill the regulatory standards for an end product 8 Warranty 1 This product comes with a one year warranty after purchase Should the product break down or be damaged while you re using it under normal condition based on its user s manual it will be repaired or replaced free of cost 2 Note however that if your product s fault or damage is raised by any one of the following causes the warranty is void a Misuse or abuse of the product or its use under other abnormal conditions b Improper handling of the product after purchase such as dropping of the product when it is transported or moved c Other pieces of equipment connected to the product d Fire earthquakes thunderbolts floods or other natural disasters or abnormal voltages etc e Modifications repairs adjustments or other acts made to the product by other than Renesas Electronics Corporation 3 The expendable supplies socket adapter etc are not included in the objects to be repaired In the above cases contact your local distributor If your product is being leased consult the leasing company or the owner R20UT2935EJ0100 Rev 1 00 Page 7 of 8 Mar 1 2015 RENESAS Notice 1 Descriptions of circuits software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples You are fully responsible for the incorporation of these circuits software and information
13. lidates conformity with the protection requirements of the Electromagnetic Compatibility Directive and could lead to prosecution The product generates uses and can radiate radio frequency energy and may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment causes harmful interference to radio or television reception which can be determined by turning the equipment off or on you are encouraged to try to correct the interference by one or more of the following measures e ensure attached cables do not lie across the equipment reorient the receiving antenna increase the distance between the equipment and the receiver connect the equipment into an outlet on a circuit different from that which the receiver is connected power down the equipment when not in use e consult the dealer or an experienced radio TV technician for help NOTE It is recommended that wherever possible shielded interface cables are used The product is potentially susceptible to certain EMC phenomena To mitigate against them it is recommended that the following measures be undertaken e The user is advised that mobile phones should not be used within 10m of the product when in use e The user is advised to take ESD precautions when handling the equipment This product does not represent an ideal reference design for an end product and does not fulf
14. pends on the product s quality grade as indicated below Standard Computers office equipment communications equipment test and measurement equipment audio and visual equipment home electronic appliances machine tools personal electronic equipment and industrial robots etc High Quality Transportation equipment automobiles trains ships etc traffic control systems anti disaster systems anti crime systems and safety equipment etc Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct threat to human life or bodily injury artificial life support devices or systems surgical implantations etc or may cause serious property damages nuclear reactor control systems military equipment etc You must check the quality grade of each Renesas Electronics product before using it in a particular application You may not use any Renesas Electronics product for any application for which itis not intended Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for which the product is not intended by Renesas Electronics 6 You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics especially with respect to the maximum rating operating supply voltage range movement power voltage range heat radiation charact
15. required at the start of tightening Tightening a screw too much may break the screw hole of the NQPACK or lead to a faulty connection by cracking solder on the NQPACK side e Failure of conduction during operation may be due to a crack in the solder for the NQPACK Check conduction with a tester and re solder the NQPACK as required R20UT2935EJ0100 Rev 1 00 Mar 1 2015 Page 4 of 8 7tENESAS ROE5571MLDMBO0O1 User s Manual 6 Dimensions of the Debugging MCU Board Figures 4 shows the dimensions and reference pad pattern of the debugging MCU board ROE5571MLDMBO01 0 50x35 17 50 a 2 0 25 c g Co Cd i i of o S oj w a Unit mm Figure 4 Reference Foot Pattern and Dimensions of This Product ROE5571MLDMBO01 R20UT2935EJ0100 Rev 1 00 Page 5 of 8 Mar 1 2015 RENESAS ROE5571MLDMB0O1 User s Manual 7 Notes on Usage READ the following warnings before using the debugging MCU board Incorrect operation will damage the debugging MCU board and user system The USER PROGRAM will be LOST Notes on Connecting the Debugging MCU Board e Cables must not be connected or removed while the power is on e Before connecting the debugging MCU board and user system check that the pin locations on both sides are correctly aligned with each other Note on Rewriting the Flash Memory
16. ve Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations 9 Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture use or sale is prohibited under any applicable domestic or foreign laws or regulations You should not use Renesas Electronics products or technology described in this document for any purpose relating to military applications or use by the military including but not limited to the development of weapons of mass destruction When exporting the Renesas Electronics products or technology described in this document you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations 10 Itis the responsibility of the buyer or distributor of Renesas Electronics products who distributes disposes of or otherwise places the product with a third party to notify such third party in advance of the contents and conditions set forth in this document Renesas Electronics assumes no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics products 11 This document may not be reproduced or duplicated in any form in whole or in part without prior written consent of Renesas Electronics 12 Please contact a Renesas Electronics sales office if you have any questions
17. ze of the MCU installed on the debugging MCU board is 4M Note that if the MCU to be debugged has the ROM size less than 4M access can be made to the differential areas Notes on Designing the User System e Pull the levels on the EMLE pin down to 4 7 kQ to 10 kQ e Pull the levels on the MD pin up to 4 7 kQ to 10 kQ and select the single chip mode e The output of the reset circuit of the user system must be open collector Note on the Flash Programming Software Products Flash Development Toolkit Renesas Flash Programmer etc e Do not use the flash programming software products when using the debugging MCU board Note on the Writing the On chip Flash Memory Mode e Do not use the writing the on chip flash memory mode when using the debugging MCU board Note on the A D Converter e The characteristics of the A D converter differ from those of actual MCU because there are a converter board and other devices between the MCU and the user system Note on the Hot Plug in Function e Do not use the hot plug in function when using the debugging MCU board R20UT2935EJ0100 Rev 1 00 Page 6 of 8 Mar 1 2015 RENESAS ROE5571MLDMB0O1 User s Manual Precautions This product is only intended for use in a laboratory environment under ambient temperature and humidity conditions A safe separation distance should be used between this and any sensitive equipment Its use outside the laboratory classroom study area or similar such area inva
Download Pdf Manuals
Related Search