Extech 461825 Photo Tachometer / Stroboscope Manual
Contents
1. by the number of reflective tape pieces for accurate measurement data MEMORY RECORD AND RECALL The 461825 can record Maximum Minimum and Last Reading for the period of time during which the Measure Trigger button is held These stored values can then be read directly on the meter s display The memory will automatically erase after approximately 10 seconds of meter inactivity Access the memory data immediately after the measurements 1 2 3 Follow the instructions for normal operation Release the Measurement Trigger button Immediately press the Memory Recall button once to display the Last Reading taken during the measurement period LA will alternately display with the data reading to indicate Last Reading Release and press the Memory Recall button again to display the Maximum reading taken during the measurement period UP will alternately appear with the data reading to indicate Max reading Release and press the Memory Recall button again to display the Minimum reading taken during the 30 second test period dn will alternately appear with the data reading to indicate Min reading 4 461825 Ver 1 2 03 05 Specifications General Specifications Custom LSI microprocessor based design Display Reversible 0 4 10mm 5 digit 99999 count LCD display RPM revolutions or rotations per minute units Memory Recall Records Recalls Max Min Last readings with memory push button Operating 32 to 122 F 02. resulting from action of the user such as misuse improper wiring operation outside of specification improper maintenance or repair or unauthorized modification Extech specifically disclaims any implied warranties or merchantability or fitness for a specific purpose and will not be liable for any direct indirect incidental or consequential damages Extech s total liability is limited to repair or replacement of the product The warranty set forth above is inclusive and no other warranty whether written or oral is expressed or implied Calibration and Repair Services Extech offers repair and calibration services for the products we sell Extech also provides NIST certification for most products Call the Customer Service Department for information on calibration services available for this product Extech recommends that annual calibrations be performed to verify meter performance and accuracy ry Support line 781 890 7440 Technical support Extension 200 E mail support extech com Repair amp Returns Extension 210 E mail repair extech com Product specifications subject to change without notice For the latest version of this User s Guide Software updates and other up to the minute product information visit our website www extech com Extech Instruments Corporation 285 Bear Hill Rd Waltham MA 02451 Copyright 2005 Extech Instruments Corporation All rights reserved including the right of reproduction in wh
3. User s Guide EXT INSTRUMENTS Combination Photo Tachometer Stroboscope Model 461825 MEMORY Introduction Congratulations on your purchase of Extech s Combination Photo Tachometer Stroboscope This professional meter with proper care will provide years of safe reliable service Meter Description Tachometer Light Source LCD Display Measure trigger button Memory Recall button FINE adjust knob COARSE adjust knob Range Function select switch Stroboscope flash tube ONDOARWN Note Battery compartment is on rear of meter 2 461825 Ver 1 2 03 05 Operation STROBOSCOPE MEASUREMENT PROCEDURE Select the Stroboscope Function and Range using the Range Function Select Switch The switch has four positions three of which are stroboscope dedicated with white range numbers The fourth position is Photo Tachometer dedicated and is labeled as such Speed Measurements 1 Remove power to the moving object under test and affix a target mark on the area to be measured 2 Apply power to the moving object and press the stroboscope s Measure Trigger Button 3 Aim the Stroboscope light beam toward the marked area on the object under test 4 Use the FINE and COARSE adjust knobs to synchronize or stop the motion of the object s mark A single stationary image of the mark provides actual speed measurement data NOTE Care must be taken to ensure that the mark is providing a 1 1 measurement This i
4. ole or in part in any form 6 461825 Ver 1 2 03 05
5. s done by checking that there is only one mark and not two four or more stationary marks on the object under test Two or more stopped marks indicate harmonic measurements 2 1 3 1 4 1 etc which provide a doubling tripling or quadrupling of the actual speed A useful method of avoiding harmonic measurements is to adjust the FINE COARSE knobs until two images marks appear and then lower the flash rate via COARSE FINE knobs until a single stationary image appears This is the actual speed Inspecting a moving object Measure the speed of a moving object as described above and move the FINE adjust knob alternately higher and lower to visually inspect all areas of the device 3 461825 Ver 1 2 03 05 PHOTO TACHOMETER MEASUREMENT PROCEDURE Select the Photo Tachometer function by moving the Range Function select switch to the PHOTO position Affix a small piece approx 0 5 of supplied reflective tape to the object under test Press the meter s Measurement Trigger button and align the Photo Tachometer light source with the reflective tape mark on the moving object Wait until the Monitor Indicator appears in the upper left hand corner of the LCD indicating that synchronization has occurred Release the Measure Trigger button only after the reading has stabilized approx 2 seconds NOTE To obtain better accuracy for low RPM measurements less than 50 RPM use more than one piece of reflective tape Divide the meter reading
6. to 50 C Temperature Operating lt 80 RH Humidity Four 1 5V AA batteries UM 3 or equivalent Electrical Specifications Measurement Range 5 to 99 999 RPM for the Tachometer 100 to 100 000 FPM RPM for the Stroboscope poe ee RPM lt 1000 RPM and 1 RPM gt 1000 RPM 0 1 2 digits Photo Tachometer detection 2 to 6 50 to 150mm typical distance Note Detection distances up to 12 300mm are possible depending upon ambient light Stroboscopic Flash rate 100 to 100 000 FPM flashes per minute Stroboscopic Flash adjust Range A 100 to 1 000 FPM range Range B 1000 to 10 000 FPM Range C 10 000 to 100 000 FPM Stroboscopic Flash duration 60 to 1000 microseconds approx 16 of period 5 461825 Ver 1 2 03 05 Warranty EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and workmanship for one year from date of shipment a six month limited warranty applies to sensors and cables If it should become necessary to return the instrument for service during or beyond the warranty period contact the Customer Service Department at 781 890 7440 ext 210 for authorization or visit our website www extech com for contact information A Return Authorization RA number must be issued before any product is returned to Extech The sender is responsible for shipping charges freight insurance and proper packaging to prevent damage in transit This warranty does not apply to defects
Download Pdf Manuals
Related Search