60W LED MOVING HEAD SPOT
Contents
1. Show Atelier MHCTPYKUMA NO SKCIJIYATALIUN Dragon Effects IS120 MH Irigy Clfecfs Thank you very much for choosing our product For safety purpose please read this manual carefully before your operation This manual included installation and using information Please install and operate it according to this manual 1 Technology Reference 1 Voltage 100 240V 50 60Hz 2 Power consumption 180W 3 LED ultra bright 120W LED 4 Color wheel 8 colors white spilt colors rainbow effect Gobo wheel 1 7 static gobos white rainbow effect gobo shake Dimmer Strobe Dimmer 1 20t s 5 Focus Electronic Focus 6 Pan 540 Tilt 270 7 Control DMX 512 16 CHs 8 Working mode Stand alone mode Controller mode Master Slave synchronization mode 9 Other function Pan Tilt speed adjustable Housing High temperature resistant engineering plastic aluminum alloy 10 Weight 8 9KG 11 Product Size 240 245 360mm 12 Packing Size 350 340 340mm Accessories The accessories below were packed with product please check if they are once open the package Power cable 1PCS User manual 1 PCS Clamp Optional 2PCS Warning Please check whether the light with damage by shipment once open the package before operation If product with damage by shipment please do not operate the light then contact the dealer or supplier This product is designed for Indoor use the IP rate is IP20 Keep the product in dry envi2. cause damage 5 General troubleshooting Phenomenon Solution Fixture can not start to work 1 Check if the power fuse burnout Fixture light normally but no responding to the DMX controller 1 Check if the DMX start address is correct 2 Check if the XLR signal cable was damaged Fixture work intermittently Check if the fan work well Whether dust blocked fan and fan nets Dark light brightness decreases obviously 1 Check whether the internal and external optical system clean Beam is not pure have a halo Clean the dust and oil of bulb lens and other parts The beam distortion serious 1 Check whether the lens is broken 2 Clean the dust or oil of lens 10
3. ation shall comply with all relevant standards 2 Function Setting LED display instruction Mode 1 A001 is factory default setting In this mode receive DMX512 signal control Press ENTER to set ID address Use UP or DOWN to change the value of ID address then press ENTER to save Address 001 x MENU UP DOWN ENTER 3 DMX CHANNEL CONTROL There are two modes to get DMX 512 signal for this fixture the one is 16 CHs and the other Please find the details as follow Basic Mode 16 channel SCH Decreasing speed 6CH Dimmer 0 100 No function Strobe effect slow Strobe 6 249 to fast 250 255 No function 0 19 Open White 30 39 dark blue 50 59 orange 70 79 light green 90 99 light blue 110 119 red 130 139 green Colour 150 159 pink 170 179 yellow Forwards rainbow 180 219 effect from fast to slow Backwards 220 255 rainbow effect from slow to fast 0 100 step by 1 256 Colour Offset Forwards gobo 160 199 rotation from fast to slow Backwards gobo 200 255 rotation from slow to fast or Gobo Stake 0255 Forwards gobo rotation from fast Gobo Rot to slow Backwards gobo 138 255 rotation from slow to fast 14CH Prism Prism rot a rotation 2 127 from fast to slow Backwards 128 255 rotation from slow to fast Control 200 239 4 Maintenance When the lens have fracture and other damage it should be replaced in time when the fixture can t start to run please che
4. ck if the fuse of power supply is burnout if it is burnout please install the fitted corresponding specification fuse with 5 x20 T2A 250 v 5 mmx20mm Note it must use the same specifications fuse The is installed with overheating protection device when it is overheat the overheating protection device will automatically cut off power supply Please check whether the fan running whether the fan and fan nets have dust jam find troubleshooting before working But note that a qualified technicians can do the repair work In order to maintain the gobo wheel smooth rotation and smooth movement it is suggested to add grease for the rotation gobo wheel every two months Should use good quality grease In order to ensure the fixture working well maintain the cleanness of fixture is very necessary It should be clean once every 30 days after cooling the fans Internal and external optical lens reflector and coating color filter cleaning must be carried out periodically to optimize the output light efficiency Do not use any contains chemical solvent cleaning coating color filter Cleaning the fixture depending on the operating frequency of fixture and the surrounding environment Clean with a soft cloth and cleaning products for glass suggest to clean the external optical system at least once every 30 days clean the internal optical system at least once every 30 60 days Please do not use alcohol and other organic solvents to wipe housing lest
5. r cord overlap on the other wire When not use or to clean the fixture please unplug the power cord Don t unplug the plug rudely or drag the power cord directly Keep the bulb clean do not contact with the glass bulb by hand directly Equipped with insurance rope connecting hole at the bottom of the fixture for security please use safety cable to hang the fixture There is no any parts for repair inside the fixture Before starting operation of the fixture please check whether all the cover plate or housing has been installed well whether the screw has been tighten Prohibit use the fixture when the cover plate or housing is opened If you have any questions or Suggestions please contact with dealers or supplier Important before any installation maintenance and clean the fixture please confirm the power supply is cut off Power supply connection The power cord connection as follows 3 L live wire brown wire E ground yellow green double color line N middle line blue line Connecting power supply please pay attention to the power supply voltage and frequency should be marked on the voltage and frequency of fixture When more than one moving head light used at the same time it is recommended that the power of the fixture respectively connection this can control the fixture ON OFF separately Important Connect to the power supply the ground yellow green line should be safety grounding electrical install
6. ronment Avoid in damp overheating or much dusty environment Prevent fixture in contact with the water and other liquids Please do not install the fixture on the surface of combustible substances Qualified professionals can install operate and maintain the fixture and to make sure strictly in accordance with the procedures described in this operating instructions 2 The fixture should be installed in a well ventilated place and the distance from the wall to keep above 10 cm at the same time please check the fan and the vent is unimpeded Do not use the fixture is directly projected on combustible objects the distance between the fixture and light objects please keep over 1 meter Don t look straight into the light source of the fixture especially for epilepsy patients so as not to cause damage to the eyes Please do not open and fix the fixture by yourself For electrical parts connected person must have the corresponding qualifications before operate For electrical parts connected person must have the corresponding qualifications before operate Before installation please make sure the power supply voltage you used and the voltage of fixture is identified Every fixture should be properly grounded and in accordance with the relevant standard for electrical installation Don t dispatch the fixture connected to any other dimming device Do not use insulating layer with damage for the power cord and don t take the powe
Download Pdf Manuals
Related Search